Initialize the gpio chip's of_node to the device's node
to work with DT based system.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The chained handler was set for the platform device with id == 0.
When the gpio devices are instantiated by a device tree, all have id ==
-1 and so the handler was unset resulting in unusable gpio irqs on
i.MX21 and i.MX27 (when using oftree).
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Without this, modules can't use this API, leading to build failures.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Not paying attention to the value being set is a bad thing because it
means that we'll not set the hardware up to reflect what was requested.
Not setting the hardware up to reflect what was requested means that the
caller won't get the results they wanted.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The feature GPIO_MSM_V1 is only available on three SoCs. On all other MSM SoCs
the INT_GPIO_GROUP{1,2} is undeclared, but Kconfig does allow such
configurations. Therefore the produced configuration is valid, but does not
compile. The problem is fixed by adding the missing Kconfig constraints.
drivers/gpio/gpio-msm-v1.c: In function âmsm_init_gpioâ:
drivers/gpio/gpio-msm-v1.c:629:26: error: 'INT_GPIO_GROUP1' undeclared
drivers/gpio/gpio-msm-v1.c:630:26: error: 'INT_GPIO_GROUP2' undeclared
Signed-off-by: Christian Dietrich <christian.dietrich@informatik.uni-erlangen.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If there is no platform data available, the driver shouldn't use the
pointer or it will oops. Since things will mostly work nonetheless,
(the BIOS may have set up the pins properly), I'd better not fail the
probe even in this case.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Currently the gpio _runtime_resume/suspend functions are calling the
get_context_loss_count() platform function if the function is populated for
a gpio bank. This function is used to determine if the gpio bank logic state
needs to be restored due to a power transition. This function will be populated
for all banks, but it should only be called for banks that have the
"loses_context" variable set. It is pointless to call this if loses_context is
false as we know the context will never be lost and will not need restoring.
For all OMAP2+ devices gpio bank-0 is in an always-on power domain and so will
never lose context. We found that the get_context_loss_count() was being called
for bank-0 during the probe and returning 1 instead of 0 indicating that the
context had been lost. This was causing the context restore function to be
called at probe time for this bank and because the context had never been saved,
was restoring an invalid state. This ultimately resulted in a crash [1].
This issue is a regression that was exposed by commit 1b1287032 (gpio/omap: fix
missing check in *_runtime_suspend()).
There are multiple bugs here that need to be addressed ...
1. Why the always-on power domain returns a context loss count of 1? This needs
to be fixed in the power domain code [2]. However, the gpio driver should not
assume the loss count is 0 to begin with.
2. The omap gpio driver should never be calling get_context_loss_count for a
gpio bank in a always-on domain. This is pointless and adds unneccessary
overhead.
3. The OMAP gpio driver assumes that the initial power domain context loss count
will be 0 at the time the gpio driver is probed. However, it could be
possible that this is not the case and an invalid context restore could be
performed during the probe. To avoid this only populate the
get_context_loss_count() function pointer after the initial call to
pm_runtime_get() has occurred. This will ensure that the first
pm_runtime_put() initialised the loss count correctly.
This patch addresses issues 2 and 3 above.
[1] http://marc.info/?l=linux-omap&m=134065775323775&w=2
[2] http://marc.info/?l=linux-omap&m=134100413303810&w=2
Cc: Kevin Hilman <khilman@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.walleij@stericsson.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: Franky Lin <frankyl@broadcom.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: NeilBrown <neilb@suse.de>
Reported-by: Franky Lin <frankyl@broadcom.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Franky Lin <frankyl@broadcom.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Tested-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Move irq_domain_add_legacy call from imx*-dt.c into gpio driver and
have the gpio driver adopt irqdomain support for both DT and non-DT
boot.
With all imx platform code converted from static gpio irq number
computation to use run-time gpio_to_irq call, we can now use
irq_alloc_descs and irqdomain support to dynamically get irq_base
and have the mapping between gpio and irq number available without
using virtual_irq_start and MXC_GPIO_IRQ_START.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
It seems that currently GPIO module is not working correctly during idle
when debounce is enabled - the system almost never responds to button
presses (observed on OMAP3530 ES2.1 and OMAP3630 ES1.2 pandora boards).
Even though wakeups are probably working, it seems that the GPIO module
itself is unable to detect input events and generate interrupts.
OMAP35x TRM also states that:
"If the debounce clock is inactive, the debounce cell gates all
input signals and thus cannot be used."
So whenever we are disabling debounce clocks (for PM or other reasons),
be sure the module's debounce feature is disabled too.
Cc: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Should be 'exynos5_xxx' instead of 'exonys5_xxx'.
It happened at the commit 30b842889e ("Merge tag 'soc2' of
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc")
during v3.5 merge window.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
[ My bad - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull MIPS updates from Ralf Baechle:
"The whole series has been sitting in -next for quite a while with no
complaints. The last change to the series was before the weekend the
removal of an SPI patch which Grant - even though previously acked by
himself - appeared to raise objections. So I removed it until the
situation is clarified. Other than that all the patches have the acks
from their respective maintainers, all MIPS and x86 defconfigs are
building fine and I'm not aware of any problems introduced by this
series.
Among the key features for this patch series is a sizable patchset for
Lantiq which among other things introduces support for Lantiq's
flagship product, the FALCON SOC. It also means that the opensource
developers behind this patchset have overtaken Lantiq's competing
inhouse development team that was working behind closed doors.
Less noteworthy the ath79 patchset which adds support for a few more
chip variants, cleanups and fixes. Finally the usual dose of tweaking
of generic code."
Fix up trivial conflicts in arch/mips/lantiq/xway/gpio_{ebu,stp}.c where
printk spelling fixes clashed with file move and eventual removal of the
printk.
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (81 commits)
MIPS: lantiq: remove orphaned code
MIPS: Remove all -Wall and almost all -Werror usage from arch/mips.
MIPS: lantiq: implement support for FALCON soc
MTD: MIPS: lantiq: verify that the NOR interface is available on falcon soc
MTD: MIPS: lantiq: implement OF support
watchdog: MIPS: lantiq: implement OF support and minor fixes
SERIAL: MIPS: lantiq: implement OF support
GPIO: MIPS: lantiq: convert gpio-stp-xway to OF
GPIO: MIPS: lantiq: convert gpio-mm-lantiq to OF and of_mm_gpio
GPIO: MIPS: lantiq: move gpio-stp and gpio-ebu to the subsystem folder
MIPS: pci: convert lantiq driver to OF
MIPS: lantiq: convert dma to platform driver
MIPS: lantiq: implement support for clkdev api
MIPS: lantiq: drop ltq_gpio_request() and gpio_to_irq()
OF: MIPS: lantiq: implement irq_domain support
OF: MIPS: lantiq: implement OF support
MIPS: lantiq: drop mips_machine support
OF: PCI: const usage needed by MIPS
MIPS: Cavium: Remove smp_reserve_lock.
MIPS: Move cache setup to setup_arch().
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Rh0r
-----END PGP SIGNATURE-----
Merge tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
"Besides the usual cleanups, this one brings:
* Support for 5 new chipsets: Intel's ICH LPC and SCH Centerton,
ST-E's STAX211, Samsung's MAX77693 and TI's LM3533.
* Device tree support for the twl6040, tps65910, da9502 and ab8500
drivers.
* Fairly big tps56910, ab8500 and db8500 updates.
* i2c support for mc13xxx.
* Our regular update for the wm8xxx driver from Mark."
Fix up various conflicts with other trees, largely due to ab5500 removal
etc.
* tag 'mfd-3.5-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (106 commits)
mfd: Fix build break of max77693 by adding REGMAP_I2C option
mfd: Fix twl6040 build failure
mfd: Fix max77693 build failure
mfd: ab8500-core should depend on MFD_DB8500_PRCMU
gpio: tps65910: dt: process gpio specific device node info
mfd: Remove the parsing of dt info for tps65910 gpio
mfd: Save device node parsed platform data for tps65910 sub devices
mfd: Add r_select to lm3533 platform data
gpio: Add Intel Centerton support to gpio-sch
mfd: Emulate active low IRQs as well as active high IRQs for wm831x
mfd: Mark two lm3533 zone registers as volatile
mfd: Fix return type of lm533 attribute is_visible
mfd: Enable Device Tree support in the ab8500-pwm driver
mfd: Enable Device Tree support in the ab8500-sysctrl driver
mfd: Add support for Device Tree to twl6040
mfd: Register the twl6040 child for the ASoC codec unconditionally
mfd: Allocate twl6040 IRQ numbers dynamically
mfd: twl6040 code cleanup in interrupt initialization part
mfd: Enable ab8500-gpadc driver for Device Tree
mfd: Prevent unassigned pointer from being used in ab8500-gpadc driver
...
This adds support for the spear13xx platform, which has first been under
review a long time ago and finally been completed after generic spear
work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=W2Ri
-----END PGP SIGNATURE-----
Merge tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc: soc specific changes (part 2) from Olof Johansson:
"This adds support for the spear13xx platform, which has first been
under review a long time ago and finally been completed after generic
spear work has gone into the clock, dt and pinctrl branches.
Also a number of updates for the samsung socs are part of this branch."
Fix up trivial conflicts in drivers/gpio/gpio-samsung.c that look much
worse than they are: the exonys5 init code was refactored in commit
fd454997d6 ("gpio: samsung: refactor gpiolib init for exynos4/5"), and
then commit f10590c983 ("ARM: EXYNOS: add GPC4 bank instance") added a
new gpio chip define and did tiny updates to the init code.
So the conflict diff looks like hell, but it's actually a fairly simple
change.
* tag 'soc2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (34 commits)
ARM: exynos: fix building with CONFIG_OF disabled
ARM: EXYNOS: Add AUXDATA for i2c controllers
ARM: dts: Update device tree source files for EXYNOS5250
ARM: EXYNOS: Add device tree support for interrupt combiner
ARM: EXYNOS: Add irq_domain support for interrupt combiner
ARM: EXYNOS: Remove a new bus_type instance for EXYNOS5
ARM: EXYNOS: update irqs for EXYNOS5250 SoC
ARM: EXYNOS: Add pre-divider and fout mux clocks for bpll and mpll
ARM: EXYNOS: add GPC4 bank instance
ARM: EXYNOS: Redefine IRQ_MCT_L0,1 definition
ARM: EXYNOS: Modify the GIC physical address for static io-mapping
ARM: EXYNOS: Add watchdog timer clock instance
pinctrl: SPEAr1310: Fix pin numbers for clcd_high_res
SPEAr: Update MAINTAINERS and Documentation
SPEAr13xx: Add defconfig
SPEAr13xx: Add compilation support
SPEAr13xx: Add dts and dtsi files
pinctrl: Add SPEAr13xx pinctrl drivers
pinctrl: SPEAr: Create macro for declaring GPIO PINS
SPEAr13xx: Add common clock framework support
...
These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=WeDQ
-----END PGP SIGNATURE-----
Merge tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm-soc device tree conversions (part 2) from Olof Johansson:
"These continue the device tree work from part 1, this set is for the
tegra, mxs and imx platforms, all of which have dependencies on clock
or pinctrl changes submitted earlier."
Fix up trivial conflicts due to nearby changes in
drivers/{gpio/gpio,i2c/busses/i2c}-mxs.c
* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (73 commits)
ARM: dt: tegra: invert status=disable vs status=okay
ARM: dt: tegra: consistent basic property ordering
ARM: dt: tegra: sort nodes based on bus order
ARM: dt: tegra: remove duplicate device_type property
ARM: dt: tegra: consistenly use lower-case for hex constants
ARM: dt: tegra: format regs properties consistently
ARM: dt: tegra: gpio comment cleanup
ARM: dt: tegra: remove unnecessary unit addresses
ARM: dt: tegra: whitespace cleanup
ARM: dt: tegra cardhu: fix typo in SDHCI node name
ARM: dt: tegra: cardhu: register core regulator tps62361
ARM: dt: tegra30.dtsi: Add SMMU node
ARM: dt: tegra20.dtsi: Add GART node
ARM: dt: tegra30.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra20.dtsi: Add Memory Controller(MC) nodes
ARM: dt: tegra: Add device tree support for AHB
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
...
This is a follow-up to ae79c1904 "[PATCH v2] Add support for TCA6424"
merged in the v3.5 merge window. It fixes comments made when the
patch was merged.
- Use 3 byte transfers instead of two separate transfers (2+1 byte)
- An unnecessary cast removed
Signed-off-by: Andreas Schallenberg <Andreas.Schallenberg@3alitytechnica.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Lots of gpio changes, both to core code and drivers. Changes do touch
architecture code to remove the need for separate arm/gpio.h includes
in most architectures. Some new drivers are added, and a number of
gpio drivers are converted to use irq_domains for gpio inputs used as
interrupts. Device tree support has been amended to allow multiple
gpio_chips to use the same device tree node. Remaining changes are
primarily bug fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=U6hj
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO driver changes from Grant Likely:
"Lots of gpio changes, both to core code and drivers.
Changes do touch architecture code to remove the need for separate
arm/gpio.h includes in most architectures.
Some new drivers are added, and a number of gpio drivers are converted
to use irq_domains for gpio inputs used as interrupts. Device tree
support has been amended to allow multiple gpio_chips to use the same
device tree node.
Remaining changes are primarily bug fixes."
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (33 commits)
gpio/generic: initialize basic_mmio_gpio shadow variables properly
gpiolib: Remove 'const' from data argument of gpiochip_find()
gpio/rc5t583: add gpio driver for RICOH PMIC RC5T583
gpiolib: quiet gpiochip_add boot message noise
gpio: mpc8xxx: Prevent NULL pointer deref in demux handler
gpio/lpc32xx: Add device tree support
gpio: Adjust of_xlate API to support multiple GPIO chips
gpiolib: Implement devm_gpio_request_one()
gpio-mcp23s08: dbg_show: fix pullup configuration display
Add support for TCA6424A
gpio/omap: (re)fix wakeups on level-triggered GPIOs
gpio/omap: fix broken context restore for non-OFF mode transitions
gpio/omap: fix missing check in *_runtime_suspend()
gpio/omap: remove cpu_is_omapxxxx() checks from *_runtime_resume()
gpio/omap: remove suspend/resume callbacks
gpio/omap: remove retrigger variable in gpio_irq_handler
gpio/omap: remove saved_wakeup field from struct gpio_bank
gpio/omap: remove suspend_wakeup field from struct gpio_bank
gpio/omap: remove saved_fallingdetect, saved_risingdetect
gpio/omap: remove virtual_irq_start variable
...
Conflicts:
drivers/gpio/gpio-samsung.c
Here's the driver core, and other driver subsystems, pull request for
the 3.5-rc1 merge window.
Outside of a few minor driver core changes, we ended up with the
following different subsystem and core changes as well, due to
interdependancies on the driver core:
- hyperv driver updates
- drivers/memory being created and some drivers moved into it
- extcon driver subsystem created out of the old Android staging switch
driver code
- dynamic debug updates
- printk rework, and /dev/kmsg changes
All of this has been tested in the linux-next releases for a few weeks
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAk+7q28ACgkQMUfUDdst+ykXmwCfcPASzC+/bDkuqdWsqzxlWZ7+
VOQAnAriySv397St36J6Hz5bMQZwB1Yq
=SQc+
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg Kroah-Hartman:
"Here's the driver core, and other driver subsystems, pull request for
the 3.5-rc1 merge window.
Outside of a few minor driver core changes, we ended up with the
following different subsystem and core changes as well, due to
interdependancies on the driver core:
- hyperv driver updates
- drivers/memory being created and some drivers moved into it
- extcon driver subsystem created out of the old Android staging
switch driver code
- dynamic debug updates
- printk rework, and /dev/kmsg changes
All of this has been tested in the linux-next releases for a few weeks
with no reported problems.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
Fix up conflicts in drivers/extcon/extcon-max8997.c where git noticed
that a patch to the deleted drivers/misc/max8997-muic.c driver needs to
be applied to this one.
* tag 'driver-core-3.5-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (90 commits)
uio_pdrv_genirq: get irq through platform resource if not set otherwise
memory: tegra{20,30}-mc: Remove empty *_remove()
printk() - isolate KERN_CONT users from ordinary complete lines
sysfs: get rid of some lockdep false positives
Drivers: hv: util: Properly handle version negotiations.
Drivers: hv: Get rid of an unnecessary check in vmbus_prep_negotiate_resp()
memory: tegra{20,30}-mc: Use dev_err_ratelimited()
driver core: Add dev_*_ratelimited() family
Driver Core: don't oops with unregistered driver in driver_find_device()
printk() - restore prefix/timestamp printing for multi-newline strings
printk: add stub for prepend_timestamp()
ARM: tegra30: Make MC optional in Kconfig
ARM: tegra20: Make MC optional in Kconfig
ARM: tegra30: MC: Remove unnecessary BUG*()
ARM: tegra20: MC: Remove unnecessary BUG*()
printk: correctly align __log_buf
ARM: tegra30: Add Tegra Memory Controller(MC) driver
ARM: tegra20: Add Tegra Memory Controller(MC) driver
printk() - restore timestamp printing at console output
printk() - do not merge continuation lines of different threads
...
Parse the gpio specific device node information locally.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This patch adds the Intel Centerton processor device ID for GPIO.
The device ID is defined in include/linux/pci_ids.h
Signed-off-by: Seth Heasley <seth.heasley@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. but the payback comes later when adding
new boards can be done by only providing new device trees instead.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HIfz
-----END PGP SIGNATURE-----
Merge tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull arm soc-specific pinctrl changes from Olof Johansson:
"With this, five platforms are moving to the relatively new pinctrl
subsystem for their pin management, replacing the older soc specific
in-kernel interfaces with common code.
There is quite a bit of net addition of code for each platform being
added to the pinctrl subsystem. But the payback comes later when
adding new boards can be done by only providing new device trees
instead."
Fix up trivial conflicts in arch/arm/mach-ux500/{Makefile,board-mop500.c}
* tag 'pinctrl' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (61 commits)
mtd: nand: gpmi: fix compile error caused by pinctrl call
ARM: PRIMA2: select PINCTRL and PINCTRL_SIRF in Kconfig
ARM: nomadik: enable PINCTRL_NOMADIK where needed
ARM: mxs: enable pinctrl support
video: mxsfb: adopt pinctrl support
ASoC: mxs-saif: adopt pinctrl support
i2c: mxs: adopt pinctrl support
mtd: nand: gpmi: adopt pinctrl support
mmc: mxs-mmc: adopt pinctrl support
serial: mxs-auart: adopt pinctrl support
serial: amba-pl011: adopt pinctrl support
spi/imx: adopt pinctrl support
i2c: imx: adopt pinctrl support
can: flexcan: adopt pinctrl support
net: fec: adopt pinctrl support
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
...
Three new system-on-chip models are supported: the st-ericsson u9540
in ux500, the sam9n12 in at91 and the emma ev2 in shmobile.
Emma is a little bit special because it is completely unrelated to
the classic shmobile models, but the new Renesas rmobile SoCs are a
combination of things from both Emma and shmobile, so it was decided to
have them all live in one directory.
This also contains updates to existing shmobile soc code as well as some
related board changes due to dependencies.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=5TAz
-----END PGP SIGNATURE-----
Merge tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull support for new arm SoCs from Olof Johansson:
"Three new system-on-chip models are supported: the st-ericsson u9540
in ux500, the sam9n12 in at91 and the emma ev2 in shmobile.
Emma is a little bit special because it is completely unrelated to the
classic shmobile models, but the new Renesas rmobile SoCs are a
combination of things from both Emma and shmobile, so it was decided
to have them all live in one directory.
This also contains updates to existing shmobile soc code as well as
some related board changes due to dependencies."
* tag 'soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (23 commits)
mach-shmobile: Use DT_MACHINE for KZM9D V3
mach-shmobile: Emma Mobile EV2 DT support V3
mach-shmobile: KZM9D board Ethernet support V3
mach-shmobile: Emma Mobile EV2 GPIO support V3
mach-shmobile: Emma Mobile EV2 SMP support V3
mach-shmobile: KZM9D board support V3
mach-shmobile: Emma Mobile EV2 SoC base support V3
gpio: Emma Mobile GPIO driver V2
ARM: mach-shmobile: sh73a0: fixup PINT/IRQ16-IRQ31 irq number conflict
ARM: mach-shmobile: clock-r8a7740: use followparent_recalc on usb24s
ARM: mach-shmobile: clock-r8a7740: add MMCIF clock
ARM: mach-shmobile: clock-r8a7740: add SDHI clock
ARM: mach-shmobile: clock-r8a7740: add USB clock
ARM: mach-shmobile: clock-r8a7740: add FSI clock
ARM: mach-shmobile: r8a7740: cleanup I2C workaround method
ARM: mach-shmobile: r8a7740: add gpio_irq support
ARM: mach-shmobile: sh7372: Add FSI DMAEngine support
ARM / mach-shmobile: Use preset_lpj with calibrate_delay()
ARM: ux500: ioremap differences for DB9540
ARM: ux500: core U9540 support
...
The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game of
booting using device trees, which is a great step forward for them. at91
and spear have pretty much completed this process with a huge amount of
work being put into at91. The other platforms are continuing the process.
We finally start to see the payback on this investment, as new machines
are getting supported purely by adding a .dts source file that can be
completely independent of the kernel source.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=7DYv
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull device tree conversions for arm-soc, part 1, from Olof Johansson:
"The spear3xx, lpc32xx, shmobile and mmp platforms are joining the game
of booting using device trees, which is a great step forward for them.
at91 and spear have pretty much completed this process with a huge
amount of work being put into at91. The other platforms are
continuing the process.
We finally start to see the payback on this investment, as new
machines are getting supported purely by adding a .dts source file
that can be completely independent of the kernel source."
Fix up trivial conflict in arch/arm/Kconfig
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits)
ARM: at91: Add ADC driver to at91sam9260/at91sam9g20 dtsi files
arm/dts: omap4-panda: Add LEDs support
arm/dts: omap4-sdp: Add LEDs support
arm/dts: twl4030: Add twl4030-gpio node
OMAP4: devices: Do not create mcpdm device if the dtb has been provided
OMAP4: devices: Do not create dmic device if the dtb has been provided
Documentation: update docs for mmp dt
ARM: dts: refresh dts file for arch mmp
ARM: mmp: support pxa910 with device tree
ARM: mmp: support mmp2 with device tree
gpio: pxa: parse gpio from DTS file
ARM: mmp: support DT in timer
ARM: mmp: support DT in irq
ARM: mmp: append CONFIG_MACH_MMP2_DT
ARM: mmp: fix build issue on mmp with device tree
ARM: ux500: Enable PRCMU Timer 4 (clocksource) for Device Tree
ARM: ux500: Disable SMSC911x platform code registration when DT is enabled
ARM: ux500: Fork cpu-db8500 platform_devs for sequential DT enablement
ARM: ux500: Do not attempt to register non-existent i2c devices on Snowball
ARM: SPEAr3xx: Correct keyboard data passed from DT
...
Implements OF support and add code to load custom properties from the DT.
The Serial To Parallel (STP) is found on MIPS based Lantiq socs. It is a
peripheral controller used to drive external shift register cascades. At most
3 groups of 8 bits can be driven. The hardware is able to allow the DSL modem
to drive the 2 LSBs of the cascade automatically. Newer socs are also able to
automatically drive some pins via the internal PHYs. The driver currently only
supports output functionality. Patches for the input feature found on newer
generations of the soc will be provided in a later series.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3839/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Implements OF support and convert to of_mm_gpio.
By attaching hardware latches to the External Bus Unit (EBU) on Lantiq SoC, it
is possible to create output only gpios. This driver configures a special
memory address, which when written to, outputs 16 bit to the latches.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3840/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Move the 2 drivers from arch/mips/lantiq/xway/ to the subsystem and make them
buildable.
The following 2 patches will convert the drivers to OF.
Signed-off-by: John Crispin <blogic@openwrt.org>
Cc: linux-kernel@vger.kernel.org
Cc: linux-mips@linux-mips.org
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Patchwork: https://patchwork.linux-mips.org/patch/3838/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
The modern idiom is to use irq_domain to allocate interrupts. This is
useful partly to allow further infrastructure to be based on the domains
and partly because it makes it much easier to allocate virtual interrupts
to devices as we don't need to allocate a contiguous range of interrupt
numbers.
Convert the wm831x driver over to this infrastructure, using a legacy
IRQ mapping if an irq_base is specified in platform data and otherwise
using a linear mapping, always registering the interrupts even if they
won't ever be used. Only boards which need to use the GPIOs as
interrupts should need to use an irq_base.
This means that we can't use the MFD irq_base management since the
unless we're using an explicit irq_base from platform data we can't rely
on a linear mapping of interrupts. Instead we need to map things via
the irq_domain - provide a conveniencem function wm831x_irq() to save a
small amount of typing when doing so. Looking at this I couldn't clearly
see anything the MFD core could do to make this nicer.
Since we're not supporting device tree yet there's no meaningful
advantage if we don't do this conversion in one, the fact that the
interrupt resources are used for repeated IP blocks makes accessor
functions for the irq_domain more trouble to do than they're worth.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Make the gpio-tps65910 as platform driver and register
this from tps65910 core driver as mfd sub device.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
This change removes the read/write callback functions in favor of common
regmap accessors inside the header file. This change also makes use of
regmap_read/write for single register access which maps better onto what this
driver actually needs.
Signed-off-by: Rhyland Klein <rklein@nvidia.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
It fixes the issue in gpio-generic that commit fb14921 (gpio/mxc: add
missing initialization of basic_mmio_gpio shadow variables) manged to
fix in gpio-mxc driver, so that other platform specific drivers do not
suffer from the same problem over and over again.
Changes since v1:
* Turn the last parameter of bgpio_init() "bool big_endian" into
"unsigned long flags" and give those really quirky hardwares a
chance to tell that reg_set and reg_dir are unreadable.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
[grant.likely: Fix big-endian usage to explicitly set BBGPIOF_BIG_ENDIAN]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit 3d0f7cf0 "gpio: Adjust of_xlate API to support multiple GPIO
chips" changed the api of gpiochip_find to drop const from the data
parameter of the match hook, but didn't also drop const from data
causing a build warning.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The PMIC device RC5T583 from RICOH supports 8 gpios.
Adding gpio driver for this device to access the pins
control through gpio library.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
[grant.likely: slight cosmetic changes]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The pr_info message in gpiochip_add gets displayed for every
gpiochip registered. When first bringing up a system this
information could be helpful but for normal use it's just a
bunch of noise. Change the message to a pr_debug.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit cfadd838(powerpc/8xxx: Fix interrupt handling in MPC8xxx GPIO
driver) added an unconditional call of chip->irq_eoi() to the demux
handler.
This leads to a NULL pointer derefernce on MPC512x platforms which use
this driver as well.
Make it conditional.
Reported-by: Thomas Wucher <thwucher@linutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Felix Radensky <felix@embedded-sol.com>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: stable@vger.kernel.org
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds device tree support for gpio-lpc32xx.c.
To register the various GPIO banks as (struct) gpio_chips via the same DT
gpio-controller, we utilize the adjusted of_xlate API to manipulate the
actually used struct gpio_chip.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch changes the of_xlate API to make it possible for multiple
gpio_chips to refer to the same device tree node. This is useful for
banked GPIO controllers that use multiple gpio_chips for a single
device. With this change the core code will try calling of_xlate on
each gpio_chip that references the device_node and will return the
gpio number for the first one to return 'true'.
Tested-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Allow drivers to use the modern request and configure idiom together
with devres.
As with plain gpio_request() and gpio_request_one() we can't implement
the old school version in terms of _one() as this would force the
explicit selection of a direction in gpio_request() which could break
systems if we pick the wrong one. Implementing devm_gpio_request_one()
in terms of devm_gpio_request() would needlessly complicate things or
lead to duplication from the unmanaged version depending on how it's
done.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Pullups are enabled when bits are set, not when cleared.
Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch extends the PCA953x driver to support TI's TCA6424A 24 bit I2C I/O expander. The patch is based on code by Michele
Bevilacqua.
Changes in v2:
- Compare ngpio against 24 in both places, not >16
- Larger datatype now u32 instead of uint.
Bit fields not used for struct members since their address is taken.
- Be precise: TCA6424A (untested for older TCA6424)
Signed-off-by: Andreas Schallenberg<Andreas.Schallenberg@3alitytechnica.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
commit 1b1287032 (gpio/omap: fix missing check in *_runtime_suspend())
broke wakeups on level-triggered GPIOs by adding the enabled
non-wakeup GPIO check before the workaround that enables wakeups
on level-triggered IRQs, effectively disabling that workaround.
To fix, move the enabled non-wakeup GPIO check after the
level-triggered IRQ workaround.
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The fix in commit 1b1287032 (gpio/omap: fix missing check in
*_runtime_suspend()) exposed another bug in the context restore path.
Currently, the per-bank context restore happens whenever the context
loss count is different in runtime suspend and runtime resume *and*
whenever the per-bank contex_loss_count == 0:
if (context_lost_cnt_after != bank->context_loss_count ||
!context_lost_cnt_after) {
omap_gpio_restore_context(bank);
Restoring context when the context_lost_cnt_after == 0 is clearly
wrong, since this will be true until the first off-mode transition
(which could be never, if off-mode is never enabled.) This check
causes the context to be restored on *every* runtime PM transition.
Before commit 1b1287032 (gpio/omap: fix missing check in
*_runtime_suspend()), this code was never executed in non-OFF mode, so
there were never spurious context restores happening. After that
change though, spurious context restores could happen.
To fix, simply remove the !context_lost_cnt_after check. It is not
needed.
This bug was found when noticing that the smc911x NIC on 3530/Overo
was not working, and git bisect tracked it down to this patch. It
seems that the spurious context restore was causing the smsc911x to
not be properly probed on this platform.
Tested-by: Tony Lindgren <tony@atomide.com>
Acked-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This patch is V2 of the Emma Mobile GPIO driver. This
driver is designed to be reusable between multiple SoCs
that share the same basic building block, but so far it
has only been used on Emma Mobile EV2.
Each driver instance handles 32 GPIOs with individually
maskable IRQs. The driver operates on two I/O memory
ranges and the 32 GPIOs are hooked up to two interrupts.
In the case of Emma Mobile EV2 this GPIO building block
is used as main external interrupt controller hooking up
159 GPIOS as 159 interrupts via 5 driver instances and
10 interrupts to the GIC and the Cortex-A9 Dual.
Signed-off-by: Magnus Damm <damm@opensource.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Add GPC4 bank instance which is included in rev1 of EXYNOS5.
Signed-off-by: Sangsu Park <sangsu4u.park@samsung.com>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* 'mxs/dt/for-3.5' of git://git.linaro.org/people/shawnguo/linux-2.6: (51 commits)
ARM: dts: enable audio support for imx28-evk
ARM: dts: enable i2c device for imx28-evk
i2c: mxs: add device tree probe support
ARM: dts: enable mmc for imx28-evk
ARM: dts: enable mmc for imx23-evk
mmc: mxs-mmc: add device tree support
mmc: mxs-mmc: copy wp_gpio in struct mxs_mmc_host
mmc: mxs-mmc: have dma_channel than dma_res in mxs_mmc_host
mmc: mxs-mmc: use devm_* helper to make cleanup simpler
mmc: mxs-mmc: move header from mach into linux folder
mmc: mxs-mmc: get rid of the use of cpu_is_xxx
mmc: mxs-mmc: let ssp_is_old take host as parameter
mmc: mxs-mmc: use global stmp_device functionality
ARM: mxs: add gpio support for device tree boot
gpio/mxs: add device tree probe
gpio/mxs: get rid of the use of cpu_is_xxx
gpio/mxs: use devm_* helpers to make error handling simple
ARM: mxs: add mxs-dma dt support
ARM: mxs: do not add dma device by default
dma: mxs-dma: add device tree probe support
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=xjdL
-----END PGP SIGNATURE-----
Merge tag 'ux500-gpio-pins-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/pinctrl
ux500 GPIO and pinctrl changes for kernel 3.5
* tag 'ux500-gpio-pins-for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: switch MSP to using pinctrl for pins
ARM: ux500: alter MSP registration to return a device pointer
ARM: ux500: switch to using pinctrl for uart0
ARM: ux500: delete custom pin control system
ARM: ux500: switch over to Nomadik pinctrl driver
pinctrl: add sleep state definition
pinctrl/nomadik: implement pin configuration
pinctrl/nomadik: implement pin multiplexing
pinctrl/nomadik: reuse GPIO debug function for pins
pinctrl/nomadik: break out single GPIO debug function
pinctrl/nomadik: basic Nomadik pinctrl interface
pinctrl/nomadik: !CONFIG_OF build error
gpio: move the Nomadik GPIO driver to pinctrl
Context conflicts resolved in drivers/pinctrl/Kconfig and
drivers/pinctrl/Makefile.
Signed-off-by: Olof Johansson <olof@lixom.net>
It removes the use of cpu_is_xxx from gpio-mxs driver and instead use
platform_device_id to identify the device. Accordingly, mxs platform
code is changed to register gpio device with different names, and
the registeration are done in soc specific initialization functions
now, so postcore_initcall(mxs_add_mxs_gpio) gets removed.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
It uses devm_* helpers to make the error handling of probe clean
and simple.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Fixes the following compiler warnings:
drivers/gpio/gpio-samsung.c: In function ‘samsung_gpiolib_init’:
drivers/gpio/gpio-samsung.c:2980:1: warning: label ‘err_ioremap1’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2978:1: warning: label ‘err_ioremap2’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2976:1: warning: label ‘err_ioremap3’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2974:1: warning: label ‘err_ioremap4’ defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2722:55: warning: unused variable ‘gpio_base4’ [-Wunused-variable]
drivers/gpio/gpio-samsung.c:455:32: warning: ‘exynos_gpio_cfg’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2126:33: warning: ‘exynos4_gpios_1’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2228:33: warning: ‘exynos4_gpios_2’ defined but not used [-Wunused-variable]
drivers/gpio/gpio-samsung.c:2373:33: warning: ‘exynos4_gpios_3’ defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Jean-Francois Dagenais reported:
Configuring a gpio pin with the gpio-pch driver with
"IRQF_TRIGGER_LOW | IRQF_ONESHOT" generates an interrupt storm for
threaded ISR until the ISR thread actually gets to physically clear
the interrupt on the triggering chip!! The immediate observable
symptom is the high CPU usage for my ISR thread task and the
interrupt count in /proc/interrupts incrementing radically.
The driver is wrong in several ways:
1) Using handle_simple_irq() does not provide proper flow control
handling. In the case of oneshot threaded handlers for the
demultiplexed interrupts this results in an interrupt storm because
the simple handler does not deal with masking/unmasking. Even
without threaded oneshot handlers an interrupt storm for level type
interrupts can easily be triggered when the interrupt is disabled
and the interrupt line is activated from the device.
2) Acknowlegding the demultiplexed interrupt before calling the
handler is wrong for level type interrupts.
3) The set_type function unconditionally enables the interrupt. It's
supposed to set the type and nothing else. The unmasking is done by
the core code.
Move the acknowledge code into a separate function and add it to the
demux irqchip callbacks.
Remove the unconditional enabling from the set_type() callback and set
the proper flow handlers depending on the selected type (level/edge).
Reported-and-tested-by: Jean-Francois Dagenais <jeff.dagenais@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We do checking for bank->enabled_non_wakeup_gpios in order
to skip redundant operations. Somehow, the check got missed
while doing the cleanup series.
Just to make sure that we do context restore correctly in
*_runtime_resume(), the bank->workaround_enabled check is
moved after context restore. Otherwise, it would prevent
context restore when bank->enabled_non_wakeup_gpios is 0.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Add register offsets for GPIO_IRQSTATUS_RAW_0, GPIO_IRQSTATUS_RAW_0
which are present on OMAP4+ processors. Now we can distinguish
conditions applicable to OMAP4,5 and those specific to OMAP24xx
and OMAP3xxx.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Both omap_gpio_suspend() and omap_gpio_resume() does programming
of wakeup_en register.
_gpio_rmw(base, bank->regs->wkup_en, 0xffffffff, 0);
_gpio_rmw(base, bank->regs->wkup_en, bank->context.wake_en, 1);
This is redundant in omap_gpio_suspend() because wakeup_en
register automatically gets initialized in _set_gpio_wakeup()
and set_gpio_trigger() while being called either from
chip.irq_set_wake() or chip.irq_set_type().
This is also redundant in omap_gpio_resume() because wakeup_en
register is programmed in omap_gpio_restore_context() called
which is called from runtime resume callback.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
commit 672e302e3c (ARM: OMAP: use edge/level handlers from generic IRQ
framework) removed retrigger support in favor of using generic IRQ
framework. This patch cleans up some unused remnants of that removal.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
There is no more need to have saved_wakeup because bank->context.wake_en
already holds that value. So getting rid of read/write operation associated
with this field.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Since we already have bank->context.wake_en to keep track
of gpios which are wakeup enabled, there is no need to have
this field any more.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Since we already have context.fallingdetect and context.risingdetect
there is no more need to have these additional fields. Also, getting
rid of extra reads associated with them.
Cc: Kevin Hilman <khilman@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Cousson, Benoit <b-cousson@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Tested-by: Govindraj.R <govindraj.raja@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Rather than requiring architectures that use gpiolib but don't have any
need to define anything custom to copy an asm/gpio.h provide a Kconfig
symbol which architectures must select in order to include gpio.h and
for other architectures just provide the trivial implementation directly.
This makes it much easier to do gpiolib updates and is also a step towards
making gpiolib APIs available on every architecture.
For architectures with existing boilerplate code leave a stub header in
place which warns on direct inclusion of asm/gpio.h and includes
linux/gpio.h to catch code that's doing this. Direct inclusion of
asm/gpio.h has long been deprecated.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Jonas Bonn <jonas@southpole.se>
Acked-by: Tony Luck <tony.luck@intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add gpio support for Intel MSIC chips found in Intel Medfield platforms.
MSIC supports totally 24 GPIOs with 16 low voltage and 8 high voltage pins.
Driver uses MSIC mfd interface for MSIC access.
(Updated comment to indicate why locking is actually safe)
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Only code move, no functional change.
Main reason to do this was to get rid of the warnings:
drivers/gpio/gpio-samsung.c: In function 'samsung_gpiolib_init':
drivers/gpio/gpio-samsung.c:2974:1: warning: label 'err_ioremap4' defined but not used [-Wunused-label]
drivers/gpio/gpio-samsung.c:2722:47: warning: unused variable 'gpio_base4' [-Wunused-variable]
without adding more ifdef mess.
I think this whole file would do well being coverted over to a platform
driver and moving most of the tables out to SoC code and/or device trees,
but since that changes init ordering it needs to be done with some care,
i.e. not at this time.
Signed-off-by: Olof Johansson <olof@lixom.net>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
I'm moving this driver over to the pinctrl subsystem to convert
the custom pin mux/config scheme over to use pinctrl.
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The IRQ status register should be re-read after each iteration.
Otherwise the loop misses the interrupt if it gets raised immediately
after handled.
Reported-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Initialization of irqenable, irqstatus registers is the common
operation done in this function for all OMAP platforms, viz. OMAP1,
OMAP2+. The latter _gpio_rmw()'s which supposedly got introduced
wrongly to take care of OMAP2+ platforms were overwriting initially
programmed OMAP1 value breaking functionality on OMAP1.
Somehow incorrect assumption was made that each _gpio_rmw()'s were
mutually exclusive. On close observation it is found that the first
_gpio_rmw() which is supposedly done to take care of OMAP1 platform
is generic enough and takes care of OMAP2+ platform as well.
Therefore remove the latter _gpio_rmw() to irqenable as they are
redundant now.
Writing to ctrl and debounce_en registers for OMAP2+ platforms are
modified to match the original(pre-cleanup) code where the registers
are initialized with 0. In the cleanup series since we are using
_gpio_rmw(reg, 0, 1), instead of __raw_writel(), we are just reading
and writing the same values to ctrl and debounce_en. This is not an
issue for debounce_en register because it has 0x0 as the default value.
But in the case of ctrl register the default value is 0x2 (GATINGRATIO
= 0x1) so that we end up writing 0x2 instead of intended 0 value.
Therefore changing back to __raw_writel() as this is sufficient for
this case besides simpler to understand.
Also, change irqstatus initalization logic that avoids comparison
with bool, besides making it fit in a single line.
Cc: stable@vger.kernel.org
Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Reported-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Tested-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This introduces 128 gpio bits (for each PCI device installed) with
working interrupt support.
Signed-off-by: Alessandro Rubini <rubini@gnudd.com>
Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
irq_domain already provides a facility to translate from hardware IRQ
numbers to Linux IRQ numbers so use that instead of open-coding the logic
in the driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This driver works on many Intel chipsets, including the ICH6, ICH7,
ICH8, ICH9, ICH10, 3100, Series 5/3400 (Ibex Peak), Series 6/C200
(Cougar Point), and NM10 (Tiger Point).
Additional Intel chipsets should be easily supported if needed, eg the
ICH1-5, EP80579, etc.
Tested on QM67 (Cougar Point), QM57 (Ibex Peak), 3100 (Whitmore Lake),
and NM10 (Tiger Point).
Includes work from Jean Delvare:
- Resource leak removal during module load/unload
- GPIO API bit value enforcement
Also includes code cleanup from Guenter Roeck and Grant Likely.
Signed-off-by: Peter Tyser <ptyser@xes-inc.com>
Signed-off-by: Aaron Sierra <asierra@xes-inc.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
In 3.3, gpio wakeup setting was broken. The call
enable_irq_wake() didn't set up the PXA gpio registers
(PWER, ...) anymore.
Fix it at least for pxa27x. The driver doesn't seem to be
used in pxa25x (weird ...), and the fix doesn't extend to
pxa3xx and pxa95x (which don't have a gpio_set_wake()
available).
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Add irq domain support to the gpio-nomadik GPIO driver. This
enables its users to support dynamic IRQ assignment, which is
requried by Device Tree.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This creates Device Tree bindings for the Nomadik GPIO driver.
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
We were using a custom io_p2v() (physical-to-virtual) translation
macro, but it's fully possible to just ioremap() this memory
now, so skip use of static addresses altogether.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Low EMI (Electro-Magnetic Interference) mode means lower slew
rate on the signals. The Nomadik GPIO controller supports
this so create an interface to enable it.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
If the pin is switching to altfunc, and there was an interrupt
installed on it which has been lazy disabled, actually mask the
interrupt to prevent spurious interrupts that would occur while
the pin is under control of the peripheral. Only SKE does this.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Cache two more registers in the GPIO controller.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi KASAGAR <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Setting GPIOs' SLPM value to 1 (WAKEUP_DISABLE) is seen to cause
increased power consumption in sleep/deep-sleep. So remove the code
which disables SLPM based on the wakeup settings and only ensure
it is on as needed.
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Recent pinctrl discussions concluded that gpiolib APIs should in fact do
whatever is required to mux a GPIO onto pins, by calling pinctrl APIs if
required. This change implements this for the Tegra GPIO driver, and removes
calls to the Tegra-specific APIs from drivers and board files.
Cc: Chris Ball <cjb@laptop.org>
Cc: linux-mmc@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Chris Ball <cjb@laptop.org> # for sdhci-tegra.c
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Olof Johansson <olof@lixom.net>
When a Tegra GPIO is used as an IRQ, it should be enabled as a GPIO (so
the pinmux module isn't driving it as an output) and configured as a GPIO
input (so the GPIO module isn't driving it as an output). Set this up
automatically whenever an IRQ is requested, so that users of IRQs don't
need to do this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Fixes the following warning when "SAMSUNG EXYNOS5" is not selected:
warning: ‘exynos5_gpios_1’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_2’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_3’ defined but not used [-Wunused-variable]
warning: ‘exynos5_gpios_4’ defined but not used [-Wunused-variable]
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The variable 'bit' is uninitialized in the first iteration of for
loop. Fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The irqdomain api changed significantly in v3.4 which caused a build
failure for this driver.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Cc: Hans J. Koch <hjk@linutronix.de>
Cc: Torben Hohn <torbenh@linutronix.de>
The code in drivers/of/gpio.c isn't shared by any other subsystem since it
is all gpiolib specific. drivers/gpio is a better place to maintain these
functions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Linus Walleij <linus.walleij@stericsson.com>
This patch converts the drivers in drivers/gpio/* to use
module_pci_driver() macro which makes the code smaller and a bit
simpler by having less boilerplate.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The Kconfig description and help text doesn't list all of the devices
supported by this driver. This patch adds the PCA957x devices.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The boot firmware might leave the registers configured causing interrupts
to happen even when no handler for them is yet registered. Fix this by
clearing the IRQ edge detect registers at init.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Since x86 is using SPARSE_IRQ by default nowadays it means that we need to
allocate IRQ descriptors dynamically using irq_alloc_descs() otherwise the
genirq code fails to convert our irq numbers to suitable descriptors.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use devm_* helper functions where possible to make the error handling in
the probe function simpler.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Introduce new flags to automatically export GPIOs when using the convenience
functions gpio_request_one() or gpio_request_array(). This eases support for
custom boards where lots of GPIOs need to be exported for customer
applications.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
When Tegra30 support was added to the Tegra GPIO driver, a few places
which iterated over all banks were not converted to use the variable
tegra_gpio_bank_count rather than hard-coding the bank count. Fix this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Tegra20 and Tegra30 share the same register layout within registers, but
the addresses of the registers is a little different. Fix the driver to
cope with this.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Olof Johansson <olof@lixom.net>
Pull more ARM updates from Russell King.
This got a fair number of conflicts with the <asm/system.h> split, but
also with some other sparse-irq and header file include cleanups. They
all looked pretty trivial, though.
* 'for-linus' of git://git.linaro.org/people/rmk/linux-arm: (59 commits)
ARM: fix Kconfig warning for HAVE_BPF_JIT
ARM: 7361/1: provide XIP_VIRT_ADDR for no-MMU builds
ARM: 7349/1: integrator: convert to sparse irqs
ARM: 7259/3: net: JIT compiler for packet filters
ARM: 7334/1: add jump label support
ARM: 7333/2: jump label: detect %c support for ARM
ARM: 7338/1: add support for early console output via semihosting
ARM: use set_current_blocked() and block_sigmask()
ARM: exec: remove redundant set_fs(USER_DS)
ARM: 7332/1: extract out code patch function from kprobes
ARM: 7331/1: extract out insn generation code from ftrace
ARM: 7330/1: ftrace: use canonical Thumb-2 wide instruction format
ARM: 7351/1: ftrace: remove useless memory checks
ARM: 7316/1: kexec: EOI active and mask all interrupts in kexec crash path
ARM: Versatile Express: add NO_IOPORT
ARM: get rid of asm/irq.h in asm/prom.h
ARM: 7319/1: Print debug info for SIGBUS in user faults
ARM: 7318/1: gic: refactor irq_start assignment
ARM: 7317/1: irq: avoid NULL check in for_each_irq_desc loop
ARM: 7315/1: perf: add support for the Cortex-A7 PMU
...
Primarily gpio device driver changes with some minor side effects
under arch/arm and arch/x86. Also includes a few core changes such as
explicitly supporting (electrical) open source and open drain outputs
and some help for parsing gpio devicetree properties.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=BSW8
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull GPIO changes for v3.4 from Grant Likely:
"Primarily gpio device driver changes with some minor side effects
under arch/arm and arch/x86. Also includes a few core changes such as
explicitly supporting (electrical) open source and open drain outputs
and some help for parsing gpio devicetree properties."
Fix up context conflict due to Laxman Dewangan adding sleep control for
the tps65910 driver separately for gpio's and regulators.
* tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6: (34 commits)
gpio/ep93xx: Remove unused inline function and useless pr_err message
gpio/sodaville: Mark broken due to core irqdomain migration
gpio/omap: fix redundant decoding of gpio offset
gpio/omap: fix incorrect update to context.irqenable1
gpio/omap: fix incorrect context restore logic in omap_gpio_runtime_*
gpio/omap: fix missing dataout context save in _set_gpio_dataout_reg
gpio/omap: fix _set_gpio_irqenable implementation
gpio/omap: fix trigger type to unsigned
gpio/omap: fix wakeup_en register update in _set_gpio_wakeup()
gpio: tegra: tegra_gpio_config shouldn't be __init
gpio/davinci: fix enabling unbanked GPIO IRQs
gpio/davinci: fix oops on unbanked gpio irq request
gpio/omap: Fix section warning for omap_mpuio_alloc_gc()
ARM: tegra: export tegra_gpio_{en,dis}able
gpio/gpio-stmpe: Fix the value returned by _get_value routine
Documentation/gpio.txt: Explain expected pinctrl interaction
GPIO: LPC32xx: Add output reading to GPO P3
GPIO: LPC32xx: Fix missing bit selection mask
gpio/omap: fix wakeups on level-triggered GPIOs
gpio/omap: Fix IRQ handling for SPARSE_IRQ
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=onDl
-----END PGP SIGNATURE-----
Merge tag 'mfd_3.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6
Pull MFD changes from Samuel Ortiz:
- 4 new drivers: Freescale i.MX on-chip Anatop, Ricoh's RC5T583 and
TI's TPS65090 and TPS65217.
- New variants support (8420, 8520 ab9540), cleanups and bug fixes for
the abx500 and db8500 ST-E chipsets.
- Some minor fixes and update for the wm8994 from Mark.
- The beginning of a long term TWL cleanup effort coming from the TI
folks.
- Various fixes and cleanups for the s5m, TPS659xx, pm860x, and MAX8997
drivers.
Fix up trivial conflicts due to duplicate patches and header file
cleanups (<linux/device.h> removal etc).
* tag 'mfd_3.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (97 commits)
gpio/twl: Add DT support to gpio-twl4030 driver
gpio/twl: Allocate irq_desc dynamically for SPARSE_IRQ support
mfd: Detach twl6040 from the pmic mfd driver
mfd: Replace twl-* pr_ macros by the dev_ equivalent and do various cleanups
mfd: Micro-optimization on twl4030 IRQ handler
mfd: Make twl4030 SIH SPARSE_IRQ capable
mfd: Move twl-core IRQ allocation into twl[4030|6030]-irq files
mfd: Remove references already defineid in header file from twl-core
mfd: Remove unneeded header from twl-core
mfd: Make twl-core not depend on pdata->irq_base/end
ARM: OMAP2+: board-omap4-*: Do not use anymore TWL6030_IRQ_BASE in board files
mfd: Return twl6030_mmc_card_detect IRQ for board setup
Revert "mfd: Add platform data for MAX8997 haptic driver"
mfd: Add support for TPS65090
mfd: Add some da9052-i2c section annotations
mfd: Build rtc5t583 only if I2C config is selected to y.
mfd: Add anatop mfd driver
mfd: Fix compilation error in tps65910.h
mfd: Add 8420 variant to db8500-prcmu
mfd: Add 8520 PRCMU variant to db8500-prcmu
...
This branch contains a handful of driver updates, mostly to
the LPC32xx platform but also for Samsung EXYNOS and Davinci.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=TkGm
-----END PGP SIGNATURE-----
Merge tag 'drivers2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: More SoC driver updates" from Olof Johansson:
"This branch contains a handful of driver updates, mostly to the
LPC32xx platform but also for Samsung EXYNOS and Davinci.
It had a few context conflicts against patches already merged through
fixes-non-critical. We should have resolved this early during the
development cycle by pulling them in as a dependency, instead I did it
after the fact this time."
* tag 'drivers2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
gpio/samsung: use ioremap() for EXYNOS4 GPIOlib
gpio/samsung: add support GPIOlib for EXYNOS5250
ARM: EXYNOS: add support GPIO for EXYNOS5250
ARM: LPC32xx: Ethernet support
ARM: LPC32xx: USB Support
ARM: davinci: dm644x evm: add support for VPBE display
ARM: davinci: dm644x: add support for v4l2 video display
ARM: EXYNOS: Hook up JPEG PD to generic PD infrastructure
ARM: EXYNOS: Hook up G2D PD to generic PD infrastructure
arm: lpc32xx: phy3250: add rtc & touch device
ARM: LPC32xx: clock.c: Clock registration fixes
ARM: LPC32xx: clock.c: jiffies wrapping
ARM: LPC32xx: clock.c: Missing header file
ARM: LPC32XX: Remove broken non-static declaration
ARM: LPC32xx: clock.c: Fix mutex lock issues
ARM: LPC32xx: clock.c: warning fix
ARM: LPC32xx: Added lpc32xx_defconfig
Pull ARM platform updates from Russell King:
"This covers platform stuff for platforms I have a direct interest in
(iow, I have the hardware). Essentially:
- as we no longer support any other Acorn platforms other than RiscPC
anymore, we can collect all that code into mach-rpc.
- convert Acorn expansion card stuff to use IRQ allocation functions,
and get rid of NO_IRQ from there.
- cleanups to the ebsa110 platform to move some private stuff out of
its header files.
- large amount of SA11x0 updates:
- conversion of private DMA implementation to DMA engine support
(this actually gives us greater flexibility in drivers over the old
API.)
- re-worked ucb1x00 updates - convert to genirq, remove sa11x0
dependencies, fix various minor issues
- move platform specific sa11x0 framebuffer data into platform files
in arch/arm instead of keeping this in the driver itself
- update sa11x0 IrDA driver for DMA engine, and allow it to use DMA
for SIR transmissions as well as FIR
- rework sa1111 support for genirq, and irq allocation
- fix sa1111 IRQ support so it works again
- use sparse IRQ support
After this, I have one more pull request remaining from my current
set, which I think is going to be the most problematical as it
generates 8 conflicts."
Fixed up the trivial conflict in arch/arm/mach-rpc/Makefile as per
Russell.
* 'platforms' of git://git.linaro.org/people/rmk/linux-arm: (125 commits)
ARM: 7343/1: sa11x0: convert to sparse IRQ
ARM: 7342/2: sa1100: prepare for sparse irq conversion
ARM: 7341/1: input: prepare jornada720 keyboard and ts for sa11x0 sparse irq
ARM: 7340/1: rtc: sa1100: include mach/irqs.h instead of asm/irq.h
ARM: sa11x0: remove unused DMA controller definitions
ARM: sa11x0: remove old SoC private DMA driver
USB: sa1111: add hcd .reset method
USB: sa1111: add OHCI shutdown methods
USB: sa1111: reorganize ohci-sa1111.c
USB: sa1111: get rid of nasty printk(KERN_DEBUG "%s: ...", __FILE__)
USB: sa1111: sparse and checkpatch cleanups
ARM: sa11x0: don't static map sa1111
ARM: sa1111: use dev_err() rather than printk()
ARM: sa1111: cleanup sub-device registration and unregistration
ARM: sa1111: only setup DMA for DMA capable devices
ARM: sa1111: register sa1111 devices with dmabounce in bus notifier
ARM: sa1111: move USB interface register definitions to ohci-sa1111.c
ARM: sa1111: move PCMCIA interface register definitions to sa1111_generic.c
ARM: sa1111: move PS/2 interface register definitions to sa1111p2.c
ARM: sa1111: delete unused physical GPIO register definitions
...
These are all specific to some driver. They are typically the platform
side of a change in the drivers directory, such as adding a new driver
or extending the interface to the platform. In cases where there is no
maintainer for the driver, or the maintainer prefers to have the
platform changes in the same branch as the driver changes, the patches
to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in fuse.c.
In rtc-sa1100.c, the global removal of IRQF_DISABLED conflicts with
the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIVAwUAT24/Y2CrR//JCVInAQLUdw//V4pKPuKempSe1kuD2MJfqldHwEVOlAUt
of1IhLPAp8tpCscPDQ0yTy3ixquINg4jVnaDLL+E0quVbhLu6hlS2TYNKDEaVAAc
cPUtVEUdja7Cfu4+bXX2vcWM/UyI6Ax7bsUUcwu4wFnEsjA6qOSu/jYY4jXDguHq
ODGQSaSz0XQkfVBsWOlO8W/ejb0T3y+Ro3M/Vz5qJsMnZBR8R/i9aUYDFGiZ1GTn
3APHB7ALz6SS5/9SJS65PH16poBexcea5gyb3gnR1yt30kRmMTOAWrLC+JdyqFaO
7LHXW514+D1QbWV2gwNCWhQSLbgp9PWq/FXJtq4StW7tgNbDbj1d1Dc1GX+fvk2M
bBih1yWoIVx6CZWFBQ7gsbqVHUZ/sW2fo76yb8K5dVPXx0fL5lEkv5Xwk3gxbqt5
lPE8+z+jiL5D+8RK1DZQu1PfxzaMwDZkJkVoGLCcdyM7FvnX3LIYf2bqbcp+zrQL
lz9aht9C1k12R7feOX8emlluNd3eaKv/6jLrOasUP5wrJDam5hesSD5mLeTlAdxZ
U8XJe4L24dFv15/yrMCzcyes5EmB3aS3nfb9TsSfq22IOKo2PCQLCnL6Z/rfM+1p
mGu7BqdBnx3/8NkHdUrttMWjuPNh77MfPM6RO/E+TaBLHtwvKoLWJAHAYQNmt2xH
IbGcyorBD5s=
=pQ3X
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: driver specific updates" from Arnd Bergmann:
"These are all specific to some driver. They are typically the
platform side of a change in the drivers directory, such as adding a
new driver or extending the interface to the platform. In cases where
there is no maintainer for the driver, or the maintainer prefers to
have the platform changes in the same branch as the driver changes,
the patches to the drivers are included as well.
A much smaller set of driver updates that depend on other branches
getting merged first will be sent later.
The new export of tegra_chip_uid conflicts with other changes in
fuse.c. In rtc-sa1100.c, the global removal of IRQF_DISABLED
conflicts with the cleanup of the interrupt handling of that driver.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up aforementioned trivial conflicts.
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (94 commits)
ARM: SAMSUNG: change the name from s3c-sdhci to exynos4-sdhci
mmc: sdhci-s3c: add platform data for the second capability
ARM: SAMSUNG: support the second capability for samsung-soc
ARM: EXYNOS: add support DMA for EXYNOS4X12 SoC
ARM: EXYNOS: Add apb_pclk clkdev entry for mdma1
ARM: EXYNOS: Enable MDMA driver
regulator: Remove bq24022 regulator driver
rtc: sa1100: add OF support
pxa: magician/hx4700: Convert to gpio-regulator from bq24022
ARM: OMAP3+: SmartReflex: fix error handling
ARM: OMAP3+: SmartReflex: fix the use of debugfs_create_* API
ARM: OMAP3+: SmartReflex: micro-optimization for sanity check
ARM: OMAP3+: SmartReflex: misc cleanups
ARM: OMAP3+: SmartReflex: move late_initcall() closer to its argument
ARM: OMAP3+: SmartReflex: add missing platform_set_drvdata()
ARM: OMAP3+: hwmod: add SmartReflex IRQs
ARM: OMAP3+: SmartReflex: clear ERRCONFIG_VPBOUNDINTST only on a need
ARM: OMAP3+: SmartReflex: Fix status masking in ERRCONFIG register
ARM: OMAP3+: SmartReflex: Add a shutdown hook
ARM: OMAP3+: SmartReflex Class3: disable errorgen before disable VP
...
Conflicts:
arch/arm/mach-tegra/Makefile
arch/arm/mach-tegra/fuse.c
drivers/rtc/rtc-sa1100.c
Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=o5Xl
-----END PGP SIGNATURE-----
Merge tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull "ARM: global cleanups" from Arnd Bergmann:
"Quite a bit of code gets removed, and some stuff moved around, mostly
the old samsung s3c24xx stuff. There should be no functional changes
in this series otherwise. Some cleanups have dependencies on other
arm-soc branches and will be sent in the second round.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>"
Fixed up trivial conflicts mainly due to #include's being changes on
both sides.
* tag 'cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (121 commits)
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
ARM: EXYNOS: Add clock register addresses for EXYNOS4X12 bus devfreq driver
ARM: EXYNOS: add clock registers for exynos4x12-cpufreq
PM / devfreq: update the name of EXYNOS clock registers that were omitted
PM / devfreq: update the name of EXYNOS clock register
ARM: EXYNOS: change the prefix S5P_ to EXYNOS4_ for clock
ARM: EXYNOS: use static declaration on regarding clock
ARM: EXYNOS: replace clock.c for other new EXYNOS SoCs
ARM: OMAP2+: Fix build error after merge
ARM: S3C24XX: remove call to s3c24xx_setup_clocks
...
Minor removal of an unused inline function and a useless pr_err message.
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In preparation to convert SA1100 to sparse irq, set .nr_irqs for each machine
and explicitly include mach/irqs.h as needed.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sodaville driver doesn't build anymore due to the transition to
common irq_domain in the core code. It needs to be reworked, but
the rework isn't trivial. Since this is a new driver anyway for
v3.4, mark it as broken now and a fixup patch can re-enable it when
the rework change has been tested.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add the DT support for the I2C GPIO expander inside the twl4030.
Note: The pdata parameters still have to be properly adapted using
dedicated bindings.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Do not use the board pdata for irq_base, but allocate them dynamically
to allow a proper support of SPARSE_IRQ.
Fix an unneeded line wrap.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
twl4030 is using a two level irq controllers infrastruture.
So far, only the first level was using dynamic irq_desc allocation
to be able to have irq_domain support for device tree.
There is a need to allocate separate irq_descs for the SIH too to
avoid hacking the first level with interrupts from the second level.
Add an irq_base parameter to allow the caller to provide the base from
pdata or from dynamic allocation.
Affect TWL4030_NR_IRQS to the twl-core IRQs only.
Moreover that will allow the extraction of the of_node pointer for further
Device Tree conversion.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
Pull powerpc merge from Benjamin Herrenschmidt:
"Here's the powerpc batch for this merge window. It is going to be a
bit more nasty than usual as in touching things outside of
arch/powerpc mostly due to the big iSeriesectomy :-) We finally got
rid of the bugger (legacy iSeries support) which was a PITA to
maintain and that nobody really used anymore.
Here are some of the highlights:
- Legacy iSeries is gone. Thanks Stephen ! There's still some bits
and pieces remaining if you do a grep -ir series arch/powerpc but
they are harmless and will be removed in the next few weeks
hopefully.
- The 'fadump' functionality (Firmware Assisted Dump) replaces the
previous (equivalent) "pHyp assisted dump"... it's a rewrite of a
mechanism to get the hypervisor to do crash dumps on pSeries, the
new implementation hopefully being much more reliable. Thanks
Mahesh Salgaonkar.
- The "EEH" code (pSeries PCI error handling & recovery) got a big
spring cleaning, motivated by the need to be able to implement a
new backend for it on top of some new different type of firwmare.
The work isn't complete yet, but a good chunk of the cleanups is
there. Note that this adds a field to struct device_node which is
not very nice and which Grant objects to. I will have a patch soon
that moves that to a powerpc private data structure (hopefully
before rc1) and we'll improve things further later on (hopefully
getting rid of the need for that pointer completely). Thanks Gavin
Shan.
- I dug into our exception & interrupt handling code to improve the
way we do lazy interrupt handling (and make it work properly with
"edge" triggered interrupt sources), and while at it found & fixed
a wagon of issues in those areas, including adding support for page
fault retry & fatal signals on page faults.
- Your usual random batch of small fixes & updates, including a bunch
of new embedded boards, both Freescale and APM based ones, etc..."
I fixed up some conflicts with the generalized irq-domain changes from
Grant Likely, hopefully correctly.
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (141 commits)
powerpc/ps3: Do not adjust the wrapper load address
powerpc: Remove the rest of the legacy iSeries include files
powerpc: Remove the remaining CONFIG_PPC_ISERIES pieces
init: Remove CONFIG_PPC_ISERIES
powerpc: Remove FW_FEATURE ISERIES from arch code
tty/hvc_vio: FW_FEATURE_ISERIES is no longer selectable
powerpc/spufs: Fix double unlocks
powerpc/5200: convert mpc5200 to use of_platform_populate()
powerpc/mpc5200: add options to mpc5200_defconfig
powerpc/mpc52xx: add a4m072 board support
powerpc/mpc5200: update mpc5200_defconfig to fit for charon board
Documentation/powerpc/mpc52xx.txt: Checkpatch cleanup
powerpc/44x: Add additional device support for APM821xx SoC and Bluestone board
powerpc/44x: Add support PCI-E for APM821xx SoC and Bluestone board
MAINTAINERS: Update PowerPC 4xx tree
powerpc/44x: The bug fixed support for APM821xx SoC and Bluestone board
powerpc: document the FSL MPIC message register binding
powerpc: add support for MPIC message register API
powerpc/fsl: Added aliased MSIIR register address to MSI node in dts
powerpc/85xx: mpc8548cds - add 36-bit dts
...
In gpio_get(), _get_gpio_datain() and _get_gpio_dataout() get rid of
un-necessary operation to compute gpio mask. The gpio offset passed
to gpio_get() is sufficient to do that.
Here is Russell's original comment:
Can someone explain to me this:
static int _get_gpio_datain(struct gpio_bank *bank, int gpio)
{
void __iomem *reg = bank->base + bank->regs->datain;
return (__raw_readl(reg) & GPIO_BIT(bank, gpio)) != 0;
}
static int gpio_get(struct gpio_chip *chip, unsigned offset)
{
struct gpio_bank *bank = container_of(chip, struct gpio_bank, chip);
void __iomem *reg = bank->base;
int gpio = chip->base + offset;
u32 mask = GPIO_BIT(bank, gpio);
if (gpio_is_input(bank, mask))
return _get_gpio_datain(bank, gpio);
else
return _get_gpio_dataout(bank, gpio);
}
Given that bank->width on OMAP is either 32 or 16, and GPIO numbers for
any GPIO chip are always aligned to 32 or 16, why does this code bother
adding the chips base gpio number and then modulo the width?
Surely this means if - for argument sake - you registered a GPIO chip
with 8 lines followed by one with 16 lines, GPIO0..7 would be chip 0
bit 0..7, GPIO8..15 would be chip 1 bit 8..15, GPIO16..23 would be
chip 1 bit 0..7.
However, if you registered a GPIO chip with 16 lines first, it would
mean GPIO0..15 would be chip 0 bit 0..15, and GPIO16..31 would be
chip 1 bit 0..15.
Surely this kind of behaviour is not intended?
Is there a reason why the bitmask can't just be (1 << offset) where
offset is passed into these functions as GPIO number - chip->base ?
Reported-by: Russell King - ARM Linux <linux@arm.linux.org.uk>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In _enable_gpio_irqbank() when bank->regs->set_irqenable is TRUE,
gpio_mask can be directly set by writing to set_irqenable register
without overwriting current value. In order to ensure the same is
stored in context.irqenable1, we must avoid overwriting it with
gpio_mask at the end of the function. Instead, update irqenable1
appropriately by OR'ing with gpio_mask.
For the case where bank->regs->set_irqenable is FALSE, irqenable1
can be directly overwritten with 'l' which holds correct computed
value.
if (bank->regs->set_irqenable) {
reg += bank->regs->set_irqenable;
l = gpio_mask;
} else {
reg += bank->regs->irqenable;
l = __raw_readl(reg);
if (bank->regs->irqenable_inv)
l &= ~gpio_mask;
else
l |= gpio_mask;
}
Make similar change for _disable_gpio_irqbank().
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In omap_gpio_runtime_suspend/resume() the context save/restore should
be independent of bank->enabled_non_wakeup_gpios. This was preventing
context restore of GPIO lines which are not wakeup enabled.
Reported-by: Govindraj Raja <govindraj.raja@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
There are two functions, _set_gpio_dataout_reg() and _set_gpio_dataout_mask()
which writes to dataout register and the dataout context must be saved.
It is missing in the first function, _set_gpio_dataout_reg(). Fix this.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This function should be capable of both enabling and disabling interrupts
based upon the *enable* parameter. Right now the function only enables
the interrupt and *enable* is not used at all. So add the interrupt
disable capability also using the parameter.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The GPIO trigger parameter is of type unsigned.
enum {
IRQ_TYPE_NONE = 0x00000000,
IRQ_TYPE_EDGE_RISING = 0x00000001,
IRQ_TYPE_EDGE_FALLING = 0x00000002,
IRQ_TYPE_EDGE_BOTH = (IRQ_TYPE_EDGE_FALLING | IRQ_TYPE_EDGE_RISING),
IRQ_TYPE_LEVEL_HIGH = 0x00000004,
IRQ_TYPE_LEVEL_LOW = 0x00000008,
IRQ_TYPE_LEVEL_MASK = (IRQ_TYPE_LEVEL_LOW | IRQ_TYPE_LEVEL_HIGH),
IRQ_TYPE_SENSE_MASK = 0x0000000f,
IRQ_TYPE_PROBE = 0x00000010,
...
};
Even though gpio_irq_type(struct irq_data *d, unsigned type) has the right type
of parameter, the subsequent called functions set_gpio_triggering() and
set_gpio_trigger() wrongly makes it signed integer. Fix this.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
There are two ways through which wakeup_en register can be programmed
using gpiolib APIs as shown below. It is seen that in the second case
in _set_gpio_wakeup(), even though bank->suspend_wakeup is updated
correctly, its value is not programmed in wakeup_en register. Fix this.
irq_set_type()->gpio_irq_type()->_set_gpio_triggering()->set_gpio_trigger()
irq_set_wake()->gpio_wake_enable()->_set_gpio_wakeup()
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
This function is called from non-__init context, just like
tegra_gpio_enable()/disable(). Remove the __init annotation to avoid
section mismatch warnings during compile.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Initial board support for the GE IMP3A, a 3U compactPCI card with a p2020
processor.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
The GE GPIO driver provides basic support (set direction, read/write state)
for the GPIO provided on some GE single board computers. This patch moves
the driver from the 86xx specific platform directrory to the GPIO subsystem
so that it can be used on non-86xx boards.
Signed-off-by: Martyn Welch <martyn.welch@ge.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'next/soc-exynos5250-gpio' of git://git.kernel.org/pub/scm/linux/kernel/git/kgene/linux-samsung: (201 commits)
gpio/samsung: use ioremap() for EXYNOS4 GPIOlib
gpio/samsung: add support GPIOlib for EXYNOS5250
ARM: EXYNOS: add support GPIO for EXYNOS5250
(update to v3.3-rc7)
Conflicts:
arch/arm/mach-pxa/pxa25x.c
arch/arm/mach-pxa/pxa27x.c
The dummy clock for the pxa rtc in those files keeps getting added and
removed in various trees. Apparently removing is the correct solution.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* 'ep93xx-for-arm-soc' of git://github.com/RyanMallon/linux-2.6:
ep93xx: Remove unnecessary includes of ep93xx-regs.h
ep93xx: Move EP93XX_SYSCON defines to SoC private header
ep93xx: Move crunch code to mach-ep93xx directory
ep93xx: Make syscon access functions private to SoC
ep93xx: Configure GPIO ports in core code
ep93xx: Move peripheral defines to local SoC header
ep93xx: Convert the watchdog driver into a platform device.
ep93xx: Use ioremap for backlight driver
ep93xx: Move GPIO defines to gpio-ep93xx.h
ep93xx: Don't use system controller defines in audio drivers
ep93xx: Move PHYS_BASE defines to local SoC header file
(update to v3.3-rc7)
Conflicts:
arch/arm/mach-s3c2440/common.h
This patch changes to use ioremap() for EXYNOS4210
so that we can drop the static mapping for EXYNOS
SoCs.
Note: Will be updated for all of Samsung GPIOlibs
to use ioremap() next time.
Signed-off-by: Sangsu Park <sangsu4u.park@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds gpio_chips for EXYNOS5250 and replaces
exynos4_xxx() with exynos_xxx() and variables to support
exynos4 and exynos5 together.
In addition, use ioreamp() for base address of gpios.
Signed-off-by: Sangsu Park <sangsu4u.park@samsung.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Move the pinmux setting of the EP93xx GPIOs to the core code. This
removes the need for the GPIO driver to have access to the system
controller registers.
Signed-off-by: Ryan Mallon <rmallon@gmail.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Reviewed-by: Mika Westerberg <mika.westerberg@iki.fi>
Acked-by: Hartley Sweeten <hsweeten@visionengravers.com>
Unbanked GPIO IRQ handling code made a copy of just
the irq_chip structure for GPIO IRQ lines which caused
problems after the generic IRQ chip conversion because
there was no valid irq_chip_type structure with the
right "regs" populated. irq_gc_mask_set_bit() was
therefore accessing random addresses.
Fix it by making a copy of irq_chip_type structure
instead. This will ensure sane register offsets.
Cc: <stable@vger.kernel.org> # v3.0.x+
Reported-by: Jon Povey <Jon.Povey@racelogic.co.uk>
Tested-by: Jon Povey <Jon.Povey@racelogic.co.uk>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make omap_mpuio_alloc_gc() __devinit as omap_gpio_chip_init()
is __devinit. Otherwise we get:
WARNING: vmlinux.o(.devinit.text+0xa10): Section mismatch in reference
from the function omap_gpio_chip_init() to the function .init.text:omap_mpuio_alloc_gc()
The function __devinit omap_gpio_chip_init() references
a function __init omap_mpuio_alloc_gc().
If omap_mpuio_alloc_gc is only used by omap_gpio_chip_init then
annotate omap_mpuio_alloc_gc with a matching annotation.
Signed-off-by: Tony Lindgren <tony@atomide.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
These two functions are used in drivers that can be
modules, so they need to be exported.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Alan Ott <alan@signal11.us>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The present _get_value routine returns the contents of the GPIO Monitor Pin
Status Register(GPMR) starting from the bit whose value is requested to BIT 0
(irrelevant bits are replace by 0).
For e.g. if we request the value of GPIO 6 in the earlier implementation the
value returned is:
BIT6 followed by 6 0's
whereas it should just return BIT6.
This patch addresses the same.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The chip offers the function to detect the current state of output of the GPO
P3 pins. Useful for reading GPIO output state in Linux' GPIO API, e.g. via
sysfs.
Please note that this only reads back the currently programmed output state,
not the actual electrical level in terms of a GPI function. Finally, GPO3 is
still just an output.
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add missing mask to pin bit selection in gpio-lpc32xx.c
(#define GPIO3_PIN_IN_SEL)
Signed-off-by: Roland Stigge <stigge@antcom.de>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
While both level- and edge-triggered GPIOs are capable of generating
interrupts, only edge-triggered GPIOs are capable of generating a
module-level wakeup to the PRCM (c.f. 34xx NDA TRM section 25.5.3.2.)
In order to ensure that devices using level-triggered GPIOs as
interrupts can also cause wakeups (e.g. from idle), this patch enables
edge-triggering for wakeup-enabled, level-triggered GPIOs when a GPIO
bank is runtime-suspended (which also happens during idle.)
This fixes a problem found in GPMC-connected network cards with GPIO
interrupts (e.g. smsc911x on Zoom3, Overo, ...) where network booting
with NFSroot was very slow since the GPIO IRQs used by the NIC were
not generating PRCM wakeups, and thus not waking the system from idle.
NOTE: until v3.3, this boot-time problem was somewhat masked because
the UART init prevented WFI during boot until the full serial driver
was available. Preventing WFI allowed regular GPIO interrupts to fire
and this problem was not seen. After the UART runtime PM cleanups, we
no longer avoid WFI during boot, so GPIO IRQs that were not causing
wakeups resulted in very slow IRQ response times.
Tested on platforms using level-triggered GPIOs for network IRQs using
the SMSC911x NIC: 3530/Overo and 3630/Zoom3.
Reported-by: Tony Lindgren <tony@atomide.com>
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Adds support for boards which have an STMPE GPIO device without the
interrupt pin connected. This means that no interrupt can be received
but the GPIO pins can still be driven and read.
Cc: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Tested-by: Michel Jaouen <michel.jaouen@stericsson.com>
Signed-off-by: Chris Blair <chris.blair@stericsson.com>
Acked-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
The driver is still relying on internal OMAP IRQ defines that
are not relevant anymore if OMAP is built with SPARSE_IRQ.
Replace the defines with the proper IRQ base number.
Clean some comment style issue.
Remove some hidden and ugly cpu_class_is_omap1() inside the
gpio header.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Tested-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Adapt the GPIO driver to retrieve information from a DT file.
Allocate the irq_base dynamically and rename bank->virtual_irq_start
to bank->irq_base.
Change irq_base type to int instead of u16 to match irq_alloc_descs
output.
Add documentation for GPIO properties specific to OMAP.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Acked-by: Rob Herring <rob.herring@calxeda.com>
Replace the regular kzalloc and ioremap with the devm_ equivalent
to simplify error handling.
Add the missing devm_request_mem_region to reserve the region used
by the driver.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Tarun Kanti DebBarma <tarun.kanti@ti.com>
The driver does not need anymore any id to identify the GPIO instance.
Remove every occurence of the bank->id inside the driver.
Remove two trailing spaces.
Add a dev variable for better readability in probe.
Remove unused variable bank->pbase.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Acked-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
I've seen users getting very confused by the WARN_ON()s for can_sleep
GPIOs in the atomic-safe paths, the discoverability of the non-atomic
version of the API seems to be hampered by the fact that it's defined
in a header file not the .c file where the warnings are.
Add a couple of comments next to the warnings to help people on their
way.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Adding support for the open source gpio on which client
can specify the open source property through GPIO flag
GPIOF_OPEN_SOURCE at the time of gpio request.
The open source pins are normally pulled low and it
cannot be driven to output with value of 0 and so
when client request for setting the pin to LOW, the
gpio will be set to input direction to make pin in tristate
and hence PULL-DOWN on pins will make the state to LOW.
The open source pin can be driven to HIGH by setting output
with value of 1.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Adding support for the open drain gpio on which client
can specify the open drain property through GPIO flag
GPIOF_OPEN_DRAIN at the time of gpio request.
The open drain pins are normally pulled high and it
cannot be driven to output with value of 1 and so
when client request for setting the pin to HIGH, the
gpio will be set to input direction to make pin in tristate
and hence PULL-UP on pins will make the state to HIGH.
The open drain pin can be driven to LOW by setting output
with value of 0.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Reviwed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tegra SoC driver support.
Some device tree conversions, some new drivers. and a fix for an issue
introduced in Grant Likely's irq_domain conversion in his tree. Because
of that, this branch depends on his branch to build (but not to merge):
git://git.secretlab.ca/git/linux-2.6.git irqdomain/next
* tag 'tegra-soc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/olof/tegra: (34 commits)
ARM: tegra: uncompress.h: Don't depend on kernel headers
gpio: tegra: Fix build issue due to irq_domain rework.
ARM: tegra: Remove duplicate PMU interrupt inversion code
ARM: tegra: Add a simple PMC driver
ARM: tegra: dma: not required to move requestor when stopping.
ARM: tegra: Fix EMC pdata initialization from registers
gpio: tegra: Parameterize the number of banks
gpio: tegra: Dynamically allocate IRQ base, and support DT
ARM: tegra: Remove use of TEGRA_GPIO_TO_IRQ
ARM: tegra: Pass uncompress.h UART selection to DEBUG_LL
ARM: tegra: uncompress.h: Choose a UART at runtime
ARM: tegra: uncompress.h: Store UART address in a variable
ARM: tegra: Introduce define DEBUG_UART_SHIFT
ARM: tegra: Support Tegra30 in decompressor UART setup
ARM: tegra: Pause DMA when reading transfer count
ARM: tegra: emc: device tree support
ARM: tegra: emc: convert tegra2_emc to a platform driver
ARM: tegra: fuse: add bct strapping reading
ARM: tegra: fuse: add functions to access chip revision
ARM: tegra: fuse: use apbio dma for register access
...
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Conflicts:
arch/arm/mach-omap1/gpio16xx.c
drivers/gpio/gpio-omap.c
Merge in the runtime-pm-cleanup branch from the gpio tree into
next/cleanup, this resolves a nonobvious merge conflict between
the two branches. Both branches move parts of the gpio-omap
driver into platform code, this takes the superset of both
changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Commit 7da5a66 "irq_domain: Remove 'new' irq_domain in favour of the
ppc one" changed the set of available irq domain APIs. Update the Tegra
GPIO driver to account for those changes, to solve a build break.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This way we can remove omap_read/write call from the GPIO driver
and remove include to linux/io.h.
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Tony Lindgren <tony@atomide.com>
pl061 uses same routines for suspend/freeze/poweroff and resume/thaw/restore.
We are only saving and restoring register values on these routines.
During hibernation, in freeze() we take a snapshot of gpio registers. In thaw()
we don't actually need to restore these registers, as power was never shut down
till now. Similarly, in poweroff() we don't need to take snapshot of these
registers again, as it was done during freeze() and by now the image is already
saved on disk.
This patch passes poweroff() and thaw() routines as NULL to avoid this extra
work done.
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch converts a number of the powerpc drivers to use the common library
of irq_domain xlate functions, dropping a bunch of lines in the process.
v5: - Remove tsi108 changes from patch
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Each revmap type has different arguments for setting up the revmap.
This patch splits up the generator functions so that each revmap type
can do its own setup and the user doesn't need to keep track of how
each revmap type handles the arguments.
This patch also adds a host_data argument to the generators. There are
cases where the host_data pointer will be needed before the function returns.
ie. the legacy map calls the .map callback for each irq before returning.
v2: - Add void *host_data argument to irq_domain_add_*() functions
- fixed failure to compile
- Moved IRQ_DOMAIN_MAP_* defines into irqdomain.c
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
This patch drops the powerpc-specific irq_host structures and uses the common
irq_domain strucutres defined in linux/irqdomain.h. It also fixes all
the users to use the new structure names.
Renaming irq_host to irq_domain has been discussed for a long time, and this
patch is a step in the process of generalizing the powerpc virq code to be
usable by all architecture.
An astute reader will notice that this patch actually removes the irq_host
structure instead of renaming it. This is because the irq_domain structure
already exists in include/linux/irqdomain.h and has the needed data members.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Milton Miller <miltonm@bga.com>
Tested-by: Olof Johansson <olof@lixom.net>
Tegra20's GPIO controller has 7 banks, and Tegra30's controller has 8
banks. Allow the number of banks to be configured at run-time by the
device tree.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
Enhance the driver to dynamically allocate the base IRQ number, and
create an IRQ domain for itself. The use of an IRQ domain ensures that
any device tree node interrupts properties are correctly parsed.
Describe interrupt-related properties in the device tree binding docs,
and the contents of "child" node interrupts property.
Update tegra*.dtsi to specify the required interrupt-related properties.
Finally, remove the definition of TEGRA_GPIO_TO_IRQ; this macro no longer
gives correct results since the IRQ numbers for GPIOs are dynamically
allocated.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Olof Johansson <olof@lixom.net>
GPIO IP revisions such as those used in OMAP4 have a set_dataout
while the previous revisions used a single dataout register.
Depending on what is available restore the dataout settings
to the right register.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Setup the dataout register before restoring OE. This is to make
sure that we have valid data in dataout register which would be
made available in output pins as soon as OE is enabled. Else,
there is risk of unknown data getting out into gpio pins.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Setup the interrupt enable registers only after we have configured the
required edge and required configurations, not before, to prevent
spurious events as part of restore routine.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
GPIO debounce registers need to be saved and restored for proper functioning
of driver.
Signed-off-by: Nishanth Menon <nm@ti.com>
tarun.kanti@ti.com: Debounce context save is moved to _set_gpio_debounce()
as part of dynamic context save to remove overhead.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Context is now saved dynamically in respective functions whenever and
whichever registers are modified. This avoid overhead of saving all
registers context in the runtime suspend callback.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Enable debounce clock before writing/reading debounce registers.
Disable the clock at the end so that it is synchronized with the
pm_runtime_get/put_sync calls.
Enable debounce clock per module. This call is mandatory because
in omap_gpio_request() when *_runtime_get_sync() is called,
_gpio_dbck_enable() within runtime callbck fails to turn on dbck
because dbck_enable_mask used within _gpio_dbck_enable() is still
not initialized at that point. Therefore we have to enable dbck here.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The dbck_enable_mask indicates which all GPIOs within a bank have debounce
enabled and dbck is enabled/disabled based upon this. But there is no
mechanism to track the dbck state. In order to manage the dbck state we need
additional flag and logic so that turning off/on dbck is synchronized with
pm_runtime_put/get_sync calls.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Since *_prepare_for_idle() and *_resume_after_idle() are called
with interrupts disabled they should be kept as simple as possible.
So, moving most of the stuff to *_runtime_suspend/resume() callbacks.
To avoid invalid context restore happening in *_runtime_resume()
callback as a result of *_get_sync() call in *_gpio_probe(), update
bank->context_loss_count. This would make context restore condition
check false in the callback and skip restore until further
initialization take place. The workaround_enabled static variable
is now a member of struct gpio_bank.
Unlike most GPIO registers the OE has 0xffffffff as the default value.
To make sure invalid context is not restored, updating the OE context
with default value.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
There is no need to operate on all the banks every time the function is called.
Just operate on the current bank passed by the framework.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Call runtime pm APIs pm_runtime_get_sync() and pm_runtime_put()
for enabling/disabling clocks appropriately. Remove syscore_ops and
instead use SET_RUNTIME_PM_OPS macro.
There is no more need to call omap_device_disable_idle_on_suspend
since driver is PM runtime adapted now.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The only bank->type (method) used in the OMAP GPIO driver is MPUIO type as they
need to be handled separately. Identify the same using a flag and remove all
METHOD_* macros.
mpuio_init() function is defined under #ifdefs. It is required only in case
of MPUIO bank type and only when PM operations are supported by it.
This is applicable only in case of OMAP16xx SoC's MPUIO GPIO bank type.
For all the other cases it is a dummy function. Hence clean up the same
and remove all the OMAP SoC specific #ifdefs.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove un-necessary bit masking. Since the register are 4 byte aligned
and readl would work as is. The 'enabled' mask is already taking care
to mask for bank width.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Use regs->pinctrl field instead of using the macro OMAP1510_GPIO_PIN_CONTROL
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
With register offsets now defined for respective OMAP versions we can get rid
of cpu_class_* checks. This function now has common initialization code for
all OMAP versions. Initialization specific to OMAP16xx has been moved within
omap16xx_gpio_init().
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Getting rid of ifdefs within the function by adding register offset intctrl
and associating OMAPXXXX_GPIO_INT_CONTROL in respective SoC specific files.
Also, use wkup_status register consistently instead of referring to wakeup
clear and wakeup set register offsets. Get rid of cpu_is_xxxx checks in
set_gpio_trigger() using irqctrl.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
It is not required to use hard-coded offsets any more in context save and
restore functions and instead use the generic offsets which have been correctly
initialized during device registration.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
By adding level and edge detection register offsets and then initializing them
correctly according to OMAP versions during device registrations we can now remove
lot of revision checks in these functions.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Wakeup enable register offset initialized according to OMAP versions
during device registration. Use this to avoid version checks.
Starting with OMAP4, legacy registers should not be used in combination
with the updated regsiters. Use wkup_en register consistently for
all SoCs wherever applicable.
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Remove cpu-is checks while enabling/disabling OMAP GPIO module during a gpio
request/free.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Non-wakeup GPIOs are available only in OMAP2. Avoid cpu_is checks by making
non_wakeup_gpios as part of pdata.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Modify omap_gpio_prepare_for_idle() & omap_gpio_resume_after_idle() functions
to handle save context & restore context respectively in the OMAP GPIO driver
itself instead of calling these functions from pm specific files.
For this, in gpio_prepare_for_idle(), call *_get_context_loss_count() and in
gpio_resume_after_idle() call it again. If the count is different, do restore
context.
Signed-off-by: Charulatha V <charu@ti.com>
Signed-off-by: Tarun Kanti DebBarma <tarun.kanti@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Currently gpio_context array used to save gpio bank's context, is used only for
OMAP3 architecture. Move gpio_context as part of gpio_bank structure so that it
can be specific to each gpio bank and can be used for any OMAP architecture
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
In omap3, save/restore context is implemented for GPIO banks 2-6 as GPIO bank1
is in wakeup domain. Instead of identifying bank's power domain by bank id,
use 'loses_context' flag which is filled by pwrdm_can_ever_lose_context()
during dev_init.
For getting the powerdomain pointer, omap_hwmod_get_pwrdm() is used.
omap_device_get_pwrdm() could not be used as the pwrdm information needs to be
filled in pdata, whereas omap_device_get_pwrdm() could be used only after
omap_device_build() call.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The gpio_bank_count is the count of number of GPIO devices in a SoC. Remove this
dependency from the driver by using list. Also remove the dependency on array of
pointers to gpio_bank struct of all GPIO devices.
Signed-off-by: Charulatha V <charu@ti.com>
Reviewed-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Reviewed-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The device tps65910/tps65911 supports the sleep
functionality in some of gpios. If gpio is configured
in output mode and sleep is enabled then during device
sleep state, the output of gpio becomes LOW regardless
of non-sleep output value.
Such gpio can be used to control regulator switch such
that output of regulator is off in device sleep state.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Sodaville has GPIO controller behind the PCI bus. To my suprissed it is
not the same as on PXA.
The interrupt & gpio chip can be referenced from the device tree like
from any other driver. Unfortunately the driver which uses the gpio
interrupt has to use irq_of_parse_and_map() instead of
platform_get_irq(). The problem is that the platform device (which is
created from the device tree) is most likely created before the
interrupt chip is registered and therefore irq_of_parse_and_map() fails.
In theory the driver works as module. In reality most of the irq
functions are not exported to modules and it is possible that _this_
module is unloaded while the provided irqs are still in use.
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
[torbenh@linutronix.de: make it work after the irq namespace cleanup,
add some device tree entries.]
Signed-off-by: Torben Hohn <torbenh@linutronix.de>
[bigeasy@linutronix.de: convert to generic irq & gpio chip]
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
[grant.likely@secretlab.ca: depend on x86 to avoid irq_domain breakage]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This bug was introduced by commit 54be5663
"gpio-ml-ioh: Support interrupt function" which adds a spinlock to struct
ioh_gpio but never init the spinlock.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This bug was introduced by commit d568a681
"gpio-pch: add spinlock in suspend/resume processing"
which adds a spinlock to struct pch_gpio but never init the spinlock.
Reported-by: Tomoya MORINAGA <tomoya.rohm@gmail.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit 15c9a0acc3 (of: create of_phandle_args to simplify return of phandle
parsing data) modifies the parameter list of of_xlate function pointer declaration
in gpio_chip. Adapt the gpio specifier translate function for this change.
Reported-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Tested-by: Karol Lewandowski <k.lewandowsk@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
we only use the gpio function of mc9s08dz60 mcu chip, so just
add the gpio driver, as this mcu will never be used in other board.
Signed-off-by: Wu Guoxing <b39297@freescale.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In preparation to make mach/irqs.h optional and remove from asm/irq.h,
directly include mach/irq.h to get MMP_GPIO_TO_IRQ and PXA_GPIO_TO_IRQ.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
One of the GPIO names in drivers/gpio/gpio-lpc32xx.c
was bad. Renaming gpi000 -> gpio00
Signed-off-by: Roland Stigge <stigge@antcom.de>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Using the correct gpio offset for setting the initial value
of gpio when setting output direction.
Signed-off-by: Laxman Dewangan <ldewangan@nvidia.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This driver does an unconditional read of io space during module init which
causes a bad dereference on ARM. It looks to me like this is an x86 only
drivers, so restrict it to only compile on x86.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Denis Turischev <denis@compulab.co.il>
The __iomem annotation is to be used together with pointers used
in iowrite32() but not for pointers returned by kzalloc().
For more details see [1] and [2].
This patch will remove the following sparse warning (i.e. when
copiling with "make C=1"):
* warning: incorrect type in assignment (different address spaces)
References:
[1] A new I/O memory access mechanism (Sep 15, 2004)
http://lwn.net/Articles/102232/
[2] Being more anal about iospace accesses (Sep 15, 2004)
http://lwn.net/Articles/102240/
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch will remove the following sparse warning ("make C=1"):
* warning: Using plain integer as NULL pointer
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The __iomem annotation is to be used together with pointers used
as iowrite32() parameter. For more details see [1] and [2].
This patch will remove the following sparse warnings ("make C=1"):
* warning: incorrect type in assignment (different address spaces)
* warning: incorrect type in argument 1 (different address spaces)
* warning: incorrect type in argument 2 (different address spaces)
References:
[1] A new I/O memory access mechanism (Sep 15, 2004)
http://lwn.net/Articles/102232/
[2] Being more anal about iospace accesses (Sep 15, 2004)
http://lwn.net/Articles/102240/
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch will remove the following sparse warning ("make C=1"):
* warning: Using plain integer as NULL pointer
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The existing gpio_to_irq() implementation on sa1100 only translates
validly for internal GPIOs. Since this sub-arch enables GPIOLIB
support, this results in buggy translations for non-internal GPIOs.
Get rid of the private gpio_to_irq() implementation, replacing it
with the .to_irq method in the sa1100 gpio chip instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (31 commits)
pinctrl: remove unnecessary max pin number
pinctrl: correct a offset while enumerating pins
pinctrl: some typo fixes
pinctrl: rename U300 and SIRF pin controllers
pinctrl: pass name instead of device to pin_config_*
pinctrl: add "struct seq_file;" to pinconf.h
pinctrl: conjure names for unnamed pins
pinctrl: add a group-specific hog macro
pinctrl: don't create a device for each pin controller
arm/u300: don't use PINMUX_MAP_PRIMARY*
pinctrl: implement PINMUX_MAP_SYS_HOG
pinctrl: add a pin config interface
pinctrl/coh901: driver to request its pins
pinctrl: u300-pinmux: register proper GPIO ranges
pinctrl: move the U300 GPIO driver to pinctrl
ARM: u300: localize GPIO assignments
pinctrl: make it possible to add multiple maps
pinctrl: make a copy of pinmux map
pinctrl: GPIO direction support for muxing
pinctrl: print pin range in GPIO range debugs
...
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=vPhu
-----END PGP SIGNATURE-----
Merge tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Driver specific changes
Again, a lot of platforms have changes in here: pxa, samsung, omap,
at91, imx, ...
* tag 'drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
ARM: sa1100: clean up of the clock support
ARM: pxa: add dummy clock for sa1100-rtc
RTC: sa1100: support sa1100, pxa and mmp soc families
RTC: sa1100: remove redundant code of setting alarm
RTC: sa1100: Clean out ost register
Input: zylonite-wm97xx - replace IRQ_GPIO() with gpio_to_irq()
pcmcia: pxa: replace IRQ_GPIO() with gpio_to_irq()
ARM: EXYNOS: Modified files for SPI consolidation work
ARM: S5P64X0: Enable SDHCI support
ARM: S5P64X0: Add lookup of sdhci-s3c clocks using generic names
ARM: S5P64X0: Add HSMMC setup for host Controller
ARM: EXYNOS: Add USB OHCI support to ORIGEN board
USB: Add Samsung Exynos OHCI diver
ARM: EXYNOS: Add USB OHCI support to SMDKV310 board
ARM: EXYNOS: Add USB OHCI device
net: macb: fix build break with !CONFIG_OF
i2c: tegra: Support DVC controller in device tree
i2c: tegra: Add __devinit/exit to probe/remove
net/at91_ether: use gpio_is_valid for phy IRQ line
ARM: at91/net: add macb ethernet controller in 9g45/9g20 DT
...
Both platforms had some initial device tree support, but this adds
much more to actually make it usable.
This is where the really nasty conflicts in the samsung platform
start, due to some files getting moved around and combined in the
'restart' branch that has already gone into mainline through
Russell's tree.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=XY2N
-----END PGP SIGNATURE-----
Merge tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Device tree conversions for samsung and tegra
Both platforms had some initial device tree support, but this adds
much more to actually make it usable.
* tag 'dt' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (45 commits)
ARM: dts: Add intial dts file for EXYNOS4210 SoC, SMDKV310 and ORIGEN
ARM: EXYNOS: Add Exynos4 device tree enabled board file
rtc: rtc-s3c: Add device tree support
input: samsung-keypad: Add device tree support
ARM: S5PV210: Modify platform data for pl330 driver
ARM: S5PC100: Modify platform data for pl330 driver
ARM: S5P64x0: Modify platform data for pl330 driver
ARM: EXYNOS: Add a alias for pdma clocks
ARM: EXYNOS: Limit usage of pl330 device instance to non-dt build
ARM: SAMSUNG: Add device tree support for pl330 dma engine wrappers
DMA: PL330: Add device tree support
ARM: EXYNOS: Modify platform data for pl330 driver
DMA: PL330: Infer transfer direction from transfer request instead of platform data
DMA: PL330: move filter function into driver
serial: samsung: Fix build for non-Exynos4210 devices
serial: samsung: add device tree support
serial: samsung: merge probe() function from all SoC specific extensions
serial: samsung: merge all SoC specific port reset functions
ARM: SAMSUNG: register uart clocks to clock lookup list
serial: samsung: remove all uses of get_clksrc and set_clksrc
...
Fix up fairly trivial conflicts in arch/arm/mach-s3c2440/clock.c and
drivers/tty/serial/Kconfig both due to just adding code close to
changes.
STMPE801 is a GPIO expander. GPIO registers for 801 are slightly different from other
variants. This patch adds support for STMPE801 in stmpe gpio driver.
Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com>
Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regmap: (36 commits)
mfd: Clearing events requires event registers to be writable for da9052-core
mfd: Fix annotations in da9052-core
gpiolib: Mark da9052 driver broken
mfd: Declare da9052_regmap_config for the bus drivers
MFD: DA9052/53 MFD core module add SPI support v2
MFD: DA9052/53 MFD core module
regmap: Add irq_base accessor to regmap_irq
regmap: Allow drivers to reinitialise the register cache at runtime
regmap: Add trace event for successful cache reads
regmap: Allow regmap_update_bits() users to detect changes
regmap: Report if we actually handled an interrupt in regmap-irq
regmap: Fix rbtreee build when not using debugfs
regmap: Provide debugfs dump of the rbtree cache data
regmap: Do debugfs init before cache init
regmap: Suppress noop writes in regmap_update_bits()
regmap: Remove indexed cache type
regmap: Drop check whether a register is readable in regcache_read
regmap: Properly round cache_word_size
regmap: Add support for 10/14 register formating
regmap: Try cached read before checking if a hardware read is possible
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (53 commits)
Kconfig: acpi: Fix typo in comment.
misc latin1 to utf8 conversions
devres: Fix a typo in devm_kfree comment
btrfs: free-space-cache.c: remove extra semicolon.
fat: Spelling s/obsolate/obsolete/g
SCSI, pmcraid: Fix spelling error in a pmcraid_err() call
tools/power turbostat: update fields in manpage
mac80211: drop spelling fix
types.h: fix comment spelling for 'architectures'
typo fixes: aera -> area, exntension -> extension
devices.txt: Fix typo of 'VMware'.
sis900: Fix enum typo 'sis900_rx_bufer_status'
decompress_bunzip2: remove invalid vi modeline
treewide: Fix comment and string typo 'bufer'
hyper-v: Update MAINTAINERS
treewide: Fix typos in various parts of the kernel, and fix some comments.
clockevents: drop unknown Kconfig symbol GENERIC_CLOCKEVENTS_MIGR
gpio: Kconfig: drop unknown symbol 'CS5535_GPIO'
leds: Kconfig: Fix typo 'D2NET_V2'
sound: Kconfig: drop unknown symbol ARCH_CLPS7500
...
Fix up trivial conflicts in arch/powerpc/platforms/40x/Kconfig (some new
kconfig additions, close to removed commented-out old ones)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=9ugo
-----END PGP SIGNATURE-----
Merge tag 'gpio-for-linus' of git://git.secretlab.ca/git/linux-2.6
Changes queued in gpio/next for the start of the 3.3 merge window
* tag 'gpio-for-linus-20120104' of git://git.secretlab.ca/git/linux-2.6:
gpio: Add decode of WM8994 GPIO configuration
gpio: Convert GPIO drivers to module_platform_driver
gpio: Fix typo in comment in Samsung driver
gpio: Explicitly index samsung_gpio_cfgs
gpio: Add Linus Walleij as gpio co-maintainer
of: Add device tree selftests
of: create of_phandle_args to simplify return of phandle parsing data
gpio/powerpc: Eliminate duplication of of_get_named_gpio_flags()
gpio/microblaze: Eliminate duplication of of_get_named_gpio_flags()
gpiolib: output basic details and consolidate gpio device drivers
pch_gpio: Change company name OKI SEMICONDUCTOR to LAPIS Semiconductor
pch_gpio: Support new device LAPIS Semiconductor ML7831 IOH
spi/pl022: make the chip deselect handling thread safe
spi/pl022: add support for pm_runtime autosuspend
spi/pl022: disable the PL022 block when unused
spi/pl022: move device disable to workqueue thread
spi/pl022: skip default configuration before suspending
spi/pl022: fix build warnings
spi/pl022: only enable RX interrupts when TX is complete
* 'driver-core-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (73 commits)
arm: fix up some samsung merge sysdev conversion problems
firmware: Fix an oops on reading fw_priv->fw in sysfs loading file
Drivers:hv: Fix a bug in vmbus_driver_unregister()
driver core: remove __must_check from device_create_file
debugfs: add missing #ifdef HAS_IOMEM
arm: time.h: remove device.h #include
driver-core: remove sysdev.h usage.
clockevents: remove sysdev.h
arm: convert sysdev_class to a regular subsystem
arm: leds: convert sysdev_class to a regular subsystem
kobject: remove kset_find_obj_hinted()
m86k: gpio - convert sysdev_class to a regular subsystem
mips: txx9_sram - convert sysdev_class to a regular subsystem
mips: 7segled - convert sysdev_class to a regular subsystem
sh: dma - convert sysdev_class to a regular subsystem
sh: intc - convert sysdev_class to a regular subsystem
power: suspend - convert sysdev_class to a regular subsystem
power: qe_ic - convert sysdev_class to a regular subsystem
power: cmm - convert sysdev_class to a regular subsystem
s390: time - convert sysdev_class to a regular subsystem
...
Fix up conflicts with 'struct sysdev' removal from various platform
drivers that got changed:
- arch/arm/mach-exynos/cpu.c
- arch/arm/mach-exynos/irq-eint.c
- arch/arm/mach-s3c64xx/common.c
- arch/arm/mach-s3c64xx/cpu.c
- arch/arm/mach-s5p64x0/cpu.c
- arch/arm/mach-s5pv210/common.c
- arch/arm/plat-samsung/include/plat/cpu.h
- arch/powerpc/kernel/sysfs.c
and fix up cpu_is_hotpluggable() as per Greg in include/linux/cpu.h
* 'amba-modalias' of git://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
sound: aaci: Enable module alias autogeneration for AMBA drivers
watchdog: sp805: Enable module alias autogeneration for AMBA drivers
fbdev: amba: Enable module alias autogeneration for AMBA drivers
serial: pl011: Enable module alias autogeneration for AMBA drivers
serial: pl010: Enable module alias autogeneration for AMBA drivers
spi: pl022: Enable module alias autogeneration for AMBA drivers
rtc: pl031: Enable module alias autogeneration for AMBA drivers
rtc: pl030: Enable module alias autogeneration for AMBA drivers
mmc: mmci: Enable module alias autogeneration for AMBA drivers
input: ambakmi: Enable module alias autogeneration for AMBA drivers
gpio: pl061: Enable module alias autogeneration for AMBA drivers
dmaengine: pl330: Enable module alias autogeneration for AMBA drivers
dmaengine: pl08x: Enable module alias autogeneration for AMBA drivers
hwrng: nomadik: Enable module alias autogeneration for AMBA drivers
ARM: amba: Auto-generate AMBA driver module aliases during modpost
ARM: amba: Move definition of struct amba_id to mod_devicetable.h
This resolves the conflict in the arch/arm/mach-s3c64xx/s3c6400.c file,
and it fixes the build error in the arch/x86/kernel/microcode_core.c
file, that the merge did not catch.
The microcode_core.c patch was provided by Stephen Rothwell
<sfr@canb.auug.org.au> who was invaluable in the merge issues involved
with the large sysdev removal process in the driver-core tree.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Drivers should not have a dependency on NR_IRQS. Doing so may break with
SPARSE_IRQ enabled. As there are no in kernel users of the pl061 which
have multiple instances with their interrupts combined to a single parent
interrupt, remove this functionality. If this capability is needed later,
it could be supported more cleanly by just using a devicetree property.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Reviewed-by: Viresh Kumar <viresh.kumar@st.com>
Cc: Rajeev Kumar <rajeev-dlh.kumar@st.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Convert the pl061 irq_chip code to use the generic irq chip code.
This has the side effect of using 32-bit accesses rather than 8-bit
accesses to interrupt registers. The h/w TRM and testing seem to indicate
this is fine.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
This patch adds 2 functions that allow managed devices to request GPIOs.
These GPIOs will then be managed by drivers/base/devres.c.
Signed-off-by: John Crispin <blogic@openwrt.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We don't want drivers using NO_IRQ, so remove its use. For now, 0 or
-1 means no irq until platforms are converted to use 0.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.ml.walleij@gmail.com>
Use chained_irq_enter/exit helper functions instead of direct pointer
accesses. This is needed for generic irq chip conversion.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Linus Walleij <linus.ml.walleij@gmail.com>
This patch adds the suspend and resume operations in the driver. The patch
ensures the data save and restore for the device registers during the
suspend and resume operations respectively.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@st.com>
Acked-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This driver will be converted to a dual GPIO + pinctrl driver
since it supports biasing and driving control options. Hopefully
it can serve as an example.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reimplement a call to devm_request_mem_region followed by a call to ioremap
or ioremap_nocache by a call to devm_request_and_ioremap.
The semantic patch that makes this transformation is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@nm@
expression myname;
identifier i;
@@
struct platform_driver i = { .driver = { .name = myname } };
@@
expression dev,res,size;
expression nm.myname;
@@
-if (!devm_request_mem_region(dev, res->start, size,
- \(res->name\|dev_name(dev)\|myname\))) {
- ...
- return ...;
-}
... when != res->start
(
-devm_ioremap(dev,res->start,size)
+devm_request_and_ioremap(dev,res)
|
-devm_ioremap_nocache(dev,res->start,size)
+devm_request_and_ioremap(dev,res)
)
... when any
when != res->start
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
For the human reader.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Where appropriate factor out some boilerplate code for platform device
registration into module_platform_driver. Drivers that don't use the
standard module_init initcall haven't been converted.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Make it easier to follow the by number references into samsung_gpio_cfgs
by putting the indexes into the code initialising the array, improving
readability a bit. Ideally we wouldn't be using magic array indexes at all
but this is easier than coming up with a better way.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Kukjin Kim <kgene.kim@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
As gpio chips get registered, a device tree node which represents the
gpio chip is searched and attached to it. A translate function is also
provided to convert the gpio specifier into actual platform settings
for pin function selection, pull up/down and driver strength settings.
Signed-off-by: Thomas Abraham <thomas.abraham@linaro.org>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
[kgene.kim@samsung.com: fixed build error]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The sysdev.h file should not be needed by any in-kernel code, so remove
the .h file from these random files that seem to still want to include
it.
The sysdev code will be going away soon, so this include needs to be
removed no matter what.
Cc: Jiandong Zheng <jdzheng@broadcom.com>
Cc: Scott Branden <sbranden@broadcom.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Kukjin Kim <kgene.kim@samsung.com>
Cc: David Brown <davidb@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Wan ZongShun <mcuos.com@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@gmail.com>
Cc: Hans-Christian Egtvedt <egtvedt@samfundet.no>
Cc: Guan Xuetao <gxt@mprc.pku.edu.cn>
Cc: "Venkatesh Pallipadi
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
This patch is functionally tested on Samsung SMDKV6410.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David Dajun Chen <dchen@diasemi.com>
Signed-off-by: Ashish Jangam <ashish.jangam@kpitcummins.com>
[grant.likely: don't create an unnecessary header file]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add a 5121-custom reject if an input-only pin is requested to be output
(see 18.3.1.1 in the refman). Also, rewrite mach-specific quirk setup to
consume less lines which scales better.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
[grant.likely: Fixed build error]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
These hooks will be needed by the general disabl/enable_irq();
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
GPIO's irq action's dev_id is set to the first struct ioh_gpio chip,
so when loop checking the 8 chips, the "chip" should be changed
according.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
In adding DT binding support, the check for NULL platform_data got added
back in inadvertently, so remove it.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
A large chunk of qe_pin_request() is unnecessarily cut-and-paste
directly from of_get_named_gpio_flags(). This patch cuts out the
duplicate code and replaces it with a call to of_get_gpio().
v2: fixed compile error due to missing gpio_to_chip()
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Kumar Gala <galak@kernel.crashing.org>
This patch adds a kernel message, containing GPIO range and device
name on successful device registration, and removes duplicate messages from the following drivers:
* gpio-adp5588
* gpio-bt8xx
* gpio-cs5535
* gpio-janz-ttl
* gpio-nomadik
* gpio-pcf857x
* gpio-xilinx
* drivers/of/gpio.c
Signed-off-by: Hartmut Knaack <knaack.h@gmx.de>
[grant.likely@secretlab.ca: squashed 2 patches together]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
On October 1 in 2011,
OKI SEMICONDUCTOR Co., Ltd. changed the company name in to LAPIS Semiconductor Co., Ltd.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
ML7831 is companion chip for Intel Atom E6xx series.
Signed-off-by: Tomoya MORINAGA <tomoya-linux@dsn.lapis-semi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
I screwed up by compiling that driver for the machine rather
than the arch. Correcting this fixes the build error.
Cc: Grant Likely <grant.likely@secretlab.ca>
Reported-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit af0c25c487 ("staging: remove obsoleted CS5535/CS5536 GPIO
driver") dropped CS5535_GPIO. So this last reference to CS5535_GPIO has
been an (inconsequential) nop since v3.1. Drop it too.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
It's not used outside of the driver so doesn't need to be exported, and
sparse notices this and complains about it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'gpio/merge' of git://git.secretlab.ca/git/linux-2.6:
gpio: pca953x: propagate the errno from the chip_init functions
gpio: pca953x: remove unneeded check for chip type
gpio/omap: check return value from irq_alloc_generic_chip
gpio/omap: replace MOD_REG_BIT macro with static inline
Support clk in gpio driver. There's no gpio clock in PXA25x and PXA27x.
So use dummy clk instead. And move the gpio edge initialization into
gpio driver for arch-mmp.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Use cpuid to recognize the gpio number and type. CPU_PXA26x is the
special case since we can't identify it by cpuid.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Avoid to define gpio_to_irq() and irq_to_gpio() for potential name
confliction since multiple architecture will be built together.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Linus Walleij