The current 110ms expiry time is not long enough for the internal abort
task.
The reason is that the internal abort task could be blocked in HW if the HW
is retrying to set up link. The internal abort task will be executed only
when the retry process finished.
The maximum time is 5s for the retry of setting up link. So, the timer
expire should be more than 5s. This patch increases it from 110ms to 6s.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
It is not right to set the register PROG_PHY_LINK_RATE while PHY is still
enabled. So if we want to change PHY linkrate, we need to disable PHY before
setting the register PROG_PHY_LINK_RATE, and then start-up PHY. This patch
is to fix this issue.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In sysfs, there are two files about minimum linkrate, and also two files for
maximum linkrate. Take maximum linkrate example, maximum_linkrate_hw is
read-only and indicated by the register HARD_PHY_LINKRATE, and
maximum_linkrate is read-write and corresponding to the register
PROG_PHY_LINK_RATE.
But in the function phy_up_v*_hw(), we get *_linkrate value from
HARD_PHY_LINKRATE. It is not right. This patch is to fix this issue.
Unreferenced PHY-interrupt enum is also removed for v3 hw.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The register SAS_PHY_CTRL is configured according to signal quality. The
signal quality is calculated by signal attenuation of hardware physical
link. It may be different for different PCB layout.
So, in order to give better support to new board, this patch add support to
reading the devicetree property, "hisilicon,signal-attenuation". Of course,
we still keep an default value in driver to adapt old board.
Signed-off-by: Xiaofei Tan <tanxiaofei@huawei.com>
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The SCSI PRE-FETCH (10 or 16) command is present both on hard disks
and some SSDs. It is useful when the address of the next block(s) to
be read is known but it is not following the LBA of the current READ
(so read-ahead won't help). It returns two "good" SCSI Status values.
If the requested blocks have fitted (or will most likely fit (when
the IMMED bit is set)) into the disk's cache, it returns CONDITION
MET. If it didn't (or will not) fit then it returns GOOD status.
The goal of this patch is to stop the SCSI subsystem treating the
CONDITION MET SCSI status as an error. The current state makes the
PRE-FETCH command effectively unusable via pass-throughs.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated Copyright in files updated as part of 12.0.0.1
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 12.0.0.1
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver fails to allocate command buffers in the routine
lpfc_new_scsi_buf_s4
There is an inconsistency between lpfc_mem_alloc(), where the
phba->lpfc_sg_dma_buf_pool is created, and lpfc_new_scsi_buf_s4(),
when we allocate a buffer from the pool and check the alignment. The
alignment should be on a page boundary, based on LPFC_SLI3_BG_ENABLED in
sli3_options, for both cases.
Fix by explicitly tracking sli4 vs sli3 and BG options. The result is that
phba->cfg_sg_dma_buf_size is now set correctly for SLI-4.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
POST_SGL_PAGES mailbox command failed with status (timeout).
wait_event_interruptible_timeout when called from mailbox wait interface,
gets interrupted, and will randomly fail. Behavior seems very specific to 1
particular server type.
Fix by changing from wait_event_interruptible_timeout to
wait_for_completion_timeout.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When a port is configured for NVME and SCSI Initiator support and it probes
a target supporting both SCSI and NVME, NVME devices are discovered, but
SCSI devices are not.
The nlp_fc4_type for all NPorts should be cleared on Link Up or just before
GID_FTs get issued, as opposed to just during GID_FT cmpl. RSCN activity as
well as Link Up can trigger GID_FT. One GID_FT may complete before the next
one is issued.
Fix by clearng nlp_fc4_type on link up and just before both GID_FTs are
issued. During port swapping, copy nlp_fc4_type to the new ndlp
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To reduce latency when initializing WQE content, created templates for the
most common wqes. This reduces the number of operations taken to set the
content. It's not a lot of speed up, but every bit helps.
This patch updates the NVME target path.
[mkp: fixed typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
To reduce latency when initializing WQE content, create templates for the
most common wqes. This reduces the number of operations taken to set the
content. It's not a lot of speed up, but every bit helps.
This patch updates the NVME initiator path.
[mkp: fixed typo]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver is very sloppy about the WQE structure passed between routines.
The base struct type is a 64byte wqe. But in many routines they typecast and
access 128byte wqes. There were a couple of cases in the past (corrected
already) where the typecasts were incorrectly done and the 64byte buffer was
accessed as a 128 byte buffer.
Clean this up by properly declaring wqe's as 128byte wqe's and removing the
typecasts. 64byte wqes are considered a subset of the 128byte wqes.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
First Burst support was not properly indicated in NVMe PRLI.
Correct the bit position and the logic to check and set first burst support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 6e8e1c14c6 ("scsi: lpfc: Add WQ Full Logic for NVME Target") fails
the static checker. Checker correctly identified a missing unlock on a
return path.
Add the unlock.
Fixes: 6e8e1c14c6 ("scsi: lpfc: Add WQ Full Logic for NVME Target")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use dma_pool_zalloc() instead of dma_pool_alloc + memset
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 7d64c39e64310 fixed regression of FCP discovery when Nport Handle
is in-use and relogin is triggered. However, during FCP and FC-NVMe
discovery this resulted into only discovering NVMe LUNs.
This patch fixes issue where FCP and FC-NVMe protocol is used on same
port where assigning FC_NO_LOOP_ID will result into discovery failure
for FCP LUNs.
Fixes: a084fd68e1 ("scsi: qla2xxx: Fix re-login for Nport Handle in use")
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When ata device doing EH, some commands still attached with tasks are
not passed to libata when abort failed or recover failed, so libata did
not handle these commands. After these commands done, sas task is freed,
but ata qc is not freed. This will cause ata qc leak and trigger a
warning like below:
WARNING: CPU: 0 PID: 28512 at drivers/ata/libata-eh.c:4037
ata_eh_finish+0xb4/0xcc
CPU: 0 PID: 28512 Comm: kworker/u32:2 Tainted: G W OE 4.14.0#1
......
Call trace:
[<ffff0000088b7bd0>] ata_eh_finish+0xb4/0xcc
[<ffff0000088b8420>] ata_do_eh+0xc4/0xd8
[<ffff0000088b8478>] ata_std_error_handler+0x44/0x8c
[<ffff0000088b8068>] ata_scsi_port_error_handler+0x480/0x694
[<ffff000008875fc4>] async_sas_ata_eh+0x4c/0x80
[<ffff0000080f6be8>] async_run_entry_fn+0x4c/0x170
[<ffff0000080ebd70>] process_one_work+0x144/0x390
[<ffff0000080ec100>] worker_thread+0x144/0x418
[<ffff0000080f2c98>] kthread+0x10c/0x138
[<ffff0000080855dc>] ret_from_fork+0x10/0x18
If ata qc leaked too many, ata tag allocation will fail and io blocked
for ever.
As suggested by Dan Williams, defer ata device commands to libata and
merge sas_eh_finish_cmd() with sas_eh_defer_cmd(). libata will handle
ata qcs correctly after this.
Signed-off-by: Jason Yan <yanaijie@huawei.com>
CC: Xiaofei Tan <tanxiaofei@huawei.com>
CC: John Garry <john.garry@huawei.com>
CC: Dan Williams <dan.j.williams@intel.com>
Reviewed-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
when mounting an ISO filesystem sometimes (very rarely)
the system hangs because of a race condition between two tasks.
PID: 6766 TASK: ffff88007b2a6dd0 CPU: 0 COMMAND: "mount"
#0 [ffff880078447ae0] __schedule at ffffffff8168d605
#1 [ffff880078447b48] schedule_preempt_disabled at ffffffff8168ed49
#2 [ffff880078447b58] __mutex_lock_slowpath at ffffffff8168c995
#3 [ffff880078447bb8] mutex_lock at ffffffff8168bdef
#4 [ffff880078447bd0] sr_block_ioctl at ffffffffa00b6818 [sr_mod]
#5 [ffff880078447c10] blkdev_ioctl at ffffffff812fea50
#6 [ffff880078447c70] ioctl_by_bdev at ffffffff8123a8b3
#7 [ffff880078447c90] isofs_fill_super at ffffffffa04fb1e1 [isofs]
#8 [ffff880078447da8] mount_bdev at ffffffff81202570
#9 [ffff880078447e18] isofs_mount at ffffffffa04f9828 [isofs]
#10 [ffff880078447e28] mount_fs at ffffffff81202d09
#11 [ffff880078447e70] vfs_kern_mount at ffffffff8121ea8f
#12 [ffff880078447ea8] do_mount at ffffffff81220fee
#13 [ffff880078447f28] sys_mount at ffffffff812218d6
#14 [ffff880078447f80] system_call_fastpath at ffffffff81698c49
RIP: 00007fd9ea914e9a RSP: 00007ffd5d9bf648 RFLAGS: 00010246
RAX: 00000000000000a5 RBX: ffffffff81698c49 RCX: 0000000000000010
RDX: 00007fd9ec2bc210 RSI: 00007fd9ec2bc290 RDI: 00007fd9ec2bcf30
RBP: 0000000000000000 R8: 0000000000000000 R9: 0000000000000010
R10: 00000000c0ed0001 R11: 0000000000000206 R12: 00007fd9ec2bc040
R13: 00007fd9eb6b2380 R14: 00007fd9ec2bc210 R15: 00007fd9ec2bcf30
ORIG_RAX: 00000000000000a5 CS: 0033 SS: 002b
This task was trying to mount the cdrom. It allocated and configured a
super_block struct and owned the write-lock for the super_block->s_umount
rwsem. While exclusively owning the s_umount lock, it called
sr_block_ioctl and waited to acquire the global sr_mutex lock.
PID: 6785 TASK: ffff880078720fb0 CPU: 0 COMMAND: "systemd-udevd"
#0 [ffff880078417898] __schedule at ffffffff8168d605
#1 [ffff880078417900] schedule at ffffffff8168dc59
#2 [ffff880078417910] rwsem_down_read_failed at ffffffff8168f605
#3 [ffff880078417980] call_rwsem_down_read_failed at ffffffff81328838
#4 [ffff8800784179d0] down_read at ffffffff8168cde0
#5 [ffff8800784179e8] get_super at ffffffff81201cc7
#6 [ffff880078417a10] __invalidate_device at ffffffff8123a8de
#7 [ffff880078417a40] flush_disk at ffffffff8123a94b
#8 [ffff880078417a88] check_disk_change at ffffffff8123ab50
#9 [ffff880078417ab0] cdrom_open at ffffffffa00a29e1 [cdrom]
#10 [ffff880078417b68] sr_block_open at ffffffffa00b6f9b [sr_mod]
#11 [ffff880078417b98] __blkdev_get at ffffffff8123ba86
#12 [ffff880078417bf0] blkdev_get at ffffffff8123bd65
#13 [ffff880078417c78] blkdev_open at ffffffff8123bf9b
#14 [ffff880078417c90] do_dentry_open at ffffffff811fc7f7
#15 [ffff880078417cd8] vfs_open at ffffffff811fc9cf
#16 [ffff880078417d00] do_last at ffffffff8120d53d
#17 [ffff880078417db0] path_openat at ffffffff8120e6b2
#18 [ffff880078417e48] do_filp_open at ffffffff8121082b
#19 [ffff880078417f18] do_sys_open at ffffffff811fdd33
#20 [ffff880078417f70] sys_open at ffffffff811fde4e
#21 [ffff880078417f80] system_call_fastpath at ffffffff81698c49
RIP: 00007f29438b0c20 RSP: 00007ffc76624b78 RFLAGS: 00010246
RAX: 0000000000000002 RBX: ffffffff81698c49 RCX: 0000000000000000
RDX: 00007f2944a5fa70 RSI: 00000000000a0800 RDI: 00007f2944a5fa70
RBP: 00007f2944a5f540 R8: 0000000000000000 R9: 0000000000000020
R10: 00007f2943614c40 R11: 0000000000000246 R12: ffffffff811fde4e
R13: ffff880078417f78 R14: 000000000000000c R15: 00007f2944a4b010
ORIG_RAX: 0000000000000002 CS: 0033 SS: 002b
This task tried to open the cdrom device, the sr_block_open function
acquired the global sr_mutex lock. The call to check_disk_change()
then saw an event flag indicating a possible media change and tried
to flush any cached data for the device.
As part of the flush, it tried to acquire the super_block->s_umount
lock associated with the cdrom device.
This was the same super_block as created and locked by the previous task.
The first task acquires the s_umount lock and then the sr_mutex_lock;
the second task acquires the sr_mutex_lock and then the s_umount lock.
This patch fixes the issue by moving check_disk_change() out of
cdrom_open() and let the caller take care of it.
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch has been generated as follows:
for verb in set_unlocked clear_unlocked set clear; do
replace-in-files queue_flag_${verb} blk_queue_flag_${verb%_unlocked} \
$(git grep -lw queue_flag_${verb} drivers block/bsg*)
done
Except for protecting all queue flag changes with the queue lock
this patch does not change any functionality.
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Shaohua Li <shli@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Use blk_queue_flag_set() instead of open-coding this function.
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.de>
Cc: Ming Lei <ming.lei@redhat.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This patch is mostly fixes for driver specific issues (nine of them)
and the storvsc performance improvement with interrupt handling which
was dropped from the previous fixes pull request. We also have two
regressions: one is a double call_rcu() in ATA error handling and the
other is a missed conversion to BLK_STS_OK in
__scsi_error_from_host_byte().
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWp7/dCYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishSYAAP0RiYSR
oq3yLesh09tx0u+w2He8ylpdVizIzNMTjNE+BAD9GqeQWEvNaoGPUwNeMFJuwawX
hNjOttF1YOfFlsuoG94=
=9e1j
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"This is mostly fixes for driver specific issues (nine of them) and the
storvsc performance improvement with interrupt handling which was
dropped from the previous fixes pull request.
We also have two regressions: one is a double call_rcu() in ATA error
handling and the other is a missed conversion to BLK_STS_OK in
__scsi_error_from_host_byte()"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qedi: Fix kernel crash during port toggle
scsi: qla2xxx: Fix FC-NVMe LUN discovery
scsi: core: return BLK_STS_OK for DID_OK in __scsi_error_from_host_byte()
scsi: core: Avoid that ATA error handling can trigger a kernel hang or oops
scsi: qla2xxx: ensure async flags are reset correctly
scsi: qla2xxx: do not check login_state if no loop id is assigned
scsi: qla2xxx: Fixup locking for session deletion
scsi: qla2xxx: Fix NULL pointer crash due to active timer for ABTS
scsi: mpt3sas: wait for and flush running commands on shutdown/unload
scsi: mpt3sas: fix oops in error handlers after shutdown/unload
scsi: storvsc: Spread interrupts when picking a channel for I/O requests
scsi: megaraid_sas: Do not use 32-bit atomic request descriptor for Ventura controllers
If the read-only flag is true on a SCSI disk, re-reading the partition
table sets the flag back to false.
To observe this bug, you can run:
1. blockdev --setro /dev/sda
2. blockdev --rereadpt /dev/sda
3. blockdev --getro /dev/sda
This commit reads the disk's old state and combines it with the device
disk-reported state rather than unconditionally marking it as RW.
Reported-by: Li Ning <lining916740672@icloud.com>
Signed-off-by: Jeremy Cline <jeremy@jcline.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Because of the shifting around of code in qla2x00_probe_one recently,
failures during adapter initialization can lead to problems, i.e. NULL
pointer crashes and doubly freed data structures which cause eventual
panics.
This V2 version makes the relevant memory free routines idempotent, so
repeat calls won't cause any harm. I also removed the problematic
probe_init_failed exit point as it is not needed.
Fixes: d64d6c5671 ("scsi: qla2xxx: Fix NULL pointer crash due to probe failure")
Signed-off-by: Bill Kuzeja <william.kuzeja@stratus.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Rework sd_zbc_check_zone_size() to avoid a memory leak due to an early
return if sd_zbc_report_zones() fails.
Reported-by: David.butterfield <david.butterfield@wdc.com>
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Cc: stable@vger.kernel.org
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The firmware event workqueue should not be marked as WQ_MEM_RECLAIM
as it's doesn't need to make forward progress under memory pressure.
In the current state it will result in a deadlock if the device had been
forcefully removed.
Cc: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Cc: Suganath Prabu Subramani <suganath-prabu.subramani@broadcom.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit 1351e69fc6 ("scsi: lpfc: Add push-to-adapter support to sli4")
fails compilation on some 32-bit systems as writeq() is not supported on
all architectures. Additionally, it was pointed out that as writeX()
does byteswapping if necessary for pci vs the cpu endianness, the code
was broken on BE PPC.
After discussions with Arnd Bergmann, we've resolved the issue
to the following:
Instead of writeX(), use __raw_writeX() - which writes to io
space while preserving byte order. To use this, the code
was changed to use a different buffer that lpfc prepped
via sli_pcimem_bcopy() that was set to the bytestream to
be written.
On platforms with __raw_writeq support, use the routine, otherwise
use __raw_writel()
[mkp: checkpatch]
Fixes: 1351e69fc6 ("scsi: lpfc: Add push-to-adapter support to sli4")
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In scsi core, __scsi_queue_insert should just put request back on the
queue and retry using the same command as before. However, for blk-mq,
scsi_mq_requeue_cmd is employed here which will unprepare the
request. To align with the semantics of __scsi_queue_insert, use
blk_mq_requeue_request with kick_requeue_list == true and put the
reference of scsi_device.
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use dma_pool_zalloc() instead of dma_pool_alloc + memset
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Acked-by: Sumit Saxena <sumit.saxena@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Scott Benesh <scott.benesh@microsemi.com>
Signed-off-by: Kevin Barnett <kevin.barnett@microsemi.com>
Signed-off-by: Don Brace <don.brace@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The newly added code mixes up phys_addr_t/resource_size_t with dma_addr_t
and void pointers, as seen from these compiler warning:
drivers/scsi/mpt3sas/mpt3sas_base.c: In function '_base_get_chain_phys':
drivers/scsi/mpt3sas/mpt3sas_base.c:235:21: error: cast to pointer from integer of different size [-Werror=int-to-pointer-cast]
base_chain_phys = (void *)ioc->chip_phys + MPI_FRAME_START_OFFSET +
^
drivers/scsi/mpt3sas/mpt3sas_base.c: In function '_clone_sg_entries':
drivers/scsi/mpt3sas/mpt3sas_base.c:427:20: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
sgel->Address = (dma_addr_t)dst_addr_phys;
^
drivers/scsi/mpt3sas/mpt3sas_base.c:438:7: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
(dma_addr_t)buff_ptr_phys;
^
drivers/scsi/mpt3sas/mpt3sas_base.c:444:10: error: cast from pointer to integer of different size [-Werror=pointer-to-int-cast]
(dma_addr_t)buff_ptr_phys;
Both dma_addr_t and phys_addr_t may be wider than a pointer, so we must
avoid the conversion to pointer types. This also helps readability.
A second problem is treating MMIO addresses from a 'struct resource'
as addresses that can be used for DMA on that device. In almost all
cases, those are the same, but on some of the more obscure architectures,
PCI memory address 0 is mapped into the CPU address space at a nonzero
offset. I don't have a good fix for that, so I'm adding a comment here,
plus a WARN_ON() that triggers whenever the phys_addr_t number is
outside of the low 32-bit address space and causes a straight overflow
when assigned to the 32-bit sgel->Address.
Fixes: 182ac784b4 ("scsi: mpt3sas: Introduce Base function for cloning.")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
On 64 bit CPUs there is a memory corruption bug on probe(). It should
be a u32 pointer instead of an unsigned long pointer or we write past
the end of the setupdata[] array.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes the byte order of the SGPIO api and brings it back in
sync with ledmon v0.80 and above.
[mkp: added missing SoB and fixed whitespace]
Signed-off-by: Wilfried Weissmann <wilfried.weissmann@gmx.at>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid that the kernel-doc tool complains about mismatches between
kernel-doc headers and function definitions. Avoid that errors like the
following are reported when building the UFS driver with W=1:
drivers/scsi/ufs/tc-dwc-g210-pci.c:60: error: Cannot parse struct or union!
drivers/scsi/ufs/tc-dwc-g210-pltfrm.c:26: warning: cannot understand function prototype: 'struct ufs_hba_variant_ops tc_dwc_g210_20bit_pltfm_hba_vops = '
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid that the kernel-doc tool complains about a mismatch between the
kernel-doc header and the function argument list.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
commit a4239945b8 ("scsi: qla2xxx: Add switch command to simplify
fabric discovery") introduced regression when it did not consider
FC-NVMe code path which broke NVMe LUN discovery.
Fixes: a4239945b8 ("scsi: qla2xxx: Add switch command to simplify fabric discovery")
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When converting __scsi_error_from_host_byte() to BLK_STS error codes the
case DID_OK was forgotten, resulting in it always returning an error.
Fixes: 2a842acab1 ("block: introduce new block status code type")
Cc: Doug Gilbert <dgilbert@interlog.com>
Signed-off-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid that the recently introduced call_rcu() call in the SCSI core
triggers a double call_rcu() call.
Reported-by: Natanael Copa <ncopa@alpinelinux.org>
Reported-by: Damien Le Moal <damien.lemoal@wdc.com>
References: https://bugzilla.kernel.org/show_bug.cgi?id=198861
Fixes: 3bd6f43f5c ("scsi: core: Ensure that the SCSI error handler gets woken up")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Damien Le Moal <damien.lemoal@wdc.com>
Tested-by: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Natanael Copa <ncopa@alpinelinux.org>
Cc: Damien Le Moal <damien.lemoal@wdc.com>
Cc: Alexandre Oliva <oliva@gnu.org>
Cc: Pavel Tikhomirov <ptikhomirov@virtuozzo.com>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The fcport flags FCF_ASYNC_ACTIVE and FCF_ASYNC_SENT are used to
throttle the state machine, so we need to ensure to always set and unset
them correctly. Not doing so will lead to the state machine getting
confused and no login attempt into remote ports.
Cc: Quinn Tran <quinn.tran@cavium.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Fixes: 3dbec59bdf ("scsi: qla2xxx: Prevent multiple active discovery commands per session")
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When no loop id is assigned in qla24xx_fcport_handle_login() the login
state needs to be ignored; it will get set later on in
qla_chk_n2n_b4_login().
Cc: Quinn Tran <quinn.tran@cavium.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Fixes: 040036bb0b ("scsi: qla2xxx: Delay loop id allocation at login")
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Commit d8630bb95f ('Serialize session deletion by using work_lock')
tries to fixup a deadlock when deleting sessions, but fails to take into
account the locking rules. This patch resolves the situation by
introducing a separate lock for processing the GNLIST response, and
ensures that sess_lock is released before calling
qlt_schedule_sess_delete().
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: Quinn Tran <quinn.tran@cavium.com>
Fixes: d8630bb95f ("scsi: qla2xxx: Serialize session deletion by using work_lock")
Signed-off-by: Hannes Reinecke <hare@suse.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Joseph Qi <joseph.qi@linux.alibaba.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Philipp Reisner <philipp.reisner@linbit.com>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Kees Cook <keescook@chromium.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Sending I/O through 32 bit descriptors to Ventura series of controller
results in IO timeout on certain conditions. This error only occurs on
systems with high I/O activity.
Changes in this patch will prevent driver from using 32 bit descriptor
and use 64 bit Descriptors
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If the posted request has an error of any type, the IOC writes
a Reply message into a host-based system reply message frame.
This functions clone it in the BAR0 mapped region.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
1) Added function _base_clone_mpi_to_sys_mem to clone
MPI request into system BAR0 mapped region.
2) Separate out MPI Endpoint IO submissions to function
_base_put_smid_mpi_ep_scsi_io.
3) MPI EP requests are submitted in two 32 bit MMIO writes.
from _base_mpi_ep_writeq.
For 32 bit Arch,_base_writeq function is identical
to _base_mpi_ep_writeq, Removed duplicate code as suggested.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
All scsi IO's and config request's data buffer and sgl are cloned to
system memory in _clone_sg_entries before submitting it to firmware.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
For MPI Endpoint/Mcpu, driver should double buffer data buffer/SGLs.
This is normally copied from host to internal memory of IOC by DMA
engine of PCI device. Since the interface to DMA from host to mCPU is
not present for Mcpu/MPI Endpoint device, driver does double copy of
those buffers directly to the mCPU memory region via BAR0 region.
Introduced API to calculate and return BAR0 mapped host buffer's
physical and virtual address for the provided smid.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This configures shost max sector to 128, single reply descriptor post
queue, sgl table size to 16 and 32 bit DMA for MPI Endpoint and it
supports 64K as max IO.
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add device ID and flag for Andromeda/MPI Endpoint.
[mkp: typo]
Signed-off-by: Suganath Prabu S <suganath-prabu.subramani@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
No functional changes. Just fix two wrong indentation cases in
scsi_finish_command and scsi_decide_disposition.
Signed-off-by: Jianchao Wang <jianchao.w.wang@oracle.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A bugfix I did caused a build regression in some other randconfig
builds in a rare combination of options:
In file included from drivers/scsi/qedi/qedi_fw.c:16:
drivers/scsi/qedi/qedi_gbl.h:26:38: error: array type has incomplete element type 'struct qedi_debugfs_ops'
extern const struct qedi_debugfs_ops qedi_debugfs_ops[];
^~~~~~~~~~~~~~~~
This removes the useless #ifdef around the declarations in qedi_dbg.h
to make it always build.
Fixes: 779936faf4 ("scsi: qedi: fix building with LTO")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Avoid that building with W=1 causes the kernel-doc tool to complain
about function arguments that have not been documented in the libsas
kernel-doc headers. Avoid that the short description starts with a
hyphen by changing "--" into "-" in the first line of the kernel-doc
headers.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: John Garry <john.garry@huawei.com>
Reviewed-by: John Garry <john.garry@huawei.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
These are mostly fixes for problems with merge window code. In
addition we have one doc update (alua) and two dead code removals
(aiclib and octogon) a spurious assignment removal (csiostor) and a
performance improvement for storvsc involving better interrupt
spreading and increasing the command per lun handling.
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWo+H2yYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishe2eAQDyWfoK
Mfjbrl6cdPop+JIoED0VtBzAQyeXceJt8GYDQwEApXTIZon2HTdJqGawfUhaapBA
JnO6iOiC13/nZjl7C28=
=K3Pk
-----END PGP SIGNATURE-----
Merge tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"These are mostly fixes for problems with merge window code.
In addition we have one doc update (alua) and two dead code removals
(aiclib and octogon) a spurious assignment removal (csiostor) and a
performance improvement for storvsc involving better interrupt
spreading and increasing the command per lun handling"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: qla4xxx: skip error recovery in case of register disconnect.
scsi: aacraid: fix shutdown crash when init fails
scsi: qedi: Cleanup local str variable
scsi: qedi: Fix truncation of CHAP name and secret
scsi: qla2xxx: Fix incorrect handle for abort IOCB
scsi: qla2xxx: Fix double free bug after firmware timeout
scsi: storvsc: Increase cmd_per_lun for higher speed devices
scsi: qla2xxx: Fix a locking imbalance in qlt_24xx_handle_els()
scsi: scsi_dh: Document alua_rtpg_queue() arguments
scsi: Remove Makefile entry for oktagon files
scsi: aic7xxx: remove aiclib.c
scsi: qla2xxx: Avoid triggering undefined behavior in qla2x00_mbx_completion()
scsi: mptfusion: Add bounds check in mptctl_hp_targetinfo()
scsi: sym53c8xx_2: iterator underflow in sym_getsync()
scsi: bnx2fc: Fix check in SCSI completion handler for timed out request
scsi: csiostor: remove redundant assignment to pointer 'ln'
scsi: ufs: Enable quirk to ignore sending WRITE_SAME command
scsi: ibmvfc: fix misdefined reserved field in ibmvfc_fcp_rsp_info
scsi: qla2xxx: Fix memory corruption during hba reset test
scsi: mpt3sas: fix an out of bound write
Updated Copyright in files updated as part of 12.0.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 12.0.0.0
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The hardware offload for NVME commands was created when the
FC-NVME standard was setting SGL Descriptor Type to SGL Data
Block Descriptor (0h) and SGL Descriptor Sub Type to Address (0h).
A late change in NVMe-over-Fabrics obsoleted these values, creating
a transport SGL descriptor type with new values to go into these
fields.
For initial hardware support, in order to be compliant to the spec,
use host-supplied cmd IU buffers instead of the adapter generated
values. Later hardware will correct this.
Add a module parameter to override this offload disablement if looking
for lowest latency. This is reasonable as nothing in FC-NVME uses
the SQE SGL values.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Newer hardware more strictly enforces buffer lenghts, causing an
mis-set value to be identified. Older hardware won't catch it.
The difference is benign on old hardware.
Set the right embedded buffer length for nvme ios.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The current driver isn't taking advantage of a performance hint whereby
the initial data buffer descriptor can be placed in the WQE as well as
the SGL.
Add the logic to detect support for the feature and to use it when
supported.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Current code is very explicit in what it allows to be downloaded.
The driver checking prevented G7 firmware download. The driver
checking is unnecessary as the device will validate what it receives.
Revise the firmware download interface checking.
Added a little debug support in case there is still a failure.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Traditional SLI4 required the driver to clear Valid bits on
EQEs and CQEs after consuming them.
The new if_type=6 hardware will cycle the value for what is
valid on each queue itteration. The driver no longer has to
touch the valid bits. This also means all the cpu cache
dirtying and perhaps flush/refill's done by the hardware
in accessing the EQ/CQ elements is eliminated.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The G7 adapter supports 64G link speeds. Add support to the driver.
In addition, a small cleanup to replace the odd bitmap logic with
a switch case.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Add PCI ids for the new G7 adapter
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
New if_type=6 adapters support an additional BAR that provides
apertures to allow direct WQE to adapter push support - termed
Direct Packet Push (DPP). WQ creation differs slightly to ask for
a WQ to be DPP-ized. When submitting a WQE to a DPP WQ, it is
submitted to the host memory for the WQ normally, but is also
written by the host cpu directly to a BAR aperture. Write buffer
coalescing in hardware is (hopefully) turned on, enabling single
pci write operation support. The doorbell is thing rung to indicate
the WQE is available and was pushed to the aperture.
This patch:
- Updates the WQ Create commands for the DPP options
- Adds the bar mapping for if_type=6 DPP bar
- Adds the WQE pushing to the DDP aperture received from WQ create
- Adds a new module parameter to disable DPP operation if desired.
Default is enabled.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
New hardware supports a SLI-4 interface, but with a new if_type
variant of 6.
If_type=6 has a different PCI BAR map, separate EQ/CQ doorbells,
and some changes in doorbell formats.
Add the changes for the if_type into headers, adapter initialization
and control flows. Add new eq and cq handlers.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Up until now, all SLI-4 devices had the same doorbells at the same
bar locations. With newer hardware, there are now independent EQ and
CQ doorbells and the bar locations differ.
Prepare the code for new hardware by separating the eq/cq doorbell into
separate components. The components can be set based on if_type.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Up until now, an SLI-4 device had no variance in the way it handled
its EQs and CQs. With newer hardware, there are now differences in
doorbells and some differences in how entries are valid.
Prepare the code for new hardware by creating a sli4-based callout
table that can be set based on if_type.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use dma_pool_zalloc() instead of dma_pool_alloc + memset
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch finishes all outstanding SCSI IO commands (but not other commands,
e.g., task management) in the shutdown and unload paths.
It first waits for the commands to complete (this is done after setting
'ioc->remove_host = 1 ', which prevents new commands to be queued) then it
flushes commands that might still be running.
This avoids triggering error handling (e.g., abort command) for all commands
possibly completed by the adapter after interrupts disabled.
[mauricfo: introduced something in commit message.]
Signed-off-by: Sreekanth Reddy <sreekanth.reddy@broadcom.com>
Tested-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds checks for 'ioc->remove_host' in the SCSI error handlers, so
not to access pointers/resources potentially freed in the PCI shutdown/module
unload path. The error handlers may be invoked after shutdown/unload,
depending on other components.
This problem was observed with kexec on a system with a mpt3sas based adapter
and an infiniband adapter which takes long enough to shutdown:
The mpt3sas driver finished shutting down / disabled interrupt handling, thus
some commands have not finished and timed out.
Since the system was still running (waiting for the infiniband adapter to
shutdown), the scsi error handler for task abort of mpt3sas was invoked, and
hit an oops -- either in scsih_abort() because 'ioc->scsi_lookup' was NULL
without commit dbec4c9040 ("scsi: mpt3sas: lockless command submission"), or
later up in scsih_host_reset() (with or without that commit), because it
eventually called mpt3sas_base_get_iocstate().
After the above commit, the oops in scsih_abort() does not occur anymore
(_scsih_scsi_lookup_find_by_scmd() is no longer called), but that commit is
too big and out of the scope of linux-stable, where this patch might help, so
still go for the changes.
Also, this might help to prevent similar errors in the future, in case code
changes and possibly tries to access freed stuff.
Note the fix in scsih_host_reset() is still important anyway.
Signed-off-by: Mauricio Faria de Oliveira <mauricfo@linux.vnet.ibm.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use dma_pool_zalloc() instead of dma_pool_alloc + memset
Signed-off-by: Souptick Joarder <jrdr.linux@gmail.com>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the algorithm in storvsc_do_io to look for a channel
starting with the current CPU + 1 and wrap around (within the
current NUMA node). This spreads VMbus interrupts more evenly
across CPUs. Previous code always started with first CPU in
the current NUMA node, skewing the interrupt load to that CPU.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: Long Li <longli@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces a sysfs group entry for the UFS attributes. The
group adds "attributes" folder under the UFS driver sysfs entry
(/sys/bus/platform/drivers/ufshcd/*). The attributes are shown
as hexadecimal numbers. The full information about the attributes could
be found at UFS specifications 2.1.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces a sysfs group entry for the UFS flags. The group adds
"flags" folder under the UFS driver sysfs entry
(/sys/bus/platform/drivers/ufshcd/*). The flags are shown as boolean value
("true" or "false"). The full information about the UFS flags could be
found at UFS specifications 2.1.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces a sysfs group entry for the UFS unit descriptor
parameters. The group adds "unit_descriptor" folder under the corresponding
SCSI device sysfs entry (/sys/class/scsi_device/*/device/). The parameters
are shown as hexadecimal numbers. The full information about the parameters
could be found at UFS specifications 2.1.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The patch introduces an additional field in the scsi_host_template
structure - struct attribute_group **sdev_group. This field allows to
define groups of attributes. It will provide an ability to use binary
attributes as well as device attributes and to group them under
subfolders if necessary.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces a sysfs group entry for the UFS string descriptors.
The group adds "string_descriptors" folder under the UFS driver
sysfs entry (/sys/bus/platform/drivers/ufshcd/*). The folder will contain
5 files that will show string values defined by the UFS spec:
a manufacturer name, a product name, an OEM id, a serial number and a
product revision. The full information about the string descriptors
could be found at UFS specifications 2.1.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces a sysfs group entry for the UFS power descriptor
parameters. The group adds "power_descriptor" folder under the UFS driver
sysfs entry (/sys/bus/platform/drivers/ufshcd/*). The parameters are shown
as hexadecimal numbers. The full information about the parameters could be
found at UFS specifications 2.1.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces a sysfs group entry for the UFS health descriptor
parameters. The group adds "health_descriptor" folder under the UFS driver
sysfs entry (/sys/bus/platform/drivers/ufshcd/*). The parameters are shown
as hexadecimal numbers. The full information about the parameters could be
found at UFS specifications 2.1.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces a sysfs group entry for the UFS geometry descriptor
parameters. The group adds "geometry_descriptor" folder under the UFS
driver sysfs entry (/sys/bus/platform/drivers/ufshcd/*). The parameters
are shown as hexadecimal numbers. The full information about the parameters
could be found at UFS specifications 2.1.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces a sysfs group entry for the UFS interconnect
descriptor parameters. The group adds "interconnect_descriptor" folder
under the UFS driver sysfs entry (/sys/bus/platform/drivers/ufshcd/*).
The parameters are shown as hexadecimal numbers. The full information
about the parameters could be found at UFS specifications 2.1.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces a sysfs group entry for the UFS device descriptor
parameters. The group adds "device_descriptor" folder under the UFS driver
sysfs entry (/sys/bus/platform/drivers/ufshcd/*). The parameters are shown
as hexadecimal numbers. The full information about the parameters could be
found at UFS specifications 2.1.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch introduces attribute group to show existing sysfs entries.
Signed-off-by: Stanislav Nijnikov <stanislav.nijnikov@wdc.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Error injection in scsi_debug (e.g. opts=16, SDEBUG_OPT_TRANSPORT_ERR)
currently doesn't work correctly because the test for sqcp in
resp_read_dt0() and similar resp_*() functions always fails. sqcp is
set from cmnd->host_scribble, which is set in schedule_resp(), which is
called from scsi_debug_queuecommand() after calling the resp_* function.
Defer calling resp_*() until after cmnd->host_scribble is set in
schedule_resp().
Fixes: c483739430 "scsi_debug: add multiple queue support"
Signed-off-by: Martin Wilck <mwilck@suse.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Problem Statement: Sending I/O through 32 bit descriptors to Ventura series of
controller results in IO timeout on certain conditions.
This error only occurs on systems with high I/O activity on Ventura series
controllers.
Changes in this patch will prevent driver from using 32 bit descriptor and use
64 bit Descriptors.
Cc: <stable@vger.kernel.org>
Signed-off-by: Kashyap Desai <kashyap.desai@broadcom.com>
Signed-off-by: Shivasharan S <shivasharan.srikanteshwara@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Don't populate the const read-only arrays spi_test_unit_ready and
spi_test_unit_ready on the stack but instead make them static. Makes the
object code smaller by over 100 bytes:
Before:
text data bss dec hex filename
40171 12832 128 53131 cf8b drivers/scsi/scsi_transport_spi.o
After:
text data bss dec hex filename
39922 12976 128 53026 cf22 drivers/scsi/scsi_transport_spi.o
(gcc version 7.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
If every_nth > 0, the injection flags must be reset for commands that
aren't supposed to fail (i.e. that aren't "nth"). Otherwise, commands
will continue to fail, like in the every_nth < 0 case.
Signed-off-by: Martin Wilck <mwilck@suse.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The Start Stop Unit (SSU) command takes in the order of a second to complete
on some SAS SSDs and longer on hard disks. Synchronize Cache (SC) can also
take some time. Both commands have an IMMED bit in their cdbs for those apps
that don't want to wait. This patch introduces a long delay for those commands
when the IMMED bit is clear. Since SC is a media access command then when the
fake_rw option is active, its cdb processing is skipped and it returns
immediately. The SSU command is not altered by the setting of the fake_rw
option. These actions are not changed by this patch.
Changes since v1:
- clear the cdb mask of SYNCHRONIZE CACHE(16) cdb in byte 1, bit 0
Changes:
- add the SYNCHRONIZE CACHE(16) command
- together with the existing START STOP UNIT and SYNCHRONIZE CACHE(10)
commands process the IMMED bit in their cdbs
- if the IMMED bit is set, return immediately
- if the IMMED bit is clear, treat the delay parameter as having
a unit of one second
- in the SYNCHRONIZE CACHE processing do a bounds check
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pointer styling issues exposed by checkpatch.pl in scsi_debug.c:
ERROR: "foo * bar" should be "foo *bar"
Fixed 37 total errors reported.
[mkp: fixed typo noticed by Doug]
Signed-off-by: John Pittman <jpittman@redhat.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make scsi_test_unit_ready() send at most as many TURs as specified in
the 'retries' argument instead of retries * (retries + 1) / 2.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The eh_deadline definition occurs in the middle of the code for
releasing a host. Avoid splitting the host release code by moving the
definition of the eh_deadline parameter to the top of the hosts.c source
file.
Signed-off-by: Bart Van Assche <bart.vanassche@sandisk.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
After the patch that introduced this function was posted on the
linux-scsi mailing list an explanation was posted why this patch is
correct. Since that explanation contains important information, add a
summary of it above the code that explanation applies to. See also
http://www.spinics.net/lists/linux-scsi/msg106326.html.
References: e494f6a728 ("[SCSI] improved eh timeout handler")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the sgl_alloc_order() and sgl_free_order() functions instead of open
coding these functions.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Anil Ravindranath <anil_ravindranath@pmc-sierra.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Use the sgl_alloc_order() and sgl_free_order() functions instead of open
coding these functions.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Cc: Martin K. Petersen <martin.petersen@oracle.com>
Cc: linux-scsi@vger.kernel.org
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
There are several occurrances where pointer ioadl is initialized with a
value that is never read and where it is re-assigned a new value later
on, hence the initialization is redundant and can be removed.
Cleans up clang warnings:
drivers/scsi/pmcraid.c:1028:29: warning: Value stored to 'ioadl' during
its initialization is never read
drivers/scsi/pmcraid.c:3178:29: warning: Value stored to 'ioadl' during
its initialization is never read
drivers/scsi/pmcraid.c:5495:29: warning: Value stored to 'ioadl' during
its initialization is never read
drivers/scsi/pmcraid.c:5668:29: warning: Value stored to 'ioadl' during
its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Variable bit is initialized with a value that is never read and is being
updated immediately after the initialization, hence the initialization
is redundant and can be removed.
Cleans up clang warning:
drivers/scsi/isci/host.c:2769:8: warning: Value stored to 'bit' during
its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Building with link time optimizations produces a false-positive section
mismatch warning:
WARNING: vmlinux.o(.data+0xf8c8): Section mismatch in reference from the variable driver_template.lto_priv.6915 to the function .init.text:sym53c416_detect()
The variable driver_template.lto_priv.6915 references
the function __init sym53c416_detect()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
The ->detect callback is always entered from the init_this_scsi_driver()
init function, but apparently LTO turns the optimized direct function
call into an indirect call through a non-__initdata pointer.
All drivers using init_this_scsi_driver() are for ancient hardware,
and most don't mark the detect() callback as __init(), so I'm
just removing the annotation here to kill off the warning instead
of doing a larger rework.
[mkp: typo]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Building with link time optimizations produces a false-positive section
mismatch warning:
WARNING: vmlinux.o(.data+0xf7e8): Section mismatch in reference from the variable driver_template.lto_priv.6914 to the function .init.text:NCR53c406a_detect()
The variable driver_template.lto_priv.6914 references
the function __init NCR53c406a_detect()
If the reference is valid then annotate the
variable with __init* or __refdata (see linux/init.h) or name the variable:
*_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console
The ->detect callback is always entered from the init_this_scsi_driver()
init function, but apparently LTO turns the optimized direct function
call into an indirect call through a non-__initdata pointer.
All drivers using init_this_scsi_driver() are for ancient hardware, and
most don't mark the detect() callback as __init(), so I'm just removing
the annotation here to kill off the warning instead of doing a larger
rework.
[mkp: typo]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During sync command processing, if legacy INTx status indicates command
is not completed, sample the MSIx register and check if it indicates
command completion, set controller MSIx enabled flag.
Signed-off-by: Prasad B Munirathnam <prasad.munirathnam@microsemi.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Preserve the current MSIX mode value in the OMR before rewriting the OMR
to initiate the IOP or Soft Reset.
Signed-off-by: Prasad B Munirathnam <prasad.munirathnam@microsemi.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
IOP_RESET takes a long time to complete. If controller is in a state
where we can bring it back with init struct, send a DropIO sync command
instead.
- If controller is faulted perform standard IOP_RESET in aac_srcv_init.
- If controller is not faulted get adapter properties and extended
properties.
- Update the sa_firmware variable and determine if DropIO request is
supported.
- Issue DropIO request, and get the number of outstanding commands.
- If all commands are complete with success (CT_OK), consider IOP_RESET
is complete.
- If any commands timeout, Perform the IOP_RESET.
Signed-off-by: Prasad B Munirathnam <prasad.munirathnam@microsemi.com>
Signed-off-by: Raghava Aditya Renukunta <RaghavaAditya.Renukunta@microsemi.com>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
gcc-8 warns during link-time optimization that the strncpy() call passes
the size of the source buffer rather than the destination:
drivers/scsi/qedf/qedf_dbg.c: In function 'qedf_uevent_emit':
include/linux/string.h:253: error: 'strncpy' specified bound depends on the length of the source argument [-Werror=stringop-overflow=]
This changes it to strscpy() with the correct length, guaranteeing a
properly nul-terminated string of the right size.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The prototype for qedf_dbg_fops/qedf_debugfs_ops doesn't match the definition,
which causes the final link to fail with link-time optimizations:
drivers/scsi/qedf/qedf_main.c:34: error: type of 'qedf_dbg_fops' does not match original declaration [-Werror=lto-type-mismatch]
extern struct file_operations qedf_dbg_fops;
drivers/scsi/qedf/qedf_debugfs.c:443: note: 'qedf_dbg_fops' was previously declared here
const struct file_operations qedf_dbg_fops[] = {
drivers/scsi/qedf/qedf_main.c:33: error: type of 'qedf_debugfs_ops' does not match original declaration [-Werror=lto-type-mismatch]
extern struct qedf_debugfs_ops qedf_debugfs_ops;
drivers/scsi/qedf/qedf_debugfs.c:102: note: 'qedf_debugfs_ops' was previously declared here
struct qedf_debugfs_ops qedf_debugfs_ops[] = {
This corrects the prototype and moves it into a shared header file where it
belongs. The file operations can also be marked 'const' like the
qedf_debugfs_ops.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pointer disc is being intializated a value that is never read and then
re-assigned the same value later on, hence the initialization is
redundant and can be removed.
Cleans up clang warning:
drivers/scsi/libfc/fc_disc.c:734:18: warning: Value stored to 'disc'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Pointer fcport is initialized with a value that is never read, it is
re-assigned a new value later on, hence the initialization is redundant
and can be removed.
Cleans up clang warning:
drivers/scsi/qedf/qedf_io.c:920:21: warning: Value stored to 'fcport'
during its initialization is never read
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Chad Dupuis <chad.dupuis@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When link-time optimizations are enabled, qedi fails to build because
of mismatched prototypes:
drivers/scsi/qedi/qedi_gbl.h:27:37: error: type of 'qedi_dbg_fops' does not match original declaration [-Werror=lto-type-mismatch]
extern const struct file_operations qedi_dbg_fops;
^
drivers/scsi/qedi/qedi_debugfs.c:239:30: note: 'qedi_dbg_fops' was previously declared here
const struct file_operations qedi_dbg_fops[] = {
^
drivers/scsi/qedi/qedi_gbl.h:26:32: error: type of 'qedi_debugfs_ops' does not match original declaration [-Werror=lto-type-mismatch]
extern struct qedi_debugfs_ops qedi_debugfs_ops;
^
drivers/scsi/qedi/qedi_debugfs.c:102:25: note: 'qedi_debugfs_ops' was previously declared here
struct qedi_debugfs_ops qedi_debugfs_ops[] = {
This changes the declaration to match the definition, and adapts the
users as necessary. Since both array can be constant here, I'm adding
the 'const' everywhere for consistency.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Manish Rangankar <Manish.Rangankar@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch adds two new parameters to the scsi_debug driver.
During various fault injection scenarios it would be useful to be able
to pick a specific starting sector and number of follow on sectors where
a MEDIUM ERROR for reads would be returned against a scsi-debug device.
Right now this only works against sector 0x1234 and OPT_MEDIUM_ERR_NUM
follow on sectors. However during testing of md-raid and other
scenarios I wanted more flexibility.
The idea is add 2 new parameters:
medium_error_start
medium_error_count
If medium_error_start is set then we don't use the default of
OPT_MEDIUM_ERR_ADDR, but use that set value.
If medium_error_count is set we use that value otherwise default to
OPT_MEDIUM_ERR_NUM.
Signed-off-by: Laurence Oberman <loberman@redhat.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A system crashes when continuously removing/re-adding the storage
controller.
Signed-off-by: Manish Rangankar <manish.rangankar@cavium.com>
Reviewed-by: Ewan D. Milne <emilne@redhat.com>
Reviewed-by: Tomas Henzl <thenzl@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When aacraid init fails with "AAC0: adapter self-test failed.", shutdown
leads to UBSAN warning and then oops:
[154316.118423] ================================================================================
[154316.118508] UBSAN: Undefined behaviour in drivers/scsi/scsi_lib.c:2328:27
[154316.118566] member access within null pointer of type 'struct Scsi_Host'
[154316.118631] CPU: 2 PID: 14530 Comm: reboot Tainted: G W 4.15.0-dirty #89
[154316.118701] Hardware name: Hewlett Packard HP NetServer/HP System Board, BIOS 4.06.46 PW 06/25/2003
[154316.118774] Call Trace:
[154316.118848] dump_stack+0x48/0x65
[154316.118916] ubsan_epilogue+0xe/0x40
[154316.118976] __ubsan_handle_type_mismatch+0xfb/0x180
[154316.119043] scsi_block_requests+0x20/0x30
[154316.119135] aac_shutdown+0x18/0x40 [aacraid]
[154316.119196] pci_device_shutdown+0x33/0x50
[154316.119269] device_shutdown+0x18a/0x390
[...]
[154316.123435] BUG: unable to handle kernel NULL pointer dereference at 000000f4
[154316.123515] IP: scsi_block_requests+0xa/0x30
This is because aac_shutdown() does
struct Scsi_Host *shost = pci_get_drvdata(dev);
scsi_block_requests(shost);
and that assumes shost has been assigned with pci_set_drvdata().
However, pci_set_drvdata(pdev, shost) is done in aac_probe_one() far
after bailing out with error from calling the init function
((*aac_drivers[index].init)(aac)), and when the init function fails, no
error is returned from aac_probe_one() so PCI layer assumes there is
driver attached, and tries to shut it down later.
Fix it by returning error from aac_probe_one() when card-specific init
function fails.
This fixes reboot on my HP NetRAID-4M with dead battery.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Reviewed-by: Dave Carroll <david.carroll@microsemi.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Nilesh Javali <nilesh.javali@cavium.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Chris Leech <cleech@redhat.com>
Acked-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The data in NVRAM is not guaranteed to be NUL terminated. Since
snprintf expects byte-stream to accommodate null byte, the CHAP secret
is truncated. Use sprintf instead of snprintf to fix the truncation of
CHAP name and secret.
Signed-off-by: Andrew Vasquez <andrew.vasquez@cavium.com>
Signed-off-by: Nilesh Javali <nilesh.javali@cavium.com>
Reviewed-by: Bart Van Assche <bart.vanassche@wdc.com>
Acked-by: Chris Leech <cleech@redhat.com>
Acked-by: Lee Duncan <lduncan@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch fixes incorrect handle used for abort IOCB.
Fixes: b027a5ace4 ("scsi: qla2xxx: Fix queue ID for async abort with Multiqueue")
Signed-off-by: Darren Trapp <darren.trapp@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch is based on Max's original patch.
When the qla2xxx firmware is unavailable, eventually
qla2x00_sp_timeout() is reached, which calls the timeout function and
frees the srb_t instance.
The timeout function always resolves to qla2x00_async_iocb_timeout(),
which invokes another callback function called "done". All of these
qla2x00_*_sp_done() callbacks also free the srb_t instance; after
returning to qla2x00_sp_timeout(), it is freed again.
The fix is to remove the "sp->free(sp)" call from qla2x00_sp_timeout()
and add it to those code paths in qla2x00_async_iocb_timeout() which
do not already free the object.
This is how it looks like with KASAN:
BUG: KASAN: use-after-free in qla2x00_sp_timeout+0x228/0x250
Read of size 8 at addr ffff88278147a590 by task swapper/2/0
Allocated by task 1502:
save_stack+0x33/0xa0
kasan_kmalloc+0xa0/0xd0
kmem_cache_alloc+0xb8/0x1c0
mempool_alloc+0xd6/0x260
qla24xx_async_gnl+0x3c5/0x1100
Freed by task 0:
save_stack+0x33/0xa0
kasan_slab_free+0x72/0xc0
kmem_cache_free+0x75/0x200
qla24xx_async_gnl_sp_done+0x556/0x9e0
qla2x00_async_iocb_timeout+0x1c7/0x420
qla2x00_sp_timeout+0x16d/0x250
call_timer_fn+0x36/0x200
The buggy address belongs to the object at ffff88278147a440
which belongs to the cache qla2xxx_srbs of size 344
The buggy address is located 336 bytes inside of
344-byte region [ffff88278147a440, ffff88278147a598)
Reported-by: Max Kellermann <mk@cm4all.com>
Signed-off-by: Quinn Tran <quinn.tran@cavium.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: Max Kellermann <mk@cm4all.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Increase cmd_per_lun to allow more I/Os in progress per device,
particularly for NVMe's. The Hyper-V host side can handle the higher
count with no issues.
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Reviewed-by: K. Y. Srinivasan <kys@microsoft.com>
Acked-by: K. Y. Srinivasan <kys@microsoft.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Since commit 64d513ac31 ("scsi: use host wide tags by default") all
SCSI requests have a tag, whether or not scsi-mq is enabled.
Additionally, it is safe to use blk_mq_unique_tag() and
blk_mq_unique_tag_to_hwq() for legacy SCSI queues. Since this means that
the sdebug_mq_active variable is superfluous, remove it.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Douglas Gilbert <dgilbert@interlog.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Hannes Reinecke <hare@suse.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Changes since v1:
Added changes in these files:
drivers/infiniband/hw/usnic/usnic_transport.c
drivers/staging/lustre/lnet/lnet/lib-socket.c
drivers/target/iscsi/iscsi_target_login.c
drivers/vhost/net.c
fs/dlm/lowcomms.c
fs/ocfs2/cluster/tcp.c
security/tomoyo/network.c
Before:
All these functions either return a negative error indicator,
or store length of sockaddr into "int *socklen" parameter
and return zero on success.
"int *socklen" parameter is awkward. For example, if caller does not
care, it still needs to provide on-stack storage for the value
it does not need.
None of the many FOO_getname() functions of various protocols
ever used old value of *socklen. They always just overwrite it.
This change drops this parameter, and makes all these functions, on success,
return length of sockaddr. It's always >= 0 and can be differentiated
from an error.
Tests in callers are changed from "if (err)" to "if (err < 0)", where needed.
rpc_sockname() lost "int buflen" parameter, since its only use was
to be passed to kernel_getsockname() as &buflen and subsequently
not used in any way.
Userspace API is not changed.
text data bss dec hex filename
30108430 2633624 873672 33615726 200ef6e vmlinux.before.o
30108109 2633612 873672 33615393 200ee21 vmlinux.o
Signed-off-by: Denys Vlasenko <dvlasenk@redhat.com>
CC: David S. Miller <davem@davemloft.net>
CC: linux-kernel@vger.kernel.org
CC: netdev@vger.kernel.org
CC: linux-bluetooth@vger.kernel.org
CC: linux-decnet-user@lists.sourceforge.net
CC: linux-wireless@vger.kernel.org
CC: linux-rdma@vger.kernel.org
CC: linux-sctp@vger.kernel.org
CC: linux-nfs@vger.kernel.org
CC: linux-x25@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Not a real RAID level, but some HBAs support JBOD in addition to the
'classical' RAID levels.
Signed-off-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Bring the kernel-doc headers in sync with the function argument lists.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This patch does not change any functionality but slightly reduces
the size of the compiled kernel module.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove a few preprocessor macros that are not used anywhere.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Remove a few preprocessor macros that are not used anywhere.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Using %p instead of %lx to print a pointer allows to remove a cast.
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Updated Copyright in files updated 11.4.0.7
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Update the driver version to 11.4.0.7
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
In a test that is doing large numbers of cable swaps on the target, the
nvme controllers wouldn't reconnect.
During the cable swaps, the targets n_port_id would change. This
information was passed to the nvme-fc transport, in the new remoteport
registration. However, the nvme-fc transport didn't update the n_port_id
value in the remoteport struct when it reused an existing structure.
Later, when a new association was attempted on the remoteport, the
driver's NVME LS routine would use the stale n_port_id from the
remoteport struct to address the LS. As the device is no longer at that
address, the LS would go into never never land.
Separately, the nvme-fc transport will be corrected to update the
n_port_id value on a re-registration.
However, for now, there's no reason to use the transports values. The
private pointer points to the drivers node structure and the node
structure is up to date. Therefore, revise the LS routine to use the
drivers data structures for the LS. Augmented the debug message for
better debugging in the future.
Also removed a duplicate if check that seems to have slipped in.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Currently, write underruns (mismatch of amount transferred vs scsi
status and its residual) detected by the adapter are not being flagged
as an error. Its expected the target controls the data transfer and
would appropriately set the RSP values. Only read underruns are treated
as errors.
Revise the SCSI error handling to treat write underruns as an error as
well.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver was inappropriately pulling in the nvme host's nvme.h
header. What it really needed was the standard <linux/nvme.h> header.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When using the special option to suppress the response iu, ensure the
adapter fully supports the feature by checking feature flags from the
adapter and validating the support when formatting the WQE.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During SCSI error handling escalation to host reset, the SCSI io
routines were moved off the txcmplq, but the individual io's ON_CMPLQ
flag wasn't cleared. Thus, a background thread saw the io and attempted
to access it as if on the txcmplq.
Clear the flag upon removal.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Revise the NVME PRLI to indicate CONF support.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver ignored checks on whether the link should be kept
administratively down after a link bounce. Correct the checks.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
During link bounce testing in a point-to-point topology, the host may
enter a soft lockup on the lpfc_worker thread:
Call Trace:
lpfc_work_done+0x1f3/0x1390 [lpfc]
lpfc_do_work+0x16f/0x180 [lpfc]
kthread+0xc7/0xe0
ret_from_fork+0x3f/0x70
The driver was simultaneously setting a combination of flags that caused
lpfc_do_work()to effectively spin between slow path work and new event
data, causing the lockup.
Ensure in the typical wq completions, that new event data flags are set
if the slow path flag is running. The slow path will eventually
reschedule the wq handling.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Make the attribute writeable.
Remove the ramp up to logic as its unnecessary, simply set depth. Add
debug message if depth changed, possibly reducing limit, yet our
outstanding count has yet to catch up with it.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
When nvme target deferred receive logic waits for exchange resources,
the corresponding receive buffer is not replenished with the hardware.
This can result in a lack of asynchronous receive buffer resources in
the hardware, resulting in a "2885 Port Status Event: ... error
1=0x52004a01 ..." message.
Correct by replenishing the buffer whenenver the deferred logic kicks
in. Update corresponding debug messages and statistics as well.
[mkp: applied by hand]
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
A stress test repeatedly resetting the adapter while performing io would
eventually report I/O failures and missing nvme namespaces.
The driver was setting the nvmefc_fcp_req->private pointer to NULL
during the IO completion routine before upcalling done(). If the
transport was also running an abort for that IO, the driver would fail
the abort with message 6140. Failing the abort is not allowed by the
nvme-fc transport, as it mandates that the io must be returned back to
the transport. As that does not happen, the transport controller delete
has an outstanding reference and can't complete teardown.
The NULL-ing of the private pointer should be done only when the io is
considered complete. It's complete when the adapter returns the exchange
with the "exchange busy" flag clear.
Move the NULL'ing of the structure to the done case. This leaves the io
contexts set while it is busy and until the subsequent XRI_ABORTED
completion which returns the exchange is received.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The lpfc driver does not discover a target when the topology changes
from switched-fabric to direct-connect. The target rejects the PRLI from
the initiator in direct-connect as the driver is using the old S_ID from
the switched topology.
The driver was inappropriately clearing the VP bit to register the VPI,
which is what is associated with the S_ID.
Fix by leaving the VP bit set (it was set earlier) and as the VFI is
being re-registered, set the UPDT bit.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
I/O conditions on the nvme target may have the driver submitting to a
full hardware wq. The hardware wq is a shared resource among all nvme
controllers. When the driver hit a full wq, it failed the io posting
back to the nvme-fc transport, which then escalated it into errors.
Correct by maintaining a sideband queue within the driver that is added
to when the WQ full condition is hit, and drained from as soon as new WQ
space opens up.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Existing code was using the wrong field for the completion status when
comparing whether to increment abort statistics
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Ensure nvme localports/targetports are torn down before dismantling the
adapter sli interface on driver detachment. This aids leaving
interfaces live while nvme may be making callbacks to abort it.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Increased CQ and WQ sizes for SCSI FCP, matching those used for NVMe
development.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
The driver controls when the hardware sends completions that communicate
consumption of elements from the WQ. This is done by setting a WQEC bit
on a WQE.
The current driver sets it on every Nth WQE posting. However, the driver
isn't clearing the bit if the WQE is reused. Thus, if the queue depth
isn't evenly divisible by N, with enough time, it can be set on every
element, creating a lot of overhead and risking CQ full conditions.
Correct by clearing the bit when not setting it on an Nth element.
Signed-off-by: Dick Kennedy <dick.kennedy@broadcom.com>
Signed-off-by: James Smart <james.smart@broadcom.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
This is the mindless scripted replacement of kernel use of POLL*
variables as described by Al, done by this script:
for V in IN OUT PRI ERR RDNORM RDBAND WRNORM WRBAND HUP RDHUP NVAL MSG; do
L=`git grep -l -w POLL$V | grep -v '^t' | grep -v /um/ | grep -v '^sa' | grep -v '/poll.h$'|grep -v '^D'`
for f in $L; do sed -i "-es/^\([^\"]*\)\(\<POLL$V\>\)/\\1E\\2/" $f; done
done
with de-mangling cleanups yet to come.
NOTE! On almost all architectures, the EPOLL* constants have the same
values as the POLL* constants do. But they keyword here is "almost".
For various bad reasons they aren't the same, and epoll() doesn't
actually work quite correctly in some cases due to this on Sparc et al.
The next patch from Al will sort out the final differences, and we
should be all done.
Scripted-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Ensure that upon return the tgt->ha->tgt.sess_lock spin lock is unlocked
no matter which code path is taken through this function. This was
detected by sparse.
Fixes: 82abdcaf3e ("scsi: qla2xxx: Allow target mode to accept PRLI in dual mode")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Himanshu Madhani <himanshu.madhani@cavium.com>
Cc: Quinn Tran <quinn.tran@cavium.com>
Acked-by: Himanshu Madhani <himanshu.madhani@cavium.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=qeDb
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20180204' of git://git.kernel.dk/linux-block
Pull more block updates from Jens Axboe:
"Most of this is fixes and not new code/features:
- skd fix from Arnd, fixing a build error dependent on sla allocator
type.
- blk-mq scheduler discard merging fixes, one from me and one from
Keith. This fixes a segment miscalculation for blk-mq-sched, where
we mistakenly think two segments are physically contigious even
though the request isn't carrying real data. Also fixes a bio-to-rq
merge case.
- Don't re-set a bit on the buffer_head flags, if it's already set.
This can cause scalability concerns on bigger machines and
workloads. From Kemi Wang.
- Add BLK_STS_DEV_RESOURCE return value to blk-mq, allowing us to
distuingish between a local (device related) resource starvation
and a global one. The latter might happen without IO being in
flight, so it has to be handled a bit differently. From Ming"
* tag 'for-linus-20180204' of git://git.kernel.dk/linux-block:
block: skd: fix incorrect linux/slab_def.h inclusion
buffer: Avoid setting buffer bits that are already set
blk-mq-sched: Enable merging discard bio into request
blk-mq: fix discard merge with scheduler attached
blk-mq: introduce BLK_STS_DEV_RESOURCE
cache objects. This is good, but still leaves a lot of kernel memory
available to be copied to/from userspace in the face of bugs. To further
restrict what memory is available for copying, this creates a way to
whitelist specific areas of a given slab cache object for copying to/from
userspace, allowing much finer granularity of access control. Slab caches
that are never exposed to userspace can declare no whitelist for their
objects, thereby keeping them unavailable to userspace via dynamic copy
operations. (Note, an implicit form of whitelisting is the use of constant
sizes in usercopy operations and get_user()/put_user(); these bypass all
hardened usercopy checks since these sizes cannot change at runtime.)
This new check is WARN-by-default, so any mistakes can be found over the
next several releases without breaking anyone's system.
The series has roughly the following sections:
- remove %p and improve reporting with offset
- prepare infrastructure and whitelist kmalloc
- update VFS subsystem with whitelists
- update SCSI subsystem with whitelists
- update network subsystem with whitelists
- update process memory with whitelists
- update per-architecture thread_struct with whitelists
- update KVM with whitelists and fix ioctl bug
- mark all other allocations as not whitelisted
- update lkdtm for more sensible test overage
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
Comment: Kees Cook <kees@outflux.net>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=tzmJ
-----END PGP SIGNATURE-----
Merge tag 'usercopy-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull hardened usercopy whitelisting from Kees Cook:
"Currently, hardened usercopy performs dynamic bounds checking on slab
cache objects. This is good, but still leaves a lot of kernel memory
available to be copied to/from userspace in the face of bugs.
To further restrict what memory is available for copying, this creates
a way to whitelist specific areas of a given slab cache object for
copying to/from userspace, allowing much finer granularity of access
control.
Slab caches that are never exposed to userspace can declare no
whitelist for their objects, thereby keeping them unavailable to
userspace via dynamic copy operations. (Note, an implicit form of
whitelisting is the use of constant sizes in usercopy operations and
get_user()/put_user(); these bypass all hardened usercopy checks since
these sizes cannot change at runtime.)
This new check is WARN-by-default, so any mistakes can be found over
the next several releases without breaking anyone's system.
The series has roughly the following sections:
- remove %p and improve reporting with offset
- prepare infrastructure and whitelist kmalloc
- update VFS subsystem with whitelists
- update SCSI subsystem with whitelists
- update network subsystem with whitelists
- update process memory with whitelists
- update per-architecture thread_struct with whitelists
- update KVM with whitelists and fix ioctl bug
- mark all other allocations as not whitelisted
- update lkdtm for more sensible test overage"
* tag 'usercopy-v4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (38 commits)
lkdtm: Update usercopy tests for whitelisting
usercopy: Restrict non-usercopy caches to size 0
kvm: x86: fix KVM_XEN_HVM_CONFIG ioctl
kvm: whitelist struct kvm_vcpu_arch
arm: Implement thread_struct whitelist for hardened usercopy
arm64: Implement thread_struct whitelist for hardened usercopy
x86: Implement thread_struct whitelist for hardened usercopy
fork: Provide usercopy whitelisting for task_struct
fork: Define usercopy region in thread_stack slab caches
fork: Define usercopy region in mm_struct slab caches
net: Restrict unwhitelisted proto caches to size 0
sctp: Copy struct sctp_sock.autoclose to userspace using put_user()
sctp: Define usercopy region in SCTP proto slab cache
caif: Define usercopy region in caif proto slab cache
ip: Define usercopy region in IP proto slab cache
net: Define usercopy region in struct proto slab cache
scsi: Define usercopy region in scsi_sense_cache slab cache
cifs: Define usercopy region in cifs_request slab cache
vxfs: Define usercopy region in vxfs_inode slab cache
ufs: Define usercopy region in ufs_inode_cache slab cache
...
This is a set of three patches that depended on mq and zone changes in
the block tree (now upstream).
Signed-off-by: James E.J. Bottomley <jejb@linux.vnet.ibm.com>
-----BEGIN PGP SIGNATURE-----
iJwEABMIAEQWIQTnYEDbdso9F2cI+arnQslM7pishQUCWnSq/iYcamFtZXMuYm90
dG9tbGV5QGhhbnNlbnBhcnRuZXJzaGlwLmNvbQAKCRDnQslM7pishVRjAP4kVZ+d
o2gd6CqfhQqdbps7bcGdDCTjxTVZd4w56zgRAAEA4xjO6lhPCGlGEwJVlSMmojCE
rJuw2ITmWMX//V4iBmU=
=YQ8Y
-----END PGP SIGNATURE-----
Merge tag 'scsi-postmerge' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull second set of SCSI updates from James Bottomley:
"This is a set of three patches that depended on mq and zone changes in
the block tree (now upstream)"
* tag 'scsi-postmerge' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: sd: Remove zone write locking
scsi: sd_zbc: Initialize device request queue zoned data
scsi: scsi-mq-debugfs: Show more information
Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with reworks
to try to attempt to make the code easier to handle in the long run, but
no functional change. There's also some tree-wide sysfs attribute
fixups with lots of acks from the various subsystem maintainers, as well
as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWnLvPw8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ynNzACgkzjPoBytJWbpWFt6SR6L33/u4kEAnRFvVCGL
s6ygQPQhZIjKk2Lxa2hC
=Zihy
-----END PGP SIGNATURE-----
Merge tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core updates from Greg KH:
"Here is the set of "big" driver core patches for 4.16-rc1.
The majority of the work here is in the firmware subsystem, with
reworks to try to attempt to make the code easier to handle in the
long run, but no functional change. There's also some tree-wide sysfs
attribute fixups with lots of acks from the various subsystem
maintainers, as well as a handful of other normal fixes and changes.
And finally, some license cleanups for the driver core and sysfs code.
All have been in linux-next for a while with no reported issues"
* tag 'driver-core-4.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (48 commits)
device property: Define type of PROPERTY_ENRTY_*() macros
device property: Reuse property_entry_free_data()
device property: Move property_entry_free_data() upper
firmware: Fix up docs referring to FIRMWARE_IN_KERNEL
firmware: Drop FIRMWARE_IN_KERNEL Kconfig option
USB: serial: keyspan: Drop firmware Kconfig options
sysfs: remove DEBUG defines
sysfs: use SPDX identifiers
drivers: base: add coredump driver ops
sysfs: add attribute specification for /sysfs/devices/.../coredump
test_firmware: fix missing unlock on error in config_num_requests_store()
test_firmware: make local symbol test_fw_config static
sysfs: turn WARN() into pr_warn()
firmware: Fix a typo in fallback-mechanisms.rst
treewide: Use DEVICE_ATTR_WO
treewide: Use DEVICE_ATTR_RO
treewide: Use DEVICE_ATTR_RW
sysfs.h: Use octal permissions
component: add debugfs support
bus: simple-pm-bus: convert bool SIMPLE_PM_BUS to tristate
...
Xiaofei Tan