Long format options added, though the short ones should still work.
eg. the new "--Counter 0x10" is the same as the old "-C 0x10"
Note this Incompatibility:
Old:
-v displayed verbose debug output
New:
-v and --version simpaly display version
Additional parameters:
-d and --debug display verbose debug output
-h and --help display a help message
Updated turbosat.8 man page accordingly.
Signed-off-by: Len Brown <len.brown@intel.com>
Replaced previously open-coded Package C-state Limit decoding
with table-driven decoding. In doing so, updated to match January 2015
"Intel(R) 64 and IA-23 Architectures Software Developer's Manual".
In the past, turbostat would print package C-state residency columns
for all package states supported by the model's architecture, even though
a particular SKU may not support them, or they may be disabled by the BIOS.
Now turbostat will skip printing colunns if MSRs indicate that they are not enabled.
eg. many SKUs don't support PC7, and so that column will no longer be printed.
Signed-off-by: Len Brown <len.brown@intel.com>
While turbostat is significantly less useful on systems
with no APERF_MSR, it seems more friendly
to run on such systems and report what we can,
rather than refusing to run.
Update man page to reflect recent changes.
Signed-off-by: Len Brown <len.brown@intel.com>
Turbostat can be useful on systems that do not support invariant TSC,
so allow it to run on those systgems.
All arithmetic in turbostat using the TSC value is per-processsor,
so it does not depend on the TSC values being in sync acrosss processors.
Turbostat uses gettimeofday() for the measurement interval
rather than using the TSC directly, so that key metric
is also immune from variable TSC.
Turbostat prints a TSC sanity check column:
TSC_MHz = TSC_delta/interval
If this column is constant and is close to the processor
base frequency, then the TSC is behaving properly.
The other key turbostat columns are calculated this way:
Avg_Mhz = APERF_delta/interval
%Busy = MPERF_delta/TSC_delta
Bzy_MHz = TSC_delta/APERF_delta/MPERF_delta/interval
Tested on Core2 and Core2-Xeon, and so this patch includes
a few other changes to remove the assumption that target
systems are Nehalem and newer.
Signed-off-by: Len Brown <len.brown@intel.com>
The Processor generation code-named Haswell
added MSR_{CORE | GFX | RING}_PERF_LIMIT_REASONS
to explain when and how the processor limits frequency.
turbostat -v
will now decode these bits.
Each MSR has an "Active" set of bits which describe
current conditions, and a "Logged" set of bits,
which describe what has happened since last cleared.
Turbostat currently doesn't clear the log bits.
Signed-off-by: Len Brown <len.brown@intel.com>
For turbostat to run as non-root, it needs to permissions:
1. read access to /dev/cpu/*/msr
via standard user/group/world file permissions
2. CAP_SYS_RAWIO
eg. # setcap cap_sys_rawio=ep turbostat
Yes, running as root still works.
Signed-off-by: Len Brown <len.brown@intel.com>
The Intel 64 and IA-32 Architectures Software Developer's Manual says
that TjMax is stored in bits 23:16 of MSR_TEMPERATURE TARGET (0x1a2).
That's 8 bits, not 7, so it must be masked with 0xFF rather than 0x7F.
The manual has no mention of which values should be considered valid,
which kind of implies that they all are. Arbitrarily discarding values
outside a specific range is wrong. The upper range check had to be
fixed recently (commit 144b44b1) and the lower range check is just as
wrong. See bug #75071:
https://bugzilla.kernel.org/show_bug.cgi?id=75071
There are many Xeon processor series with TjMax of 70, 71 or 80
degrees Celsius, way below the arbitrary 85 degrees Celsius limit.
There may be other (past or future) models with even lower limits.
So drop this arbitrary check. The only value that would be clearly
invalid is 0. Everything else should be accepted.
After these changes, turbostat is aligned with what the coretemp
driver does.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Len Brown <len.brown@intel.com>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Use 8 columns for each number ouput.
We don't fit into 80 columns on most machines,
so keep the format simple.
Print frequency in MHz instead of GHz.
We've got 8 columns now, so use them to
show low frequency in a more natural unit.
Many users didn't understand what %c0 meant,
so re-name it to be %Busy.
Add Avg_MHz column, which is the frequency that many
users expect to see -- the total number of cycles executed
over the measurement interval.
People found the previous GHz to be confusing, since
it was the speed only over the non-idle interval.
That measurement has been re-named Bzy_MHz.
Suggested-by: Dirk J. Brandewie
Signed-off-by: Len Brown <len.brown@intel.com>
The new option allows just run turbostat and get dump of counter values. It's
useful when we have something more than one program to test.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The -s is not used, let's remove it, and update quick help accordingly.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Add "-J" option to report energy consumed in joules per sample. This option
also adds the sample time to the reported values.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Haswell Xeon has slightly different RAPL support than client HSW,
which prevented the previous version of turbostat from running on HSX.
Signed-off-by: Len Brown <len.brown@intel.com>
Most of turbostat's error handling consists of printing an error (often
including an errno) and exiting. Since perror doesn't support a format
string, those error messages are often ambiguous, such as just showing a
file path, which doesn't uniquely identify which call failed.
turbostat already uses _GNU_SOURCE, so switch to the err and errx
functions from err.h, which take a format string.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Several different functions in turbostat contain the same pattern of
opening a file and exiting on failure. Factor out a common fopen_or_die
function for that.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Many different chunks of code in turbostat open a file, parse a single
int out of it, and close it. Factor that out into a common function.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Len Brown <len.brown@intel.com>
Some systems declare fscanf with the warn_unused_result attribute. On
such systems, turbostat generates the following warnings:
turbostat.c: In function 'get_core_id':
turbostat.c:1203:8: warning: ignoring return value of 'fscanf', declared with attribute warn_unused_result [-Wunused-result]
turbostat.c: In function 'get_physical_package_id':
turbostat.c:1186:8: warning: ignoring return value of 'fscanf', declared with attribute warn_unused_result [-Wunused-result]
turbostat.c: In function 'cpu_is_first_core_in_package':
turbostat.c:1169:8: warning: ignoring return value of 'fscanf', declared with attribute warn_unused_result [-Wunused-result]
turbostat.c: In function 'cpu_is_first_sibling_in_core':
turbostat.c:1148:8: warning: ignoring return value of 'fscanf', declared with attribute warn_unused_result [-Wunused-result]
Fix these by checking the return value of those four calls to fscanf.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Len Brown <len.brown@intel.com>
turbostat uses inline assembly to call cpuid. On 32-bit x86, on systems
that have certain security features enabled by default that make -fPIC
the default, this causes a build error:
turbostat.c: In function ‘check_cpuid’:
turbostat.c:1906:2: error: PIC register clobbered by ‘ebx’ in ‘asm’
asm("cpuid" : "=a" (fms), "=c" (ecx), "=d" (edx) : "a" (1) : "ebx");
^
GCC provides a header cpuid.h, containing a __get_cpuid function that
works with both PIC and non-PIC. (On PIC, it saves and restores ebx
around the cpuid instruction.) Use that instead.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Cc: stable@vger.kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
turbostat uses the format %zx to print an off_t. However, %zx wants a
size_t, not an off_t. On 32-bit targets, those refer to different
types, potentially even with different sizes. Use %llx and a cast
instead, since printf does not have a length modifier for off_t.
Without this patch, when compiling for a 32-bit target:
turbostat.c: In function 'get_msr':
turbostat.c:231:3: warning: format '%zx' expects argument of type 'size_t', but argument 4 has type 'off_t' [-Wformat]
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Signed-off-by: Len Brown <len.brown@intel.com>
turbostat's Makefile puts arch/x86/include/uapi/ in the include path, so
that it can include <asm/msr.h> from it. It isn't in general safe to
include even uapi headers directly from the kernel tree without
processing them through scripts/headers_install.sh, but asm/msr.h
happens to work.
However, that include path can break with some versions of system
headers, by overriding some system headers with the unprocessed versions
directly from the kernel source. For instance:
In file included from /build/x86-generic/usr/include/bits/sigcontext.h:28:0,
from /build/x86-generic/usr/include/signal.h:339,
from /build/x86-generic/usr/include/sys/wait.h:31,
from turbostat.c:27:
../../../../arch/x86/include/uapi/asm/sigcontext.h:4:28: fatal error: linux/compiler.h: No such file or directory
This occurs because the system bits/sigcontext.h on that build system
includes <asm/sigcontext.h>, and asm/sigcontext.h in the kernel source
includes <linux/compiler.h>, which scripts/headers_install.sh would have
filtered out.
Since turbostat really only wants a single header, just include that one
header rather than putting an entire directory of kernel headers on the
include path.
In the process, switch from msr.h to msr-index.h, since turbostat just
wants the MSR numbers.
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Cc: stable@vger.kernel.org
Signed-off-by: Len Brown <len.brown@intel.com>
Support the next generation Intel Atom processor
mirco-architecture, formerly called Silvermont.
The server version, formerly called "Avoton",
is named the "Intel(R) Atom(TM) Processor C2000 Product Family".
The client version, formerly called "Bay Trail",
is named the "Intel Atom Processor Z3000 Series",
as well as various "Intel Pentium Processor"
and "Intel Celeron Processor" brands, depending
on form-factor.
Silvermont has a set of MSRs not far off from NHM,
but the RAPL register set is a sub-set of those previously supported.
Signed-off-by: Len Brown <len.brown@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On platforms with C8-C10 support, the additional C-states cause
turbostat to overrun its output buffer of 128 bytes per CPU. Increase
this to 256 bytes per CPU.
[ As a bugfix, this should go into 3.10; however, since the C8-C10
support didn't go in until after 3.9, this need not go into any stable
kernel. ]
Signed-off-by: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <len.brown@intel.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Display residency in the new C-states, C8, C9, C10.
C8, C9, C10 are present on some:
"Fourth Generation Intel(R) Core(TM) Processors",
which are based on Intel(R) microarchitecture code name Haswell.
Signed-off-by: Kristen Carlson Accardi <kristen@linux.intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The SMI counter is popular -- so display it by default
rather than requiring an option. What the heck,
we've blown the 80 column budget on many systems already...
Note that the value displayed is the delta
during the measurement interval.
The absolute value of the counter can still be seen with
the generic 32-bit MSR option, ie. -m 0x34
Signed-off-by: Len Brown <len.brown@intel.com>
When verbose is enabled, print the C1E-Enable
bit in MSR_IA32_POWER_CTL.
also delete some redundant tests on the verbose variable.
Signed-off-by: Len Brown <len.brown@intel.com>
This patch enables turbostat to run properly on the
next-generation Intel(R) Microarchitecture, code named "Haswell" (HSW).
HSW supports the BCLK and counters found in SNB.
Signed-off-by: Len Brown <len.brown@intel.com>
Pull powertool update from Len Brown:
"This updates the tree w/ the latest version of turbostat, which
reports temperature and - on SNB and later - Watts."
Fix up semantic merge conflict as per Len.
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
tools: Allow tools to be installed in a user specified location
tools/power: turbostat: make Makefile a bit more capable
tools/power x86_energy_perf_policy: close /proc/stat in for_every_cpu()
tools/power turbostat: v3.0: monitor Watts and Temperature
tools/power turbostat: fix output buffering issue
tools/power turbostat: prevent infinite loop on migration error path
x86 power: define RAPL MSRs
tools/power/x86/turbostat: share kernel MSR #defines
When building x86_energy_perf_policy or turbostat within the confines of
a packaging system such as RPM, we need to be able to have it install to
the buildroot and not the root filesystem of the build machine. This
adds a DESTDIR variable that when set will act as a prefix for the
install location of these tools.
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The turbostat Makefile is pretty simple, its output is placed in the
same directory as the source, the install rule has no concept of a
prefix or sysroot, and you can set CC to use a specific compiler but
not use the more familiar CROSS_COMPILE. By making a few minor changes
these limitations are removed while leaving the default behavior
matching what it used to be.
Example build with these changes:
make CROSS_COMPILE=i686-wrs-linux-gnu- DESTDIR=/tmp install
or from the tools directory
make CROSS_COMPILE=i686-wrs-linux-gnu- DESTDIR=/tmp turbostat_install
Signed-off-by: Mark Asselstine <mark.asselstine@windriver.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Instead of returning out of for_every_cpu() we should break out of the loop=
which will then tidy up correctly by closing the file /proc/stat.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Show power in Watts and temperature in Celsius
when hardware support is present.
Intel's Sandy Bridge and Ivy Bridge processor generations support RAPL
(Run-Time-Average-Power-Limiting). Per the Intel SDM
(Intel® 64 and IA-32 Architectures Software Developer Manual)
RAPL provides hardware energy counters and power control MSRs
(Model Specific Registers). RAPL MSRs are designed primarily
as a method to implement power capping. However, they are useful
for monitoring system power whether or not power capping is used.
In addition, Turbostat now shows temperature from DTS
(Digital Thermal Sensor) and PTM (Package Thermal Monitor) hardware,
if present.
As before, turbostat reads MSRs, and never writes MSRs.
New columns are present in turbostat output:
The Pkg_W column shows Watts for each package (socket) in the system.
On multi-socket systems, the system summary on the 1st row shows the sum
for all sockets together.
The Cor_W column shows Watts due to processors cores.
Note that Core_W is included in Pkg_W.
The optional GFX_W column shows Watts due to the graphics "un-core".
Note that GFX_W is included in Pkg_W.
The optional RAM_W column on server processors shows Watts due to DRAM DIMMS.
As DRAM DIMMs are outside the processor package, RAM_W is not included in Pkg_W.
The optional PKG_% and RAM_% columns on server processors shows the % of time
in the measurement interval that RAPL power limiting is in effect on the
package and on DRAM.
Note that the RAPL energy counters have some limitations.
First, hardware updates the counters about once every milli-second.
This is fine for typical turbostat measurement intervals > 1 sec.
However, when turbostat is used to measure events that approach
1ms, the counters are less useful.
Second, the 32-bit energy counters are subject to wrapping.
For example, a counter incrementing 15 micro-Joule units
on a 130 Watt TDP server processor could (in theory)
roll over in about 9 minutes. Turbostat detects and handles
up to 1 counter overflow per measurement interval.
But when the measurement interval exceeds the guaranteed
counter range, we can't detect if more than 1 overflow occured.
So in this case turbostat indicates that the results are
in question by replacing the fractional part of the Watts
in the output with "**":
Pkg_W Cor_W GFX_W
3** 0** 0**
Third, the RAPL counters are energy (Joule) counters -- they sum up
weighted events in the package to estimate energy consumed. They are
not analong power (Watt) meters. In practice, they tend to under-count
because they don't cover every possible use of energy in the package.
The accuracy of the RAPL counters will vary between product generations,
and between SKU's in the same product generation, and with temperature.
turbostat's -v (verbose) option now displays more power and thermal configuration
information -- as shown on the turbostat.8 manual page.
For example, it now displays the Package and DRAM Thermal Design Power (TDP):
cpu0: MSR_PKG_POWER_INFO: 0x2f064001980410 (130 W TDP, RAPL 51 - 200 W, 0.045898 sec.)
cpu0: MSR_DRAM_POWER_INFO,: 0x28025800780118 (35 W TDP, RAPL 15 - 75 W, 0.039062 sec.)
cpu8: MSR_PKG_POWER_INFO: 0x2f064001980410 (130 W TDP, RAPL 51 - 200 W, 0.045898 sec.)
cpu8: MSR_DRAM_POWER_INFO,: 0x28025800780118 (35 W TDP, RAPL 15 - 75 W, 0.039062 sec.)
Signed-off-by: Len Brown <len.brown@intel.com>
In periodic mode, turbostat writes to stdout,
but users were un-able to re-direct stdout, eg.
turbostat > outputfile
would result in an empty outputfile.
Signed-off-by: Len Brown <len.brown@intel.com>
Turbostat assumed if it can't migrate to a CPU, then the CPU
must have gone off-line and turbostat should re-initialize
with the new topology.
But if turbostat can not migrate because it is restricted by
a cpuset, then it will fail to migrate even after re-initialization,
resulting in an infinite loop.
Spit out a warning when we can't migrate
and endure only 2 re-initialize cycles in a row
before giving up and exiting.
Signed-off-by: Len Brown <len.brown@intel.com>
Now that turbostat is built in the kernel tree,
it can share MSR #defines with the kernel.
Signed-off-by: Len Brown <len.brown@intel.com>
Cc: x86@kernel.org
Counting SMIs is popular, so add a dedicated "-s" option to do it,
and juggle some of the other option letters.
-S is now system summary (was -s)
-c is 32 bit counter (was -d)
-C is 64-bit counter (was -D)
-p is 1st thread in core (was -c)
-P is 1st thread in package (was -p)
bump the minor version number
Signed-off-by: Len Brown <len.brown@intel.com>
# turbostat -d 0x34
is useful for printing the number of SMI's within an interval
on Nehalem and newer processors.
where
# turbostat -m 0x34
will simply print out the total SMI count since reset.
Suggested-by: Andi Kleen
Signed-off-by: Len Brown <len.brown@intel.com>
The -M option dumps the specified 64-bit MSR with every sample.
Previously it was output at the end of each line.
However, with the v2 style of printing, the lines are now staggered,
making MSR output hard to read.
So move the MSR output column to the left where things are aligned.
Signed-off-by: Len Brown <len.brown@intel.com>
The "turbo-limit" is the maximum opportunistic processor
speed, assuming no electrical or thermal constraints.
For a given processor, the turbo-limit varies, depending
on the number of active cores. Generally, there is more
opportunity when fewer cores are active.
Under the "-v" verbose option, turbostat would
print the turbo-limits for the four cases
of 1 to 4 cores active.
Expand that capability to cover the cases of turbo
opportunities with up to 16 cores active.
Note that not all hardware platforms supply this information,
and that sometimes a valid limit may be specified for
a core which is not actually present.
Signed-off-by: Len Brown <len.brown@intel.com>
Under some conditions, c1% was displayed as very large number,
much higher than 100%.
c1% is not measured, it is derived as "that, which is left over"
from other counters. However, the other counters are not collected
atomically, and so it is possible for c1% to be calaculagted as
a small negative number -- displayed as very large positive.
There was a check for mperf vs tsc for this already,
but it needed to also include the other counters
that are used to calculate c1.
Signed-off-by: Len Brown <len.brown@intel.com>
Measuring large profoundly-idle configurations
requires turbostat to be more lightweight.
Otherwise, the operation of turbostat itself
can interfere with the measurements.
This re-write makes turbostat topology aware.
Hardware is accessed in "topology order".
Redundant hardware accesses are deleted.
Redundant output is deleted.
Also, output is buffered and
local RDTSC use replaces remote MSR access for TSC.
From a feature point of view, the output
looks different since redundant figures are absent.
Also, there are now -c and -p options -- to restrict
output to the 1st thread in each core, and the 1st
thread in each package, respectively. This is helpful
to reduce output on big systems, where more detail
than the "-s" system summary is desired.
Finally, periodic mode output is now on stdout, not stderr.
Turbostat v2 is also slightly more robust in
handling run-time CPU online/offline events,
as it now checks the actual map of on-line cpus rather
than just the total number of on-line cpus.
Signed-off-by: Len Brown <len.brown@intel.com>
Initial IVB support went into turbostat in Linux-3.1:
553575f1ae
(tools turbostat: recognize and run properly on IVB)
However, when running on IVB, turbostat would fail
to report the new couters added with SNB, c7, pc2 and pc7.
So in scenarios where these counters are non-zero on IVB,
turbostat would report erroneous residencey results.
In particular c7 time would be added to c1 time,
since c1 time is calculated as "that which is left over".
Also, turbostat reports MHz capabilities when passed
the "-v" option, and it would incorrectly report 133MHz
bclk instead of 100MHz bclk for IVB, which would inflate
GHz reported with that option.
This patch is a backport of a fix already included in turbostat v2.
Signed-off-by: Len Brown <len.brown@intel.com>
Len Brown