Currently after setting tap0 link up, the tun code wakes tx/rx waited
queues up in tun_net_open() when .ndo_open() is called, however the
IFF_UP flag has not been set yet. If there's already a wait queue, it
would fail to transmit when checking the IFF_UP flag in tun_sendmsg().
Then the saving vhost_poll_start() will add the wq into wqh until it
is waken up again. Although this works when IFF_UP flag has been set
when tun_chr_poll detects; this is not true if IFF_UP flag has not
been set at that time. Sadly the latter case is a fatal error, as
the wq will never be waken up in future unless later manually
setting link up on purpose.
Fix this by moving the wakeup process into the NETDEV_UP event
notifying process, this makes sure IFF_UP has been set before all
waited queues been waken up.
Signed-off-by: Fei Li <lifei.shirley@bytedance.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In sock_getsockopt(), 'optlen' is fetched the first time from userspace.
'len < 0' is then checked. Then in condition 'SO_MEMINFO', 'optlen' is
fetched the second time from userspace.
If change it between two fetches may cause security problems or unexpected
behaivor, and there is no reason to fetch it a second time.
To fix this, we need to remove the second fetch.
Signed-off-by: JingYi Hou <houjingyi647@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears that a FAILOVER_MSG can come from peer even when the failure
link is resetting (i.e. just after the 'node_write_unlock()'...). This
means the failover procedure on the node has not been started yet.
The situation is as follows:
node1 node2
linkb linka linka linkb
| | | |
| | x failure |
| | RESETTING |
| | | |
| x failure RESET |
| RESETTING FAILINGOVER |
| | (FAILOVER_MSG) | |
|<-------------------------------------------------|
| *FAILINGOVER | | |
| | (dummy FAILOVER_MSG) | |
|------------------------------------------------->|
| RESET | | FAILOVER_END
| FAILINGOVER RESET |
. . . .
. . . .
. . . .
Once this happens, the link failover procedure will be triggered
wrongly on the receiving node since the node isn't in FAILINGOVER state
but then another link failover will be carried out.
The consequences are:
1) A peer might get stuck in FAILINGOVER state because the 'sync_point'
was set, reset and set incorrectly, the criteria to end the failover
would not be met, it could keep waiting for a message that has already
received.
2) The early FAILOVER_MSG(s) could be queued in the link failover
deferdq but would be purged or not pulled out because the 'drop_point'
was not set correctly.
3) The early FAILOVER_MSG(s) could be dropped too.
4) The dummy FAILOVER_MSG could make the peer leaving FAILINGOVER state
shortly, but later on it would be restarted.
The same situation can also happen when the link is in PEER_RESET state
and a FAILOVER_MSG arrives.
The commit resolves the issues by forcing the link down immediately, so
the failover procedure will be started normally (which is the same as
when receiving a FAILOVER_MSG and the link is in up state).
Also, the function "tipc_node_link_failover()" is toughen to avoid such
a situation from happening.
Acked-by: Jon Maloy <jon.maloy@ericsson.se>
Signed-off-by: Tuong Lien <tuong.t.lien@dektech.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some transceivers may comply with SFF-8472 even though they do not
implement the Digital Diagnostic Monitoring (DDM) interface described in
the spec. The existence of such area is specified by the 6th bit of byte
92, set to 1 if implemented.
Currently, without checking this bit, bnx2x fails trying to read sfp
module's EEPROM with the follow message:
ethtool -m enP5p1s0f1
Cannot get Module EEPROM data: Input/output error
Because it fails to read the additional 256 bytes in which it is assumed
to exist the DDM data.
This issue was noticed using a Mellanox Passive DAC PN 01FT738. The EEPROM
data was confirmed by Mellanox as correct and similar to other Passive
DACs from other manufacturers.
Signed-off-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Acked-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull vfs fixes from Al Viro:
"MS_MOVE regression fix + breakage in fsmount(2) (also introduced in
this cycle, along with fsmount(2) itself).
I'm still digging through the piles of mail, so there might be more
fixes to follow, but these two are obvious and self-contained, so
there's no point delaying those..."
* 'fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
fs/namespace: fix unprivileged mount propagation
vfs: fsmount: add missing mntget()
Pull networking fixes from David Miller:
"Lots of bug fixes here:
1) Out of bounds access in __bpf_skc_lookup, from Lorenz Bauer.
2) Fix rate reporting in cfg80211_calculate_bitrate_he(), from John
Crispin.
3) Use after free in psock backlog workqueue, from John Fastabend.
4) Fix source port matching in fdb peer flow rule of mlx5, from Raed
Salem.
5) Use atomic_inc_not_zero() in fl6_sock_lookup(), from Eric Dumazet.
6) Network header needs to be set for packet redirect in nfp, from
John Hurley.
7) Fix udp zerocopy refcnt, from Willem de Bruijn.
8) Don't assume linear buffers in vxlan and geneve error handlers,
from Stefano Brivio.
9) Fix TOS matching in mlxsw, from Jiri Pirko.
10) More SCTP cookie memory leak fixes, from Neil Horman.
11) Fix VLAN filtering in rtl8366, from Linus Walluij.
12) Various TCP SACK payload size and fragmentation memory limit fixes
from Eric Dumazet.
13) Use after free in pneigh_get_next(), also from Eric Dumazet.
14) LAPB control block leak fix from Jeremy Sowden"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (145 commits)
lapb: fixed leak of control-blocks.
tipc: purge deferredq list for each grp member in tipc_group_delete
ax25: fix inconsistent lock state in ax25_destroy_timer
neigh: fix use-after-free read in pneigh_get_next
tcp: fix compile error if !CONFIG_SYSCTL
hv_sock: Suppress bogus "may be used uninitialized" warnings
be2net: Fix number of Rx queues used for flow hashing
net: handle 802.1P vlan 0 packets properly
tcp: enforce tcp_min_snd_mss in tcp_mtu_probing()
tcp: add tcp_min_snd_mss sysctl
tcp: tcp_fragment() should apply sane memory limits
tcp: limit payload size of sacked skbs
Revert "net: phylink: set the autoneg state in phylink_phy_change"
bpf: fix nested bpf tracepoints with per-cpu data
bpf: Fix out of bounds memory access in bpf_sk_storage
vsock/virtio: set SOCK_DONE on peer shutdown
net: dsa: rtl8366: Fix up VLAN filtering
net: phylink: set the autoneg state in phylink_phy_change
net: add high_order_alloc_disable sysctl/static key
tcp: add tcp_tx_skb_cache sysctl
...
When propagating mounts across mount namespaces owned by different user
namespaces it is not possible anymore to move or umount the mount in the
less privileged mount namespace.
Here is a reproducer:
sudo mount -t tmpfs tmpfs /mnt
sudo --make-rshared /mnt
# create unprivileged user + mount namespace and preserve propagation
unshare -U -m --map-root --propagation=unchanged
# now change back to the original mount namespace in another terminal:
sudo mkdir /mnt/aaa
sudo mount -t tmpfs tmpfs /mnt/aaa
# now in the unprivileged user + mount namespace
mount --move /mnt/aaa /opt
Unfortunately, this is a pretty big deal for userspace since this is
e.g. used to inject mounts into running unprivileged containers.
So this regression really needs to go away rather quickly.
The problem is that a recent change falsely locked the root of the newly
added mounts by setting MNT_LOCKED. Fix this by only locking the mounts
on copy_mnt_ns() and not when adding a new mount.
Fixes: 3bd045cc9c ("separate copying and locking mount tree on cross-userns copies")
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <stable@vger.kernel.org>
Tested-by: Christian Brauner <christian@brauner.io>
Acked-by: Christian Brauner <christian@brauner.io>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Christian Brauner <christian@brauner.io>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
sys_fsmount() needs to take a reference to the new mount when adding it
to the anonymous mount namespace. Otherwise the filesystem can be
unmounted while it's still in use, as found by syzkaller.
Reported-by: Mark Rutland <mark.rutland@arm.com>
Reported-by: syzbot+99de05d099a170867f22@syzkaller.appspotmail.com
Reported-by: syzbot+7008b8b8ba7df475fdc8@syzkaller.appspotmail.com
Fixes: 93766fbd26 ("vfs: syscall: Add fsmount() to create a mount for a superblock")
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Eric Dumazet says:
====================
tcp: make sack processing more robust
Jonathan Looney brought to our attention multiple problems
in TCP stack at the sender side.
SACK processing can be abused by malicious peers to either
cause overflows, or increase of memory usage.
First two patches fix the immediate problems.
Since the malicious peers abuse senders by advertizing a very
small MSS in their SYN or SYNACK packet, the last two
patches add a new sysctl so that admins can chose a higher
limit for MSS clamping.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This tag contains fixes, defconfig, and DT data changes for the v5.2-rc
series. The fixes are relatively straightforward:
- Addition of a TLB fence in the vmalloc_fault path, so the CPU doesn't
enter an infinite page fault loop;
- Readdition of the pm_power_off export, so device drivers that
reassign it can now be built as modules;
- A udelay() fix for RV32, fixing a miscomputation of the delay time;
- Removal of deprecated smp_mb__*() barriers.
The tag also adds initial DT data infrastructure for arch/riscv, along
with initial data for the SiFive FU540-C000 SoC and the corresponding
HiFive Unleashed board.
We also update the RV64 defconfig to include some core drivers for the
FU540 in the build.
-----BEGIN PGP SIGNATURE-----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=aotJ
-----END PGP SIGNATURE-----
Merge tag 'riscv-for-v5.2/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux
Pull RISC-V fixes from Paul Walmsley:
"This contains fixes, defconfig, and DT data changes for the v5.2-rc
series.
The fixes are relatively straightforward:
- Addition of a TLB fence in the vmalloc_fault path, so the CPU
doesn't enter an infinite page fault loop
- Readdition of the pm_power_off export, so device drivers that
reassign it can now be built as modules
- A udelay() fix for RV32, fixing a miscomputation of the delay time
- Removal of deprecated smp_mb__*() barriers
This also adds initial DT data infrastructure for arch/riscv, along
with initial data for the SiFive FU540-C000 SoC and the corresponding
HiFive Unleashed board.
We also update the RV64 defconfig to include some core drivers for the
FU540 in the build"
* tag 'riscv-for-v5.2/fixes-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/riscv/linux:
riscv: remove unused barrier defines
riscv: mm: synchronize MMU after pte change
riscv: dts: add initial board data for the SiFive HiFive Unleashed
riscv: dts: add initial support for the SiFive FU540-C000 SoC
dt-bindings: riscv: convert cpu binding to json-schema
dt-bindings: riscv: sifive: add YAML documentation for the SiFive FU540
arch: riscv: add support for building DTB files from DT source data
riscv: Fix udelay in RV32.
riscv: export pm_power_off again
RISC-V: defconfig: enable clocks, serial console
They were introduced in commit fab957c11e ("RISC-V: Atomic and
Locking Code") long after commit 2e39465abc ("locking: Remove
deprecated smp_mb__() barriers") removed the remnants of all previous
instances from the tree.
Signed-off-by: Rolf Eike Beer <eb@emlix.com>
[paul.walmsley@sifive.com: stripped spurious mbox header from patch
description; fixed commit references in patch header]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Because RISC-V compliant implementations can cache invalid entries
in TLB, an SFENCE.VMA is necessary after changes to the page table.
This patch adds an SFENCE.vma for the vmalloc_fault path.
Signed-off-by: ShihPo Hung <shihpo.hung@sifive.com>
[paul.walmsley@sifive.com: reversed tab->whitespace conversion,
wrapped comment lines]
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: linux-riscv@lists.infradead.org
Cc: stable@vger.kernel.org
Add initial board data for the SiFive HiFive Unleashed A00.
Currently the data populated in this DT file describes the board
DRAM configuration and the external clock sources that supply the
PRCI.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Loys Ollivier <lollivier@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Antony Pavlov <antonynpavlov@gmail.com>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Add initial support for the SiFive FU540-C000 SoC. This is a 28nm SoC
based around the SiFive U54-MC core complex and a TileLink
interconnect.
This file is expected to grow as more device drivers are added to the
kernel.
This patch includes a fix to the QSPI memory map due to a
documentation bug, found by ShihPo Hung <shihpo.hung@sifive.com>, adds
entries for the I2C controller, and merges all DT changes that
formerly were made dynamically by the riscv-pk BBL proxy kernel.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Loys Ollivier <lollivier@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: ShihPo Hung <shihpo.hung@sifive.com>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
At Rob's request, we're starting to migrate our DT binding
documentation to json-schema YAML format. Start by converting our cpu
binding documentation. While doing so, document more properties and
nodes. This includes adding binding documentation support for the E51
and U54 CPU cores ("harts") that are present on this SoC. These cores
are described in:
https://static.dev.sifive.com/FU540-C000-v1.0.pdf
This cpus.yaml file is intended to be a starting point and to
evolve over time. It passes dt-doc-validate as of the yaml-bindings
commit 4c79d42e9216.
This patch was originally based on the ARM json-schema binding
documentation as added by commit 672951cbd1 ("dt-bindings: arm: Convert
cpu binding to json-schema").
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Add YAML DT binding documentation for the SiFive FU540 SoC. This
SoC is documented at:
https://static.dev.sifive.com/FU540-C000-v1.0.pdf
Passes dt-doc-validate, as of yaml-bindings commit 4c79d42e9216.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: devicetree@vger.kernel.org
Cc: linux-riscv@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Similar to ARM64, add support for building DTB files from DT source
data for RISC-V boards.
This patch starts with the infrastructure needed for SiFive boards.
Boards from other vendors would add support here in a similar form.
Signed-off-by: Paul Walmsley <paul.walmsley@sifive.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Loys Ollivier <lollivier@baylibre.com>
Tested-by: Kevin Hilman <khilman@baylibre.com>
Cc: Palmer Dabbelt <palmer@sifive.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
lapb_register calls lapb_create_cb, which initializes the control-
block's ref-count to one, and __lapb_insert_cb, which increments it when
adding the new block to the list of blocks.
lapb_unregister calls __lapb_remove_cb, which decrements the ref-count
when removing control-block from the list of blocks, and calls lapb_put
itself to decrement the ref-count before returning.
However, lapb_unregister also calls __lapb_devtostruct to look up the
right control-block for the given net_device, and __lapb_devtostruct
also bumps the ref-count, which means that when lapb_unregister returns
the ref-count is still 1 and the control-block is leaked.
Call lapb_put after __lapb_devtostruct to fix leak.
Reported-by: syzbot+afb980676c836b4a0afa@syzkaller.appspotmail.com
Signed-off-by: Jeremy Sowden <jeremy@azazel.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Syzbot reported a memleak caused by grp members' deferredq list not
purged when the grp is be deleted.
The issue occurs when more(msg_grp_bc_seqno(hdr), m->bc_rcv_nxt) in
tipc_group_filter_msg() and the skb will stay in deferredq.
So fix it by calling __skb_queue_purge for each member's deferredq
in tipc_group_delete() when a tipc sk leaves the grp.
Fixes: b87a5ea31c ("tipc: guarantee group unicast doesn't bypass group broadcast")
Reported-by: syzbot+78fbe679c8ca8d264a8d@syzkaller.appspotmail.com
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_tx_skb_cache_key and tcp_rx_skb_cache_key must be available
even if CONFIG_SYSCTL is not set.
Fixes: 0b7d7f6b22 ("tcp: add tcp_tx_skb_cache sysctl")
Fixes: ede61ca474 ("tcp: add tcp_rx_skb_cache sysctl")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
gcc 8.2.0 may report these bogus warnings under some condition:
warning: ‘vnew’ may be used uninitialized in this function
warning: ‘hvs_new’ may be used uninitialized in this function
Actually, the 2 pointers are only initialized and used if the variable
"conn_from_host" is true. The code is not buggy here.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Number of Rx queues used for flow hashing returned by the driver is
incorrect and this bug prevents user to use the last Rx queue in
indirection table.
Let's say we have a NIC with 6 combined queues:
[root@sm-03 ~]# ethtool -l enp4s0f0
Channel parameters for enp4s0f0:
Pre-set maximums:
RX: 5
TX: 5
Other: 0
Combined: 6
Current hardware settings:
RX: 0
TX: 0
Other: 0
Combined: 6
Default indirection table maps all (6) queues equally but the driver
reports only 5 rings available.
[root@sm-03 ~]# ethtool -x enp4s0f0
RX flow hash indirection table for enp4s0f0 with 5 RX ring(s):
0: 0 1 2 3 4 5 0 1
8: 2 3 4 5 0 1 2 3
16: 4 5 0 1 2 3 4 5
24: 0 1 2 3 4 5 0 1
...
Now change indirection table somehow:
[root@sm-03 ~]# ethtool -X enp4s0f0 weight 1 1
[root@sm-03 ~]# ethtool -x enp4s0f0
RX flow hash indirection table for enp4s0f0 with 6 RX ring(s):
0: 0 0 0 0 0 0 0 0
...
64: 1 1 1 1 1 1 1 1
...
Now it is not possible to change mapping back to equal (default) state:
[root@sm-03 ~]# ethtool -X enp4s0f0 equal 6
Cannot set RX flow hash configuration: Invalid argument
Fixes: 594ad54a2c ("be2net: Add support for setting and getting rx flow hash options")
Reported-by: Tianhao <tizhao@redhat.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When stack receives pkt: [802.1P vlan 0][802.1AD vlan 100][IPv4],
vlan_do_receive() returns false if it does not find vlan_dev. Later
__netif_receive_skb_core() fails to find packet type handler for
skb->protocol 801.1AD and drops the packet.
801.1P header with vlan id 0 should be handled as untagged packets.
This patch fixes it by checking if vlan_id is 0 and processes next vlan
header.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull x86 fixes from Thomas Gleixner:
"The accumulated fixes from this and last week:
- Fix vmalloc TLB flush and map range calculations which lead to
stale TLBs, spurious faults and other hard to diagnose issues.
- Use fault_in_pages_writable() for prefaulting the user stack in the
FPU code as it's less fragile than the current solution
- Use the PF_KTHREAD flag when checking for a kernel thread instead
of current->mm as the latter can give the wrong answer due to
use_mm()
- Compute the vmemmap size correctly for KASLR and 5-Level paging.
Otherwise this can end up with a way too small vmemmap area.
- Make KASAN and 5-level paging work again by making sure that all
invalid bits are masked out when computing the P4D offset. This
worked before but got broken recently when the LDT remap area was
moved.
- Prevent a NULL pointer dereference in the resource control code
which can be triggered with certain mount options when the
requested resource is not available.
- Enforce ordering of microcode loading vs. perf initialization on
secondary CPUs. Otherwise perf tries to access a non-existing MSR
as the boot CPU marked it as available.
- Don't stop the resource control group walk early otherwise the
control bitmaps are not updated correctly and become inconsistent.
- Unbreak kgdb by returning 0 on success from
kgdb_arch_set_breakpoint() instead of an error code.
- Add more Icelake CPU model defines so depending changes can be
queued in other trees"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/microcode, cpuhotplug: Add a microcode loader CPU hotplug callback
x86/kasan: Fix boot with 5-level paging and KASAN
x86/fpu: Don't use current->mm to check for a kthread
x86/kgdb: Return 0 from kgdb_arch_set_breakpoint()
x86/resctrl: Prevent NULL pointer dereference when local MBM is disabled
x86/resctrl: Don't stop walking closids when a locksetup group is found
x86/fpu: Update kernel's FPU state before using for the fsave header
x86/mm/KASLR: Compute the size of the vmemmap section properly
x86/fpu: Use fault_in_pages_writeable() for pre-faulting
x86/CPU: Add more Icelake model numbers
mm/vmalloc: Avoid rare case of flushing TLB with weird arguments
mm/vmalloc: Fix calculation of direct map addr range
Pull timer fixes from Thomas Gleixner:
"A set of small fixes:
- Repair the ktime_get_coarse() functions so they actually deliver
what they are supposed to: tick granular time stamps. The current
code missed to add the accumulated nanoseconds part of the
timekeeper so the resulting granularity was 1 second.
- Prevent the tracer from infinitely recursing into time getter
functions in the arm architectured timer by marking these functions
notrace
- Fix a trivial compiler warning caused by wrong qualifier ordering"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping: Repair ktime_get_coarse*() granularity
clocksource/drivers/arm_arch_timer: Don't trace count reader functions
clocksource/drivers/timer-ti-dm: Change to new style declaration
Pull RAS fixes from Thomas Gleixner:
"Two small fixes for RAS:
- Use a proper search algorithm to find the correct element in the
CEC array. The replacement was a better choice than fixing the
crash causes by the original search function with horrible duct
tape.
- Move the timer based decay function into thread context so it can
actually acquire the mutex which protects the CEC array to prevent
corruption"
* 'ras-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
RAS/CEC: Convert the timer callback to a workqueue
RAS/CEC: Fix binary search function
If mtu probing is enabled tcp_mtu_probing() could very well end up
with a too small MSS.
Use the new sysctl tcp_min_snd_mss to make sure MSS search
is performed in an acceptable range.
CVE-2019-11479 -- tcp mss hardcoded to 48
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Lemon <jonathan.lemon@gmail.com>
Cc: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Tyler Hicks <tyhicks@canonical.com>
Cc: Bruce Curtis <brucec@netflix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some TCP peers announce a very small MSS option in their SYN and/or
SYN/ACK messages.
This forces the stack to send packets with a very high network/cpu
overhead.
Linux has enforced a minimal value of 48. Since this value includes
the size of TCP options, and that the options can consume up to 40
bytes, this means that each segment can include only 8 bytes of payload.
In some cases, it can be useful to increase the minimal value
to a saner value.
We still let the default to 48 (TCP_MIN_SND_MSS), for compatibility
reasons.
Note that TCP_MAXSEG socket option enforces a minimal value
of (TCP_MIN_MSS). David Miller increased this minimal value
in commit c39508d6f1 ("tcp: Make TCP_MAXSEG minimum more correct.")
from 64 to 88.
We might in the future merge TCP_MIN_SND_MSS and TCP_MIN_MSS.
CVE-2019-11479 -- tcp mss hardcoded to 48
Signed-off-by: Eric Dumazet <edumazet@google.com>
Suggested-by: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Tyler Hicks <tyhicks@canonical.com>
Cc: Bruce Curtis <brucec@netflix.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan Looney reported that a malicious peer can force a sender
to fragment its retransmit queue into tiny skbs, inflating memory
usage and/or overflow 32bit counters.
TCP allows an application to queue up to sk_sndbuf bytes,
so we need to give some allowance for non malicious splitting
of retransmit queue.
A new SNMP counter is added to monitor how many times TCP
did not allow to split an skb if the allowance was exceeded.
Note that this counter might increase in the case applications
use SO_SNDBUF socket option to lower sk_sndbuf.
CVE-2019-11478 : tcp_fragment, prevent fragmenting a packet when the
socket is already using more than half the allowed space
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Acked-by: Yuchung Cheng <ycheng@google.com>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Cc: Bruce Curtis <brucec@netflix.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan Looney reported that TCP can trigger the following crash
in tcp_shifted_skb() :
BUG_ON(tcp_skb_pcount(skb) < pcount);
This can happen if the remote peer has advertized the smallest
MSS that linux TCP accepts : 48
An skb can hold 17 fragments, and each fragment can hold 32KB
on x86, or 64KB on PowerPC.
This means that the 16bit witdh of TCP_SKB_CB(skb)->tcp_gso_segs
can overflow.
Note that tcp_sendmsg() builds skbs with less than 64KB
of payload, so this problem needs SACK to be enabled.
SACK blocks allow TCP to coalesce multiple skbs in the retransmit
queue, thus filling the 17 fragments to maximal capacity.
CVE-2019-11477 -- u16 overflow of TCP_SKB_CB(skb)->tcp_gso_segs
Fixes: 832d11c5cd ("tcp: Try to restore large SKBs while SACK processing")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Jonathan Looney <jtl@netflix.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Bruce Curtis <brucec@netflix.com>
Cc: Jonathan Lemon <jonathan.lemon@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf 2019-06-15
The following pull-request contains BPF updates for your *net* tree.
The main changes are:
1) fix stack layout of JITed x64 bpf code, from Alexei.
2) fix out of bounds memory access in bpf_sk_storage, from Arthur.
3) fix lpm trie walk, from Jonathan.
4) fix nested bpf_perf_event_output, from Matt.
5) and several other fixes.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit ef7bfa8472.
Russell King espressed some strong opposition to this
change, explaining that this is trying to make phylink
behave outside of how it has been designed.
Signed-off-by: David S. Miller <davem@davemloft.net>
BPF_PROG_TYPE_RAW_TRACEPOINTs can be executed nested on the same CPU, as
they do not increment bpf_prog_active while executing.
This enables three levels of nesting, to support
- a kprobe or raw tp or perf event,
- another one of the above that irq context happens to call, and
- another one in nmi context
(at most one of which may be a kprobe or perf event).
Fixes: 20b9d7ac48 ("bpf: avoid excessive stack usage for perf_sample_data")
Signed-off-by: Matt Mullins <mmullins@fb.com>
Acked-by: Andrii Nakryiko <andriin@fb.com>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
bpf_sk_storage maps use multiple spin locks to reduce contention.
The number of locks to use is determined by the number of possible CPUs.
With only 1 possible CPU, bucket_log == 0, and 2^0 = 1 locks are used.
When updating elements, the correct lock is determined with hash_ptr().
Calling hash_ptr() with 0 bits is undefined behavior, as it does:
x >> (64 - bits)
Using the value results in an out of bounds memory access.
In my case, this manifested itself as a page fault when raw_spin_lock_bh()
is called later, when running the self tests:
./tools/testing/selftests/bpf/test_verifier 773 775
[ 16.366342] BUG: unable to handle page fault for address: ffff8fe7a66f93f8
Force the minimum number of locks to two.
Signed-off-by: Arthur Fabre <afabre@cloudflare.com>
Fixes: 6ac99e8f23 ("bpf: Introduce bpf sk local storage")
Acked-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Set the SOCK_DONE flag to match the TCP_CLOSING state when a peer has
shut down and there is nothing left to read.
This fixes the following bug:
1) Peer sends SHUTDOWN(RDWR).
2) Socket enters TCP_CLOSING but SOCK_DONE is not set.
3) read() returns -ENOTCONN until close() is called, then returns 0.
Signed-off-by: Stephen Barber <smbarber@chromium.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get this regression when using RTL8366RB as part of a bridge
with OpenWrt:
WARNING: CPU: 0 PID: 1347 at net/switchdev/switchdev.c:291
switchdev_port_attr_set_now+0x80/0xa4
lan0: Commit of attribute (id=7) failed.
(...)
realtek-smi switch lan0: failed to initialize vlan filtering on this port
This is because it is trying to disable VLAN filtering
on VLAN0, as we have forgot to add 1 to the port number
to get the right VLAN in rtl8366_vlan_filtering(): when
we initialize the VLAN we associate VLAN1 with port 0,
VLAN2 with port 1 etc, so we need to add 1 to the port
offset.
Fixes: d8652956cf ("net: dsa: realtek-smi: Add Realtek SMI driver")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_state field of phylink should carry only valid information
especially when this can be passed to the .mac_config callback.
Update the an_enabled field with the autoneg state in the
phylink_phy_change function.
Fixes: 9525ae8395 ("phylink: add phylink infrastructure")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Couple of driver enumeration issues have been fixed for Mellanox.
ASUS laptops got a regression with backlight, which is fixed now.
Dell computers got a wrong mode (tablet versus laptop) after resume,
that is fixed now.
The following is an automated git shortlog grouped by driver:
asus-wmi:
- Only Tell EC the OS will handle display hotkeys from asus_nb_wmi
intel-vbtn:
- Report switch events when event wakes device
mlx-platform:
- Fix parent device in i2c-mux-reg device registration
platform/mellanox:
- mlxreg-hotplug: Add devm_free_irq call to remove flow
-----BEGIN PGP SIGNATURE-----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=/H6h
-----END PGP SIGNATURE-----
Merge tag 'platform-drivers-x86-v5.2-3' of git://git.infradead.org/linux-platform-drivers-x86
Pull x86 platform driver fixes from Andy Shevchenko:
- fix a couple of Mellanox driver enumeration issues
- fix ASUS laptop regression with backlight
- fix Dell computers that got a wrong mode (tablet versus laptop) after
resume
* tag 'platform-drivers-x86-v5.2-3' of git://git.infradead.org/linux-platform-drivers-x86:
platform/mellanox: mlxreg-hotplug: Add devm_free_irq call to remove flow
platform/x86: mlx-platform: Fix parent device in i2c-mux-reg device registration
platform/x86: intel-vbtn: Report switch events when event wakes device
platform/x86: asus-wmi: Only Tell EC the OS will handle display hotkeys from asus_nb_wmi
Here are some small USB driver fixes for 5.2-rc5
Nothing major, just some small gadget fixes, usb-serial new device ids,
a few new quirks, and some small fixes for some regressions that have
been found after the big 5.2-rc1 merge.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCXQUTIg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ykPJQCfZdiElw3N35bKVf7bhruxSb5DevEAni96uDM7
jSOSEB/EWqxZEy0ZjU7J
=cKx4
-----END PGP SIGNATURE-----
Merge tag 'usb-5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB fixes from Greg KH:
"Here are some small USB driver fixes for 5.2-rc5
Nothing major, just some small gadget fixes, usb-serial new device
ids, a few new quirks, and some small fixes for some regressions that
have been found after the big 5.2-rc1 merge.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-5.2-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
usb: typec: Make sure an alt mode exist before getting its partner
usb: gadget: udc: lpc32xx: fix return value check in lpc32xx_udc_probe()
usb: gadget: dwc2: fix zlp handling
usb: dwc2: Set actual frame number for completed ISOC transfer for none DDMA
usb: gadget: udc: lpc32xx: allocate descriptor with GFP_ATOMIC
usb: gadget: fusb300_udc: Fix memory leak of fusb300->ep[i]
usb: phy: mxs: Disable external charger detect in mxs_phy_hw_init()
usb: dwc2: Fix DMA cache alignment issues
usb: dwc2: host: Fix wMaxPacketSize handling (fix webcam regression)
USB: Fix chipmunk-like voice when using Logitech C270 for recording audio.
USB: usb-storage: Add new ID to ums-realtek
usb: typec: ucsi: ccg: fix memory leak in do_flash
USB: serial: option: add Telit 0x1260 and 0x1261 compositions
USB: serial: pl2303: add Allied Telesis VT-Kit3
USB: serial: option: add support for Simcom SIM7500/SIM7600 RNDIS mode
One fix for a regression introduced by our 32-bit KASAN support, which broke
booting on machines with "bootx" early debugging enabled.
A fix for a bug which broke kexec on 32-bit, introduced by changes to the 32-bit
STRICT_KERNEL_RWX support in v5.1.
Finally two fixes going to stable for our THP split/collapse handling,
discovered by Nick. The first fixes random crashes and/or corruption in guests
under sufficient load.
Thanks to:
Nicholas Piggin, Christophe Leroy, Aaro Koskinen, Mathieu Malaterre.
-----BEGIN PGP SIGNATURE-----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=MXJI
-----END PGP SIGNATURE-----
Merge tag 'powerpc-5.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One fix for a regression introduced by our 32-bit KASAN support, which
broke booting on machines with "bootx" early debugging enabled.
A fix for a bug which broke kexec on 32-bit, introduced by changes to
the 32-bit STRICT_KERNEL_RWX support in v5.1.
Finally two fixes going to stable for our THP split/collapse handling,
discovered by Nick. The first fixes random crashes and/or corruption
in guests under sufficient load.
Thanks to: Nicholas Piggin, Christophe Leroy, Aaro Koskinen, Mathieu
Malaterre"
* tag 'powerpc-5.2-4' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/32s: fix booting with CONFIG_PPC_EARLY_DEBUG_BOOTX
powerpc/64s: __find_linux_pte() synchronization vs pmdp_invalidate()
powerpc/64s: Fix THP PMD collapse serialisation
powerpc: Fix kexec failure on book3s/32
- Out of range read of stack trace output
- Fix for NULL pointer dereference in trace_uprobe_create()
- Fix to a livepatching / ftrace permission race in the module code
- Fix for NULL pointer dereference in free_ftrace_func_mapper()
- A couple of build warning clean ups
-----BEGIN PGP SIGNATURE-----
iIoEABYIADIWIQRRSw7ePDh/lE+zeZMp5XQQmuv6qgUCXQToxhQccm9zdGVkdEBn
b29kbWlzLm9yZwAKCRAp5XQQmuv6qusmAP4/mmJPgsDchnu5ui0wB8BByzJlsPn8
luXFDuqI4f34zgD+JCmeYbj5LLh98D9XkaaEgP4yz3yKsWeSdwWPCU0vTgo=
=M/+E
-----END PGP SIGNATURE-----
Merge tag 'trace-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing fixes from Steven Rostedt:
- Out of range read of stack trace output
- Fix for NULL pointer dereference in trace_uprobe_create()
- Fix to a livepatching / ftrace permission race in the module code
- Fix for NULL pointer dereference in free_ftrace_func_mapper()
- A couple of build warning clean ups
* tag 'trace-v5.2-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace: Fix NULL pointer dereference in free_ftrace_func_mapper()
module: Fix livepatch/ftrace module text permissions race
tracing/uprobe: Fix obsolete comment on trace_uprobe_create()
tracing/uprobe: Fix NULL pointer dereference in trace_uprobe_create()
tracing: Make two symbols static
tracing: avoid build warning with HAVE_NOP_MCOUNT
tracing: Fix out-of-range read in trace_stack_print()
Adric Blake reported the following warning during suspend-resume:
Enabling non-boot CPUs ...
x86: Booting SMP configuration:
smpboot: Booting Node 0 Processor 1 APIC 0x2
unchecked MSR access error: WRMSR to 0x10f (tried to write 0x0000000000000000) \
at rIP: 0xffffffff8d267924 (native_write_msr+0x4/0x20)
Call Trace:
intel_set_tfa
intel_pmu_cpu_starting
? x86_pmu_dead_cpu
x86_pmu_starting_cpu
cpuhp_invoke_callback
? _raw_spin_lock_irqsave
notify_cpu_starting
start_secondary
secondary_startup_64
microcode: sig=0x806ea, pf=0x80, revision=0x96
microcode: updated to revision 0xb4, date = 2019-04-01
CPU1 is up
The MSR in question is MSR_TFA_RTM_FORCE_ABORT and that MSR is emulated
by microcode. The log above shows that the microcode loader callback
happens after the PMU restoration, leading to the conjecture that
because the microcode hasn't been updated yet, that MSR is not present
yet, leading to the #GP.
Add a microcode loader-specific hotplug vector which comes before
the PERF vectors and thus executes earlier and makes sure the MSR is
present.
Fixes: 400816f60c ("perf/x86/intel: Implement support for TSX Force Abort")
Reported-by: Adric Blake <promarbler14@gmail.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: <stable@vger.kernel.org>
Cc: x86@kernel.org
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203637
Pull cgroup fixes from Tejun Heo:
"This has an unusually high density of tricky fixes:
- task_get_css() could deadlock when it races against a dying cgroup.
- cgroup.procs didn't list thread group leaders with live threads.
This could mislead readers to think that a cgroup is empty when
it's not. Fixed by making PROCS iterator include dead tasks. I made
a couple mistakes making this change and this pull request contains
a couple follow-up patches.
- When cpusets run out of online cpus, it updates cpusmasks of member
tasks in bizarre ways. Joel improved the behavior significantly"
* 'for-5.2-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cpuset: restore sanity to cpuset_cpus_allowed_fallback()
cgroup: Fix css_task_iter_advance_css_set() cset skip condition
cgroup: css_task_iter_skip()'d iterators must be advanced before accessed
cgroup: Include dying leaders with live threads in PROCS iterations
cgroup: Implement css_task_iter_skip()
cgroup: Call cgroup_release() before __exit_signal()
docs cgroups: add another example size for hugetlb
cgroup: Use css_tryget() instead of css_tryget_online() in task_get_css()
- fix regression on amdgpu on SI
- fix edid override regression
- driver fixes: amdgpu, i915, mediatek, meson, panfrost
- fix writecombine for vmap in gem-shmem helper (used by panfrost)
- add more panel quirks
-----BEGIN PGP SIGNATURE-----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=4gYP
-----END PGP SIGNATURE-----
Merge tag 'drm-fixes-2019-06-14' of git://anongit.freedesktop.org/drm/drm
Pull drm fixes from Daniel Vetter:
"Nothing unsettling here, also not aware of anything serious still
pending.
The edid override regression fix took a bit longer since this seems to
be an area with an overabundance of bad options. But the fix we have
now seems like a good path forward.
Next week it should be back to Dave.
Summary:
- fix regression on amdgpu on SI
- fix edid override regression
- driver fixes: amdgpu, i915, mediatek, meson, panfrost
- fix writecombine for vmap in gem-shmem helper (used by panfrost)
- add more panel quirks"
* tag 'drm-fixes-2019-06-14' of git://anongit.freedesktop.org/drm/drm: (25 commits)
drm/amdgpu: return 0 by default in amdgpu_pm_load_smu_firmware
drm/amdgpu: Fix bounds checking in amdgpu_ras_is_supported()
drm: add fallback override/firmware EDID modes workaround
drm/edid: abstract override/firmware EDID retrieval
drm/i915/perf: fix whitelist on Gen10+
drm/i915/sdvo: Implement proper HDMI audio support for SDVO
drm/i915: Fix per-pixel alpha with CCS
drm/i915/dmc: protect against reading random memory
drm/i915/dsi: Use a fuzzy check for burst mode clock check
drm/amdgpu/{uvd,vcn}: fetch ring's read_ptr after alloc
drm/panfrost: Require the simple_ondemand governor
drm/panfrost: make devfreq optional again
drm/gem_shmem: Use a writecombine mapping for ->vaddr
drm: panel-orientation-quirks: Add quirk for GPD MicroPC
drm: panel-orientation-quirks: Add quirk for GPD pocket2
drm/meson: fix G12A primary plane disabling
drm/meson: fix primary plane disabling
drm/meson: fix G12A HDMI PLL settings for 4K60 1000/1001 variations
drm/mediatek: call mtk_dsi_stop() after mtk_drm_crtc_atomic_disable()
drm/mediatek: clear num_pipes when unbind driver
...
Eric Dumazet says:
====================
tcp: add three static keys
Recent addition of per TCP socket rx/tx cache brought
regressions for some workloads, as reported by Feng Tang.
It seems better to make them opt-in, before we adopt better
heuristics.
The last patch adds high_order_alloc_disable sysctl
to ask TCP sendmsg() to exclusively use order-0 allocations,
as mm layer has specific optimizations.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
>From linux-3.7, (commit 5640f76858 "net: use a per task frag
allocator") TCP sendmsg() has preferred using order-3 allocations.
While it gives good results for most cases, we had reports
that heavy uses of TCP over loopback were hitting a spinlock
contention in page allocations/freeing.
This commits adds a sysctl so that admins can opt-in
for order-0 allocations. Hopefully mm layer might optimize
order-3 allocations in the future since it could give us
a nice boost (see 8 lines of following benchmark)
The following benchmark shows a win when more than 8 TCP_STREAM
threads are running (56 x86 cores server in my tests)
for thr in {1..30}
do
sysctl -wq net.core.high_order_alloc_disable=0
T0=`./super_netperf $thr -H 127.0.0.1 -l 15`
sysctl -wq net.core.high_order_alloc_disable=1
T1=`./super_netperf $thr -H 127.0.0.1 -l 15`
echo $thr:$T0:$T1
done
1: 49979: 37267
2: 98745: 76286
3: 141088: 110051
4: 177414: 144772
5: 197587: 173563
6: 215377: 208448
7: 241061: 234087
8: 267155: 263373
9: 295069: 297402
10: 312393: 335213
11: 340462: 368778
12: 371366: 403954
13: 412344: 443713
14: 426617: 473580
15: 474418: 507861
16: 503261: 538539
17: 522331: 563096
18: 532409: 567084
19: 550824: 605240
20: 525493: 641988
21: 564574: 665843
22: 567349: 690868
23: 583846: 710917
24: 588715: 736306
25: 603212: 763494
26: 604083: 792654
27: 602241: 796450
28: 604291: 797993
29: 611610: 833249
30: 577356: 841062
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fei Li