A typical 100Base-T1 link should be always connected. If the link is in
a shot or open state, it is a failure. In most cases, we won't be able
to automatically handle this issue, but we need to log it or notify user
(if possible).
With this patch, the cable will be tested on "ip l s dev .. up" attempt
and send ethnl notification to the user space.
This patch was tested with TJA1102 PHY and "ethtool --monitor" command.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
The BCM54811 PHY shares many similarities with the already supported BCM54810
PHY but additionally requires some semi-unique configuration.
Signed-off-by: Kevin Lo <kevlo@kevlo.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rework and add support for dumping EOTID software context used by
TC-MQPRIO. Also track number of EOTIDs in use.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For each traffic class, firmware handles up to 4 * MTU amount of data
per burst cycle. Under heavy load, this small buffer size is a
bottleneck when buffering large TSO packets in <= 1500 MTU case.
Increase the burst buffer size to 8 * MTU when supported.
Also, keep the driver's traffic class configuration API similar to
the firmware API counterpart.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Request credit update for every half credits consumed, including
the current request. Also, avoid re-trying to post packets when there
are no credits left. The credit update reply via interrupt will
eventually restore the credits and will invoke the Tx path again.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexei Starovoitov says:
====================
pull-request: bpf-next 2020-05-15
The following pull-request contains BPF updates for your *net-next* tree.
We've added 37 non-merge commits during the last 1 day(s) which contain
a total of 67 files changed, 741 insertions(+), 252 deletions(-).
The main changes are:
1) bpf_xdp_adjust_tail() now allows to grow the tail as well, from Jesper.
2) bpftool can probe CONFIG_HZ, from Daniel.
3) CAP_BPF is introduced to isolate user processes that use BPF infra and
to secure BPF networking services by dropping CAP_SYS_ADMIN requirement
in certain cases, from Alexei.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Allow DSA to add VLAN entries even if VLAN filtering is disabled, so
enabling it will not block the traffic of existent ports in the bridge
Signed-off-by: DENG Qingfang <dqfext@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx5 driver have multiple memory models, which are also changed
according to whether a XDP bpf_prog is attached.
The 'rx_striding_rq' setting is adjusted via ethtool priv-flags e.g.:
# ethtool --set-priv-flags mlx5p2 rx_striding_rq off
On the general case with 4K page_size and regular MTU packet, then
the frame_sz is 2048 and 4096 when XDP is enabled, in both modes.
The info on the given frame size is stored differently depending on the
RQ-mode and encoded in a union in struct mlx5e_rq union wqe/mpwqe.
In rx striding mode rq->mpwqe.log_stride_sz is either 11 or 12, which
corresponds to 2048 or 4096 (MLX5_WQ_TYPE_LINKED_LIST_STRIDING_RQ).
In non-striding mode (MLX5_WQ_TYPE_CYCLIC) the frag_stride is stored
in rq->wqe.info.arr[0].frag_stride, for the first fragment, which is
what the XDP case cares about.
To reduce effect on fast-path, this patch determine the frame_sz at
setup time, to avoid determining the memory model runtime. Variable
is named frame0_sz to make it clear that this is only the frame
size of the first fragment.
This mlx5 driver does a DMA-sync on XDP_TX action, but grow is safe
as it have done a DMA-map on the entire PAGE_SIZE. The driver also
already does a XDP length check against sq->hw_mtu on the possible
XDP xmit paths mlx5e_xmit_xdp_frame() + mlx5e_xmit_xdp_frame_mpwqe().
V3+4: Change variable name first_frame_sz to frame0_sz
V2: Fix that frag_size need to be recalc before creating SKB.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Link: https://lore.kernel.org/bpf/158945348021.97035.12295039384250022883.stgit@firesoul
Intel drivers implement native AF_XDP zerocopy in separate C-files,
that have its own invocation of bpf_prog_run_xdp(). The setup of
xdp_buff is also handled in separately from normal code path.
This patch update XDP frame_sz for AF_XDP zerocopy drivers i40e, ice
and ixgbe, as the code changes needed are very similar. Introduce a
helper function xsk_umem_xdp_frame_sz() for calculating frame size.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Magnus Karlsson <magnus.karlsson@intel.com>
Link: https://lore.kernel.org/bpf/158945347511.97035.8536753731329475655.stgit@firesoul
This driver uses different memory models depending on PAGE_SIZE at
compile time. For PAGE_SIZE 4K it uses page splitting, meaning for
normal MTU frame size is 2048 bytes (and headroom 192 bytes). For
larger MTUs the driver still use page splitting, by allocating
order-1 pages (8192 bytes) for RX frames. For PAGE_SIZE larger than
4K, driver instead advance its rx_buffer->page_offset with the frame
size "truesize".
For XDP frame size calculations, this mean that in PAGE_SIZE larger
than 4K mode the frame_sz change on a per packet basis. For the page
split 4K PAGE_SIZE mode, xdp.frame_sz is more constant and can be
updated once outside the main NAPI loop.
The default setting in the driver uses build_skb(), which provides
the necessary headroom and tailroom for XDP-redirect in RX-frame
(in both modes).
There is one complication, which is legacy-rx mode (configurable via
ethtool priv-flags). There are zero headroom in this mode, which is a
requirement for XDP-redirect to work. The conversion to xdp_frame
(convert_to_xdp_frame) will detect this insufficient space, and
xdp_do_redirect() call will fail. This is deemed acceptable, as it
allows other XDP actions to still work in legacy-mode. In
legacy-mode + larger PAGE_SIZE due to lacking tailroom, we also
accept that xdp_adjust_tail shrink doesn't work.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Link: https://lore.kernel.org/bpf/158945347002.97035.328088795813704587.stgit@firesoul
This driver uses different memory models depending on PAGE_SIZE at
compile time. For PAGE_SIZE 4K it uses page splitting, meaning for
normal MTU frame size is 2048 bytes (and headroom 192 bytes). For
larger MTUs the driver still use page splitting, by allocating
order-1 pages (8192 bytes) for RX frames. For PAGE_SIZE larger than
4K, driver instead advance its rx_buffer->page_offset with the frame
size "truesize".
For XDP frame size calculations, this mean that in PAGE_SIZE larger
than 4K mode the frame_sz change on a per packet basis. For the page
split 4K PAGE_SIZE mode, xdp.frame_sz is more constant and can be
updated once outside the main NAPI loop.
The default setting in the driver uses build_skb(), which provides
the necessary headroom and tailroom for XDP-redirect in RX-frame
(in both modes).
There is one complication, which is legacy-rx mode (configurable via
ethtool priv-flags). There are zero headroom in this mode, which is a
requirement for XDP-redirect to work. The conversion to xdp_frame
(convert_to_xdp_frame) will detect this insufficient space, and
xdp_do_redirect() call will fail. This is deemed acceptable, as it
allows other XDP actions to still work in legacy-mode. In
legacy-mode + larger PAGE_SIZE due to lacking tailroom, we also
accept that xdp_adjust_tail shrink doesn't work.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Link: https://lore.kernel.org/bpf/158945346494.97035.12809400414566061815.stgit@firesoul
This patch mirrors the changes to ixgbe in previous patch.
This VF driver doesn't support XDP_REDIRECT, but correct tailroom is
still necessary for BPF-helper xdp_adjust_tail. In legacy-mode +
larger PAGE_SIZE, due to lacking tailroom, we accept that
xdp_adjust_tail shrink doesn't work.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Link: https://lore.kernel.org/bpf/158945345984.97035.13518286183248025173.stgit@firesoul
This driver uses different memory models depending on PAGE_SIZE at
compile time. For PAGE_SIZE 4K it uses page splitting, meaning for
normal MTU frame size is 2048 bytes (and headroom 192 bytes). For
larger MTUs the driver still use page splitting, by allocating
order-1 pages (8192 bytes) for RX frames. For PAGE_SIZE larger than
4K, driver instead advance its rx_buffer->page_offset with the frame
size "truesize".
For XDP frame size calculations, this mean that in PAGE_SIZE larger
than 4K mode the frame_sz change on a per packet basis. For the page
split 4K PAGE_SIZE mode, xdp.frame_sz is more constant and can be
updated once outside the main NAPI loop.
The default setting in the driver uses build_skb(), which provides
the necessary headroom and tailroom for XDP-redirect in RX-frame
(in both modes).
There is one complication, which is legacy-rx mode (configurable via
ethtool priv-flags). There are zero headroom in this mode, which is a
requirement for XDP-redirect to work. The conversion to xdp_frame
(convert_to_xdp_frame) will detect this insufficient space, and
xdp_do_redirect() call will fail. This is deemed acceptable, as it
allows other XDP actions to still work in legacy-mode. In
legacy-mode + larger PAGE_SIZE due to lacking tailroom, we also
accept that xdp_adjust_tail shrink doesn't work.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: intel-wired-lan@lists.osuosl.org
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Alexander Duyck <alexander.duyck@gmail.com>
Link: https://lore.kernel.org/bpf/158945345455.97035.14334355929030628741.stgit@firesoul
The ixgbe driver have another memory model when compiled on archs with
PAGE_SIZE above 4096 bytes. In this mode it doesn't split the page in
two halves, but instead increment rx_buffer->page_offset by truesize of
packet (which include headroom and tailroom for skb_shared_info).
This is done correctly in ixgbe_build_skb(), but in ixgbe_rx_buffer_flip
which is currently only called on XDP_TX and XDP_REDIRECT, it forgets
to add the tailroom for skb_shared_info. This breaks XDP_REDIRECT, for
veth and cpumap. Fix by adding size of skb_shared_info tailroom.
Maintainers notice: This fix have been queued to Jeff.
Fixes: 6453073987 ("ixgbe: add initial support for xdp redirect")
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Link: https://lore.kernel.org/bpf/158945344946.97035.17031588499266605743.stgit@firesoul
The virtio_net driver is running inside the guest-OS. There are two
XDP receive code-paths in virtio_net, namely receive_small() and
receive_mergeable(). The receive_big() function does not support XDP.
In receive_small() the frame size is available in buflen. The buffer
backing these frames are allocated in add_recvbuf_small() with same
size, except for the headroom, but tailroom have reserved room for
skb_shared_info. The headroom is encoded in ctx pointer as a value.
In receive_mergeable() the frame size is more dynamic. There are two
basic cases: (1) buffer size is based on a exponentially weighted
moving average (see DECLARE_EWMA) of packet length. Or (2) in case
virtnet_get_headroom() have any headroom then buffer size is
PAGE_SIZE. The ctx pointer is this time used for encoding two values;
the buffer len "truesize" and headroom. In case (1) if the rx buffer
size is underestimated, the packet will have been split over more
buffers (num_buf info in virtio_net_hdr_mrg_rxbuf placed in top of
buffer area). If that happens the XDP path does a xdp_linearize_page
operation.
V3: Adjust frame_sz in receive_mergeable() case, spotted by Jason Wang.
The code is really hard to follow, so some hints to reviewers.
The receive_mergeable() case gets frames that were allocated in
add_recvbuf_mergeable() which uses headroom=virtnet_get_headroom(),
and 'buf' ptr is advanced this headroom. The headroom can only
be 0 or VIRTIO_XDP_HEADROOM, as virtnet_get_headroom is really
simple:
static unsigned int virtnet_get_headroom(struct virtnet_info *vi)
{
return vi->xdp_queue_pairs ? VIRTIO_XDP_HEADROOM : 0;
}
As frame_sz is an offset size from xdp.data_hard_start, reviewers
should notice how this is calculated in receive_mergeable():
int offset = buf - page_address(page);
[...]
data = page_address(xdp_page) + offset;
xdp.data_hard_start = data - VIRTIO_XDP_HEADROOM + vi->hdr_len;
The calculated offset will always be VIRTIO_XDP_HEADROOM when
reaching this code. Thus, xdp.data_hard_start will be page-start
address plus vi->hdr_len. Given this xdp.frame_sz need to be
reduced with vi->hdr_len size.
IMHO a followup patch should cleanup this code to make it easier
to maintain and understand, but it is outside the scope of this
patchset.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/bpf/158945344436.97035.9445115070189151680.stgit@firesoul
The tun driver have two code paths for running XDP (bpf_prog_run_xdp).
In both cases 'buflen' contains enough tailroom for skb_shared_info.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Link: https://lore.kernel.org/bpf/158945343419.97035.9594485183958037621.stgit@firesoul
The netronome nfp driver use PAGE_SIZE when xdp_prog is set, but
xdp.data_hard_start begins at offset NFP_NET_RX_BUF_HEADROOM.
Thus, adjust for this when setting xdp.frame_sz, as it counts
from data_hard_start.
When doing XDP_TX this driver is smart and instead of a full DMA-map
does a DMA-sync on with packet length. As xdp_adjust_tail can now
grow packet length, add checks to make sure that grow size is within
the DMA-mapped size.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Jakub Kicinski <kuba@kernel.org>
Link: https://lore.kernel.org/bpf/158945342911.97035.11214251236208648808.stgit@firesoul
To help reviewers these are the defines related to RCV_FRAG_LEN
#define DMA_BUFFER_LEN 1536 /* In multiples of 128bytes */
#define RCV_FRAG_LEN (SKB_DATA_ALIGN(DMA_BUFFER_LEN + NET_SKB_PAD) + \
SKB_DATA_ALIGN(sizeof(struct skb_shared_info)))
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Sunil Goutham <sgoutham@marvell.com>
Cc: Robert Richter <rrichter@marvell.com>
Link: https://lore.kernel.org/bpf/158945342402.97035.12649844447148990032.stgit@firesoul
The mlx4 drivers size of memory backing the RX packet is stored in
frag_stride. For XDP mode this will be PAGE_SIZE (normally 4096).
For normal mode frag_stride is 2048.
Also adjust MLX4_EN_MAX_XDP_MTU to take tailroom into account.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Cc: Saeed Mahameed <saeedm@mellanox.com>
Link: https://lore.kernel.org/bpf/158945341893.97035.2688142527052329942.stgit@firesoul
Frame size ENA_PAGE_SIZE is limited to 16K on systems with larger
PAGE_SIZE than 16K. Change ENA_XDP_MAX_MTU to also take into account
the reserved tailroom.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Sameeh Jubran <sameehj@amazon.com>
Cc: Arthur Kiyanovski <akiyano@amazon.com>
Link: https://lore.kernel.org/bpf/158945341384.97035.907403694833419456.stgit@firesoul
The driver code cpsw.c and cpsw_new.c both use page_pool
with default order-0 pages or their RX-pages.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Cc: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Link: https://lore.kernel.org/bpf/158945340875.97035.752144756428532878.stgit@firesoul
The hyperv NIC driver does memory allocation and copy even without XDP.
In XDP mode it will allocate a new page for each packet and copy over
the payload, before invoking the XDP BPF-prog.
The positive thing it that its easy to determine the xdp.frame_sz.
The XDP implementation for hv_netvsc transparently passes xdp_prog
to the associated VF NIC. Many of the Azure VMs are using SRIOV, so
majority of the data are actually processed directly on the VF driver's XDP
path. So the overhead of the synthetic data path (hv_netvsc) is minimal.
Then XDP is enabled on this driver, XDP_PASS and XDP_TX will create the
SKB via build_skb (based on the newly allocated page). Now using XDP
frame_sz this will provide more skb_tailroom, which netstack can use for
SKB coalescing (e.g tcp_try_coalesce -> skb_try_coalesce).
V3: Adjust patch desc to be more positive.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Wei Liu <wei.liu@kernel.org>
Cc: "K. Y. Srinivasan" <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Link: https://lore.kernel.org/bpf/158945339857.97035.10212138582505736163.stgit@firesoul
The dpaa2-eth driver reserve some headroom used for hardware and
software annotation area in RX/TX buffers. Thus, xdp.data_hard_start
doesn't start at page boundary.
When XDP is configured the area reserved via dpaa2_fd_get_offset(fd) is
448 bytes of which XDP have reserved 256 bytes. As frame_sz is
calculated as an offset from xdp_buff.data_hard_start, an adjust from
the full PAGE_SIZE == DPAA2_ETH_RX_BUF_RAW_SIZE.
When doing XDP_REDIRECT, the driver doesn't need this reserved headroom
any-longer and allows xdp_do_redirect() to use it. This is an advantage
for the drivers own ndo-xdp_xmit, as it uses part of this headroom for
itself. Patch also adjust frame_sz in this case.
The driver cannot support XDP data_meta, because it uses the headroom
just before xdp.data for struct dpaa2_eth_swa (DPAA2_ETH_SWA_SIZE=64),
when transmitting the packet. When transmitting a xdp_frame in
dpaa2_eth_xdp_xmit_frame (call via ndo_xdp_xmit) is uses this area to
store a pointer to xdp_frame and dma_size, which is used in TX
completion (free_tx_fd) to return frame via xdp_return_frame().
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Cc: Ioana Radulescu <ruxandra.radulescu@nxp.com>
Link: https://lore.kernel.org/bpf/158945339348.97035.8562488847066908856.stgit@firesoul
The veth driver can run XDP in "native" mode in it's own NAPI
handler, and since commit 9fc8d518d9 ("veth: Handle xdp_frames in
xdp napi ring") packets can come in two forms either xdp_frame or
skb, calling respectively veth_xdp_rcv_one() or veth_xdp_rcv_skb().
For packets to arrive in xdp_frame format, they will have been
redirected from an XDP native driver. In case of XDP_PASS or no
XDP-prog attached, the veth driver will allocate and create an SKB.
The current code in veth_xdp_rcv_one() xdp_frame case, had to guess
the frame truesize of the incoming xdp_frame, when using
veth_build_skb(). With xdp_frame->frame_sz this is not longer
necessary.
Calculating the frame_sz in veth_xdp_rcv_skb() skb case, is done
similar to the XDP-generic handling code in net/core/dev.c.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Link: https://lore.kernel.org/bpf/158945338840.97035.935897116345700902.stgit@firesoul
When native XDP redirect into a veth device, the frame arrives in the
xdp_frame structure. It is then processed in veth_xdp_rcv_one(),
which can run a new XDP bpf_prog on the packet. Doing so requires
converting xdp_frame to xdp_buff, but the tricky part is that
xdp_frame memory area is located in the top (data_hard_start) memory
area that xdp_buff will point into.
The current code tried to protect the xdp_frame area, by assigning
xdp_buff.data_hard_start past this memory. This results in 32 bytes
less headroom to expand into via BPF-helper bpf_xdp_adjust_head().
This protect step is actually not needed, because BPF-helper
bpf_xdp_adjust_head() already reserve this area, and don't allow
BPF-prog to expand into it. Thus, it is safe to point data_hard_start
directly at xdp_frame memory area.
Fixes: 9fc8d518d9 ("veth: Handle xdp_frames in xdp napi ring")
Reported-by: Mao Wenan <maowenan@huawei.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Toshiaki Makita <toshiaki.makita1@gmail.com>
Acked-by: Toke Høiland-Jørgensen <toke@redhat.com>
Link: https://lore.kernel.org/bpf/158945338331.97035.5923525383710752178.stgit@firesoul
This driver takes advantage of page_pool PP_FLAG_DMA_SYNC_DEV that
can help reduce the number of cache-lines that need to be flushed
when doing DMA sync for_device. Due to xdp_adjust_tail can grow the
area accessible to the by the CPU (can possibly write into), then max
sync length *after* bpf_prog_run_xdp() needs to be taken into account.
For XDP_TX action the driver is smart and does DMA-sync. When growing
tail this is still safe, because page_pool have DMA-mapped the entire
page size.
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Link: https://lore.kernel.org/bpf/158945336295.97035.15034759661036971024.stgit@firesoul
This marvell driver mvneta uses PAGE_SIZE frames, which makes it
really easy to convert. Driver updates rxq and now frame_sz
once per NAPI call.
This driver takes advantage of page_pool PP_FLAG_DMA_SYNC_DEV that
can help reduce the number of cache-lines that need to be flushed
when doing DMA sync for_device. Due to xdp_adjust_tail can grow the
area accessible to the by the CPU (can possibly write into), then max
sync length *after* bpf_prog_run_xdp() needs to be taken into account.
For XDP_TX action the driver is smart and does DMA-sync. When growing
tail this is still safe, because page_pool have DMA-mapped the entire
page size.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Lorenzo Bianconi <lorenzo@kernel.org>
Cc: thomas.petazzoni@bootlin.com
Link: https://lore.kernel.org/bpf/158945335786.97035.12714388304493736747.stgit@firesoul
This driver uses RX page-split when possible. It was recently fixed
in commit 86e85bf698 ("sfc: fix XDP-redirect in this driver") to
add needed tailroom for XDP-redirect.
After the fix efx->rx_page_buf_step is the frame size, with enough
head and tail-room for XDP-redirect.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/158945335278.97035.14611425333184621652.stgit@firesoul
This driver uses full PAGE_SIZE pages when XDP is enabled.
In case of XDP uses driver uses __bnxt_alloc_rx_page which does full
page DMA-map. Thus, xdp_adjust_tail grow is DMA compliant for XDP_TX
action that does DMA-sync.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Cc: Michael Chan <michael.chan@broadcom.com>
Cc: Andy Gospodarek <andrew.gospodarek@broadcom.com>
Link: https://lore.kernel.org/bpf/158945334769.97035.13437970179897613984.stgit@firesoul
93882c6f21 ("r8169: switch from netif_xxx message functions to
netdev_xxx") removed the last module parameter from the driver,
therefore there's no need any longer to include linux/moduleparam.h.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After 9de5d235b6 ("net: phy: fix aneg restart in phy_ethtool_set_eee")
we don't need the check for aneg being enabled any longer, and as
discussed with Russell configuring the EEE advertisement should be
supported even if we're in a half-duplex mode currently.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently burst is clamping on rate and not burst, the assignment
of burst from the clamping discards the previous assignment of burst.
This looks like a cut-n-paste error from the previous clamping
calculation on ramp. Fix this by replacing ramp with burst.
Addresses-Coverity: ("Unused value")
Fixes: 0fbabf875d ("net: dsa: felix: add support Credit Based Shaper(CBS) for hardware offload")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio-moxart doesn't use regulators in the driver code. We can remove
the regulator include.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
AM65 CPSW h/w supports Enhanced Scheduled Traffic (EST – defined
in P802.1Qbv/D2.2 that later got included in IEEE 802.1Q-2018)
configuration. EST allows express queue traffic to be scheduled
(placed) on the wire at specific repeatable time intervals. In
Linux kernel, EST configuration is done through tc command and
the taprio scheduler in the net core implements a software only
scheduler (SCH_TAPRIO). If the NIC is capable of EST configuration,
user indicate "flag 2" in the command which is then parsed by
taprio scheduler in net core and indicate that the command is to
be offloaded to h/w. taprio then offloads the command to the
driver by calling ndo_setup_tc() ndo ops. This patch implements
ndo_setup_tc() to offload EST configuration to CPSW h/w.
Currently driver supports only SetGateStates operation. EST
operates on a repeating time interval generated by the CPTS EST
function generator. Each Ethernet port has a global EST fetch
RAM that can be configured as 2 buffers, each of 64 locations
or one large buffer of 128 locations. In 2 buffer configuration,
a ping pong mechanism is used to hold the active schedule (oper)
in one buffer and new (admin) command in the other. Each 22-bit
fetch command consists of a 14-bit fetch count (14 MSB’s) and an
8-bit priority fetch allow (8 LSB’s) that will be applied for the
fetch count time in wireside clocks. Driver process each of the
sched-entry in the offload command and update the fetch RAM.
Driver configures duration in sched-entry into the fetch count
and Gate mask into the priority fetch bits of the RAM. Then
configures the CPTS EST function generator to activate the
schedule. Currently driver supports only 2 buffer configuration
which means driver supports a max cycle time of ~8 msec.
CPSW supports a configurable number of priority queues (up to 8)
and needs to be switched to this mode from the default round
robin mode before EST can be offloaded. User configures
these through ethtool commands (-L for changing number of
queues and --set-priv-flags to disable round robin mode).
Driver doesn't enable EST if pf_p0_rx_ptype_rrobin privat flag
is set. The flag is common for all ports, and so can't be just
overridden by taprio configuration w/o user involvement.
Command fails if pf_p0_rx_ptype_rrobin is already set in the
driver.
Scheds (commands) configuration depends on interface speed so
driver translates the duration to the fetch count based on
link speed. Each schedule can be constructed with several
command entries in fetch RAM depending on interval. For example
if each sched has timer interval < ~130us on 1000 Mb link then
each sched consumes one command and have 1:1 mapping. When
Ethernet link goes down, driver purge the configuration if link
is down for more than 1 second.
The patch allows to update the timer and scheds memory only if it's
really needed, and skip cases required the user to stop timer by
configuring only shceds memory.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TAPRIO/EST offload support in CPSW2G requires EST scheduler
function enabled in CPTS. So this patch add a function to
set cycle time for EST scheduler. It also add a function for
getting time in ns of PHC clock for taprio qdisc configuration.
Mostly to verify if timer update is needed or to get actual
state of oper/admin schedule.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MCP may signal driver about generic critical failure.
Driver has to collect mdump information (get_retain),
it pushes that to logs and triggers generic notification on
"hardware attention" event.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fan failure is sent by firmware, driver reacts on this error with
newly introduced notification path. It will collect dump and shut down
the device to prevent physical breakage
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Upon tx timeout detection we do disable carrier and print TX queue
info on TX timeout. We then raise hw error condition and trigger
service task to handle this.
This handler will capture extra debug info and then optionally
trigger recovery procedure to try restore function.
Signed-off-by: Denis Bolotin <dbolotin@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Driver has an ability to initiate a recovery process as a reaction to
detected errors. But the codepath (recovery_process) was disabled and
never active.
Here we add ethtool private flag to allow user have the recovery
procedure activated.
We still do not enable this by default though, since in some configurations
this is not desirable. E.g. this may impact other PFs/VFs.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On different hardware events we have to respond differently,
on some of hardware indications hw attention (error condition)
should be cleared by the driver to continue normal functioning.
Here we introduce attention clear flags, and put them on some
important events (in aeu_descs).
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Thats probably a legacy code had double declaration of some fields.
Cleanup this, removing copy and fixing references.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
On various critical errors, notification handler should also report
the err information into the management firmware.
MFW can interact with server/motherboard backend agents - these are
used by server manufacturers to monitor server HW health.
Thus, it is important for driver to report on any faulty conditions
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a number of critical places not only debug trace should be printed,
but the appropriate hw error condition should be raised and error
handling/recovery should start.
Introduce our new qed_hw_err_notify invocation in these places to
record and indicate critical error conditions in hardware.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
qede (ethernet level driver) registers a callback handler.
This handler maintains eth dev state flags/bits to track error processing.
It implements in place processing part for nonsleeping context (WARN_ON
trigger), and a deferred (delayed work) part which triggers recovery
process for recoverable errors.
In later patches this atomic handler will come with more meat.
We introduce err_flags on ethdevice structure, its being used to record
error handling properties.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Here we introduce qed device error tracking flags and error types.
qed_hw_err_notify is an entrace point to report errors.
It'll notify higher level drivers (qede/qedr/etc) to handle and recover
the error.
List of posible errors comes from hardware interfaces, but could be
extended in future.
Signed-off-by: Ariel Elior <ariel.elior@marvell.com>
Signed-off-by: Michal Kalderon <michal.kalderon@marvell.com>
Signed-off-by: Igor Russkikh <irusskikh@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The skb_has_frag_list() in hns3_nic_net_xmit() is redundant, since
skb_walk_frags() includes this checking implicitly.
Reported-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are some macros defined in hns3_enet.h, but not used in
anywhere.
Reported-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When handling HCLGE_MBX_GET_LINK_STATUS, PF will return the link
status to the VF, so the error log of hclge_get_link_info() is
incorrect.
Reported-by: Jian Shen <shenjian15@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Oleksij Rempel