At this moment in time there is only one known configuration for the
Nomadik I2C driver. By not holding that configuration in the driver
adds some unnecessary overhead in platform code. The configuration
has already been removed from platform code, this patch checks for any
over-riding configurations. If there aren't any, the default is used.
[LinusW says: "Right now this is causing boot regressions so we need it
badly..."]
Acked-by: srinidhi kasagar <srinidhi.kasagar@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
If a device specifies zero endpoints in its interface descriptor,
the kernel oopses in acm_probe(). Even though that's clearly an
invalid descriptor, we should test wether we have all endpoints.
This is especially bad as this oops can be triggered by just
plugging a USB device in.
Signed-off-by: Sven Schnelle <svens@stackframe.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Pavel Machek <pavel@ucw.cz>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: "John W. Linville" <linville@tuxdriver.com>
CC: Eliad Peller <eliad@wizery.com>
CC: Devendra Naga <devendra.aaru@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Forest Bond <forest@alittletooquiet.net>
CC: Marcos Paulo de Souza <marcos.souza.org@gmail.com>
CC: "David S. Miller" <davem@davemloft.net>
CC: Jesper Juhl <jj@chaosbits.net>
CC: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Herton Ronaldo Krzesinski <herton@canonical.com>
CC: Hin-Tak Leung <htl10@users.sourceforge.net>
CC: Larry Finger <Larry.Finger@lwfinger.net>
CC: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Christian Lamparter <chunkeey@googlemail.com>
CC: "John W. Linville" <linville@tuxdriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Hans de Goede <hdegoede@redhat.com>
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This structure needs to always stick around, even if CONFIG_HOTPLUG
is disabled, otherwise we can oops when trying to probe a device that
was added after the structure is thrown away.
Thanks to Fengguang Wu and Bjørn Mork for tracking this issue down.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Reported-by: Bjørn Mork <bjorn@mork.no>
Cc: stable <stable@vger.kernel.org>
CC: Mauro Carvalho Chehab <mchehab@infradead.org>
CC: Michael Krufky <mkrufky@linuxtv.org>
CC: Paul Gortmaker <paul.gortmaker@windriver.com>
CC: Doron Cohen <doronc@siano-ms.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=MGmm
-----END PGP SIGNATURE-----
Merge tag 'md-3.6-fixes' of git://neil.brown.name/md
Pull md fixes from NeilBrown:
"2 fixes for md, tagged for -stable"
* tag 'md-3.6-fixes' of git://neil.brown.name/md:
md/raid10: fix problem with on-stack allocation of r10bio structure.
md: Don't truncate size at 4TB for RAID0 and Linear
This patch fixes a regression bug with the handling of zero-length
data CDBs within transport_generic_new_cmd() code. The bug was introduced
with the following commit as part of the single task conversion work:
commit 4101f0a89d
Author: Christoph Hellwig <hch@infradead.org>
Date: Tue Apr 24 00:25:03 2012 -0400
target: always allocate a single task
where the zero-length check for SCF_SCSI_DATA_SG_IO_CDB was incorrectly
changed to SCF_SCSI_CONTROL_SG_IO_CDB because of the seperate comment
in transport_generic_new_cmd() wrt to control CDBs zero-length handling
introduced in:
commit 91ec1d3535
Author: Nicholas Bellinger <nab@linux-iscsi.org>
Date: Fri Jan 13 12:01:34 2012 -0800
target: Add workaround for zero-length control CDB handling
So go ahead and change transport_generic_new_cmd() to handle control+data
zero-length CDBs in the same manner for this special case.
Tested with iscsi-target + loopback fabric port LUNs on 3.6-rc0 code.
This patch will also need to be picked up for 3.5-stable.
(hch: Add proper comment in transport_generic_new_cmd)
Cc: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
A 'struct r10bio' has an array of per-copy information at the end.
This array is declared with size [0] and r10bio_pool_alloc allocates
enough extra space to store the per-copy information depending on the
number of copies needed.
So declaring a 'struct r10bio on the stack isn't going to work. It
won't allocate enough space, and memory corruption will ensue.
So in the two places where this is done, declare a sufficiently large
structure and use that instead.
The two call-sites of this bug were introduced in 3.4 and 3.5
so this is suitable for both those kernels. The patch will have to
be modified for 3.4 as it only has one bug.
Cc: stable@vger.kernel.org
Reported-by: Ivan Vasilyev <ivan.vasilyev@gmail.com>
Tested-by: Ivan Vasilyev <ivan.vasilyev@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Suspend and resume functions call spi_master_get() without matching
spi_master_put(). The extra references are unnecessary and cause
subsequent module unload attempts to fail, so drop the calls.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The call sequence spi_alloc_master/spi_register_master/spi_unregister_master is
complete; it reduces the device reference count to zero, which and results in
device memory being freed. The subsequent call to spi_master_put is unnecessary
and results in an access to free memory. Drop it.
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
amba drivers does not need to enable pm runtime at probe.
amba_probe already enables pm runtime.
This rids this warning in the ux500 boot log:
ssp-pl022 ssp0: Unbalanced pm_runtime_enable!
Signed-off-by: Michel JAOUEN <michel.jaouen@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Due to commit cdda911c34 evdev only
becomes readable when the buffer contains an EV_SYN/SYN_REPORT event.
So in order to read the tablet sensor data as it happens we need to
ensure that we always call input_sync() after input_report_switch()
Signed-off-by: Carlos Alberto Lopez Perez <clopez@igalia.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
In the latest V-series bios DMI_PRODUCT_VERSION does not contain
the string Lenovo or Thinkpad, but is set to the model number, this
causes the thinkpad_acpi module to fail to load. Recognize laptop
as Lenovo using DMI_BIOS_VENDOR instead, which is set to Lenovo.
Test on V490u
=============
== After the patch ==
[ 1350.295757] thinkpad_acpi: ThinkPad ACPI Extras v0.24
[ 1350.295760] thinkpad_acpi: http://ibm-acpi.sf.net/
[ 1350.295761] thinkpad_acpi: ThinkPad BIOS H7ET21WW (1.00 ), EC unknown
[ 1350.295763] thinkpad_acpi: Lenovo LENOVO, model LV5DXXX
[ 1350.296086] thinkpad_acpi: detected a 8-level brightness capable ThinkPad
[ 1350.296694] thinkpad_acpi: radio switch found; radios are enabled
[ 1350.296703] thinkpad_acpi: possible tablet mode switch found; ThinkPad in laptop mode
[ 1350.306466] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is unblocked
[ 1350.307082] Registered led device: tpacpi::thinklight
[ 1350.307215] Registered led device: tpacpi::power
[ 1350.307255] Registered led device: tpacpi::standby
[ 1350.307294] Registered led device: tpacpi::thinkvantage
[ 1350.308160] thinkpad_acpi: Standard ACPI backlight interface available, not loading native one
[ 1350.308333] thinkpad_acpi: Console audio control enabled, mode: monitor (read only)
[ 1350.312287] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input14
== Before the patch ==
sudo modprobe thinkpad_acpi
FATAL: Error inserting thinkpad_acpi (/lib/modules/3.2.0-27-generic/kernel/drivers/platform/x86/thinkpad_acpi.ko): No such device
Test on B485
=============
This patch was also test in a B485 where the thinkpad_acpi module does not
have any issues loading. But, I tested it to make sure this patch does not
break on already functioning models of Lenovo products.
[13486.746359] thinkpad_acpi: ThinkPad ACPI Extras v0.24
[13486.746364] thinkpad_acpi: http://ibm-acpi.sf.net/
[13486.746368] thinkpad_acpi: ThinkPad BIOS HJET15WW(1.01), EC unknown
[13486.746373] thinkpad_acpi: Lenovo Lenovo LB485, model 814TR01
[13486.747300] thinkpad_acpi: detected a 8-level brightness capable ThinkPad
[13486.752435] thinkpad_acpi: rfkill switch tpacpi_bluetooth_sw: radio is unblocked
[13486.752883] Registered led device: tpacpi::thinklight
[13486.752915] thinkpad_acpi: Standard ACPI backlight interface available, not loading native one
[13486.753216] thinkpad_acpi: Console audio control enabled, mode: monitor (read only)
[13486.757147] input: ThinkPad Extra Buttons as /devices/platform/thinkpad_acpi/input/input15
Signed-off-by: Manoj Iyer <manoj.iyer@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Fixed the typo introduced from the below commit
5f1e88f dell-laptop: Add 6 machines to touchpad led quirk
Reported-by: Carlos Alberto Lopez Perez <clopez@igalia.com>
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
This callback is a no-op in nouveau, and the upcoming apple-gmux
switcheroo support won't require it either. Rather than forcing drivers
to stub it out, just make it optional and remove the callback from
nouveau.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
vga_switcheroo assumes that the handler will be registered before the
last client, otherwise switching will not be enabled. Likewise it's
assumed that the handler will not be unregistered without at least one
client also being unregistered, otherwise switching will remain enabled
despite no longer having a handler. These assumptions cannot be enforced
if the handler is in a separate driver from both clients, as with the
gmux found in Apple laptops. Remove this assumption.
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Add support for the gmux display muxing functionality and register a mux
handler with vga_switcheroo.
Signed-off-by: Andreas Heider <andreas@meetr.de>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Fix the dependencies of apple-gmux to prevent it from being built-in
when one or more of its dependencies is built as a module. Otherwise it
can fail to build due to missing symbols.
v2: Add dependency on ACPI to fix build failure when ACPI=n
Reported-by: Arun Raghavan <arun.raghavan@collabora.co.uk>
Signed-off-by: Seth Forshee <seth.forshee@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
If the user bit is set, that mean BIOS can't set and record the wlan
status, it will report the value read from id ASUS_WMI_DEVID_WLAN_LED
(0x00010012) while we query the wlan status by id ASUS_WMI_DEVID_WLAN
(0x00010011) through WMI.
So, we have to record wlan status in id ASUS_WMI_DEVID_WLAN_LED
(0x00010012) while setting the wlan status through WMI.
This is also the behavior that windows app will do.
Quote from ASUS application engineer
===
When you call WMIMethod(DSTS, 0x00010011) to get WLAN status, it may return
(1) 0x00050001 (On)
(2) 0x00050000 (Off)
(3) 0x00030001 (On)
(4) 0x00030000 (Off)
(5) 0x00000002 (Unknown)
(1), (2) means that the model has hardware GPIO for WLAN, you can call
WMIMethod(DEVS, 0x00010011, 1 or 0) to turn WLAN on/off.
(3), (4) means that the model doesn’t have hardware GPIO, you need to use
API or driver library to turn WLAN on/off, and call
WMIMethod(DEVS, 0x00010012, 1 or 0) to set WLAN LED status.
After you set WLAN LED status, you can see the WLAN status is changed with
WMIMethod(DSTS, 0x00010011). Because the status is recorded lastly
(ex: Windows), you can use it for synchronization.
(5) means that the model doesn’t have WLAN device.
WLAN is the ONLY special case with upper rule.
For other device, like Bluetooth, you just need use
WMIMethod(DSTS, 0x00010013) to get, and WMIMethod(DEVS, 0x00010013, 1 or 0)
to set.
===
Signed-off-by: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Matthew Garrett <mjg@redhat.com>
We were only calling acpi_video_unregister() if ACPI video support was built
in, not if it was a module.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
New gmux devices have a different method for accessing the registers.
Update the driver to cope. Incorporates feedback from Bernhard Froemel.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Bernhard Froemel <froemel@vmars.tuwien.ac.at>
Cc: Seth Forshee <seth.forshee@canonical.com>
Move the special-cased backlight update function to a generic gmux_write32
function.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Cc: Seth Forshee <seth.forshee@canonical.com>
- IPoIB fixes for regressions introduced by path database conversion
- mlx4 fixes for bugs with large memory systems and regressions from SR-IOV patches
- RDMA CM fix for passing bad event up to userspace
- Other minor fixes
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=hN/H
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband/rdma fixes from Roland Dreier:
"Grab bag of InfiniBand/RDMA fixes:
- IPoIB fixes for regressions introduced by path database conversion
- mlx4 fixes for bugs with large memory systems and regressions from
SR-IOV patches
- RDMA CM fix for passing bad event up to userspace
- Other minor fixes"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
IB/mlx4: Check iboe netdev pointer before dereferencing it
mlx4_core: Clean up buddy bitmap allocation
mlx4_core: Fix integer overflow issues around MTT table
mlx4_core: Allow large mlx4_buddy bitmaps
IB/srp: Fix a race condition
IB/qib: Fix error return code in qib_init_7322_variables()
IB: Fix typos in infiniband drivers
IB/ipoib: Fix RCU pointer dereference of wrong object
IB/ipoib: Add missing locking when CM object is deleted
RDMA/ucma.c: Fix for events with wrong context on iWARP
RDMA/ocrdma: Don't call vlan_dev_real_dev() for non-VLAN netdevs
IB/mlx4: Fix possible deadlock on sm_lock spinlock
Here are 4 tiny patches, each fixing a serial driver problem that people
have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAuh7MACgkQMUfUDdst+ym9lwCgyoxajRlnvg0aWD3WmThUt6dB
qlEAn2NZCrMEqhyBF1f7XC7Z9ETE35Yo
=m34T
-----END PGP SIGNATURE-----
Merge tag 'tty-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull TTY fixes from Greg Kroah-Hartman:
"Here are 4 tiny patches, each fixing a serial driver problem that
people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'tty-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
pmac_zilog,kdb: Fix console poll hook to return instead of loop
serial: mxs-auart: fix the wrong RTS hardware flow control
serial: ifx6x60: fix paging fault on spi_register_driver
serial: Change Kconfig entry for CLPS711X-target
If the machine is booted without any cpu_idle driver set
(b/c disable_cpuidle() has been called) we should follow
other users of cpu_idle API and check the return value
for NULL before using it.
Reported-and-tested-by: Mark van Dijk <mark@internecto.net>
Suggested-by: Jan Beulich <JBeulich@suse.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
When a kernel is built to support multiple hardware types it's possible
that CONFIG_ARCH_NEEDS_CPU_IDLE_COUPLED is set but the hardware the
kernel is run on doesn't support cpuidle and therefore doesn't load a
driver for it. In this case, when the system is shut down,
cpuidle_coupled_cpu_notify() gets called with cpuidle_devices set to
NULL. There are quite possibly other circumstances where this
situation can also occur and we should check for it.
Signed-off-by: Jon Medhurst <tixy@linaro.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The cpu hotplug notifier gets called in both atomic and non-atomic
contexts, it is not always safe to lock a mutex. Filter out all events
except the six necessary ones, which are all sleepable, before taking
the mutex.
Signed-off-by: Colin Cross <ccross@android.com>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
If __dev_pm_qos_read_value(dev) returns a negative value,
rpm_suspend() should return -EPERM for dev even if its
power.no_callbacks flag is set. For this to happen, the device's
power.no_callbacks flag has to be checked after the PM QoS check,
so move the PM QoS check to rpm_check_suspend_allowed() (this will
make it cover idle notifications as well as runtime suspend too).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
The power.deferred_resume can only be set if the runtime PM status
of device is RPM_SUSPENDING and it should be cleared after its
status has been changed, regardless of whether or not the runtime
suspend has been successful. However, it only is cleared on
suspend failure, while it may remain set on successful suspend and
is happily leaked to rpm_resume() executed in that case.
That shouldn't happen, so if power.deferred_resume is set in
rpm_suspend() after the status has been changed to RPM_SUSPENDED,
clear it before calling rpm_resume(). Then, it doesn't need to be
cleared before changing the status to RPM_SUSPENDING any more,
because it's always cleared after the status has been changed to
either RPM_SUSPENDED (on success) or RPM_ACTIVE (on failure).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
For devices whose power.no_callbacks flag is set, rpm_resume()
should return 1 if the device's parent is already active, so that
the callers of pm_runtime_get() don't think that they have to wait
for the device to resume (asynchronously) in that case (the core
won't queue up an asynchronous resume in that case, so there's
nothing to wait for anyway).
Modify the code accordingly (and make sure that an idle notification
will be queued up on success, even if 1 is to be returned).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable@vger.kernel.org
Here are some staging driver fixes (and iio driver fixes, they get lumped in
with the staging stuff due to dependancies) for your 3.6-rc3 tree.
Nothing major, just a bunch of fixes that people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAuezIACgkQMUfUDdst+ymuJgCeLF5xxKMN2qzkklpWqD7VrK26
0MgAoMyQD4aPPkrgfJm6fobqfFMRl77m
=1afu
-----END PGP SIGNATURE-----
Merge tag 'staging-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging fixes from Greg Kroah-Hartman:
"Here are some staging driver fixes (and iio driver fixes, they get
lumped in with the staging stuff due to dependancies) for your 3.6-rc3
tree.
Nothing major, just a bunch of fixes that people have reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'staging-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (26 commits)
iio: lm3533-als: Fix build warnings
staging:iio:ad7780: Mark channels as unsigned
staging:iio:ad7192: Report offset and scale for temperature channel
staging:iio:ad7192: Report channel offset
staging:iio:ad7192: Mark channels as unsigned
staging:iio:ad7192: Fix setting ACX
staging:iio:ad7192: Add missing break in switch statement
staging:iio:ad7793: Fix internal reference value
staging:iio:ad7793: Follow new IIO naming spec
staging:iio:ad7793: Fix temperature scale and offset
staging:iio:ad7793: Report channel offset
staging:iio:ad7793: Mark channels as unsigned
staging:iio:ad7793: Add missing break in switch statement
iio/adjd_s311: Fix potential memory leak in adjd_s311_update_scan_mode()
iio: frequency: ADF4350: Fix potential reference div factor overflow.
iio: staging: ad7298_ring: Fix maybe-uninitialized warning
staging: comedi: usbduxfast: Declare MODULE_FIRMWARE usage
staging: comedi: usbdux: Declare MODULE_FIRMWARE usage
staging: comedi: usbduxsigma: Declare MODULE_FIRMWARE usage
staging: csr: add INET dependancy
...
Here are two tiny patches, one fixing a dynamic debug problem that the printk
rework turned up, and the other one fixing an extcon problem that people
reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAueMIACgkQMUfUDdst+ymSRACgsoRAFYZMSG2bSCkM3LBHVpo6
w1wAoMrN+5ooCJfnWrRftn/s0M7Tpocc
=o7Cx
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core fixes from Greg Kroah-Hartman:
"Here are two tiny patches, one fixing a dynamic debug problem that the
printk rework turned up, and the other one fixing an extcon problem
that people reported.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'driver-core-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core:
extcon: extcon_gpio: Replace gpio_request_one by devm_gpio_request_one
drivers-core: make structured logging play nice with dynamic-debug
Here are some small misc and w1 driver fixes for 3.6-rc3. Nothing major, just
some some bugfixes and a new device id for a w1 driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAuepoACgkQMUfUDdst+ykHxwCgubEWwHpCC/GApX+5bAxYmJzR
keIAn0dL8oZrWujt6CrtzcV1rTxrGck8
=8Lgu
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull Char / Misc driver fixes from Greg Kroah-Hartman:
"Here are some small misc and w1 driver fixes for 3.6-rc3. Nothing
major, just some some bugfixes and a new device id for a w1 driver.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'char-misc-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
1-Wire: Add support for the maxim ds1825 temperature sensor
ti-st: Fix check for pdata->chip_awake function pointer
mei: add mei_quirk_probe function
mei: fix device stall after wd is stopped
Here are a number of small USB patches for 3.6-rc3. The "large" one is just a
number of device id updates to the option driver, done by the manufacturer,
properly fixing up the device ids based on shipping devices. Other than that,
some gadget driver fixes, the obligitary XHCI patches, and some other device
ids and bugs fixed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)
iEYEABECAAYFAlAuedoACgkQMUfUDdst+yl2DwCgzuMNDjzik/MKCTTCYARznsJ0
QIwAoMOGh+7xvCNYf9Cp8MMr/mmHZmF3
=ZEBb
-----END PGP SIGNATURE-----
Merge tag 'usb-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB patches from Greg Kroah-Hartman:
"Here are a number of small USB patches for 3.6-rc3.
The "large" one is just a number of device id updates to the option
driver, done by the manufacturer, properly fixing up the device ids
based on shipping devices.
Other than that, some gadget driver fixes, the obligitary XHCI
patches, and some other device ids and bugs fixed.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>"
* tag 'usb-3.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (26 commits)
USB: qcserial: fix port handling on Gobi 1K and 2K+
USB: serial: Fix mos7840 timeout
USB: option: add ZTE K5006-Z
usb: gadget: u_ether: fix kworker 100% CPU issue with still used interfaces in eth_stop
usb: host: tegra: fix warning messages in ehci_remove
usb: host: mips: sead3: Update for EHCI register structure.
usb: renesas_usbhs: fixup resume method for autonomy mode
usb: renesas_usbhs: mod_host: add missing .bus_suspend/resume
update MAINTAINERS for Oliver Neukum
usb: usb_wwan: resume/suspend can be called after port is gone
usb: serial: prevent suspend/resume from racing against probe/remove
usb: usb_wwan: replace release and disconnect with a port_remove hook
usb: serial: mos7840: Fixup mos7840_chars_in_buffer()
USB: isp1362-hcd.c: usb message always saved in case of underrun
OMAP: USB : Fix the EHCI enumeration and core retention issue
usb: chipidea: fix and improve dependencies if usb host or gadget support is built as module
USB: support the new interfaces of Huawei Data Card devices in option driver
USB: ftdi_sio: Add VID/PID for Kondo Serial USB
xhci: Switch PPT ports to EHCI on shutdown.
xhci: Fix bug after deq ptr set to link TRB.
...
And if not, complain loudly. None in-kernel module should trigger
that, but let us find out for sure. On the other hand, all the
out-of-tree modules will hit that. Give them some time (maybe one
release) to catch up.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes the following:
WARNING: line over 80 characters
ERROR: spaces required around that ':' (ctx:VxW)
WARNING: Prefer pr_warn(... to pr_warning(...
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Fixes the following:
WARNING: Prefer pr_warn(... to pr_warning(...
pr_warning("Waiting for status bits 0x%x to clear timed out\n",
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
The implementation in devm_request_and_ioremap() already shows error message,
so no need to show dev_err again if devm_request_and_ioremap() fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Philip, Avinash <avinashphilip@ti.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
This patch adds missing device pointer to struct pwm_chip. If the
device pointer is NULL, pwmchip_add() will return error.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
Fixes the following sparse warnings:
drivers/pwm/core.c:152:6: warning:
symbol 'of_pwmchip_add' was not declared. Should it be static?
drivers/pwm/core.c:165:6: warning:
symbol 'of_pwmchip_remove' was not declared. Should it be static?
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Thierry Reding <thierry.reding@avionic-design.de>
There is yet another way to mux the keyboard, so fix up that
group.
Signed-off-by: Patrice Chotard <patrice.chotard@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The .conf_reg of MX51_PAD_SD2_CMD__CSPI_MOSI should be 0x7bc rather
than NO_PAD. This error will cause SD2 probe failure.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
In function pinctrl_get_locked, pointer p is returned on
error, and also return on no_error.
So, we just return it with no error test.
It's pretty the same in function pinctrl_lookup_state_locked:
state is returned in every case, so we drop the error test
and just return state.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
The irqdomain conversion failed to notice that we do not always
have a DT node to dereference, fix this up by using a simple
dev_err() that also tells the name of the device.
Cc: Loic Pallardy <loic.pallardy@st.com>
Cc: Patrice Chotard <patrice.chotard@stericsson.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
GMBUS was enabled over bit-banging as the default in commits:
commit c3dfefa0a6
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Tue Feb 14 22:37:25 2012 +0100
drm/i915: reenable gmbus on gen3+ again
and
commit 0fb3f969c8
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Fri Mar 2 19:38:30 2012 +0100
drm/i915: enable gmbus on gen2
Unfortunately, GMBUS seems to fail on some CRT displays. Add a bit-banging
fallback to CRT EDID reads.
LKML-Reference: <201207251020.47637.maciej.rutecki@gmail.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45881
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Tested-by: Alex Ferrando <alferpal@gmail.com>
Cc: stable@vger.kernel.org (for 3.4+3.5)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Refactor the connector update part of intel_ddc_get_modes() into a separate
intel_connector_update_modes() function for reuse. No functional changes.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45881
Tested-by: Alex Ferrando <alferpal@gmail.com>
Cc: stable@vger.kernel.org (for 3.4+3.5)
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
They've changed it ... for no apparent reason. Meh.
V2: remove unused 'is_hsw' field.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Paulo Zanoni <paulo.r.zanoni@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
After reset we unconditionally reinitialize lists. If the context switch
hasn't yet completed before the suspend, the default context object will
end up on lists that are going to go away when we resume.
The patch forces the context switch to be synchronous before suspend
assuring that the active/inactive tracking is correct at the time of
resume.
References: https://bugs.freedesktop.org/show_bug.cgi?id=52429
Tested-by: Guang A Yang <guang.a.yang@intel.com>
Signed-off-by: Ben Widawsky <ben@bwidawsk.net>
Reviewed-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
The EDID returned by drm_get_edid() was never freed.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
This patch fixes a regression bug in pscsi_transport_complete() callback
code where *pt was being NULL dereferenced during REPORT_LUNS handling,
that was introduced with the spc/sbc refactoring in:
commit 1fd032ee10
Author: Christoph Hellwig <hch@infradead.org>
Date: Sun May 20 11:59:15 2012 -0400
target: move code for CDB emulation
As this is a special case for pscsi_parse_cdb() to call spc_parse_cdb() to
allow TCM to handle REPORT_LUN emulation, pscsi_plugin_task will have not
been allocated..
So now in pscsi_transport_complete() just check for existence of *pt and
return for this special case.
Reported-by: Alex Elsayed <eternaleye+usenet@gmail.com>
Cc: Alex Elsayed <eternaleye+usenet@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch changes the vhost_scsi_target->vhost_wwpn[] type used
by VHOST_SCSI_* ioctls to 'char *' as requested by Blue Swirl in
order to match the latest QEMU vhost-scsi RFC-v3 userspace code.
Queuing this up into target-pending/master for a -rc3 PULL.
Reported-by: Blue Swirl <blauwirbel@gmail.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
I am hitting this bug when the target is low in memory that fails the
alloc_page() for the newly submitted command. This is a sort of off-by-one
bug causing NULL pointer dereference in __free_page() since 'i' here is
really the counter of total pages that have been successfully allocated here.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Cc: Andy Grover <agrover@redhat.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Cc: Open-FCoE.org <devel@open-fcoe.org>
Cc: stable@vger.kernel.org
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Stop doing a pile of work related to debugging messages when
the ft_debug_logging flag is not set. Use unlikely to add the
check in a way that the check can be inlined without inlining the
whole thing.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
This patch contains the post RFC-v5 (post-merge) changes, this includes:
- Add locking comment
- Move vhost_scsi_complete_cmd ahead of TFO callbacks in order to
drop forward declarations
- Drop extra '!= NULL' usage in vhost_scsi_complete_cmd_work()
- Change vhost_scsi_*_handle_kick() to use pr_debug
- Fix possible race in vhost_scsi_set_endpoint() for vs->vs_tpg checking
+ assignment.
- Convert tv_tpg->tpg_vhost_count + ->tv_tpg_port_count from atomic_t ->
int, and make sure reference is protected by ->tv_tpg_mutex.
- Drop unnecessary vhost_scsi->vhost_ref_cnt
- Add 'err:' label for exception path in vhost_scsi_clear_endpoint()
- Add enum for VQ numbers, add usage in vhost_scsi_open()
- Add vhost_scsi_flush() + vhost_scsi_flush_vq() following
drivers/vhost/net.c
- Add smp_wmb() + vhost_scsi_flush() call during vhost_scsi_set_features()
- Drop unnecessary copy_from_user() usage with GET_ABI_VERSION ioctl
- Add missing vhost_scsi_compat_ioctl() caller for vhost_scsi_fops
- Fix function parameter definition first line to follow existing
vhost code style
- Change 'vHost' usage -> 'vhost' in handful of locations
- Change -EPERM -> -EBUSY usage for two failures in tcm_vhost_drop_nexus()
- Add comment for tcm_vhost_workqueue in tcm_vhost_init()
- Make GET_ABI_VERSION return 'int' + add comment in tcm_vhost.h
Reported-by: Michael S. Tsirkin <mst@redhat.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Stefan Hajnoczi <stefanha@linux.vnet.ibm.com>
Cc: Anthony Liguori <aliguori@us.ibm.com>
Cc: Zhi Yong Wu <wuzhy@cn.ibm.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
These mostly consist of fixes from Lars-Peter Clausen that were
the first part of a large series reworking the drivers concerned.
Turns out these drivers had quite a wealth of minor bugs.
Also here are some build warning fixes for lm3533-als and
adjd_s111 (both new drives in this cycle).
Final elements are a a div factor overflow and a warning
related fix in a couple of Analog Devices drivers.
All in all nothing major, but a worthwhile bunch of short
fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQIcBAABAgAGBQJQLUxMAAoJEFSFNJnE9BaI1PgQALfDZXRXLaR3zxp+ZJMZsY6e
LkGbi0PioGXyJG0/a5KYTTntFGrWTR6RDhofG1AAMiUCvfmR68a5E4dS3C+huHx4
5yvoiFo2W70Cuavne34C15ObmCX2sBQx9T0i1xMCbqizjN7hfwCsM2gyieMJ3/so
xhxV1wvztqJOfLY93fGZUe7sz9vZa34fdZ5cgAQqF1GpO9awDY/fvMb6ecAJjPqV
qxgsmdXhYJ0v41ukjnvZbebeHZKcbf6Ffo1DGLCvjw8w8h1JMdg8/gXuwmj3RLcY
Y/oUvfUFGOx0RRkbGamgxhwo2STQ9SDwUohzblIufY38HFAEfiBFueJ7IctxXy6K
HPdm0UL4nDgs751rOh5on3lbiv4wX0RHsXwkoKIXlueK0rptQ+uA+Uq/irCnEfJy
xxn0X03kaNMgNtI3EK3/PbEsPpDEoVpeNHFW+ikVl6FBCjRpraoxnNGMg6ajV9kH
U0Wigwj0vVZdVwpUQAXZoz1so/i00mC5pHOt+3znReEdgJkV63AnlY69IbjvxoLi
3eq50EMZUsxbCQdDdIIADPtabwxKRN2rphRMb/eAG/6ZAJCYZWrhrli/OTUmqzXs
4MaYEPyAjpUiyABVtKzONtSccP640kz3YSIg6ZKwGGYoI0/jXTlrXTlsKQUeNOtn
ll/kwhqy1mXYW+Q7kpj3
=+LMV
-----END PGP SIGNATURE-----
Merge tag 'v3.6-rc1-iio-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
IIO fixes for v3.6-rc1
These mostly consist of fixes from Lars-Peter Clausen that were
the first part of a large series reworking the drivers concerned.
Turns out these drivers had quite a wealth of minor bugs.
Also here are some build warning fixes for lm3533-als and
adjd_s111 (both new drives in this cycle).
Final elements are a a div factor overflow and a warning
related fix in a couple of Analog Devices drivers.
All in all nothing major, but a worthwhile bunch of short
fixes.
This patch adds support for maxim ds1825 based 1-wire temperature sensors.
Signed-off-by: Raphael Assenat <raph@8d.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
ll_device_want_to_wakeup(): Fix the NULL pointer check on pdata->chip_awake,
which is performed on the wrong function pointer
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix below build warnings:
CC [M] drivers/iio/light/lm3533-als.o
drivers/iio/light/lm3533-als.c:667:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/iio/light/lm3533-als.c:667:8: warning: (near initialization for 'dev_attr_in_illuminance0_thresh_either_en.show') [enabled by default]
drivers/iio/light/lm3533-als.c:667:8: warning: initialization from incompatible pointer type [enabled by default]
drivers/iio/light/lm3533-als.c:667:8: warning: (near initialization for 'dev_attr_in_illuminance0_thresh_either_en.store') [enabled by default]
Signed-off-by: Axel Lin <axel.lin@gmail.com>
The values reported by the AD7780 are unsigned with a binary offset:
0x000000 is negative fullscale
0x800000 is zeroscale
0xffffff is positive fullscale
So mark the channel in the channel spec as unsigned rather than signed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The temperature channel reports values in degree Kelvin with sensitivity of 5630
codes per degree. If the chip is configured in bipolar mode there is an
additional binary offset of 0x800000 and the sensitivity is divided by two.
Currently the driver does the mapping from the raw value to degree Celsius when
doing a manual conversion. This has several disadvantages, the major one being
that it does not work for buffered mode, also by doing the division by the
sensitivity in the driver the precession of the reported value is needlessly
reduced.
Furthermore the current calculation only works in bipolar mode and the current
scale is of by a factor of 1000.
This patch modifies the driver to report correct offset and scale values in
both unipolar and bipolar mode and to report the raw temperature value
for manual conversions.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In bipolar mode there is a a binary offset of 2**(N-1) (with N being the number
of bits) on the reported value. Currently this value is subtracted when doing a
manual read. While this works for manual channel readings it does not work for
buffered mode. So report the offset in the channels offset property, which will
work in both modes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
The values reported by the AD7793 are unsigned.
In uniploar mode:
0x000000 is zeroscale
0xffffff is fullscale
In bipolar mode:
0x000000 is negative fullscale
0x800000 is zeroscale
0xffffff is positive fullscale
In bipolar mode there is a binary offset, but the values are still unsigned.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Write to the correct register when setting the ACX bit.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Without the break statement we fall right through to the default case and return
an error value.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The internal reference for the ad7793 and similar is 1.17V
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Make the "in-in_scale_available" attribute follow the new naming spec and
rename it to "in_voltage-voltage_scale_available".
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The temperature channel uses the internal 1.17V reference with 0.81 mv/C. The
reported temperature is in Kevlin, so we need to add the Kelvin to Celcius
offset when reporting the offset for the temperature channel.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
In bipolar mode there is a a binary offset of 2**(N-1) (with N being the number
of bits) on the reported value. Currently this value is subtracted when doing a
manual read. While this works for manual channel readings it does not work for
buffered mode. So report the offset in the channels offset property, which will
work in both modes.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The values reported by the AD7793 are unsigned.
In uniploar mode:
0x000000 is zeroscale
0xffffff is fullscale
In bipolar mode:
0x000000 is negative fullscale
0x800000 is zeroscale
0xffffff is positive fullscale
In bipolar mode there is a binary offset, but the values are still unsigned.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Without the break statement we fall right through to the default case and return
an error value.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Do not leak memory by updating pointer with potentially NULL realloc return value.
There is no need to preserve data in the buffer,
so replace krealloc() by kfree()-kmalloc() pair.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Acked-by: Peter Meerwald <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
With small channel spacing values and high reference frequencies it is
possible to exceed the range of the 10-bit counter.
Workaround by checking the range and widening some constrains.
We don't use the REG1_PHASE value in this case the datasheet recommends to set
it to 1 if not used.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
drivers/staging/iio/adc/ad7298_ring.c:97:37: warning: 'time_ns' may
be used uninitialized in this function [-Wmaybe-uninitialized]
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
kdb <-> kgdb transitioning does not work properly with this UART
driver because the get character routine loops indefinitely as opposed
to returning NO_POLL_CHAR per the expectation of the KDB I/O driver
API.
The symptom is a kernel hang when trying to switch debug modes.
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Without checking if the auart supports the hardware flow control or not,
the old mxs_auart_set_mctrl() asserted the RTS pin blindly.
This will causes the auart receives wrong data in the following case:
The far-end has already started the write operation, and wait for
the auart asserts the RTS pin. Then the auart starts the read operation,
but mxs_auart_set_mctrl() may be called before we set the RTSCTS in the
mxs_auart_settermios(). So the RTS pin is asserted in a wrong situation,
and we get the wrong data in the end.
This bug has been catched when I connect the mx23(DTE) to the mx53(DCE).
This patch also replaces the AUART_CTRL2_RTS with AUART_CTRL2_RTSEN.
We should use the real the hardware flow control, not the software-controled
hardware flow control.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This driver is a replacement for a MAX3107 driver with a lot of
improvements and new features.
The main differences from the old version:
- Using the regmap.
- Using devm_XXX-related functions.
- The use of threaded IRQ with IRQF_ONESHOT flag allows the driver to
the hardware that supports only level IRQ.
- Improved error handling of serial port, improved FIFO handling,
improved hardware & software flow control.
- Advanced flags allows turn on RS-485 mode (Auto direction control).
- Ability to load multiple instances of drivers.
- Added support for MAX3108.
- GPIO support.
- Driver is quite ready for adding I2C support and support other ICs
with compatible registers set (MAX3109, MAX14830).
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
OMAP hardware doesn't provide a phyisical DTR line, but
some configurations may need a DTR line which tracks whether
the device is open or not.
So allow a gpio to be configured as the DTR line.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Reported by coccinelle:
drivers/tty/serial/pch_uart.c:979:1-14: alloc with no test, possible model on line 994
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes the following compile breakage:
CC drivers/tty/serial/sc26xx.o
drivers/tty/serial/sc26xx.c: In function 'read_sc_port':
drivers/tty/serial/sc26xx.c💯 error: implicit declaration of function 'readb'
drivers/tty/serial/sc26xx.c: In function 'write_sc_port':
drivers/tty/serial/sc26xx.c:105: error: implicit declaration of function 'writeb'
drivers/tty/serial/sc26xx.c: In function 'sc26xx_probe':
drivers/tty/serial/sc26xx.c:652: error: implicit declaration of function 'ioremap_nocache'
drivers/tty/serial/sc26xx.c:652: warning: assignment makes pointer from integer without a cast
make[3]: *** [drivers/tty/serial/sc26xx.o] Error 1
make[2]: *** [drivers/tty/serial] Error 2
make[1]: *** [drivers/tty] Error 2
make: *** [drivers] Error 2
Signed-off-by: Alexander Shiyan <shc_work@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We changed these from alloc_tty_driver() to tty_alloc_driver() so the
error handling needs to modified to check for IS_ERR() instead of NULL.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Uplink (TX) network data will go through gsm_dlci_data_output_framed
there is a bug where if memory allocation fails, the skb which
has already been pulled off the list will be lost.
In addition TX skbs were being processed in LIFO order
Fixed the memory leak, and changed to FIFO order processing
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Kappel, LaurentX <laurentx.kappel@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Showjumping <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Drivers are supposed to use the dev_* versions of the kfree_skb
interfaces. In a couple of cases we were called with IRQs
disabled as well which kfree_skb() does not expect.
Replaced kfree_skb calls w/ dev_kfree_skb and dev_kfree_skb_any
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Grooming <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsm_data_kick was recently modified to allow messages on the
tx queue bound for DLCI0 to flow even during FCOFF conditions.
Unfortunately we introduced a bug discovered by code inspection
where subsequent list traversers can access freed memory if
the DLCI0 messages were not all at the head of the list.
Replaced singly linked tx list w/ a list_head and used
provided interfaces for traversing and deleting members.
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Riding School <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There were some locking holes in the management of the MUX's
message queue for 2 code paths:
1) gsmld_write_wakeup
2) receipt of CMD_FCON flow-control message
In both cases gsm_data_kick is called w/o locking so it can collide
with other other instances of gsm_data_kick (pulling messages tx_tail)
or potentially other instances of __gsm_data_queu (adding messages to tx_head)
Changed to take the tx_lock in these 2 cases
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Riding School <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The design of uplink flow control in the mux driver is
that for constipated channels data will backup into the
per-channel fifos, and any messages that make it to the
outbound message queue will still go out.
Code was added to also stop messages that were in the outbound
queue but this requires filtering through all the messages on the
queue for stopped dlcis and changes some of the mux logic unneccessarily.
The message fiiltering was removed to be in line w/ the original design
as the message filtering does not provide any solution.
Extra debug messages used during investigation were also removed.
Signed-off-by: samix.lebsir <samix.lebsir@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Dressage <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
- Correcting handling of FCon/FCoff in order to respect 27.010 spec
- Consider FCon/off will overide all dlci flow control except for
dlci0 as we must be able to send control frames.
- Dlci constipated handling according to FC, RTC and RTR values.
- Modifying gsm_dlci_data_kick and gsm_dlci_data_sweep according
to dlci constipated value
Signed-off-by: Frederic Berat <fredericx.berat@intel.com>
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gsm_dlci_data_kick will not call any output function if tx_bytes > THRESH_LO
furthermore it will call the output function only once if tx_bytes == 0
If the size of the IP writes are on the order of THRESH_LO
we can get into a situation where skbs accumulate on the outbound list
being starved for events to call the output function.
gsm_dlci_data_kick now calls the sweep function when tx_bytes==0
Signed-off-by: Russ Gorby <russ.gorby@intel.com>
Tested-by: Kappel, LaurentX <laurentx.kappel@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Hay and Water <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In 3GPP27.010 5.8.1, it defined:
The TE multiplexer initiates the establishment of the multiplexer control channel by sending a SABM frame on DLCI 0 using the procedures of clause 5.4.1.
Once the multiplexer channel is established other DLCs may be established using the procedures of clause 5.4.1.
This patch implement 5.8.1 in MUX level, it make sure DLC0 is the first channel to be setup.
[or for those not familiar with the specification: it was possible to try
and open a data connection while the control channel was not yet fully
open, which is a spec violation and confuses some modems]
Signed-off-by: xiaojin <jin.xiao@intel.com>
Tested-by: Yin, Fengwei <fengwei.yin@intel.com>
[tweaked the order we check things and error code]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: The Horsebox <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Change the BUG_ON to WARN_ON and return in case of tty->read_buf==NULL. We want to track a
couple of long standing reports of this but at the same time we can avoid killing the box.
Signed-off-by: Stanislav Kozina <skozina@redhat.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: Horses <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Pull two slave-dmaengine fixes from Vinod Koul:
"One fixes the correct use of clock API in imx driver and the other
enables clock for tegra driver, which is used for other tegra driver
conversion to dmanegine in -next."
* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
dma: tegra: enable/disable dma clock
dma: imx-dma: Fix kernel crash due to missing clock conversion
Pull more drm fixes from Dave Airlie:
"Just some intel and nouveau ones this time, intel has more edp panel
fixes for macbooks and nouveau has a suspend/resume regression fix in
there."
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
drm/i915: Apply post-sync write for pipe control invalidates
drm/i915: reorder edp disabling to fix ivb MacBook Air
drm/nv86/fifo: suspend fix
drm/nouveau: disable copy engine on NVAF
nouveau: fixup scanout enable in nvc0_pm
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
drm/i915: ensure i2c adapter is all set before adding it
drm/i915: ignore eDP bpc settings from vbt
drm/i915: Fix blank panel at reopening lid
drm/nve0/fifo: add support for the flip completion swmthd
The main purpose of this function is to exclude ME devices
without support for MEI/HECI interface from binding
Currently affected systems are C600/X79 based servers
that expose PCI device even though it doesn't supported ME Interface.
MEI driver accessing such nonfunctional device can corrupt
the system.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit 01eaf24 "extcon: Convert extcon_gpio to devm_gpio_request_one"
missed the replacement for devm_gpio_request_one. fix it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
commit c4e00daaa9 changed __dev_printk
in a way that broke dynamic-debug's ability to control the dynamic
prefix of dev_dbg(dev,..), but not dev_dbg(NULL,..) or pr_debug(..),
which is why it wasnt noticed sooner.
When dev==NULL, __dev_printk() just calls printk(), which just works.
But otherwise, it assumed that level was always a string like "<L>"
and just plucked out the 'L', ignoring the rest. However,
dynamic_emit_prefix() adds "[tid] module:func:line:" to the string,
those additions all got lost.
Signed-off-by: Jim Cromie <jim.cromie@gmail.com>
Acked-by: Jason Baron <jbaron@redhat.com>
Cc: stable <stable@vger.kernel.org>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Bjorn's latest patchset does break Gobi 1K and 2K because on both
devices as it claims usb interface 0. That's because usbif 0 is not
handled in the switch statement, and thus the if0 gets claimed when it
should not. So let's just make things even simpler yet, and handle both
the 1K and 2K+ cases separately. This patch should not affect the new
Sierra device support, because those devices are matched via
interface-specific matching and thus should never hit the composite
code.
Signed-off-by: Dan Williams <dcbw@redhat.com>
Tested-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After watchdog was disabled the driver would stall
due to wrong calculation of credits reduction
The cat&paste bug was introduced in the commit
7bdf72d3d8
mei: introduce mei_data2slots wrapper
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Unlike other parts of the mlx4_ib code, the function build_mlx_header()
doesn't check if the iboe netdev of the given port is valid before
dereferencing it, which can cause a crash if the ethernet interface
has already been taken down.
Fix this by checking for a valid netdev pointer before using it to get
the port MAC address.
Signed-off-by: Kleber Sacilotto de Souza <klebers@linux.vnet.ibm.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
commit 27a7b260f7
md: Fix handling for devices from 2TB to 4TB in 0.90 metadata.
changed 0.90 metadata handling to truncated size to 4TB as that is
all that 0.90 can record.
However for RAID0 and Linear, 0.90 doesn't need to record the size, so
this truncation is not needed and causes working arrays to become too small.
So avoid the truncation for RAID0 and Linear
This bug was introduced in 3.1 and is suitable for any stable kernels
from then onwards.
As the offending commit was tagged for 'stable', any stable kernel
that it was applied to should also get this patch. That includes
at least 2.6.32, 2.6.33 and 3.0. (Thanks to Ben Hutchings for
providing that list).
Cc: stable@vger.kernel.org
Signed-off-by: Neil Brown <neilb@suse.de>
- Use kcalloc() / vzalloc() instead of an extra bitmap_zero().
- Add __GFP_NOWARN to kcalloc() since we'll try vzalloc() if it fails.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Fix some issues around int variables used in data structures related
to memory registration.
Handle int overflow in mlx4_init_icm_table by using a u64 intermediate
variable and changing struct mlx4_icm_table num_obj field to be u32.
Change some more fields/variables to use u32 instead of int to prevent
a case where the variable becomes negative when bit 31 is set.
Also subtract log_mtts_per_seg from the exponent when computing
num_mtt, since its added later on in that very same code area.
This and the previous commit fixes some issues which actually prevent
commit db5a7a65c0 ("mlx4_core: Scale size of MTT table with system
RAM") from working. Now, when the number of MTTs is scaled with the
size of the RAM we can map up to 8TB.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Jack Morgenstein <jackm@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
mlx4_buddy_init uses kmalloc() to allocate bitmaps, which fails when
the required size is beyond the max supported value (or when memory is
too fragmented to handle a huge allocation). Extend this to use use
vmalloc() if kmalloc() fails, and take that into account when freeing
the bitmaps as well.
This fixes a driver load failure when log num mtt is 26 or higher, and
is a step in the direction of allowing to register huge amounts of
memory on large memory systems.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
In JPEG mode, the size of image is variable due to different JPEG compression
rate. We only can get the pix->sizeimage from the user.
If we clear pix->sizeimage in soc_camera_try_fmt() then we will get it from:
ret = soc_mbus_image_size(xlate->host_fmt, pix->bytesperline,
pix->height);
if (ret < 0)
return ret;
pix->sizeimage = max_t(u32, pix->sizeimage, ret);
In general, this sizeimage will be larger than the actul JPEG image size.
But vb2 will check the buffer and size of image in __qbuf_userptr():
/* Check if the provided plane buffer is large enough */
if (planes[plane].length < q->plane_sizes[plane])
So we shouldn't clear the pix->sizeimage and also shouldn't re-calculate
the pix->sizeimage in soc_mbus_image_size() in JPEG mode
We also shouldn't re-calculate pix->bytesperline:
ret = soc_mbus_bytes_per_line(pix->width, xlate->host_fmt);
if (ret < 0)
return ret;
pix->bytesperline = max_t(u32, pix->bytesperline, ret);
pix->bytesperline also should be set by the user or by the driver's
try_fmt() implementation.
Change-Id: I700690a2287346127a624b5260922eaa5427a596
Signed-off-by: Albert Wang <twang13@marvell.com>
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
On i.MX27 two clocks are required: emma-ipg and emma-ahb. The ahb clock
has to be requested using both a device and a connection ID.
Signed-off-by: Javier Martin <javier.martin@vista-silicon.com>
[g.liakhovetski@gmx.de: rebase to the current media tree]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
This patch checks the state of the buffer when calling .buf_init() method.
This is needed for the USERPTR buffer type, because in that case
.buf_init() is called every time a buffer is queued, and not only once
during the preparation stage, like in the MMAP case. Without this check
buffers get initialised repeatedly, which also leads to the allocation
of new DMA descriptors, of which there is only a final relatively small
number available. Both MMAP and USERPTR methods were successfully tested.
Signed-off-by: Alex Gershgorin <alexg@meprolight.com>
[g.liakhovetski@gmx.de: remove mx3_camera_buffer::state completely]
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
* mos7840 driver was using multiple of HZ for the timeout handed off to
usb_control_msg(). Changed the timeout to use msecs instead.
* Remove unused WAIT_FOR_EVER definition
Signed-off-by: Mark Ferrell <mferrell@uplogix.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The ZTE (Vodafone) K5006-Z use the following
interface layout:
00 DIAG
01 secondary
02 modem
03 networkcard
04 storage
Ignoring interface #3 which is handled by the qmi_wwan
driver.
Cc: Thomas Schäfer <tschaefer@t-online.de>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
dev_open() can complete before register_netdev() returns.
Fix vmxnet3_probe_device() to support this.
Signed-off-by: Steve Hodgson <steve@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid a crash caused by the scmnd->scsi_done(scmnd) call in
srp_process_rsp() being invoked with scsi_done == NULL. This can
happen if a reply is received during or after a command abort.
Reported-by: Joseph Glanville <joseph.glanville@orionvm.com.au>
Reference: http://marc.info/?l=linux-rdma&m=134314367801595
Cc: <stable@vger.kernel.org>
Acked-by: David Dillow <dillowda@ornl.gov>
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Convert a 0 error return code to a negative one, as returned elsewhere
in the function.
A simplified version of the semantic match that finds this problem is
as follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Mike Marciniszyn <mike.marciniszyn@intel.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Correct spelling typos in comments in drivers/infiniband.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit dbf0e4c (PCI: EHCI: fix crash during suspend on ASUS
computers) added a workaround for an ASUS suspend issue related to
USB EHCI and a bug in a number of ASUS BIOSes that attempt to shut
down the EHCI controller during system suspend if its PCI command
register doesn't contain 0 at that time.
It turns out that the same workaround is necessary in the analogous
hibernation code path, so add it.
References: https://bugzilla.kernel.org/show_bug.cgi?id=45811
Reported-and-tested-by: Oleksij Rempel <bug-track@fisher-privat.net>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: stable@vger.kernel.org
If a PCI device is put into D3_cold by acpi_bus_set_power(),
the message printed by acpi_pci_set_power_state() says that its
power state has been changed to D4, which doesn't make sense.
In turn, if the device is put into D3_hot, the message simply
says "D3" without specifying the variant of the D3 state.
Fix this by using the pci_power_name() macro for printing the state
name instead of building it from the numeric value corresponding to
the given state directly.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
It seems commit 2098e95ce9 (regulator: twl:
adapt twl-regulator driver to dt) accidentally deleted VINTANA1. Also
the same commit defines VINTANA2 twice with TWL4030_ADJUSTABLE_LDO and
TWL4030_FIXED_LDO. This patch changes the fixed one to be VINTANA1.
I noticed this when auditing my N900 boot logs. I could not notice any
change in device behaviour, though, except that the boot logs are now
like before:
...
[ 0.282928] VDAC: 1800 mV normal standby
[ 0.284027] VCSI: 1800 mV normal standby
[ 0.285400] VINTANA1: 1500 mV normal standby
[ 0.286865] VINTANA2: 2750 mV normal standby
[ 0.288208] VINTDIG: 1500 mV normal standby
[ 0.289978] VSDI_CSI: 1800 mV normal standby
...
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@vger.kernel.org
* 'drm-nouveau-fixes' of git://git.freedesktop.org/git/nouveau/linux-2.6:
drm/nv86/fifo: suspend fix
drm/nouveau: disable copy engine on NVAF
nouveau: fixup scanout enable in nvc0_pm
drm/nouveau/aux: mask off higher bits of auxch index in i2c table entry
drm/nvd0/disp: mask off high 16 bit of negative cursor x-coordinate
drm/nve0/fifo: add support for the flip completion swmthd
Daniel Vetter writes:
"A few important fixers:
- fix various lvds backlight issues, regressed in 3.6 (Takashi Iwai)
- make the retina mbp work (ignore bogus edp bpc value in vbt)
- fix a gmbus regression introduced in (iirc) 3.4 (Jani Nikula)
- fix an edp panel power sequence regression, fixes the new macbook air
- apply the tlb invalidate w/a
Otherwise we still have another gmbus regression (patches are awaiting
tested-bys) and there's something odd going with some rare systems not
entering rc6 often enough (and hence blowing through too much power). It
seems to be a timing-related issue and can be mitigated by frobbing the
magic tuning parameters. We're still working on that one. Also, we still
have some fallout from the hw context support, but you can only hit that
with mesa master."
* 'drm-intel-fixes' of git://people.freedesktop.org/~danvet/drm-intel:
drm/i915: Apply post-sync write for pipe control invalidates
drm/i915: reorder edp disabling to fix ivb MacBook Air
drm/i915: ensure i2c adapter is all set before adding it
drm/i915: ignore eDP bpc settings from vbt
drm/i915: Fix blank panel at reopening lid
John W. Linville says:
====================
Alexey Khoroshilov provides a potential memory leak in rndis_wlan.
Bob Copeland gives us an ath5k fix for a lockdep problem.
Dan Carpenter fixes a signedness mismatch in at76c50x.
Felix Fietkau corrects a regression caused by an earlier commit that can
lead to an IRQ storm.
Lorenzo Bianconi offers a fix for a bad variable initialization in ath9k
that can cause it to improperly mark decrypted frames.
Rajkumar Manoharan fixes ath9k to prevent the btcoex time from running
when the hardware is asleep.
The remainder are Bluetooth fixes, about which Gustavo says:
"Here goes some fixes for 3.6-rc1, there are a few fix to
thte inquiry code by Ram Malovany, support for 2 new devices,
and few others fixes for NULL dereference, possible deadlock
and a memory leak."
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Convert a 0 error return code to a negative one, as returned elsewhere in the
function.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@
(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
when != ret = e3
*if (x == NULL || ...)
{
... when != ret = e4
* return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the NULL test is necessary, the initialization involving a dereference of
the tested value should be moved after the NULL test.
The sematic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
type T;
expression E;
identifier i,fld;
statement S;
@@
- T i = E->fld;
+ T i;
... when != E
when != i
if (E == NULL) S
+ i = E->fld;
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Randy noticed that with CONFIG_INET turned off, the following build
errors happen:
ERROR: "register_inetaddr_notifier" [drivers/staging/csr/csr_wifi.ko] undefined!
ERROR: "unregister_inetaddr_notifier" [drivers/staging/csr/csr_wifi.ko] undefined!
Reported-by: Randy Dunlap <rdunlap@xenotime.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit 3902a37028 (staging: comedi:
refactor comedi_device_attach() a bit) by yours truly introduced an
inverted logic bug in comedi_device_attach() for the case where the
driver expects the device to be configured by driver name rather than
board name. The result of a strcmp() is being tested incorrectly. Fix
it.
Thanks to Stephen N Chivers for discovering the bug and suggesting the
fix.
Cc: <stable@vger.kernel.org> # 3.5.x
Signed-off-by: Ian Abbott <abbotti@mev.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Commit b63b70d877 ("IPoIB: Use a private hash table for path lookup
in xmit path") introduced a bug where in ipoib_neigh_free() (which is
called from a few errors flows in the driver), rcu_dereference() is
invoked with the wrong pointer object, which results in a crash.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Commit b63b70d877 ("IPoIB: Use a private hash table for path lookup
in xmit path") introduced a bug where in ipoib_cm_destroy_tx() a CM
object is moved between lists without any supported locking. Under a
stress test, this eventually leads to list corruption and a crash.
Previously when this routine was called, callers were taking the
device priv lock. Currently this function is called from the RCU
callback associated with neighbour deletion. Fix the race by taking
the same lock we used to before.
Signed-off-by: Shlomo Pongratz <shlomop@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Take advantage of the matching macros to make the device id
list easier to read and maintain.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add 6 new devices and one modified device, based on
information from laptop vendor Windows drivers.
Sony provides a driver with two new devices using
a Gobi 2k+ layout (1199:68a5 and 1199:68a9). The
Sony driver also adds a non-standard QMI/net
interface to the already supported 1199:9011
Gobi device. We do not know whether this is an
alternate interface number or an additional
interface which might be present, but that doesn't
really matter.
Lenovo provides a driver supporting 4 new devices:
- MC7770 (1199:901b) with standard Gobi 2k+ layout
- MC7700 (0f3d:68a2) with layout similar to MC7710
- MC7750 (114f:68a2) with layout similar to MC7710
- EM7700 (1199:901c) with layout similar to MC7710
Note regaring the three devices similar to MC7710:
The Windows drivers only support interface #8 on these
devices. The MC7710 can support QMI/net functions on
interface #19 and #20 as well, and this driver is
verified to work on interface #19 (a firmware bug is
suspected to prevent #20 from working).
We do not enable these additional interfaces until they
either show up in a Windows driver or are verified to
work in some other way. Therefore limiting the new
devices to interface #8 for now.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver support many composite USB devices where the
interface class/subclass/protocol provides no information
about the interface function. Interfaces with different
functions may all use ff/ff/ff, like this example of
a device with three serial interfaces and three QMI/wwan
interfaces:
T: Bus=02 Lev=01 Prnt=01 Port=03 Cnt=01 Dev#=116 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=1199 ProdID=68a2 Rev= 0.06
S: Manufacturer=Sierra Wireless, Incorporated
S: Product=MC7710
S: SerialNumber=3581780xxxxxx
C:* #Ifs= 6 Cfg#= 1 Atr=e0 MxPwr= 0mA
I:* If#= 0 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qcserial
E: Ad=83(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#= 8 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=85(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#=19 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
E: Ad=87(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
I:* If#=20 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=2ms
E: Ad=8a(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=06(O) Atr=02(Bulk) MxPS= 512 Ivl=4ms
Instead of class/subclass/protocol the vendor use fixed
interface numbers for each function, and the Windows
drivers use these numbers to match driver and function.
The driver has had its own interface number whitelisting
code to simulate this functionality. Replace this with
generic interface number matching now that the USB subsystem
support is there. This
- removes the need for a driver_info structure per
interface number,
- avoids running the probe function for unsupported
interfaces, and
- simplifies the code.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
Although this doesn't matter actually, because netpoll_tx_running()
doesn't use the parameter, the code will be more readable.
For team_dev_queue_xmit() we have to move it down to avoid
compile errors.
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
With the previous patch applied, __netpoll_cleanup() is non-block now,
so we don't need to release the spin_lock before calling it.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like the previous patch, slave_disable_netpoll() and __netpoll_cleanup()
may be called with read_lock() held too, so we should make them
non-block, by moving the cleanup and kfree() to call_rcu_bh() callbacks.
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
slave_enable_netpoll() and __netpoll_setup() may be called
with read_lock() held, so should use GFP_ATOMIC to allocate
memory. Eric suggested to pass gfp flags to __netpoll_setup().
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: "David S. Miller" <davem@davemloft.net>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Cong Wang <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit "TTY: synclink_cs, use dynamic tty devices" added a call to
tty_port_register_device with a proper device as the last argument.
But it was not correct and it causes build failures:
synclink_cs.c: In function ‘mgslpc_add_device’:
synclink_cs.c:2735:16: error: request for member ‘dev’ in something not a structure or union
info->p_dev is a pointer, so act as that.
I wonder why my build scripts did not notice. I have to re-check them.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
When invalidating the TLBs it is documentated as requiring a post-sync
write. Failure to do so seems to result in a GPU hang.
Exposure to this hang on IVB seems to be a result of removing the extra
stalls required for SNB pipecontrol workarounds:
commit 6c6cf5aa9c
Author: Chris Wilson <chris@chris-wilson.co.uk>
Date: Fri Jul 20 18:02:28 2012 +0100
drm/i915: Only apply the SNB pipe control w/a to gen6
Note: Manually switch the pipe_control cmd to 4 dwords to avoid a
(silent) functional conflict with -next. This way will get a loud (but
conflict with next (since the scratch_addr has been deleted there).
Reported-and-tested-by: yex.tian@intel.com
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=53322
Acked-by: Ben Widawsky <ben@bwidawsk.net>
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
[danvet: added note about merge conflict with -next.]
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
eDP is tons of fun. It turns out that at least the new MacBook Air 5,1
model absolutely doesn't like the new force vdd dance we've introduced
in
commit 6cb49835da
Author: Daniel Vetter <daniel.vetter@ffwll.ch>
Date: Sun May 20 17:14:50 2012 +0200
drm/i915: enable vdd when switching off the eDP panel
But that patch also tried to fix some neat edp sequence issue with the
force_vdd timings. Closer inspection reveals that we've raised
force_vdd only to do the aux channel communication dp_sink_dpms. If we
move the edp_panel_off below that, we don't need any force_vdd for the
disable sequence, which makes the Air happy.
Unfortunately the reporter of the original bug that the above commit
fixed is travelling, so we can't test whether this regresses things.
But my theory is that since we don't check for any power-off ->
force_vdd-on delays in edp_panel_vdd_on, this was the actual
root-cause of this failure. With that force_vdd dance completely
eliminated, I'm hopeful the original bug stays fixed, too.
For reference the old bug, which hopefully doesn't get broken by this:
https://bugzilla.kernel.org/show_bug.cgi?id=43163
In any case, regression fixers win over plain bugfixes, so this needs
to go in asap.
v2: The crucial pieces seems to be to clear the force_vdd flag
uncoditionally, too, in edp_panel_off. Looks like this is left behind
by the firmware somehow.
v3: The Apple firmware seems to switch off the panel on it's own, hence
we still need to keep force_vdd on, but properly clear it when switching
the panel off.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=45671
Tested-by: Roberto Romer <sildurin@gmail.com>
Tested-by: Daniel Wagner <wagi@monom.org>
Tested-by: Keith Packard <keithp@keithp.com>
Cc: stable@vger.kernel.org
Cc: Keith Packard <keithp@keithp.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>