Netlink message lengths can't be negative, so use unsigned variables.
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch fixes a refcount leak of ct objects that may occur if
l4proto->error() assigns one conntrack object to one skbuff. In
that case, we have to skip further processing in nf_conntrack_in().
With this patch, we can also fix wrong return values (-NF_ACCEPT)
for special cases in ICMP[v6] that should not bump the invalid/error
statistic counters.
Reported-by: Zoltan Menyhart <Zoltan.Menyhart@bull.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Fix crash in nf_nat_csum when mangling packets
in OUTPUT hook where skb->dev is not defined, it is set
later before POSTROUTING. Problem happens for CHECKSUM_NONE.
We can check device from rt but using CHECKSUM_PARTIAL
should be safe (skb_checksum_help).
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Following error is raised (and other similar ones) :
net/ipv4/netfilter/nf_nat_standalone.c: In function ‘nf_nat_fn’:
net/ipv4/netfilter/nf_nat_standalone.c:119:2: warning: case value ‘4’
not in enumerated type ‘enum ip_conntrack_info’
gcc barfs on adding two enum values and getting a not enumerated
result :
case IP_CT_RELATED+IP_CT_IS_REPLY:
Add missing enum values
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: David Miller <davem@davemloft.net>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (40 commits)
tg3: Fix tg3_skb_error_unmap()
net: tracepoint of net_dev_xmit sees freed skb and causes panic
drivers/net/can/flexcan.c: add missing clk_put
net: dm9000: Get the chip in a known good state before enabling interrupts
drivers/net/davinci_emac.c: add missing clk_put
af-packet: Add flag to distinguish VID 0 from no-vlan.
caif: Fix race when conditionally taking rtnl lock
usbnet/cdc_ncm: add missing .reset_resume hook
vlan: fix typo in vlan_dev_hard_start_xmit()
net/ipv4: Check for mistakenly passed in non-IPv4 address
iwl4965: correctly validate temperature value
bluetooth l2cap: fix locking in l2cap_global_chan_by_psm
ath9k: fix two more bugs in tx power
cfg80211: don't drop p2p probe responses
Revert "net: fix section mismatches"
drivers/net/usb/catc.c: Fix potential deadlock in catc_ctrl_run()
sctp: stop pending timers and purge queues when peer restart asoc
drivers/net: ks8842 Fix crash on received packet when in PIO mode.
ip_options_compile: properly handle unaligned pointer
iwlagn: fix incorrect PCI subsystem id for 6150 devices
...
Check against mistakenly passing in IPv6 addresses (which would result
in an INADDR_ANY bind) or similar incompatible sockaddrs.
Signed-off-by: Marcus Meissner <meissner@suse.de>
Cc: Reinhard Max <max@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code takes an unaligned pointer and does htonl() on it to
make it big-endian, then does a memcpy(). The problem is that the
compiler decides that since the pointer is to a __be32, it is legal
to optimize the copy into a processor word store. However, on an
architecture that does not handled unaligned writes in kernel space,
this produces an unaligned exception fault.
The solution is to track the pointer as a "char *" (which removes a bunch
of unpleasant casts in any case), and then just use put_unaligned_be32()
to write the value to memory.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Signed-off-by: David S. Miller <davem@zippy.davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
net: Kill ratelimit.h dependency in linux/net.h
net: Add linux/sysctl.h includes where needed.
net: Kill ether_table[] declaration.
inetpeer: fix race in unused_list manipulations
atm: expose ATM device index in sysfs
IPVS: bug in ip_vs_ftp, same list heaad used in all netns.
bug.h: Move ratelimit warn interfaces to ratelimit.h
bonding: cleanup module option descriptions
net:8021q:vlan.c Fix pr_info to just give the vlan fullname and version.
net: davinci_emac: fix dev_err use at probe
can: convert to %pK for kptr_restrict support
net: fix ETHTOOL_SFEATURES compatibility with old ethtool_ops.set_flags
netfilter: Fix several warnings in compat_mtw_from_user().
netfilter: ipset: fix ip_set_flush return code
netfilter: ipset: remove unused variable from type_pf_tdel()
netfilter: ipset: Use proper timeout value to jiffies conversion
Several crashes in cleanup_once() were reported in recent kernels.
Commit d6cc1d642d (inetpeer: various changes) added a race in
unlink_from_unused().
One way to avoid taking unused_peers.lock before doing the list_empty()
test is to catch 0->1 refcnt transitions, using full barrier atomic
operations variants (atomic_cmpxchg() and atomic_inc_return()) instead
of previous atomic_inc() and atomic_add_unless() variants.
We then call unlink_from_unused() only for the owner of the 0->1
transition.
Add a new atomic_add_unless_return() static helper
With help from Arun Sharma.
Refs: https://bugzilla.kernel.org/show_bug.cgi?id=32772
Reported-by: Arun Sharma <asharma@fb.com>
Reported-by: Maximilian Engelhardt <maxi@daemonizer.de>
Reported-by: Yann Dupont <Yann.Dupont@univ-nantes.fr>
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'core-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
seqlock: Get rid of SEQLOCK_UNLOCKED
* 'irq-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
irq: Remove smp_affinity_list when unregister irq proc
In igmp_group_dropped() we call ip_mc_clear_src(), which resets the number
of source filters per mulitcast. However, igmp_group_dropped() is also
called on NETDEV_DOWN, NETDEV_PRE_TYPE_CHANGE and NETDEV_UNREGISTER, which
means that the group might get added back on NETDEV_UP, NETDEV_REGISTER and
NETDEV_POST_TYPE_CHANGE respectively, leaving us with broken source
filters.
To fix that, we must clear the source filters only when there are no users
in the ip_mc_list, i.e. in ip_mc_dec_group() and on device destroy.
Acked-by: David L Stevens <dlstevens@us.ibm.com>
Signed-off-by: Veaceslav Falico <vfalico@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
All static seqlock should be initialized with the lockdep friendly
__SEQLOCK_UNLOCKED() macro.
Remove legacy SEQLOCK_UNLOCKED() macro.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: David Miller <davem@davemloft.net>
Link: http://lkml.kernel.org/r/%3C1306238888.3026.31.camel%40edumazet-laptop%3E
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The %pK format specifier is designed to hide exposed kernel pointers,
specifically via /proc interfaces. Exposing these pointers provides an
easy target for kernel write vulnerabilities, since they reveal the
locations of writable structures containing easily triggerable function
pointers. The behavior of %pK depends on the kptr_restrict sysctl.
If kptr_restrict is set to 0, no deviation from the standard %p behavior
occurs. If kptr_restrict is set to 1, the default, if the current user
(intended to be a reader via seq_printf(), etc.) does not have CAP_SYSLOG
(currently in the LSM tree), kernel pointers using %pK are printed as 0's.
If kptr_restrict is set to 2, kernel pointers using %pK are printed as
0's regardless of privileges. Replacing with 0's was chosen over the
default "(null)", which cannot be parsed by userland %p, which expects
"(nil)".
The supporting code for kptr_restrict and %pK are currently in the -mm
tree. This patch converts users of %p in net/ to %pK. Cases of printing
pointers to the syslog are not covered, since this would eliminate useful
information for postmortem debugging and the reading of the syslog is
already optionally protected by the dmesg_restrict sysctl.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Cc: James Morris <jmorris@namei.org>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Thomas Graf <tgraf@infradead.org>
Cc: Eugene Teo <eugeneteo@kernel.org>
Cc: Kees Cook <kees.cook@canonical.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: David S. Miller <davem@davemloft.net>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Eric Paris <eparis@parisplace.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv4/ping.c: In function ‘ping_v4_unhash’:
net/ipv4/ping.c:140:28: warning: variable ‘hslot’ set but not used
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (27 commits)
bnx2x: allow device properly initialize after hotplug
bnx2x: fix DMAE timeout according to hw specifications
bnx2x: properly handle CFC DEL in cnic flow
bnx2x: call dev_kfree_skb_any instead of dev_kfree_skb
net: filter: move forward declarations to avoid compile warnings
pktgen: refactor pg_init() code
pktgen: use vzalloc_node() instead of vmalloc_node() + memset()
net: skb_trim explicitely check the linearity instead of data_len
ipv4: Give backtrace in ip_rt_bug().
net: avoid synchronize_rcu() in dev_deactivate_many
net: remove synchronize_net() from netdev_set_master()
rtnetlink: ignore NETDEV_RELEASE and NETDEV_JOIN event
net: rename NETDEV_BONDING_DESLAVE to NETDEV_RELEASE
bridge: call NETDEV_JOIN notifiers when add a slave
netpoll: disable netpoll when enslave a device
macvlan: Forward unicast frames in bridge mode to lowerdev
net: Remove linux/prefetch.h include from linux/skbuff.h
ipv4: Include linux/prefetch.h in fib_trie.c
netlabel: Remove prefetches from list handlers.
drivers/net: add prefetch header for prefetch users
...
Fixed up prefetch parts: removed a few duplicate prefetch.h includes,
fixed the location of the igb prefetch.h, took my version of the
skbuff.h code without the extra parentheses etc.
After discovering that wide use of prefetch on modern CPUs
could be a net loss instead of a win, net drivers which were
relying on the implicit inclusion of prefetch.h via the list
headers showed up in the resulting cleanup fallout. Give
them an explicit include via the following $0.02 script.
=========================================
#!/bin/bash
MANUAL=""
for i in `git grep -l 'prefetch(.*)' .` ; do
grep -q '<linux/prefetch.h>' $i
if [ $? = 0 ] ; then
continue
fi
( echo '?^#include <linux/?a'
echo '#include <linux/prefetch.h>'
echo .
echo w
echo q
) | ed -s $i > /dev/null 2>&1
if [ $? != 0 ]; then
echo $i needs manual fixup
MANUAL="$i $MANUAL"
fi
done
echo ------------------- 8\<----------------------
echo vi $MANUAL
=========================================
Signed-off-by: Paul <paul.gortmaker@windriver.com>
[ Fixed up some incorrect #include placements, and added some
non-network drivers and the fib_trie.c case - Linus ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a stack backtrace to the ip_rt_bug path for debugging
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1446 commits)
macvlan: fix panic if lowerdev in a bond
tg3: Add braces around 5906 workaround.
tg3: Fix NETIF_F_LOOPBACK error
macvlan: remove one synchronize_rcu() call
networking: NET_CLS_ROUTE4 depends on INET
irda: Fix error propagation in ircomm_lmp_connect_response()
irda: Kill set but unused variable 'bytes' in irlan_check_command_param()
irda: Kill set but unused variable 'clen' in ircomm_connect_indication()
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_transport()
be2net: Kill set but unused variable 'req' in lancer_fw_download()
irda: Kill set but unused vars 'saddr' and 'daddr' in irlan_provider_connect_indication()
atl1c: atl1c_resume() is only used when CONFIG_PM_SLEEP is defined.
rxrpc: Fix set but unused variable 'usage' in rxrpc_get_peer().
rxrpc: Kill set but unused variable 'local' in rxrpc_UDP_error_handler()
rxrpc: Kill set but unused variable 'sp' in rxrpc_process_connection()
rxrpc: Kill set but unused variable 'sp' in rxrpc_rotate_tx_window()
pkt_sched: Kill set but unused variable 'protocol' in tc_classify()
isdn: capi: Use pr_debug() instead of ifdefs.
tg3: Update version to 3.119
tg3: Apply rx_discards fix to 5719/5720
...
Fix up trivial conflicts in arch/x86/Kconfig and net/mac80211/agg-tx.c
as per Davem.
v3 -> v4: fix return boolean false instead of 0 for ic_is_init_dev
Currently the ip auto configuration has a hardcoded delay of 1 second.
When (ethernet) link takes longer to come up (e.g. more than 3 seconds),
nfs root may not be found.
Remove the hardcoded delay, and wait for carrier on at least one network
device.
Signed-off-by: Micha Nelissen <micha@neli.hopto.org>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The characters in a line should be no more than 80.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It's way past it's usefulness. And this gets rid of a bunch
of stray ->rt_{dst,src} references.
Even the comment documenting the macro was inaccurate (stated
default was 1 when it's 0).
If reintroduced, it should be done properly, with dynamic debug
facilities.
Signed-off-by: David S. Miller <davem@davemloft.net>
If CONFIG_PROC_SYSCTL=n the building process fails:
ping.c:(.text+0x52af3): undefined reference to `inet_get_ping_group_range_net'
Moved inet_get_ping_group_range_net() to ping.c.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 6623e3b24a (ipv4: IP defragmentation must be ECN aware) was an
attempt to not lose "Congestion Experienced" (CE) indications when
performing datagram defragmentation.
Stefanos Harhalakis raised the point that RFC 3168 requirements were not
completely met by this commit.
In particular, we MUST detect invalid combinations and eventually drop
illegal frames.
Reported-by: Stefanos Harhalakis <v13@v13.gr>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
udp_ioctl() really handles UDP and UDPLite protocols.
1) It can increment UDP_MIB_INERRORS in case first_packet_length() finds
a frame with bad checksum.
2) It has a dependency on sizeof(struct udphdr), not applicable to
ICMP/PING
If ping sockets need to handle SIOCINQ/SIOCOUTQ ioctl, this should be
done differently.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ping_table is not __read_mostly, since it contains one rwlock,
and is static to ping.c
ping_port_rover & ping_v4_lookup are static
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pass in the sk_buff so that we can fetch the necessary keys from
the packet header when working with input routes.
Signed-off-by: David S. Miller <davem@davemloft.net>
This code block executes when opt->srr_is_hit is set. It will be
set only by ip_options_rcv_srr().
ip_options_rcv_srr() walks until it hits a matching nexthop in the SRR
option addresses, and when it matches one 1) looks up the route for
that nexthop and 2) on route lookup success it writes that nexthop
value into iph->daddr.
ip_forward_options() runs later, and again walks the SRR option
addresses looking for the option matching the destination of the route
stored in skb_rtable(). This route will be the same exact one looked
up for the nexthop by ip_options_rcv_srr().
Therefore "rt->rt_dst == iph->daddr" must be true.
All it really needs to do is record the route's source address in the
matching SRR option adddress. It need not write iph->daddr again,
since that has already been done by ip_options_rcv_srr() as detailed
above.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IPPROTO_ICMP socket kind. It makes it possible to send
ICMP_ECHO messages and receive the corresponding ICMP_ECHOREPLY messages
without any special privileges. In other words, the patch makes it
possible to implement setuid-less and CAP_NET_RAW-less /bin/ping. In
order not to increase the kernel's attack surface, the new functionality
is disabled by default, but is enabled at bootup by supporting Linux
distributions, optionally with restriction to a group or a group range
(see below).
Similar functionality is implemented in Mac OS X:
http://www.manpagez.com/man/4/icmp/
A new ping socket is created with
socket(PF_INET, SOCK_DGRAM, PROT_ICMP)
Message identifiers (octets 4-5 of ICMP header) are interpreted as local
ports. Addresses are stored in struct sockaddr_in. No port numbers are
reserved for privileged processes, port 0 is reserved for API ("let the
kernel pick a free number"). There is no notion of remote ports, remote
port numbers provided by the user (e.g. in connect()) are ignored.
Data sent and received include ICMP headers. This is deliberate to:
1) Avoid the need to transport headers values like sequence numbers by
other means.
2) Make it easier to port existing programs using raw sockets.
ICMP headers given to send() are checked and sanitized. The type must be
ICMP_ECHO and the code must be zero (future extensions might relax this,
see below). The id is set to the number (local port) of the socket, the
checksum is always recomputed.
ICMP reply packets received from the network are demultiplexed according
to their id's, and are returned by recv() without any modifications.
IP header information and ICMP errors of those packets may be obtained
via ancillary data (IP_RECVTTL, IP_RETOPTS, and IP_RECVERR). ICMP source
quenches and redirects are reported as fake errors via the error queue
(IP_RECVERR); the next hop address for redirects is saved to ee_info (in
network order).
socket(2) is restricted to the group range specified in
"/proc/sys/net/ipv4/ping_group_range". It is "1 0" by default, meaning
that nobody (not even root) may create ping sockets. Setting it to "100
100" would grant permissions to the single group (to either make
/sbin/ping g+s and owned by this group or to grant permissions to the
"netadmins" group), "0 4294967295" would enable it for the world, "100
4294967295" would enable it for the users, but not daemons.
The existing code might be (in the unlikely case anyone needs it)
extended rather easily to handle other similar pairs of ICMP messages
(Timestamp/Reply, Information Request/Reply, Address Mask Request/Reply
etc.).
Userspace ping util & patch for it:
http://openwall.info/wiki/people/segoon/ping
For Openwall GNU/*/Linux it was the last step on the road to the
setuid-less distro. A revision of this patch (for RHEL5/OpenVZ kernels)
is in use in Owl-current, such as in the 2011/03/12 LiveCD ISOs:
http://mirrors.kernel.org/openwall/Owl/current/iso/
Initially this functionality was written by Pavel Kankovsky for
Linux 2.4.32, but unfortunately it was never made public.
All ping options (-b, -p, -Q, -R, -s, -t, -T, -M, -I), are tested with
the patch.
PATCH v3:
- switched to flowi4.
- minor changes to be consistent with raw sockets code.
PATCH v2:
- changed ping_debug() to pr_debug().
- removed CONFIG_IP_PING.
- removed ping_seq_fops.owner field (unused for procfs).
- switched to proc_net_fops_create().
- switched to %pK in seq_printf().
PATCH v1:
- fixed checksumming bug.
- CAP_NET_RAW may not create icmp sockets anymore.
RFC v2:
- minor cleanups.
- introduced sysctl'able group range to restrict socket(2).
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
I swear none of my compilers warned about this, yet it is so
obvious.
> net/ipv4/ip_forward.c: In function 'ip_forward':
> net/ipv4/ip_forward.c:87: warning: 'iph' may be used uninitialized in this function
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
No matter what kind of header mangling occurs due to IP options
processing, rt->rt_dst will always equal iph->daddr in the packet.
So we can safely use iph->daddr instead of rt->rt_dst here.
Signed-off-by: David S. Miller <davem@davemloft.net>
We already copy the 4-byte nexthop from the options block into
local variable "nexthop" for the route lookup.
Re-use that variable instead of memcpy()'ing again when assigning
to iph->daddr after the route lookup succeeds.
Signed-off-by: David S. Miller <davem@davemloft.net>
All call sites conditionalize the call to ip_options_rcv_srr()
with a check of opt->srr, so no need to check it again there.
Signed-off-by: David S. Miller <davem@davemloft.net>
As it is, we assign the outer modes output function to the dst entry
when we create the xfrm bundle. This leads to two problems on interfamily
scenarios. We might insert ipv4 packets into ip6_fragment when called
from xfrm6_output. The system crashes if we try to fragment an ipv4
packet with ip6_fragment. This issue was introduced with git commit
ad0081e4 (ipv6: Fragment locally generated tunnel-mode IPSec6 packets
as needed). The second issue is, that we might insert ipv4 packets in
netfilter6 and vice versa on interfamily scenarios.
With this patch we assign the inner mode output function to the dst entry
when we create the xfrm bundle. So xfrm4_output/xfrm6_output from the inner
mode is used and the right fragmentation and netfilter functions are called.
We switch then to outer mode with the output_finish functions.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit e67f88dd12 (net: dont hold rtnl mutex during netlink dump
callbacks) switched rtnl protection to RCU, but we forgot to adjust two
rcu_dereference() lockdep annotations :
inet_get_link_af_size() or inet_fill_link_af() might be called with
rcu_read_lock or rtnl held, so use rcu_dereference_rtnl()
instead of rtnl_dereference()
Reported-by: Valdis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rearrange xfrm4_dst_lookup() so that it works by calling a helper
function __xfrm_dst_lookup() that takes an explicit flow key storage
area as an argument.
Use this new helper in xfrm4_get_saddr() so we can fetch the selected
source address from the flow instead of from rt->rt_src
Signed-off-by: David S. Miller <davem@davemloft.net>
On input packets, rt->rt_src always equals ip_hdr(skb)->saddr
Anything that mangles or otherwise changes the IP header must
relookup the route found at skb_rtable(). Therefore this
invariant must always hold true.
Signed-off-by: David S. Miller <davem@davemloft.net>
This way ip_output.c no longer needs rt->rt_{src,dst}.
We already have these keys sitting, ready and waiting, on the stack or
in a socket structure.
Signed-off-by: David S. Miller <davem@davemloft.net>
We have two cases.
Either the socket is in TCP_ESTABLISHED state and connect() filled
in the inet socket cork flow, or we looked up the route here and
used an on-stack flow.
Track which one it was, and use it to obtain src/dst addrs.
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP Cubic keeps a metric that estimates the amount of delayed
acknowledgements to use in adjusting the window. If an abnormally
large number of packets are acknowledged at once, then the update
could wrap and reach zero. This kind of ACK could only
happen when there was a large window and huge number of
ACK's were lost.
This patch limits the value of delayed ack ratio. The choice of 32
is just a conservative value since normally it should be range of
1 to 4 packets.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows us to acquire the exact route keying information from the
protocol, however that might be managed.
It handles all of the possibilities, from the simplest case of storing
the key in inet->cork.fl to the more complex setup SCTP has where
individual transports determine the flow.
Signed-off-by: David S. Miller <davem@davemloft.net>
Operation order is now transposed, we first create the child
socket then we try to hook up the route.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is just like inet_csk_route_req() except that it operates after
we've created the new child socket.
In this way we can use the new socket's cork flow for proper route
key storage.
This will be used by DCCP and TCP child socket creation handling.
Signed-off-by: David S. Miller <davem@davemloft.net>
All invokers of ip_queue_xmit() must make certain that the
socket is locked. All of SCTP, TCP, DCCP, and L2TP now make
sure this is the case.
Therefore we can use the cork flow during output route lookup in
ip_queue_xmit() when the socket route check fails.
Signed-off-by: David S. Miller <davem@davemloft.net>
These two functions must be invoked only when the socket is locked
(because socket identity modifications are made non-atomically).
Therefore we can use the cork flow for output route lookups.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is to make sure that an l2tp socket's inet cork flow is
fully filled in, when it's encapsulated in UDP.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since this is invoked from inet_stream_connect() the socket is locked
and therefore this usage is safe.
Signed-off-by: David S. Miller <davem@davemloft.net>
The rcu callback ip_mc_socklist_reclaim() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(ip_mc_socklist_reclaim).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The rcu callback ip_sf_socklist_reclaim() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(ip_sf_socklist_reclaim).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The rcu callback ip_mc_list_reclaim() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(ip_mc_list_reclaim).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The rcu callback __leaf_info_free_rcu() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(__leaf_info_free_rcu).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
The rcu callback fc_rport_free_rcu() just calls a kfree(),
so we use kfree_rcu() instead of the call_rcu(fc_rport_free_rcu).
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Reviewed-by: Josh Triplett <josh@joshtriplett.org>
ip_setup_cork() explicitly initializes every member of
inet_cork except flags, addr, and opt. So we can simply
set those three members to zero instead of using a
memset() via an empty struct assignment.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
When we fast path datagram sends to avoid locking by putting
the inet_cork on the stack we use up lots of space that isn't
necessary.
This is because inet_cork contains a "struct flowi" which isn't
used in these code paths.
Split inet_cork to two parts, "inet_cork" and "inet_cork_full".
Only the latter of which has the "struct flowi" and is what is
stored in inet_sock.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Force dev_alloc_name() to be called from register_netdevice() by
dev_get_valid_name(). That allows to remove multiple explicit
dev_alloc_name() calls.
The possibility to call dev_alloc_name in advance remains.
This also fixes veth creation regresion caused by
84c49d8c3e
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 4a94445c9a (net: Use ip_route_input_noref() in input path)
added a bug in IP defragmentation handling, in case timeout is fired.
When a frame is defragmented, we use last skb dst field when building
final skb. Its dst is valid, since we are in rcu read section.
But if a timeout occurs, we take first queued fragment to build one ICMP
TIME EXCEEDED message. Problem is all queued skb have weak dst pointers,
since we escaped RCU critical section after their queueing. icmp_send()
might dereference a now freed (and possibly reused) part of memory.
Calling skb_dst_drop() and ip_route_input_noref() to revalidate route is
the only possible choice.
Reported-by: Denys Fedoryshchenko <denys@visp.net.lb>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First, make callers pass on-stack flowi4 to ip_route_output_gre()
so they can get at the fully resolved flow key.
Next, use that in ipgre_tunnel_xmit() to avoid the need to use
rt->rt_{dst,src}.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of rt->rt_{dst,src}
The only tricky part is source route option handling.
If the source route option is enabled we can't just use plain 'daddr',
we have to use opt->opt.faddr.
Signed-off-by: David S. Miller <davem@davemloft.net>
To more accurately reflect that it is purely a routing
cache lookup key and is used in no other context.
Signed-off-by: David S. Miller <davem@davemloft.net>
ctl_table_headers registered with register_net_sysctl_table should
have been unregistered with the equivalent unregister_net_sysctl_table
Signed-off-by: Lucian Adrian Grijincu <lucian.grijincu@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Slow path output route resolution always makes sure that
->{saddr,daddr} are set, and also if we trigger into IPSEC resolution
we initialize them as well, because xfrm_lookup() expects them to be
fully resolved.
But if we hit the fast path and flowi4->flowi4_proto is zero, we won't
do this initialization.
Therefore, move the IPSEC path initialization to the route cache
lookup fast path to make sure these are always set.
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_trie_table() is called during netns creation and
Chromium uses clone(CLONE_NEWNET) to sandbox renderer process.
Don't print anything.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For backward compatibility, we should retain the module parameters and
sysfs attributes to control the number of peer notifications
(gratuitous ARPs and unsolicited NAs) sent after bonding failover.
Also, it is possible for failover to take place even though the new
active slave does not have link up, and in that case the peer
notification should be deferred until it does.
Change ipv4 and ipv6 so they do not automatically send peer
notifications on bonding failover.
Change the bonding driver to send separate NETDEV_NOTIFY_PEERS
notifications when the link is up, as many times as requested. Since
it does not directly control which protocols send notifications, make
num_grat_arp and num_unsol_na aliases for a single parameter. Bump
the bonding version number and update its documentation.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jay Vosburgh <fubar@us.ibm.com>
Acked-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that output route lookups update the flow with
destination address selection, we can fetch it from
fl4->daddr instead of rt->rt_dst
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that output route lookups update the flow with
source address selection, we can fetch it from
fl4->saddr instead of rt->rt_src
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that output route lookups update the flow with
source address selection, we can fetch it from
fl4->saddr instead of rt->rt_src
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that output route lookups update the flow with
source address selection, we can fetch it from
fl4->saddr instead of rt->rt_src
Signed-off-by: David S. Miller <davem@davemloft.net>
Make dst_alloc() and it's users explicitly initialize the entire
entry.
The zero'ing done by kmem_cache_zalloc() was almost entirely
redundant.
Signed-off-by: David S. Miller <davem@davemloft.net>
We lack proper synchronization to manipulate inet->opt ip_options
Problem is ip_make_skb() calls ip_setup_cork() and
ip_setup_cork() possibly makes a copy of ipc->opt (struct ip_options),
without any protection against another thread manipulating inet->opt.
Another thread can change inet->opt pointer and free old one under us.
Use RCU to protect inet->opt (changed to inet->inet_opt).
Instead of handling atomic refcounts, just copy ip_options when
necessary, to avoid cache line dirtying.
We cant insert an rcu_head in struct ip_options since its included in
skb->cb[], so this patch is large because I had to introduce a new
ip_options_rcu structure.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Output route resolution never returns a route with rt_src set to zero
(which is INADDR_ANY).
Even if the flow key for the output route lookup specifies INADDR_ANY
for the source address, the output route resolution chooses a real
source address to use in the final route.
This test has existed forever in igmp_send_report() and David Stevens
simply copied over the erroneous test when implementing support for
IGMPv3.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
These functions are used together as a unit for route resolution
during connect(). They address the chicken-and-egg problem that
exists when ports need to be allocated during connect() processing,
yet such port allocations require addressing information from the
routing code.
It's currently more heavy handed than it needs to be, and in
particular we allocate and initialize a flow object twice.
Let the callers provide the on-stack flow object. That way we only
need to initialize it once in the ip_route_connect() call.
Later, if ip_route_newports() needs to do anything, it re-uses that
flow object as-is except for the ports which it updates before the
route re-lookup.
Also, describe why this set of facilities are needed and how it works
in a big comment.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
Resolved logic conflicts causing a build failure due to
drivers/net/r8169.c changes using a patch from Stephen Rothwell.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add const qualifiers to structs iphdr, ipv6hdr and in6_addr pointers
where possible, to make code intention more obvious.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is undesirable for the bonding driver to be poking into higher
level protocols, and notifiers provide a way to avoid that. This does
mean removing the ability to configure reptitition of gratuitous ARPs
and unsolicited NAs.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Scot Doyle demonstrated ip_options_compile() could be called with an skb
without an attached route, using a setup involving a bridge, netfilter,
and forged IP packets.
Let's make ip_options_compile() and ip_options_rcv_srr() a bit more
robust, instead of changing bridge/netfilter code.
With help from Hiroaki SHIMODA.
Reported-by: Scot Doyle <lkml@scotdoyle.com>
Tested-by: Scot Doyle <lkml@scotdoyle.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_select_default() is a complete NOP, and completely pointless
to invoke, when we have no more than 1 default route installed.
And this is far and away the common case.
So remember how many prefixlen==0 routes we have in the routing
table, and elide the call when we have no more than one of those.
This cuts output route creation time by 157 cycles on Niagara2+.
In order to add the new int to fib_table, we have to correct the type
of ->tb_data[] to unsigned long, otherwise the private area will be
unaligned on 64-bit systems.
Signed-off-by: David S. Miller <davem@davemloft.net>
Reviewed-by: Eric Dumazet <eric.dumazet@gmail.com>
This reverts commit c191a836a9.
It causes known regressions for programs that expect to be able to use
SO_REUSEADDR to shutdown a socket, then successfully rebind another
socket to the same ID.
Programs such as haproxy and amavisd expect this to work.
This should fix kernel bugzilla 32832.
Signed-off-by: David S. Miller <davem@davemloft.net>
controlling igmp_max_membership is useful even when IP_MULTICAST
is off.
Quagga(an OSPF deamon) uses multicast addresses for all interfaces
using a single socket and hits igmp_max_membership limit when
there are 20 interfaces or more.
Always export sysctl igmp_max_memberships in proc, just like
igmp_max_msf
Signed-off-by: Joakim Tjernlund <Joakim.Tjernlund@transmode.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
net: Add support for SMSC LAN9530, LAN9730 and LAN89530
mlx4_en: Restoring RX buffer pointer in case of failure
mlx4: Sensing link type at device initialization
ipv4: Fix "Set rt->rt_iif more sanely on output routes."
MAINTAINERS: add entry for Xen network backend
be2net: Fix suspend/resume operation
be2net: Rename some struct members for clarity
pppoe: drop PPPOX_ZOMBIEs in pppoe_flush_dev
dsa/mv88e6131: add support for mv88e6085 switch
ipv6: Enable RFS sk_rxhash tracking for ipv6 sockets (v2)
be2net: Fix a potential crash during shutdown.
bna: Fix for handling firmware heartbeat failure
can: mcp251x: Allow pass IRQ flags through platform data.
smsc911x: fix mac_lock acquision before calling smsc911x_mac_read
iwlwifi: accept EEPROM version 0x423 for iwl6000
rt2x00: fix cancelling uninitialized work
rtlwifi: Fix some warnings/bugs
p54usb: IDs for two new devices
wl12xx: fix potential buffer overflow in testmode nvs push
zd1211rw: reset rx idle timer from tasklet
...
The reverse path filter interferes with IPsec subnet-to-subnet tunnels,
especially when the link to the IPsec peer is on an interface other than
the one hosting the default route.
With dynamic routing, where the peer might be reachable through eth0
today and eth1 tomorrow, it's difficult to keep rp_filter enabled unless
fake routes to the remote subnets are configured on the interface
currently used to reach the peer.
IPsec provides a much stronger anti-spoofing policy than rp_filter, so
this patch disables the rp_filter for packets with a security path.
Signed-off-by: Michael Smith <msmith@cbnco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This makes sk_buff available for other use in fib_validate_source().
Signed-off-by: Michael Smith <msmith@cbnco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 1018b5c016 ("Set rt->rt_iif more
sanely on output routes.") breaks rt_is_{output,input}_route.
This became the cause to return "IP_PKTINFO's ->ipi_ifindex == 0".
To fix it, this does:
1) Add "int rt_route_iif;" to struct rtable
2) For input routes, always set rt_route_iif to same value as rt_iif
3) For output routes, always set rt_route_iif to zero. Set rt_iif
as it is done currently.
4) Change rt_is_{output,input}_route() to test rt_route_iif
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch uses __copy_from_user_nocache on transmit to bypass data
cache for a performance improvement. skb_add_data_nocache and
skb_copy_to_page_nocache can be called by sendmsg functions to use
this feature, initial support is in tcp_sendmsg. This functionality is
configurable per device using ethtool.
Presumably, this feature would only be useful when the driver does
not touch the data. The feature is turned on by default if a device
indicates that it does some form of checksum offload; it is off by
default for devices that do no checksum offload or indicate no checksum
is necessary. For the former case copy-checksum is probably done
anyway, in the latter case the device is likely loopback in which case
the no cache copy is probably not beneficial.
This patch was tested using 200 instances of netperf TCP_RR with
1400 byte request and one byte reply. Platform is 16 core AMD x86.
No-cache copy disabled:
672703 tps, 97.13% utilization
50/90/99% latency:244.31 484.205 1028.41
No-cache copy enabled:
702113 tps, 96.16% utilization,
50/90/99% latency 238.56 467.56 956.955
Using 14000 byte request and response sizes demonstrate the
effects more dramatically:
No-cache copy disabled:
79571 tps, 34.34 %utlization
50/90/95% latency 1584.46 2319.59 5001.76
No-cache copy enabled:
83856 tps, 34.81% utilization
50/90/95% latency 2508.42 2622.62 2735.88
Note especially the effect on latency tail (95th percentile).
This seems to provide a nice performance improvement and is
consistent in the tests I ran. Presumably, this would provide
the greatest benfits in the presence of an application workload
stressing the cache and a lot of transmit data happening.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We currently use a percpu spinlock to 'protect' rule bytes/packets
counters, after various attempts to use RCU instead.
Lately we added a seqlock so that get_counters() can run without
blocking BH or 'writers'. But we really only need the seqcount in it.
Spinlock itself is only locked by the current/owner cpu, so we can
remove it completely.
This cleanups api, using correct 'writer' vs 'reader' semantic.
At replace time, the get_counters() call makes sure all cpus are done
using the old table.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
ipv6 fib lookup can set RT6_LOOKUP_F_IFACE flag to restrict search
to an interface, but this flag cannot be set via struct flowi.
Also, it cannot be set via ip6_route_output: this function uses the
passed sock struct to determine if this flag is required
(by testing for nonzero sk_bound_dev_if).
Work around this by passing in an artificial struct sk in case
'strict' argument is true.
This is required to replace the rt6_lookup call in xt_addrtype.c with
nf_afinfo->route().
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This is required to eventually replace the rt6_lookup call in
xt_addrtype.c with nf_afinfo->route().
Signed-off-by: Florian Westphal <fw@strlen.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Patrick McHardy <kaber@trash.net>
All callers are prepared for alloc failures anyway, so this error
can safely be boomeranged to the callers domain without super
bad consequences. ...At worst the connection might go into a state
where each RTO tries to (unsuccessfully) re-fragment with such
a mis-sized value and eventually dies.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __rcu annotations and lockdep checks.
Add const qualifiers
node_parent() and node_parent_rcu() can use
rcu_dereference_index_check()
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Daniel J Blueman reported a lockdep splat in trie_firstleaf(), caused by
RTNL being not locked before a call to fib_table_flush()
Reported-by: Daniel J Blueman <daniel.blueman@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
My commit 6d55cb91a0 (gre: fix hard header destination
address checking) broke multicast.
The reason is that ip_gre used to get ipgre_header() calls with
zero destination if we have NOARP or multicast destination. Instead
the actual target was decided at ipgre_tunnel_xmit() time based on
per-protocol dissection.
Instead of allowing the "abuse" of ->header() calls with invalid
destination, this creates multicast mappings for ip_gre. This also
fixes "ip neigh show nud noarp" to display the proper multicast
mappings used by the gre device.
Reported-by: Doug Kehn <rdkehn@yahoo.com>
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Acked-by: Doug Kehn <rdkehn@yahoo.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current handling of echoed IP timestamp options with prespecified
addresses is rather broken since the 2.2.x kernels. As far as i understand
it, it should behave like when originating packets.
Currently it will only timestamp the next free slot if:
- there is space for *two* timestamps
- some random data from the echoed packet taken as an IP is *not* a local IP
This first is caused by an off-by-one error. 'soffset' points to the next
free slot and so we only need to have 'soffset + 7 <= optlen'.
The second bug is using sptr as the start of the option, when it really is
set to 'skb_network_header(skb)'. I just use dptr instead which points to
the timestamp option.
Finally it would only timestamp for non-local IPs, which we shouldn't do.
So instead we exclude all unicast destinations, similar to what we do in
ip_options_compile().
Signed-off-by: Jan Luebbe <jluebbe@debian.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "ipv4: Inline fib_semantic_match into check_leaf"
change forgets to return the route errors. check_leaf should
return the same results as fib_table_lookup.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move the scope value out of the fib alias entries and into fib_info,
so that we always use the correct scope when recomputing the nexthop
cached source address.
Reported-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Any operation that:
1) Brings up an interface
2) Adds an IP address to an interface
3) Deletes an IP address from an interface
can potentially invalidate the nh_saddr value, requiring
it to be recomputed.
Perform the recomputation lazily using a generation ID.
Reported-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alessandro Suardi reported that we could not change route metrics :
ip ro change default .... advmss 1400
This regression came with commit 9c150e82ac (Allocate fib metrics
dynamically). fib_metrics is no longer an array, but a pointer to an
array.
Reported-by: Alessandro Suardi <alessandro.suardi@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Tested-by: Alessandro Suardi <alessandro.suardi@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 2c8cec5c10 (Cache learned PMTU information in inetpeer) added
an extra inet_putpeer() call in ip_rt_update_pmtu().
This results in various problems, since we can free one inetpeer, while
it is still in use.
Ref: http://www.spinics.net/lists/netdev/msg159121.html
Reported-by: Alexander Beregalov <a.beregalov@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit 9435eb1cf0
("ipv4: Implement __ip_dev_find using new interface address hash.")
we reimplemented __ip_dev_find() so that it doesn't have to
do a full FIB table lookup.
Instead, it consults a hash table of addresses configured to
interfaces.
This works identically to the old code in all except one case,
and that is for loopback subnets.
The old code would match the loopback device for any IP address
that falls within a subnet configured to the loopback device.
Handle this corner case by doing the FIB lookup.
We could implement this via inet_addr_onlink() but:
1) Someone could configure many addresses to loopback and
inet_addr_onlink() is a simple list traversal.
2) We know the old code works.
Reported-by: Julian Anastasov <ja@ssi.bg>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current undo logic, cwnd is moderated after it was restored
to the value prior entering fast-recovery. It was moderated first
in tcp_try_undo_recovery then again in tcp_complete_cwr.
Since the undo indicates recovery was false, these moderations
are not necessary. If the undo is triggered when most of the
outstanding data have been acknowledged, the (restored) cwnd is
falsely pulled down to a small value.
This patch removes these cwnd moderations if cwnd is undone
a) during fast-recovery
b) by receiving DSACKs past fast-recovery
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Optimize the calling of fib_add_ifaddr for all
secondary addresses after the promoted one to start from
their place, not from the new place of the promoted
secondary. It will save some CPU cycles because we
are sure the promoted secondary was first for the subnet
and all next secondaries do not change their place.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
The secondary address promotion relies on fib_sync_down_addr
to remove all routes created for the secondary addresses when
the old primary address is deleted. It does not happen for cases
when the primary address is also in another subnet. Fix that
by deleting local and broadcast routes for all secondaries while
they are on device list and by faking that all addresses from
this subnet are to be deleted. It relies on fib_del_ifaddr being
able to ignore the IPs from the concerned subnet while checking
for duplication.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alex Sidorenko reported for problems with local
routes left after IP addresses are deleted. It happens
when same IPs are used in more than one subnet for the
device.
Fix fib_del_ifaddr to restrict the checks for duplicate
local and broadcast addresses only to the IFAs that use
our primary IFA or another primary IFA with same address.
And we expect the prefsrc to be matched when the routes
are deleted because it is possible they to differ only by
prefsrc. This patch prevents local and broadcast routes
to be leaked until their primary IP is deleted finally
from the box.
As the secondary address promotion needs to delete
the routes for all secondaries that used the old primary IFA,
add option to ignore these secondaries from the checks and
to assume they are already deleted, so that we can safely
delete the route while these IFAs are still on the device list.
Reported-by: Alex Sidorenko <alexandre.sidorenko@hp.com>
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_table_delete forgets to match the routes by prefsrc.
Callers can specify known IP in fc_prefsrc and we should remove
the exact route. This is needed for cases when same local or
broadcast addresses are used in different subnets and the
routes differ only in prefsrc. All callers that do not provide
fc_prefsrc will ignore the route prefsrc as before and will
delete the first occurence. That is how the ip route del default
magic works.
Current callers are:
- ip_rt_ioctl where rtentry_to_fib_config provides fc_prefsrc only
when the provided device name matches IP label with colon.
- inet_rtm_delroute where RTA_PREFSRC is optional too
- fib_magic which deals with routes when deleting addresses
and where the fc_prefsrc is always set with the primary IP
for the concerned IFA.
Signed-off-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
'buffer' string is copied from userspace. It is not checked whether it is
zero terminated. This may lead to overflow inside of simple_strtoul().
Changli Gao suggested to copy not more than user supplied 'size' bytes.
It was introduced before the git epoch. Files "ipt_CLUSTERIP/*" are
root writable only by default, however, on some setups permissions might be
relaxed to e.g. network admin user.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
commit f3c5c1bfd4 (make ip_tables reentrant) introduced a race in
handling the stackptr restore, at the end of ipt_do_table()
We should do it before the call to xt_info_rdunlock_bh(), or we allow
cpu preemption and another cpu overwrites stackptr of original one.
A second fix is to change the underflow test to check the origptr value
instead of 0 to detect underflow, or else we allow a jump from different
hooks.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
ECN support incorrectly maps ECN BESTEFFORT packets to TC_PRIO_FILLER
(1) instead of TC_PRIO_BESTEFFORT (0)
This means ECN enabled flows are placed in pfifo_fast/prio low priority
band, giving ECN enabled flows [ECT(0) and CE codepoints] higher drop
probabilities.
This is rather unfortunate, given we would like ECN being more widely
used.
Ref : http://www.coverfire.com/archives/2011/03/13/pfifo_fast-and-ecn/
Signed-off-by: Dan Siemon <dan@coverfire.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Dave Täht <d@taht.net>
Cc: Jonathan Morton <chromatix99@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup patch will add ipv6 support.
ipt_addrtype.h is retained for compatibility reasons, but no longer used
by the kernel.
Signed-off-by: Florian Westphal <fwestphal@astaro.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Structures ipt_replace, compat_ipt_replace, and xt_get_revision are
copied from userspace. Fields of these structs that are
zero-terminated strings are not checked. When they are used as argument
to a format string containing "%s" in request_module(), some sensitive
information is leaked to userspace via argument of spawned modprobe
process.
The first and the third bugs were introduced before the git epoch; the
second was introduced in 2722971c (v2.6.17-rc1). To trigger the bug
one should have CAP_NET_ADMIN.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Structures ipt_replace, compat_ipt_replace, and xt_get_revision are
copied from userspace. Fields of these structs that are
zero-terminated strings are not checked. When they are used as argument
to a format string containing "%s" in request_module(), some sensitive
information is leaked to userspace via argument of spawned modprobe
process.
The first bug was introduced before the git epoch; the second is
introduced by 6b7d31fc (v2.6.15-rc1); the third is introduced by
6b7d31fc (v2.6.15-rc1). To trigger the bug one should have
CAP_NET_ADMIN.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
HyStart sets the initial exit point of slow start.
Suppose that HyStart exits at 0.5BDP in a BDP network and no history exists.
If the BDP of a network is large, CUBIC's initial cwnd growth may be
too conservative to utilize the link.
CUBIC increases the cwnd 20% per RTT in this case.
Signed-off-by: Sangtae Ha <sangtae.ha@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make HyStart less sensitive to abrupt delay variations due to buffer bloat.
Signed-off-by: Sangtae Ha <sangtae.ha@gmail.com>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Reported-by: Lucas Nussbaum <lucas.nussbaum@loria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a refined version of an earlier patch by Lucas Nussbaum.
Cubic needs RTT values in milliseconds. If HZ < 1000 then
the values will be too coarse.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reported-by: Lucas Nussbaum <lucas.nussbaum@loria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hystart code was written with assumption that HZ=1000.
Replace the use of jiffies with bictcp_clock as a millisecond
real time clock.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Reported-by: Lucas Nussbaum <lucas.nussbaum@loria.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make the spacing between ACK's that indicates a train a tuneable
value like other hystart values.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiffies wraps around therefore the correct way to compare is
to use cast to signed value.
Note: cubic is not using full jiffies value on 64 bit arch
because using full unsigned long makes struct bictcp grow too
large for the available ca_priv area.
Includes correction from Sangtae Ha to improve ack train detection.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the congestion control interface, the callback for each ACK
includes an estimated round trip time in microseconds.
Some algorithms need high resolution (Vegas style) but most only
need jiffie resolution. If RTT is not accurate (like a retransmission)
-1 is used as a flag value.
When doing coarse resolution if RTT is less than a a jiffie
then 0 should be returned rather than no estimate. Otherwise algorithms
that expect good ack's to trigger slow start (like CUBIC Hystart)
will be confused.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit 7b46ac4e77 (inetpeer: Don't disable BH for initial
fast RCU lookup.), we should use call_rcu() to wait proper RCU grace
period.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds IPsec extended sequence numbers support to esp4.
We use the authencesn crypto algorithm to handle esp with separate
encryption/authentication algorithms.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
To support IPsec extended sequence numbers, we split the
output sequence numbers of xfrm_skb_cb in low and high order 32 bits
and we add the high order 32 bits to the input sequence numbers.
All users are updated accordingly.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
On current net-next-2.6, when Linux receives ICMP Type: 3, Code: 4
(Destination unreachable (Fragmentation needed)),
icmp_unreach
-> ip_rt_frag_needed
(peer->pmtu_expires is set here)
-> tcp_v4_err
-> do_pmtu_discovery
-> ip_rt_update_pmtu
(peer->pmtu_expires is already set,
so check_peer_pmtu is skipped.)
-> check_peer_pmtu
check_peer_pmtu is skipped and MTU is not updated.
To fix this, let check_peer_pmtu execute unconditionally.
And some minor fixes
1) Avoid potential peer->pmtu_expires set to be zero.
2) In check_peer_pmtu, argument of time_before is reversed.
3) check_peer_pmtu expects peer->pmtu_orig is initialized as zero,
but not initialized.
Signed-off-by: Hiroaki SHIMODA <shimoda.hiroaki@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To start doing these conversions, we need to add some temporary
flow4_* macros which will eventually go away when all the protocol
code paths are changed to work on AF specific flowi objects.
Signed-off-by: David S. Miller <davem@davemloft.net>
Now we have struct flowi4, flowi6, and flowidn for each address
family. And struct flowi is just a union of them all.
It might have been troublesome to convert flow_cache_uli_match() but
as it turns out this function is completely unused and therefore can
be simply removed.
Signed-off-by: David S. Miller <davem@davemloft.net>
Create two sets of port member accessors, one set prefixed by fl4_*
and the other prefixed by fl6_*
This will let us to create AF optimal flow instances.
It will work because every context in which we access the ports,
we have to be fully aware of which AF the flowi is anyways.
Signed-off-by: David S. Miller <davem@davemloft.net>
I intend to turn struct flowi into a union of AF specific flowi
structs. There will be a common structure that each variant includes
first, much like struct sock_common.
This is the first step to move in that direction.
Signed-off-by: David S. Miller <davem@davemloft.net>
The idea here is this minimizes the number of places one has to edit
in order to make changes to how flows are defined and used.
Signed-off-by: David S. Miller <davem@davemloft.net>
All callers are under rcu_read_lock() protection already.
Rename to ip_check_mc_rcu() to make it even more clear.
Signed-off-by: David S. Miller <davem@davemloft.net>
Like in commit 44713b67db
("ipv4: Optimize flow initialization in output route lookup."
we can optimize the on-stack flow setup to only initialize
the members which are actually used.
Otherwise we bzero the entire structure, then initialize
explicitly the first half of it.
Signed-off-by: David S. Miller <davem@davemloft.net>
Like in commit 44713b67db
("ipv4: Optimize flow initialization in output route lookup."
we can optimize the on-stack flow setup to only initialize
the members which are actually used.
Otherwise we bzero the entire structure, then initialize
explicitly the first half of it.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since a8f80e8ff9 any process with
CAP_NET_ADMIN may load any module from /lib/modules/. This doesn't mean
that CAP_NET_ADMIN is a superset of CAP_SYS_MODULE as modules are
limited to /lib/modules/**. However, CAP_NET_ADMIN capability shouldn't
allow anybody load any module not related to networking.
This patch restricts an ability of autoloading modules to netdev modules
with explicit aliases. This fixes CVE-2011-1019.
Arnd Bergmann suggested to leave untouched the old pre-v2.6.32 behavior
of loading netdev modules by name (without any prefix) for processes
with CAP_SYS_MODULE to maintain the compatibility with network scripts
that use autoloading netdev modules by aliases like "eth0", "wlan0".
Currently there are only three users of the feature in the upstream
kernel: ipip, ip_gre and sit.
root@albatros:~# capsh --drop=$(seq -s, 0 11),$(seq -s, 13 34) --
root@albatros:~# grep Cap /proc/$$/status
CapInh: 0000000000000000
CapPrm: fffffff800001000
CapEff: fffffff800001000
CapBnd: fffffff800001000
root@albatros:~# modprobe xfs
FATAL: Error inserting xfs
(/lib/modules/2.6.38-rc6-00001-g2bf4ca3/kernel/fs/xfs/xfs.ko): Operation not permitted
root@albatros:~# lsmod | grep xfs
root@albatros:~# ifconfig xfs
xfs: error fetching interface information: Device not found
root@albatros:~# lsmod | grep xfs
root@albatros:~# lsmod | grep sit
root@albatros:~# ifconfig sit
sit: error fetching interface information: Device not found
root@albatros:~# lsmod | grep sit
root@albatros:~# ifconfig sit0
sit0 Link encap:IPv6-in-IPv4
NOARP MTU:1480 Metric:1
root@albatros:~# lsmod | grep sit
sit 10457 0
tunnel4 2957 1 sit
For CAP_SYS_MODULE module loading is still relaxed:
root@albatros:~# grep Cap /proc/$$/status
CapInh: 0000000000000000
CapPrm: ffffffffffffffff
CapEff: ffffffffffffffff
CapBnd: ffffffffffffffff
root@albatros:~# ifconfig xfs
xfs: error fetching interface information: Device not found
root@albatros:~# lsmod | grep xfs
xfs 745319 0
Reference: https://lkml.org/lkml/2011/2/24/203
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: Michael Tokarev <mjt@tls.msk.ru>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: Kees Cook <kees.cook@canonical.com>
Signed-off-by: James Morris <jmorris@namei.org>
In contrast to SIOCOUTQ which returns the amount of data sent
but not yet acknowledged plus data not yet sent this patch only
returns the data not sent.
For various methods of live streaming bitrate control it may
be helpful to know how much data are in the tcp outqueue are
not sent yet.
Signed-off-by: Mario Schuknecht <m.schuknecht@dresearch.de>
Signed-off-by: Steffen Sledz <sledz@dresearch.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Create a common helper for this operation, since we do
it identically in three spots.
Suggested by Eric Dumazet.
Signed-off-by: David S. Miller <davem@davemloft.net>
In usual cases ifa_address == ifa_local, but in the case where
SIOCSIFDSTADDR sets the destination address on a point-to-point
link, ifa_address gets set to that destination address.
Therefore we should use ifa_local when we want the local interface
address.
There were two cases where the selection was done incorrectly:
1) When devinet_ioctl() does matching, it checks ifa_address even
though gifconf correct reported ifa_local to the user
2) IN_DEV_ARP_NOTIFY handling sends a gratuitous ARP using
ifa_address instead of ifa_local.
Reported-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
If modifications on other cpus are ok, then modifications to
the tree during lookup done by the local cpu are ok too.
Signed-off-by: David S. Miller <davem@davemloft.net>
We have to use cfg->fc_scope not the final nh_scope value.
Reported-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: David S. Miller <davem@davemloft.net>
When doing output route lookups, we have to select the source address
if the user has not specified an explicit one.
First, if the route has an explicit preferred source address
specified, then we use that.
Otherwise we search the route's outgoing interface for a suitable
address.
This search can be precomputed and cached at route insertion time.
The only missing part is that we have to refresh this precomputed
value any time addresses are added or removed from the interface, and
this is accomplished by fib_update_nh_saddrs().
Signed-off-by: David S. Miller <davem@davemloft.net>
fib_semantic_match() requires that if the type doesn't signal an
automatic error, it must be of type RTN_UNICAST, RTN_LOCAL,
RTN_BROADCAST, RTN_ANYCAST, or RTN_MULTICAST.
Checking this every route lookup is pointless work.
Instead validate it during route insertion, via fib_create_info().
Also, there was nothing making sure the type value was less than
RTN_MAX, so add that missing check while we're here.
Signed-off-by: David S. Miller <davem@davemloft.net>
The only necessary parts are the src/dst addresses, the
interface indexes, the TOS, and the mark.
The rest is unnecessary bloat, which amounts to nearly
50 bytes on 64-bit.
Signed-off-by: David S. Miller <davem@davemloft.net>
rt->rt_iif is only ever inspected on input routes, for example DCCP
uses this to populate a route lookup flow key when generating replies
to another packet.
Therefore, setting it to anything other than zero on output routes
makes no sense.
Signed-off-by: David S. Miller <davem@davemloft.net>
We burn a lot of useless cycles, cpu store buffer traffic, and
memory operations memset()'ing the on-stack flow used to perform
output route lookups in __ip_route_output_key().
Only the first half of the flow object members even matter for
output route lookups in this context, specifically:
FIB rules matching cares about:
dst, src, tos, iif, oif, mark
FIB trie lookup cares about:
dst
FIB semantic match cares about:
tos, scope, oif
Therefore only initialize these specific members and elide the
memset entirely.
On Niagara2 this kills about ~300 cycles from the output route
lookup path.
Likely, we can take things further, since all callers of output
route lookups essentially throw away the on-stack flow they use.
So they don't care if we use it as a scratch-pad to compute the
final flow key.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
David noticed :
------------------
Eric, I was profiling the non-routing-cache case and something that
stuck out is the case of calling inet_getpeer() with create==0.
If an entry is not found, we have to redo the lookup under a spinlock
to make certain that a concurrent writer rebalancing the tree does
not "hide" an existing entry from us.
This makes the case of a create==0 lookup for a not-present entry
really expensive. It is on the order of 600 cpu cycles on my
Niagara2.
I added a hack to not do the relookup under the lock when create==0
and it now costs less than 300 cycles.
This is now a pretty common operation with the way we handle COW'd
metrics, so I think it's definitely worth optimizing.
-----------------
One solution is to use a seqlock instead of a spinlock to protect struct
inet_peer_base.
After a failed avl tree lookup, we can easily detect if a writer did
some changes during our lookup. Taking the lock and redo the lookup is
only necessary in this case.
Note: Add one private rcu_deref_locked() macro to place in one spot the
access to spinlock included in seqlock.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As reported by Eric:
[11483.697233] IP: [<c12b0638>] dst_release+0x18/0x60
...
[11483.697741] Call Trace:
[11483.697764] [<c12fc9d2>] udp_sendmsg+0x282/0x6e0
[11483.697790] [<c12a1c01>] ? memcpy_toiovec+0x51/0x70
[11483.697818] [<c12dbd90>] ? ip_generic_getfrag+0x0/0xb0
The pointer passed to dst_release() is -EINVAL, that's because
we leave an error pointer in the local variable "rt" by accident.
NULL it out to fix the bug.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The patch to replace inet->cork with cork left out two spots in
__ip_append_data that can result in bogus packet construction.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
The route lookup code in icmp_send() is slightly tricky as a result of
having to handle all of the requirements of RFC 4301 host relookups.
Pull the route resolution into a seperate function, so that the error
handling and route reference counting is hopefully easier to see and
contained wholly within this new routine.
Signed-off-by: David S. Miller <davem@davemloft.net>
The UDP transmit path has been running under the socket lock
for a long time because of the corking feature. This means that
transmitting to the same socket in multiple threads does not
scale at all.
However, as most users don't actually use corking, the locking
can be removed in the common case.
This patch creates a lockless fast path where corking is not used.
Please note that this does create a slight inaccuracy in the
enforcement of socket send buffer limits. In particular, we
may exceed the socket limit by up to (number of CPUs) * (packet
size) because of the way the limit is computed.
As the primary purpose of socket buffers is to indicate congestion,
this should not be a great problem for now.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch converts UDP to use the new ip_finish_skb API. This
would then allows us to more easily use ip_make_skb which allows
UDP to run without a socket lock.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the helper ip_make_skb which is like ip_append_data
and ip_push_pending_frames all rolled into one, except that it does
not send the skb produced. The sending part is carried out by
ip_send_skb, which the transport protocol can call after it has
tweaked the skb.
It is meant to be called in cases where corking is not used should
have a one-to-one correspondence to sendmsg.
This patch also adds the helper ip_finish_skb which is meant to
be replace ip_push_pending_frames when corking is required.
Previously the protocol stack would peek at the socket write
queue and add its header to the first packet. With ip_finish_skb,
the protocol stack can directly operate on the final skb instead,
just like the non-corking case with ip_make_skb.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to allow simultaneous calls to ip_append_data on the same
socket, it must not modify any shared state in sk or inet (other
than those that are designed to allow that such as atomic counters).
This patch abstracts out write references to sk and inet_sk in
ip_append_data and its friends so that we may use the underlying
code in parallel.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UFO doesn't really use the sk_sndmsg_* parameters so touching
them is pointless. It can't use them anyway since the whole
point of UFO is to use the original pages without copying.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_route_newports() is the only place in the entire kernel that
cares about the port members in the routing cache entry's lookup
flow key.
Therefore the only reason we store an entire flow inside of the
struct rtentry is for this one special case.
Rewrite ip_route_newports() such that:
1) The caller passes in the original port values, so we don't need
to use the rth->fl.fl_ip_{s,d}port values to remember them.
2) The lookup flow is constructed by hand instead of being copied
from the routing cache entry's flow.
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug that undo_retrans is incorrectly decremented when undo_marker is
not set or undo_retrans is already 0. This happens when sender receives
more DSACK ACKs than packets retransmitted during the current
undo phase. This may also happen when sender receives DSACK after
the undo operation is completed or cancelled.
Fix another bug that undo_retrans is incorrectly incremented when
sender retransmits an skb and tcp_skb_pcount(skb) > 1 (TSO). This case
is rare but not impossible.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now, TCP_CHECK_TIMER is not used for debuging, it does nothing.
And, it has been there for several years, maybe 6 years.
Remove it to keep code clearer.
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric W. Biederman reported a lockdep splat in inet_twsk_deschedule()
This is caused by inet_twsk_purge(), run from process context,
and commit 575f4cd5a5 (net: Use rcu lookups in inet_twsk_purge.)
removed the BH disabling that was necessary.
Add the BH disabling but fine grained, right before calling
inet_twsk_deschedule(), instead of whole function.
With help from Linus Torvalds and Eric W. Biederman
Reported-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Daniel Lezcano <daniel.lezcano@free.fr>
CC: Pavel Emelyanov <xemul@openvz.org>
CC: Arnaldo Carvalho de Melo <acme@redhat.com>
CC: stable <stable@kernel.org> (# 2.6.33+)
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0dbaee3b37 (net: Abstract default ADVMSS behind an
accessor.) introduced a possible crash in tcp_connect_init(), when
dst->default_advmss() is called from dst_metric_advmss()
Reported-by: George Spelvin <linux@horizon.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only troublesome bit here is __mkroute_output which wants
to override res->fi and res->type, compute those in local
variables instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
GCC emits all kinds of crazy zero extensions when we go from signed
int, to unsigned short, etc. etc.
This transformation has to be legal because:
1) In tkey_extract_bits() in mask_pfx(), the values are used to
perform shifts, on which negative values are undefined by C.
2) In fib_table_lookup() we perform comparisons with unsigned
values, constants, and additions. None of which should
encounter negative values.
Signed-off-by: David S. Miller <davem@davemloft.net>
This allows avoiding multiple writes to the initial __refcnt.
The most simplest cases of wanting an initial reference of "1"
in ipv4 and ipv6 have been converted, the rest have been left
along and kept at the existing "0".
Signed-off-by: David S. Miller <davem@davemloft.net>
This also allows us to combine all the dst->flags settings and avoid
read/modify/write sequences to this struct member.
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a lot of redundancy and unnecessary stack frames
in the output route creation path.
1) Make __mkroute_output() return error pointers.
2) Eliminate ip_mkroute_output() entirely, made possible by #1.
3) Call __mkroute_output() directly and handling the returning error
pointers in ip_route_output_slow().
Signed-off-by: David S. Miller <davem@davemloft.net>
Note that we do not generate the redirect netevent any longer,
because we don't create a new cached route.
Instead, once the new neighbour is bound to the cached route,
we emit a neigh update event instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
The general idea is that if we learn new PMTU information, we
bump the peer genid.
This triggers the dst_ops->check() code to validate and if
necessary propagate the new PMTU value into the metrics.
Learned PMTU information self-expires.
This means that it is not necessary to kill a cached route
entry just because the PMTU information is too old.
As a consequence:
1) When the path appears unreachable (dst_ops->link_failure
or dst_ops->negative_advice) we unwind the PMTU state if
it is out of date, instead of killing the cached route.
A redirected route will still be invalidated in these
situations.
2) rt_check_expire(), rt_worker_func(), et al. are no longer
necessary at all.
Signed-off-by: David S. Miller <davem@davemloft.net>
NETDEV_NOTIFY_PEER is an explicit request by the driver to send a link
notification while NETDEV_UP/NETDEV_CHANGEADDR generate link
notifications as a sort of side effect.
In the later cases the sysctl option is present because link
notification events can have undesired effects e.g. if the link is
flapping. I don't think this applies in the case of an explicit
request from a driver.
This patch makes NETDEV_NOTIFY_PEER unconditional, if preferred we
could add a new sysctl for this case which defaults to on.
This change causes Xen post-migration ARP notifications (which cause
switches to relearn their MAC tables etc) to be sent by default.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 0c838ff1ad (ipv4: Consolidate all default route selection
implementations.) forgot to remove one rcu_read_unlock() from
fib_select_default().
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 5811662b15 ("net: use the macros
defined for the members of flowi") accidentally removed the setting of
IPPROTO_GRE from the struct flowi in ipgre_tunnel_xmit. This patch
restores it.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If we didn't have a routing cache, we would not be able to properly
propagate certain kinds of dynamic path attributes, for example
PMTU information and redirects.
The reason is that if we didn't have a routing cache, then there would
be no way to lookup all of the active cached routes hanging off of
sockets, tunnels, IPSEC bundles, etc.
Consider the case where we created a cached route, but no inetpeer
entry existed and also we were not asked to pre-COW the route metrics
and therefore did not force the creation a new inetpeer entry.
If we later get a PMTU message, or a redirect, and store this
information in a new inetpeer entry, there is no way to teach that
cached route about the newly existing inetpeer entry.
The facilities implemented here handle this problem.
First we create a generation ID. When we create a cached route of any
kind, we remember the generation ID at the time of attachment. Any
time we force-create an inetpeer entry in response to new path
information, we bump that generation ID.
The dst_ops->check() callback is where the knowledge of this event
is propagated. If the global generation ID does not equal the one
stored in the cached route, and the cached route has not attached
to an inetpeer yet, we look it up and attach if one is found. Now
that we've updated the cached route's information, we update the
route's generation ID too.
This clears the way for implementing PMTU and redirects directly in
the inetpeer cache. There is absolutely no need to consult cached
route information in order to maintain this information.
At this point nothing bumps the inetpeer genids, that comes in the
later changes which handle PMTUs and redirects using inetpeers.
Signed-off-by: David S. Miller <davem@davemloft.net>
Validity of the cached PMTU information is indicated by it's
expiration value being non-zero, just as per dst->expires.
The scheme we will use is that we will remember the pre-ICMP value
held in the metrics or route entry, and then at expiration time
we will restore that value.
In this way PMTU expiration does not kill off the cached route as is
done currently.
Redirect information is permanent, or at least until another redirect
is received.
Signed-off-by: David S. Miller <davem@davemloft.net>
Future changes will add caching information, and some of
these new elements will be addresses.
Since the family is implicit via the ->daddr.family member,
replicating the family in ever address we store is entirely
redundant.
Signed-off-by: David S. Miller <davem@davemloft.net>
The Linux IPv4 AH stack aligns the AH header on a 64 bit boundary
(like in IPv6). This is not RFC compliant (see RFC4302, Section
3.3.3.2.1), it should be aligned on 32 bits.
For most of the authentication algorithms, the ICV size is 96 bits.
The AH header alignment on 32 or 64 bits gives the same results.
However for SHA-256-128 for instance, the wrong 64 bit alignment results
in adding useless padding in IPv4 AH, which is forbidden by the RFC.
To avoid breaking backward compatibility, we use a new flag
(XFRM_STATE_ALIGN4) do change original behavior.
Initial patch from Dang Hongwu <hongwu.dang@6wind.com> and
Christophe Gouault <christophe.gouault@6wind.com>.
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like metrics, the ICMP rate limiting bits are cached state about
a destination. So move it into the inet_peer entries.
If an inet_peer cannot be bound (the reason is memory allocation
failure or similar), the policy is to allow.
Signed-off-by: David S. Miller <davem@davemloft.net>
Always lookup to see if we have an existing inetpeer entry for
a route. Let FLOWI_FLAG_PRECOW_METRICS merely influence the
"create" argument to rt_bind_peer().
Also, call rt_bind_peer() unconditionally since it is not
possible for rt->peer to be non-NULL at this point.
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 709b46e8d9 ("net: Add compat
ioctl support for the ipv4 multicast ioctl SIOCGETSGCNT") added the
correct plumbing to handle SIOCGETSGCNT properly.
However, whilst definiting a proper "struct compat_sioc_sg_req" it
isn't actually used in ipmr_compat_ioctl().
Correct this oversight.
Signed-off-by: David S. Miller <davem@davemloft.net>
If we end up including include/linux/node.h (either explicitly
or implicitly) that header has a definition of "structt node"
too.
So rename the one we use in fib_trie to "rt_trie_node" to avoid
the conflict.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
To avoid confusion with the recently deleted fib_hash.c
code, use "fib_info_hash_*" instead of plain "fib_hash_*".
Signed-off-by: David S. Miller <davem@davemloft.net>
The time has finally come to remove the hash based routing table
implementation in ipv4.
FIB Trie is mature, well tested, and I've done an audit of it's code
to confirm that it implements insert, delete, and lookup with the same
identical semantics as fib_hash did.
If there are any semantic differences found in fib_trie, we should
simply fix them.
I've placed the trie statistic config option under advanced router
configuration.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
In 135367b "netfilter: xtables: change xt_target.checkentry return type",
the type returned by checkentry was changed from boolean to int, but the
return values where not adjusted.
arptables: Input/output error
This broke arptables with the mangle target since it returns true
under success, which is interpreted by xtables as >0, thus
returning EIO.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Both fib_trie and fib_hash have a local implementation of
fib_table_select_default(). This is completely unnecessary
code duplication.
Since we now remember the fib_table and the head of the fib
alias list of the default route, we can implement one single
generic version of this routine.
Looking at the fib_hash implementation you may get the impression
that it's possible for there to be multiple top-level routes in
the table for the default route. The truth is, it isn't, the
insert code will only allow one entry to exist in the zero
prefix hash table, because all keys evaluate to zero and all
keys in a hash table must be unique.
Signed-off-by: David S. Miller <davem@davemloft.net>
This will be used later to implement fib_select_default() in a
completely generic manner, instead of the current situation where the
default route is re-looked up in the TRIE/HASH table and then the
available aliases are analyzed.
Signed-off-by: David S. Miller <davem@davemloft.net>
When an IPSEC SA is still being set up, __xfrm_lookup() will return
-EREMOTE and so ip_route_output_flow() will return a blackhole route.
This can happen in a sndmsg call, and after d33e455337 ("net: Abstract
default MTU metric calculation behind an accessor.") this leads to a
crash in ip_append_data() because the blackhole dst_ops have no
default_mtu() method and so dst_mtu() calls a NULL pointer.
Fix this by adding default_mtu() methods (that simply return 0, matching
the old behavior) to the blackhole dst_ops.
The IPv4 part of this patch fixes a crash that I saw when using an IPSEC
VPN; the IPv6 part is untested because I don't have an IPv6 VPN, but it
looks to be needed as well.
Signed-off-by: Roland Dreier <roland@purestorage.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
SIOCGETSGCNT is not a unique ioctl value as it it maps tio SIOCPROTOPRIVATE +1,
which unfortunately means the existing infrastructure for compat networking
ioctls is insufficient. A trivial compact ioctl implementation would conflict
with:
SIOCAX25ADDUID
SIOCAIPXPRISLT
SIOCGETSGCNT_IN6
SIOCGETSGCNT
SIOCRSSCAUSE
SIOCX25SSUBSCRIP
SIOCX25SDTEFACILITIES
To make this work I have updated the compat_ioctl decode path to mirror the
the normal ioctl decode path. I have added an ipv4 inet_compat_ioctl function
so that I can have ipv4 specific compat ioctls. I have added a compat_ioctl
function into struct proto so I can break out ioctls by which kind of ip socket
I am using. I have added a compat_raw_ioctl function because SIOCGETSGCNT only
works on raw sockets. I have added a ipmr_compat_ioctl that mirrors the normal
ipmr_ioctl.
This was necessary because unfortunately the struct layout for the SIOCGETSGCNT
has unsigned longs in it so changes between 32bit and 64bit kernels.
This change was sufficient to run a 32bit ip multicast routing daemon on a
64bit kernel.
Reported-by: Bill Fenner <fenner@aristanetworks.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The fib metric memory in this case is static in the kernel image,
so we don't need to reference count it since it's never going
to go away on us.
Signed-off-by: David S. Miller <davem@davemloft.net>
If there are no explicit metrics attached to a route, hook
fi->fib_info up to dst_default_metrics.
Signed-off-by: David S. Miller <davem@davemloft.net>
This is the initial gateway towards super-sharing metrics
if they are all set to zero for a route.
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP is going to record metrics for the connection,
so pre-COW the route metrics at route cache entry
creation time.
This avoids several atomic operations that have to
occur if we COW the metrics after the entry reaches
global visibility.
Signed-off-by: David S. Miller <davem@davemloft.net>
Please note that the IPSEC dst entry metrics keep using
the generic metrics COW'ing mechanism using kmalloc/kfree.
This gives the IPSEC routes an opportunity to use metrics
which are unique to their encapsulated paths.
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the RTAX_LOCKED metric to INETPEER_METRICS_NEW (basically,
all ones) on fresh inetpeer entries.
This way code can determine if default metrics have been loaded
in from a routing table entry already.
Signed-off-by: David S. Miller <davem@davemloft.net>
Routing metrics are now copy-on-write.
Initially a route entry points it's metrics at a read-only location.
If a routing table entry exists, it will point there. Else it will
point at the all zero metric place-holder called 'dst_default_metrics'.
The writeability state of the metrics is stored in the low bits of the
metrics pointer, we have two bits left to spare if we want to store
more states.
For the initial implementation, COW is implemented simply via kmalloc.
However future enhancements will change this to place the writable
metrics somewhere else, in order to increase sharing. Very likely
this "somewhere else" will be the inetpeer cache.
Note also that this means that metrics updates may transiently fail
if we cannot COW the metrics successfully.
But even by itself, this patch should decrease memory usage and
increase cache locality especially for routing workloads. In those
cases the read-only metric copies stay in place and never get written
to.
TCP workloads where metrics get updated, and those rare cases where
PMTU triggers occur, will take a very slight performance hit. But
that hit will be alleviated when the long-term writable metrics
move to a more sharable location.
Since the metrics storage went from a u32 array of RTAX_MAX entries to
what is essentially a pointer, some retooling of the dst_entry layout
was necessary.
Most importantly, we need to preserve the alignment of the reference
count so that it doesn't share cache lines with the read-mostly state,
as per Eric Dumazet's alignment assertion checks.
The only non-trivial bit here is the move of the 'flags' member into
the writeable cacheline. This is OK since we are always accessing the
flags around the same moment when we made a modification to the
reference count.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes a bug that causes TCP RST packets to be generated
on otherwise correctly behaved applications, e.g., no unread data
on close,..., etc. To trigger the bug, at least two conditions must
be met:
1. The FIN flag is set on the last data packet, i.e., it's not on a
separate, FIN only packet.
2. The size of the last data chunk on the receive side matches
exactly with the size of buffer posted by the receiver, and the
receiver closes the socket without any further read attempt.
This bug was first noticed on our netperf based testbed for our IW10
proposal to IETF where a large number of RST packets were observed.
netperf's read side code meets the condition 2 above 100%.
Before the fix, tcp_data_queue() will queue the last skb that meets
condition 1 to sk_receive_queue even though it has fully copied out
(skb_copy_datagram_iovec()) the data. Then if condition 2 is also met,
tcp_recvmsg() often returns all the copied out data successfully
without actually consuming the skb, due to a check
"if ((chunk = len - tp->ucopy.len) != 0) {"
and
"len -= chunk;"
after tcp_prequeue_process() that causes "len" to become 0 and an
early exit from the big while loop.
I don't see any reason not to free the skb whose data have been fully
consumed in tcp_data_queue(), regardless of the FIN flag. We won't
get there if MSG_PEEK is on. Am I missing some arcane cases related
to urgent data?
Signed-off-by: H.K. Jerry Chu <hkchu@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Quoting Ben Hutchings: we presumably won't be defining features that
can only be enabled on 64-bit architectures.
Occurences found by `grep -r` on net/, drivers/net, include/
[ Move features and vlan_features next to each other in
struct netdev, as per Eric Dumazet's suggestion -DaveM ]
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit a8b690f98b (tcp: Fix slowness in read /proc/net/tcp)
introduced a bug in handling of SYN_RECV sockets.
st->offset represents number of sockets found since beginning of
listening_hash[st->bucket].
We should not reset st->offset when iterating through
syn_table[st->sbucket], or else if more than ~25 sockets (if
PAGE_SIZE=4096) are in SYN_RECV state, we exit from listening_get_next()
with a too small st->offset
Next time we enter tcp_seek_last_pos(), we are not able to seek past
already found sockets.
Reported-by: PK <runningdoglackey@yahoo.com>
CC: Tom Herbert <therbert@google.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Family was hard-coded to AF_INET but should be daddr->family.
This fixes crashes when unlinking ipv6 peer entries, since the
unlink code was looking up the base pointer properly.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 941666c2e3 "net: RCU conversion of dev_getbyhwaddr() and
arp_ioctl()" introduced a regression, reported by Jamie Heilman.
"arp -Ds 192.168.2.41 eth0 pub" triggered the ASSERT_RTNL() assert
in pneigh_lookup()
Removing RTNL requirement from arp_ioctl() was a mistake, just revert
that part.
Reported-by: Jamie Heilman <jamie@audible.transient.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If SNAT isn't done, the wrong info maybe got by the other cts.
As the filter table is after DNAT table, the packets dropped in filter
table also bother bysource hash table.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
ret != NF_QUEUE only works in the "--queue-num 0" case; for
queues > 0 the test should be '(ret & NF_VERDICT_MASK) != NF_QUEUE'.
However, NF_QUEUE no longer DROPs the skb unconditionally if queueing
fails (due to NF_VERDICT_FLAG_QUEUE_BYPASS verdict flag), so the
re-route test should also be performed if this flag is set in the
verdict.
The full test would then look something like
&& ((ret & NF_VERDICT_MASK) == NF_QUEUE && (ret & NF_VERDICT_FLAG_QUEUE_BYPASS))
This is rather ugly, so just remove the NF_QUEUE test altogether.
The only effect is that we might perform an unnecessary route lookup
in the NF_QUEUE case.
ip6table_mangle did not have such a check.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Patrick McHardy <kaber@trash.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (41 commits)
sctp: user perfect name for Delayed SACK Timer option
net: fix can_checksum_protocol() arguments swap
Revert "netlink: test for all flags of the NLM_F_DUMP composite"
gianfar: Fix misleading indentation in startup_gfar()
net/irda/sh_irda: return to RX mode when TX error
net offloading: Do not mask out NETIF_F_HW_VLAN_TX for vlan.
USB CDC NCM: tx_fixup() race condition fix
ns83820: Avoid bad pointer deref in ns83820_init_one().
ipv6: Silence privacy extensions initialization
bnx2x: Update bnx2x version to 1.62.00-4
bnx2x: Fix AER setting for BCM57712
bnx2x: Fix BCM84823 LED behavior
bnx2x: Mark full duplex on some external PHYs
bnx2x: Fix BCM8073/BCM8727 microcode loading
bnx2x: LED fix for BCM8727 over BCM57712
bnx2x: Common init will be executed only once after POR
bnx2x: Swap BCM8073 PHY polarity if required
iwlwifi: fix valid chain reading from EEPROM
ath5k: fix locking in tx_complete_poll_work
ath9k_hw: do PA offset calibration only on longcal interval
...
Adding support for SNMP broadcast connection tracking. The SNMP
broadcast requests are now paired with the SNMP responses.
Thus allowing using SNMP broadcasts with firewall enabled.
Please refer to the following conversation:
http://marc.info/?l=netfilter-devel&m=125992205006600&w=2
Patrick McHardy wrote:
> > The best solution would be to add generic broadcast tracking, the
> > use of expectations for this is a bit of abuse.
> > The second best choice I guess would be to move the help() function
> > to a shared module and generalize it so it can be used for both.
This patch implements the "second best choice".
Since the netbios-ns conntrack module uses the same helper
functionality as the snmp, only one helper function is added
for both snmp and netbios-ns modules into the new object -
nf_conntrack_broadcast.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
When a packet is meant to be handled by another node of the cluster,
silently drop it instead of flooding kernel log.
Note : INVALID packets are also dropped without notice.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
My previous patch (netfilter: nf_nat: don't use atomic bit operation)
made a mistake when converting atomic_set to a normal bit 'or'.
IPS_*_BIT should be replaced with IPS_*.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Cc: Tim Gardner <tim.gardner@canonical.com>
Cc: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Use is_vmalloc_addr() in nf_ct_free_hashtable() and get rid of
the vmalloc flags to indicate that a hash table has been allocated
using vmalloc().
Signed-off-by: Patrick McHardy <kaber@trash.net>
Fix dependencies of netfilter realm match: it depends on NET_CLS_ROUTE,
which itself depends on NET_SCHED; this dependency is missing from netfilter.
Since matching on realms is also useful without having NET_SCHED enabled and
the option really only controls whether the tclassid member is included in
route and dst entries, rename the config option to IP_ROUTE_CLASSID and move
it outside of traffic scheduling context to get rid of the NET_SCHED dependeny.
Reported-by: Vladis Kletnieks <Valdis.Kletnieks@vt.edu>
Signed-off-by: Patrick McHardy <kaber@trash.net>
One iptables invocation with 135000 rules takes 35 seconds of cpu time
on a recent server, using a 32bit distro and a 64bit kernel.
We eventually trigger NMI/RCU watchdog.
INFO: rcu_sched_state detected stall on CPU 3 (t=6000 jiffies)
COMPAT mode has quadratic behavior and consume 16 bytes of memory per
rule.
Switch the xt_compat algos to use an array instead of list, and use a
binary search to locate an offset in the sorted array.
This halves memory need (8 bytes per rule), and removes quadratic
behavior [ O(N*N) -> O(N*log2(N)) ]
Time of iptables goes from 35 s to 150 ms.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
skb_cow_data() may allocate a new data buffer, so pointers on
skb should be set after this function.
Bug was introduced by commit dff3bb06 ("ah4: convert to ahash")
and 8631e9bd ("ah6: convert to ahash").
Signed-off-by: Wang Xuefu <xuefu.wang@6wind.com>
Acked-by: Krzysztof Witek <krzysztof.witek@6wind.com>
Signed-off-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
inet_csk_bind_conflict() logic currently disallows a bind() if
it finds a friend socket (a socket bound on same address/port)
satisfying a set of conditions :
1) Current (to be bound) socket doesnt have sk_reuse set
OR
2) other socket doesnt have sk_reuse set
OR
3) other socket is in LISTEN state
We should add the CLOSE state in the 3) condition, in order to avoid two
REUSEADDR sockets in CLOSE state with same local address/port, since
this can deny further operations.
Note : a prior patch tried to address the problem in a different (and
buggy) way. (commit fda48a0d7a tcp: bind() fix when many ports
are bound).
Reported-by: Gaspar Chilingarov <gasparch@gmail.com>
Reported-by: Daniel Baluta <daniel.baluta@gmail.com>
Tested-by: Daniel Baluta <daniel.baluta@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 over firewire needs to be able to remove ARP entries
from the ARP cache that belong to nodes that are removed, because
IPv4 over firewire uses ARP packets for private information
about nodes.
This information becomes invalid as soon as node drops
off the bus and when it reconnects, its only possible
to start talking to it after it responded to an ARP packet.
But ARP cache prevents such packets from being sent.
Signed-off-by: Maxim Levitsky <maximlevitsky@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using "iptables -L" with a lot of rules have a too big BH latency.
Jesper mentioned ~6 ms and worried of frame drops.
Switch to a per_cpu seqlock scheme, so that taking a snapshot of
counters doesnt need to block BH (for this cpu, but also other cpus).
This adds two increments on seqlock sequence per ipt_do_table() call,
its a reasonable cost for allowing "iptables -L" not block BH
processing.
Reported-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
CC: Patrick McHardy <kaber@trash.net>
Acked-by: Stephen Hemminger <shemminger@vyatta.com>
Acked-by: Jesper Dangaard Brouer <hawk@comx.dk>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Due to NLM_F_DUMP is composed of two bits, NLM_F_ROOT | NLM_F_MATCH,
when doing "if (x & NLM_F_DUMP)", it tests for _either_ of the bits
being set. Because NLM_F_MATCH's value overlaps with NLM_F_EXCL,
non-dump requests with NLM_F_EXCL set are mistaken as dump requests.
Substitute the condition to test for _all_ bits being set.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
Acked-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In 1ae4de0cdf, the secctx was exported
via the /proc/net/netfilter/nf_conntrack and ctnetlink interfaces
instead of the secmark.
That patch introduced the use of security_secid_to_secctx() which may
return a non-zero value on error.
In one of my setups, I have NF_CONNTRACK_SECMARK enabled but no
security modules. Thus, security_secid_to_secctx() returns a negative
value that results in the breakage of the /proc and `conntrack -L'
outputs. To fix this, we skip the inclusion of secctx if the
aforementioned function fails.
This patch also fixes the dynamic netlink message size calculation
if security_secid_to_secctx() returns an error, since its logic is
also wrong.
This problem exists in Linux kernel >= 2.6.37.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC3168 (The Addition of Explicit Congestion Notification to IP)
states :
5.3. Fragmentation
ECN-capable packets MAY have the DF (Don't Fragment) bit set.
Reassembly of a fragmented packet MUST NOT lose indications of
congestion. In other words, if any fragment of an IP packet to be
reassembled has the CE codepoint set, then one of two actions MUST be
taken:
* Set the CE codepoint on the reassembled packet. However, this
MUST NOT occur if any of the other fragments contributing to
this reassembly carries the Not-ECT codepoint.
* The packet is dropped, instead of being reassembled, for any
other reason.
This patch implements this requirement for IPv4, choosing the first
action :
If one fragment had NO-ECT codepoint
reassembled frame has NO-ECT
ElIf one fragment had CE codepoint
reassembled frame has CE
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The preferred source address is currently ignored for local routes,
which results in all local connections having a src address that is the
same as the local dst address. Fix this by respecting the preferred source
address when it is provided for local routes.
This bug can be demonstrated as follows:
# ifconfig dummy0 192.168.0.1
# ip route show table local | grep local.*dummy0
local 192.168.0.1 dev dummy0 proto kernel scope host src 192.168.0.1
# ip route change table local local 192.168.0.1 dev dummy0 \
proto kernel scope host src 127.0.0.1
# ip route show table local | grep local.*dummy0
local 192.168.0.1 dev dummy0 proto kernel scope host src 127.0.0.1
We now establish a local connection and verify the source IP
address selection:
# nc -l 192.168.0.1 3128 &
# nc 192.168.0.1 3128 &
# netstat -ant | grep 192.168.0.1:3128.*EST
tcp 0 0 192.168.0.1:3128 192.168.0.1:33228 ESTABLISHED
tcp 0 0 192.168.0.1:33228 192.168.0.1:3128 ESTABLISHED
Signed-off-by: Joel Sing <jsing@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In ip_route_output_slow(), instead of allowing a route to be created on
a not UPed device, report -ENETUNREACH immediately.
# ip tunnel add mode ipip remote 10.16.0.164 local
10.16.0.72 dev eth0
# (Note : tunl1 is down)
# ping -I tunl1 10.1.2.3
PING 10.1.2.3 (10.1.2.3) from 192.168.18.5 tunl1: 56(84) bytes of data.
(nothing)
# ./a.out tunl1
# ip tunnel del tunl1
Message from syslogd@shelby at Dec 22 10:12:08 ...
kernel: unregister_netdevice: waiting for tunl1 to become free.
Usage count = 3
After patch:
# ping -I tunl1 10.1.2.3
connect: Network is unreachable
Reported-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reviewed-by: Octavian Purdila <opurdila@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 4465b46900.
Conflicts:
net/ipv4/fib_frontend.c
As reported by Ben Greear, this causes regressions:
> Change 4465b46900 caused rules
> to stop matching the input device properly because the
> FLOWI_FLAG_MATCH_ANY_IIF is always defined in ip_dev_find().
>
> This breaks rules such as:
>
> ip rule add pref 512 lookup local
> ip rule del pref 0 lookup local
> ip link set eth2 up
> ip -4 addr add 172.16.0.102/24 broadcast 172.16.0.255 dev eth2
> ip rule add to 172.16.0.102 iif eth2 lookup local pref 10
> ip rule add iif eth2 lookup 10001 pref 20
> ip route add 172.16.0.0/24 dev eth2 table 10001
> ip route add unreachable 0/0 table 10001
>
> If you had a second interface 'eth0' that was on a different
> subnet, pinging a system on that interface would fail:
>
> [root@ct503-60 ~]# ping 192.168.100.1
> connect: Invalid argument
Reported-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 86bcebafc5 ("tcp: fix >2 iw selection") fixed a case
when congestion window initialization has been mistakenly omitted
by introducing cwnd label and putting backwards goto from the
end of the function.
This makes the code unnecessarily tricky to read and understand
on a first sight.
Shuffle the code around a little bit to make it more obvious.
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexey Vlasov found /proc/net/tcp could sometime loop and display
millions of sockets in LISTEN state.
In 2.6.29, when we converted TCP hash tables to RCU, we left two
sk_next() calls in listening_get_next().
We must instead use sk_nulls_next() to properly detect an end of chain.
Reported-by: Alexey Vlasov <renton@renton.name>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
arch/arm/mach-omap2/pm24xx.c
drivers/scsi/bfa/bfa_fcpim.c
Needed to update to apply fixes for which the old branch was too
outdated.
This patch changes the default initial receive window to 10 mss
(defined constant). The default window is limited to the maximum
of 10*1460 and 2*mss (when mss > 1460).
draft-ietf-tcpm-initcwnd-00 is a proposal to the IETF that recommends
increasing TCP's initial congestion window to 10 mss or about 15KB.
Leading up to this proposal were several large-scale live Internet
experiments with an initial congestion window of 10 mss (IW10), where
we showed that the average latency of HTTP responses improved by
approximately 10%. This was accompanied by a slight increase in
retransmission rate (0.5%), most of which is coming from applications
opening multiple simultaneous connections. To understand the extreme
worst case scenarios, and fairness issues (IW10 versus IW3), we further
conducted controlled testbed experiments. We came away finding minimal
negative impact even under low link bandwidths (dial-ups) and small
buffers. These results are extremely encouraging to adopting IW10.
However, an initial congestion window of 10 mss is useless unless a TCP
receiver advertises an initial receive window of at least 10 mss.
Fortunately, in the large-scale Internet experiments we found that most
widely used operating systems advertised large initial receive windows
of 64KB, allowing us to experiment with a wide range of initial
congestion windows. Linux systems were among the few exceptions that
advertised a small receive window of 6KB. The purpose of this patch is
to fix this shortcoming.
References:
1. A comprehensive list of all IW10 references to date.
http://code.google.com/speed/protocols/tcpm-IW10.html
2. Paper describing results from large-scale Internet experiments with IW10.
http://ccr.sigcomm.org/drupal/?q=node/621
3. Controlled testbed experiments under worst case scenarios and a
fairness study.
http://www.ietf.org/proceedings/79/slides/tcpm-0.pdf
4. Raw test data from testbed experiments (Linux senders/receivers)
with initial congestion and receive windows of both 10 mss.
http://research.csc.ncsu.edu/netsrv/?q=content/iw10
5. Internet-Draft. Increasing TCP's Initial Window.
https://datatracker.ietf.org/doc/draft-ietf-tcpm-initcwnd/
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flush the routing cache only of entries that match the
network namespace in which the purge event occurred.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Replace skb->csum_start - skb_headroom(skb) with skb_checksum_start_offset().
Note for usb/smsc95xx: skb->data - skb->head == skb_headroom(skb).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Special care is taken inside sk_port_alloc to avoid overwriting
skc_node/skc_nulls_node. We should also avoid overwriting
skc_bind_node/skc_portaddr_node.
The patch fixes the following crash:
BUG: unable to handle kernel paging request at fffffffffffffff0
IP: [<ffffffff812ec6dd>] udp4_lib_lookup2+0xad/0x370
[<ffffffff812ecc22>] __udp4_lib_lookup+0x282/0x360
[<ffffffff812ed63e>] __udp4_lib_rcv+0x31e/0x700
[<ffffffff812bba45>] ? ip_local_deliver_finish+0x65/0x190
[<ffffffff812bbbf8>] ? ip_local_deliver+0x88/0xa0
[<ffffffff812eda35>] udp_rcv+0x15/0x20
[<ffffffff812bba45>] ip_local_deliver_finish+0x65/0x190
[<ffffffff812bbbf8>] ip_local_deliver+0x88/0xa0
[<ffffffff812bb2cd>] ip_rcv_finish+0x32d/0x6f0
[<ffffffff8128c14c>] ? netif_receive_skb+0x99c/0x11c0
[<ffffffff812bb94b>] ip_rcv+0x2bb/0x350
[<ffffffff8128c14c>] netif_receive_skb+0x99c/0x11c0
Signed-off-by: Leonard Crestez <lcrestez@ixiacom.com>
Signed-off-by: Octavian Purdila <opurdila@ixiacom.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Like RTAX_ADVMSS, make the default calculation go through a dst_ops
method rather than caching the computation in the routing cache
entries.
Now dst metrics are pretty much left as-is when new entries are
created, thus optimizing metric sharing becomes a real possibility.
Signed-off-by: David S. Miller <davem@davemloft.net>
Make all RTAX_ADVMSS metric accesses go through a new helper function,
dst_metric_advmss().
Leave the actual default metric as "zero" in the real metric slot,
and compute the actual default value dynamically via a new dst_ops
AF specific callback.
For stacked IPSEC routes, we use the advmss of the path which
preserves existing behavior.
Unlike ipv4/ipv6, DecNET ties the advmss to the mtu and thus updates
advmss on pmtu updates. This inconsistency in advmss handling
results in more raw metric accesses than I wish we ended up with.
Signed-off-by: David S. Miller <davem@davemloft.net>
Always go through a new ip4_dst_hoplimit() helper, just like ipv6.
This allowed several simplifications:
1) The interim dst_metric_hoplimit() can go as it's no longer
userd.
2) The sysctl_ip_default_ttl entry no longer needs to use
ipv4_doint_and_flush, since the sysctl is not cached in
routing cache metrics any longer.
3) ipv4_doint_and_flush no longer needs to be exported and
therefore can be marked static.
When ipv4_doint_and_flush_strategy was removed some time ago,
the external declaration in ip.h was mistakenly left around
so kill that off too.
We have to move the sysctl_ip_default_ttl declaration into
ipv4's route cache definition header net/route.h, because
currently net/ip.h (where the declaration lives now) has
a back dependency on net/route.h
Signed-off-by: David S. Miller <davem@davemloft.net>
Add TFC padding to all packets smaller than the boundary configured
on the xfrm state. If the boundary is larger than the PMTU, limit
padding to the PMTU.
Signed-off-by: Martin Willi <martin@strongswan.org>
Acked-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Followup of commit b178bb3dfc (net: reorder struct sock fields)
Optimize INET input path a bit further, by :
1) moving sk_refcnt close to sk_lock.
This reduces number of dirtied cache lines by one on 64bit arches (and
64 bytes cache line size).
2) moving inet_daddr & inet_rcv_saddr at the beginning of sk
(same cache line than hash / family / bound_dev_if / nulls_node)
This reduces number of accessed cache lines in lookups by one, and dont
increase size of inet and timewait socks.
inet and tw sockets now share same place-holder for these fields.
Before patch :
offsetof(struct sock, sk_refcnt) = 0x10
offsetof(struct sock, sk_lock) = 0x40
offsetof(struct sock, sk_receive_queue) = 0x60
offsetof(struct inet_sock, inet_daddr) = 0x270
offsetof(struct inet_sock, inet_rcv_saddr) = 0x274
After patch :
offsetof(struct sock, sk_refcnt) = 0x44
offsetof(struct sock, sk_lock) = 0x48
offsetof(struct sock, sk_receive_queue) = 0x68
offsetof(struct inet_sock, inet_daddr) = 0x0
offsetof(struct inet_sock, inet_rcv_saddr) = 0x4
compute_score() (udp or tcp) now use a single cache line per ignored
item, instead of two.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use helper functions to hide all direct accesses, especially writes,
to dst_entry metrics values.
This will allow us to:
1) More easily change how the metrics are stored.
2) Implement COW for metrics.
In particular this will help us put metrics into the inetpeer
cache if that is what we end up doing. We can make the _metrics
member a pointer instead of an array, initially have it point
at the read-only metrics in the FIB, and then on the first set
grab an inetpeer entry and point the _metrics member there.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Make sure sysctl_tcp_cookie_size is read once in
tcp_cookie_size_check(), or we might return an illegal value to caller
if sysctl_tcp_cookie_size is changed by another cpu.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: William Allen Simpson <william.allen.simpson@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
sysctl_tcp_tso_win_divisor might be set to zero while one cpu runs in
tcp_tso_should_defer(). Make sure we dont allow a divide by zero by
reading sysctl_tcp_tso_win_divisor exactly once.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than printing the message to the log, use a mib counter to keep
track of the count of occurences of time wait bucket overflow. Reduces
spam in logs.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Le dimanche 05 décembre 2010 à 09:19 +0100, Eric Dumazet a écrit :
> Hmm..
>
> If somebody can explain why RTNL is held in arp_ioctl() (and therefore
> in arp_req_delete()), we might first remove RTNL use in arp_ioctl() so
> that your patch can be applied.
>
> Right now it is not good, because RTNL wont be necessarly held when you
> are going to call arp_invalidate() ?
While doing this analysis, I found a refcount bug in llc, I'll send a
patch for net-2.6
Meanwhile, here is the patch for net-next-2.6
Your patch then can be applied after mine.
Thanks
[PATCH] net: RCU conversion of dev_getbyhwaddr() and arp_ioctl()
dev_getbyhwaddr() was called under RTNL.
Rename it to dev_getbyhwaddr_rcu() and change all its caller to now use
RCU locking instead of RTNL.
Change arp_ioctl() to use RCU instead of RTNL locking.
Note: this fix a dev refcount bug in llc
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bug has to do with boundary checks on the initial receive window.
If the initial receive window falls between init_cwnd and the
receive window specified by the user, the initial window is incorrectly
brought down to init_cwnd. The correct behavior is to allow it to
remain unchanged.
Signed-off-by: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Only when dont_send is 0, arp_filter() is consulted, so we can simply
assign the return value of arp_filter() to dont_send instead.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commits 9f0f7272 (ipv4: AF_INET link address family) and cf7afbfeb8
(rtnl: make link af-specific updates atomic) used incorrect
__in_dev_get_rcu() in RTNL protected contexts, triggering PROVE_RCU
warnings.
Switch to __in_dev_get_rtnl(), wich is more appropriate, since we hold
RTNL.
Based on a report and initial patch from Amerigo Wang.
Reported-by: Amerigo Wang <amwang@redhat.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Thomas Graf <tgraf@infradead.org>
Reviewed-by: WANG Cong <amwang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP_BASE_MSS is defined, but not used.
commit 5d424d5a introduce this macro, so use
it to initial sysctl_tcp_base_mss.
commit 5d424d5a67
Author: John Heffner <jheffner@psc.edu>
Date: Mon Mar 20 17:53:41 2006 -0800
[TCP]: MTU probing
Signed-off-by: Shan Wei <shanwei@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The only thing AF-specific about remembering the timestamp
for a time-wait TCP socket is getting the peer.
Abstract that behind a new timewait_sock_ops vector.
Support for real IPV6 sockets is not filled in yet, but
curiously this makes timewait recycling start to work
for v4-mapped ipv6 sockets.
Signed-off-by: David S. Miller <davem@davemloft.net>
If ipip is built as a module the 'ip tunnel add' command would fail because
the ipip module was not being autoloaded. Adding an alias for
the tunl0 device name cause dev_load() to autoload it when needed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If gre is built as a module the 'ip tunnel add' command would fail because
the ip_gre module was not being autoloaded. Adding an alias for
the gre0 device name cause dev_load() to autoload it when needed.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use strcpy() rather the sprintf() for the case where name is getting
generated. Fix indentation.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Then we can make a completely generic tcp_remember_stamp()
that uses ->get_peer() as a helper, minimizing the AF specific
code and minimizing the eventual code duplication when we implement
the ipv6 side of TW recycling.
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of directly accessing "peer", change to code to
operate using a "struct inet_peer_base *" pointer.
This will facilitate the addition of a seperate tree for
ipv6 peer entries.
Signed-off-by: David S. Miller <davem@davemloft.net>
inet sockets corresponding to passive connections are added to the bind hash
using ___inet_inherit_port(). These sockets are later removed from the bind
hash using __inet_put_port(). These two functions are not exactly symmetrical.
__inet_put_port() decrements hashinfo->bsockets and tb->num_owners, whereas
___inet_inherit_port() does not increment them. This results in both of these
going to -ve values.
This patch fixes this by calling inet_bind_hash() from ___inet_inherit_port(),
which does the right thing.
'bsockets' and 'num_owners' were introduced by commit a9d8f9110d
(inet: Allowing more than 64k connections and heavily optimize bind(0))
Signed-off-by: Nagendra Singh Tomar <tomer_iisc@yahoo.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_win_from_space() does the following:
if (sysctl_tcp_adv_win_scale <= 0)
return space >> (-sysctl_tcp_adv_win_scale);
else
return space - (space >> sysctl_tcp_adv_win_scale);
"space" is int.
As per C99 6.5.7 (3) shifting int for 32 or more bits is
undefined behaviour.
Indeed, if sysctl_tcp_adv_win_scale is exactly 32,
space >> 32 equals space and function returns 0.
Which means we busyloop in tcp_fixup_rcvbuf().
Restrict net.ipv4.tcp_adv_win_scale to [-31, 31].
Fix https://bugzilla.kernel.org/show_bug.cgi?id=20312
Steps to reproduce:
echo 32 >/proc/sys/net/ipv4/tcp_adv_win_scale
wget www.kernel.org
[softlockup]
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The /proc/net/tcp leaks openreq sockets from other namespaces.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As David pointed out correctly, updates to af-specific attributes
are currently not atomic. If multiple changes are requested and
one of them fails, previous updates may have been applied already
leaving the link behind in a undefined state.
This patch splits the function parse_link_af() into two functions
validate_link_af() and set_link_at(). validate_link_af() is placed
to validate_linkmsg() check for errors as early as possible before
any changes to the link have been made. set_link_af() is called to
commit the changes later.
This method is not fail proof, while it is currently sufficient
to make set_link_af() inerrable and thus 100% atomic, the
validation function method will not be able to detect all error
scenarios in the future, there will likely always be errors
depending on states which are f.e. not protected by rtnl_mutex
and thus may change between validation and setting.
Also, instead of silently ignoring unknown address families and
config blocks for address families which did not register a set
function the errors EAFNOSUPPORT respectively EOPNOSUPPORT are
returned to avoid comitting 4 out of 5 update requests without
notifying the user.
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In dev_pick_tx, don't do work in calculating queue
index or setting
the index in the sock unless the device has more than one queue. This
allows the sock to be set only with a queue index of a multi-queue
device which is desirable if device are stacked like in a tunnel.
We also allow the mapping of a socket to queue to be changed. To
maintain in order packet transmission a flag (ooo_okay) has been
added to the sk_buff structure. If a transport layer sets this flag
on a packet, the transmit queue can be changed for the socket.
Presumably, the transport would set this if there was no possbility
of creating OOO packets (for instance, there are no packets in flight
for the socket). This patch includes the modification in TCP output
for setting this flag.
Signed-off-by: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Changed Makefile to use <modules>-y instead of <modules>-objs
because -objs is deprecated and not mentioned in
Documentation/kbuild/makefiles.txt.
Signed-off-by: Tracey Dent <tdent48227@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We forgot to use __GFP_HIGHMEM in several __vmalloc() calls.
In ceph, add the missing flag.
In fib_trie.c, xfrm_hash.c and request_sock.c, using vzalloc() is
cleaner and allows using HIGHMEM pages as well.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
IGMP allocates MTU sized skbs. This may fail for large MTU (order-2
allocations), so add a fallback to try lower sizes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of iterating in_dev->mc_list from bonding driver, its better
to call a helper function provided by igmp.c
Details of implementation (locking) are private to igmp code.
ip_mc_rejoin_group(struct ip_mc_list *im) becomes
ip_mc_rejoin_groups(struct in_device *in_dev);
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
snprintf() returns number of bytes that were copied if there is no overflow.
This code uses return value as number of copied bytes. Theoretically format
string '%lu.%09lu %pI4:%u %pI4:%u %d %#x %#x %u %u %u %u\n' may be expanded
up to 163 bytes. In reality tv.tv_sec is just few bytes instead of 20, 2 ports
are just 5 bytes each instead of 10, length is 5 bytes instead of 10. The rest
is an unstrusted input. Theoretically if tv_sec is big then copy_to_user() would
overflow tbuf.
tbuf was increased to fit in 163 bytes. snprintf() is used to follow return
value semantic.
Signed-off-by: Vasiliy Kulikov <segoon@openwall.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the macros defined for the members of flowi to clean the code up.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implements the AF_INET link address family exposing the per
device configuration settings via netlink using the attribute
IFLA_INET_CONF.
The format of IFLA_INET_CONF differs depending on the direction
the attribute is sent. The attribute sent by the kernel consists
of a u32 array, basically a 1:1 copy of in_device->cnf.data[].
The attribute expected by the kernel must consist of a sequence
of nested u32 attributes, each representing a change request,
e.g.
[IFLA_INET_CONF] = {
[IPV4_DEVCONF_FORWARDING] = 1,
[IPV4_DEVCONF_NOXFRM] = 0,
}
libnl userspace API documentation and example available from:
http://www.infradead.org/~tgr/libnl/doc-git/group__link__inet.html
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current tcp_connect code completely ignores errors from sending an skb.
This makes sense in many situations (like -ENOBUFFS) but I want to be able to
immediately fail connections if they are denied by the SELinux netfilter hook.
Netfilter does not normally return ECONNREFUSED when it drops a packet so we
respect that error code as a final and fatal error that can not be recovered.
Based-on-patch-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: Eric Paris <eparis@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
otherwise xfrm_lookup will fail to find correct policy
Signed-off-by: Ulrich Weber <uweber@astaro.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP sockets refcount is usually 2, unless an incoming frame is going to
be queued in receive or backlog queue.
Using atomic_inc_not_zero_hint() permits to reduce latency, because
processor issues less memory transactions.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some of the documentation refers to web pages under
the domain `osdl.org'. However, `osdl.org' now
redirects to `linuxfoundation.org'.
Rather than rely on redirections, this patch updates
the addresses appropriately; for the most part, only
documentation that is meant to be current has been
updated.
The patch should be pretty quick to scan and check;
each new web-page url was gotten by trying out the
original URL in a browser and then simply copying the
the redirected URL (formatting as necessary).
There is some conflict as to which one of these domain
names is preferred:
linuxfoundation.org
linux-foundation.org
So, I wrote:
info@linuxfoundation.org
and got this reply:
Message-ID: <4CE17EE6.9040807@linuxfoundation.org>
Date: Mon, 15 Nov 2010 10:41:42 -0800
From: David Ames <david@linuxfoundation.org>
...
linuxfoundation.org is preferred. The canonical name for our web site is
www.linuxfoundation.org. Our list site is actually
lists.linux-foundation.org.
Regarding email linuxfoundation.org is preferred there are a few people
who choose to use linux-foundation.org for their own reasons.
Consequently, I used `linuxfoundation.org' for web pages and
`lists.linux-foundation.org' for mailing-list web pages and email addresses;
the only personal email address I updated from `@osdl.org' was that of
Andrew Morton, who prefers `linux-foundation.org' according `git log'.
Signed-off-by: Michael Witten <mfwitten@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The GRE Key field is intended to be used for identifying an individual
traffic flow within a tunnel. It is useful to be able to have XFRM
policy selector matches to have different policies for different
GRE tunnels.
Signed-off-by: Timo Teräs <timo.teras@iki.fi>
Signed-off-by: David S. Miller <davem@davemloft.net>
Avoid a sparse warning about 'ret' variable shadowing
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Use helpers to reduce number of sparse warnings
(CONFIG_SPARSE_RCU_POINTER=y)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
net/ipv4/igmp.c: In function 'ip_mc_inc_group':
net/ipv4/igmp.c:1228: error: implicit declaration of function 'for_each_pmc_rtnl'
net/ipv4/igmp.c:1228: error: expected ';' before '{' token
net/ipv4/igmp.c: In function 'ip_mc_unmap':
net/ipv4/igmp.c:1333: error: expected ';' before 'igmp_group_dropped'
...
Move for_each_pmc_rcu and for_each_pmc_rtnl macro definitions
outside of multicast ifdef protection.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
As we own the conntrack and the others can't see it until we confirm it,
we don't need to use atomic bit operation on ct->status.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
I am observing consistent behavior even with bridges, so let's unlock
this. xt_mac is already usable in FORWARD, too. Section 9 of
http://ebtables.sourceforge.net/br_fw_ia/br_fw_ia.html#section9 says
the MAC source address is changed, but my observation does not match
that claim -- the MAC header is retained.
Signed-off-by: Jan Engelhardt <jengelh@medozas.de>
[Patrick; code inspection seems to confirm this]
Signed-off-by: Patrick McHardy <kaber@trash.net>
Alexey Kuznetsov noticed a regression introduced by
commit f1ecd5d9e7
("Revert Backoff [v3]: Revert RTO on ICMP destination unreachable")
The RTO and timer modification code added to tcp_v4_err()
doesn't check sock_owned_by_user(), which if true means we
don't have exclusive access to the socket and therefore cannot
modify it's critical state.
Just skip this new code block if sock_owned_by_user() is true
and eliminate the now superfluous sock_owned_by_user() code
block contained within.
Reported-by: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC: Damian Lukowski <damian@tvk.rwth-aachen.de>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
in_dev->mc_list is protected by one rwlock (in_dev->mc_list_lock).
This can easily be converted to a RCU protection.
Writers hold RTNL, so mc_list_lock is removed, not replaced by a
spinlock.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Cypher Wu <cypher.w@gmail.com>
Cc: Américo Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we test rt->fl.iif against zero, we're seeing if it's
an output or an input route.
Make that explicit with some helper functions.
Signed-off-by: David S. Miller <davem@davemloft.net>
It seems idev field in struct rtable has no special purpose, but adding
extra atomic ops.
We hold refcounts on the device itself (using percpu data, so pretty
cheap in current kernel).
infiniband case is solved using dst.dev instead of idev->dev
Removal of this field means routing without route cache is now using
shared data, percpu data, and only potential contention is a pair of
atomic ops on struct neighbour per forwarded packet.
About 5% speedup on routing test.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Roland Dreier <rolandd@cisco.com>
Cc: Sean Hefty <sean.hefty@intel.com>
Cc: Hal Rosenstock <hal.rosenstock@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted by Steve Chen, since commit
f5fff5dc8a ("tcp: advertise MSS
requested by user") we can end up with a situation where
tcp_select_initial_window() does a divide by a zero (or
even negative) mss value.
The problem is that sometimes we effectively subtract
TCPOLEN_TSTAMP_ALIGNED and/or TCPOLEN_MD5SIG_ALIGNED from the mss.
Fix this by increasing the minimum from 8 to 64.
Reported-by: Steve Chen <schen@mvista.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Robin Holt tried to boot a 16TB machine and found some limits were
reached : sysctl_tcp_mem[2], sysctl_udp_mem[2]
We can switch infrastructure to use long "instead" of "int", now
atomic_long_t primitives are available for free.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Reported-by: Robin Holt <holt@sgi.com>
Reviewed-by: Robin Holt <holt@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Coalesce long formats.
Align arguments.
Remove KERN_<level>.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 8723e1b4ad (inet: RCU changes in inetdev_by_index())
forgot one call site in ip_mc_drop_socket()
We should not decrease idev refcount after inetdev_by_index() call,
since refcount is not increased anymore.
Reported-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Reported-by: Miles Lane <miles.lane@gmail.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We were using nlmsg_find_attr() to look up the bytecode by attribute when
auditing, but then just using the first attribute when actually running
bytecode. So, if we received a message with two attribute elements, where only
the second had type INET_DIAG_REQ_BYTECODE, we would validate and run different
bytecode strings.
Fix this by consistently using nlmsg_find_attr everywhere.
Signed-off-by: Nelson Elhage <nelhage@ksplice.com>
Signed-off-by: Thomas Graf <tgraf@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After commit ebc0ffae5 (RCU conversion of fib_lookup()),
fib_result_assign() should not change fib refcounts anymore.
Thanks to Michael who did the bisection and bug report.
Reported-by: Michael Ellerman <michael@ellerman.id.au>
Tested-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Structure ipt_getinfo is copied to userland with the field "name"
that has the last elements unitialized. It leads to leaking of
contents of kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Structure arpt_getinfo is copied to userland with the field "name"
that has the last elements unitialized. It leads to leaking of
contents of kernel stack memory.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Before making the fallback tunnel visible to lookups, we should make
sure it is completely setup, once ipgre_tunnel_init() had been called
and tstats per_cpu pointer allocated.
move rcu_assign_pointer(ign->tunnels_wc[0], tunnel); from
ipgre_fb_tunnel_init() to ipgre_init_net()
Based on a patch from Pavel Emelyanov
Reported-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
net/ipv4/netfilter/nf_nat_core.c:52: warning: 'nf_nat_proto_find_get' defined but not used
net/ipv4/netfilter/nf_nat_core.c:66: warning: 'nf_nat_proto_put' defined but not used
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
When we stop a namespace we flush the table and free one, but the
added fn_zone-s (and their hashes if grown) are leaked. Need to free.
Tries releases all its stuff in the flushing code.
Shame on us - this bug exists since the very first make-fib-per-net
patches in 2.6.27 :(
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
After making rcu protection for tunnels (ipip, gre, sit and ip6) a bug
was introduced into the SIOCCHGTUNNEL code.
The tunnel is first unlinked, then addresses change, then it is linked
back probably into another bucket. But while changing the parms, the
hash table is unlocked to readers and they can lookup the improper tunnel.
Respective commits are b7285b79 (ipip: get rid of ipip_lock), 1507850b
(gre: get rid of ipgre_lock), 3a43be3c (sit: get rid of ipip6_lock) and
94767632 (ip6tnl: get rid of ip6_tnl_lock).
The quick fix is to wait for quiescent state to pass after unlinking,
but if it is inappropriate I can invent something better, just let me
know.
Signed-off-by: Pavel Emelyanov <xemul@openvz.org>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adds __rcu annotations to inetpeer
(struct inet_peer)->avl_left
(struct inet_peer)->avl_right
This is a tedious cleanup, but removes one smp_wmb() from link_to_pool()
since we now use more self documenting rcu_assign_pointer().
Note the use of RCU_INIT_POINTER() instead of rcu_assign_pointer() in
all cases we dont need a memory barrier.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __rcu annotations to :
(struct ip_tunnel)->prl
(struct ip_tunnel_prl_entry)->next
(struct xfrm_tunnel)->next
struct xfrm_tunnel *tunnel4_handlers
struct xfrm_tunnel *tunnel64_handlers
And use appropriate rcu primitives to reduce sparse warnings if
CONFIG_SPARSE_RCU_POINTER=y
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __rcu annotations to :
struct net_protocol *inet_protos
struct net_protocol *inet6_protos
And use appropriate casts to reduce sparse warnings if
CONFIG_SPARSE_RCU_POINTER=y
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __rcu annotations to :
(struct dst_entry)->rt_next
(struct rt_hash_bucket)->chain
And use appropriate rcu primitives to reduce sparse warnings if
CONFIG_SPARSE_RCU_POINTER=y
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While fixing CONFIG_SPARSE_RCU_POINTER errors, I had to fix accesses to
fz->fz_hash for real.
- &fz->fz_hash[fn_hash(f->fn_key, fz)]
+ rcu_dereference(fz->fz_hash) + fn_hash(f->fn_key, fz)
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __rcu annotations to :
(struct ip_ra_chain)->next
struct ip_ra_chain *ip_ra_chain;
And use appropriate rcu primitives.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add __rcu annotation to :
(struct sock)->sk_filter
And use appropriate rcu primitives to reduce sparse warnings if
CONFIG_SPARSE_RCU_POINTER=y
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
(struct ip6_tnl)->next is rcu protected :
(struct ip_tunnel)->next is rcu protected :
(struct xfrm6_tunnel)->next is rcu protected :
add __rcu annotation and proper rcu primitives.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1699 commits)
bnx2/bnx2x: Unsupported Ethtool operations should return -EINVAL.
vlan: Calling vlan_hwaccel_do_receive() is always valid.
tproxy: use the interface primary IP address as a default value for --on-ip
tproxy: added IPv6 support to the socket match
cxgb3: function namespace cleanup
tproxy: added IPv6 support to the TPROXY target
tproxy: added IPv6 socket lookup function to nf_tproxy_core
be2net: Changes to use only priority codes allowed by f/w
tproxy: allow non-local binds of IPv6 sockets if IP_TRANSPARENT is enabled
tproxy: added tproxy sockopt interface in the IPV6 layer
tproxy: added udp6_lib_lookup function
tproxy: added const specifiers to udp lookup functions
tproxy: split off ipv6 defragmentation to a separate module
l2tp: small cleanup
nf_nat: restrict ICMP translation for embedded header
can: mcp251x: fix generation of error frames
can: mcp251x: fix endless loop in interrupt handler if CANINTF_MERRF is set
can-raw: add msg_flags to distinguish local traffic
9p: client code cleanup
rds: make local functions/variables static
...
Fix up conflicts in net/core/dev.c, drivers/net/pcmcia/smc91c92_cs.c and
drivers/net/wireless/ath/ath9k/debug.c as per David
* 'llseek' of git://git.kernel.org/pub/scm/linux/kernel/git/arnd/bkl:
vfs: make no_llseek the default
vfs: don't use BKL in default_llseek
llseek: automatically add .llseek fop
libfs: use generic_file_llseek for simple_attr
mac80211: disallow seeks in minstrel debug code
lirc: make chardev nonseekable
viotape: use noop_llseek
raw: use explicit llseek file operations
ibmasmfs: use generic_file_llseek
spufs: use llseek in all file operations
arm/omap: use generic_file_llseek in iommu_debug
lkdtm: use generic_file_llseek in debugfs
net/wireless: use generic_file_llseek in debugfs
drm: use noop_llseek
Dave Jones