The AMBA bus should also use of_device_make_bus_id() when populating device
out of device tree data. This patch makes the function non-static, and
adds a suitable prototype in of_device.h
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Fix __task_cred()'s lockdep check by removing the following validation
condition:
lockdep_tasklist_lock_is_held()
as commit_creds() does not take the tasklist_lock, and nor do most of the
functions that call it, so this check is pointless and it can prevent
detection of the RCU lock not being held if the tasklist_lock is held.
Instead, add the following validation condition:
task->exit_state >= 0
to permit the access if the target task is dead and therefore unable to change
its own credentials.
Fix __task_cred()'s comment to:
(1) discard the bit that says that the caller must prevent the target task
from being deleted. That shouldn't need saying.
(2) Add a comment indicating the result of __task_cred() should not be passed
directly to get_cred(), but rather than get_task_cred() should be used
instead.
Also put a note into the documentation to enforce this point there too.
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
It's possible for get_task_cred() as it currently stands to 'corrupt' a set of
credentials by incrementing their usage count after their replacement by the
task being accessed.
What happens is that get_task_cred() can race with commit_creds():
TASK_1 TASK_2 RCU_CLEANER
-->get_task_cred(TASK_2)
rcu_read_lock()
__cred = __task_cred(TASK_2)
-->commit_creds()
old_cred = TASK_2->real_cred
TASK_2->real_cred = ...
put_cred(old_cred)
call_rcu(old_cred)
[__cred->usage == 0]
get_cred(__cred)
[__cred->usage == 1]
rcu_read_unlock()
-->put_cred_rcu()
[__cred->usage == 1]
panic()
However, since a tasks credentials are generally not changed very often, we can
reasonably make use of a loop involving reading the creds pointer and using
atomic_inc_not_zero() to attempt to increment it if it hasn't already hit zero.
If successful, we can safely return the credentials in the knowledge that, even
if the task we're accessing has released them, they haven't gone to the RCU
cleanup code.
We then change task_state() in procfs to use get_task_cred() rather than
calling get_cred() on the result of __task_cred(), as that suffers from the
same problem.
Without this change, a BUG_ON in __put_cred() or in put_cred_rcu() can be
tripped when it is noticed that the usage count is not zero as it ought to be,
for example:
kernel BUG at kernel/cred.c:168!
invalid opcode: 0000 [#1] SMP
last sysfs file: /sys/kernel/mm/ksm/run
CPU 0
Pid: 2436, comm: master Not tainted 2.6.33.3-85.fc13.x86_64 #1 0HR330/OptiPlex
745
RIP: 0010:[<ffffffff81069881>] [<ffffffff81069881>] __put_cred+0xc/0x45
RSP: 0018:ffff88019e7e9eb8 EFLAGS: 00010202
RAX: 0000000000000001 RBX: ffff880161514480 RCX: 00000000ffffffff
RDX: 00000000ffffffff RSI: ffff880140c690c0 RDI: ffff880140c690c0
RBP: ffff88019e7e9eb8 R08: 00000000000000d0 R09: 0000000000000000
R10: 0000000000000001 R11: 0000000000000040 R12: ffff880140c690c0
R13: ffff88019e77aea0 R14: 00007fff336b0a5c R15: 0000000000000001
FS: 00007f12f50d97c0(0000) GS:ffff880007400000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 00007f8f461bc000 CR3: 00000001b26ce000 CR4: 00000000000006f0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400
Process master (pid: 2436, threadinfo ffff88019e7e8000, task ffff88019e77aea0)
Stack:
ffff88019e7e9ec8 ffffffff810698cd ffff88019e7e9ef8 ffffffff81069b45
<0> ffff880161514180 ffff880161514480 ffff880161514180 0000000000000000
<0> ffff88019e7e9f28 ffffffff8106aace 0000000000000001 0000000000000246
Call Trace:
[<ffffffff810698cd>] put_cred+0x13/0x15
[<ffffffff81069b45>] commit_creds+0x16b/0x175
[<ffffffff8106aace>] set_current_groups+0x47/0x4e
[<ffffffff8106ac89>] sys_setgroups+0xf6/0x105
[<ffffffff81009b02>] system_call_fastpath+0x16/0x1b
Code: 48 8d 71 ff e8 7e 4e 15 00 85 c0 78 0b 8b 75 ec 48 89 df e8 ef 4a 15 00
48 83 c4 18 5b c9 c3 55 8b 07 8b 07 48 89 e5 85 c0 74 04 <0f> 0b eb fe 65 48 8b
04 25 00 cc 00 00 48 3b b8 58 04 00 00 75
RIP [<ffffffff81069881>] __put_cred+0xc/0x45
RSP <ffff88019e7e9eb8>
---[ end trace df391256a100ebdd ]---
Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds the DMA context programming and userspace ABI for multichannel
reception, i.e. for listening on multiple channel numbers by means of a
single DMA context.
The use case is reception of more streams than there are IR DMA units
offered by the link layer. This is already implemented by the older
ohci1394 + ieee1394 + raw1394 stack. And as discussed recently on
linux1394-devel, this feature is occasionally used in practice.
The big drawbacks of this mode are that buffer layout and interrupt
generation necessarily differ from single-channel reception: Headers
and trailers are not stripped from packets, packets are not aligned with
buffer chunks, interrupts are per buffer chunk, not per packet.
These drawbacks also cause a rather hefty code footprint to support this
rarely used OHCI-1394 feature. (367 lines added, among them 94 lines of
added userspace ABI documentation.)
This implementation enforces that a multichannel reception context may
only listen to channels to which no single-channel context on the same
link layer is presently listening to. OHCI-1394 would allow to overlay
single-channel contexts by the multi-channel context, but this would be
a departure from the present first-come-first-served policy of IR
context creation.
The implementation is heavily based on an earlier one by Jay Fenlason.
Thanks Jay.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Platforms may have some external power control which need to be
controlled from board specific code. Rename the translate_vdd()
callback to vdd_handler() and pass it the power mode.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
A small number of users of IRQF_TIMER are using it for the implied no
suspend behaviour on interrupts which are not timer interrupts.
Therefore add a new IRQF_NO_SUSPEND flag, rename IRQF_TIMER to
__IRQF_TIMER and redefine IRQF_TIMER in terms of these new flags.
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: xen-devel@lists.xensource.com
Cc: linux-input@vger.kernel.org
Cc: linuxppc-dev@ozlabs.org
Cc: devicetree-discuss@lists.ozlabs.org
LKML-Reference: <1280398595-29708-1-git-send-email-ian.campbell@citrix.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
davinci: da850/omap-l138 evm: account for DEFDCDC{2,3} being tied high
regulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH register
wm8350-regulator: fix wm8350_register_regulator error handling
ab3100: fix off-by-one value range checking for voltage selector
fanotify currently, when given a vfsmount_mark will look up (if it exists)
the corresponding inode mark. This patch drops that lookup and uses the
mark provided.
Signed-off-by: Eric Paris <eparis@redhat.com>
should_send_event() and handle_event() will both need to look up the inode
event if they get a vfsmount event. Lets just pass both at the same time
since we have them both after walking the lists in lockstep.
Signed-off-by: Eric Paris <eparis@redhat.com>
The global fsnotify groups lists were invented as a way to increase the
performance of fsnotify by shortcutting events which were not interesting.
With the changes to walk the object lists rather than global groups lists
these shortcuts are not useful.
Signed-off-by: Eric Paris <eparis@redhat.com>
group->mask is now useless. It was originally a shortcut for fsnotify to
save on performance. These checks are now redundant, so we remove them.
Signed-off-by: Eric Paris <eparis@redhat.com>
Because we walk the object->fsnotify_marks list instead of the global
fsnotify groups list we don't need the fsnotify_inode_mask and
fsnotify_vfsmount_mask as these were simply shortcuts in fsnotify() for
performance. They are now extra checks, rip them out.
Signed-off-by: Eric Paris <eparis@redhat.com>
With the change of fsnotify to use srcu walking the marks list instead of
walking the global groups list we now know the mark in question. The code can
send the mark to the group's handling functions and the groups won't have to
find those marks themselves.
Signed-off-by: Eric Paris <eparis@redhat.com>
Currently reading the inode->i_fsnotify_marks or
vfsmount->mnt_fsnotify_marks lists are protected by a spinlock on both the
read and the write side. This patch protects the read side of those lists
with a new single srcu.
Signed-off-by: Eric Paris <eparis@redhat.com>
Currently fsnotify check is mark->group is NULL to decide if
fsnotify_destroy_mark() has already been called or not. With the upcoming
rcu work it is a heck of a lot easier to use an explicit flag than worry
about group being set to NULL.
Signed-off-by: Eric Paris <eparis@redhat.com>
Al explains that calling dentry_open() with a mnt/dentry pair is only
garunteed to be safe if they are already used in an open struct file. To
make sure this is the case don't store and use a struct path in fsnotify,
always use a struct file.
Signed-off-by: Eric Paris <eparis@redhat.com>
Rather than the horrific void ** argument and such just to pass the
fanotify_merge event back to the caller of fsnotify_add_notify_event() have
those things return an event if it was different than the event suggusted to
be added.
Signed-off-by: Eric Paris <eparis@redhat.com>
Currently fanotify fds opened for thier listeners are done with f_flags
equal to O_RDONLY | O_LARGEFILE. This patch instead takes f_flags from the
fanotify_init syscall and uses those when opening files in the context of
the listener.
Signed-off-by: Eric Paris <eparis@redhat.com>
This patch adds a check to make sure that all fsnotify bits are unique and we
cannot accidentally use the same bit for 2 different fsnotify event types.
Signed-off-by: Eric Paris <eparis@redhat.com>
inotify uses bits called IN_* and fsnotify uses bits called FS_*. These
need to line up. This patch adds build time checks to make sure noone can
change these bits so they are not the same.
Signed-off-by: Eric Paris <eparis@redhat.com>
An inotify watch on a directory will send events for children even if those
children have been unlinked. This patch add a new inotify flag IN_EXCL_UNLINK
which allows a watch to specificy they don't care about unlinked children.
This should fix performance problems seen by tasks which add a watch to
/tmp and then are overrun with events when other processes are reading and
writing to unlinked files they created in /tmp.
https://bugzilla.kernel.org/show_bug.cgi?id=16296
Requested-by: Matthias Clasen <mclasen@redhat.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
In TPS6507x, depending on the status of DEFDCDC{2,3} pin either
DEFDCDC{2,3}_LOW or DEFDCDC{2,3}_HIGH register needs to be read or
programmed to change the output voltage.
The current driver assumes DEFDCDC{2,3} pins are always tied low
and thus operates only on DEFDCDC{2,3}_LOW register. This need
not always be the case (as is found on OMAP-L138 EVM).
Unfortunately, software cannot read the status of DEFDCDC{2,3} pins.
So, this information is passed through platform data depending on
how the board is wired.
Signed-off-by: Anuj Aggarwal <anuj.aggarwal@ti.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
akpm got a warning the fsnotify_mask could be used uninitialized in
fsnotify_perm(). It's not actually possible but his compiler complained
about it. This patch just initializes it to 0 to shut up the compiler.
Reported-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Eric Paris <eparis@redhat.com>
fanotify groups need to respond to events which include permissions types.
To do so groups will send a response using write() on the fanotify_fd they
have open.
Signed-off-by: Eric Paris <eparis@redhat.com>
This is the backend work needed for fanotify to support the new
FS_OPEN_PERM and FS_ACCESS_PERM fsnotify events. This is done using the
new fsnotify secondary queue. No userspace interface is provided actually
respond to or request these events.
Signed-off-by: Eric Paris <eparis@redhat.com>
introduce a new fsnotify hook, fsnotify_perm(), which is called from the
security code. This hook is used to allow fsnotify groups to make access
control decisions about events on the system. We also must change the
generic fsnotify function to return an error code if we intend these hooks
to be in any way useful.
Signed-off-by: Eric Paris <eparis@redhat.com>
Extern declarations in sysctl.c should be move to their own head file, and
then include them in relavant .c files.
Move inotify_table extern declaration to linux/inotify.h
Signed-off-by: Dave Young <hidave.darkstar@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Eric Paris <eparis@redhat.com>
Move dir_notify_enable declaration to where it belongs -- dnotify.h .
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
fsnotify was using char * when it passed around the d_name.name string
internally but it is actually an unsigned char *. This patch switches
fsnotify to use unsigned and should silence some pointer signess warnings
which have popped out of xfs. I do not add -Wpointer-sign to the fsnotify
code as there are still issues with kstrdup and strlen which would pop
out needless warnings.
Signed-off-by: Eric Paris <eparis@redhat.com>
Each group can define their own notification (and secondary_q) merge
function. Inotify does tail drop, fanotify does matching and drop which
can actually allocate a completely new event. But for fanotify to properly
deal with permissions events it needs to know the new event which was
ultimately added to the notification queue. This patch just implements a
void ** argument which is passed to the merge function. fanotify can use
this field to pass the new event back to higher layers.
Signed-off-by: Eric Paris <eparis@redhat.com>
for fanotify to properly deal with permissions events
This introduces an ordering to fsnotify groups. With purely asynchronous
notification based "things" implementing fsnotify (inotify, dnotify) ordering
isn't particularly important. But if people want to use fsnotify for the
basis of sycronous notification or blocking notification ordering becomes
important.
eg. A Hierarchical Storage Management listener would need to get its event
before an AV scanner could get its event (since the HSM would need to
bring the data in for the AV scanner to scan.) Typically asynchronous notification
would want to run after the AV scanner made any relevant access decisions
so as to not send notification about an event that was denied.
Signed-off-by: Eric Paris <eparis@redhat.com>
fanotify listeners may want to clear all marks. They may want to do this
to destroy all of their inode marks which have nothing but ignores.
Realistically this is useful for av vendors who update policy and want to
clear all of their cached allows.
Signed-off-by: Eric Paris <eparis@redhat.com>
Some users may want to truely ignore an inode even if it has been modified.
Say you are wanting a mount which contains a log file and you really don't
want any notification about that file. This patch allows the listener to
do that.
Signed-off-by: Eric Paris <eparis@redhat.com>
Some inodes a group may want to never hear about a set of events even if
the inode is modified. We add a new mark flag which indicates that these
marks should not have their ignored_mask cleared on modification.
Signed-off-by: Eric Paris <eparis@redhat.com>
Change the sys_fanotify_mark() system call so users can set ignored_masks
on inodes. Remember, if a user new sets a real mask, and only sets ignored
masks, the ignore will never be pinned in memory. Thus ignored_masks can
be lost under memory pressure and the user may again get events they
previously thought were ignored.
Signed-off-by: Eric Paris <eparis@redhat.com>
The ignored_mask is a new mask which is part of fsnotify marks. A group's
should_send_event() function can use the ignored mask to determine that
certain events are not of interest. In particular if a group registers a
mask including FS_OPEN on a vfsmount they could add FS_OPEN to the
ignored_mask for individual inodes and not send open events for those
inodes.
Signed-off-by: Eric Paris <eparis@redhat.com>
inotify marks must pin inodes in core. dnotify doesn't technically need to
since they are closed when the directory is closed. fanotify also need to
pin inodes in core as it works today. But the next step is to introduce
the concept of 'ignored masks' which is actually a mask of events for an
inode of no interest. I claim that these should be liberally sent to the
kernel and should not pin the inode in core. If the inode is brought back
in the listener will get an event it may have thought excluded, but this is
not a serious situation and one any listener should deal with.
This patch lays the ground work for non-pinning inode marks by using lazy
inode pinning. We do not pin a mark until it has a non-zero mask entry. If a
listener new sets a mask we never pin the inode.
Signed-off-by: Eric Paris <eparis@redhat.com>
fanotify_mark_validate functions are all needlessly declared in headers as
static inlines. Instead just do the checks where they are needed for code
readability.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Eric Paris <eparis@redhat.com>
the term 'vfsmount' isn't sensicle to userspace. instead call is 'mount.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Eric Paris <eparis@redhat.com>
Create a new fanotify_mark flag which indicates we should attach the mark
to the vfsmount holding the object referenced by dfd and pathname rather
than the inode itself.
Signed-off-by: Eric Paris <eparis@redhat.com>
currently should_send_event in fanotify only cares about marks on inodes.
This patch extends that interface to indicate that it cares about events
that happened on vfsmounts.
Signed-off-by: Eric Paris <eparis@redhat.com>
Per-mount watches allow groups to listen to fsnotify events on an entire
mount. This patch simply adds and initializes the fields needed in the
vfsmount struct to make this happen.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Eric Paris <eparis@redhat.com>
Much like inode-mark.c has all of the code dealing with marks on inodes
this patch adds a vfsmount-mark.c which has similar code but is intended
for marks on vfsmounts.
Signed-off-by: Eric Paris <eparis@redhat.com>
This patch adds the list and mask fields needed to support vfsmount marks.
These are the same fields fsnotify needs on an inode. They are not used,
just declared and we note where the cleanup hook should be (the function is
not yet defined)
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Eric Paris <eparis@redhat.com>
currently all marking is done by functions in inode-mark.c. Some of this
is pretty generic and should be instead done in a generic function and we
should only put the inode specific code in inode-mark.c
Signed-off-by: Eric Paris <eparis@redhat.com>
Pass the process identifiers of the triggering processes to fanotify
listeners: this information is useful for event filtering and logging.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Eric Paris <eparis@redhat.com>
Send events to userspace by reading the file descriptor from fanotify_init().
One will get blocks of data which look like:
struct fanotify_event_metadata {
__u32 event_len;
__u32 vers;
__s32 fd;
__u64 mask;
__s64 pid;
__u64 cookie;
} __attribute__ ((packed));
Simple code to retrieve and deal with events is below
while ((len = read(fan_fd, buf, sizeof(buf))) > 0) {
struct fanotify_event_metadata *metadata;
metadata = (void *)buf;
while(FAN_EVENT_OK(metadata, len)) {
[PROCESS HERE!!]
if (metadata->fd >= 0 && close(metadata->fd) != 0)
goto fail;
metadata = FAN_EVENT_NEXT(metadata, len);
}
}
Signed-off-by: Eric Paris <eparis@redhat.com>
NAME
fanotify_mark - add, remove, or modify an fanotify mark on a
filesystem object
SYNOPSIS
int fanotify_mark(int fanotify_fd, unsigned int flags, u64 mask,
int dfd, const char *pathname)
DESCRIPTION
fanotify_mark() is used to add remove or modify a mark on a filesystem
object. Marks are used to indicate that the fanotify group is
interested in events which occur on that object. At this point in
time marks may only be added to files and directories.
fanotify_fd must be a file descriptor returned by fanotify_init()
The flags field must contain exactly one of the following:
FAN_MARK_ADD - or the bits in mask and ignored mask into the mark
FAN_MARK_REMOVE - bitwise remove the bits in mask and ignored mark
from the mark
The following values can be OR'd into the flags field:
FAN_MARK_DONT_FOLLOW - same meaning as O_NOFOLLOW as described in open(2)
FAN_MARK_ONLYDIR - same meaning as O_DIRECTORY as described in open(2)
dfd may be any of the following:
AT_FDCWD: the object will be lookup up based on pathname similar
to open(2)
file descriptor of a directory: if pathname is not NULL the
object to modify will be lookup up similar to openat(2)
file descriptor of the final object: if pathname is NULL the
object to modify will be the object referenced by dfd
The mask is the bitwise OR of the set of events of interest such as:
FAN_ACCESS - object was accessed (read)
FAN_MODIFY - object was modified (write)
FAN_CLOSE_WRITE - object was writable and was closed
FAN_CLOSE_NOWRITE - object was read only and was closed
FAN_OPEN - object was opened
FAN_EVENT_ON_CHILD - interested in objected that happen to
children. Only relavent when the object
is a directory
FAN_Q_OVERFLOW - event queue overflowed (not implemented)
RETURN VALUE
On success, this system call returns 0. On error, -1 is
returned, and errno is set to indicate the error.
ERRORS
EINVAL An invalid value was specified in flags.
EINVAL An invalid value was specified in mask.
EINVAL An invalid value was specified in ignored_mask.
EINVAL fanotify_fd is not a file descriptor as returned by
fanotify_init()
EBADF fanotify_fd is not a valid file descriptor
EBADF dfd is not a valid file descriptor and path is NULL.
ENOTDIR dfd is not a directory and path is not NULL
EACCESS no search permissions on some part of the path
ENENT file not found
ENOMEM Insufficient kernel memory is available.
CONFORMING TO
These system calls are Linux-specific.
Signed-off-by: Eric Paris <eparis@redhat.com>
This patch simply declares the new sys_fanotify_mark syscall
int fanotify_mark(int fanotify_fd, unsigned int flags, u64_mask,
int dfd const char *pathname)
Signed-off-by: Eric Paris <eparis@redhat.com>
NAME
fanotify_init - initialize an fanotify group
SYNOPSIS
int fanotify_init(unsigned int flags, unsigned int event_f_flags, int priority);
DESCRIPTION
fanotify_init() initializes a new fanotify instance and returns a file
descriptor associated with the new fanotify event queue.
The following values can be OR'd into the flags field:
FAN_NONBLOCK Set the O_NONBLOCK file status flag on the new open file description.
Using this flag saves extra calls to fcntl(2) to achieve the same
result.
FAN_CLOEXEC Set the close-on-exec (FD_CLOEXEC) flag on the new file descriptor.
See the description of the O_CLOEXEC flag in open(2) for reasons why
this may be useful.
The event_f_flags argument is unused and must be set to 0
The priority argument is unused and must be set to 0
RETURN VALUE
On success, this system call return a new file descriptor. On error, -1 is
returned, and errno is set to indicate the error.
ERRORS
EINVAL An invalid value was specified in flags.
EINVAL A non-zero valid was passed in event_f_flags or in priority
ENFILE The system limit on the total number of file descriptors has been reached.
ENOMEM Insufficient kernel memory is available.
CONFORMING TO
These system calls are Linux-specific.
Signed-off-by: Eric Paris <eparis@redhat.com>
This patch defines a new syscall fanotify_init() of the form:
int sys_fanotify_init(unsigned int flags, unsigned int event_f_flags,
unsigned int priority)
This syscall is used to create and fanotify group. This is very similar to
the inotify_init() syscall.
Signed-off-by: Eric Paris <eparis@redhat.com>
fanotify is a novel file notification system which bases notification on
giving userspace both an event type (open, close, read, write) and an open
file descriptor to the object in question. This should address a number of
races and problems with other notification systems like inotify and dnotify
and should allow the future implementation of blocking or access controlled
notification. These are useful for on access scanners or hierachical storage
management schemes.
This patch just implements the basics of the fsnotify functions.
Signed-off-by: Eric Paris <eparis@redhat.com>
sparc used the same value as FMODE_NONOTIFY so change FMODE_NONOTIFY to be
something unique.
Signed-off-by: Wu Fengguang <fengguang.wu@intel.com>
Signed-off-by: Eric Paris <eparis@redhat.com>
This is a new f_mode which can only be set by the kernel. It indicates
that the fd was opened by fanotify and should not cause future fanotify
events. This is needed to prevent fanotify livelock. An example of
obvious livelock is from fanotify close events.
Process A closes file1
This creates a close event for file1.
fanotify opens file1 for Listener X
Listener X deals with the event and closes its fd for file1.
This creates a close event for file1.
fanotify opens file1 for Listener X
Listener X deals with the event and closes its fd for file1.
This creates a close event for file1.
fanotify opens file1 for Listener X
Listener X deals with the event and closes its fd for file1.
notice a pattern?
The fix is to add the FMODE_NONOTIFY bit to the open filp done by the kernel
for fanotify. Thus when that file is used it will not generate future
events.
This patch simply defines the bit.
Signed-off-by: Eric Paris <eparis@redhat.com>
previously I used mark_entry when talking about marks on inodes. The
_entry is pretty useless. Just use "mark" instead.
Signed-off-by: Eric Paris <eparis@redhat.com>
Some fsnotify operations send a struct file. This is more information than
we technically need. We instead send a struct path in all cases instead of
sometimes a path and sometimes a file.
Signed-off-by: Andreas Gruenbacher <agruen@suse.de>
Signed-off-by: Eric Paris <eparis@redhat.com>
To differentiate between inode and vfsmount (or other future) types of
marks we add a flags field and set the inode bit on inode marks (the only
currently supported type of mark)
Signed-off-by: Eric Paris <eparis@redhat.com>
vfsmount marks need mostly the same data as inode specific fields, but for
consistency and understandability we put that data in a vfsmount specific
struct inside a union with inode specific data.
Signed-off-by: Eric Paris <eparis@redhat.com>
The addition of marks on vfs mounts will be simplified if the inode
specific parts of a mark and the vfsmnt specific parts of a mark are
actually in a union so naming can be easy. This patch just implements the
inode struct and the union.
Signed-off-by: Eric Paris <eparis@redhat.com>
To ensure that a group will not duplicate events when it receives it based
on the vfsmount and the inode should_send_event test we should distinguish
those two cases. We pass a vfsmount to this function so groups can make
their own determinations.
Signed-off-by: Eric Paris <eparis@redhat.com>
currently all of the notification systems implemented select which inodes
they care about and receive messages only about those inodes (or the
children of those inodes.) This patch begins to flesh out fsnotify support
for the concept of listeners that want to hear notification for an inode
accessed below a given monut point. This patch implements a second list
of fsnotify groups to hold these types of groups and a second global mask
to hold the events of interest for this type of group.
The reason we want a second group list and mask is because the inode based
notification should_send_event support which makes each group look for a mark
on the given inode. With one nfsmount listener that means that every group would
have to take the inode->i_lock, look for their mark, not find one, and return
for every operation. By seperating vfsmount from inode listeners only when
there is a inode listener will the inode groups have to look for their
mark and take the inode lock. vfsmount listeners will have to grab the lock and
look for a mark but there should be fewer of them, and one vfsmount listener
won't cause the i_lock to be grabbed and released for every fsnotify group
on every io operation.
Signed-off-by: Eric Paris <eparis@redhat.com>
Simple renaming patch. fsnotify is about to support mount point listeners
so I am renaming fsnotify_groups and fsnotify_mask to indicate these are lists
used only for groups which have watches on inodes.
Signed-off-by: Eric Paris <eparis@redhat.com>
fsnotify_obtain_group was intended to be able to find an already existing
group. Nothing uses that functionality. This just renames it to
fsnotify_alloc_group so it is clear what it is doing.
Signed-off-by: Eric Paris <eparis@redhat.com>
The original fsnotify interface has a group-num which was intended to be
able to find a group after it was added. I no longer think this is a
necessary thing to do and so we remove the group_num.
Signed-off-by: Eric Paris <eparis@redhat.com>
fanotify would like to clone events already on its notification list, make
changes to the new event, and then replace the old event on the list with
the new event. This patch implements the replace functionality of that
process.
Signed-off-by: Eric Paris <eparis@redhat.com>
fsnotify_clone_event will take an event, clone it, and return the cloned
event to the caller. Since events may be in use by multiple fsnotify
groups simultaneously certain event entries (such as the mask) cannot be
changed after the event was created. Since fanotify would like to merge
events happening on the same file it needs a new clean event to work with
so it can change any fields it wishes.
Signed-off-by: Eric Paris <eparis@redhat.com>
inotify only wishes to merge a new event with the last event on the
notification fifo. fanotify is willing to merge any events including by
means of bitwise OR masks of multiple events together. This patch moves
the inotify event merging logic out of the generic fsnotify notification.c
and into the inotify code. This allows each use of fsnotify to provide
their own merge functionality.
Signed-off-by: Eric Paris <eparis@redhat.com>
fanotify needs a path in order to open an fd to the object which changed.
Currently notifications to inode's parents are done using only the inode.
For some parental notification we have the entire file, send that so
fanotify can use it.
Signed-off-by: Eric Paris <eparis@redhat.com>
fanotify, the upcoming notification system actually needs a struct path so it can
do opens in the context of listeners, and it needs a file so it can get f_flags
from the original process. Close was the only operation that already was passing
a struct file to the notification hook. This patch passes a file for access,
modify, and open as well as they are easily available to these hooks.
Signed-off-by: Eric Paris <eparis@redhat.com>
fanotify is going to need to look at file->private_data to know if an event
should be sent or not. This passes the data (which might be a file,
dentry, inode, or none) to the should_send function calls so fanotify can
get that information when available
Signed-off-by: Eric Paris <eparis@redhat.com>
fanotify is only interested in event types which contain enough information
to open the original file in the context of the fanotify listener. Since
fanotify may not want to send events if that data isn't present we pass
the data type to the should_send_event function call so fanotify can express
its lack of interest.
Signed-off-by: Eric Paris <eparis@redhat.com>
Simply switch audit_trees from using inotify to using fsnotify for it's
inode pinning and disappearing act information.
Signed-off-by: Eric Paris <eparis@redhat.com>
This patch allows a task to add a second fsnotify mark to an inode for the
same group. This mark will be added to the end of the inode's list and
this will never be found by the stand fsnotify_find_mark() function. This
is useful if a user wants to add a new mark before removing the old one.
Signed-off-by: Eric Paris <eparis@redhat.com>
Simple copy fsnotify information from one mark to another in preparation
for the second mark to replace the first.
Signed-off-by: Eric Paris <eparis@redhat.com>
Audit currently uses inotify to pin inodes in core and to detect when
watched inodes are deleted or unmounted. This patch uses fsnotify instead
of inotify.
Signed-off-by: Eric Paris <eparis@redhat.com>
Add a new kernel API to attach a task to current task's cgroup
in all the active hierarchies.
Signed-off-by: Sridhar Samudrala <sri@us.ibm.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Paul Menage <menage@google.com>
Acked-by: Li Zefan <lizf@cn.fujitsu.com>
This patch add DMA drivers for DMA controllers in Langwell chipset
of Intel(R) Moorestown platform and DMA controllers in Penwell of
Intel(R) Medfield platfrom
This patch adds support for Moorestown DMAC1 and DMAC2 controllers.
It also add support for Medfiled GP DMA and DMAC1 controllers.
These controllers supports memory to peripheral and peripheral to
memory transfers. It support only single block transfers.
This driver is based on Kernel DMA engine
Anyone who wishes to use this controller should use DMA engine APIs
This controller exposes DMA_SLAVE capabilities and notifies the client drivers
of DMA transaction completion
Config option required to be enabled CONFIG_INTEL_MID_DMAC=y
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
This patch adds support for RX and TX DMA via the DMA API,
this is only supported when the KS8842 is accessed via timberdale.
There is no support for DMA on the generic bus interface it self,
a state machine inside the FPGA is handling RX and TX transfers to/from
buffers in the FPGA. The host CPU can do DMA to and from these buffers.
The FPGA has to handle the RX interrupts, so these must be enabled in
the ks8842 but not in the FPGA. The driver must not disable the RX interrupt
that would mean that the data transfers into the FPGA buffers would stop.
The host shall not enable TX interrupts since TX is handled by the FPGA,
the host is notified by DMA callbacks when transfers are finished.
Which DMA channels to use are added as parameters in the platform data struct.
Signed-off-by: Richard Röjfors <richard.rojfors@pelagicore.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
s2io: fixing DBG_PRINT() macro
ath9k: fix dma direction for map/unmap in ath_rx_tasklet
net: dev_forward_skb should call nf_reset
net sched: fix race in mirred device removal
tun: avoid BUG, dump packet on GSO errors
bonding: set device in RLB ARP packet handler
wimax/i2400m: Add PID & VID for Intel WiMAX 6250
ipv6: Don't add routes to ipv6 disabled interfaces.
net: Fix skb_copy_expand() handling of ->csum_start
net: Fix corruption of skb csum field in pskb_expand_head() of net/core/skbuff.c
macvtap: Limit packet queue length
ixgbe/igb: catch invalid VF settings
bnx2x: Advance a module version
bnx2x: Protect statistics ramrod and sequence number
bnx2x: Protect a SM state change
wireless: use netif_rx_ni in ieee80211_send_layer2_update
Filesystems with unwritten extent support must not complete an AIO request
until the transaction to convert the extent has been commited. That means
the aio_complete calls needs to be moved into the ->end_io callback so
that the filesystem can control when to call it exactly.
This makes a bit of a mess out of dio_complete and the ->end_io callback
prototype even more complicated.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
__GFP_NOFAIL is going away, so add our own retry loop. Also add
jbd2__journal_start() and jbd2__journal_restart() which take a gfp
mask, so that file systems can optionally (re)start transaction
handles using GFP_KERNEL. If they do this, then they need to be
prepared to handle receiving an PTR_ERR(-ENOMEM) error, and be ready
to reflect that error up to userspace.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
To properly handle clocksources that change frequencies
at the clocksource->enable() point, this patch adds
a method that will update the clocksource's mult/shift and
max_idle_ns values.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-12-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch makes xtime and wall_to_monotonic static, as planned in
Documentation/feature-removal-schedule.txt. This will allow for
further cleanups to the timekeeping core.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-10-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Provides an accessor function to replace hrtimer.c's
direct access of wall_to_monotonic.
This will allow wall_to_monotonic to be made static as
planned in Documentation/feature-removal-schedule.txt
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-9-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
update_vsyscall() did not provide the wall_to_monotoinc offset,
so arch specific implementations tend to reference wall_to_monotonic
directly. This limits future cleanups in the timekeeping core, so
this patch fixes the update_vsyscall interface to provide
wall_to_monotonic, allowing wall_to_monotonic to be made static
as planned in Documentation/feature-removal-schedule.txt
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tony Luck <tony.luck@intel.com>
LKML-Reference: <1279068988-21864-7-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
After accidentally misusing timespec_add_safe, I wanted to make sure
we don't accidently trip over that issue again, so I created a simple
timespec_add() function which we can use to replace the instances
of timespec_add_safe() that don't want the overflow detection.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-3-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Implementation of the ST-Ericsson baudrate extension in the PL011
block. In this modified variant it is possible to change the
sampling factor from 16 to 8, and thanks to this we can get higher
baudrates while still using the same peripheral clock.
Also replace the simple division to determine the baud divisor
with DIV_ROUND_CLOSEST() rather than a simple integer division.
Cc: Alessandro Rubini <rubini@unipv.it>
Cc: Jerzy Kasenberg <jerzy.kasenberg@tieto.com>
Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
In the ST-Ericsson version of the PL011 the TX and RX have different
control registers.
Cc: Alessandro Rubini <rubini@unipv.it>
Signed-off-by: Marcin Mielczarczyk <marcin.mielczarczyk@tieto.com>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Filesystems with unwritten extent support must not complete an AIO request
until the transaction to convert the extent has been commited. That means
the aio_complete calls needs to be moved into the ->end_io callback so
that the filesystem can control when to call it exactly.
This makes a bit of a mess out of dio_complete and the ->end_io callback
prototype even more complicated.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Alex Elder <aelder@sgi.com>
This patch allows exporting GPIO pins not used by the keypad itself
to be accessible from elsewhere.
Signed-off-by: Xiaolong Chen <xiao-long.chen@motorola.com>
Signed-off-by: Yuanbo Ye <yuan-bo.ye@motorola.com>
Signed-off-by: Tao Hu <taohu@motorola.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This inserts sanity check that refuses to mount a filesystem with
unsupported block size.
Previously, kernel code of nilfs was looking only limitation of
devices though mkfs.nilfs2 limits the range of block sizes; there was
no check that prevents rec_len overflow with larger block sizes.
With this change, block sizes larger than 64KB or smaller than 1KB
will get rejected explicitly by kernel.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
With 64KB blocksize, a directory entry can have size 64KB which does
not fit into 16 bits we have for entry length. So this patch stores
0xffff instead and converts value when read from / written to disk.
Nilfs derives its directory implementation from ext2 filesystem, and
this draws upon the corresponding change on ext2.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Move frags[] at the end of struct skb_shared_info, and make
pskb_expand_head() copy only the used part of it instead of whole array.
This should avoid kmemcheck warnings and speedup pskb_expand_head() as
well, avoiding a lot of cache misses.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add addr_assign_type to struct net_device and expose it via sysfs.
This new attribute has the purpose of giving user-space the ability to
distinguish between different assignment types of MAC addresses.
For example user-space can treat NICs with randomly generated MAC
addresses differently than NICs that have permanent (locally assigned)
MAC addresses.
For the former udev could write a persistent net rule by matching the
device path instead of the MAC address.
There's also the case of devices that 'steal' MAC addresses from slave
devices. In which it is also be beneficial for user-space to be aware
of the fact.
This patch also introduces a helper function to assist adoption of
drivers that generate MAC addresses randomly.
Signed-off-by: Stefan Assmann <sassmann@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 2a6b69765a
(ACPI: Store NVS state even when entering suspend to RAM) caused the
ACPI suspend code save the NVS area during suspend and restore it
during resume unconditionally, although it is known that some systems
need to use acpi_sleep=s4_nonvs for hibernation to work. To allow
the affected systems to avoid saving and restoring the NVS area
during suspend to RAM and resume, introduce kernel command line
option acpi_sleep=nonvs and make acpi_sleep=s4_nonvs work as its
alias temporarily (add acpi_sleep=s4_nonvs to the feature removal
file).
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16396 .
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reported-and-tested-by: tomas m <tmezzadra@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
This list used was by only two platforms with all other platforms defining an
own list of valid bus id's to pass to of_platform_bus_probe. This patch:
i) copies the default list to the two platforms that depended on it (powerpc)
ii) remove the usage of of_default_bus_ids in of_platform_bus_probe
iii) removes the definition of the list from all architectures that defined it
Passing a NULL 'matches' parameter to of_platform_bus_probe is still valid; the
function returns no error in that case as the NULL value is equivalent to an
empty list.
Signed-off-by: Jonas Bonn <jonas@southpole.se>
[grant.likely@secretlab.ca: added __initdata annotations, warn on and return error on missing match table, and fix whitespace errors]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
of_device is currently just an #define alias to platform_device until it
gets removed entirely. This patch removes references to it from the
include directories and the core drivers/of code.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
It is mostly unused now. Sparc has a few defines left in it, but they
can be moved to other headers. Removing this header means that new
architectures adding CONFIG_OF support don't need to also add this
header file.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Only thing left in it is of_instantiate_rtc() which can be moved to
asm/prom.h on PowerPC and is unused in microblaze.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Both of_bus_type and of_platform_bus_type are just #define aliases
for the platform bus. This patch removes all references to them and
switches to the of_register_platform_driver()/of_unregister_platform_driver()
API for registering.
Subsequent patches will convert each user of of_register_platform_driver()
into plain platform_drivers without the of_platform_driver shim. At which
point the of_register_platform_driver()/of_unregister_platform_driver()
functions can be removed.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
of_platform_bus was being used in the same manner as the platform_bus.
The only difference being that of_platform_bus devices are generated
from data in the device tree, and platform_bus devices are usually
statically allocated in platform code. Having them separate causes
the problem of device drivers having to be registered twice if it
was possible for the same device to appear on either bus.
This patch removes of_platform_bus_type and registers all of_platform
bus devices and drivers on the platform bus instead. A previous patch
made the of_device structure an alias for the platform_device structure,
and a shim is used to adapt of_platform_drivers to the platform bus.
After all of of_platform_bus drivers are converted to be normal platform
drivers, the shim code can be removed.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
usleep[_range] are finer precision implementations of msleep
and are designed to be drop-in replacements for udelay where
a precise sleep / busy-wait is unnecessary. They also allow
an easy interface to specify slack when a precise (ish)
wakeup is unnecessary to help minimize wakeups
Signed-off-by: Patrick Pannuto <ppannuto@codeaurora.org>
Cc: akinobu.mita@gmail.com
Cc: sboyd@codeaurora.org
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
LKML-Reference: <4C44CDD2.1070708@codeaurora.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We should copy the initial value to userspace for iptables-save and
to allow removal of specific quota rules.
Signed-off-by: Changli Gao <xiaosuo@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
In both the ieee1394 stack and the firewire stack, the core treats
kernelspace drivers better than userspace drivers when it comes to
CSR address range allocation: The former may request a register to be
placed automatically at a free spot anywhere inside a specified address
range. The latter may only request a register at a fixed offset.
Hence, userspace drivers which do not require a fixed offset potentially
need to implement a retry loop with incremented offset in each retry
until the kernel does not fail allocation with EBUSY. This awkward
procedure is not fundamentally necessary as the core already provides a
superior allocation API to kernelspace drivers.
Therefore change the ioctl() ABI by addition of a region_end member in
the existing struct fw_cdev_allocate. Userspace and kernelspace APIs
work the same way now.
There is a small cost to pay by clients though: If client source code
is required to compile with older kernel headers too, then any use of
the new member fw_cdev_allocate.region_end needs to be enclosed by
#ifdef/#endif directives. However, any client program that seriously
wants to use address range allocations will require a kernel of cdev ABI
version >= 4 at runtime and a linux/firewire-cdev.h header of >= 4
anyway. This is because v4 brings FW_CDEV_EVENT_REQUEST2. The only
client program in which build-time compatibility with struct
fw_cdev_allocate as found in older kernel headers makes sense is
libraw1394.
(libraw1394 uses the older broken FW_CDEV_EVENT_REQUEST to implement a
makeshift, incorrect transaction responder that does at least work
somewhat in many simple scenarios, relying on guesswork by libraw1394
and by libraw1394 based applications. Plus, address range allocation
and transaction responder is only one of many features that libraw1394
needs to provide, and these other features need to work with kernel and
kernel-headers as old as possible. Any new linux/firewire-cdev.h based
client that implements a transaction responder should never attempt to
do it like libraw1394; instead it should make a header and kernel of v4
or later a hard requirement.)
While we are at it, update the struct fw_cdev_allocate documentation to
better reflect the recent fw_cdev_event_request2 ABI addition.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This extends the FW_CDEV_IOC_SEND_PHY_PACKET ioctl() for /dev/fw* to be
useful for ping time measurements. One application for it would be gap
count optimization in userspace that is based on ping times rather than
hop count. (The latter is implemented in firewire-core itself but is
not applicable to beta PHYs that act as repeater.)
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add an FW_CDEV_IOC_RECEIVE_PHY_PACKETS ioctl() and
FW_CDEV_EVENT_PHY_PACKET_RECEIVED poll()/read() event for /dev/fw*.
This can be used to get information from remote PHYs by remote access
PHY packets.
This is also the 2nd half of the functionality (the receive part) to
support a userspace implementation of a VersaPHY transaction layer.
Safety considerations:
- PHY packets are generally broadcasts, hence some kind of elevated
privileges should be required of a process to be able to listen in
on PHY packets. This implementation assumes that a process that is
allowed to open the /dev/fw* of a local node does have this
privilege.
There was an inconclusive discussion about introducing POSIX
capabilities as a means to check for user privileges for these
kinds of operations.
Other limitations:
- PHY packet reception may be switched on by ioctl() but cannot be
switched off again. It would be trivial to provide an off switch,
but this is not worth the code. The client should simply close()
the fd then, or just ignore further events.
- For sake of simplicity of API and kernel-side implementation, no
filter per packet content is provided.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Add an FW_CDEV_IOC_SEND_PHY_PACKET ioctl() for /dev/fw* which can be
used to implement bus management related functionality in userspace.
This is also half of the functionality (the transmit part) that is
needed to support a userspace implementation of a VersaPHY transaction
layer.
Safety considerations:
- PHY packets are generally broadcasts and may have interesting
effects on PHYs and the bus, e.g. make asynchronous arbitration
impossible due to too low gap count. Hence some kind of elevated
privileges should be required of a process to be able to send
PHY packets. This implementation assumes that a process that is
allowed to open the /dev/fw* of a local node does have this
privilege.
There was an inconclusive discussion about introducing POSIX
capabilities as a means to check for user privileges for these
kinds of operations.
- The kernel does not check integrity of the supplied packet data.
That would be far too much code, considering the many kinds of
PHY packets. A process which got the privilege to send these
packets is trusted to do it correctly.
Just like with the other "send packet" ioctls, a non-blocking API is
chosen; i.e. the ioctl may return even before AT DMA started. After
transmission, an event for poll()/read() is enqueued. Most users are
going to need a blocking API, but a blocking userspace wrapper is easy
to implement, and the second of the two existing libraw1394 calls
raw1394_phy_packet_write() and raw1394_start_phy_packet_write() can be
better supported that way.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Response events:
- are generated on more occasions than their documentation claimed.
CSR allocation:
- An already occupied CSR can be determined from errno==EBUSY.
Bus resets:
- Note that FW_CDEV_IOC_INITIATE_BUS_RESET is nonblocking and that the
client is not required to observe a grace period since kernels
2.6.36+ will enforce it now (commit 02d37bed).
- The possible values of fw_cdev_initiate_bus_reset.type are listed in
the kerneldoc comment already.
- Clarify that an application that uses FW_CDEV_IOC_ADD_DESCRIPTOR and
FW_CDEV_IOC_REMOVE_DESCRIPTOR does not have to issue a bus reset.
Isochronous I/O contexts:
- At most one can be created per open file descriptor.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
core-transaction.c transmit_complete_callback() and close_transaction()
expect packet callback status to be an ACK or RCODE, and ACKs get
translated to RCODEs for transaction callbacks.
An old comment on the packet callback API (been there from the initial
submission of the stack) and the dummy_driver implementation of
send_request/send_response deviated from this as they also included
-ERRNO in the range of status values.
Let's narrow status values down to ACK and RCODE to prevent surprises.
RCODE_CANCELLED is chosen as the dummy_driver's RCODE as its meaning of
"transaction timed out" comes closest to what happens when a transaction
coincides with card removal.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
In some situations a CPU match permits a better spreading of
connections, or select targets only for a given cpu.
With Remote Packet Steering or multiqueue NIC and appropriate IRQ
affinities, we can distribute trafic on available cpus, per session.
(all RX packets for a given flow is handled by a given cpu)
Some legacy applications being not SMP friendly, one way to scale a
server is to run multiple copies of them.
Instead of randomly choosing an instance, we can use the cpu number as a
key so that softirq handler for a whole instance is running on a single
cpu, maximizing cache effects in TCP/UDP stacks.
Using NAT for example, a four ways machine might run four copies of
server application, using a separate listening port for each instance,
but still presenting an unique external port :
iptables -t nat -A PREROUTING -p tcp --dport 80 -m cpu --cpu 0 \
-j REDIRECT --to-port 8080
iptables -t nat -A PREROUTING -p tcp --dport 80 -m cpu --cpu 1 \
-j REDIRECT --to-port 8081
iptables -t nat -A PREROUTING -p tcp --dport 80 -m cpu --cpu 2 \
-j REDIRECT --to-port 8082
iptables -t nat -A PREROUTING -p tcp --dport 80 -m cpu --cpu 3 \
-j REDIRECT --to-port 8083
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
Quota code never touches file data. It just modifies i_blocks + i_bytes
of inodes and inode flags of quota files. So use mark_inode_dirty_sync
instead of mark_inode_dirty.
Signed-off-by: Jan Kara <jack@suse.cz>
This implements the kernel-space side of the netfilter matcher xt_ipvs.
[ minor fixes by Simon Horman <horms@verge.net.au> ]
Signed-off-by: Hannes Eder <heder@google.com>
Signed-off-by: Simon Horman <horms@verge.net.au>
[ Patrick: added xt_ipvs.h to Kbuild ]
Signed-off-by: Patrick McHardy <kaber@trash.net>
This adds three new fields to nilfs_super_block structure, compatible
feature set, readonly-compatible feature set, and incompatible feature
set in order to prepare for future disk format modifications.
The role of these fields conforms to those of ext3 or other
filesystems. Most important flags are the incompatible feature set;
it is used to refuse to mount the filesystem which sets an
incompatible feature the kernel doesn't know about.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
This inserts comments indicating hexadecimal offset in declaration of
nilfs_super_block structure so that people can know offset of its
fields without counting from the head.
Signed-off-by: Ryusuke Konishi <konishi.ryusuke@lab.ntt.co.jp>
Add the xen pci platform device driver that is responsible
for initializing the grant table and xenbus in PV on HVM mode.
Few changes to xenbus and grant table are necessary to allow the delayed
initialization in HVM mode.
Grant table needs few additional modifications to work in HVM mode.
The Xen PCI platform device raises an irq every time an event has been
delivered to us. However these interrupts are only delivered to vcpu 0.
The Xen PCI platform interrupt handler calls xen_hvm_evtchn_do_upcall
that is a little wrapper around __xen_evtchn_do_upcall, the traditional
Xen upcall handler, the very same used with traditional PV guests.
When running on HVM the event channel upcall is never called while in
progress because it is a normal Linux irq handler (and we cannot switch
the irq chip wholesale to the Xen PV ones as we are running QEMU and
might have passed in PCI devices), therefore we cannot be sure that
evtchn_upcall_pending is 0 when returning.
For this reason if evtchn_upcall_pending is set by Xen we need to loop
again on the event channels set pending otherwise we might loose some
event channel deliveries.
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Signed-off-by: Sheng Yang <sheng@linux.intel.com>
Signed-off-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Make fscache operation to use only workqueue instead of combination of
workqueue and slow-work. FSCACHE_OP_SLOW is dropped and
FSCACHE_OP_FAST is renamed to FSCACHE_OP_ASYNC and uses newly added
fscache_op_wq workqueue to execute op->processor().
fscache_operation_init_slow() is dropped and fscache_operation_init()
now takes @processor argument directly.
* Unbound workqueue is used.
* fscache_retrieval_work() is no longer necessary as OP_ASYNC now does
the equivalent thing.
* sysctl fscache.operation_max_active added to control concurrency.
The default value is nr_cpus clamped between 2 and
WQ_UNBOUND_MAX_ACTIVE.
* debugfs support is dropped for now. Tracing API based debug
facility is planned to be added.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Howells <dhowells@redhat.com>
Make fscache object state transition callbacks use workqueue instead
of slow-work. New dedicated unbound CPU workqueue fscache_object_wq
is created. get/put callbacks are renamed and modified to take
@object and called directly from the enqueue wrapper and the work
function. While at it, make all open coded instances of get/put to
use fscache_get/put_object().
* Unbound workqueue is used.
* work_busy() output is printed instead of slow-work flags in object
debugging outputs. They mean basically the same thing bit-for-bit.
* sysctl fscache.object_max_active added to control concurrency. The
default value is nr_cpus clamped between 4 and
WQ_UNBOUND_MAX_ACTIVE.
* slow_work_sleep_till_thread_needed() is replaced with fscache
private implementation fscache_object_sleep_till_congested() which
waits on fscache_object_wq congestion.
* debugfs support is dropped for now. Tracing API based debug
facility is planned to be added.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: David Howells <dhowells@redhat.com>
Add a new rt attribute, RTA_MARK, and use it in
rt_fill_info()/inet_rtm_getroute() to support following commands :
ip route get 192.168.20.110 mark NUMBER
ip route get 192.168.20.108 from 192.168.20.110 iif eth1 mark NUMBER
ip route list cache [192.168.20.110] mark NUMBER
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once a work starts execution, its data contains the cpu number it was
on instead of pointing to cwq. This is added by commit 7a22ad75
(workqueue: carry cpu number in work data once execution starts) to
reliably determine the work was last on even if the workqueue itself
was destroyed inbetween.
Whether data points to a cwq or contains a cpu number was
distinguished by comparing the value against PAGE_OFFSET. The
assumption was that a cpu number should be below PAGE_OFFSET while a
pointer to cwq should be above it. However, on architectures which
use separate address spaces for user and kernel spaces, this doesn't
hold as PAGE_OFFSET is zero.
Fix it by using an explicit flag, WORK_STRUCT_CWQ, to mark what the
data field contains. If the flag is set, it's pointing to a cwq;
otherwise, it contains a cpu number.
Reported on s390 and microblaze during linux-next testing.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Sachin Sant <sachinp@in.ibm.com>
Reported-by: Michal Simek <michal.simek@petalogix.com>
Reported-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Tested-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Tested-by: Michal Simek <monstr@monstr.eu>
Mark Wagner reported OOM symptoms when sending UDP traffic over
a macvtap link to a kvm receiver.
This appears to be caused by the fact that macvtap packet queues
are unlimited in length. This means that if the receiver can't
keep up with the rate of flow, then we will hit OOM. Of course
it gets worse if the OOM killer then decides to kill the receiver.
This patch imposes a cap on the packet queue length, in the same
way as the tuntap driver, using the device TX queue length.
Please note that macvtap currently has no way of giving congestion
notification, that means the software device TX queue cannot be
used and packets will always be dropped once the macvtap driver
queue fills up.
This shouldn't be a great problem for the scenario where macvtap
is used to feed a kvm receiver, as the traffic is most likely
external in origin so congestion notification can't be applied
anyway.
Of course, if anybody decides to complain about guest-to-guest
UDP packet loss down the track, then we may have to revisit this.
Incidentally, this patch also fixes a real memory leak when
macvtap_get_queue fails.
Chris Wright noticed that for this patch to work, we need a
non-zero TX queue length. This patch includes his work to change
the default macvtap TX queue length to 500.
Reported-by: Mark Wagner <mwagner@redhat.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Chris Wright <chrisw@sous-sol.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jwessel/linux-2.6-kgdb:
sysrq,kdb: Use __handle_sysrq() for kdb's sysrq function
debug_core,kdb: fix kgdb_connected bit set in the wrong place
Fix merge regression from external kdb to upstream kdb
repair gdbstub to match the gdbserial protocol specification
kdb: break out of kdb_ll() when command is terminated
This core is found on some Freescale SoCs and also some Coldfire
SoCs. Support for Coldfire is missing though at the moment as
they have an older revision of the core which does not have RX FIFO
support.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
The kdb code should not toggle the sysrq state in case an end user
wants to try and resume the normal kernel execution.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Add more details to the dynamic function tracing design implementation.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
LKML-Reference: <1279610015-10250-1-git-send-email-vapier@gentoo.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
The current quota error message doesn't always print the disk name, so
it is hard to identify the "bad" disk when quota error happens.
This patch changes the standardized quota error message to print out disk name
and function name. It also uses a combination of cpp macro and inline function
to provide better type checking and to lower the text size of the message.
[Jan Kara: Export __quota_error]
Signed-off-by: Jiaying Zhang <jiayingz@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
The nobh option was only supported for writeback mode, but given that all
write paths (except mmapped writed) actually create buffer heads, it
effectively was a no-op already.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
The various quota operations check for any quota beeing active on
a superblock, and the inode not having the noquota flag.
Merge these two checks into a dquot_active check and move that
into dquot.c as that's the only place where it's needed.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Almost all identifiers use the FS_* namespace, so rename the missing few
XFS_* ones to FS_* as well. Without this some people might get upset
about having too many XFS names in generic code.
Acked-by: Steven Whitehouse <swhiteho@redhat.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
__print_flags() and __print_symbolic() use percpu trace_seq:
1) Its memory is allocated at compile time, it wastes memory if we don't use tracing.
2) It is percpu data and it wastes more memory for multi-cpus system.
3) It disables preemption when it executes its core routine
"trace_seq_printf(s, "%s: ", #call);" and introduces latency.
So we move this trace_seq to struct trace_iterator.
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
LKML-Reference: <4C078350.7090106@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
We found that even enabling a single trace event that will rarely be
triggered can add big overhead to context switch.
(lmbench context switch test)
-------------------------------------------------
2p/0K 2p/16K 2p/64K 8p/16K 8p/64K 16p/16K 16p/64K
ctxsw ctxsw ctxsw ctxsw ctxsw ctxsw ctxsw
------ ------ ------ ------ ------ ------- -------
2.19 2.3 2.21 2.56 2.13 2.54 2.07
2.39 2.51 2.35 2.75 2.27 2.81 2.24
The overhead is 6% ~ 11%.
It's because when a trace event is enabled 3 tracepoints (sched_switch,
sched_wakeup, sched_wakeup_new) will be activated to map pid to cmdname.
We'd like to avoid this overhead, so add a trace option '(no)record-cmd'
to allow to disable cmdline recording.
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4C2D57F4.2050204@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/r600: fix possible NULL pointer derefernce
drm/radeon/kms: add quirk for ASUS HD 3600 board
include/linux/vgaarb.h: add missing part of include guard
drm/nouveau: Fix crashes during fbcon init on single head cards.
drm/nouveau: fix pcirom vbios shadow breakage from acpi rom patch
drm/radeon/kms: fix shared ddc harder
drm/i915: enable low power render writes on GEN3 hardware.
drm/i915: Define MI_ARB_STATE bits
vmwgfx: return -EFAULT if copy_to_user fails
fb: handle allocation failure in alloc_apertures()
drm: radeon: check kzalloc() result
drm/ttm: Fix build on architectures without AGP
drm/radeon/kms: fix gtt MC base alignment on rs4xx/rs690/rs740 asics
drm/radeon/kms: fix possible mis-detection of sideport on rs690/rs740
drm/radeon/kms: fix legacy tv-out pal mode
vgaarb.h was missing the #define of the #ifndef at the top for the guard
to prevent multiple #include's from causing re-define errors
Signed-off-by: Doug Goldstein <cardoe@gentoo.org>
Cc: Dave Airlie <airlied@redhat.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
If a single-threaded process does a file-descriptor operation, and some
other process accesses that same file descriptor via /proc, the current
rcu_dereference_check_fdtable() can give a false-positive RCU-lockdep
splat due to the reference count being increased by the /proc access after
the reference-count check in fget_light() but before the check in
rcu_dereference_check_fdtable().
This commit prevents this false positive by checking for a single-threaded
process. To avoid #include hell, this commit uses the wrapper for
thread_group_empty(current) defined by rcu_my_thread_group_empty()
provided in a separate commit.
Located-by: Miles Lane <miles.lane@gmail.com>
Located-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Al Viro <viro@ZenIV.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Special traces type was only used by sysprof. Lets remove it now
that sysprof ftrace plugin has been dropped.
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Acked-by: Soeren Sandmann <sandmann@daimi.au.dk>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Li Zefan <lizf@cn.fujitsu.com>
If the kzalloc() fails we should return NULL. All the places that call
alloc_apertures() check for this already.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: James Simmons <jsimmons@infradead.org>
Acked-by: Marcin Slusarz <marcin.slusarz@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Even with jumbograms I cannot see any way in which we would need
to records a larger than 65535 valued next-header offset.
The maximum extension header length is (256 << 3) == 2048.
There are only a handful of extension headers specified which
we'd even accept (say 5 or 6), therefore the largest next-header
offset we'd ever have to contend with is something less than
say 16k.
Therefore make it a u16 instead of a u32.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since struct netdev_queue tx_bytes/tx_packets/tx_dropped are already
protected by _xmit_lock, its easy to convert these fields to u64 instead
of unsigned long.
This completes 64bit stats for devices using them (vlan, macvlan, ...)
Strictly, we could avoid the locking in dev_txq_stats_fold() on 64bit
arches, but its slow path and we prefer keep it simple.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch allows IOMMU users to determine whether the
hardware and software support safe, isolated interrupt
remapping. Not all Intel IOMMUs have the hardware, and the
software for AMD is not there yet.
Signed-off-by: Tom Lyon <pugs@cisco.com>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
For devices with exotic HID report descriptors, it might be necessary to
make the HID core force the registration of an input device. Make that
possible by introducing a new quirk type.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Added sysfs primitives to padata subsystem. Now API user may
embedded kobject each padata instance contains into any sysfs
hierarchy. For now padata sysfs interface provides only
two objects:
serial_cpumask [RW] - cpumask for serial workers
parallel_cpumask [RW] - cpumask for parallel workers
Signed-off-by: Dan Kruchinin <dkruchinin@acm.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The aim of this patch is to make two separate cpumasks
for padata parallel and serial workers respectively.
It allows user to make more thin and sophisticated configurations
of padata framework. For example user may bind parallel and serial workers to non-intersecting
CPU groups to gain better performance. Also each padata instance has notifiers chain for its
cpumasks now. If either parallel or serial or both masks were changed all
interested subsystems will get notification about that. It's especially useful
if padata user uses algorithm for callback CPU selection according to serial cpumask.
Signed-off-by: Dan Kruchinin <dkruchinin@acm.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
The current shrinker implementation requires the registered callback
to have global state to work from. This makes it difficult to shrink
caches that are not global (e.g. per-filesystem caches). Pass the shrinker
structure to the callback so that users can embed the shrinker structure
in the context the shrinker needs to operate on and get back to it in the
callback via container_of().
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
This patch adds a new networking option to allow hardware time stamps
from PHY devices. When enabled, likely candidates among incoming and
outgoing network packets are offered to the PHY driver for possible
time stamping. When accepted by the PHY driver, incoming packets are
deferred for later delivery by the driver.
The patch also adds phylib driver methods for the SIOCSHWTSTAMP ioctl
and callbacks for transmit and receive time stamping. Drivers may
optionally implement these functions.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
Certain kinds of hardware time stamping units in both MACs and PHYs have
the limitation that they can only time stamp PTP packets. Drivers for such
hardware are left with the task of correctly matching skbs to time stamps.
This patch adds a BPF that drivers can use to classify PTP packets when
needed.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy_mii_ioctl() function unnecessarily throws away the original ifreq.
We need access to the ifreq in order to support PHYs that can perform
hardware time stamping.
Two maverick drivers filter the ioctl commands passed to phy_mii_ioctl().
This is unnecessary since phylib will check the command in any case.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a hook for transmit time stamps. The transmit hook
allows a software fallback for transmit time stamps, for MACs
lacking time stamping hardware. Using the hook will still require
adding an inline function call to each MAC driver.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order for PowerTOP to be able to report how well the new runtime PM is
working for the various drivers, the kernel needs to export some basic
statistics in sysfs.
This patch adds two sysfs files in the runtime PM domain that expose the
total time a device has been active, and the time a device has been
suspended.
With this PowerTOP can compute the activity percentage
Active %age = 100 * (delta active) / (delta active + delta suspended)
and present the information to the user.
I've written the PowerTOP code (slated for version 1.12) already, and the
output looks like this:
Runtime Device Power Management statistics
Active Device name
10.0% 06:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8101E/RTL8102E PCI Express Fast Ethernet controller
[version 2: fix stat update bugs noticed by Alan Stern]
[version 3: rebase to -next and move the sysfs declaration]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The ACPI suspend code calls suspend_nvs_free() at a wrong place,
which may lead to a memory leak if there's an error executing
acpi_pm_prepare(), because acpi_pm_finish() will not be called in
that case. However, the root cause of this problem is the
apparently confusing ordering of calls in suspend error paths that
needs to be fixed.
In addition to that, fix a typo in a label name in suspend.c.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Len Brown <len.brown@intel.com>
All current users of pm_qos_add_request() have the ability to supply
the memory required by the pm_qos routines, so make them do this and
eliminate the kmalloc() with pm_qos_add_request(). This has the
double benefit of making the call never fail and allowing it to be
called from atomic context.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: mark gross <markgross@thegnar.org>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
plist is currently used by the scheduler, which only needs to know the
highest item in the list. This adds plist_last which allows you to
find the lowest. This is necessary for using plists to implement a
fast search of dynamic ranges in pm_qos which can have both highest
and lowest criteria.
Signed-off-by: James Bottomley <James.Bottomley@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
One of the arguments during the suspend blockers discussion was that
the mainline kernel didn't contain any mechanisms making it possible
to avoid races between wakeup and system suspend.
Generally, there are two problems in that area. First, if a wakeup
event occurs exactly when /sys/power/state is being written to, it
may be delivered to user space right before the freezer kicks in, so
the user space consumer of the event may not be able to process it
before the system is suspended. Second, if a wakeup event occurs
after user space has been frozen, it is not generally guaranteed that
the ongoing transition of the system into a sleep state will be
aborted.
To address these issues introduce a new global sysfs attribute,
/sys/power/wakeup_count, associated with a running counter of wakeup
events and three helper functions, pm_stay_awake(), pm_relax(), and
pm_wakeup_event(), that may be used by kernel subsystems to control
the behavior of this attribute and to request the PM core to abort
system transitions into a sleep state already in progress.
The /sys/power/wakeup_count file may be read from or written to by
user space. Reads will always succeed (unless interrupted by a
signal) and return the current value of the wakeup events counter.
Writes, however, will only succeed if the written number is equal to
the current value of the wakeup events counter. If a write is
successful, it will cause the kernel to save the current value of the
wakeup events counter and to abort the subsequent system transition
into a sleep state if any wakeup events are reported after the write
has returned.
[The assumption is that before writing to /sys/power/state user space
will first read from /sys/power/wakeup_count. Next, user space
consumers of wakeup events will have a chance to acknowledge or
veto the upcoming system transition to a sleep state. Finally, if
the transition is allowed to proceed, /sys/power/wakeup_count will
be written to and if that succeeds, /sys/power/state will be written
to as well. Still, if any wakeup events are reported to the PM core
by kernel subsystems after that point, the transition will be
aborted.]
Additionally, put a wakeup events counter into struct dev_pm_info and
make these per-device wakeup event counters available via sysfs,
so that it's possible to check the activity of various wakeup event
sources within the kernel.
To illustrate how subsystems can use pm_wakeup_event(), make the
low-level PCI runtime PM wakeup-handling code use it.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: markgross <markgross@thegnar.org>
Reviewed-by: Alan Stern <stern@rowland.harvard.edu>
This patch (as1354) adds remote-wakeup support to the pnpacpi driver.
The new can_wakeup method also allows other PNP protocol drivers
(pnpbios or iaspnp) to add wakeup support, but I don't know enough
about how they work to actually do it.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reviewed-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This patch (as1381b) updates a comment describing the kernel's policy
toward enabling wakeup by default.
It also makes device_set_wakeup_capable() actually do something when
CONFIG_PM isn't enabled. It's not clear this is necessary; however if
it isn't then device_init_wakeup() and device_can_wakeup() should also
be do-nothing routines. Furthermore, I don't expect this change to
have any noticeable effect -- but if it does then clearly the old
behavior was wrong.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jlbec/ocfs2:
ocfs2: Silence gcc warning in ocfs2_write_zero_page().
jbd2/ocfs2: Fix block checksumming when a buffer is used in several transactions
ocfs2/dlm: Remove BUG_ON from migration in the rare case of a down node
ocfs2: Don't duplicate pages past i_size during CoW.
ocfs2: tighten up strlen() checking
ocfs2: Make xattr reflink work with new local alloc reservation.
ocfs2: make xattr extension work with new local alloc reservation.
ocfs2: Remove the redundant cpu_to_le64.
ocfs2/dlm: don't access beyond bitmap size
ocfs2: No need to zero pages past i_size.
ocfs2: Zero the tail cluster when extending past i_size.
ocfs2: When zero extending, do it by page.
ocfs2: Limit default local alloc size within bitmap range.
ocfs2: Move orphan scan work to ocfs2_wq.
fs/ocfs2/dlm: Add missing spin_unlock
Norbert reported that nohz_ratelimit() causes his laptop to burn about
4W (40%) extra. For now back out the change and see if we can adjust
the power management code to make better decisions.
Reported-by: Norbert Preining <preining@logic.at>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mike Galbraith <efault@gmx.de>
Cc: Arjan van de Ven <arjan@infradead.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This moves the various known Marvell PHY IDs to include/linux/marvell_phy.h
along with dev_flags definitions for use by the driver.
I then added a flag that changes the PHY init code to setup the LEDs
config to the values needed to operate a dns323 rev C1 NAS.
I moved the existing "resistance" flag to the .h as well, though I've
been unable to find whoever sets this to convert it to use that constant.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
If we fail to assign resources to a PCI BAR, this patch makes us try the
original address from BIOS rather than leaving it disabled.
Linux tries to make sure all PCI device BARs are inside the upstream
PCI host bridge or P2P bridge apertures, reassigning BARs if necessary.
Windows does similar reassignment.
Before this patch, if we could not move a BAR into an aperture, we left
the resource unassigned, i.e., at address zero. Windows leaves such BARs
at the original BIOS addresses, and this patch makes Linux do the same.
This is a bit ugly because we disable the resource long before we try to
reassign it, so we have to keep track of the BIOS BAR address somewhere.
For lack of a better place, I put it in the struct pci_dev.
I think it would be cleaner to attempt the assignment immediately when the
claim fails, so we could easily remember the original address. But we
currently claim motherboard resources in the middle, after attempting to
claim PCI resources and before assigning new PCI resources, and changing
that is a fairly big job.
Addresses https://bugzilla.kernel.org/show_bug.cgi?id=16263
Reported-by: Andrew <nitr0@seti.kr.ua>
Tested-by: Andrew <nitr0@seti.kr.ua>
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
* 'perf-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
tracing: Add alignment to syscall metadata declarations
perf: Sync callchains with period based hits
perf: Resurrect flat callchains
perf: Version String fix, for fallback if not from git
perf: Version String fix, using kernel version
The cacheline with the flags is reachable from the hot paths after the
percpu allocator changes went in. So there is no need anymore to put a
flag into each slab page. Get rid of the SlubDebug flag and use
the flags in kmem_cache instead.
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Christoph Lameter <cl@linux-foundation.org>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
This patch adds the code to support the sys_prlimit64 syscall which
modifies-and-returns the rlim values of a selected process atomically.
The first parameter, pid, being 0 means current process.
Unlike the current implementation, it is a generic interface,
architecture indepentent so that we needn't handle compat stuff
anymore. In the future, after glibc start to use this we can deprecate
sys_setrlimit and sys_getrlimit in favor to clean up the code finally.
It also adds a possibility of changing limits of other processes. We
check the user's permissions to do that and if it succeeds, the new
limits are propagated online. This is good for large scale
applications such as SAP or databases where administrators need to
change limits time by time (e.g. on crashes increase core size). And
it is unacceptable to restart the service.
For safety, all rlim users now either use accessors or doesn't need
them due to
- locking
- the fact a process was just forked and nobody else knows about it
yet (and nobody can't thus read/write limits)
hence it is safe to modify limits now.
The limitation is that we currently stay at ulong internal
representation. So the rlim64_is_infinity check is used where value is
compared against ULONG_MAX on 32-bit which is the maximum value there.
And since internally the limits are held in struct rlimit, converters
which are used before and after do_prlimit call in sys_prlimit64 are
introduced.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
It now allows also reading of limits. I.e. all read and writes will
later use this function.
It takes two parameters, new and old limits which can be both NULL.
If new is non-NULL, the value in it is set to rlimits.
If old is non-NULL, current rlimits are stored there.
If both are non-NULL, old are stored prior to setting the new ones,
atomically.
(Similar to sigaction.)
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Add a platform independent structure for resource limits to use with
a new prlimit64 syscall. This structure is the same which uses glibc
for 64-bit limits.
Also add corresponding infinity which is a 64-bit full of bit-ones.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Create do_setrlimit from sys_setrlimit and declare do_setrlimit
in the resource header. This is the first phase to have generic
do_prlimit which allows to be called from read, write and compat
rlimits code.
The new do_setrlimit also accepts a task pointer to change the limits
of. Currently, it cannot be other than current, but this will change
with locking later.
Also pass tsk->group_leader to security_task_setrlimit to check
whether current is allowed to change rlimits of the process and not
its arbitrary thread because it makes more sense given that rlimit are
per process and not per-thread.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Add task_struct as a parameter to update_rlimit_cpu to be able to set
rlimit_cpu of different task than current.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: James Morris <jmorris@namei.org>
Add task_struct to task_setrlimit of security_operations to be able to set
rlimit of task other than current.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Acked-by: Eric Paris <eparis@redhat.com>
Acked-by: James Morris <jmorris@namei.org>
With the rapidly increasing number of intelligent multi-contact and
multi-user devices, the need to send digested, filtered information
from a set of different sources within the same device is imminent.
This patch adds the concept of slots to the MT protocol. The slots
enumerate a set of identified sources, such that all MT events
can be passed independently and selectively per identified source.
The protocol works like this: Instead of sending a SYN_MT_REPORT
event immediately after the contact data, one sends an ABS_MT_SLOT
event immediately before the contact data. The input core will only
emit events for slots with modified MT events. It is assumed that
the same slot is used for the duration of an initiated contact.
Acked-by: Ping Cheng <pingc@wacom.com>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Acked-by: Rafi Rubin <rafi@seas.upenn.edu>
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
OCFS2 uses t_commit trigger to compute and store checksum of the just
committed blocks. When a buffer has b_frozen_data, checksum is computed
for it instead of b_data but this can result in an old checksum being
written to the filesystem in the following scenario:
1) transaction1 is opened
2) handle1 is opened
3) journal_access(handle1, bh)
- This sets jh->b_transaction to transaction1
4) modify(bh)
5) journal_dirty(handle1, bh)
6) handle1 is closed
7) start committing transaction1, opening transaction2
8) handle2 is opened
9) journal_access(handle2, bh)
- This copies off b_frozen_data to make it safe for transaction1 to commit.
jh->b_next_transaction is set to transaction2.
10) jbd2_journal_write_metadata() checksums b_frozen_data
11) the journal correctly writes b_frozen_data to the disk journal
12) handle2 is closed
- There was no dirty call for the bh on handle2, so it is never queued for
any more journal operation
13) Checkpointing finally happens, and it just spools the bh via normal buffer
writeback. This will write b_data, which was never triggered on and thus
contains a wrong (old) checksum.
This patch fixes the problem by calling the trigger at the moment data is
frozen for journal commit - i.e., either when b_frozen_data is created by
do_get_write_access or just before we write a buffer to the log if
b_frozen_data does not exist. We also rename the trigger to t_frozen as
that better describes when it is called.
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mark Fasheh <mfasheh@suse.com>
Signed-off-by: Joel Becker <joel.becker@oracle.com>
This adds a `CHECKSUM' target, which can be used in the iptables mangle
table.
You can use this target to compute and fill in the checksum in
a packet that lacks a checksum. This is particularly useful,
if you need to work around old applications such as dhcp clients,
that do not work well with checksum offloads, but don't want to
disable checksum offload in your device.
The problem happens in the field with virtualized applications.
For reference, see Red Hat bz 605555, as well as
http://www.spinics.net/lists/kvm/msg37660.html
Typical expected use (helps old dhclient binary running in a VM):
iptables -A POSTROUTING -t mangle -p udp --dport bootpc \
-j CHECKSUM --checksum-fill
Includes fixes by Jan Engelhardt <jengelh@medozas.de>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Patrick McHardy <kaber@trash.net>
This patch moves NFULNL_COPY_PACKET definition from
linux/netfilter/nfnetlink_log.h to net/netfilter/nfnetlink_log.h
since this copy mode is only for internal use.
I have also changed the value from 0x03 to 0xff. Thus, we avoid
a gap from user-space that may confuse users if we add new
copy modes in the future.
This change was introduced in:
http://www.spinics.net/lists/netfilter-devel/msg13535.html
Since this change is not included in any stable Linux kernel,
I think it's safe to make this change now. Anyway, this copy
mode does not make any sense from user-space, so this patch
should not break any existing setup.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The chip's full name is AT42QT602240 or ATMXT224. This is a capacitive
touchscreen supporting 10-contact multitouch and using I2C interface.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Acked-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Rename is_root_node() to of_node_is_root() and make it available for
all archs to use, as it's not PROM-specific.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
We count the number of processed objects on a percpu basis,
so we need to go through all the percpu reorder queues to calculate
the sequence number of the next object that needs serialization.
This patch changes this to count the number of processed objects
global. So we can calculate the sequence number and the percpu
reorder queue of the next object that needs serialization without
searching through the percpu reorder queues. This avoids some
accesses to memory of foreign cpus.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
This patch introduces the PADATA_INVALID flag which is
checked on padata start. This will be used to mark a padata
instance as invalid, if the padata cpumask does not intersect
with the active cpumask. we change padata_start to return an
error if the PADATA_INVALID is set. Also we adapt the only
padata user, pcrypt to this change.
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
via following scripts
FILES=$(find * -type f | grep -vE 'oprofile|[^K]config')
sed -i \
-e 's/lmb/memblock/g' \
-e 's/LMB/MEMBLOCK/g' \
$FILES
for N in $(find . -name lmb.[ch]); do
M=$(echo $N | sed 's/lmb/memblock/g')
mv $N $M
done
and remove some wrong change like lmbench and dlmb etc.
also move memblock.c from lib/ to mm/
Suggested-by: Ingo Molnar <mingo@elte.hu>
Acked-by: "H. Peter Anvin" <hpa@zytor.com>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Bus resets which are triggered
- by the kernel drivers after updates of the local nodes' config ROM,
- by userspace software via ioctl
shall be deferred until after >=2 seconds after the last bus reset.
If multiple modifications of the local nodes' config ROM happen in a row,
only a single bus reset should happen after them.
When the local node's link goes from inactive to active or vice versa,
and at the two occasions of bus resets mentioned above --- and if the
current gap count differs from 63 --- the bus reset should be preceded
by a PHY configuration packet that reaffirms the gap count. Otherwise a
bus manager would have to reset the bus again right after that.
This is necessary to promote bus stability, e.g. leave grace periods for
allocations and reallocations of isochronous channels and bandwidth,
SBP-2 reconnections etc.; see IEEE 1394 clause 8.2.1.
This change implements all of the above by moving bus reset initiation
into a delayed work (except for bus resets which are triggered by the
bus manager workqueue job and are performed there immediately). It
comes with a necessary addition to the card driver methods that allows
to get the current gap count from PHY registers.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Userspace filesystem can request data to be retrieved from the inode's
mapping. This request is synchronous and the retrieved data is queued
as a new request. If the write to the fuse device returns an error
then the retrieve request was not completed and a reply will not be
sent.
Only present pages are returned in the retrieve reply. Retrieving
stops when it finds a non-present page and only data prior to that is
returned.
This request doesn't change the dirty state of pages.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Userspace filesystem can request data to be stored in the inode's
mapping. This request is synchronous and has no reply. If the write
to the fuse device returns an error then the store request was not
fully completed (but may have updated some pages).
If the stored data overflows the current file size, then the size is
extended, similarly to a write(2) on the filesystem.
Pages which have been completely stored are marked uptodate.
Signed-off-by: Miklos Szeredi <mszeredi@suse.cz>
Move the preprocessor #warning message:
warning: #warning Attempt to use kernel headers from user space,
see http://kernelnewbies.org/KernelHeaders
from kernel.h to types.h.
And also fixe the #warning message due to the preprocessor not being able to
read the web address due to it thinking it was the start of a comment. also
remove the extra #ifndef _KERNEL_ since it's already there.
Signed-off-by: Justin P. Mattock <justinmattock@gmail.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Document that dev_get_stats() returns the same stats pointer it was
given. Remove const qualification from the returned pointer since the
caller may do what it likes with that structure.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit be1f3c2c02 "net: Enable 64-bit
net device statistics on 32-bit architectures" I redefined struct
net_device_stats so that it could be used in a union with struct
rtnl_link_stats64, avoiding the need for explicit copying or
conversion between the two. However, this is unsafe because there is
no locking required and no lock consistently held around calls to
dev_get_stats() and use of the statistics structure it returns.
In commit 28172739f0 "net: fix 64 bit
counters on 32 bit arches" Eric Dumazet dealt with that problem by
requiring callers of dev_get_stats() to provide storage for the
result. This means that the net_device::stats64 field and the padding
in struct net_device_stats are now redundant, so remove them.
Update the comment on net_device_ops::ndo_get_stats64 to reflect its
new usage.
Change dev_txq_stats_fold() to use struct rtnl_link_stats64, since
that is what all its callers are really using and it is no longer
going to be compatible with struct net_device_stats.
Eric Dumazet suggested the separate function for the structure
conversion.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For some reason if we declare a static variable and then assign it
later, and the assignment contains a __attribute__((__aligned__(#))),
some versions of gcc will ignore it.
This caused the syscall meta data to not be compact in its section
and caused a kernel oops when the section was being read.
The fix for these versions of gcc seems to be to add the aligned
attribute to the declaration as well.
This fixes the BZ regression:
https://bugzilla.kernel.org/show_bug.cgi?id=16353
Reported-by: Zeev Tarantov <zeev.tarantov@gmail.com>
Tested-by: Zeev Tarantov <zeev.tarantov@gmail.com>
Acked-by: Frederic Weisbecker <fweisbec@gmail.com>
LKML-Reference: <AANLkTinkKVmB0fpVeqUkMeqe3ZYeXJdI8xDuzJEOjYwh@mail.gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Current x86 ioremap() doesn't handle physical address higher than
32-bit properly in X86_32 PAE mode. When physical address higher than
32-bit is passed to ioremap(), higher 32-bits in physical address is
cleared wrongly. Due to this bug, ioremap() can map wrong address to
linear address space.
In my case, 64-bit MMIO region was assigned to a PCI device (ioat
device) on my system. Because of the ioremap()'s bug, wrong physical
address (instead of MMIO region) was mapped to linear address space.
Because of this, loading ioatdma driver caused unexpected behavior
(kernel panic, kernel hangup, ...).
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
LKML-Reference: <4C1AE680.7090408@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Add notifier chain for changes in atm_dev.
Clients like br2684 will call register_atmdevice_notifier() to be notified of
changes. Drivers will call atm_dev_signal_change() to notify clients like
br2684 of the change.
On DSL and ATM devices it's usefull to have a know if you have a carrier
signal. netdevice LOWER_UP changes can be propagated to userspace via netlink
monitor.
Signed-off-by: Karl Hiramoto <karl@hiramoto.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
writeback: simplify the write back thread queue
writeback: split writeback_inodes_wb
writeback: remove writeback_inodes_wbc
fs-writeback: fix kernel-doc warnings
splice: check f_mode for seekable file
splice: direct_splice_actor() should not use pos in sd
Fix an obscure ABI feature that is a bit of a hassle to implement.
However, somebody put it into the ABI, so let's fill in a sensible
value there.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (35 commits)
NET: SB1250: Initialize .owner
vxge: show startup message with KERN_INFO
ll_temac: Fix missing iounmaps
bridge: Clear IPCB before possible entry into IP stack
bridge br_multicast: BUG: unable to handle kernel NULL pointer dereference
net: Fix definition of netif_vdbg() when VERBOSE_DEBUG is defined
net/ne: fix memory leak in ne_drv_probe()
xfrm: fix xfrm by MARK logic
virtio_net: fix oom handling on tx
virtio_net: do not reschedule rx refill forever
s2io: resolve statistics issues
linux/net.h: fix kernel-doc warnings
net: decreasing real_num_tx_queues needs to flush qdisc
sched: qdisc_reset_all_tx is calling qdisc_reset without qdisc_lock
qlge: fix a eeh handler to not add a pending timer
qlge: Replacing add_timer() to mod_timer()
usbnet: Set parent device early for netdev_printk()
net: Revert "rndis_host: Poll status channel before control channel"
netfilter: ip6t_REJECT: fix a dst leak in ipv6 REJECT
drivers: bluetooth: bluecard_cs.c: Fixed include error, changed to linux/io.h
...
There is a small possibility that a reader gets incorrect values on 32
bit arches. SNMP applications could catch incorrect counters when a
32bit high part is changed by another stats consumer/provider.
One way to solve this is to add a rtnl_link_stats64 param to all
ndo_get_stats64() methods, and also add such a parameter to
dev_get_stats().
Rule is that we are not allowed to use dev->stats64 as a temporary
storage for 64bit stats, but a caller provided area (usually on stack)
Old drivers (only providing get_stats() method) need no changes.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch introduces 3 VFS accessors: 'sb_mark_dirty()',
'sb_mark_clean()', and 'sb_is_dirty()'. They simply
set 'sb->s_dirt' or test 'sb->s_dirt'. The plan is to make
every FS use these accessors later instead of manipulating
the 'sb->s_dirt' flag directly.
Ultimately, this change is a preparation for the periodic
superblock synchronization optimization which is about
preventing the "sync_supers" kernel thread from waking up
even if there is nothing to synchronize.
This patch does not do any functional change, just adds
accessor functions.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rbtree: Undo augmented trees performance damage and regression
x86, Calgary: Limit the max PHB number to 256
This allows a list_head (or hlist_head, etc.) to be used from places
that used to be impractical, in particular <asm/processor.h>, which
used to cause include file recursion: <linux/list.h> includes
<linux/prefetch.h>, which always includes <asm/processor.h> for the
prefetch macros, as well as <asm/system.h>, which often includes
<asm/processor.h> directly or indirectly.
This avoids a lot of painful workaround hackery on the tile
architecture, where we use a list_head in the thread_struct to chain
together tasks that are activated on a particular hardwall.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Reviewed-by: Matthew Wilcox <willy@linux.intel.com>
This patch makes the cache_cleaner workqueue deferrable, to prevent
unnecessary system wake-ups, which is very important for embedded
battery-powered devices.
do_cache_clean() is called every 30 seconds at the moment, and often
makes the system wake up from its power-save sleep state. With this
change, when the workqueue uses a deferrable timer, the
do_cache_clean() invocation will be delayed and combined with the
closest "real" wake-up. This improves the power consumption situation.
Note, I tried to create a DECLARE_DELAYED_WORK_DEFERRABLE() helper
macro, similar to DECLARE_DELAYED_WORK(), but failed because of the
way the timer wheel core stores the deferrable flag (it is the
LSBit in the time->base pointer). My attempt to define a static
variable with this bit set ended up with the "initializer element is
not constant" error.
Thus, I have to use run-time initialization, so I created a new
cache_initialize() function which is called once when sunrpc is
being initialized.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
First remove items from work_list as soon as we start working on them. This
means we don't have to track any pending or visited state and can get
rid of all the RCU magic freeing the work items - we can simply free
them once the operation has finished. Second use a real completion for
tracking synchronous requests - if the caller sets the completion pointer
we complete it, otherwise use it as a boolean indicator that we can free
the work item directly. Third unify struct wb_writeback_args and struct
bdi_work into a single data structure, wb_writeback_work. Previous we
set all parameters into a struct wb_writeback_args, copied it into
struct bdi_work, copied it again on the stack to use it there. Instead
of just allocate one structure dynamically or on the stack and use it
all the way through the stack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
The case where we have a superblock doesn't require a loop here as we scan
over all inodes in writeback_sb_inodes. Split it out into a separate helper
to make the code simpler. This also allows to get rid of the sb member in
struct writeback_control, which was rather out of place there.
Also update the comments in writeback_sb_inodes that explain the handling
of inodes from wrong superblocks.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
This was just an odd wrapper around writeback_inodes_wb. Removing this
also allows to get rid of the bdi member of struct writeback_control
which was rather out of place there.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
netif_vdbg() was originally defined as entirely equivalent to
netdev_vdbg(), but I assume that it was intended to take the same
parameters as netif_dbg() etc. (Currently it is only used by the
sfc driver, in which I worked on that assumption.)
In commit a4ed89c I changed the definition used when VERBOSE_DEBUG is
not defined, but I failed to notice that the definition used when
VERBOSE_DEBUG is defined was also not as I expected. Change that to
match netif_dbg() as well.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch cleans up the i2c OF support code to make it selectable by
all architectures and allow for automatic registration of i2c devices.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Some code uses of_device even when CONFIG_OF_DEVICE is not set. This
patch makes of_device valid all the time by moving it outside of the
ifdef CONFIG_OF_DEVICE test.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Add of_driver_match_device() helper function. This function can be used
by bus types to determine if a driver works with a device when using OF
style matching. If CONFIG_OF is unselected, then it is a nop.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CC: Greg Kroah-Hartman <gregkh@suse.de>
CC: Michal Simek <monstr@monstr.eu>
CC: Grant Likely <grant.likely@secretlab.ca>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
CC: linux-kernel@vger.kernel.org
CC: microblaze-uclinux@itee.uq.edu.au
CC: linuxppc-dev@ozlabs.org
CC: devicetree-discuss@lists.ozlabs.org
Implement generic OF gpio hooks and thus make device-enabled GPIO chips
(i.e. the ones that have gpio_chip->dev specified) automatically attach
to the OpenFirmware subsystem. Which means that now we can handle I2C and
SPI GPIO chips almost* transparently.
* "Almost" because some chips still require platform data, and for these
chips OF-glue is still needed, though with this change the glue will
be much smaller.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bill Gatliff <bgat@billgatliff.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
CC: linux-kernel@vger.kernel.org
CC: devicetree-discuss@lists.ozlabs.org
Currently the kernel uses the struct device_node.data pointer to resolve
a struct gpio_chip pointer from a device tree node. However, the .data
member doesn't provide any type checking and there aren't any rules
enforced on what it should be used for. There's no guarantee that the
data stored in it actually points to an gpio_chip pointer.
Instead of relying on the .data pointer, this patch modifies the code
to add a lookup function which scans through the registered gpio_chips
and returns the gpio_chip that has a pointer to the specified
device_node.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CC: Andrew Morton <akpm@linux-foundation.org>
CC: Anton Vorontsov <avorontsov@ru.mvista.com>
CC: Grant Likely <grant.likely@secretlab.ca>
CC: David Brownell <dbrownell@users.sourceforge.net>
CC: Bill Gatliff <bgat@billgatliff.com>
CC: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Jean Delvare <khali@linux-fr.org>
CC: linux-kernel@vger.kernel.org
CC: devicetree-discuss@lists.ozlabs.org
The OF gpio infrastructure is great for describing GPIO connections within
the device tree. However, using a GPIO binding still requires changes to
the gpio controller just to add an of_gpio structure. In most cases, the
gpio controller doesn't actually need any special support and the simple
OF gpio mapping function is more than sufficient. Additional, the current
scheme of using of_gpio_chip requires a convoluted scheme to maintain
1:1 mappings between of_gpio_chip and gpio_chip instances.
If the struct of_gpio_chip data members were moved into struct gpio_chip,
then it would simplify the processing of OF gpio bindings, and it would
make it trivial to use device tree OF connections on existing gpiolib
controller drivers.
This patch eliminates the of_gpio_chip structure and moves the relevant
fields into struct gpio_chip (conditional on CONFIG_OF_GPIO). This move
simplifies the existing code and prepares for adding automatic device tree
support to existing drivers.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Bill Gatliff <bgat@billgatliff.com>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Jean Delvare <khali@linux-fr.org>
This patch merges the common routines of_device_alloc() and
of_device_make_bus_id() from powerpc and microblaze.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CC: Michal Simek <monstr@monstr.eu>
CC: Grant Likely <grant.likely@secretlab.ca>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
CC: microblaze-uclinux@itee.uq.edu.au
CC: linuxppc-dev@ozlabs.org
CC: devicetree-discuss@lists.ozlabs.org
Merge common code between PowerPC and microblaze. This patch merges
the code that scans the tree and registers devices. The functions
merged are of_platform_bus_probe(), of_platform_bus_create(), and
of_platform_device_create().
This patch also move the of_default_bus_ids[] table out of a Microblaze
header file and makes it non-static. The device ids table isn't merged
because powerpc and microblaze use different default data.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CC: Michal Simek <monstr@monstr.eu>
CC: Grant Likely <grant.likely@secretlab.ca>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
CC: microblaze-uclinux@itee.uq.edu.au
CC: linuxppc-dev@ozlabs.org
Now that the of_node pointer is part of struct device,
of_device_get_modalias could be used on any struct device
that has the device node pointer set. This patch changes
of_device_get_modalias to accept a struct device instead
of a struct of_device.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CC: Michal Simek <monstr@monstr.eu>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Wolfram Sang <w.sang@pengutronix.de>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
CC: microblaze-uclinux@itee.uq.edu.au
CC: linuxppc-dev@ozlabs.org
Merge common code between powerpc and microblaze
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CC: Michal Simek <monstr@monstr.eu>
CC: Wolfram Sang <w.sang@pengutronix.de>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: microblaze-uclinux@itee.uq.edu.au
CC: linuxppc-dev@ozlabs.org
Microblaze and PowerPC share a large chunk of code for translating
OF device tree data into usable addresses. Differences between the two
consist of cosmetic differences, and the addition of dma-ranges support
code to powerpc but not microblaze. This patch moves the powerpc
version into common code and applies many of the cosmetic (non-functional)
changes from the microblaze version.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Michal Simek <monstr@monstr.eu>
CC: Wolfram Sang <w.sang@pengutronix.de>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
Merge common code between PowerPC and Microblaze. This patch also
moves the prototype of pci_address_to_pio() out of pci-bridge.h and
into prom.h because the only user of pci_address_to_pio() is
of_address_to_resource().
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Michal Simek <monstr@monstr.eu>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
Merge common code between Microblaze and PowerPC. This patch creates
new of_address.h and address.c files to containing address translation
and mapping routines. First routine to be moved it of_iomap()
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Michal Simek <monstr@monstr.eu>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
Merge common irq mapping code between PowerPC and Microblaze.
This patch merges of_irq_find_parent(), of_irq_map_raw() and
of_irq_map_one(). The functions are dependent on one another, so all
three are merged in a single patch. Other than cosmetic difference
(ie. DBG() vs. pr_debug()), the implementations are identical.
of_irq_to_resource() is also merged, but in this case the
implementations are different. This patch drops the microblaze version
and uses the powerpc implementation unchanged. The microblaze version
essentially open-coded irq_of_parse_and_map() which it does not need
to do. Therefore the powerpc version is safe to adopt.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
CC: Michal Simek <monstr@monstr.eu>
CC: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: Stephen Rothwell <sfr@canb.auug.org.au>
Reimplement augmented RB-trees without sprinkling extra branches
all over the RB-tree code (which lives in the scheduler hot path).
This approach is 'borrowed' from Fabio's BFQ implementation and
relies on traversing the rebalance path after the RB-tree-op to
correct the heap property for insertion/removal and make up for
the damage done by the tree rotations.
For insertion the rebalance path is trivially that from the new
node upwards to the root, for removal it is that from the deepest
node in the path from the to be removed node that will still
be around after the removal.
[ This patch also fixes a video driver regression reported by
Ali Gholami Rudi - the memtype->subtree_max_end was updated
incorrectly. ]
Acked-by: Suresh Siddha <suresh.b.siddha@intel.com>
Acked-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Tested-by: Ali Gholami Rudi <ali@rudi.ir>
Cc: Fabio Checconi <fabio@gandalf.sssup.it>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <1275414172.27810.27961.camel@twins>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
We should initialize the module dynamic debug datastructures
only after determining that the module is not loaded yet. This
fixes a bug that introduced in 2.6.35-rc2, where when a trying
to load a module twice, we also load it's dynamic printing data
twice which causes all sorts of nasty issues. Also handle
the dynamic debug cleanup later on failure.
Signed-off-by: Yehuda Sadeh <yehuda@hq.newdream.net>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au> (removed a #ifdef)
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Reduces text ~300 bytes of text (woohoo!) in an x86 defconfig
$ size vmlinux*
text data bss dec hex filename
7198526 720112 1366288 9284926 8dad3e vmlinux
7198862 720112 1366288 9285262 8dae8e vmlinux.netdev
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduces an x86 defconfig text and data ~2k.
text is smaller, data is larger.
$ size vmlinux*
text data bss dec hex filename
7198862 720112 1366288 9285262 8dae8e vmlinux
7205273 716016 1366288 9287577 8db799 vmlinux.device_h
Uses %pV and struct va_format
Format arguments are verified before printk
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reduces an x86 defconfig text and data ~55k, .6% smaller.
$ size vmlinux*
text data bss dec hex filename
7205273 716016 1366288 9287577 8db799 vmlinux
7258890 719768 1366288 9344946 8e97b2 vmlinux.master
Uses %pV and struct va_format
Format arguments are verified before printk
The dev_info macro is converted to _dev_info because there are
existing uses of variables named dev_info in the kernel tree
like drivers/net/pcmcia/pcnet_cs.c
A dev_info macro is created to call _dev_info
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ability to print a format and va_list from a structure pointer
Allows __dev_printk to be implemented as a single printk while
minimizing string space duplication.
%pV should not be used without some mechanism to verify the
format and argument use ala __attribute__(format (printf(...))).
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
In slab, all __xxx_track_caller is defined on CONFIG_DEBUG_SLAB || CONFIG_TRACING,
thus caller tracking function should be worked for CONFIG_TRACING. But if
CONFIG_DEBUG_SLAB is not set, include/linux/slab.h will define xxx_track_caller to
__xxx() without consideration of CONFIG_TRACING. This will break the caller tracking
behaviour then.
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Dmitry Monakhov <dmonakhov@openvz.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
Fix kernel-doc warnings in linux/net.h:
Warning(include/linux/net.h:151): No description found for parameter 'wq'
Warning(include/linux/net.h:151): Excess struct/union/enum/typedef member 'fasync_list' description in 'socket'
Warning(include/linux/net.h:151): Excess struct/union/enum/typedef member 'wait' description in 'socket'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reducing real_num_queues needs to flush the qdisc otherwise
skbs with queue_mappings greater then real_num_tx_queues can
be sent to the underlying driver.
The flow for this is,
dev_queue_xmit()
dev_pick_tx()
skb_tx_hash() => hash using real_num_tx_queues
skb_set_queue_mapping()
...
qdisc_enqueue_root() => enqueue skb on txq from hash
...
dev->real_num_tx_queues -= n
...
sch_direct_xmit()
dev_hard_start_xmit()
ndo_start_xmit(skb,dev) => skb queue set with old hash
skbs are enqueued on the qdisc with skb->queue_mapping set
0 < queue_mappings < real_num_tx_queues. When the driver
decreases real_num_tx_queues skb's may be dequeued from the
qdisc with a queue_mapping greater then real_num_tx_queues.
This fixes a case in ixgbe where this was occurring with DCB
and FCoE. Because the driver is using queue_mapping to map
skbs to tx descriptor rings we can potentially map skbs to
rings that no longer exist.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WQ_SINGLE_CPU combined with @max_active of 1 is used to achieve full
ordering among works queued to a workqueue. The same can be achieved
using WQ_UNBOUND as unbound workqueues always use the gcwq for
WORK_CPU_UNBOUND. As @max_active is always one and benefits from cpu
locality isn't accessible anyway, serving them with unbound workqueues
should be fine.
Drop WQ_SINGLE_CPU support and use WQ_UNBOUND instead. Note that most
single thread workqueue users will be converted to use multithread or
non-reentrant instead and only the ones which require strict ordering
will keep using WQ_UNBOUND + @max_active of 1.
Signed-off-by: Tejun Heo <tj@kernel.org>
This patch implements unbound workqueue which can be specified with
WQ_UNBOUND flag on creation. An unbound workqueue has the following
properties.
* It uses a dedicated gcwq with a pseudo CPU number WORK_CPU_UNBOUND.
This gcwq is always online and disassociated.
* Workers are not bound to any CPU and not concurrency managed. Works
are dispatched to workers as soon as possible and the only applied
limitation is @max_active. IOW, all unbound workqeueues are
implicitly high priority.
Unbound workqueues can be used as simple execution context provider.
Contexts unbound to any cpu are served as soon as possible.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Cc: David Howells <dhowells@redhat.com>
In preparation of WQ_UNBOUND addition, make the following changes.
* Add WORK_CPU_* constants for pseudo cpu id numbers used (currently
only WORK_CPU_NONE) and use them instead of NR_CPUS. This is to
allow another pseudo cpu id for unbound cpu.
* Reorder WQ_* flags.
* Make workqueue_struct->cpu_wq a union which contains a percpu
pointer, regular pointer and an unsigned long value and use
kzalloc/kfree() in UP allocation path. This will be used to
implement unbound workqueues which will use only one cwq on SMPs.
* Move alloc_cwqs() allocation after initialization of wq fields, so
that alloc_cwqs() has access to wq->flags.
* Trivial relocation of wq local variables in freeze functions.
These changes don't cause any functional change.
Signed-off-by: Tejun Heo <tj@kernel.org>
libata has two concurrency related limitations.
a. ata_wq which is used for polling PIO has single thread per CPU. If
there are multiple devices doing polling PIO on the same CPU, they
can't be executed simultaneously.
b. ata_aux_wq which is used for SCSI probing has single thread. In
cases where SCSI probing is stalled for extended period of time
which is possible for ATAPI devices, this will stall all probing.
#a is solved by increasing maximum concurrency of ata_wq. Please note
that polling PIO might be used under allocation path and thus needs to
be served by a separate wq with a rescuer.
#b is solved by using the default wq instead and achieving exclusion
via per-port mutex.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Jeff Garzik <jgarzik@pobox.com>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev:
ata_generic: implement ATA_GEN_* flags and force enable DMA on MBP 7,1
ahci,ata_generic: let ata_generic handle new MBP w/ MCP89
libahci: Fix bug in storing EM messages
For yet unknown reason, MCP89 on MBP 7,1 doesn't work w/ ahci under
linux but the controller doesn't require explicit mode setting and
works fine with ata_generic. Make ahci ignore the controller on MBP
7,1 and let ata_generic take it for now.
Reported in bko#15923.
https://bugzilla.kernel.org/show_bug.cgi?id=15923
NVIDIA is investigating why ahci mode doesn't work.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Peer Chen <pchen@nvidia.com>
Cc: stable@kernel.org
Reported-by: Anders Østhus <grapz666@gmail.com>
Reported-by: Andreas Graf <andreas_graf@csgraf.de>
Reported-by: Benoit Gschwind <gschwind@gnu-log.net>
Reported-by: Damien Cassou <damien.cassou@gmail.com>
Reported-by: tixetsal@juno.com
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (27 commits)
drm/radeon/kms: remove rv100 bios connector quirk
drm/radeon/kms/pm: fix power state indexing on igp chips in dynpm mode
DRM / radeon / KMS: Fix hibernation regression related to radeon PM (was: Re: [Regression, post-2.6.34] Hibernation broken on machines with radeon/KMS and r300)
drm/radeon/kms/igp: fix possible divide by 0 in bandwidth code (v2)
drm/radeon: add quirk to make HP nx6125 laptop resume.
drm/radeon/kms: add some missing regs to evergreen gpu init
drm/radeon/kms: fix typos in evergreen command checker
drm/radeon/kms: avoid oops on mac r4xx cards
fb: fix colliding defines for fb flags.
drm/radeon/kms: Force HDP_NONSURF to maximum size
drm/radeon/kms: disable frac fb dividers for rs6xx
drm/radeon/kms: don't read attempt to read bios from VRAM on unposted GPU.
drm/radeon/kms: fix typo in evergreen_gpu_init
drm/radeon/kms: return ret in cursor_set failure path
drm/ttm: non pooled page allocation should have GFP_USER set
drm/radeon/r100/r200: fix calculation of compressed cube maps
drm/radeon/r200: handle more hw tex coord types
drm/radeon/kms: CS checker texture fixes for r1xx/r2xx/r3xx
drm/radeon: add fake RN50 table for powerpc
drm/fb: Fix video= mode computation
...
Commit 0224cf4c5e (sched: Intoduce get_cpu_iowait_time_us())
broke things by not making sure preemption was indeed disabled
by the callers of nr_iowait_cpu() which took the iowait value of
the current cpu.
This resulted in a heap of preempt warnings. Cure this by making
nr_iowait_cpu() take a cpu number and fix up the callers to pass
in the right number.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-pm@lists.linux-foundation.org
LKML-Reference: <1277968037.1868.120.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Conflicts:
fs/fs-writeback.c
Merge reason: Resolve the conflict
Note, i picked the version from Linus's tree, which effectively reverts
the fs-writeback.c bits of:
b97181f: fs: remove all rcu head initializations, except on_stack initializations
As the upstream changes to this file changed this code heavily and the
first attempt to resolve the conflict resulted in a non-booting kernel.
It's safer to re-try this portion of the commit cleanly.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
When I added the flags I must have been using a 25 line terminal and missed the following flags.
The collided with flag has one user in staging despite being in-tree for 5 years.
I'm happy to push this via my drm tree unless someone really wants to do it.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cc: stable@kernel.org
Many NICs use an indirection table to map an RX flow hash value to one
of an arbitrary number of queues (not necessarily a power of 2). It
can be useful to remove some queues from this indirection table so
that they are only used for flows that are specifically filtered
there. It may also be useful to weight the mapping to account for
user processes with the same CPU-affinity as the RX interrupts.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ethtool_op_set_flags() does not check for unsupported flags, and has
no way of doing so. This means it is not suitable for use as a
default implementation of ethtool_ops::set_flags.
Add a 'supported' parameter specifying the flags that the driver and
hardware support, validate the requested flags against this, and
change all current callers to pass this parameter.
Change some other trivial implementations of ethtool_ops::set_flags to
call ethtool_op_set_flags().
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Reviewed-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some controllers (KW, Dove) limits the TX IP/layer4 checksum offloading to a max size.
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Acked-by: Lennert Buytenhek <buytenh@wantstofly.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Gertjan van Wingerde <gwingerde@gmail.com>
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Otherwise we may run into following:
drivers/platform/built-in.o: In function `i8042_lock_chip':
/home/test/ws2/projects/linux-2.6/include/linux/i8042.h:50: multiple definition of `i8042_lock_chip'
drivers/input/serio/built-in.o:/home/test/ws2/projects/linux-2.6/include/linux/i8042.h:50: first defined here
...
make[1]: *** [drivers/built-in.o] Error 1
make: *** [drivers] Error 2
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
A __naked function is defined in C but with a body completely implemented
by asm(), including any prologue and epilogue. These asm() bodies expect
standard calling conventions for parameter passing. Older GCCs implement
that correctly, but 4.[56] currently do not, see GCC PR44290. In the
Linux kernel this breaks ARM, causing most arch/arm/mm/copypage-*.c
modules to get miscompiled, resulting in kernel crashes during bootup.
Part of the kernel fix is to augment the __naked function attribute to
also imply noinline and noclone. This patch implements that, and has been
verified to fix boot failures with gcc-4.5 compiled 2.6.34 and 2.6.35-rc1
kernels. The patch is a no-op with older GCCs.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Khem Raj <raj.khem@gmail.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.dk/linux-2.6-block:
block: Don't count_vm_events for discard bio in submit_bio.
cfq: fix recursive call in cfq_blkiocg_update_completion_stats()
cfq-iosched: Fixed boot warning with BLK_CGROUP=y and CFQ_GROUP_IOSCHED=n
cfq: Don't allow queue merges for queues that have no process references
block: fix DISCARD_BARRIER requests
cciss: set SCSI max cmd len to 16, as default is wrong
cpqarray: fix two more wrong section type
cpqarray: fix wrong __init type on pci probe function
drbd: Fixed a race between disk-attach and unexpected state changes
writeback: fix pin_sb_for_writeback
writeback: add missing requeue_io in writeback_inodes_wb
writeback: simplify and split bdi_start_writeback
writeback: simplify wakeup_flusher_threads
writeback: fix writeback_inodes_wb from writeback_inodes_sb
writeback: enforce s_umount locking in writeback_inodes_sb
writeback: queue work on stack in writeback_inodes_sb
writeback: fix writeback completion notifications
list_for_each_entry_safe is not suitable to protect against concurrent
modification of the list. 6754af6 introduced a race in sb walking.
list_for_each_entry can use the trick of pinning the current entry in
the list before we drop and retake the lock because it subsequently
follows cur->next. However list_for_each_entry_safe saves n=cur->next
for following before entering the loop body, so when the lock is
dropped, n may be deleted.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Frank Mayhar <fmayhar@google.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
No logic changes, only spelling.
Signed-off-by: Michael Neuling <mikey@neuling.org>
Cc: linuxppc-dev@ozlabs.org
Cc: David Howells <dhowells@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <15249.1277776921@neuling.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch implements cpu intensive workqueue which can be specified
with WQ_CPU_INTENSIVE flag on creation. Works queued to a cpu
intensive workqueue don't participate in concurrency management. IOW,
it doesn't contribute to gcwq->nr_running and thus doesn't delay
excution of other works.
Note that although cpu intensive works won't delay other works, they
can be delayed by other works. Combine with WQ_HIGHPRI to avoid being
delayed by other works too.
As the name suggests this is useful when using workqueue for cpu
intensive works. Workers executing cpu intensive works are not
considered for workqueue concurrency management and left for the
scheduler to manage.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
This patch implements high priority workqueue which can be specified
with WQ_HIGHPRI flag on creation. A high priority workqueue has the
following properties.
* A work queued to it is queued at the head of the worklist of the
respective gcwq after other highpri works, while normal works are
always appended at the end.
* As long as there are highpri works on gcwq->worklist,
[__]need_more_worker() remains %true and process_one_work() wakes up
another worker before it start executing a work.
The above two properties guarantee that works queued to high priority
workqueues are dispatched to workers and start execution as soon as
possible regardless of the state of other works.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Implement the following utility APIs.
workqueue_set_max_active() : adjust max_active of a wq
workqueue_congested() : test whether a wq is contested
work_cpu() : determine the last / current cpu of a work
work_busy() : query whether a work is busy
* Anton Blanchard fixed missing ret initialization in work_busy().
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Anton Blanchard <anton@samba.org>
This patch makes changes to make new workqueue features available to
its users.
* Now that workqueue is more featureful, there should be a public
workqueue creation function which takes paramters to control them.
Rename __create_workqueue() to alloc_workqueue() and make 0
max_active mean WQ_DFL_ACTIVE. In the long run, all
create_workqueue_*() will be converted over to alloc_workqueue().
* To further unify access interface, rename keventd_wq to system_wq
and export it.
* Add system_long_wq and system_nrt_wq. The former is to host long
running works separately (so that flush_scheduled_work() dosen't
take so long) and the latter guarantees any queued work item is
never executed in parallel by multiple CPUs. These will be used by
future patches to update workqueue users.
Signed-off-by: Tejun Heo <tj@kernel.org>
Define WQ_MAX_ACTIVE and create keventd with max_active set to half of
it which means that keventd now can process upto WQ_MAX_ACTIVE / 2 - 1
works concurrently. Unless some combination can result in dependency
loop longer than max_active, deadlock won't happen and thus it's
unnecessary to check whether current_is_keventd() before trying to
schedule a work. Kill current_is_keventd().
(Lockdep annotations are broken. We need lock_map_acquire_read_norecurse())
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Instead of creating a worker for each cwq and putting it into the
shared pool, manage per-cpu workers dynamically.
Works aren't supposed to be cpu cycle hogs and maintaining just enough
concurrency to prevent work processing from stalling due to lack of
processing context is optimal. gcwq keeps the number of concurrent
active workers to minimum but no less. As long as there's one or more
running workers on the cpu, no new worker is scheduled so that works
can be processed in batch as much as possible but when the last
running worker blocks, gcwq immediately schedules new worker so that
the cpu doesn't sit idle while there are works to be processed.
gcwq always keeps at least single idle worker around. When a new
worker is necessary and the worker is the last idle one, the worker
assumes the role of "manager" and manages the worker pool -
ie. creates another worker. Forward-progress is guaranteed by having
dedicated rescue workers for workqueues which may be necessary while
creating a new worker. When the manager is having problem creating a
new worker, mayday timer activates and rescue workers are summoned to
the cpu and execute works which might be necessary to create new
workers.
Trustee is expanded to serve the role of manager while a CPU is being
taken down and stays down. As no new works are supposed to be queued
on a dead cpu, it just needs to drain all the existing ones. Trustee
continues to try to create new workers and summon rescuers as long as
there are pending works. If the CPU is brought back up while the
trustee is still trying to drain the gcwq from the previous offlining,
the trustee will kill all idles ones and tell workers which are still
busy to rebind to the cpu, and pass control over to gcwq which assumes
the manager role as necessary.
Concurrency managed worker pool reduces the number of workers
drastically. Only workers which are necessary to keep the processing
going are created and kept. Also, it reduces cache footprint by
avoiding unnecessarily switching contexts between different workers.
Please note that this patch does not increase max_active of any
workqueue. All workqueues can still only process one work per cpu.
Signed-off-by: Tejun Heo <tj@kernel.org>
With gcwq managing all the workers and work->data pointing to the last
gcwq it was on, non-reentrance can be easily implemented by checking
whether the work is still running on the previous gcwq on queueing.
Implement it.
Signed-off-by: Tejun Heo <tj@kernel.org>
To implement non-reentrant workqueue, the last gcwq a work was
executed on must be reliably obtainable as long as the work structure
is valid even if the previous workqueue has been destroyed.
To achieve this, work->data will be overloaded to carry the last cpu
number once execution starts so that the previous gcwq can be located
reliably. This means that cwq can't be obtained from work after
execution starts but only gcwq.
Implement set_work_{cwq|cpu}(), get_work_[g]cwq() and
clear_work_data() to set work data to the cpu number when starting
execution, access the overloaded work data and clear it after
cancellation.
queue_delayed_work_on() is updated to preserve the last cpu while
in-flight in timer and other callers which depended on getting cwq
from work after execution starts are converted to depend on gcwq
instead.
* Anton Blanchard fixed compile error on powerpc due to missing
linux/threads.h include.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Anton Blanchard <anton@samba.org>
Reimplement st (single thread) workqueue so that it's friendly to
shared worker pool. It was originally implemented by confining st
workqueues to use cwq of a fixed cpu and always having a worker for
the cpu. This implementation isn't very friendly to shared worker
pool and suboptimal in that it ends up crossing cpu boundaries often.
Reimplement st workqueue using dynamic single cpu binding and
cwq->limit. WQ_SINGLE_THREAD is replaced with WQ_SINGLE_CPU. In a
single cpu workqueue, at most single cwq is bound to the wq at any
given time. Arbitration is done using atomic accesses to
wq->single_cpu when queueing a work. Once bound, the binding stays
till the workqueue is drained.
Note that the binding is never broken while a workqueue is frozen.
This is because idle cwqs may have works waiting in delayed_works
queue while frozen. On thaw, the cwq is restarted if there are any
delayed works or unbound otherwise.
When combined with max_active limit of 1, single cpu workqueue has
exactly the same execution properties as the original single thread
workqueue while allowing sharing of per-cpu workers.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reimplement CPU hotplugging support using trustee thread. On CPU
down, a trustee thread is created and each step of CPU down is
executed by the trustee and workqueue_cpu_callback() simply drives and
waits for trustee state transitions.
CPU down operation no longer waits for works to be drained but trustee
sticks around till all pending works have been completed. If CPU is
brought back up while works are still draining,
workqueue_cpu_callback() tells trustee to step down and tell workers
to rebind to the cpu.
As it's difficult to tell whether cwqs are empty if it's freezing or
frozen, trustee doesn't consider draining to be complete while a gcwq
is freezing or frozen (tracked by new GCWQ_FREEZING flag). Also,
workers which get unbound from their cpu are marked with WORKER_ROGUE.
Trustee based implementation doesn't bring any new feature at this
point but it will be used to manage worker pool when dynamic shared
worker pool is implemented.
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently, workqueue freezing is implemented by marking the worker
freezeable and calling try_to_freeze() from dispatch loop.
Reimplement it using cwq->limit so that the workqueue is frozen
instead of the worker.
* workqueue_struct->saved_max_active is added which stores the
specified max_active on initialization.
* On freeze, all cwq->max_active's are quenched to zero. Freezing is
complete when nr_active on all cwqs reach zero.
* On thaw, all cwq->max_active's are restored to wq->saved_max_active
and the worklist is repopulated.
This new implementation allows having single shared pool of workers
per cpu.
Signed-off-by: Tejun Heo <tj@kernel.org>
Add cwq->nr_active, cwq->max_active and cwq->delayed_work. nr_active
counts the number of active works per cwq. A work is active if it's
flushable (colored) and is on cwq's worklist. If nr_active reaches
max_active, new works are queued on cwq->delayed_work and activated
later as works on the cwq complete and decrement nr_active.
cwq->max_active can be specified via the new @max_active parameter to
__create_workqueue() and is set to 1 for all workqueues for now. As
each cwq has only single worker now, this double queueing doesn't
cause any behavior difference visible to its users.
This will be used to reimplement freeze/thaw and implement shared
worker pool.
Signed-off-by: Tejun Heo <tj@kernel.org>
A work is linked to the next one by having WORK_STRUCT_LINKED bit set
and these links can be chained. When a linked work is dispatched to a
worker, all linked works are dispatched to the worker's newly added
->scheduled queue and processed back-to-back.
Currently, as there's only single worker per cwq, having linked works
doesn't make any visible behavior difference. This change is to
prepare for multiple shared workers per cpu.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reimplement workqueue flushing using color coded works. wq has the
current work color which is painted on the works being issued via
cwqs. Flushing a workqueue is achieved by advancing the current work
colors of cwqs and waiting for all the works which have any of the
previous colors to drain.
Currently there are 16 possible colors, one is reserved for no color
and 15 colors are useable allowing 14 concurrent flushes. When color
space gets full, flush attempts are batched up and processed together
when color frees up, so even with many concurrent flushers, the new
implementation won't build up huge queue of flushers which has to be
processed one after another.
Only works which are queued via __queue_work() are colored. Works
which are directly put on queue using insert_work() use NO_COLOR and
don't participate in workqueue flushing. Currently only works used
for work-specific flush fall in this category.
This new implementation leaves only cleanup_workqueue_thread() as the
user of flush_cpu_workqueue(). Just make its users use
flush_workqueue() and kthread_stop() directly and kill
cleanup_workqueue_thread(). As workqueue flushing doesn't use barrier
request anymore, the comment describing the complex synchronization
around it in cleanup_workqueue_thread() is removed together with the
function.
This new implementation is to allow having and sharing multiple
workers per cpu.
Please note that one more bit is reserved for a future work flag by
this patch. This is to avoid shifting bits and updating comments
later.
Signed-off-by: Tejun Heo <tj@kernel.org>
work->data field is used for two purposes. It points to cwq it's
queued on and the lower bits are used for flags. Currently, two bits
are reserved which is always safe as 4 byte alignment is guaranteed on
every architecture. However, future changes will need more flag bits.
On SMP, the percpu allocator is capable of honoring larger alignment
(there are other users which depend on it) and larger alignment works
just fine. On UP, percpu allocator is a thin wrapper around
kzalloc/kfree() and don't honor alignment request.
This patch introduces WORK_STRUCT_FLAG_BITS and implements
alloc/free_cwqs() which guarantees max(1 << WORK_STRUCT_FLAG_BITS,
__alignof__(unsigned long long) alignment both on SMP and UP. On SMP,
simply wrapping percpu allocator is enough. On UP, extra space is
allocated so that cwq can be aligned and the original pointer can be
stored after it which is used in the free path.
* Alignment problem on UP is reported by Michal Simek.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Reported-by: Michal Simek <michal.simek@petalogix.com>
Work flags are about to see more traditional mask handling. Define
WORK_STRUCT_*_BIT as the bit position constant and redefine
WORK_STRUCT_* as bit masks. Also, make WORK_STRUCT_STATIC_* flags
conditional
While at it, re-define these constants as enums and use
WORK_STRUCT_STATIC instead of hard-coding 2 in
WORK_DATA_STATIC_INIT().
Signed-off-by: Tejun Heo <tj@kernel.org>
Currently, __create_workqueue_key() takes @singlethread and
@freezeable paramters and store them separately in workqueue_struct.
Merge them into a single flags parameter and field and use
WQ_FREEZEABLE and WQ_SINGLE_THREAD.
Signed-off-by: Tejun Heo <tj@kernel.org>
Make the following updates in preparation of concurrency managed
workqueue. None of these changes causes any visible behavior
difference.
* Add comments and adjust indentations to data structures and several
functions.
* Rename wq_per_cpu() to get_cwq() and swap the position of two
parameters for consistency. Convert a direct per_cpu_ptr() access
to wq->cpu_wq to get_cwq().
* Add work_static() and Update set_wq_data() such that it sets the
flags part to WORK_STRUCT_PENDING | WORK_STRUCT_STATIC if static |
@extra_flags.
* Move santiy check on work->entry emptiness from queue_work_on() to
__queue_work() which all queueing paths share.
* Make __queue_work() take @cpu and @wq instead of @cwq.
* Restructure flush_work() and __create_workqueue_key() to make them
easier to modify.
Signed-off-by: Tejun Heo <tj@kernel.org>
With stop_machine() converted to use cpu_stop, RT workqueue doesn't
have any user left. Kill RT workqueue support.
Signed-off-by: Tejun Heo <tj@kernel.org>
Implement kthread_data() which takes @task pointing to a kthread and
returns @data specified when creating the kthread. The caller is
responsible for ensuring the validity of @task when calling this
function.
Signed-off-by: Tejun Heo <tj@kernel.org>
Implement simple work processor for kthread. This is to ease using
kthread. Single thread workqueue used to be used for things like this
but workqueue won't guarantee fixed kthread association anymore to
enable worker sharing.
This can be used in cases where specific kthread association is
necessary, for example, when it should have RT priority or be assigned
to certain cgroup.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
struct ethtool_rxnfc was originally defined in 2.6.27 for the
ETHTOOL_{G,S}RXFH command with only the cmd, flow_type and data
fields. It was then extended in 2.6.30 to support various additional
commands. These commands should have been defined to use a new
structure, but it is too late to change that now.
Since user-space may still be using the old structure definition
for the ETHTOOL_{G,S}RXFH commands, and since they do not need the
additional fields, only copy the originally defined fields to and
from user-space.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Cc: stable@kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Use u64_stats_sync infrastructure to implement 64bit stats.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Must disable preemption in case of 32bit UP in u64_stats_fetch_begin()
and u64_stats_fetch_retry()
- Add new u64_stats_fetch_begin_bh() and u64_stats_fetch_retry_bh() for
network usage, disabling BH on 32bit UP only.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Add a comment about interrupts:
6) If counter might be written by an interrupt, readers should block
interrupts.
- Fix a typo in sample of use.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because kprobes and syscalls need special processing to register
events, the class->reg() method was created to handle the differences.
But instead of creating a default ->reg for perf and ftrace events,
the code was scattered with:
if (class->reg)
class->reg();
else
default_reg();
This is messy and can also lead to bugs.
This patch cleans up this code and creates a default reg() entry for
the events allowing for the code to directly call the class->reg()
without the condition.
Reported-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
All syscall exit events have the same fields.
The kernel size drops 2.5K:
text data bss dec hex filename
7018612 2034376 7251132 16304120 f8c7f8 vmlinux.o.orig
7018612 2031888 7251132 16301632 f8be40 vmlinux.o
Signed-off-by: Li Zefan <lizf@cn.fujitsu.com>
LKML-Reference: <4BFA3746.8070100@cn.fujitsu.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Merge common code between PowerPC and Microblaze. SPARC implements
irq_of_parse_and_map(), but the implementation is different, so it
does not use this code.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Michal Simek <monstr@monstr.eu>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Jeremy Kerr <jeremy.kerr@canonical.com>
Now that the device tree node pointer has been moved out of struct
of_device and into the common struct device, there isn't anything
unique about of_device anymore. In fact, there isn't much need
for a separate of_bus when all busses have access to OF style
probing.
arch/powerpc and arch/microblaze are moving away from using the of_bus
and using the regular platform bus instead for mmio devices. This
patch makes of_device the same as platform_device as a stepping stone
in migrating of_platform_drivers over to the platform bus.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: David S. Miller <davem@davemloft.net>
Cc: Michal Simek <monstr@monstr.eu>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
The LOG targets print the entire MAC header as one long string, which is not
readable very well:
IN=eth0 OUT= MAC=00:15:f2:24:91:f8:00:1b:24:dc:61:e6:08:00 ...
Add an option to decode known header formats (currently just ARPHRD_ETHER devices)
in their individual fields:
IN=eth0 OUT= MACSRC=00:1b:24:dc:61:e6 MACDST=00:15:f2:24:91:f8 MACPROTO=0800 ...
IN=eth0 OUT= MACSRC=00:1b:24:dc:61:e6 MACDST=00:15:f2:24:91:f8 MACPROTO=86dd ...
The option needs to be explicitly enabled by userspace to avoid breaking
existing parsers.
Signed-off-by: Patrick McHardy <kaber@trash.net>
On some platforms, for example with GPIO interrupts on mpc5121,
it is not possible to configure falling edge interrupts.
Specifying irq trigger type in platform data structure
allows using ads7846 driver on such platforms.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch updates percpu allocator such that it can serve limited
amount of allocation before slab comes online. This is primarily to
allow slab to depend on working percpu allocator.
Two parameters, PERCPU_DYNAMIC_EARLY_SIZE and SLOTS, determine how
much memory space and allocation map slots are reserved. If this
reserved area is exhausted, WARN_ON_ONCE() will trigger and allocation
will fail till slab comes online.
The following changes are made to implement early alloc.
* pcpu_mem_alloc() now checks slab_is_available()
* Chunks are allocated using pcpu_mem_alloc()
* Init paths make sure ai->dyn_size is at least as large as
PERCPU_DYNAMIC_EARLY_SIZE.
* Initial alloc maps are allocated in __initdata and copied to
kmalloc'd areas once slab is online.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Christoph Lameter <cl@linux-foundation.org>
In pcpu_build_alloc_info() and pcpu_embed_first_chunk(), @dyn_size was
ssize_t, -1 meant auto-size, 0 forced 0 and positive meant minimum
size. There's no use case for forcing 0 and the upcoming early alloc
support always requires non-zero dynamic size. Make @dyn_size always
mean minimum dyn_size.
While at it, make pcpu_build_alloc_info() static which doesn't have
any external caller as suggested by David Rientjes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: David Rientjes <rientjes@google.com>
Gcc is currenlty not in the ability to optimize the switch statement in
sk_run_filter() because of dense case labels. This patch replace the
OR'd labels with ordered sequenced case labels. The sk_chk_filter()
function is modified to patch/replace the original OPCODES in a
ordered but equivalent form. gcc is now in the ability to transform the
switch statement in sk_run_filter into a jump table of complexity O(1).
Until this patch gcc generates a sequence of conditional branches (O(n) of 567
byte .text segment size (arch x86_64):
7ff: 8b 06 mov (%rsi),%eax
801: 66 83 f8 35 cmp $0x35,%ax
805: 0f 84 d0 02 00 00 je adb <sk_run_filter+0x31d>
80b: 0f 87 07 01 00 00 ja 918 <sk_run_filter+0x15a>
811: 66 83 f8 15 cmp $0x15,%ax
815: 0f 84 c5 02 00 00 je ae0 <sk_run_filter+0x322>
81b: 77 73 ja 890 <sk_run_filter+0xd2>
81d: 66 83 f8 04 cmp $0x4,%ax
821: 0f 84 17 02 00 00 je a3e <sk_run_filter+0x280>
827: 77 29 ja 852 <sk_run_filter+0x94>
829: 66 83 f8 01 cmp $0x1,%ax
[...]
With the modification the compiler translate the switch statement into
the following jump table fragment:
7ff: 66 83 3e 2c cmpw $0x2c,(%rsi)
803: 0f 87 1f 02 00 00 ja a28 <sk_run_filter+0x26a>
809: 0f b7 06 movzwl (%rsi),%eax
80c: ff 24 c5 00 00 00 00 jmpq *0x0(,%rax,8)
813: 44 89 e3 mov %r12d,%ebx
816: e9 43 03 00 00 jmpq b5e <sk_run_filter+0x3a0>
81b: 41 89 dc mov %ebx,%r12d
81e: e9 3b 03 00 00 jmpq b5e <sk_run_filter+0x3a0>
Furthermore, I reordered the instructions to reduce cache line misses by
order the most common instruction to the start.
Signed-off-by: Hagen Paul Pfeifer <hagen@jauu.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
This is a driver for the ADXL345/346 Three-Axis Digital Accelerometers.
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Chris Verges <chrisv@cyberswitching.com>
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
This patch adds the 5241 PHY ID to the broadcom module.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move all PHY IDs to brcmphy.h header for completeness and unification of code.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A column or row configured as a GPI can be programmed to be part
of the key event table and therefore also capable of generating a
key event interrupt. A key event interrupt caused by a GPI follows
the same process flow as a key event interrupt caused by a key
press. GPIs configured as part of the key event table allow single
key switches and other GPI interrupts to be monitored. As part of
the event table, GPIs are represented by the decimal value 97 (0x61
or 1100001) through the decimal value 114 (0x72 or 1110010). See
table below for GPI event number assignments for rows and columns.
GPI Event Number Assignments for Rows
Row0 Row1 Row2 Row3 Row4 Row5 Row6 Row7
97 98 99 100 101 102 103 104
GPI Event Number Assignments for Cols
Col0 Col1 Col2 Col3 Col4 Col5 Col6 Col7 Col8 Col9
105 106 107 108 109 110 111 112 113 114
Signed-off-by: Xiaolong Chen <xiao-long.chen@motorola.com>
Signed-off-by: Yuanbo Ye <yuan-bo.ye@motorola.com>
Signed-off-by: Tao Hu <taohu@motorola.com>
Acked-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
"struct regs" was set to argument of perf_arch_fetch_caller_regs
off-case. It should be "struct pt_regs".
This fixes various build errors in archs that have CONFIG_PERF_EVENTS=y
but no overriden implementation of perf_arch_fetch_caller_regs.
cc1: warnings being treated as errors
In file included from include/linux/ftrace_event.h:8,
from include/trace/syscall.h:6,
from include/linux/syscalls.h:75,
from arch/sh/kernel/sys_sh32.c:9:
include/linux/perf_event.h:937: error: 'struct regs' declared inside parameter list
include/linux/perf_event.h:937: error: its scope is only this definition or declaration, which is probably not what you want
include/linux/perf_event.h: In function 'perf_fetch_caller_regs':
include/linux/perf_event.h:952: error: passing argument 1 of 'perf_arch_fetch_caller_regs' from incompatible pointer type
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com>
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Cc: Paul Mackerras <paulus@samba.org>
Cc: David Miller <davem@davemloft.net>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
LKML-Reference: <AANLkTinKKFKEBQrZ3Hkj-XCaMwaTqulb-XnFzqEYiFRr@mail.gmail.com>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Freeing a perf event can happen in several ways. A task
calls perf_event_exit_task() right before exiting. This helper
will detach all the events from the task context and queue their
removal through free_event() if they are child tasks. The task
also loses its context reference there.
Releasing the breakpoint slot from the constraint table is made
from free_event() that calls release_bp_slot(). We count the number
of breakpoints this task is running by looking at the task's
perf_event_ctxp and iterating through its attached events.
But at this time, the reference to this context has been cleaned up
already.
So looking at the event->ctx instead of task->perf_event_ctxp
to count the remaining breakpoints should solve the problem.
At least it would for child breakpoints, but not for parent ones.
If the parent exits before the child, it will remove all its
events from the context but free_event() will be called later,
on fd release time. And checking the number of breakpoints the
task has attached to its context at this time is unreliable as all
events have been removed from the context.
To solve this, we keep track of the list of per task breakpoints.
On top of it, we maintain our array of numbers of breakpoints used
by the tasks. We use the context address as a task id.
So, instead of looking at the number of events attached to a context,
we walk through our list of per task breakpoints and count the number
of breakpoints that use the same ctx than the one to be reserved or
released from the constraint table, and update the count on top of this
result.
In the meantime it solves a bad refcounting, it also solves a warning,
reported by Paul.
Badness at /home/paulus/kernel/perf/kernel/hw_breakpoint.c:114
NIP: c0000000000cb470 LR: c0000000000cb46c CTR: c00000000032d9b8
REGS: c000000118e7b570 TRAP: 0700 Not tainted (2.6.35-rc3-perf-00008-g76b0f13
)
MSR: 9000000000029032 <EE,ME,CE,IR,DR> CR: 44004424 XER: 000fffff
TASK = c0000001187dcad0[3143] 'perf' THREAD: c000000118e78000 CPU: 1
GPR00: c0000000000cb46c c000000118e7b7f0 c0000000009866a0 0000000000000020
GPR04: 0000000000000000 000000000000001d 0000000000000000 0000000000000001
GPR08: c0000000009bed68 c00000000086dff8 c000000000a5bf10 0000000000000001
GPR12: 0000000024004422 c00000000ffff200 0000000000000000 0000000000000000
GPR16: 0000000000000000 0000000000000000 0000000000000018 00000000101150f4
GPR20: 0000000010206b40 0000000000000000 0000000000000000 00000000101150f4
GPR24: c0000001199090c0 0000000000000001 0000000000000000 0000000000000001
GPR28: 0000000000000000 0000000000000000 c0000000008ec290 0000000000000000
NIP [c0000000000cb470] .task_bp_pinned+0x5c/0x12c
LR [c0000000000cb46c] .task_bp_pinned+0x58/0x12c
Call Trace:
[c000000118e7b7f0] [c0000000000cb46c] .task_bp_pinned+0x58/0x12c (unreliable)
[c000000118e7b8a0] [c0000000000cb584] .toggle_bp_task_slot+0x44/0xe4
[c000000118e7b940] [c0000000000cb6c8] .toggle_bp_slot+0xa4/0x164
[c000000118e7b9f0] [c0000000000cbafc] .release_bp_slot+0x44/0x6c
[c000000118e7ba80] [c0000000000c4178] .bp_perf_event_destroy+0x10/0x24
[c000000118e7bb00] [c0000000000c4aec] .free_event+0x180/0x1bc
[c000000118e7bbc0] [c0000000000c54c4] .perf_event_release_kernel+0x14c/0x170
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Mahesh Salgaonkar <mahesh@linux.vnet.ibm.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Jason Wessel <jason.wessel@windriver.com>
This patch adds transmit power setting type and transmit power level attributes
to NL80211_CMD_SET_WIPHY in order to facilitate adjusting of the transmit power
level of the device.
The added attributes allow selection of automatic, limited or fixed transmit
power level, with the level definable in signed mBm format.
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In preparation for a TX power setting interface in the nl80211, change the
.set_tx_power function to use mBm units instead of dBm for greater accuracy and
smaller power levels.
Also, already in advance move the tx_power_setting enumeration to nl80211.
This change affects the .tx_set_power function prototype. As a result, the
corresponding changes are needed to modules using it. These are mac80211,
iwmc3200wifi and rndis_wlan.
Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: Juuso Oikarinen <juuso.oikarinen@nokia.com>
Acked-by: Samuel Ortiz <samuel.ortiz@intel.com>
Acked-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this patch is implementing IP_NODEFRAG option for IPv4 socket.
The reason is, there's no other way to send out the packet with user
customized header of the reassembly part.
Signed-off-by: Jiri Olsa <jolsa@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some devices, in particular MT devices, produce a lot of data. This
may lead to overflowing of the event queues in evdev driver, which
by default are fairly small. Let the drivers hint the average number
of events per packet generated by the device, and use that information
when computing the buffer size evdev should use for the device.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Chase Douglas <chase.douglas@canonical.com>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
To properly implement 64bits network statistics on 32bit or 64bit hosts,
we provide one new type and four methods, to ease conversions.
Stats producer should use following template granted it already got an
exclusive access to counters (include/linux/u64_stats_sync.h contains
some documentation about details)
u64_stats_update_begin(&stats->syncp);
stats->bytes64 += len;
stats->packets64++;
u64_stats_update_end(&stats->syncp);
While a consumer should use following template to get consistent
snapshot :
u64 tbytes, tpackets;
unsigned int start;
do {
start = u64_stats_fetch_begin(&stats->syncp);
tbytes = stats->bytes64;
tpackets = stats->packets64;
} while (u64_stats_fetch_retry(&stats->lock, syncp));
Suggested by David Miller, and comments courtesy of Nick Piggin.
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Get rid of the last occurances of _v1 suffixes, and move the version
number right after the "uac" string. Now things are consitent again.
Sorry for the forth and back, but it just looks much nicer this way.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Allow one-packet scheduling for UDP connections. When the fwmark-based or
normal virtual service is marked with '-o' or '--ops' options all
connections are created only to schedule one packet. Useful to schedule UDP
packets from same client port to different real servers. Recommended with
RR or WRR schedulers (the connections are not visible with ipvsadm -L).
Signed-off-by: Nick Chalk <nick@loadbalancer.org>
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Patrick McHardy <kaber@trash.net>
The header file include/linux/tracepoint.h may be included without
include/linux/errno.h and then the compiler will fail on building for
undelcared ENOSYS. This patch fixes this problem via including <linux/errno.h>
to include/linux/tracepoint.h.
Signed-off-by: Wu Zhangjin <wuzhangjin@gmail.com>
LKML-Reference: <1277118549-622-1-git-send-email-wuzhangjin@gmail.com>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Added new CAIF protocol type CAIFPROTO_DEBUG for accessing
CAIF debug on the ST Ericsson modems.
There are two debug servers on the modem, one for radio related
debug (CAIF_RADIO_DEBUG_SERVICE) and the other for
communication/application related debug (CAIF_COM_DEBUG_SERVICE).
The debug connection can contain trace debug printouts or
interactive debug used for debugging and test.
Debug connections can be of type STREAM or SEQPACKET.
Signed-off-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add information regarding the 2.6.32 update to the xmit variant of
fw_cdev_event_iso_interrupt.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
The problem:
A target-like userspace driver, e.g. AV/C target or SBP-2/3 target,
needs to be able to act as responder and requester. In the latter role,
it needs to send requests to nods from which it received requests. This
is currently impossible because fw_cdev_event_request lacks information
about sender node ID.
Reported-by: Jay Fenlason <fenlason@redhat.com>
Libffado + libraw1394 + firewire-core is currently unable to drive two
or more audio devices on the same bus.
Reported-by: Arnold Krille <arnold@arnoldarts.de>
This is because libffado requires destination node ID of FCP requests
and sender node ID of FCP responses to match. It even prohibits
libffado from working with a bus on which libraw1394 opens a /dev/fw* as
default ioctl device that does not correspond with the audio device.
This is because libraw1394 does not receive the sender node ID from the
kernel.
Moreover, fw_cdev_event_request makes it impossible to tell unicast and
broadcast write requests apart.
The fix:
Add a replacement of struct fw_cdev_event_request request, boringly
called struct fw_cdev_event_request2. The new event will be sent to a
userspace client instead of the old one if the client claims
compatibility with <linux/firewire-cdev.h> ABI version 4 or later.
libraw1394 needs to be extended to make use of the new event, in order
to properly support libffado and other FCP or address range mapping
users who require correct sender node IDs.
Further notes:
While we are at it, change back the range of possible values of
fw_cdev_event_request.tcode to 0x0...0xb like in ABI version <= 3.
The preceding change "firewire: expose extended tcode of incoming lock
requests to (userspace) drivers" expanded it to 0x0...0x17 which could
catch sloppily coded clients by surprise. The extended range of codes
is only used in the new fw_cdev_event_request2.tcode.
Jay and I also suggested an alternative approach to fix the ABI for
incoming requests: Add an FW_CDEV_IOC_GET_REQUEST_INFO ioctl which can
be called after reception of an fw_cdev_event_request, before issuing of
the closing FW_CDEV_IOC_SEND_RESPONSE ioctl. The new ioctl would reveal
the vital information about a request that fw_cdev_event_request lacks.
Jay showed an implementation of this approach.
The former event approach adds 27 LOC of rather trivial code to
core-cdev.c, the ioctl approach 34 LOC, some of which is nontrivial.
The ioctl approach would certainly also add more LOC to userspace
programs which require the expanded information on inbound requests.
This approach is probably only on the lighter-weight side in case of
clients that want to be compatible with kernels that lack the new
capability, like libraw1394. However, the code to be added to such
libraw1394-like clients in case of the event approach is a straight-
forward additional switch () case in its event handler.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
libraw1394 v2.0.0...v2.0.5 takes FW_CDEV_VERSION from an externally
installed header file and uses it to declare its own implementation
level in FW_CDEV_IOC_GET_INFO. This is wrong; it should set the real
version for which it was actually written.
If we add features to the kernel ABI that require the kernel to check
a client's implementation level, we can not trust the client version if
it was set from FW_CDEV_VERSION.
Hence freeze FW_CDEV_VERSION at the current value (no damage has been
done yet), clearly document FW_CDEV_VERSION as a dummy version and what
clients are expected to do with fw_cdev_get_info.version, and use a new
defined constant (which is not placed into the exported header file) as
kernel implementation level.
Note, in order to check in client program source code which features are
present in an externally installed linux/firewire-cdev.h, use
preprocessor directives like
#ifdef FW_CDEV_IOC_ALLOCATE_ISO_RESOURCE
or
#ifdef FW_CDEV_EVENT_ISO_RESOURCE_ALLOCATED
instead of a check of FW_CDEV_VERSION.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
void (*fw_address_callback_t)(..., int speed, ...) is the speed that a
remote node chose to transmit a request to us. In case of split
transactions, firewire-core will transmit the response at that speed.
Upper layer drivers on the other hand (firewire-net, -sbp2, firedtv, and
userspace drivers) cannot do anything useful with that speed datum,
except log it for debug purposes. But data that is merely potentially
(not even actually) used for debug purposes does not belong into the API.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Push the maintenance of STATE_CLEAR/SET.abdicate down into the card
driver. This way, the read/write_csr_reg driver method works uniformly
across all CSR offsets.
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
by feature variables in the fw_card struct. The hook appeared to be an
unnecessary abstraction in the card driver interface.
Cleaner would be to pass those feature flags as arguments to
fw_card_initialize() or fw_card_add(), but the FairnessControl register
is in the SCLK domain and may therefore not be accessible while Link
Power Status is off, i.e. before the card->driver->enable call from
fw_card_add().
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
This patch adds UFO to the list of GSO features with a software
fallback. This allows UFO to be used even if the hardware does
not support it.
In particular, this allows us to test the UFO fallback, as it
has been reported to not work in some cases.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
To keep the coming code clear and to allow both the sock
code and the scm code to share the logic introduce a
fuction to translate from struct cred to struct ucred.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Pavel Emelyanov <xemul@openvz.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Define what happens when a we view a uid from one user_namespace
in another user_namepece.
- If the user namespaces are the same no mapping is necessary.
- For most cases of difference use overflowuid and overflowgid,
the uid and gid currently used for 16bit apis when we have a 32bit uid
that does fit in 16bits. Effectively the situation is the same,
we want to return a uid or gid that is not assigned to any user.
- For the case when we happen to be mapping the uid or gid of the
creator of the target user namespace use uid 0 and gid as confusing
that user with root is not a problem.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Acked-by: Serge E. Hallyn <serue@us.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that RCU debugging checks for matching rcu_dereference calls
and rcu_read_lock, we need to use the correct primitives or face
nasty warnings.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
In old kernels, NET_SKB_PAD was defined to 16.
Then commit d6301d3dd1 (net: Increase default NET_SKB_PAD to 32), and
commit 18e8c134f4 (net: Increase NET_SKB_PAD to 64 bytes) increased it
to 64.
While first patch was governed by network stack needs, second was more
driven by performance issues on current hardware. Real intent was to
align data on a cache line boundary.
So use max(32, L1_CACHE_BYTES) instead of 64, to be more generic.
Remove microblaze and powerpc own NET_SKB_PAD definitions.
Thanks to Alexander Duyck and David Miller for their comments.
Suggested-by: David Miller <davem@davemloft.net>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ndo_get_stats still returns struct net_device_stats *; there is
no struct net_device_stats64.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register net_bridge_port pointer as rx_handler data pointer. As br_port is
removed from struct net_device, another netdev priv_flag is added to indicate
the device serves as a bridge port. Also rcuized pointers are now correctly
dereferenced in br_fdb.c and in netfilter parts.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Register macvlan_port pointer as rx_handler data pointer. As macvlan_port is
removed from struct net_device, another netdev priv_flag is added to indicate
the device serves as a macvlan port.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Acked-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add possibility to register rx_handler data pointer along with a rx_handler.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the helper netpoll_tx_running for use within
ndo_start_xmit. It returns non-zero if ndo_start_xmit is being
invoked by netpoll, and zero otherwise.
This is currently implemented by simply looking at the hardirq
count. This is because for all non-netpoll uses of ndo_start_xmit,
IRQs must be enabled while netpoll always disables IRQs before
calling ndo_start_xmit.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the functions __netpoll_setup/__netpoll_cleanup
which is designed to be called recursively through ndo_netpoll_seutp.
They must be called with RTNL held, and the caller must initialise
np->dev and ensure that it has a valid reference count.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
Grant Likely