xen_init_spinlocks() currently calls static_key_slow_inc() before
jump_label_init() is invoked. When CONFIG_JUMP_LABEL is set (which usually is
the case) the effect of this static_key_slow_inc() is deferred until after
jump_label_init(). This is different from when CONFIG_JUMP_LABEL is not set, in
which case the key is set immediately. Thus, depending on the value of config
option, we may observe different behavior.
In addition, when we come to __jump_label_transform() from jump_label_init(),
the key (paravirt_ticketlocks_enabled) is already enabled. On processors where
ideal_nop is not the same as default_nop this will cause a BUG() since it is
expected that before a key is enabled the latter is replaced by the former
during initialization.
To address this problem we need to move
static_key_slow_inc(¶virt_ticketlocks_enabled) so that it is called
after jump_label_init(). We also need to make sure that this is done before
other cpus start to boot. early_initcall appears to be a good place to do so.
(Note that we cannot move whole xen_init_spinlocks() there since pv_lock_ops
need to be set before alternative_instructions() runs.)
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
[v2: Added extra comments in the code]
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
cpu_reset is already #defined in <asm/proc-fns.h> as processor.reset,
so it expands here and causes problems.
Cc: <stable@vger.kernel.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Christoffer Dall <christoffer.dall@linaro.org>
This property is no longer required by the GPIO binding. Remove it.
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
e5c9b4cd66 ("sh_eth: get R8A7740 support
out of #ifdef") exchanged sh-eth driver name to r8a7740-gether, but,
eva_pinctrl_map[] didn't follow it. Fixes it.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Patch 638591c enabled building the AES assembler code in Thumb2 mode.
However, this code used arithmetic involving PC rather than adr{l}
instructions to generate PC-relative references to the lookup tables,
and this needs to take into account the different PC offset when
running in Thumb mode.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Cc: stable@vger.kernel.org
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This prevents the linker erroring with:
arm-linux-ld: error: arch/arm/lib/xor-neon.o uses VFP instructions, whereas arch/arm/lib/built-in.o does not
arm-linux-ld: failed to merge target specific data of file arch/arm/lib/xor-neon.o
This is due to the non-neon files being marked as containing FPA data/
instructions (even though they do not) being mixed with files which
contain VFP, which is an incompatible floating point format.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 377747c406 ("ARM: entry: allow ARM-private syscalls to be
restarted") reworked the low-level syscall dispatcher to allow
restarting of ARM-private syscalls. Unfortunately, this relocated the
label used to dispatch a private syscall from the trace path, so that
the invocation would be bypassed altogether!
This causes applications to fail under strace as soon as they rely on
a private syscall (e.g. set_tls):
set_tls(0xb6fad4c0, 0xb6fadb98, 0xb6fb1050, 0xb6fad4c0, 0xb6fb1050)
= -1 ENOSYS (Function not implemented)
This patch fixes the label so that we correctly dispatch private
syscalls from the trace path.
Reported-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Tested-by: Jason Gunthorpe <jgunthorpe@obsidianresearch.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Currently on the Lager board NFS timeouts/delays are seen when booting. That
turned out to happen because the SoC's ETH_LINK signal turns on and off after
each packet. It is connected to Micrel KSZ8041 PHY's LED0 signal. Ether LEDs
on the Lager board are named LINK and ACTIVE which corresponds to non-default
01 setting of the PHY control register 1 bits 14-15. The 'sh_eth' driver resets
the PHY when opening the network device, so we have to set the mentioned bits
back to 01 from the default 00 value which causes bouncing of ETH_LINK. That
can be achieved using the PHY platform fixup mechanism if we also modify the
driver to use it..
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Currently DT compatibility strings of both types can be found in the kernel
sources: <unit>-<soc> and <soc>-<unit>, whereas a unique format should be
followed and the former one is preferred. This patch converts the SDHI
MMC driver and its users to the common standard. This is safe for now, since
ATM no real products are using this driver with DT.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski+renesas@gmail.com>
Acked-by: Chris Ball <cjb@laptop.org>
[Removed r8a7740.dtsi portion as it is not applicable]
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
1) Four fixes for cpufreq regressions introduced by the changes that
removed Device Tree parsing for CPU device nodes from cpufreq
drivers from Sudeep KarkadaNagesha.
2) Two fixes for recent cpufreq regressions introduced by changes
related to the preservation of sysfs attributes over system
suspend/resume cycles from Viresh Kumar.
3) Fix for ACPI-based wakeup signaling in the PCI subsystem that
fails to stop PME polling for devices put into the D3cold power
state from Rafael J Wysocki.
4) Fix for bad interactions between cpufreq and udev on systems
supporting intel_pstate where acpi-cpufreq is available as well
from Yinghai Lu.
/
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=8EeE
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management fixes from Rafael Wysocki:
1) Four fixes for cpufreq regressions introduced by the changes that
removed Device Tree parsing for CPU device nodes from cpufreq
drivers from Sudeep KarkadaNagesha.
2) Two fixes for recent cpufreq regressions introduced by changes
related to the preservation of sysfs attributes over system
suspend/resume cycles from Viresh Kumar.
3) Fix for ACPI-based wakeup signaling in the PCI subsystem that
fails to stop PME polling for devices put into the D3cold power
state from Rafael J Wysocki.
4) Fix for bad interactions between cpufreq and udev on systems
supporting intel_pstate where acpi-cpufreq is available as well
from Yinghai Lu.
* tag 'pm+acpi-3.12-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpufreq: return EEXIST instead of EBUSY for second registering
PCI / ACPI / PM: Clear pme_poll for devices in D3cold on wakeup
ARM: shmobile: change dev_id to cpu0 while registering cpu clock
ARM: i.MX: change dev_id to cpu0 while registering cpu clock
cpufreq: imx6q-cpufreq: assign cpu_dev correctly to cpu0 device
cpufreq: cpufreq-cpu0: assign cpu_dev correctly to cpu0 device
cpufreq: unlock correct rwsem while updating policy->cpu
cpufreq: Clear policy->cpus bits in __cpufreq_remove_dev_finish()
---------------------------
This pull request includes:
1) A patch to fix build breakage with DEBUG_LL
2) A patch to quell a build-time warning.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=mFB9
-----END PGP SIGNATURE-----
Merge tag 'davinci-fixes-for-v3.12-rc2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into fixes
From Sekhar Nori, DaVinci fixes for v3.12-rc2:
- a fix build breakage with DEBUG_LL
- a quell a build-time warning
* tag 'davinci-fixes-for-v3.12-rc2-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: dm365 evm: fix unused variable warning
ARM: davinci: fix build breakage with DEBUG_LL
Signed-off-by: Olof Johansson <olof@lixom.net>
- mvebu
- fix reference leaks by adding of_node_put()
- update Armada XP DT clock properties to restore booting
- kirkwood
- add missing reg property for cpu@0
- fix typo in address of second XOR engine
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
iQEcBAABAgAGBQJSO8JQAAoJEAi3KVZQDZAe660IAJV2Zqc/iMxmRJLCPoFnSpGd
uFsthQx0e+OGVW+KowykPve2p6RxOqol2wR1IvgMlkCPFBtUGhGkEeXvJ1wenS9H
JNEtG7fU6AAiaw9dfS6OJtPMxQK3yTSjkVcuaNi0Ds/q99ja9ZYR6RPYzqe8kQME
k9dX3OGNzm+nI7BKheVYcB4zmxBfCtSHzBe2tdwK6mdoki9Qdt4FY4LosXwQHt4d
5BjHGLLgbOp/fCrztgYD4ZiuuJekXz51OP1ut2giIdlakgW0DIRCRadyLyyZMH7S
Wrl636TaYAdh/jXu00mTZIj13K0NDXcERjemjb7O16LFB0fAIz+DYXVVM2nB1iE=
=B2UP
-----END PGP SIGNATURE-----
Merge tag 'fixes-3.12' of git://git.infradead.org/linux-mvebu into fixes
From Jason Cooper, mvebu fixes for v3.12:
- mvebu
- fix reference leaks by adding of_node_put()
- update Armada XP DT clock properties to restore booting
- kirkwood
- add missing reg property for cpu@0
- fix typo in address of second XOR engine
* tag 'fixes-3.12' of git://git.infradead.org/linux-mvebu:
ARM: kirkwood: Fix address of second XOR engine
ARM: mvebu: Add clock properties to Armada XP timer node
ARM: mvebu: Add the reference 25 MHz fixed-clock to Armada XP
ARM: Kirkwood: Add missing DT reg property to cpu@0
bus: mvebu: add missing of_node_put() to fix reference leak
ARM: mvebu: add missing of_node_put() to fix reference leak
Signed-off-by: Olof Johansson <olof@lixom.net>
- Documentation clarification on tagged pointers
- hwcap widened to 64-bit (user space already reading it as 64-bit)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.9 (GNU/Linux)
iQIcBAABAgAGBQJSPEd3AAoJEGvWsS0AyF7xHFwQAIZZq6qbhEuojbrRxRSU1/Il
4VuPIJIdFW+T09uzE9d9ER1LJkQlG9+RkffOZWZaqQ+kVpwtH8YImWpvKBA+JHc+
IgwTOFEQ8c6JJS/g1XzJdm/0ykR/ZzOhavqbgWDpuJsjsw4aXbxTlWoE34/ZlVeo
zn4QiirbzkUEsMNlV/Di6EdVkwdJ8WTvrFWxpyR2teSokgTKNACv2fwdxYz+ggS+
+dwoqcQD122SogT72ti5LriGRucOynH1gjHETRTEfXkdAeCdMgjJ6jnVRLJEX9Je
Qv7Q9YHI8eCFpv4rGKvSJ7GtYJWY3Vsjp/t1dSmXtw5+ctFQgKqpT5tyG4yHC1DU
huR2/Ui5RuEYHHiMMBCFp9JOvceab9lBFbTrsLTJto6kRg8E3nkEAdVNcgb5MLRE
jcgwquK4HfF1JW3+l9rKClKz7fo3eVoA/cR92i5VdBjwzoL6pqKSk3pbPro+557k
q/gbQhiggX4kTcv16tfVvzcfWwi7xRRJyFMm1W/VqniJa+gkEptpzfdtvdZOxKCx
bUDp7LRwejRAMPTVp8MJZY4NvA68jJucRuenYDKZ6UVN5LQl0rcCPTvfOtafy44M
CwArqPpP9/wUInqYQhjBLvp0yMSndthhatoCjLUdee+YkhMbvLqAzOyu2Vp2CVqf
ib5Roul1AuFWqWFRqJrN
=OICB
-----END PGP SIGNATURE-----
Merge tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64
Pull ARM64 fixes from Catalin Marinas:
- Compat register fault reporting fix
- Documentation clarification on tagged pointers
- hwcap widened to 64-bit (user space already reading it as 64-bit)
* tag 'arm64-stable' of git://git.kernel.org/pub/scm/linux/kernel/git/cmarinas/linux-aarch64:
arm64: Widen hwcap to be 64 bit
arm64: Correctly report LR and SP for compat tasks
arm64: documentation: tighten up tagged pointer documentation
arm64: Make do_bad_area() function static
Under arm64 elf_hwcap is a 32 bit quantity, but it is stored in
a 64 bit auxiliary ELF field and glibc reads hwcap as 64 bit.
This patch widens elf_hwcap to be 64 bit.
Signed-off-by: Steve Capper <steve.capper@arm.com>
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
When a task crashes and we print debugging information, ensure that
compat tasks show the actual AArch32 LR and SP registers rather than the
AArch64 ones.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
we've never encountered the bug on i386 - Josh Boyer
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=nm0S
-----END PGP SIGNATURE-----
Merge tag 'efi-urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/mfleming/efi into x86/urgent
Pull EFI fix from Matt Flemin:
" * Fix WARNING on i386 by only enabling a workaround for x86-64 since
we've never encountered the bug on i386 - Josh Boyer "
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Solve the problems around the broken definition of perf_event_mmap_page::
cap_usr_time and cap_usr_rdpmc fields which used to overlap, partially
fixed by:
860f085b74 ("perf: Fix broken union in 'struct perf_event_mmap_page'")
The problem with the fix (merged in v3.12-rc1 and not yet released
officially), noticed by Vince Weaver is that the new behavior is
not detectable by new user-space, and that due to the reuse of the
field names it's easy to mis-compile a binary if old headers are used
on a new kernel or new headers are used on an old kernel.
To solve all that make this change explicit, detectable and self-contained,
by iterating the ABI the following way:
- Always clear bit 0, and rename it to usrpage->cap_bit0, to at least not
confuse old user-space binaries. RDPMC will be marked as unavailable
to old binaries but that's within the ABI, this is a capability bit.
- Rename bit 1 to ->cap_bit0_is_deprecated and always set it to 1, so new
libraries can reliably detect that bit 0 is deprecated and perma-zero
without having to check the kernel version.
- Use bits 2, 3, 4 for the newly defined, correct functionality:
cap_user_rdpmc : 1, /* The RDPMC instruction can be used to read counts */
cap_user_time : 1, /* The time_* fields are used */
cap_user_time_zero : 1, /* The time_zero field is used */
- Rename all the bitfield names in perf_event.h to be different from the
old names, to make sure it's not possible to mis-compile it
accidentally with old assumptions.
The 'size' field can then be used in the future to add new fields and it
will act as a natural ABI version indicator as well.
Also adjust tools/perf/ userspace for the new definitions, noticed by
Adrian Hunter.
Reported-by: Vince Weaver <vincent.weaver@maine.edu>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Also-Fixed-by: Adrian Hunter <adrian.hunter@intel.com>
Link: http://lkml.kernel.org/n/tip-zr03yxjrpXesOzzupszqglbv@git.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
uncore_validate_group() can't call smp_processor_id() because it is
in preemptible context. Pass NUMA_NO_NODE to the allocator instead.
Signed-off-by: Yan, Zheng <zheng.z.yan@intel.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1379400493-11505-1-git-send-email-zheng.z.yan@intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There appears to be an error in the second address of the second XOR
engine in the Kirkwood SoC device tree, which is specified as 0xd0b00
but should be 0x60b00.
For confirmation of address see table 581 page 658 of:
http://www.marvell.com/embedded-processors/kirkwood/assets/FS_88F6180_9x_6281_OpenSource.pdf
Also see definition of XOR1_HIGH_PHYS_BASE in
arch/arm/mach-kirkwood/include/mach/kirkwood.h
Signed-off-by: Quentin Armitage <quentin@armitage.org.uk>
Reviewed-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
A set of fixes for ARM platforms for 3.12. Among them:
- A fix for build breakage in the MTD subsystem for some PXA devices.
David Woodhouse has this patch in his for-next branch but has not been
responding to our requests to send it up so here it is.
I should have amended the commit message to describe the build failure for
CONFIG_OF=n setups, but forgot and now it's down in the stack of commits.
- Added device-tree for the BeagleBone Black. Turns out people have been
using the older "regualar" bone DT for the newer boards, and there's
risk of damaging hardware that way.
- Misc DT and regular fixes for OMAP.
- Fix to make the ST-Ericsson "snowball" boards boot with
multi_v7_defconfig, and enable one of the ST-E reference boards on the
same config.
- Kconfig cleanup for u300 to hide submenus when the platform isn't
enabled.
- Enable ARM_ATAG_DTB_COMPAT to let firmware override command
line when booting with an appended devicetree on non-DT-enabled
firmware (needed to boot snowball).
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=I14p
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A set of fixes for ARM platforms for 3.12. Among them:
- A fix for build breakage in the MTD subsystem for some PXA devices.
David Woodhouse has this patch in his for-next branch but has not
been responding to our requests to send it up so here it is. I
should have amended the commit message to describe the build
failure for CONFIG_OF=n setups, but forgot and now it's down in the
stack of commits.
- Added device-tree for the BeagleBone Black. Turns out people have
been using the older "regualar" bone DT for the newer boards, and
there's risk of damaging hardware that way.
- Misc DT and regular fixes for OMAP.
- Fix to make the ST-Ericsson "snowball" boards boot with
multi_v7_defconfig, and enable one of the ST-E reference boards on
the same config.
- Kconfig cleanup for u300 to hide submenus when the platform isn't
enabled.
- Enable ARM_ATAG_DTB_COMPAT to let firmware override command line
when booting with an appended devicetree on non-DT-enabled firmware
(needed to boot snowball)"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (26 commits)
ARM: multi_v7: add HREFv60 to multi_v7 defconfig
ARM: OMAP2+: mux: fix trivial typo in name
ARM: OMAP4 SMP: Corrected a typo fucntions to functions
ARM: OMAP4: cpuidle: fix: call cpu_cluster_pm_exit conditionally
mailbox: remove unnecessary platform_set_drvdata()
ARM: mach-omap2: gpmc: Fix warning when CONFIG_ARM_LPAE=y
ARM: OMAP: fix return value check in omap_device_build_from_dt()
ARM: OMAP4: Fix clock_get error for GPMC during boot
ARM: sa1100: collie.c: fall back to jedec_probe flash detection
ARM: u300: hide submenus
ARM: dts: igep00x0: Add pinmux configuration for MCBSP2
ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for blaze
ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for pandaboard
mtd: nand: pxa3xx: Remove unneeded ifdef CONFIG_OF
ARM: multi_v7_defconfig: enable ARM_ATAG_DTB_COMPAT
ARM: ux500: disable outer cache debug
ARM: dts: OMAP5: fix ocp2scp DTS data
ARM: dts: OMAP5: fix reg property size
ARM: dts: am335x-bone*: add DT for BeagleBone Black
ARM: dts: omap3-beagle-xm: fix string error in compatible property
...
Pull MIPS updates from Ralf Baechle:
- Minor updates and fixes to the Octeon ethernet driver in staging
- A fix to VGA_MAP_MEM() for 64 bit platforms
- Fix a workaround for 74K/1074K processors
- The symlink arch/mips/boot/dts/include/dt-bindings was pointing to a
a file with a name ending in \n. I think this may have been caused
by a git bug with with patches sent by email
- A build fix for VGA console on BCM1480-based systems
- Fix PCI device access via "/sys/bus/pci/.../resource0" or similar
work for Alchemy platforms
- Fix potential data leak on MIPS R5 cores. This doesn't add proper
support for any R5 features, just ensures a kernel without such
support will be secure to run
- Adding a macros for the CP0 Config5 register to be used by the R5 fix
- Make get_cycles() actually return something useful where possible
This also requires a preparatory patch for performance sake
- Fix a warning about the use of smp_processor_id() in preemptible
code. Again this includes a preparatory patch adding the
infrastructure to be used by the actual patch
- Finally remove pointless one-line comment
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: Fix invalid symbolic link file
MIPS: PCI: pci-bcm1480: Include missing vt.h header
MIPS: Disable usermode switching of the FR bit for MIPS R5 CPUs.
MIPS: Add MIPS R5 config5 register.
MIPS: PCI: Use pci_resource_to_user to map pci memory space properly
MIPS: 74K/1074K: Correct erratum workaround.
MIPS: Cleanup CP0 PRId and CP1 FPIR register access masks
MIPS: Remove useless comment about kprobe from arch/mips/Makefile
MIPS: Fix VGA_MAP_MEM macro.
MIPS: Reimplement get_cycles().
MIPS: Optimize current_cpu_type() for better code.
MIPS: Fix accessing to per-cpu data when flushing the cache
MIPS: Provide nice way to access boot CPU's data.
staging: octeon-ethernet: rgmii: enable interrupts that we can handle
staging: octeon-ethernet: remove skb alloc failure warnings
staging: octeon-ethernet: make dropped packets to consume NAPI budget
This flag is a NOOP since 2.6.36 and can be removed.
This is an update for 3.11 of a patch already sent for 3.10
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Replace pinctrl_usart2_rts and pinctrl_usart2_cts istead of pinctrl_uart2_*.
Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
It's needed for the MAX_NR_CONSOLES macro.
Fixes the following build problem on a randconfig:
arch/mips/pci/pci-bcm1480.c: In function 'bcm1480_pcibios_init':
arch/mips/pci/pci-bcm1480.c:261:36: error: 'MAX_NR_CONSOLES'
undeclared (first use in this function)
arch/mips/pci/pci-bcm1480.c:261:36: note: each undeclared
identifier is reported only once for each function it appears in
make[1]: *** [arch/mips/pci/pci-bcm1480.o] Error 1
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5858/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
If neither CONFIG_SND_DM365_AIC3X_CODEC nor CONFIG_SND_DM365_VOICE_CODEC
are defined, we may get warnings like:
arch/arm/mach-davinci/board-dm365-evm.c:179:33: warning: 'dm365_evm_snd_data' defined but not used [-Wunused-variable]
To fix this, just mark the struct as __maybe_unused.
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Cc: Sekhar Nori <nsekhar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
commit fcf7157 ("ARM: davinci: serial: get rid of davinci_uart_config")
introduced build breakage because of a misplaced
header file include which cause a bunch of errors when
the file is included in assembly code (like debug-macro.S)
Fix the build breakage.
Reported-by: Alexander Holler <holler@ahsoftware.de>
Tested-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Currently the kernel will always use the FR=0 register model for O32. If
an O32 application did enable FR=1 mode, some data from another application
might be leaked in the extra registers becoming visible.
Iow, this patch is meant to make the kernel MIPS R5 tolerant but leaves
proper MIPS R5 support to a future patchset.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Currently all clkdev registration use "cpufreq-cpu0.0" as dev_id
for cpu clock which refers to virtual platform device. It needs to
be "cpu0" instead which is actual cpu0 device id.
This patch changes the dev_id from "cpufreq-cpu0.0" to "cpu0".
Reported-and-tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Magnus Damm <damm@opensource.se>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Currently all clkdev registration use "cpufreq-cpu0.0" as dev_id
for cpu clock which refers to virtual platform device. It needs to
be "cpu0" instead which is actual cpu0 device id.
This patch changes the dev_id from "cpufreq-cpu0.0" to "cpu0".
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Commit cdc58d602d "cpufreq: imx6q-cpufreq:
remove device tree parsing for cpu nodes" assumed the pdev->dev is set to
cpu0 device in the platform code. But it actually points to the virtual
cpufreq-cpu0 platform device which is not present in the device tree.
Most of the information needed by cpufreq is stored in cpu0 DT node.
So cpu_dev must point to cpu0 device.
This patch fixes the wrong assignment to cpu_dev.
Reported-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Sudeep KarkadaNagesha <sudeep.karkadanagesha@arm.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[ralf@linux-mips.org: This only matters to Alchemy platforms. On other
platforms fixup_bigphys_addr is just an identidy mapping.]
Signed-off-by: Wolfgang Grandegger <wg@denx.de>
Cc: tiejun.chen <tiejun.chen@windriver.com>
Cc: Linux-MIPS <linux-mips@linux-mips.org>
Patchwork: https://patchwork.linux-mips.org/patch/1868/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
regressions and avoid electrical issues on beaglebone black.
Via Benoit Cousson <bcousson@baylibre.com>:
Fix BBB LDO voltage to avoid HDMI destruction
Fix OMAP5 wrong attribute
Fix typo in beagle xM strings
Fix missing pinmux and regulator for OMAP4 wifi
Fix missing pinmux for igep headset
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=JZua
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.12/fixes-dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren, OMAP DT fixes for 3.12-rc1:
OMAP device tree changes that are needed to fix regressions and avoid
electrical issues on beaglebone black.
Via Benoit Cousson <bcousson@baylibre.com>:
Fix BBB LDO voltage to avoid HDMI destruction
Fix OMAP5 wrong attribute
Fix typo in beagle xM strings
Fix missing pinmux and regulator for OMAP4 wifi
Fix missing pinmux for igep headset
* tag 'omap-for-v3.12/fixes-dt-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: igep00x0: Add pinmux configuration for MCBSP2
ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for blaze
ARM: dts: Fix muxing and regulator for wl12xx on the SDIO bus for pandaboard
ARM: dts: OMAP5: fix ocp2scp DTS data
ARM: dts: OMAP5: fix reg property size
ARM: dts: am335x-bone*: add DT for BeagleBone Black
ARM: dts: omap3-beagle-xm: fix string error in compatible property
Signed-off-by: Olof Johansson <olof@lixom.net>
a few trivial typo fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=HQjo
-----END PGP SIGNATURE-----
Merge tag 'omap-for-v3.12/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
From Tony Lindgren, fixes for 3.12-rc1:
OMAP fixes for build warnings and cpuidle, and a few trivial typo fixes.
* tag 'omap-for-v3.12/fixes-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: mux: fix trivial typo in name
ARM: OMAP4 SMP: Corrected a typo fucntions to functions
ARM: OMAP4: cpuidle: fix: call cpu_cluster_pm_exit conditionally
mailbox: remove unnecessary platform_set_drvdata()
ARM: mach-omap2: gpmc: Fix warning when CONFIG_ARM_LPAE=y
ARM: OMAP: fix return value check in omap_device_build_from_dt()
ARM: OMAP4: Fix clock_get error for GPMC during boot
Signed-off-by: Olof Johansson <olof@lixom.net>
This is just a standard board for the Ux500, include it in the
v7 multiplatform defconfig.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Corrected the functions spelling mistake in the OMAP4 SMP source file.
Signed-off-by: Anoop Thomas Mathew <atm@profoundis.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When CONFIG_ARM_LPAE=y the following build warning is generated:
arch/arm/mach-omap2/gpmc.c:1495:4: warning: format '%x' expects argument of type 'unsigned int', but argument 4 has type 'resource_size_t' [-Wformat]
According to Documentation/printk-formats.txt '%pa' can be used to properly
print 'resource_size_t'.
Reported-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In case of error, the function omap_device_alloc() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check
should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Looks like we still have the legacy clock alias name for
omap4 GPMC (General Purpose Memory Controller), so let's
fix it for the device tree naming. There's no need to keep
the legacy naming as omap4 is DT only nowadays.
Without this fix we get the following error while booting:
[ 0.440399] omap-gpmc 50000000.gpmc: error: clk_get
Reported-by: Olof Johansson <olof@lixom.net>
Cc: stable@vger.kernel.org # v3.11
Signed-off-by: Tony Lindgren <tony@atomide.com>
Make sure 74K revision numbers are not applied to the 1074K. Also catch
invalid usage.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5857/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Replace hardcoded CP0 PRId and CP1 FPIR register access masks throughout.
The change does not touch places that use shifted or partial masks.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5838/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
With the addition of the Armada XP reference clock, we can now model
accurately the available clock inputs for the timer: namely, nbclk
and refclk. For each of this clock inputs we assign a name, for the
driver to select as appropriate.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The Armada XP SoC has a reference 25 MHz fixed-clock that is used in
some controllers such as the timer and the watchdog. This commit adds
a DT representation of this clock through a fixed-clock compatible node.
Signed-off-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Acked-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
The kirkwood.dtsi cpu@0 node is missing the mandatory reg property.
This causes of_get_cpu_node() to fail to find the node and as a result
the cpufreq driver fails in its probe function.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Add of_node_put to properly decrement the refcount when we are
done using a given node.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Reviewed-by: Ezequiel Garcia <ezequiel.garcia@free-electrons.com>
Signed-off-by: Jason Cooper <jason@lakedaemon.net>
Conflicts:
arch/arm/mach-mvebu/armada-370-xp.c
arch/arm/mach-mvebu/platsmp.c
Pull x86 fixes from Ingo Molnar:
"Misc fixes"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/intel/lpss: Add pin control support to Intel low power subsystem
perf/x86/intel: Mark MEM_LOAD_UOPS_MISS_RETIRED as precise on SNB
x86: Remove now-unused save_rest()
x86/smpboot: Fix announce_cpu() to printk() the last "OK" properly
Zaurus collie contains 2 LH28F640BFHE-PTTL90 (64M 4Mx16) and
at the moment cfi will not detect the collie NOR.
In the meanwhile we can revert to the jedec-probe map which has been
fixed with following commit:
mtd: jedec_probe: fix LH28F640BF definition
fe2f4c8e0b
Somehow this is unsatisfactory because the flash is mounted READ ONLY
(as from factory, with a RO cramfs)
Signed-off-by: Andrea Adami <andrea.adami@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
Right now the U300 submenus are showcased for everyone even if
we're not on v5 multiplatforms. Hide this in the multiplatform
configuration properly.
Cc: arm@kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
Use the CKSEG1ADDR macro when calculating VGA_MAP_MEM.
[ralf@linux-mips.org: Include <asm/addrspace.h for CKSEG1ADDR.]
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5814/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This essentially reverts commit efb9ca08b5
(kernel.org) / 58020a106879a8b372068741c81f0015c9b0b96dbv [[MIPS] Change
get_cycles to always return 0.]
Most users of get_cycles() invoke it as a timing interface. That's why
in modern kernels it was never very much missed for. /dev/random however
uses get_cycles() in the how the jitter in the interrupt timing contains
some useful entropy.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Add patch to fix 32bit EFI service mapping (rhbz 726701)
Multiple people are reporting hitting the following WARNING on i386,
WARNING: at arch/x86/mm/ioremap.c:102 __ioremap_caller+0x3d3/0x440()
Modules linked in:
Pid: 0, comm: swapper Not tainted 3.9.0-rc7+ #95
Call Trace:
[<c102b6af>] warn_slowpath_common+0x5f/0x80
[<c1023fb3>] ? __ioremap_caller+0x3d3/0x440
[<c1023fb3>] ? __ioremap_caller+0x3d3/0x440
[<c102b6ed>] warn_slowpath_null+0x1d/0x20
[<c1023fb3>] __ioremap_caller+0x3d3/0x440
[<c106007b>] ? get_usage_chars+0xfb/0x110
[<c102d937>] ? vprintk_emit+0x147/0x480
[<c1418593>] ? efi_enter_virtual_mode+0x1e4/0x3de
[<c102406a>] ioremap_cache+0x1a/0x20
[<c1418593>] ? efi_enter_virtual_mode+0x1e4/0x3de
[<c1418593>] efi_enter_virtual_mode+0x1e4/0x3de
[<c1407984>] start_kernel+0x286/0x2f4
[<c1407535>] ? repair_env_string+0x51/0x51
[<c1407362>] i386_start_kernel+0x12c/0x12f
Due to the workaround described in commit 916f676f8 ("x86, efi: Retain
boot service code until after switching to virtual mode") EFI Boot
Service regions are mapped for a period during boot. Unfortunately, with
the limited size of the i386 direct kernel map it's possible that some
of the Boot Service regions will not be directly accessible, which
causes them to be ioremap()'d, triggering the above warning as the
regions are marked as E820_RAM in the e820 memmap.
There are currently only two situations where we need to map EFI Boot
Service regions,
1. To workaround the firmware bug described in 916f676f8
2. To access the ACPI BGRT image
but since we haven't seen an i386 implementation that requires either,
this simple fix should suffice for now.
[ Added to changelog - Matt ]
Reported-by: Bryan O'Donoghue <bryan.odonoghue.lkml@nexus-software.ie>
Acked-by: Tom Zanussi <tom.zanussi@intel.com>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Matthew Garrett <mjg59@srcf.ucam.org>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: <stable@vger.kernel.org>
Signed-off-by: Josh Boyer <jwboyer@redhat.com>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Add pinmux configuration for MCBSP2 connected to the TDM interface.
With this configuration the Headset modules works as expected.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
BTRFS is now relying on those since v3.12-rc1.
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Commit 76787b3b (ARM: OMAP2+: Remove board-4430sdp.c)
removed legacy booting in favor of device tree based booting
for 4430sdp. That caused the WLAN to stop working as the
related .dts entries fell through the cracks.
I don't have the "1283 PG 2.21 connectivity device" on my 4430sdp,
but the earlier version of this patch was tested by Luciano
Coelho. This version has left out the input logic for MMC CLK
line compared to the earlier version as that is not bidirectional,
and should be safe to do.
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Luciano Coelho <luca@coelho.fi>
Cc: Ruslan Bilovol <ruslan.bilovol@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Commit b42b9181 (ARM: OMAP2+: Remove board-omap4panda.c)
removed legacy booting in favor of device tree based booting
for pandaboard. That caused the WLAN to stop working as the
related .dts entries fell through the cracks.
The legacy muxing was setting pulls for GPIO 48 and 49, so let's
keep that behaviour for now to avoid further regressions for
BT and FM. Also input logic was enabled for MMC CLK line, but
I've verified that the input logic we don't need enabled for
CLK line as it's not bidirectional.
Also, we want to use non-removable instead of ti,non-removable
as the ti,non-removable also sets no_regulator_off_init which
is really not what we want as then wl12xx won't get powered
up and down which is needed for resetting it.
Note that looks like the WLAN interface fails to come up after
a warm reset, but that most likely was also happening with
the legacy booting and needs a separate fix.
Cc: Paolo Pisati <p.pisati@gmail.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Cc: Luciano Coelho <luca@coelho.fi>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
Pull KVM fixes from Gleb Natapov.
* 'fixes' of git://git.kernel.org/pub/scm/virt/kvm/kvm:
KVM: VMX: set "blocked by NMI" flag if EPT violation happens during IRET from NMI
kvm: free resources after canceling async_pf
KVM: nEPT: reset PDPTR register cache on nested vmentry emulation
KVM: mmu: allow page tables to be in read-only slots
KVM: x86 emulator: emulate RETF imm
o Move current_cpu_type() to a separate header file
o #ifdefing on supported CPU types lets modern GCC know that certain
code in callers may be discarded ideally turning current_cpu_type() into
a function returning a constant.
o Use current_cpu_type() rather than direct access to struct cpuinfo_mips.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5833/
Set "blocked by NMI" flag if EPT violation happens during IRET from NMI
otherwise NMI can be called recursively causing stack corruption.
Signed-off-by: Gleb Natapov <gleb@redhat.com>
* A couple of clock driver and device tree fixes
* A bug fix for clk-fixup-mux to get imx6sl back to boot
* A L2 cache setting fix for imx6q
* One pinctrl macro fix for UART2 DTE entries
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJSOHJ2AAoJEFBXWFqHsHzOC/kIAK4Usv+HBpiGmE53S1GpZ6fZ
bsVokOUMyEa8bioF5tHJyK+TNhWkT3I8I7VolhQMhkDkmVctVmGHHGBffP4rS3Zi
iP1z+DXgatRLXpWCeuSN4iXaUuw9eA9/agt3H9NEhPT/uZtaTO6AoWDNPzoxaA+e
SiU+g/t1sQGTfz0J7NS9WOBTjesElTgrO+iJRSicvRrBDRS+mr38b4TbLrec7ZZ9
GTpa1bFwuq0D99iaV4W8fJuo6mYaDTb2yX2PTdB9hTl1A5f9vp64ccHDgY5pwo2+
EUNpGG3UdGjk0DXKc2lIDI/nVUKfrWUKOn8WP+Kj90Kvco8jFi4QdqKNzbjHCsE=
=NCVi
-----END PGP SIGNATURE-----
Merge tag 'imx-fixes-3.12' of git://git.linaro.org/people/shawnguo/linux-2.6 into fixes
From Shawn Guo, imx fixes for 3.12:
* A couple of clock driver and device tree fixes
* A bug fix for clk-fixup-mux to get imx6sl back to boot
* A L2 cache setting fix for imx6q
* One pinctrl macro fix for UART2 DTE entries
* tag 'imx-fixes-3.12' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx6q: fix the wrong offset of the Pad Mux register
ARM: imx: i.mx6d/q: disable the double linefill feature of PL310
ARM: imx51.dtsi: fix PATA device clock
ARM: mach-imx: clk-imx51-imx53: Fix 'spdif1_pred' clock registration
ARM: imx: initialize clk_init_data.flags for clk-fixup-mux
ARM: imx27.dtsi: fix CSPI PER clock id
Signed-off-by: Olof Johansson <olof@lixom.net>
Without this, legacy platforms that can boot with a multiplatform
kernel but that need the DTB to be appended, won't have a way to pass
firmware-set bootargs to the kernel.
This is needed to boot multi_v7_defconfig on snowball, for instance.
Signed-off-by: Olof Johansson <olof@lixom.net>
This fixes a multiplatform regression on the Ux500.
When compiling the Ux500 platforms in multiplatform configurations
both PL310_ERRATA_588369 and PL310_ERRATA_727915 would crash the
platform when trying to launch the init process.
The Ux500 cannot access the debug registers of the PL310, it will
just crash if you try this. So disable this by setting the debug
callback to NULL when initializing the l2x0 on this platform.
Cc: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
This fixes the following issue
BUG: using smp_processor_id() in preemptible [00000000] code: kjournald/1761
caller is blast_dcache32+0x30/0x254
Call Trace:
[<8047f02c>] dump_stack+0x8/0x34
[<802e7e40>] debug_smp_processor_id+0xe0/0xf0
[<80114d94>] blast_dcache32+0x30/0x254
[<80118484>] r4k_dma_cache_wback_inv+0x200/0x288
[<80110ff0>] mips_dma_map_sg+0x108/0x180
[<80355098>] ide_dma_prepare+0xf0/0x1b8
[<8034eaa4>] do_rw_taskfile+0x1e8/0x33c
[<8035951c>] ide_do_rw_disk+0x298/0x3e4
[<8034a3c4>] do_ide_request+0x2e0/0x704
[<802bb0dc>] __blk_run_queue+0x44/0x64
[<802be000>] queue_unplugged.isra.36+0x1c/0x54
[<802beb94>] blk_flush_plug_list+0x18c/0x24c
[<802bec6c>] blk_finish_plug+0x18/0x48
[<8026554c>] journal_commit_transaction+0x3b8/0x151c
[<80269648>] kjournald+0xec/0x238
[<8014ac00>] kthread+0xb8/0xc0
[<8010268c>] ret_from_kernel_thread+0x14/0x1c
Caches in most systems are identical - but not always, so we can't avoid
the use of smp_call_function() by just looking at the boot CPU's data,
have to fiddle with preemption instead.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5835
Pull more tile architecture updates from Chris Metcalf:
"This second batch of changes is just cleanup of various kinds from
doing some tidying work in the sources.
Some dead code is removed, comment typos fixed, whitespace and style
issues cleaned up, and some header updates from our internal
"upstream" architecture team"
* git://git.kernel.org/pub/scm/linux/kernel/git/cmetcalf/linux-tile:
tile: remove stray blank space
tile: <arch/> header updates from upstream
tile: improve gxio iorpc autogenerated code style
tile: double default VMALLOC space
tile: remove stale arch/tile/kernel/futex_64.S
tile: remove HUGE_VMAP dead code
tile: use pmd_pfn() instead of casting via pte_t
tile: fix typos in comment in arch/tile/kernel/unaligned.c
Fix the DTS data for ocp2scp node by adding the
missing reg property.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
USB3 block has a 64KiB space, another 64KiB is
used for the wrapper.
Without this change, resource_size() will get
confused and driver won't probe because size
will be negative.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The BeagleBone Black is basically a regular BeagleBone with eMMC and
HDMI added, so create a common dtsi both can use.
IMPORTANT: booting the existing am335x-bone.dts will blow up the HDMI
transceiver after a dozen boots with an uSD card inserted because LDO
will be at 3.3V instead of 1.8.
MMC support for AM335x still isn't in, so only the LDO change has been
added.
Signed-off-by: Koen Kooi <koen@dominion.thruhere.net>
Tested-by: Tom Rini <trini@ti.com>
Tested-by: Matt Porter <matt.porter@linaro.org>
Acked-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Tested-by: Joel Fernandes <joelf@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
The beagle and beagle-xm entries were inside the same double quote.
Split them to have two distinct entries.
Signed-off-by: Robert Nelson <robertcnelson@gmail.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>
boot_cpu_data is used the same as current_cpu_data but returns the CPU
data for CPU 0. This means it doesn't have to use smp_processor_id()
thus no need to disable preemption.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
After nested vmentry stale cache can be used to reload L2 PDPTR pointers
which will cause L2 guest to fail. Fix it by invalidating cache on nested
vmentry emulation.
https://bugzilla.kernel.org/show_bug.cgi?id=60830
Signed-off-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Page tables in a read-only memory slot will currently cause a triple
fault because the page walker uses gfn_to_hva and it fails on such a slot.
OVMF uses such a page table; however, real hardware seems to be fine with
that as long as the accessed/dirty bits are set. Save whether the slot
is readonly, and later check it when updating the accessed and dirty bits.
Reviewed-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
Opcode CA
This gets used by a DOS based NetWare guest.
Signed-off-by: Bruce Rogers <brogers@suse.com>
Reviewed-by: Gleb Natapov <gleb@redhat.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
The patch "0b7a76a ARM: dts: imx6q{dl}: add DTE pads for uart"
adds the DTE pads for uart. For PAD_EIM_D29, the offset of the
Pad Mux register should be 0x0c8, not 0x0c4.
This patch fixes it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The L2 cache controller(PL310) version on the i.MX6D/Q is r3p1-50rel0
The L2 cache controller(PL310) version on the i.MX6DL/SOLO/SL is r3p2
But according to ARM PL310 errata: 752271
ID: 752271: Double linefill feature can cause data corruption
Fault Status: Present in: r3p0, r3p1, r3p1-50rel0. Fixed in r3p2
Workaround: The only workaround to this erratum is to disable the
double linefill feature. This is the default behavior.
without this patch, you will meet the following error when run the
memtester application at: http://pyropus.ca/software/memtester/
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365664.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365668.
FAILURE: 0x00100000 != 0x00200000 at offset 0x0136566c.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365670.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365674.
FAILURE: 0x00100000 != 0x00200000 at offset 0x01365678.
Signed-off-by: Jason Liu <r64343@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Commit 718a350 (ARM: i.MX51: Add PATA support) adds pata support to the
imx51.dtsi file and is using clock 161. The problem is that the right
clock is 172, according to commit 5d530bb (ARM: i.MX5: Add PATA and SRTC
clocks). Using the clock 172 makes things work again (and kills a nasty
system freeze).
Tested-by: Steev Klimaszewski <steev@gentoo.org>
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Since commit beb2d1c1ba (ARM i.MX5: Add S/PDIF clocks), the following clock
error appears on mx51:
TrustZone Interrupt Controller (TZIC) initialized
i.MX51 clk 180: register failed with -17
i.MX5 clk 180: register failed with -17
sched_clock: 32 bits at 24MHz, resolution 41ns, wraps every 178956ms
CPU identified as i.MX51, silicon rev 3.0
...
Clock 180 corresponds to 'spdif1_podf' and this clock is getting registered
twice.
Fix it, by properly registering the 'spdif1_pred' clock, which should not
reference 'spdif1_podf'.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
The clk_init_data.flags of clk-fixup-mux is left there without
initialization. It may hold some random data and cause clock framework
interpret the clock in an unexpected way. At least on imx6sl, the
following division by zero error with sched_clock is seen because of it.
Division by zero in kernel.
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.11.0-rc3+ #19
Backtrace:
[<80011af0>] (dump_backtrace+0x0/0x10c) from [<80011c90>] (show_stack+0x18/0x1c)
r6:3b9aca00 r5:00000020 r4:00000000 r3:00000000
[<80011c78>] (show_stack+0x0/0x1c) from [<8055e02c>] (dump_stack+0x78/0x94)
[<8055dfb4>] (dump_stack+0x0/0x94) from [<80011924>] (__div0+0x18/0x20)
r4:00000000 r3:00000000
[<8001190c>] (__div0+0x0/0x20) from [<8026c408>] (Ldiv0_64+0x8/0x18)
[<8006330c>] (clocks_calc_mult_shift+0x0/0xf8) from [<8072f604>] (setup_sched_clock+0x88/0x1f0)
[<8072f57c>] (setup_sched_clock+0x0/0x1f0) from [<8071ad48>] (mxc_timer_init+0xe8/0x17c)
[<8071ac60>] (mxc_timer_init+0x0/0x17c) from [<807290b0>] (imx6sl_clocks_init+0x1db8/0x1dc0)
r8:807a9ca4 r7:00000000 r6:80777564 r5:8100c1f4 r4:c0820000
[<807272f8>] (imx6sl_clocks_init+0x0/0x1dc0) from [<807420ac>] (of_clk_init+0x40/0x6c)
[<8074206c>] (of_clk_init+0x0/0x6c) from [<807290cc>] (imx6sl_timer_init+0x14/0x18)
r5:807a8e80 r4:ffffffff
[<807290b8>] (imx6sl_timer_init+0x0/0x18) from [<80716e1c>] (time_init+0x24/0x34)
[<80716df8>] (time_init+0x0/0x34) from [<80713738>] (start_kernel+0x1b0/0x310)
[<80713588>] (start_kernel+0x0/0x310) from [<80008074>] (0x80008074)
r7:80770b08 r6:80754cd4 r5:8076c8c4 r4:10c53c7d
sched_clock: 32 bits at 0 Hz, resolution 0ns, wraps every 0ms
Fix the bug by initializing init.flags as zero.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Pull timer code update from Thomas Gleixner:
- armada SoC clocksource overhaul with a trivial merge conflict
- Minor improvements to various SoC clocksource drivers
* 'timers/core' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
clocksource: armada-370-xp: Add detailed clock requirements in devicetree binding
clocksource: armada-370-xp: Get reference fixed-clock by name
clocksource: armada-370-xp: Replace WARN_ON with BUG_ON
clocksource: armada-370-xp: Fix device-tree binding
clocksource: armada-370-xp: Introduce new compatibles
clocksource: armada-370-xp: Use CLOCKSOURCE_OF_DECLARE
clocksource: armada-370-xp: Simplify TIMER_CTRL register access
clocksource: armada-370-xp: Use BIT()
ARM: timer-sp: Set dynamic irq affinity
ARM: nomadik: add dynamic irq flag to the timer
clocksource: sh_cmt: 32-bit control register support
clocksource: em_sti: Convert to devm_* managed helpers
The hardware architecture descriptor headers have been updated, in
particular to reflect some larger MMIO fields on the mPIPE shims for
controlling the network hardware, from the recent Gx72 release.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
With per-cpu data as well as loaded kernel modules coming from
the vmalloc arena, we get close to the line all the time and
occasionally need more than we had, so just double it up by default.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Pull MIPS fixes from Ralf Baechle:
"These are four patches for three construction sites:
- Fix register decoding for the combination of multi-core processors
and multi-threading.
- Two more fixes that are part of the ongoing DECstation resurrection
work. One of these touches a DECstation-only network driver.
- Finally Markos' trivial build fix for the AP/SP support.
(With this applied now all MIPS defconfigs are building again)"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
MIPS: kernel: vpe: Make vpe_attrs an array of pointers.
MIPS: Fix SMP core calculations when using MT support.
MIPS: DECstation I/O ASIC DMA interrupt handling fix
MIPS: DECstation HRT initialization rearrangement
x86 chips with LPSS (low power subsystem) such as Lynxpoint and
Baytrail have SoC like peripheral support and controllable pins.
At the moment, Baytrail needs the pinctrl-baytrail driver to let
peripherals control their gpio resources, but more pincontrol
functions such as pin muxing and grouping are possible to add
later.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Link: http://lkml.kernel.org/r/1379080949-21734-1-git-send-email-mathias.nyman@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
On Intel SNB (SNB, SNB-EP), the event MEM_LOAD_UOPS_MISS_RETIRED
supports PEBS. It was missing for the SNB PEBS event constraint
table thereby preventing any measurement with PEBS for it.
This patch adds the event to the PEBS table for SNB.
WARNING: it should be noted that this event like a few others
are subject to the erratum BT241 for Xeon E5 (SNB-EP). As such,
the event may undercount when used with PEBS unless the
workaround is implemented. But without this patch and just the
workaround, the kernel would not allow precise sampling on this
event. BT241 is documented in:
http://www.intel.com/content/dam/www/public/us/en/documents/specification-updates/xeon-e5-family-spec-update.pdf
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: peterz@infradead.org
Cc: ak@linux.intel.com
Cc: zheng.z.yan@intel.com
Link: http://lkml.kernel.org/r/20130913201646.GA23981@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
A config option to allow a variant vmap() using huge pages that was never
upstreamed had some bits of code related to it scattered around the tile
architecture; the config option was removed downstream and this commit
cleans up the scattered evidence of it from the upstream as well.
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com>
Pull generic hardirq option removal from Martin Schwidefsky:
"All architectures now use generic hardirqs, s390 has been last to
switch.
With that the code under !CONFIG_GENERIC_HARDIRQS and the related
HAVE_GENERIC_HARDIRQS and GENERIC_HARDIRQS config options can be
removed. Yay!"
* 'genirq' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
Remove GENERIC_HARDIRQ config option
Commit 567b21e973
"mips: convert vpe_class to use dev_groups"
broke the build on MIPS since vpe_attrs should be an array
of 'struct device_attribute' pointers.
Fixes the following build problem:
arch/mips/kernel/vpe.c:1372:2: error: missing braces around initializer
[-Werror=missing-braces]
arch/mips/kernel/vpe.c:1372:2: error: (near initialization for 'vpe_attrs[0]')
[-Werror=missing-braces]
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: John Crispin <blogic@openwrt.org>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5819/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
After the last architecture switched to generic hard irqs the config
options HAVE_GENERIC_HARDIRQS & GENERIC_HARDIRQS and the related code
for !CONFIG_GENERIC_HARDIRQS can be removed.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The TCBIND register is only available if the core has MT support. It
should not be read otherwise. Secondly, the number of TCs (siblings)
are calculated differently depending on if the kernel is configured
as SMVP or SMTC.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5822/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
This change complements commit d0da7c002f7b2a93582187a9e3f73891a01d8ee4
and brings clear_ioasic_irq back, renaming it to clear_ioasic_dma_irq at
the same time, to make I/O ASIC DMA interrupts functional.
Unlike ordinary I/O ASIC interrupts DMA interrupts need to be deasserted
by software by writing 0 to the respective bit in I/O ASIC's System
Interrupt Register (SIR), similarly to how CP0.Cause.IP0 and CP0.Cause.IP1
bits are handled in the CPU (the difference is SIR DMA interrupt bits are
R/W0C so there's no need for an RMW cycle). Otherwise the handler is
reentered over and over again.
The only current user is the DEC LANCE Ethernet driver and its extremely
uncommon DMA memory error handler that does not care when exactly the
interrupt is cleared. Anticipating the use of DMA interrupts by the Zilog
SCC driver this change however exports clear_ioasic_dma_irq for device
drivers to choose the right application-specific sequence to clear the
request explicitly rather than calling it implicitly in the .irq_eoi
handler of `struct irq_chip'. Previously these interrupts were cleared in
the .end handler of the said structure, before it was removed.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5826/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Not all I/O ASIC versions have the free-running counter implemented, an
early revision used in the 5000/1xx models aka 3MIN and 4MIN did not have
it. Therefore we cannot unconditionally use it as a clock source.
Fortunately if not implemented its register slot has a fixed value so it
is enough if we check for the value at the end of the calibration period
being the same as at the beginning.
This also means we need to look for another high-precision clock source on
the systems affected. The 5000/1xx can have an R4000SC processor
installed where the CP0 Count register can be used as a clock source.
Unfortunately all the R4k DECstations suffer from the missed timer
interrupt on CP0 Count reads erratum, so we cannot use the CP0 timer as a
clock source and a clock event both at a time. However we never need an
R4k clock event device because all DECstations have a DS1287A RTC chip
whose periodic interrupt can be used as a clock source.
This gives us the following four configuration possibilities for I/O ASIC
DECstations:
1. No I/O ASIC counter and no CP0 timer, e.g. R3k 5000/1xx (3MIN).
2. No I/O ASIC counter but the CP0 timer, i.e. R4k 5000/150 (4MIN).
3. The I/O ASIC counter but no CP0 timer, e.g. R3k 5000/240 (3MAX+).
4. The I/O ASIC counter and the CP0 timer, e.g. R4k 5000/260 (4MAX+).
For #1 and #2 this change stops the I/O ASIC free-running counter from
being installed as a clock source of a 0Hz frequency. For #2 it also
arranges for the CP0 timer to be used as a clock source rather than a
clock event device, because having an accurate wall clock is more
important than a high-precision interval timer. For #3 there is no
change. For #4 the change makes the I/O ASIC free-running counter
installed as a clock source so that the CP0 timer can be used as a clock
event device.
Unfortunately the use of the CP0 timer as a clock event device relies on a
succesful completion of c0_compare_interrupt. That never happens, because
while waiting for a CP0 Compare interrupt to happen the function spins in
a loop reading the CP0 Count register. This makes the CP0 Count erratum
trigger reliably causing the interrupt waited for to be lost in all cases.
As a result #4 resorts to using the CP0 timer as a clock source as well,
just as #2. However we want to keep this separate arrangement in case
(hope) c0_compare_interrupt is eventually rewritten such that it avoids
the erratum.
Signed-off-by: Maciej W. Rozycki <macro@linux-mips.org>
Cc: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/5825/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
We have the build infrastructure to generate uImages so we should ignore
the resulting generated files.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Mike Frysinger <vapier@gentoo.org>
- Enable GMAC
- Set propler DMA PBL
- Disable DMA store and forward mode
- Select PTP input clock from MII
clock.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>
If SCB exists in select blackfin cpu, developer can change the SCB
priority in kernel configuration.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Steven Miao <realmz6@gmail.com>
Pull MIPS updates from Ralf Baechle:
"This has been sitting in -next for a while with no objections and all
MIPS defconfigs except one are building fine; that one platform got
broken by another patch in your tree and I'm going to submit a patch
separately.
- a handful of fixes that didn't make 3.11
- a few bits of Octeon 3 support with more to come for a later
release
- platform enhancements for Octeon, ath79, Lantiq, Netlogic and
Ralink SOCs
- a GPIO driver for the Octeon
- some dusting off of the DECstation code
- the usual dose of cleanups"
* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus: (65 commits)
MIPS: DMA: Fix BUG due to smp_processor_id() in preemptible code
MIPS: kexec: Fix random crashes while loading crashkernel
MIPS: kdump: Skip walking indirection page for crashkernels
MIPS: DECstation HRT calibration bug fixes
MIPS: Export copy_from_user_page() (needed by lustre)
MIPS: Add driver for the built-in PCI controller of the RT3883 SoC
MIPS: DMA: For BMIPS5000 cores flush region just like non-coherent R10000
MIPS: ralink: Add support for reset-controller API
MIPS: ralink: mt7620: Add cpu-feature-override header
MIPS: ralink: mt7620: Add spi clock definition
MIPS: ralink: mt7620: Add wdt clock definition
MIPS: ralink: mt7620: Improve clock frequency detection
MIPS: ralink: mt7620: This SoC has EHCI and OHCI hosts
MIPS: ralink: mt7620: Add verbose ram info
MIPS: ralink: Probe clocksources from OF
MIPS: ralink: Add support for systick timer found on newer ralink SoC
MIPS: ralink: Add support for periodic timer irq
MIPS: Netlogic: Built-in DTB for XLP2xx SoC boards
MIPS: Netlogic: Add support for USB on XLP2xx
MIPS: Netlogic: XLP2xx update for I2C controller
...
Merge more patches from Andrew Morton:
"The rest of MM. Plus one misc cleanup"
* emailed patches from Andrew Morton <akpm@linux-foundation.org>: (35 commits)
mm/Kconfig: add MMU dependency for MIGRATION.
kernel: replace strict_strto*() with kstrto*()
mm, thp: count thp_fault_fallback anytime thp fault fails
thp: consolidate code between handle_mm_fault() and do_huge_pmd_anonymous_page()
thp: do_huge_pmd_anonymous_page() cleanup
thp: move maybe_pmd_mkwrite() out of mk_huge_pmd()
mm: cleanup add_to_page_cache_locked()
thp: account anon transparent huge pages into NR_ANON_PAGES
truncate: drop 'oldsize' truncate_pagecache() parameter
mm: make lru_add_drain_all() selective
memcg: document cgroup dirty/writeback memory statistics
memcg: add per cgroup writeback pages accounting
memcg: check for proper lock held in mem_cgroup_update_page_stat
memcg: remove MEMCG_NR_FILE_MAPPED
memcg: reduce function dereference
memcg: avoid overflow caused by PAGE_ALIGN
memcg: rename RESOURCE_MAX to RES_COUNTER_MAX
memcg: correct RESOURCE_MAX to ULLONG_MAX
mm: memcg: do not trap chargers with full callstack on OOM
mm: memcg: rework and document OOM waiting and wakeup
...
The x86 fault handler bails in the middle of error handling when the
task has a fatal signal pending. For a subsequent patch this is a
problem in OOM situations because it relies on pagefault_out_of_memory()
being called even when the task has been killed, to perform proper
per-task OOM state unwinding.
Shortcutting the fault like this is a rather minor optimization that
saves a few instructions in rare cases. Just remove it for
user-triggered faults.
Use the opportunity to split the fault retry handling from actual fault
errors and add locking documentation that reads suprisingly similar to
ARM's.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: azurIt <azurit@pobox.sk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Unlike global OOM handling, memory cgroup code will invoke the OOM killer
in any OOM situation because it has no way of telling faults occuring in
kernel context - which could be handled more gracefully - from
user-triggered faults.
Pass a flag that identifies faults originating in user space from the
architecture-specific fault handlers to generic code so that memcg OOM
handling can be improved.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Cc: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: azurIt <azurit@pobox.sk>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Kernel faults are expected to handle OOM conditions gracefully (gup,
uaccess etc.), so they should never invoke the OOM killer. Reserve this
for faults triggered in user context when it is the only option.
Most architectures already do this, fix up the remaining few.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: azurIt <azurit@pobox.sk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The memcg code can trap tasks in the context of the failing allocation
until an OOM situation is resolved. They can hold all kinds of locks
(fs, mm) at this point, which makes it prone to deadlocking.
This series converts memcg OOM handling into a two step process that is
started in the charge context, but any waiting is done after the fault
stack is fully unwound.
Patches 1-4 prepare architecture handlers to support the new memcg
requirements, but in doing so they also remove old cruft and unify
out-of-memory behavior across architectures.
Patch 5 disables the memcg OOM handling for syscalls, readahead, kernel
faults, because they can gracefully unwind the stack with -ENOMEM. OOM
handling is restricted to user triggered faults that have no other
option.
Patch 6 reworks memcg's hierarchical OOM locking to make it a little
more obvious wth is going on in there: reduce locked regions, rename
locking functions, reorder and document.
Patch 7 implements the two-part OOM handling such that tasks are never
trapped with the full charge stack in an OOM situation.
This patch:
Back before smart OOM killing, when faulting tasks were killed directly on
allocation failures, the arch-specific fault handlers needed special
protection for the init process.
Now that all fault handlers call into the generic OOM killer (see commit
609838cfed97: "mm: invoke oom-killer from remaining unconverted page
fault handlers"), which already provides init protection, the
arch-specific leftovers can be removed.
Signed-off-by: Johannes Weiner <hannes@cmpxchg.org>
Reviewed-by: Michal Hocko <mhocko@suse.cz>
Acked-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: David Rientjes <rientjes@google.com>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: azurIt <azurit@pobox.sk>
Acked-by: Vineet Gupta <vgupta@synopsys.com> [arch/arc bits]
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull vfs pile 4 from Al Viro:
"list_lru pile, mostly"
This came out of Andrew's pile, Al ended up doing the merge work so that
Andrew didn't have to.
Additionally, a few fixes.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: (42 commits)
super: fix for destroy lrus
list_lru: dynamically adjust node arrays
shrinker: Kill old ->shrink API.
shrinker: convert remaining shrinkers to count/scan API
staging/lustre/libcfs: cleanup linux-mem.h
staging/lustre/ptlrpc: convert to new shrinker API
staging/lustre/obdclass: convert lu_object shrinker to count/scan API
staging/lustre/ldlm: convert to shrinkers to count/scan API
hugepage: convert huge zero page shrinker to new shrinker API
i915: bail out earlier when shrinker cannot acquire mutex
drivers: convert shrinkers to new count/scan API
fs: convert fs shrinkers to new scan/count API
xfs: fix dquot isolation hang
xfs-convert-dquot-cache-lru-to-list_lru-fix
xfs: convert dquot cache lru to list_lru
xfs: rework buffer dispose list tracking
xfs-convert-buftarg-lru-to-generic-code-fix
xfs: convert buftarg LRU to generic code
fs: convert inode and dentry shrinking to be node aware
vmscan: per-node deferred work
...
A small batch of fixes that have trickled in over the last week of the
merge window.
Also included are few small devicetree updates for sunxi, since it
enables me to use one of their newer boards (cubieboard2) for additional
test coverage. The support for that SoC is new for 3.12, so there's no
exposure to new regressions due to it.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=HLjK
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"A small batch of fixes that have trickled in over the last week of the
merge window.
Also included are few small devicetree updates for sunxi, since it
enables me to use one of their newer boards (cubieboard2) for
additional test coverage. The support for that SoC is new for 3.12,
so there's no exposure to new regressions due to it"
* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: sun7i: olinuxino-micro: Enable the EMAC
ARM: dts: sun7i: cubieboard2: Enable the EMAC
ARM: dts: sun7i: Add the muxing options for the EMAC
ARM: dts: sun7i: Enable the Ethernet in the A20
i2c: davinci: Fix bad dev_get_platdata() conversion
ARM: vexpress: allow dcscb and tc2_pm in a combined ARMv6+v7 build
ARM: shmobile: lager: Do not use register_type field of struct sh_eth_plat_data
ARM: pxa: ssp: Check return values from phandle lookups
ARM: PCI: versatile: Fix SMAP register offsets
ARM: PCI: versatile: Fix PCI I/O
ARM: PCI: versatile: Fix map_irq function to match hardware
ARM: ep93xx: Don't use modem interface on the second UART
ARM: shmobile: r8a7779: Update early timer initialisation order
Pull ARM fixes from Russell King:
"Just two fixes here - one for the recent addition of Neon stuff which
causes problems when this is built as a module. The other was one
spotted by Olof with the fixed-HZ stuff.
Last patch (which is at the very top) is not a fix per-se, but an
almost-end-of-merge window sorting of the select symbols in
arch/arm/Kconfig to keep them as akpm would like to reduce unnecessary
conflicts. I've also taken the liberty this time to add a comment at
the end to discourage the endless "add the next select to the bottom
of a nicely sorted list" syndrome"
* 'fixes' of git://git.linaro.org/people/rmk/linux-arm:
ARM: sort arch/arm/Kconfig
ARM: fix forced-HZ values
ARM: 7835/2: fix modular build of xor_blocks() with NEON enabled
Keep arch/arm/Kconfig select statements sorted alphabetically. I've
added a comment at the bottom of the main bank for CONFIG_ARM to this
effect so hopefully this will keep things more in order.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The A20-olinuxino-micro has the EMAC wired in. Enable it in the DT so
that we can use it.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Cubieboard2, just like its A10 counterpart, has the Ethernet wired
in. Enable it in the DT.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The A20 has several muxing options for the EMAC. Yet, the currently
supported boards only use one set of them. Add that pin set to the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
The Allwinner A20 SoC also have the EMAC found on the A10 and A10s.
Enable the support for it in the DTSI.
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
This round the updates contain:
* A new driver for the Freescale PAMU IOMMU from Varun Sethi.
This driver has cooked for a while and required changes to the
IOMMU-API and infrastructure that were already merged before.
* Updates for the ARM-SMMU driver from Will Deacon
* Various fixes, the most important one is probably a fix from
Alex Williamson for a memory leak in the VT-d page-table
freeing code
In summary not all that much. The biggest part in the diffstat is the
new PAMU driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=UZoD
-----END PGP SIGNATURE-----
Merge tag 'iommu-updates-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU Updates from Joerg Roedel:
"This round the updates contain:
- A new driver for the Freescale PAMU IOMMU from Varun Sethi.
This driver has cooked for a while and required changes to the
IOMMU-API and infrastructure that were already merged before.
- Updates for the ARM-SMMU driver from Will Deacon
- Various fixes, the most important one is probably a fix from Alex
Williamson for a memory leak in the VT-d page-table freeing code
In summary not all that much. The biggest part in the diffstat is the
new PAMU driver"
* tag 'iommu-updates-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
intel-iommu: Fix leaks in pagetable freeing
iommu/amd: Fix resource leak in iommu_init_device()
iommu/amd: Clean up unnecessary MSI/MSI-X capability find
iommu/arm-smmu: Simplify VMID and ASID allocation
iommu/arm-smmu: Don't use VMIDs for stage-1 translations
iommu/arm-smmu: Tighten up global fault reporting
iommu/arm-smmu: Remove broken big-endian check
iommu/fsl: Remove unnecessary 'fsl-pamu' prefixes
iommu/fsl: Fix whitespace problems noticed by git-am
iommu/fsl: Freescale PAMU driver and iommu implementation.
iommu/fsl: Add additional iommu attributes required by the PAMU driver.
powerpc: Add iommu domain pointer to device archdata
iommu/exynos: Remove dead code (set_prefbuf)
Pull perf fixes from Ingo Molnar:
"Various fixes.
The -g perf report lockup you reported is only partially addressed,
patches that fix the excessive runtime are still being worked on"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/x86: Fix uncore PCI fixed counter handling
uprobes: Fix utask->depth accounting in handle_trampoline()
perf/x86: Add constraint for IVB CYCLE_ACTIVITY:CYCLES_LDM_PENDING
perf: Fix up MMAP2 buffer space reservation
perf tools: Add attr->mmap2 support
perf kvm: Fix sample_type manipulation
perf evlist: Fix id pos in perf_evlist__open()
perf trace: Handle perf.data files with no tracepoints
perf session: Separate progress bar update when processing events
perf trace: Check if MAP_32BIT is defined
perf hists: Fix formatting of long symbol names
perf evlist: Fix parsing with no sample_id_all bit set
perf tools: Add test for parsing with no sample_id_all bit
perf trace: Check control+C more often
Commit 05b016ecf5 "ARC: Setup Vector Table Base in early boot" moved
the Interrupt vector Table setup out of arc_init_IRQ() which is called
for all CPUs, to entry point of boot cpu only, breaking booting of others.
Fix by adding the same to entry point of non-boot CPUs too.
read_arc_build_cfg_regs() printing IVT Base Register didn't help the
casue since it prints a synthetic value if zero which is totally bogus,
so fix that to print the exact Register.
[vgupta: Remove the now stale comment from header of arc_init_IRQ and
also added the commentary for halt-on-reset]
Cc: Gilad Ben-Yossef <gilad@benyossef.com>
Cc: Cc: <stable@vger.kernel.org> #3.11
Signed-off-by: Noam Camus <noamc@ezchip.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
There was a bug in the handling of SNB-EP/IVB-EP uncore PCI
fixed counters, e.g., IMC.
It would cause erratic values to be returned for the IMC
clockticks event. This was due to a bogus hwc->config value
which was then written to PCI config space.
The erratic values can be seen via:
$ perf stat -a -C 0 -e uncore_imc_0/clockticks/ -I 1000 sleep 10
The fixed counter has most fields marked as reserved with
hw reset values of 0. Yet the kernel was defaulting to a
hwc->config = ~0 and that was causing the issues.
This patch sets the hwc->config values for fixed uncore event
to 0. Now, the values of IMC clockticks is correct.
Signed-off-by: Stephane Eranian <eranian@google.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
Cc: peterz@infradead.org
Cc: zheng.z.yan@intel.com
Link: http://lkml.kernel.org/r/20130909195350.GA17643@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The IvyBridge event CYCLE_ACTIVITY:CYCLES_LDM_PENDING can only
be measured on counters 0-3 when HT is off. When HT is on, you
only have counters 0-3.
If you program it on the eight counters for 1s on a 3GHz
IVB laptop running a noploop, you see:
2 747 527 CYCLE_ACTIVITY:CYCLES_LDM_PENDING
2 747 527 CYCLE_ACTIVITY:CYCLES_LDM_PENDING
2 747 527 CYCLE_ACTIVITY:CYCLES_LDM_PENDING
2 747 527 CYCLE_ACTIVITY:CYCLES_LDM_PENDING
3 280 563 608 CYCLE_ACTIVITY:CYCLES_LDM_PENDING
3 280 563 608 CYCLE_ACTIVITY:CYCLES_LDM_PENDING
3 280 563 608 CYCLE_ACTIVITY:CYCLES_LDM_PENDING
3 280 563 608 CYCLE_ACTIVITY:CYCLES_LDM_PENDING
Clearly the last 4 values are bogus.
Signed-off-by: Stephane Eranian <eranian@google.com>
Cc: peterz@infradead.org
Cc: ak@linux.intel.com
Cc: zheng.z.yan@intel.com
Cc: dhsharp@google.com
Link: http://lkml.kernel.org/r/20130911152222.GA28761@google.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Modify the s390 copy_oldmem_page() and remap_oldmem_pfn_range() function
for zfcpdump to read from the HSA memory if memory below HSA_SIZE bytes is
requested. Otherwise real memory is used.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Willeke <willeke@de.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Introduce the s390 specific way to map pages from oldmem. The memory area
below OLDMEM_SIZE is mapped with offset OLDMEM_BASE. The other old memory
is mapped directly.
Signed-off-by: Jan Willeke <willeke@de.ibm.com>
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Exchange the old relocate mechanism with the new arch function call
override mechanism that allows to create the ELF core header in the 2nd
kernel.
Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com>
Cc: HATAYAMA Daisuke <d.hatayama@jp.fujitsu.com>
Cc: Jan Willeke <willeke@de.ibm.com>
Cc: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With the general-instruction extension facility (z10) a couple of
instructions with a pc-relative long displacement were introduced. The
kprobes support for these instructions however was never implemented.
In result, if anybody ever put a probe on any of these instructions the
result would have been random behaviour after the instruction got executed
within the insn slot.
So lets add the missing handling for these instructions. Since all of the
new instructions have 32 bit signed displacement the easiest solution is
to allocate an insn slot that is within the same 2GB area like the
original instruction and patch the displacement field.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Reviewed-by: Masami Hiramatsu <masami.hiramatsu.pt@hitachi.com>
Cc: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I found the following pattern that leads in to interesting findings:
grep -r "ret.*|=.*__put_user" *
grep -r "ret.*|=.*__get_user" *
grep -r "ret.*|=.*__copy" *
The __put_user() calls in compat_ioctl.c, ptrace compat, signal compat,
since those appear in compat code, we could probably expect the kernel
addresses not to be reachable in the lower 32-bit range, so I think they
might not be exploitable.
For the "__get_user" cases, I don't think those are exploitable: the worse
that can happen is that the kernel will copy kernel memory into in-kernel
buffers, and will fail immediately afterward.
The alpha csum_partial_copy_from_user() seems to be missing the
access_ok() check entirely. The fix is inspired from x86. This could
lead to information leak on alpha. I also noticed that many architectures
map csum_partial_copy_from_user() to csum_partial_copy_generic(), but I
wonder if the latter is performing the access checks on every
architectures.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Matt Turner <mattst88@gmail.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
_PAGE_SOFT_DIRTY bit should never be set on present pte so add VM_BUG_ON
to catch any potential future abuse.
Also add a comment on _PAGE_SWP_SOFT_DIRTY definition explaining scope of
its usage.
Signed-off-by: Cyrill Gorcunov <gorcunov@openvz.org>
Acked-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Currently hugepage migration works well only for pmd-based hugepages
(mainly due to lack of testing,) so we had better not enable migration of
other levels of hugepages until we are ready for it.
Some users of hugepage migration (mbind, move_pages, and migrate_pages) do
page table walk and check pud/pmd_huge() there, so they are safe. But the
other users (softoffline and memory hotremove) don't do this, so without
this patch they can try to migrate unexpected types of hugepages.
To prevent this, we introduce hugepage_migration_support() as an
architecture dependent check of whether hugepage are implemented on a pmd
basis or not. And on some architecture multiple sizes of hugepages are
available, so hugepage_migration_support() also checks hugepage size.
Signed-off-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: Hillf Danton <dhillf@gmail.com>
Cc: Wanpeng Li <liwanp@linux.vnet.ibm.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Hugh Dickins <hughd@google.com>
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Cc: Michal Hocko <mhocko@suse.cz>
Cc: Rik van Riel <riel@redhat.com>
Cc: "Aneesh Kumar K.V" <aneesh.kumar@linux.vnet.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The previous patch doing vmstats for TLB flushes ("mm: vmstats: tlb flush
counters") effectively missed UP since arch/x86/mm/tlb.c is only compiled
for SMP.
UP systems do not do remote TLB flushes, so compile those counters out on
UP.
arch/x86/kernel/cpu/mtrr/generic.c calls __flush_tlb() directly. This is
probably an optimization since both the mtrr code and __flush_tlb() write
cr4. It would probably be safe to make that a flush_tlb_all() (and then
get these statistics), but the mtrr code is ancient and I'm hesitant to
touch it other than to just stick in the counters.
[akpm@linux-foundation.org: tweak comments]
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
I was investigating some TLB flush scaling issues and realized that we do
not have any good methods for figuring out how many TLB flushes we are
doing.
It would be nice to be able to do these in generic code, but the
arch-independent calls don't explicitly specify whether we actually need
to do remote flushes or not. In the end, we really need to know if we
actually _did_ global vs. local invalidations, so that leaves us with few
options other than to muck with the counters from arch-specific code.
Signed-off-by: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pull more s390 updates from Heiko Carstens:
"This includes one bpf/jit bug fix where the jit compiler could
sometimes write generated code out of bounds of the allocated memory
area.
The rest of the patches are only cleanups and minor improvements"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux:
s390/irq: reduce size of external interrupt handler hash array
s390/compat,uid16: use current_cred()
s390/ap_bus: use and-mask instead of a cast
s390/ftrace: avoid pointer arithmetics with function pointers
s390: make various functions static, add declarations to header files
s390/compat signal: add couple of __force annotations
s390/mm: add __releases()/__acquires() annotations to gmap_alloc_table()
s390: keep Kconfig sorted
s390/irq: rework irq subclass handling
s390/irq: use hlists for external interrupt handler array
s390/dumpstack: convert print_symbol to %pSR
s390/perf: Remove print_hex_dump_bytes() debug output
s390: update defconfig
s390/bpf,jit: fix address randomization
Pull powerpc fixes from Ben Herrenschmidt:
"Here are a handful of small powerpc fixes.
A couple of section mismatches (always worth fixing), a missing export
of a new symbol causing build failures of modules, a page fault
deadlock fix (interestingly that bug has been around for a LONG time,
though it seems to be more easily triggered by KVM) and fixing pseries
default idle loop in the absence of the cpuidle drivers (such as
during boot)"
* 'merge' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc:
powerpc: Default arch idle could cede processor on pseries
fbdev/ps3fb: Fix section mismatch warning for ps3fb_probe
powerpc: Fix section mismatch warning for prom_rtas_call
powerpc: Fix possible deadlock on page fault
powerpc: Export cpu_to_chip_id() to fix build error
- Boot on ARM without using Xen unconditionally
- On Xen ARM don't run cpuidle/cpufreq
- Fix regression in balloon driver, preempt count warnings
- Fixes to make PVHVM able to use pv ticketlock.
- Revert Xen PVHVM disabling pv ticketlock (aka, re-enable pv ticketlocks)
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSLhcPAAoJEFjIrFwIi8fJGq8IAIxI9zcnY9N6eaD3DepdZlz9
AMT8/k7afau1rDMk5r3HaUjAkdeEvCgeWw8W6tJ+OK19AmFTVEvoO803MSzYkDol
6XoknSoU9UnE+/w4FF1FttWmRxkZ8Op/hcs9435q7o+L0zlk9CbbkxFlzUKf5yVD
KfvQED4D/ShmPj2f+jYLCtsIi1m/AJ36BsfaUtJo3QVKvJIFFbT6F1AJ4tlbmvC0
FOaHYl9cTlPXfrpwviIP0+W8RVmcWreLqSOKsdHuWzB//MSvZDVmLGc7JPorblfe
cuME/tF/Y5bnxHKp8Es2MczpdvS6yp/HNoe0g6AdLVPL7dvGPqKpf2uZZNXUawQ=
=qpSg
-----END PGP SIGNATURE-----
Merge tag 'stable/for-linus-3.12-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip
Pull Xen bug-fixes from Konrad Rzeszutek Wilk:
"This pull I usually do after rc1 is out but because we have a nice
amount of fixes, some bootup related fixes for ARM, and it is early in
the cycle we figured to do it now to help with tracking of potential
regressions.
The simple ones are the ARM ones - one of the patches fell through the
cracks, other fixes a bootup issue (unconditionally using Xen
functions). Then a fix for a regression causing preempt count being
off (patch causing this went in v3.12).
Lastly are the fixes to make Xen PVHVM guests use PV ticketlocks (Xen
PV already does).
The enablement of that was supposed to be part of the x86 spinlock
merge in commit 816434ec4a ("The biggest change here are
paravirtualized ticket spinlocks (PV spinlocks), which bring a nice
speedup on various benchmarks...") but unfortunatly it would cause
hang when booting Xen PVHVM guests. Yours truly got all of the bugs
fixed last week and they (six of them) are included in this pull.
Bug-fixes:
- Boot on ARM without using Xen unconditionally
- On Xen ARM don't run cpuidle/cpufreq
- Fix regression in balloon driver, preempt count warnings
- Fixes to make PVHVM able to use pv ticketlock.
- Revert Xen PVHVM disabling pv ticketlock (aka, re-enable pv ticketlocks)"
* tag 'stable/for-linus-3.12-rc0-tag-two' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
xen/spinlock: Don't use __initdate for xen_pv_spin
Revert "xen/spinlock: Disable IRQ spinlock (PV) allocation on PVHVM"
xen/spinlock: Don't setup xen spinlock IPI kicker if disabled.
xen/smp: Update pv_lock_ops functions before alternative code starts under PVHVM
xen/spinlock: We don't need the old structure anymore
xen/spinlock: Fix locking path engaging too soon under PVHVM.
xen/arm: disable cpuidle and cpufreq when linux is running as dom0
xen/p2m: Don't call get_balloon_scratch_page() twice, keep interrupts disabled for multicalls
ARM: xen: only set pm function ptrs for Xen guests
Pull drm fixes from Dave Airlie:
"Daniel had some fixes queued up, that were delayed, the stolen memory
ones and vga arbiter ones are quite useful, along with his usual bunch
of stuff, nothing for HSW outputs yet.
The one nouveau fix is for a regression I caused with the poweroff stuff"
* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (30 commits)
drm/nouveau: fix oops on runtime suspend/resume
drm/i915: Delay disabling of VGA memory until vgacon->fbcon handoff is done
drm/i915: try not to lose backlight CBLV precision
drm/i915: Confine page flips to BCS on Valleyview
drm/i915: Skip stolen region initialisation if none is reserved
drm/i915: fix gpu hang vs. flip stall deadlocks
drm/i915: Hold an object reference whilst we shrink it
drm/i915: fix i9xx_crtc_clock_get for multiplied pixels
drm/i915: handle sdvo input pixel multiplier correctly again
drm/i915: fix hpd work vs. flush_work in the pageflip code deadlock
drm/i915: fix up the relocate_entry refactoring
drm/i915: Fix pipe config warnings when dealing with LVDS fixed mode
drm/i915: Don't call sg_free_table() if sg_alloc_table() fails
i915: Update VGA arbiter support for newer devices
vgaarb: Fix VGA decodes changes
vgaarb: Don't disable resources that are not owned
drm/i915: Pin pages whilst mapping the dma-buf
drm/i915: enable trickle feed on Haswell
x86: add early quirk for reserving Intel graphics stolen memory v5
drm/i915: split PCI IDs out into i915_drm.h v4
...
Pull x86 jumplabel changes from Peter Anvin:
"One more x86 tree for this merge window. This tree improves the
handling of jump labels, so that most of the time we don't have to do
a massive initial patching run.
Furthermore, we will error out of the jump label is not what is
expected, eg if it has been corrupted or tampered with"
* 'x86/jumplabel' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/jump-label: Show where and what was wrong on errors
x86/jump-label: Add safety checks to jump label conversions
x86/jump-label: Do not bother updating nops if they are correct
x86/jump-label: Use best default nops for inital jump label calls
From Ryan Mallon, a fix for ep93xx.
* tag 'ep93xx-fixes-for-3.12' of git://github.com/RyanMallon/linux-ep93xx:
ARM: ep93xx: Don't use modem interface on the second UART
Signed-off-by: Olof Johansson <olof@lixom.net>
When adding cpuidle support to pSeries, we introduced two
regressions:
- The new cpuidle backend driver only works under hypervisors
supporting the "SLPLAR" option, which isn't the case of the
old POWER4 hypervisor and the HV "light" used on js2x blades
- The cpuidle driver registers fairly late, meaning that for
a significant portion of the boot process, we end up having
all threads spinning. This slows down the boot process and
increases the overall resource usage if the hypervisor has
shared processors.
This fixes both by implementing a "default" idle that will cede
to the hypervisor when possible, in a very simple way without
all the bells and whisles of cpuidle.
Reported-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Vaidyanathan Srinivasan <svaidy@linux.vnet.ibm.com>
Acked-by: Deepthi Dharwar <deepthi@linux.vnet.ibm.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
CC: <stable@vger.kernel.org>
While cross-building for PPC64 I've got
WARNING: vmlinux.o(.text.unlikely+0x1ba): Section mismatch in
reference from the function .prom_rtas_call() to the variable
.init.data:dt_string_start The function .prom_rtas_call() references
the variable __initdata dt_string_start. This is often because
.prom_rtas_call lacks a __initdata annotation or the annotation of
dt_string_start is wrong.
WARNING: vmlinux.o(.meminit.text+0xeb0): Section mismatch in reference
from the function .free_area_init_core.isra.47() to the function
.init.text:.set_pageblock_order() The function __meminit
.free_area_init_core.isra.47() references a function __init
.set_pageblock_order(). If .set_pageblock_order is only used by
.free_area_init_core.isra.47 then annotate .set_pageblock_order with a
matching annotation.
Fix it by proper annotation of prom_rtas_call.
Signed-off-by: Vladimir Murzin <murzin.v@gmail.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
powerpc allmodconfig build fails with:
ERROR: ".cpu_to_chip_id" [drivers/block/mtip32xx/mtip32xx.ko] undefined!
The problem was introduced with commit 15863ff3b (powerpc: Make chip-id
information available to userspace).
Export the missing symbol.
Cc: Vasant Hegde <hegdevasant@linux.vnet.ibm.com>
Cc: Shivaprasad G Bhat <sbhat@linux.vnet.ibm.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Convert the remaining couple of random shrinkers in the tree to the new
API.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Signed-off-by: Glauber Costa <glommer@openvz.org>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: J. Bruce Fields <bfields@redhat.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
Cc: Arve Hjønnevåg <arve@android.com>
Cc: Carlos Maiolino <cmaiolino@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Chuck Lever <chuck.lever@oracle.com>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: David Rientjes <rientjes@google.com>
Cc: Gleb Natapov <gleb@redhat.com>
Cc: Greg Thelen <gthelen@google.com>
Cc: J. Bruce Fields <bfields@redhat.com>
Cc: Jan Kara <jack@suse.cz>
Cc: Jerome Glisse <jglisse@redhat.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Cc: Marcelo Tosatti <mtosatti@redhat.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Thomas Hellstrom <thellstrom@vmware.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Olof Johansson reports that the tests against HZ_FIXED seem
non-functional. Fix this by using '0' as a sentinel for "not
specified" and test against that instead.
Reported-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The mn10300 kernel crashes just after starting userspace programs, if
CONFIG_PREEMPT is disabled:
Freeing unused kernel memory: 96K (90286000 - 9029e000)
MISALIGN: 97c33ff9: unsupported instruction f
MISALIGN: 97c33ff9: unsupported instruction f
MISALIGN: 97c33ff9: unsupported instruction f
:
This fixes the problem that was introduced by commit d17fc238ac
("MN10300: Enable IRQs more in system call exit work path").
Signed-off-by: Akira Takeuchi <takeuchi.akr@jp.panasonic.com>
Signed-off-by: Kiyoshi Owada <owada.kiyoshi@jp.panasonic.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Generally minor changes. A bunch of bug fixes, particularly for
initialization and some refactoring. Most notable change if feeding the
entire flattened tree into the random pool at boot. May not be
significant, but shouldn't hurt either.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=GSWl
-----END PGP SIGNATURE-----
Merge tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux
Pull device tree core updates from Grant Likely:
"Generally minor changes. A bunch of bug fixes, particularly for
initialization and some refactoring. Most notable change if feeding
the entire flattened tree into the random pool at boot. May not be
significant, but shouldn't hurt either"
Tim Bird questions whether the boot time cost of the random feeding may
be noticeable. And "add_device_randomness()" is definitely not some
speed deamon of a function.
* tag 'devicetree-for-linus' of git://git.secretlab.ca/git/linux:
of/platform: add error reporting to of_amba_device_create()
irq/of: Fix comment typo for irq_of_parse_and_map
of: Feed entire flattened device tree into the random pool
of/fdt: Clean up casting in unflattening path
of/fdt: Remove duplicate memory clearing on FDT unflattening
gpio: implement gpio-ranges binding document fix
of: call __of_parse_phandle_with_args from of_parse_phandle
of: introduce of_parse_phandle_with_fixed_args
of: move of_parse_phandle()
of: move documentation of of_parse_phandle_with_args
of: Fix missing memory initialization on FDT unflattening
of: consolidate definition of early_init_dt_alloc_memory_arch()
of: Make of_get_phy_mode() return int i.s.o. const int
include: dt-binding: input: create a DT header defining key codes.
of/platform: Staticize of_platform_device_create_pdata()
of: Specify initrd location using 64-bit
dt: Typo fix
OF: make of_property_for_each_{u32|string}() use parameters if OF is not enabled
Pull slave-dmaengine updates from Vinod Koul:
"This pull brings:
- Andy's DW driver updates
- Guennadi's sh driver updates
- Pl08x driver fixes from Tomasz & Alban
- Improvements to mmp_pdma by Daniel
- TI EDMA fixes by Joel
- New drivers:
- Hisilicon k3dma driver
- Renesas rcar dma driver
- New API for publishing slave driver capablities
- Various fixes across the subsystem by Andy, Jingoo, Sachin etc..."
* 'for-linus' of git://git.infradead.org/users/vkoul/slave-dma: (94 commits)
dma: edma: Remove limits on number of slots
dma: edma: Leave linked to Null slot instead of DUMMY slot
dma: edma: Find missed events and issue them
ARM: edma: Add function to manually trigger an EDMA channel
dma: edma: Write out and handle MAX_NR_SG at a given time
dma: edma: Setup parameters to DMA MAX_NR_SG at a time
dmaengine: pl330: use dma_set_max_seg_size to set the sg limit
dmaengine: dma_slave_caps: remove sg entries
dma: replace devm_request_and_ioremap by devm_ioremap_resource
dma: ste_dma40: Fix potential null pointer dereference
dma: ste_dma40: Remove duplicate const
dma: imx-dma: Remove redundant NULL check
dma: dmagengine: fix function names in comments
dma: add driver for R-Car HPB-DMAC
dma: k3dma: use devm_ioremap_resource() instead of devm_request_and_ioremap()
dma: imx-sdma: Staticize sdma_driver_data structures
pch_dma: Add MODULE_DEVICE_TABLE
dmaengine: PL08x: Add cyclic transfer support
dmaengine: PL08x: Fix reading the byte count in cctl
dmaengine: PL08x: Add support for different maximum transfer size
...
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=+EYB
-----END PGP SIGNATURE-----
Merge tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.12:
Core:
- Support Allocation Units 8MB-64MB in SD3.0, previous max was 4MB.
- The slot-gpio helper can now handle GPIO debouncing card-detect.
- Read supported voltages from DT "voltage-ranges" property.
Drivers:
- dw_mmc: Add support for ARC architecture, and support exynos5420.
- mmc_spi: Support CD/RO GPIOs.
- sh_mobile_sdhi: Add compatibility for more Renesas SoCs.
- sh_mmcif: Add DT support for DMA channels"
* tag 'mmc-updates-for-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (50 commits)
Revert "mmc: tmio-mmc: Remove .set_pwr() callback from platform data"
mmc: dw_mmc: Add support for ARC
mmc: sdhci-s3c: initialize host->quirks2 for using quirks2
mmc: sdhci-s3c: fix the wrong register value, when clock is disabled
mmc: esdhc: add support to get voltage from device-tree
mmc: sdhci: get voltage from sdhc host
mmc: core: parse voltage from device-tree
mmc: omap_hsmmc: use the generic config for omap2plus devices
mmc: omap_hsmmc: clear status flags before starting a new command
mmc: dw_mmc: exynos: Add a new compatible string for exynos5420
mmc: sh_mmcif: revision-specific CLK_CTRL2 handling
mmc: sh_mmcif: revision-specific Command Completion Signal handling
mmc: sh_mmcif: add support for Device Tree DMA bindings
mmc: sh_mmcif: move header include from header into .c
mmc: SDHI: add DT compatibility strings for further SoCs
mmc: dw_mmc-pci: enable bus-mastering mode
mmc: dw_mmc-pci: get resources from a proper BAR
mmc: tmio-mmc: Remove .set_pwr() callback from platform data
mmc: tmio-mmc: Remove .get_cd() callback from platform data
mmc: sh_mobile_sdhi: Remove .set_pwr() callback from platform data
...
These legacy drivers were removed in commit
9c75fc8c5c ("CRIS: Remove legacy RTC
drivers"). Now remove their last traces in two Kconfig files and one
Makefile.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jesper Nilsson <jespern@axis.com>
The Kconfig symbol OOM_REBOOT got added in v2.6.25. It has never been
used. Its entry can safely be removed.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
b3af11afe0 ("x86: get rid of pt_regs argument of iopl(2)")
dropped PTREGSCALL which was also the last user of save_rest.
Drop that now-unused function too.
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Link: http://lkml.kernel.org/r/1378546750-19727-1-git-send-email-bp@suse.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This fixes the following build error:
/tmp/cce439dZ.s: Assembler messages:
/tmp/cce439dZ.s:506: Error: selected processor does not support ARM mode `isb '
/tmp/cce439dZ.s:512: Error: selected processor does not support ARM mode `isb '
/tmp/cce439dZ.s:513: Error: selected processor does not support ARM mode `dsb '
/tmp/cce439dZ.s:583: Error: selected processor does not support ARM mode `isb '
/tmp/cce439dZ.s:589: Error: selected processor does not support ARM mode `isb '
/tmp/cce439dZ.s:590: Error: selected processor does not support ARM mode `dsb '
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Nicolas Pitre <nico@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
From Peter Maydell:
These patches fix a number of issues with the PCI controller
code for mach-versatile:
(1) The irq mapping matched neither hardware nor QEMU; we correct
it to match the hardware, which means it will also work on recent
(1.5 or later) QEMU.
(2) The code was confused between the PCI I/O window (at 0x43000000)
and the first PCI memory window (at 0x44000000), which meant that
PCI devices using PCI PIO rather than MMIO didn't work. This is
fixed (and some variables/labels are renamed to avoid further
confusion in future).
(3) The SMAP register offsets were all off-by-four, though by
fluke this didn't actually have any ill effects.
All these changes have been tested on real hardware (PB926
plus the PCI backplane), as well as on QEMU. I have confirmed
that IRQs and PCI PIO and MMIO work OK.
PCI bus-master DMA doesn't seem to work on h/w -- as far as I can
tell the device is correctly managing to DMA to the right places
in memory, but every other 32 bit word is corrupt (at least judging
from rtl8139 debug dumps of the frames it's receiving). I'm not
sure what's going on here, but since this is disjoint from
the irq and I/O issues I don't think that applying the
patches that fix those should be stalled on trying to debug
DMA problems. (DMA works fine on QEMU, incidentally.)
* versatile/fixes:
ARM: PCI: versatile: Fix SMAP register offsets
ARM: PCI: versatile: Fix PCI I/O
ARM: PCI: versatile: Fix map_irq function to match hardware
Signed-off-by: Olof Johansson <olof@lixom.net>
As of 8d3214c ("sh_eth: remove 'register_type' field from 'struct
sh_eth_plat_data'") is is no longer necessary or correct to use the
'register_type' field from 'struct sh_eth_plat_data' and doing so results
in a build error.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Olof Johansson <olof@lixom.net>
* Update early timer initialisation order of r8a7779 SoC
This resolves a regression introduced by
a894fcc2d0 ("ARM: smp_twd: Divorce smp_twd
from local timer API").
This problem was introduced in v3.10-rc2.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=R9vg
-----END PGP SIGNATURE-----
Merge tag 'renesas-fixes3-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into fixes
From Simon Horman:
Third Round of Renesas ARM based SoC fixes for v3.12
* Update early timer initialisation order of r8a7779 SoC
This resolves a regression introduced by
a894fcc2d0 ("ARM: smp_twd: Divorce smp_twd
from local timer API").
This problem was introduced in v3.10-rc2.
* tag 'renesas-fixes3-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas:
ARM: shmobile: r8a7779: Update early timer initialisation order
Signed-off-by: Olof Johansson <olof@lixom.net>
Commit a6e56c28a1 (ARM: pxa: ssp: add DT bindings) causes warnings
when built:
arch/arm/plat-pxa/ssp.c: In function 'pxa_ssp_probe':
arch/arm/plat-pxa/ssp.c:145:17: warning: 'dma_spec.args[0]' may be used
uninitialized in this function [-Wmaybe-uninitialized]
Resolve by checking return values and aborting when lookups fail.
Cc: Daniel Mack <zonque@gmail.com>
Cc: Mark Brown <broonie@linaro.org>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
These are changes that arrived a little late before the merge window,
or had dependencies on previous branches.
Highlights:
- ux500: misc. cleanup, fixup I2C devices
- exynos: DT updates for RTC; PM updates
- at91: DT updates for NAND; new platforms added to generic defconfig
- sunxi: DT updates: cubieboard2, pinctrl driver, gated clocks
- highbank: LPAE fixes, select necessary ARM errata
- omap: PM fixes and improvements; OMAP5 mailbox support
- omap: basic support for new DRA7xx SoCs
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=NIZZ
-----END PGP SIGNATURE-----
Merge tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC late changes from Kevin Hilman:
"These are changes that arrived a little late before the merge window,
or had dependencies on previous branches.
Highlights:
- ux500: misc. cleanup, fixup I2C devices
- exynos: DT updates for RTC; PM updates
- at91: DT updates for NAND; new platforms added to generic defconfig
- sunxi: DT updates: cubieboard2, pinctrl driver, gated clocks
- highbank: LPAE fixes, select necessary ARM errata
- omap: PM fixes and improvements; OMAP5 mailbox support
- omap: basic support for new DRA7xx SoCs"
* tag 'late-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (60 commits)
ARM: dts: vexpress: Add CCI node to TC2 device-tree
ARM: EXYNOS: Skip C1 cpuidle state for exynos5440
ARM: EXYNOS: always enable PM domains support for EXYNOS4X12
ARM: highbank: clean-up some unused includes
ARM: sun7i: Enable the A20 clocks in the DTSI
ARM: sun6i: Enable clock support in the DTSI
ARM: sun5i: dt: Use the A10s gates in the DTSI
ARM: at91: at91_dt_defconfig: enable rm9200 support
ARM: dts: add ADC device tree node for exynos5420/5250
ARM: dts: Add RTC DT node to Exynos5420 SoC
ARM: dts: Update the "status" property of RTC DT node for Exynos5250 SoC
ARM: dts: Fix the RTC DT node name for Exynos5250
irqchip: mmp: avoid to include irqs head file
ARM: mmp: avoid to include head file in mach-mmp
irqchip: mmp: support irqchip
irqchip: move mmp irq driver
ARM: OMAP: AM33xx: clock: Add RNG clock data
ARM: OMAP: TI81XX: add always-on powerdomain for TI81XX
ARM: OMAP4: clock: Lock PLLs in the right sequence
ARM: OMAP: AM33XX: hwmod: Add hwmod data for debugSS
...
Lots of cleanup and refactoring and some SMP additions for Renesas
platforms. Due to some inter-dependencies with other arm-soc
branches, this Renesas stuff was separated out for sending after the
other branches were merged.
Highlights:
- remove unused board support and cleanup of unused headers
- refactoring of init and device registration
- simplify IRQ initialization
Conflicts: Too many. Most of these are because Simon chose to send
some board updates through the V4L tree that ends up colliding with
the main platform changes. We'll work with him on sorting out his
workflow:
- arch/arm/boot/dts/r8a7740.dtsi:
- Add/add conflict in a devicetree file (keep both)
- arch/arm/mach-shmobile/Makefile:
- Splitting out of clock files collides with intc move to DT.
Keep HEAD version but remove intc-* files for R8A7740 and R8A7779.
- arch/arm/mach-shmobile/board-bockw.c:
- Keep HEAD but remove i2c, hspi and mmc device init calls
- arch/arm/mach-shmobile/board-marzen.c
- Remove mach/hardware.h include and r8a7779_add_usb_phy_device() call,
everything else stays.
- arch/arm/mach-shmobile/include/mach/r8a7778.h:
- From HEAD, Keep camera-rcar.h include and r8a7778_add_vin_device()
- From branch, keep everything
- arch/arm/mach-shmobile/include/mach/r8a7779.h:
- From HEAD, Keep only camera-rcar.h include and r8a7779_add_vin_device()
- arch/arm/mach-shmobile/setup-r8a7778.c
- Keep HEAD, but drop the MMC section (struct resource + add_mmc_device())
- take the new function name from our side (r8a7778_add_dt_devices())
- arch/arm/mach-shmobile/setup-r8a7779.c
- Keep HEAD, but drop r8a7779_add_usb_phy_device()
I've also pushed a test-merge2 branch where you can see how I resolved
them.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=Fagt
-----END PGP SIGNATURE-----
Merge tag 'renesas-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM Renesas SoC cleanup, refactoring and more SMP support from Kevin Hilman:
"Lots of cleanup and refactoring and some SMP additions for Renesas
platforms. Due to some inter-dependencies with other arm-soc
branches, this Renesas stuff was separated out for sending after the
other branches were merged.
Highlights:
- remove unused board support and cleanup of unused headers
- refactoring of init and device registration
- simplify IRQ initialization"
* tag 'renesas-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (68 commits)
ARM: shmobile: Per-CPU SMP boot / sleep code for SCU SoCs
ARM: shmobile: Introduce per-CPU SMP boot / sleep code
ARM: shmobile: Use shared SCU CPU Hotplug code on r8a7779
ARM: shmobile: Use shared SCU CPU Hotplug code on sh73a0
ARM: shmobile: Add shared SCU CPU Hotplug code
ARM: shmobile: Use shared SCU SMP boot code on emev2
ARM: shmobile: Use shared SCU SMP boot code on r8a7779
ARM: shmobile: Use shared SCU SMP boot code on sh73a0
ARM: shmobile: Introduce shared SCU SMP boot code
ARM: shmobile: sh73a0: Remove global GPIO_NR definition
ARM: shmobile: kzm9d: remove nfsroot settings from bootargs
ARM: shmobile: armadillo800eva: remove nfsroot settings from bootargs
ARM: shmobile: r8a7779: move r8a7779_init_irq_xxx() to setup
ARM: shmobile: r8a7740: move r8a7740_init_irq_of() to setup
ARM: shmobile: bockw: add missing __initdata
ARM: shmobile: r8a7790: add missing __initdata
ARM: shmobile: r8a7779: add missing __initdata
ARM: shmobile: Remove unused shmobile_init_time()
ARM: shmobile: Use clocksource_of_init() on r8a7790
ARM: shmobile: Use default ->init_time() on KZM9G DT ref
...
This branch contains ARM SoC related driver updates for v3.12. The
only thing this cycle are core PM updates and CPUidle support for
ARM's TC2 big.LITTLE development platform.
Conflicts:
One cleanup/reorg conflict with a new entry in
drivers/cpuidle/Makefile. Append the new entry after the existing
ones. A follow up patch for v3.12-rc will make the new entry conform
to the cleanup/reorg.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=FvQD
-----END PGP SIGNATURE-----
Merge tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver update from Kevin Hilman:
"This contains the ARM SoC related driver updates for v3.12. The only
thing this cycle are core PM updates and CPUidle support for ARM's TC2
big.LITTLE development platform"
* tag 'drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
cpuidle: big.LITTLE: vexpress-TC2 CPU idle driver
ARM: vexpress: tc2: disable GIC CPU IF in tc2_pm_suspend
drivers: irq-chip: irq-gic: introduce gic_cpu_if_down()
patches, both new drivers and fixes to existing. A high percentage of
these are for Samsung platforms like Exynos. Core framework fixes and
some new features like automagical clock re-parenting round out the
patches.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=5GfA
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux
Pull clock framework changes from Michael Turquette:
"The common clk framework changes for 3.12 are dominated by clock
driver patches, both new drivers and fixes to existing. A high
percentage of these are for Samsung platforms like Exynos. Core
framework fixes and some new features like automagical clock
re-parenting round out the patches"
* tag 'clk-for-linus-3.12' of git://git.linaro.org/people/mturquette/linux: (102 commits)
clk: only call get_parent if there is one
clk: samsung: exynos5250: Simplify registration of PLL rate tables
clk: samsung: exynos4: Register PLL rate tables for Exynos4x12
clk: samsung: exynos4: Register PLL rate tables for Exynos4210
clk: samsung: exynos4: Reorder registration of mout_vpllsrc
clk: samsung: pll: Add support for rate configuration of PLL46xx
clk: samsung: pll: Use new registration method for PLL46xx
clk: samsung: pll: Add support for rate configuration of PLL45xx
clk: samsung: pll: Use new registration method for PLL45xx
clk: samsung: exynos4: Rename exynos4_plls to exynos4x12_plls
clk: samsung: exynos4: Remove checks for DT node
clk: samsung: exynos4: Remove unused static clkdev aliases
clk: samsung: Modify _get_rate() helper to use __clk_lookup()
clk: samsung: exynos4: Use separate aliases for cpufreq related clocks
clocksource: samsung_pwm_timer: Get clock from device tree
ARM: dts: exynos4: Specify PWM clocks in PWM node
pwm: samsung: Update DT bindings documentation to cover clocks
clk: Move symbol export to proper location
clk: fix new_parent dereference before null check
clk: wm831x: Initialise wm831x pointer on init
...
are still in flux, and will have to wait for 3.13.
The changes for 3.12 are mostly clean ups and minor fixes.
H. Peter Anvin added a check to x86_32 static function tracing that
helps a small segment of the kernel community.
Oleg Nesterov had a few changes from 3.11, but were mostly clean ups
and not worth pushing in the -rc time frame.
Li Zefan had small clean up with annotating a raw_init with __init.
I fixed a slight race in updating function callbacks, but the race
is so small and the bug that happens when it occurs is so minor it's
not even worth pushing to stable.
The only real enhancement is from Alexander Z Lam that made the
tracing_cpumask work for trace buffer instances, instead of them all
sharing a global cpumask.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iQEcBAABAgAGBQJSLJm1AAoJEOdOSU1xswtMSu0H/0/Uuh0D5VhANZRcTATY4gUO
n3WH6sm3atOxH+cbeYQcFXxOcvRcR2n90tvCMpiFlPiC0NiNR1yjro3VLS4zWb77
twq7gABdJf+Tdq7sOBmSzmY5vRKQVHIXvAfC27mBez38nCWZz0BjJGEsPBwoly25
ZaiCbKlusw/QKIEy40tuKUL/rXF6yEWnQrMujhBbyNm0w7sJVdfnd+HHmCvy15H2
IQE1g83d/dAMBjFY2BYg77J+oV6qmJxql2itvDivQWXHqFb52Jw3ZTwHwWLZlPYU
AZcHtYGs2lSUscQLF56LejB7zZyE8taUufExFEVexXxZS5u7nNPXsPrA2LOOK70=
=JWO6
-----END PGP SIGNATURE-----
Merge tag 'trace-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace
Pull tracing updates from Steven Rostedt:
"Not much changes for the 3.12 merge window. The major tracing changes
are still in flux, and will have to wait for 3.13.
The changes for 3.12 are mostly clean ups and minor fixes.
H Peter Anvin added a check to x86_32 static function tracing that
helps a small segment of the kernel community.
Oleg Nesterov had a few changes from 3.11, but were mostly clean ups
and not worth pushing in the -rc time frame.
Li Zefan had small clean up with annotating a raw_init with __init.
I fixed a slight race in updating function callbacks, but the race is
so small and the bug that happens when it occurs is so minor it's not
even worth pushing to stable.
The only real enhancement is from Alexander Z Lam that made the
tracing_cpumask work for trace buffer instances, instead of them all
sharing a global cpumask"
* tag 'trace-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
ftrace/rcu: Do not trace debug_lockdep_rcu_enabled()
x86-32, ftrace: Fix static ftrace when early microcode is enabled
ftrace: Fix a slight race in modifying what function callback gets traced
tracing: Make tracing_cpumask available for all instances
tracing: Kill the !CONFIG_MODULES code in trace_events.c
tracing: Don't pass file_operations array to event_create_dir()
tracing: Kill trace_create_file_ops() and friends
tracing/syscalls: Annotate raw_init function with __init
For 3.12-rc1 there are a number of bugfixes in addition to work to ease usage
of shared code between libxfs and the kernel, the rest of the work to enable
project and group quotas to be used simultaneously, performance optimisations
in the log and the CIL, directory entry file type support, fixes for log space
reservations, some spelling/grammar cleanups, and the addition of user
namespace support.
- introduce readahead to log recovery
- add directory entry file type support
- fix a number of spelling errors in comments
- introduce new Q_XGETQSTATV quotactl for project quotas
- add USER_NS support
- log space reservation rework
- CIL optimisations
- kernel/userspace libxfs rework
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=V4s4
-----END PGP SIGNATURE-----
Merge tag 'xfs-for-linus-v3.12-rc1' of git://oss.sgi.com/xfs/xfs
Pull xfs updates from Ben Myers:
"For 3.12-rc1 there are a number of bugfixes in addition to work to
ease usage of shared code between libxfs and the kernel, the rest of
the work to enable project and group quotas to be used simultaneously,
performance optimisations in the log and the CIL, directory entry file
type support, fixes for log space reservations, some spelling/grammar
cleanups, and the addition of user namespace support.
- introduce readahead to log recovery
- add directory entry file type support
- fix a number of spelling errors in comments
- introduce new Q_XGETQSTATV quotactl for project quotas
- add USER_NS support
- log space reservation rework
- CIL optimisations
- kernel/userspace libxfs rework"
* tag 'xfs-for-linus-v3.12-rc1' of git://oss.sgi.com/xfs/xfs: (112 commits)
xfs: XFS_MOUNT_QUOTA_ALL needed by userspace
xfs: dtype changed xfs_dir2_sfe_put_ino to xfs_dir3_sfe_put_ino
Fix wrong flag ASSERT in xfs_attr_shortform_getvalue
xfs: finish removing IOP_* macros.
xfs: inode log reservations are too small
xfs: check correct status variable for xfs_inobt_get_rec() call
xfs: inode buffers may not be valid during recovery readahead
xfs: check LSN ordering for v5 superblocks during recovery
xfs: btree block LSN escaping to disk uninitialised
XFS: Assertion failed: first <= last && last < BBTOB(bp->b_length), file: fs/xfs/xfs_trans_buf.c, line: 568
xfs: fix bad dquot buffer size in log recovery readahead
xfs: don't account buffer cancellation during log recovery readahead
xfs: check for underflow in xfs_iformat_fork()
xfs: xfs_dir3_sfe_put_ino can be static
xfs: introduce object readahead to log recovery
xfs: Simplify xfs_ail_min() with list_first_entry_or_null()
xfs: Register hotcpu notifier after initialization
xfs: add xfs sb v4 support for dirent filetype field
xfs: Add write support for dirent filetype field
xfs: Add read-only support for dirent filetype field
...
- nand-gpio cleanup and portability to non-ARM
- m25p80 support for 4-byte addressing chips, other new chips
- pxa3xx cleanup and support for new platforms
- remove obsolete alauda, octagon-5066 drivers
- erase/write support for bcm47xxsflash
- improve detection of ECC requirements for NAND, controller setup
- NFC acceleration support for atmel-nand, read/write via SRAM
- etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)
iEYEABECAAYFAlIt3VsACgkQdwG7hYl686NKBQCgqFzV1S+TiXZSjbqanK0374Hu
lMIAoI2IOQb1bgQFSqaOzgSaBmVhLtMc
=xWBt
-----END PGP SIGNATURE-----
Merge tag 'for-linus-20130909' of git://git.infradead.org/linux-mtd
Pull mtd updates from David Woodhouse:
- factor out common code from MTD tests
- nand-gpio cleanup and portability to non-ARM
- m25p80 support for 4-byte addressing chips, other new chips
- pxa3xx cleanup and support for new platforms
- remove obsolete alauda, octagon-5066 drivers
- erase/write support for bcm47xxsflash
- improve detection of ECC requirements for NAND, controller setup
- NFC acceleration support for atmel-nand, read/write via SRAM
- etc
* tag 'for-linus-20130909' of git://git.infradead.org/linux-mtd: (184 commits)
mtd: chips: Add support for PMC SPI Flash chips in m25p80.c
mtd: ofpart: use for_each_child_of_node() macro
mtd: mtdswap: replace strict_strtoul() with kstrtoul()
mtd cs553x_nand: use kzalloc() instead of memset
mtd: atmel_nand: fix error return code in atmel_nand_probe()
mtd: bcm47xxsflash: writing support
mtd: bcm47xxsflash: implement erasing support
mtd: bcm47xxsflash: convert to module_platform_driver instead of init/exit
mtd: bcm47xxsflash: convert kzalloc to avoid invalid access
mtd: remove alauda driver
mtd: nand: mxc_nand: mark 'const' properly
mtd: maps: cfi_flagadm: add missing __iomem annotation
mtd: spear_smi: add missing __iomem annotation
mtd: r852: Staticize local symbols
mtd: nandsim: Staticize local symbols
mtd: impa7: add missing __iomem annotation
mtd: sm_ftl: Staticize local symbols
mtd: m25p80: add support for mr25h10
mtd: m25p80: make CONFIG_M25PXX_USE_FAST_READ safe to enable
mtd: m25p80: Pass flags through CAT25_INFO macro
...
Pull DMA mapping update from Marek Szyprowski:
"This contains an addition of Device Tree support for reserved memory
regions (Contiguous Memory Allocator is one of the drivers for it) and
changes required by the KVM extensions for PowerPC architectue"
* 'for-v3.12' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
ARM: init: add support for reserved memory defined by device tree
drivers: of: add initialization code for dma reserved memory
drivers: of: add function to scan fdt nodes given by path
drivers: dma-contiguous: clean source code and prepare for device tree
CC:stable. But for that reason, I did a merge with master partway
through to avoid an unnecessary conflict.
Also: a fun lguest bug turns out if you don't clear the TF flag when trapping
Bad Things happen to the guest kernel as the stack overflows...
Cheers,
Rusty.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)
iQIcBAABAgAGBQJSLVvbAAoJENkgDmzRrbjxLp0P/ivSWpHo6qPvOGG/xBCSCUX0
lHb8murQOy48g8i5vcZAkkLZIxoxonMwpst91zLawH6c0iifwIqPSvwqzQhcjuxj
5766Ntbdz5n5H1AEKrFnANAGMJ25f0b5irixzCSAADlDOYelaoGWfjsxTf7ZgU4i
qYd0x3RuIUDU5dk5LRHJTpml5yai372xvV3AOyYc6l0lxCgfRt87hYrQmBpgxrfC
KtHIYS3pw3582bMlKn77WHRjC4Ca6w0X36HfeyyToOh27B89TFw2D53Fb9EDzEN/
do8RxGGmXHSkg6gh1TYUGvNs21Lv0jmzn/Zejzyn7i0UscnjFAksoARi6Eh00xri
ZkkBoq8HZVEDu/uh3/J5HRgC6/HNyKd9C4uZ8zflMqV8VHgtdyciDH4uqoFXCesv
vRrfBNadmvTjFOhQ1bCi/GUOWdaCNoVfE+3WZ+0FvFhS2o5RPusVuSGLXQDm7frV
UejvK8gZ8LnQ1SS3KZ/7UZPeym9WXh7/62VI3bIQb97a/sBRQZYR/JOg+lOQcLhu
bVfP2KO2zk+L8NKYJ3Jg+JJXswzIgtGx4WLqvfqY4TOR8Gt/VMT5zCmGXoMI+te5
JcHLLC713kVSa4jgbdoErk+WxvN5LsDfIPKWxl4t/AfIVSS2ZxvwTQKAbMZkyDwx
qcLpnfANeqS8bzXgRtxG
=MFZ1
-----END PGP SIGNATURE-----
Merge tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux
Pull virtio update from Rusty Russell:
"More console fixes; these are the theoretical ones which didn't get
CC:stable. But for that reason, I did a merge with master partway
through to avoid an unnecessary conflict.
Also: a fun lguest bug turns out if you don't clear the TF flag when
trapping Bad Things happen to the guest kernel as the stack
overflows..."
* tag 'virtio-next-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux:
virtio_pci: pm: Use CONFIG_PM_SLEEP instead of CONFIG_PM
lguest: fix GPF in guest when using gdb.
lguest: fix guest kernel stack overflow when TF bit set.
lguest: fix BUG_ON() in invalid guest page table.
virtio: console: prevent use-after-free of port name in port unplug
virtio: console: cleanup an error message
virtio: console: fix locking around send_sigio_to_port()
virtio: console: add locking in port unplug path
virtio: console: add locks around buffer removal in port unplug path
tools/lguest: offer VIRTIO_F_ANY_LAYOUT for net device.
virtio tools: add .gitignore
lguest: Point to the right directory for the lguest launcher
As we get compile warnings about .init.data being
used by non-init functions.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
- Device tree updates for TZ1090 GPIO drivers merged via GPIO tree.
- Add driver for ImgTec PDC irqchip as found in TZ1090 SoC.
- Add linux-metag mailing list to MAINTAINERS file.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.13 (GNU/Linux)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=WHe5
-----END PGP SIGNATURE-----
Merge tag 'metag-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag
Pull metag architecture changes from James Hogan:
- Device tree updates for TZ1090 GPIO drivers merged via GPIO tree.
- Add driver for ImgTec PDC irqchip as found in TZ1090 SoC.
- Add linux-metag mailing list to MAINTAINERS file.
* tag 'metag-for-v3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/jhogan/metag:
irq-imgpdc: add ImgTec PDC irqchip driver
MAINTAINERS: add linux-metag mailing list
metag: tz1090: instantiate gpio-tz1090-pdc
metag: tz1090: select and instantiate gpio-tz1090
metag: tz1090: select and instantiate irq-imgpdc
This reverts commit 70dd4998cb.
Now that the bugs have been resolved we can re-enable the
PV ticketlock implementation under PVHVM Xen guests.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
There is no need to setup this kicker IPI if we are never going
to use the paravirtualized ticketlock mechanism.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
Before this patch we would patch all of the pv_lock_ops sites
using alternative assembler. Then later in the bootup cycle
change the unlock_kick and lock_spinning to the Xen specific -
without re patching.
That meant that for the core of the kernel we would be running
with the baremetal version of unlock_kick and lock_spinning while
for modules we would have the proper Xen specific slowpaths.
As most of the module uses some API from the core kernel that ended
up with slowpath lockers waiting forever to be kicked (b/c they
would be using the Xen specific slowpath logic). And the
kick never came b/c the unlock path that was taken was the
baremetal one.
On PV we do not have the problem as we initialise before the
alternative code kicks in.
The fix is to make the updating of the pv_lock_ops function
be done before the alternative code starts patching.
Note that this patch fixes issues discovered by commit
f10cd522c5.
("xen: disable PV spinlocks on HVM") wherein it mentioned
PV spinlocks cannot possibly work with the current code because they are
enabled after pvops patching has already been done, and because PV
spinlocks use a different data structure than native spinlocks so we
cannot switch between them dynamically.
The first problem is solved by this patch.
The second problem has been solved by commit
816434ec4a
(Merge branch 'x86-spinlocks-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip)
P.S.
There is still the commit 70dd4998cb
(xen/spinlock: Disable IRQ spinlock (PV) allocation on PVHVM) to
revert but that can be done later after all other bugs have been
fixed.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
As we are using the generic ticketlock structs and these
old structures are not needed anymore.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
The xen_lock_spinning has a check for the kicker interrupts
and if it is not initialized it will spin normally (not enter
the slowpath).
But for PVHVM case we would initialize the kicker interrupt
before the CPU came online. This meant that if the booting
CPU used a spinlock and went in the slowpath - it would
enter the slowpath and block forever. The forever part because
during bootup: the spinlock would be taken _before_ the CPU
sets itself to be online (more on this further), and we enter
to poll on the event channel forever.
The bootup CPU (see commit fc78d343fa
"xen/smp: initialize IPI vectors before marking CPU online"
for details) and the CPU that started the bootup consult
the cpu_online_mask to determine whether the booting CPU should
get an IPI. The booting CPU has to set itself in this mask via:
set_cpu_online(smp_processor_id(), true);
However, if the spinlock is taken before this (and it is) and
it polls on an event channel - it will never be woken up as
the kernel will never send an IPI to an offline CPU.
Note that the PVHVM logic in sending IPIs is using the HVM
path which has numerous checks using the cpu_online_mask
and cpu_active_mask. See above mention git commit for details.
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Reviewed-by: David Vrabel <david.vrabel@citrix.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSGqS5AAoJEHm+PkMAQRiGFxEH/3VrqF6WAkcviNiW/0DCdO8k
v6Wi7Sp5LxVkwzmOCHCV1tTHwLRlH3cB9YmJlGQ0kHCREaAuEQAB0xJXIW7dnyYj
Qq7KoRZEMe3wizmjEsj8qsrhfMLzHjBw67hBz2znwW/4P7YdgzwD7KRiEat+yRC9
ON3nNL2zIqpfk92RXvVrSVl4KMEM+WNbOfiffgBiEP24Ja1MJMFH1d4i6hNOaB0x
9Pb3Lw8let92x+8Ao5jnjKdKMgVsoZWbN/TgQR8zZOHM38AGGiDgk18vMz+L+hpS
jqfjckxj1m30jGq0qZ9ZbMZx3IGif4KccVr30MqNHJpwi6Q24qXvT3YfA3HkstM=
=nAab
-----END PGP SIGNATURE-----
Merge tag 'v3.11-rc7' into stable/for-linus-3.12
Linux 3.11-rc7
As we need the git commit 28817e9de4f039a1a8c1fe1df2fa2df524626b9e
Author: Chuck Anderson <chuck.anderson@oracle.com>
Date: Tue Aug 6 15:12:19 2013 -0700
xen/smp: initialize IPI vectors before marking CPU online
* tag 'v3.11-rc7': (443 commits)
Linux 3.11-rc7
ARC: [lib] strchr breakage in Big-endian configuration
VFS: collect_mounts() should return an ERR_PTR
bfs: iget_locked() doesn't return an ERR_PTR
efs: iget_locked() doesn't return an ERR_PTR()
proc: kill the extra proc_readfd_common()->dir_emit_dots()
cope with potentially long ->d_dname() output for shmem/hugetlb
usb: phy: fix build breakage
USB: OHCI: add missing PCI PM callbacks to ohci-pci.c
staging: comedi: bug-fix NULL pointer dereference on failed attach
lib/lz4: correct the LZ4 license
memcg: get rid of swapaccount leftovers
nilfs2: fix issue with counting number of bio requests for BIO_EOPNOTSUPP error detection
nilfs2: remove double bio_put() in nilfs_end_bio_write() for BIO_EOPNOTSUPP error
drivers/platform/olpc/olpc-ec.c: initialise earlier
ipv4: expose IPV4_DEVCONF
ipv6: handle Redirect ICMP Message with no Redirected Header option
be2net: fix disabling TX in be_close()
Revert "ACPI / video: Always call acpi_video_init_brightness() on init"
Revert "genetlink: fix family dump race"
...
Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Pull m68knommu fixes from Greg Ungerer:
"Just a small collection of cleanups and fixes this time, no big
changes. The most interresting are to make the m68k and m68knommu
consistently use CONFIG_IOMAP, clean out some unused board config
options and flush the cache on signal stack creation"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
m68k: remove 16 unused boards in Kconfig.machine
m68k: define 'VM_DATA_DEFAULT_FLAGS' no matter whether has 'NOMMU' or not
m68knommu: user generic iomap to support ioread*/iowrite*
m68k/coldfire: flush cache when creating the signal stack frame
m68knommu: Mark functions only called from setup_arch() __init
Pull UML updates from Richard Weinberger:
"This pile contains mostly fixes and improvements for issues identified
by Richard W M Jones while adding UML as backend to libguestfs"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/uml:
um: Add irq chip um/mask handlers
um: prctl: Do not include linux/ptrace.h
um: Run UML in it's own session.
um: Cleanup SIGTERM handling
um: ubd: Introduce submit_request()
um: ubd: Add REQ_FLUSH suppport
um: Implement probe_kernel_read()
um: hostfs: Fix writeback
* 'x86/spinlocks' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/kvm/guest: Fix sparse warning: "symbol 'klock_waiting' was not declared as static"
kvm: Paravirtual ticketlocks support for linux guests running on KVM hypervisor
kvm guest: Add configuration support to enable debug information for KVM Guests
kvm uapi: Add KICK_CPU and PV_UNHALT definition to uapi
xen, pvticketlock: Allow interrupts to be enabled while blocking
x86, ticketlock: Add slowpath logic
jump_label: Split jumplabel ratelimit
x86, pvticketlock: When paravirtualizing ticket locks, increment by 2
x86, pvticketlock: Use callee-save for lock_spinning
xen, pvticketlocks: Add xen_nopvspin parameter to disable xen pv ticketlocks
xen, pvticketlock: Xen implementation for PV ticket locks
xen: Defer spinlock setup until boot CPU setup
x86, ticketlock: Collapse a layer of functions
x86, ticketlock: Don't inline _spin_unlock when using paravirt spinlocks
x86, spinlock: Replace pv spinlocks with pv ticketlocks
Commit 0195659 introduced a NEON accelerated version of the xor_blocks()
function, but it needs the changes in this patch to allow it to be built
as a module rather than statically into the kernel.
This patch creates a separate module xor-neon.ko which exports the NEON
inner xor_blocks() functions depended upon by the regular xor.ko if it
is built with CONFIG_KERNEL_MODE_NEON=y
Reported-by: Josh Boyer <jwboyer@fedoraproject.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When linux is running as dom0, Xen doesn't show the physical cpu but a
virtual CPU.
On some ARM SOC (for instance the exynos 5250), linux registers callbacks
for cpuidle and cpufreq. When these callbacks are called, they will modify
directly the physical cpu not the virtual one. It can impact the whole board
instead of only dom0.
Signed-off-by: Julien Grall <julien.grall@linaro.org>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
m2p_remove_override() calls get_balloon_scratch_page() in
MULTI_update_va_mapping() even though it already has pointer to this page from
the earlier call (in scratch_page). This second call doesn't have a matching
put_balloon_scratch_page() thus not restoring preempt count back. (Also, there
is no put_balloon_scratch_page() in the error path.)
In addition, the second multicall uses __xen_mc_entry() which does not disable
interrupts. Rearrange xen_mc_* calls to keep interrupts off while performing
multicalls.
This commit fixes a regression introduced by:
commit ee0726407f
Author: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Date: Tue Jul 23 17:23:54 2013 +0000
xen/m2p: use GNTTABOP_unmap_and_replace to reinstate the original mapping
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Reviewed-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
xen_pm_init was unconditionally setting pm_power_off and arm_pm_restart
function pointers. This breaks multi-platform kernels. Make this
conditional on running as a Xen guest and make it a late_initcall to
ensure it is setup after platform code for Dom0.
Signed-off-by: Rob Herring <rob.herring@calxeda.com>
Signed-off-by: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
CC: stable@vger.kernel.org
Change the hash algorithm a bit so it produces only values in the
range of 0..31.
This allows to reduce the size of the external interrupt handler hash
array even further while making sure that each of the known interrupt
sources keeps its unique hash with the slightly modified algorithm:
0x1004 --> 12
0x1201 --> 10
0x1202 --> 11
0x1406 --> 16
0x1407 --> 17
0x2401 --> 19
0x2603 --> 22
0x4000 --> 0
This also means that the entire array now fits into exactly one cache
line; so add a proper align statement as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Pull crypto update from Herbert Xu:
"Here is the crypto update for 3.12:
- Added MODULE_SOFTDEP to allow pre-loading of modules.
- Reinstated crct10dif driver using the module softdep feature.
- Allow via rng driver to be auto-loaded.
- Split large input data when necessary in nx.
- Handle zero length messages correctly for GCM/XCBC in nx.
- Handle SHA-2 chunks bigger than block size properly in nx.
- Handle unaligned lengths in omap-aes.
- Added SHA384/SHA512 to omap-sham.
- Added OMAP5/AM43XX SHAM support.
- Added OMAP4 TRNG support.
- Misc fixes"
* git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (66 commits)
Reinstate "crypto: crct10dif - Wrap crc_t10dif function all to use crypto transform framework"
hwrng: via - Add MODULE_DEVICE_TABLE
crypto: fcrypt - Fix bitoperation for compilation with clang
crypto: nx - fix SHA-2 for chunks bigger than block size
crypto: nx - fix GCM for zero length messages
crypto: nx - fix XCBC for zero length messages
crypto: nx - fix limits to sg lists for AES-CCM
crypto: nx - fix limits to sg lists for AES-XCBC
crypto: nx - fix limits to sg lists for AES-GCM
crypto: nx - fix limits to sg lists for AES-CTR
crypto: nx - fix limits to sg lists for AES-CBC
crypto: nx - fix limits to sg lists for AES-ECB
crypto: nx - add offset to nx_build_sg_lists()
padata - Register hotcpu notifier after initialization
padata - share code between CPU_ONLINE and CPU_DOWN_FAILED, same to CPU_DOWN_PREPARE and CPU_UP_CANCELED
hwrng: omap - reorder OMAP TRNG driver code
crypto: omap-sham - correct dma burst size
crypto: omap-sham - Enable Polling mode if DMA fails
crypto: tegra-aes - bitwise vs logical and
crypto: sahara - checking the wrong variable
...
86a264ab "CRED: Wrap current->cred and a few other accessors" converted
all uses of current->cred into current_cred() but left s390 alone.
So let's convert s390 finally as well, only five years later.
This way we also get rid of a sparse warning which complains about a
possible invalid rcu dereference which however is a false positive.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Konrad Rzeszutek Wilk