This makes swap routines operate correctly on the ppc_8xx based machines.
Code has been revalidated on mpc885ads (8M sdram) with recent kernel. Based
on patch from Yuri Tikhonov <yur@emcraft.com> to do the same on arch/ppc
instance.
Recent kernel's size makes swap feature very important on low-memory platforms,
those are actually non-operable without it.
Signed-off-by: Yuri Tikhonov <yur@emcraft.com>
Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Due to chip constraint MPC837x USB DR module can only use
ULPI and serial PHY interfaces. The patch fixes the wrong
type in dts.
Signed-off-by: Li Yang <leoli@freescale.com>
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6:
[Blackfin] arch: current_l1_stack_save is a pointer, so use NULL rather than 0
[Blackfin] arch: fix atomic and32/xor32 comments and ENDPROC markings
[Blackfin] arch: fix bug - allow SDH driver to be used as module
[Blackfin] arch: to kill syscalls missing warning by adding new timerfd syscalls
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] kprobes arch consolidation build fix
[IA64] update efi region debugging to use MB, GB and TB as well as KB
[IA64] use dev_printk in video quirk
[IA64] remove remaining __FUNCTION__ occurrences
[IA64] remove unnecessary nfs includes from sys_ia32.c
[IA64] remove CONFIG_SMP ifdef in ia64_send_ipi()
[IA64] arch_ptrace() cleanup
[IA64] remove duplicate code from arch_ptrace()
[IA64] convert sys_ptrace to arch_ptrace
[IA64] remove find_thread_for_addr()
[IA64] do not sync RBS when changing PT_AR_BSP or PT_CFM
[IA64] access user RBS directly
ia64 named their handler kprobes_fault_handler while all other
arches used kprobe_fault_handler. Change the function definition
and header declaration.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When EFI_DEBUG is defined to a non-zero value in arch/ia64/kernel/efi.c,
the efi memory regions are displayed. This patch enhances the
display code in a few ways:
1. Use TB, GB and MB as well as KB as units.
Although this introduces rounding errors (KB doesn't as
size is always a multiple of 4Kb), it does make
things a lot more readable.
Also as the range is also shown, it is possible to note the exact size
if it is important. In my experience, the size field is mostly useful
for getting a general idea of the size of a region.
On the rx2620 that I use, there actually is an 8TB region (though not
backed by physical memory, and 8TB really is a lot more readable than
8589934592KB.
2. pad the size field with leading spaces to further improve readability
...
... ( 8MB)
... ( 928MB)
... ( 3MB)
...
vs
...
... (8MB)
... (928MB)
... (3MB)
...
3. Pad the attr field out to 64bits using leading zeros,
to further improve readability.
...
mem05: type= 2, attr=0x0000000000000008, range=[0x0000000004000000-0x000000000481f000) ( 8MB)
mem06: type= 7, attr=0x0000000000000008, range=[0x000000000481f000-0x000000003e876000) ( 928MB)
mem07: type= 5, attr=0x8000000000000008, range=[0x000000003e876000-0x000000003eb8e000) ( 3MB)
mem08: type= 4, attr=0x0000000000000008, range=[0x000000003eb8e000-0x000000003ee7a000) ( 2MB)
...
...
mem05: type= 2, attr=0x8, range=[0x0000000004000000-0x000000000481f000) ( 8MB)
mem06: type= 7, attr=0x8, range=[0x000000000481f000-0x000000003e876000) ( 928MB)
mem07: type= 5, attr=0x8000000000000008, range=[0x000000003e876000-0x000000003eb8e000) ( 3MB)
mem08: type= 4, attr=0x8, range=[0x000000003eb8e000-0x000000003ee7a000) ( 2MB)
...
4. Use %d instead of %u for the index field, as i is a signed int.
N.B: This code is not compiled unless EFI_DEBUG is non 0.
Signed-off-by: Simon Horman <horms@verge.net.au>
Signed-off-by: Tony Luck <tony.luck@intel.com>
__FUNCTION__ is gcc-specific, use __func__
Long lines have been kept where they exist, some small spacing changes
have been done.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Compilation of 2.6.25-rc2-mm1 on ia64 generates many warnings.
IA64 support 2 ELF format (IA64 binary and IA32 binary),
thus if 2 elf related header included, cause many warning or error.
about 2 week ago, J. Bruce Fields proposed this problem fixed patch.
(http://marc.info/?l=linux-ia64&m=120329313305695&w=2)
Signed-off-by: J. Bruce Fields <bfields@citi.umich.edu>
Signed-off-by: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
When !CONFIG_SMP, cpu_physical_id() is ia64_get_lid(), which is
functionally identical to
(ia64_getreg(_IA64_REG_CR_LID) >> 16) & 0xffff
so there's no need for two versions of this code.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Correct GPIO pin assignment for the LCD power control (PCI)
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Move the definitions of ATAG_CORE and ATAG_CORE_SIZE in head.S to
head-common.S. There is no use of these in head.S itself, but they
are used in head-common.S. When building for the !CONFIG_MMU case
these were not defined when compiling head-nommu.S (which includes
head-common.S).
Signed-off-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Remove false lockdep warnings about lock recursion when declaring
IRQs as being wake-capable, by marking putting GPIO irq_desc locks
into their own class.
(Thanks to Peter Zijlstra for helping track down such a small
fix to this problem.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <linux@maxim.org.za>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DNS-323, Kurobox-Pro / Linkstation-Pro, QNAP TS-109/TS-209 and some
other orion-based systems have several bogus memory entries in the tag
table, which causes the system to crash at startup. Ignore them by
resetting the tag ID to 0 in a machine fixup function.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This allows monitoring compile issues with Kautobuild for
other omap1 boards until we have more board specific defconfig
files.
After 2.6.25, we can add a generic config_omap_generic16xx to
compile in support for all 16xx boards and then remove other
boards from OSK defconfig.
Signed-off-by: Tony Lindgren <tony@atomide.com>
The only board-specific bits that existed here were for setting up the
IRQs, which are now handled by the SH7710 CPU support code instead. As
there's nothing else to do for setup, kill off the board support code
and have the defconfig use the generic machvec instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There's still work that needs to be done here, and this should not be
enabled by default on existing boards.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This disables the PMB/32BIT=y by default in r7780mp, as turning this on
presently results in build errors (for an admittedly experimental
feature).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the old non-verbose hp6xx apm code and enables some
very basic apm output. We now get percentage (battery) output
and basic time estimate.
Signed-off-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
ERROR: "copy_page" [fs/unionfs/unionfs.ko] undefined!
like all the other architectures.
Cc: Erez Zadok <ezk@cs.sunysb.edu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch fixes the following compile error:
<-- snip -->
...
CC arch/sh/mm/pg-sh7705.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/mm/pg-sh7705.c: In function 'ptep_get_and_clear':
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/sh/mm/pg-sh7705.c:130: error: implicit declaration of function 'mapping_writably_mapped'
make[2]: *** [arch/sh/mm/pg-sh7705.o] Error 1
<-- snip -->
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove all code which does exactly the same thing as ptrace_request().
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
find_thread_for_addr() is no longer needed. It was only used to find
the correct kernel RBS for a given memory address, but since the kernel
RBS is not needed any longer, this function can go away.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Syncing is no longer needed, because user RBS is already
up-to-date. Actually, if a debugger modified the contents
of the original RBS prior to changing PT_AR_BSP, the
modifications would get overwritten.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Because the user RBS of a process is now completely stored in
user-mode when the process is ptrace-stopped, accesses to the
RBS should no longer augment any part of the kernel RBS.
This means we can get rid of most ia64_peek() and ia64_poke()
calls.
Signed-off-by: Petr Tesarik <ptesarik@suse.cz>
Signed-off-by: Tony Luck <tony.luck@intel.com>
We don't need to printk a message every time we transition.
Leave the code there, but ifdef'd out, as it's useful when
adding support for new processors.
Reported-by: Petr Titěra <P.Titera@century.cz>
Signed-off-by: Dave Jones <davej@redhat.com>
/sys/firmware/reipl/nss/name contains the nss name when defsys or
savesys command has been executed. If the defsys or savesys command
fails the kernel_nss_name has to be cleared since a reipl on that
nss name won't be possible.
Signed-off-by: Hongjie Yang <hongjie@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Normally this should not happen, but it's cleaner to do it that way.
Signed-off-by: Michael Holzheu <holzheu@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
IPL from NSS didn't work because the memory detection routine omits any
memory sections with a size lower than what MAX_ORDER defines.
This causes the detection routine to skip the first memory segment which
has a size of 1MB. Which later on will let the kernel think that there
is no memory available at all.
Since in addition the z/VM memory increment size is 1MB force MAX_ORDER
to be 9, so we can support 1MB segments.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Compile smp.o with -Wno-nonnull so gcc stops warning about memcpy
being used with a null parameter. Also remove the workaround code
and use a char * cast instead of a void * cast to do computations.
Cc: Bastian Blank <bastian@waldi.eu.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
If a machine check handling is pending when the idle loop is entered
default_idle will be left with timer ticks and virtual timer disabled.
Fix this by "calling" the idle_chain. Also a BUG_ON(!in_interrupt) in
start_hz_timer must be removed since the function now gets called from
non interrupt context as well.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Fix some spinlock issues reported by lockdep: since the gpio bank
locks can be aquired in both irq and non-irq contexts, they need
to be consistent about always using the irq-safe variants.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Build fix:
arch/arm/mach-omap1/pm.c: In function 'omap_pm_init':
arch/arm/mach-omap1/pm.c:720: warning: passing argument 2 of 'sysfs_create_file' from incompatible pointer type
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
H2 and H3 were broken on by e27a93a944,
which removed declarations for their tps6501x chips. This resolves
that issue for the H2. (Note that this patch *also* broke the isp1301
support on H2; it presumed a not-yet-merged new-style I2c driver.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Get rid of build warnings and errors in mainline for H3 boards; not
all the H3 updates were correct, it seems like the OMAP1 boards are
not getting proper build testing.
Also, commit e27a93a944 introduced a
regression related to the tps65013 chip.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
In mainline, the "old style" I2C registration was only removed for
OMAP2, leading to init-time bugs (regressions) like:
sysfs: duplicate filename 'i2c_omap.1' can not be created
------------[ cut here ]------------
WARNING: at fs/sysfs/dir.c:424 sysfs_add_one+0x40/0xd4()
Modules linked in:
... deletia ...
[<c0036a38>] (omap_init_i2c+0x0/0x50) from [<c000cea8>] (omap_init_devices+0x10/0x24)
r4:c001e000
[<c000ce98>] (omap_init_devices+0x0/0x24) from [<c0008684>] (do_initcalls+0x78/0x200)
... deletia ...
---[ end trace ca143223eefdc828 ]---
kobject_add_internal failed for i2c_omap.1 with -EEXIST, don't try to register things with the same name in the same directory.
The fix is obvious: remove the old init code, it's no longer needed.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove false lockdep warnings about lock recursion when declaring
IRQs as being wake-capable, by marking putting GPIO irq_desc locks
into their own class.
(Thanks to Peter Zijlstra for helping track down such a small
fix to this problem.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This makes parameter passing to DMA handlers uniform between non-chained
and chained transfers and makes debugging easier. Additional data like
chain_id can be always passed to handlers via callback data if needed.
Signed-off-by: Jarkko Nikula <jarkko.nikula@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] fix ia64 kprobes compilation
[IA64] move gcc_intrin.h from header-y to unifdef-y
[IA64] workaround tiger ia64_sal_get_physical_id_info hang
[IA64] move defconfig to arch/ia64/configs/
[IA64] Fix irq migration in multiple vector domain
[IA64] signal(ia64_ia32): add a signal stack overflow check
[IA64] signal(ia64): add a signal stack overflow check
[IA64] CONFIG_SGI_SN2 - auto select NUMA and ACPI_NUMA
Function __copy_user_zeroing in arch/lib/usercopy.c had the wrong parameter
set as __user, and in include/asm-cris/uaccess.h, it was not set at all for
some of the calling functions.
This will cut the number of warnings quite dramatically when using sparse.
While we're here, remove useless CVS log and correct confusing typo.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This just removes unused DEBUG_FORCEDAC define in the IOMMU code.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch makes the IOMMU code not allocate a memory area spanning LLD's
segment boundary.
is_span_boundary() judges whether a memory area spans LLD's segment boundary.
If iommu_arena_find_pages() finds such a area, it tries to find the next
available memory area.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
iommu_arena_find_pages duplicates the code to access to the bitmap for free
space management. This patch convert the IOMMU code to have only one place to
access the bitmap, in the popular way that other IOMMUs (e.g. POWER and
SPARC) do.
This patch is preparation for modifications to fix the IOMMU segment boundary
problem.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch is preparation for modifications to fix the IOMMU segment boundary
problem.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Adrian Bunk reported another compile error with a SVN head GCC:
...
CC arch/cris/arch-v10/lib/string.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/string.c:138:
error: lvalue required as increment operand
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/string.c:138:
error: lvalue required as increment operand
/home/bunk/linux/kernel-2.6/git/linux-2.6/arch/cris/arch-v10/lib/string.c:139:
error: lvalue required as increment operand
...
This is due to the use of the construct:
*((long*)dst)++ = lc;
Which isn't legal since casts don't return an lvalue.
The solution is to import the implementation from newlib,
which is continually autotested together with GCC mainline,
and uses the construct:
*(long *) dst = lc; dst += 4;
Since this is an import of a file from newlib, I'm not touching
the formatting or correcting any checkpatch errors.
As for the earlier fix for memset.c, even if the two files for
CRIS v10 and CRIS v32 are identical at the moment, it might
be possible to tweak the CRIS v32 version.
Thus, I'm not yet folding them into the same file, at least not
until we've done some research on it.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add CONFIG_HAVE_KRETPROBES to the arch/<arch>/Kconfig file for relevant
architectures with kprobes support. This facilitates easy handling of
in-kernel modules (like samples/kprobes/kretprobe_example.c) that depend on
kretprobes being present in the kernel.
Thanks to Sam Ravnborg for helping make the patch more lean.
Per Mathieu's suggestion, added CONFIG_KRETPROBES and fixed up dependencies.
Signed-off-by: Ananth N Mavinakayanahalli <ananth@in.ibm.com>
Acked-by: Mathieu Desnoyers <mathieu.desnoyers@polymtl.ca>
Acked-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Commit 2f569afd9c
(CONFIG_HIGHPTE vs. sub-page page tables) introduced use of
inc_zone_page_state and dec_zone_page_state in include/linux/mm.h.
Those are defined in include/linux/vmstat.h, but after it includes
mm.h, making it impossible to include vmstat.h since inc_zone_page_state
and dec_zone_page_state then would be undefined.
arch/cris/arch-v10/kernel/time.c does just this, which makes the
CRIS v10 build break with the following error:
...
CC arch/cris/arch-v10/kernel/time.o
In file included from include/linux/vmstat.h:7,
from arch/cris/arch-v10/kernel/time.c:17:
include/linux/mm.h: In function 'pgtable_page_ctor':
include/linux/mm.h:902: error: implicit declaration of function 'inc_zone_page_state'
include/linux/mm.h: In function 'pgtable_page_dtor':
include/linux/mm.h:908: error: implicit declaration of function 'dec_zone_page_state'
make[2]: *** [arch/cris/arch-v10/kernel/time.o] Error 1
make[1]: *** [arch/cris/arch-v10/kernel] Error 2
make: *** [sub-make] Error 2
...
By changing kernel/time.c to include linux/mm.h, the build succeeds.
Signed-off-by: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Mikael Starvik <mikael.starvik@axis.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes the following compile error with a recent gcc:
CC kernel/kprobes.o
/home/bunk/linux/kernel-2.6/git/linux-2.6/kernel/kprobes.c:1066: error: __ksymtab_jprobe_return causes a section type conflict
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This fixes regression introduced in 113134fcbc
Intel Tiger platforms hang when calling SAL_GET_PHYSICAL_ID_INFO
instead of properly returning -1 for unimplemented, so add a
version check.
SGI Altix platforms have an incorrect SAL version hard-coded into
their prom -- they encode 2.9, but actually implement 3.2 -- so
fix it up and allow ia64_sal_get_physical_id_info to keep
working.
Signed-off-by: Alex Chiang <achiang@hp.com>
Acked-by: Russ Anderson <rja@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
This patch moves the default ia64 defconfig to
arch/ia64/configs/generic_defconfig where it belongs and selects it as
the default defconfig through KBUILD_DEFCONFIG.
Signed-off-by: Adrian Bunk <adrian.bunk@movial.fi>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Fix the problem that the following error message is sometimes displayed
at irq migration when vector domain is enabled.
"Unexpected interrupt vector %d on CPU %d is not mapped to any IRQ!"
The cause of this problem is an interrupt is sent to the previous
target CPU after cleaning up vector to irq mapping table. To clean up
vector to irq map on the previous target CPU safty, change the irq
migration in multiple vector domain as follows. The original idea is
from x86 interrupt management code.
- Delay vector to irq table cleanup until the interrupts are sent
to new target CPUs. By this, it is ensured that target CPU is
completely changed on the interrupt controller side.
- Even after the interrupts are sent to new target CPUs, there can
be pended interrupts remaining on the previous target CPU. So we
need to delay clearning up vector to irq table until the pended
interrupt is handled. For this, send IPI to the previous target
CPU with lower priority vector and clean up vector to irq table
in its handler.
This patch affects only to irq migration code with multiple vector
domain is enabled.
Signed-off-by: Kenji Kaneshige <kaneshige.kenji@jp.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The similar check has been added to x86_32(i386) in commit
id 83bd01024b.
So we add this check to ia64_ia32 and improve it a liitle bit in that
we need to check for stack overflow only when the signal is on stack.
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
The similar check has been added to x86_32(i386) in commit
id 83bd01024b.
So we add this check to ia64 and improve it a liitle bit in that
we need to check for stack overflow only when the signal is on stack.
Signed-off-by: Shi Weihua <shiwh@cn.fujitsu.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
Auto select CONFIG_NUMA and CONFIG_ACPI_NUMA when picking SN2, similar
to how they are selected automatically for CONFIG_IA64_GENERIC.
Signed-off-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
P4 has been coming out as CPU_FAMILY=4 instead of 6: fix MPENTIUM4 typo.
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86/xen: fix DomU boot problem
x86: not set node to cpu_to_node if the node is not online
x86, i387: fix ptrace leakage using init_fpu()
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/avi/kvm:
x86: disable KVM for Voyager and friends
KVM: VMX: Avoid rearranging switched guest msrs while they are loaded
KVM: MMU: Fix race when instantiating a shadow pte
KVM: Route irq 0 to vcpu 0 exclusively
KVM: Avoid infinite-frequency local apic timer
KVM: make MMU_DEBUG compile again
KVM: move alloc_apic_access_page() outside of non-preemptable region
KVM: SVM: fix Windows XP 64 bit installation crash
KVM: remove the usage of the mmap_sem for the protection of the memory slots.
KVM: emulate access to MSR_IA32_MCG_CTL
KVM: Make the supported cpuid list a host property rather than a vm property
KVM: Fix kvm_arch_vcpu_ioctl_set_sregs so that set_cr0 works properly
KVM: SVM: set NM intercept when enabling CR0.TS in the guest
KVM: SVM: Fix lazy FPU switching
Construct Xen guest e820 map with a hole between 640K-1M.
It's pure luck that Xen kernels have gotten away with it in the past.
The patch below seems like the right thing to do. It certainly boots in
a domU without the DMI problem (without any of the other related patches
such as Alexander's).
Signed-off-by: Ian Campbell <ijc@hellion.org.uk>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Tested-by: Mark McLoughlin <markmc@redhat.com>
Acked-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
resolve boot problem reported by Mel Gorman:
http://lkml.org/lkml/2008/2/13/404
init_cpu_to_node will use cpu->apic (from MADT or mptable) and
apic->node(from SRAT or AMD config space with k8_bus_64.c) to have
cpu->node mapping, and later identify_cpu will overwrite them
again...(with nearby_node...)
this patch checks if the node is online, otherwise it will not
update cpu_node map. so keep cpu_node map to online node before
identify_cpu..., to prevent possible error.
Signed-off-by: Yinghai Lu <yinghai.lu@sun.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
This bug got introduced by the recent i387 merge:
commit 4421011120
Author: Roland McGrath <roland@redhat.com>
Date: Wed Jan 30 13:31:50 2008 +0100
x86: x86 i387 user_regset
Current usage of unlazy_fpu() in ptrace specific routines is wrong.
unlazy_fpu() will not init fpu if the task never used math. So the
ptrace calls can expose the parent tasks FPU data in some cases.
Replace it with the init_fpu() which will init the math state, if the
task never used math before.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
m68k{,nommu}: Wire up the new timerfd syscalls, which were introduced in
commit 4d672e7ac7 ("timerfd: new timerfd API").
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Most classic Pentiums don't have hardware virtualization extension,
and building kvm with Voyager, Visual Workstation, or NUMAQ
generates spurious failures.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
KVM tries to run as much as possible with the guest msrs loaded instead of
host msrs, since switching msrs is very expensive. It also tries to minimize
the number of msrs switched according to the guest mode; for example,
MSR_LSTAR is needed only by long mode guests. This optimization is done by
setup_msrs().
However, we must not change which msrs are switched while we are running with
guest msr state:
- switch to guest msr state
- call setup_msrs(), removing some msrs from the list
- switch to host msr state, leaving a few guest msrs loaded
An easy way to trigger this is to kexec an x86_64 linux guest. Early during
setup, the guest will switch EFER to not include SCE. KVM will stop saving
MSR_LSTAR, and on the next msr switch it will leave the guest LSTAR loaded.
The next host syscall will end up in a random location in the kernel.
Fix by reloading the host msrs before changing the msr list.
Signed-off-by: Avi Kivity <avi@qumranet.com>
For improved concurrency, the guest walk is performed concurrently with other
vcpus. This means that we need to revalidate the guest ptes once we have
write-protected the guest page tables, at which point they can no longer be
modified.
The current code attempts to avoid this check if the shadow page table is not
new, on the assumption that if it has existed before, the guest could not have
modified the pte without the shadow lock. However the assumption is incorrect,
as the racing vcpu could have modified the pte, then instantiated the shadow
page, before our vcpu regains control:
vcpu0 vcpu1
fault
walk pte
modify pte
fault in same pagetable
instantiate shadow page
lookup shadow page
conclude it is old
instantiate spte based on stale guest pte
We could do something clever with generation counters, but a test run by
Marcelo suggests this is unnecessary and we can just do the revalidation
unconditionally. The pte will be in the processor cache and the check can
be quite fast.
Signed-off-by: Avi Kivity <avi@qumranet.com>
If the local apic initial count is zero, don't start a an hrtimer with infinite
frequency, locking up the host.
Signed-off-by: Avi Kivity <avi@qumranet.com>
the cr3 variable is now inside the vcpu->arch structure.
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
alloc_apic_access_page() can sleep, while vmx_vcpu_setup is called
inside a non preemptable region. Move it after put_cpu().
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
While installing Windows XP 64 bit wants to access the DEBUGCTL and the last
branch record (LBR) MSRs. Don't allowing this in KVM causes the installation to
crash. This patch allow the access to these MSRs and fixes the issue.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
This patch replaces the mmap_sem lock for the memory slots with a new
kvm private lock, it is needed beacuse untill now there were cases where
kvm accesses user memory while holding the mmap semaphore.
Signed-off-by: Izik Eidus <izike@qumranet.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Reported by Adrian Bunk.
Just like in changeset a3f9985843
("[SPARC64]: Move kernel unaligned trap handlers into assembler
file.") we have to move the assembler bits into a seperate
asm file because as far as the compiler is concerned
these inline bits we're doing in unaligned.c are unreachable.
Signed-off-by: David S. Miller <davem@davemloft.net>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86:
x86: revert "x86: fix pmd_bad and pud_bad to support huge pages"
x86: revert "x86: CPA: avoid split of alias mappings"
Revert:
commit 8be8f54bae
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Sat Feb 23 20:43:21 2008 +0100
x86: CPA: avoid split of alias mappings
because it clearly mishandles the case when __change_page_attr(), called
from __change_page_attr_set_clr(), changes cpa->processed to 1 and
cpa_process_alias(cpa) is executed right after that.
This crashes my x86-64 test box early in the boot process
(ref. http://bugzilla.kernel.org/show_bug.cgi?id=10140#c4).
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Injecting an GP when accessing this MSR lets Windows crash when running some
stress test tools in KVM. So this patch emulates access to this MSR.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
One of the use cases for the supported cpuid list is to create a "greatest
common denominator" of cpu capabilities in a server farm. As such, it is
useful to be able to get the list without creating a virtual machine first.
Since the code does not depend on the vm in any way, all that is needed is
to move it to the device ioctl handler. The capability identifier is also
changed so that binaries made against -rc1 will fail gracefully.
Signed-off-by: Avi Kivity <avi@qumranet.com>
Whilst working on getting a VM to initialize in to IA32e mode I found
this issue. set_cr0 relies on comparing the old cr0 to the new one to
work correctly. Move the assignment below so the compare can work.
Signed-off-by: Paul Knowles <paul@transitive.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
Explicitly enable the NM intercept in svm_set_cr0 if we enable TS in the guest
copy of CR0 for lazy FPU switching. This fixes guest SMP with Linux under SVM.
Without that patch Linux deadlocks or panics right after trying to boot the
other CPUs.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
If the guest writes to cr0 and leaves the TS flag at 0 while vcpu->fpu_active
is also 0, the TS flag in the guest's cr0 gets lost. This leads to corrupt FPU
state an causes Windows Vista 64bit to crash very soon after boot. This patch
fixes this bug.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Markus Rechberger <markus.rechberger@amd.com>
Signed-off-by: Avi Kivity <avi@qumranet.com>
The only tricky part is we need to adjust the PTE insertion loop to
cater for holes in the page table. The PTEs for each segment start on
a 4K boundary, so with 16M pages we have 16 PTEs per segment and then
a gap to the next 4K page boundary.
It might be possible to allocate the PTEs for each segment separately,
saving the memory currently filling the gaps. However we'd need to
check that's OK with the hardware, and that it actually saves memory.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Make some preliminary changes to cell_iommu_alloc_ptab() to allow it to
take the page size as a parameter rather than assuming IOMMU_PAGE_SIZE.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
We use n_pte_pages to calculate the stride through the page tables, but
we also use it to set the NPPT value in the segment table entry. That is
defined as the number of 4K pages per segment, so we should calculate
it as such regardless of the IOMMU page size.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Currently the cell IOMMU code allocates the entire IOMMU page table in a
contiguous chunk. This is nice and tidy, but for machines with larger
amounts of RAM the page table allocation can fail due to it simply being
too large.
So split the segment table and page table setup routine, and arrange to
have the dynamic and fixed page tables allocated separately.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
There's no need to allocate the pad page unless we're going to actually
use it - so move the allocation to where we know we're going to use it.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The cell IOMMU code no longer needs to save the pte_offset variable
separately, it is incorporated into tbl->it_offset.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
The cell IOMMU tce build and free routines use pte_offset to convert
the index passed from the generic IOMMU code into a page table offset.
This takes into account the SPIDER_DMA_OFFSET which sets the top bit
of every DMA address.
However it doesn't cater for the IOMMU window starting at a non-zero
address, as the base of the window is not incorporated into pte_offset
at all.
As it turns out tbl->it_offset already contains the value we need, it
takes into account the base of the window and also pte_offset. So use
it instead!
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
It's called the fixed mapping, not the static mapping.
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Ulrich Weigand has found that the hardware watchpoints on cell were not
working back in November :
http://ozlabs.org/pipermail/linuxppc-dev/2007-November/046135.html
This patch sets them during initialization.
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This moves the private DABRX definitions for celleb from beat.h to
reg.h to make them usable for all.
Signed-off-by: Jens Osterkamp <jens@de.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
This patch enables OProfile callgraph support for the Cell processor. The
original code was just calling a function to add the PC value, now it will
call a function that first checks the callgraph depth. Callgraph is already
enabled on the other Power platforms.
Signed-off-by: Bob Nelson <rrnelson@us.ibm.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Since 2f569af (CONFIG_HIGHPTE vs. sub-page page tables.) pte_free() calls
pte_lock_deinit() and dec_zone_page_state(). So free_pgd_slow must not call
the latter two when calling the first.
Signed-off-by: Uwe Kleine-König <Uwe.Kleine-Koenig@digi.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This is unnecessary since it is already protected by
spin_lock_irq{save, restore} in clock.c.
Signed-off-by: eric miao <eric.miao@marvell.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
"cat /dev/mem" may cause kernel Oops for boards with PHYS_OFFSET != 0
because character device is mapped to addresses starting from zero
and there is no protection against such situation.
Patch just add this.
Signed-off-by: Alexandre Rusev <arusev@ru.mvista.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert debug-only (and removed) MODULE_PARM() to module_param().
Compiles cleanly (with DEBUG=1).
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On Wed, Feb 20, 2008 at 11:50:33AM +0100, Guennadi Liakhovetski wrote:
> arch/arm/kernel/atags.c uses for some reason the
> KEXEC_BOOT_PARAMS_SIZE macro, which is only defined if CONFIG_KEXEC
> is set. So, either this macro should be defined always, or another
> macro should be used, or ATAGS_PROC should depend on KEXEC.
As the procfs export of ATAGS is not meant as a stable, general purpose
ABI it shouldn't be an independent, general configuration option.
This patch make ATAGS_PROC depend on KEXEC
Signed-off-by: Uli Luckas <u.luckas@road.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix 32-on-64 pvops kernel:
we don't want userspace using syscall/sysenter, even if the hypervisor
supports it, so mask it out from CPUID.
Signed-off-by: Jeremy Fitzhardinge <jeremy@xensource.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
revert the BTS ptrace extension for now.
based on general objections from Roland McGrath:
http://lkml.org/lkml/2008/2/21/323
we'll let the BTS functionality cook some more and re-enable
it in v2.6.26. We'll leave the dead code around to help the
development of this code.
(X86_BTS is not defined at the moment)
Signed-off-by: Ingo Molnar <mingo@elte.hu>
avoid over-eager large page splitup.
When the target area needs to be split or is split already (ioremap)
then the current code enforces the split of large mappings in the alias
regions even if we could avoid it.
Use a separate variable processed in the cpa_data structure to carry
the number of pages which have been processed instead of reusing the
numpages variable. This keeps numpages intact and gives the alias code
a chance to keep large mappings intact.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
delay the removal of this symbol export by one more kernel release,
giving external modules such as VirtualBox a chance to stop using it.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Jan Beulich noticed it during code review that if a driver's ioremap()
fails (say due to -ENOMEM) then we might leak the struct vm_area.
Free it properly.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Priit Laes discovered that the sed command processing nm output was
sensitive to locale settings. This was addressed in commit
03994f01e8 by using [:alnum:] in place of
[a-zA-Z0-9].
But that solution too is locale-dependent and may not always match
the identifiers it needs to. The better fix is just to run sed et al
with a fixed locale setting in all builds.
Signed-off-by: Roland McGrath <roland@redhat.com>
CC: Priit Laes <plaes@plaes.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
a recent fix:
commit ce28b9864b
Author: Thomas Gleixner <tglx@linutronix.de>
Date: Wed Feb 20 23:57:30 2008 +0100
x86: fix vsyscall wreckage
removed the broken /kernel/vsyscall64 handler completely.
This triggers the following debug check:
sysctl table check failed: /kernel/vsyscall64 No proc_handler
Restore the sane part of the proc handler.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix a kernel bug (vmware boot problem) reported by Tomasz Grobelny,
which occurs with certain .config variants and gccs.
The x86 TLS cleanup in commit efd1ca52d0
made the sys_set_thread_area and sys_get_thread_area functions ripe for
tail call optimization. If the compiler chooses to use it for them, it
can clobber the user trap frame because these are asmlinkage functions.
Reported-by: Tomasz Grobelny <tomasz@grobelny.oswiecenia.net>
Signed-off-by: Roland McGrath <roland@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/cooloney/blackfin-2.6: (35 commits)
Blackfin Serial Driver: Fix bug - Only insert UART rx char in timer task.
Blackfin Serial Driver: Fix bug - update tx dma buffer tail before wake up processes.
Blackfin Serial Driver: Fix bug - Increase buffer tail immediately before starting tx dma.
[Blackfin] serial driver: Add flow control support to bf54x
[Blackfin] serial driver: Fix bug Poll RTS/CTS status in DMA mode as well
[Blackfin] serial driver: ADSP-BF52x arch/mach support
[Blackfin] serial driver: use simpler comment headers and strip out information that is maintained in the scm's log
[Blackfin] serial driver: rework break flood anomaly handling to be more robust/realistic about what we can actually work around
[Blackfin] serial driver: fix bug - cache the bits of the LSR on systems where the LSR is read-to-clear
[Blackfin] serial driver: fix bug - should not wait for the TFI bit, just clear it when tx stop.
[Blackfin] serial driver: Fix bug serial driver in DMA mode spams history to console on shell restart
[Blackfin] serial driver: Fix bug Free rx dma buffer in shutdown.
[Blackfin] serial driver: Clean up UART DMA code.
Blackfin Serial driver: Fix bug - serial driver in PIO mode cant handle input very quickly
[Blackfin] arch: kill section mismatch warnings
[Blackfin] arch: handle the most common L1 shrinkage case (L1 does not exist for a part) so that any parts labeled for L1 instead get placed into external memory sections
[Blackfin] arch: add bfin_clear_PPIx_STATUS() helper funcs like we have for other parts
[Blackfin] arch: make sure we have proper description/copyright/license lines
[Blackfin] arch: Fix CONFIG_PM support for BF561
[Blackfin] arch: Remove DPMC char driver option
...
* git://git.kernel.org/pub/scm/linux/kernel/git/lethal/sh-2.6:
arch/sh/drivers/dma/dma-sh.c: Correct use of ! and &
serial: Move asm-sh/sci.h to linux/serial_sci.h.
sh: Fix up HAS_SR_RB typo in entry-macros.
maple: fix device detection
sh: fix rtc_resources setup for sh770x
sh: heartbeat: ioremap is expected to succeed
sh: Storage class should be before const qualifier
maple: remove unused variable
sh: SH5-103 needs to select CPU_SH5.
sh: Rename SH-3 CCR3 reg to avoid synclink_cs clash.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc-2.6:
[SPARC64]: Adjust kernel PC validation test in fault handler.
[SPARC64]: Loosen checks in exception table handling.
[SPARC64]: Fix section mismatch from kernel_map_range
[SPARC64]: Fix section mismatchs from dr_cpu_data
[SPARC]: Fix build in arch/sparc/kernel/led.c
The spu_runcntl_RW register is restored within spu_restore function.
So, at the end of spu_bind_context, the SPU context is not just loaded,
but running.
This change corrects the state switch to account the time as USER.
Signed-off-by: Andre Detsch <adetsch@br.ibm.com>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Because of the new futex validation init handler, we have
to accept faults in init section text as well as the normal
kernel text.
Thanks to Tom Callaway for the bug report.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a potential race between flushes of the entire SLB in the MFC
and the point where new entries are being established. The problem is
that we might put a ESID entry into the MFC SLB when the VSID entry has
just been cleared by the global flush.
This can be circumvented by holding the register_lock throughout both
the flushing and the creation of SLB entries.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
When we replace an SLB entry in the MFC after using up all the available
entries, there is a short window in which an incorrect entry is marked
as valid.
The problem is that the 'valid' bit is stored in the ESID, which is
always written after the VSID. Overwriting the VSID first will make the
original ESID entry point to the new VSID, which means that any
concurrent DMA accessing the old ESID ends up being redirected to the
new virtual address. A few cycles later, we write the new ESID and
everything is fine again.
That race can be closed by writing a zero entry to the ESID first, which
makes sure that the VSID is not accessed until we write the new ESID.
Note that we don't actually need to invalidate the SLB entry using the
invalidation register, which would also flush any ERAT entries for that
segment, because the segment translation does not become invalid but is
only removed from the SLB cache.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
There is a small race between the context save procedure
and the SPU interrupt handling, where we expect all interrupt
processing to have finished after disabling them, while
an interrupt is still being processed on another CPU.
The obvious fix is to call synchronize_irq() after disabling
the interrupts at the start of the context save procedure
to make sure we never access the SPU any more during an
ongoing save or even after that.
Thanks to Benjamin Herrenschmidt for pointing this out.
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Currently, we get the following output from sputrace:
[5.097935954] 1606: spufs_ps_nopfn__enter (thread = 1605, spu = -1)
[5.097958164] 1606: spufs_ps_nopfn__insert (thread = 1605, spu = 15)
[5.097973529] 1607: spufs_ps_nopfn__enter (thread = 1605, spu = -1)
[5.097989174] 1607: spufs_ps_nopfn__insert (thread = 1605, spu = 14)
Which leads me to believe that 160[67] is the current thread ID, and
1605 is the context backing the psmap.
However, the 'current' and 'owner' tids are reversed - the 'current'
tid is on the right. This change puts the current thread ID in the
left-hand column instead, and renames the right to 'ctxthread'.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Correct the remaining 44x cuboot wrappers to define TARGET_4xx as well. This
creates the correct structure to use, including things like the second MAC
address.
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
At present, we have a situation where a context with no owner is
re-scheduled by spu_forget:
Thread 1: reading regs file Thread 2: context owner
spu_forget()
- ctx->owner = NULL
- set SPU_SCHED_WAS_ACTIVE
spu_acquire_saved()
- context is in saved state
spu_release_saved()
- SPU_SCHED_WAS_ACTIVE is set,
so spu_activate() the context,
which now has no owner
In spu_forget(), we shouldn't be requesting a re-schedule by setting
SPU_SCHED_WAS_ACTIVE. This change removes the set_bit in spu_forget(),
so that spu_release_saved() doesn't reinsert this destroyed context on
to the run queue.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
In order to get the proper boad info (bd_info) structure defined in ppcboot.h
both TARGET_4xx and TARGET_44x should be defined for all PowerPC 440 boards.
The 440GX boards also need TARGET_440GX defined since they have 4 EMACs and
there are 4 MAC addesses in bd_info passed by u-boot.
Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
This patch changes the katmai (440SPe) L1 cache size to 32k. Some
whitespace issues are cleaned up too.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Since the 4xx PCIe driver checks for 405ex compatibility, the
PCIe interface was not detected as it is currently defined as
"405exr" compatible. This patch changes it to "405ex".
The 405EX and 405EXr are identical exept that the 2nd PCIe and the
2nd EMAC interfaces are missing.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Iff the parent has TIF_DEBUG set, _and_ clone_flags includes
CLONE_PTRACE we should set the TIF_DEBUG flag for the child and
increment the ocd refcount. Otherwise, the TIF_DEBUG flag must be
unset.
Currently, the child inherits TIF_DEBUG from the parent before
copy_thread is called, so TIF_DEBUG may be already be set before we
determine whether the child is supposed to inherit debugging
capabilities from the parent or not. This means that ocd_enable()
won't increment the refcount, because TIF_DEBUG is already set, and
that TIF_DEBUG will be set for processes that aren't being debugged.
This leads to a refcounting asymmetry, which may show up as
------------[ cut here ]------------
Badness at arch/avr32/kernel/ocd.c:73
PC is at ocd_disable+0x34/0x60
LR is at put_lock_stats+0xa/0x20
as reported by David Brownell. Happens when strace'ing a process that
forks a new child process, e.g. "strace mount -tjffs2 mtd1 /mnt", and
subsequently killing the child process (e.g. "umount /mnt".)
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
We have a small window where a spu context may be destroyed while
we're servicing a page fault (from another thread) to the context's
problem state mapping.
After we up_read() the mmap_sem, it's possible that the context is
destroyed by its owning thread, and so the later references to ctx
are invalid. This can maifest as a deadlock on the (now free()-ed)
context state mutex.
This change adds a reference to the context before we release the
mmap_sem, so that the context cannot be destroyed.
Signed-off-by: Jeremy Kerr <jk@ozlabs.org>
Some parts of the kernel now do things like do *_user() accesses while
set_fs(KERNEL_DS) that fault on purpose.
See, for example, the code added by changeset
a0c1e9073e ("futex: runtime enable pi
and robust functionality").
That trips up the ASI sanity checking we make in do_kernel_fault().
Just remove it for now. Maybe we can add it back later with an added
conditional which looks at the current get_fs() value.
Signed-off-by: David S. Miller <davem@davemloft.net>
In commit e6bafba5b4, a bug was fixed that
involved converting !x & y to !(x & y). The code below shows the same
pattern, and thus should perhaps be fixed in the same way.
This is not tested and clearly changes the semantics, so it is only
something to consider.
The semantic patch that makes this change is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ expression E1,E2; @@
(
!E1 & !E2
|
- !E1 & E2
+ !(E1 & E2)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/x86/linux-2.6-x86: (24 commits)
x86: no robust/pi futex for real i386 CPUs
x86: fix boot failure on 486 due to TSC breakage
x86: fix build on non-C locales.
x86: make c_idle.work have a static address.
x86: don't save unreliable stack trace entries
x86: don't make swapper_pg_pmd global
x86: don't print a warning when MTRR are blank and running in KVM
x86: fix execve with -fstack-protect
x86: fix vsyscall wreckage
x86: rename KERNEL_TEXT_SIZE => KERNEL_IMAGE_SIZE
x86: fix spontaneous reboot with allyesconfig bzImage
x86: remove double-checking empty zero pages debug
x86: notsc is ignored on common configurations
x86/mtrr: fix kernel-doc missing notation
x86: handle BIOSes which terminate e820 with CF=1 and no SMAP
x86: add comments for NOPs
x86: don't use P6_NOPs if compiling with CONFIG_X86_GENERIC
x86: require family >= 6 if we are using P6 NOPs
x86: do not promote TM3x00/TM5x00 to i686-class
x86: hpet fix docbook comment
...
> Diffing dmesg between git7 and git8 doesn't sched any light since
> git8 also removed the printouts of the x86 caps as they were being
> initialised and updated. I'm currently adding those printouts back
> in the hope of seeing where and when the caps get broken.
That turned out to be very illuminating:
--- dmesg-2.6.24-git7 2008-02-24 18:01:25.295851000 +0100
+++ dmesg-2.6.24-git8 2008-02-24 18:01:25.530358000 +0100
...
CPU: After generic identify, caps: 00000003 00000000 00000000 00000000 00000000 00000000 00000000 00000000
CPU: After all inits, caps: 00000003 00000000 00000000 00000000 00000000 00000000 00000000 00000000
+CPU: After applying cleared_cpu_caps, caps: 00000013 00000000 00000000 00000000 00000000 00000000 00000000 00000000
Notice how the TSC cap bit goes from Off to On.
(The first two lines are printout loops from -git7 forward-ported
to -git8, the third line is the same printout loop added just after
the xor-with-cleared_cpu_caps[] loop.)
Here's how the breakage occurs:
1. arch/x86/kernel/tsc_32.c:tsc_init() sees !cpu_has_tsc,
so bails and calls setup_clear_cpu_cap(X86_FEATURE_TSC).
2. include/asm-x86/cpufeature.h:setup_clear_cpu_cap(bit) clears
the bit in boot_cpu_data and sets it in cleared_cpu_caps
3. arch/x86/kernel/cpu/common.c:identify_cpu() XORs all caps
in with cleared_cpu_caps
HOWEVER, at this point c->x86_capability correctly has TSC
Off, cleared_cpu_caps has TSC On, so the XOR incorrectly
sets TSC to On in c->x86_capability, with disastrous results.
The real bug is that clearing bits with XOR only works if the
bits are known to be 1 prior to the XOR, and that's not true here.
A simple fix is to convert the XOR to AND-NOT instead. The following
patch does that, and allows my 486 to boot 2.6.25-rc kernels again.
[ mingo@elte.hu: fixed a similar bug in setup_64.c as well. ]
The breakage was introduced via commit 7d851c8d3d.
Signed-off-by: Mikael Pettersson <mikpe@it.uu.se>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
For some locales regex range [a-zA-Z] does not work as it is supposed to.
so we have to use [:alnum:] and [:xdigit:] to make it work as intended.
[1] http://en.wikipedia.org/wiki/Estonian_alphabet
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently, c_idle is declared in the stack, and thus, have no static address.
Peter Zijlstra points out this simple solution, in which c_idle.work
is initializated separatedly. Note that the INIT_WORK macro has a static
declaration of a key inside.
Signed-off-by: Glauber Costa <gcosta@redhat.com>
Acked-by: Peter Zijlstra <pzijlstr@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently, there is no way for print_stack_trace() to determine whether
a given stack trace entry was deemed reliable or not, simply because
save_stack_trace() does not record this information. (Perhaps needless
to say, this makes the saved stack traces A LOT harder to read, and
probably with no other benefits, since debugging features that use
save_stack_trace() most likely also require frame pointers, etc.)
This patch reverts to the old behaviour of only recording the reliable trace
entries for saved stack traces.
Signed-off-by: Vegard Nossum <vegardno@ifi.uio.no>
Acked-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There doesn't seem to be any reason for swapper_pg_pmd being global.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Inside a KVM virtual machine the MTRRs are usually blank. This confuses Linux
and causes a warning message at boot. This patch removes that warning message
when running Linux as a KVM guest.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
pointed out by pageexec@freemail.hu:
> what happens here is that gcc treats the argument area as owned by the
> callee, not the caller and is allowed to do certain tricks. for ssp it
> will make a copy of the struct passed by value into the local variable
> area and pass *its* address down, and it won't copy it back into the
> original instance stored in the argument area.
>
> so once sys_execve returns, the pt_regs passed by value hasn't at all
> changed and its default content will cause a nice double fault (FWIW,
> this part took me the longest to debug, being down with cold didn't
> help it either ;).
To fix this we pass in pt_regs by pointer.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
based on a report from Arne Georg Gleditsch about user-space apps
misbehaving after toggling /proc/sys/kernel/vsyscall64, a review
of the code revealed that the "NOP patching" done there is
fundamentally unsafe for a number of reasons:
1) the patching code runs without synchronizing other CPUs
2) it inserts NOPs even if there is no clock source which provides vread
3) when the clock source changes to one without vread we run in
exactly the same problem as in #2
4) if nobody toggles the proc entry from 1 to 0 and to 1 again, then
the syscall is not patched out
as a result it is possible to break user-space via this patching.
The only safe thing for now is to remove the patching.
This code was broken since v2.6.21.
Reported-by: Arne Georg Gleditsch <arne.gleditsch@dolphinics.no>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The KERNEL_TEXT_SIZE constant was mis-named, as we not only map the kernel
text but data, bss and init sections as well.
That name led me on the wrong path with the KERNEL_TEXT_SIZE regression,
because i knew how big of _text_ my images have and i knew about the 40 MB
"text" limit so i wrongly thought to be on the safe side of the 40 MB limit
with my 29 MB of text, while the total image size was slightly above 40 MB.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
recently the 64-bit allyesconfig bzImage kernel started spontaneously
rebooting during early bootup.
after a few fun hours spent with early init debugging, it turns out
that we've got this rather annoying limit on the size of the kernel
image:
#define KERNEL_TEXT_SIZE (40*1024*1024)
which limit my vmlinux just happened to pass:
text data bss dec hex filename
29703744 4222751 8646224 42572719 2899baf vmlinux
40 MB is 42572719 bytes, so my vmlinux was just 1.5% above this limit :-/
So it happily crashed right in head_64.S, which - as we all know - is
the most debuggable code in the whole architecture ;-)
So increase the limit to allow an up to 128MB kernel image to be mapped.
(should anyone be that crazy or lazy)
We have a full 4K of pagetable (level2_kernel_pgt) allocated for these
mappings already, so there's no RAM overhead and the limit was rather
pointless and arbitrary.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
notsc is ignored in 32-bit kernels if CONFIG_X86_TSC is on.. which is
bad, fix it.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix mtrr kernel-doc warning:
Warning(linux-2.6.24-git12//arch/x86/kernel/cpu/mtrr/main.c:677): No description found for parameter 'end_pfn'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The proper way to terminate the e820 chain is with %ebx == 0 on the
last legitimate memory block. However, several BIOSes don't do that
and instead return error (CF = 1) when trying to read off the end of
the list. For this error return, %eax doesn't necessarily return the
SMAP signature -- correctly so, since %ah should contain an error code
in this case.
To deal with some particularly broken BIOSes, we clear the entire e820
chain if the SMAP signature is missing in the middle, indicating a
plain insane e820 implementation. However, we need to make the test
for CF = 1 before the SMAP check.
This fixes at least one HP laptop (nc6400) for which none of the
memory-probing methods (e820, e801, 88) functioned fully according to
spec.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
P6_NOPs are definitely not supported on some VIA CPUs, and possibly
(unverified) on AMD K7s. It is also the only thing that prevents a
686 kernel from running on Transmeta TM3x00/5x00 (Crusoe) series.
The performance benefit over generic NOPs is very small, so when
building for generic consumption, avoid using them.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The P6 family of NOPs are only available on family >= 6 or above, so
enforce that in the boot code.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We have been promoting Transmeta TM3x00/TM5x00 chips to i686-class
based on the notion that they contain all the user-space visible
features of an i686-class chip. However, this is not actually true:
they lack the EA-taking long NOPs (0F 1F /0). Since this is a
userspace-visible incompatibility, downgrade these CPUs to the
manufacturer-defined i586 level.
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Use PF_MEMALLOC to prevent recursive calls in the DBEUG_PAGEALLOC
case. This makes the code simpler and more robust against allocation
failures.
This fixes the following fallback to non-mmconfig:
http://lkml.org/lkml/2008/2/20/551http://bugzilla.kernel.org/show_bug.cgi?id=10083
Also, for DEBUG_PAGEALLOC=n reduce the pool size to one page.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Hi all,
Beginning from commits close to v2.6.25-rc2, running lguest always oopses
the host kernel. Oops is at [1].
Bisection led to the following commit:
commit 37cc8d7f96
x86/early_ioremap: don't assume we're using swapper_pg_dir
At the early stages of boot, before the kernel pagetable has been
fully initialized, a Xen kernel will still be running off the
Xen-provided pagetables rather than swapper_pg_dir[]. Therefore,
readback cr3 to determine the base of the pagetable rather than
assuming swapper_pg_dir[].
static inline pmd_t * __init early_ioremap_pmd(unsigned long addr)
{
- pgd_t *pgd = &swapper_pg_dir[pgd_index(addr)];
+ /* Don't assume we're using swapper_pg_dir at this point */
+ pgd_t *base = __va(read_cr3());
+ pgd_t *pgd = &base[pgd_index(addr)];
pud_t *pud = pud_offset(pgd, addr);
pmd_t *pmd = pmd_offset(pud, addr);
Trying to analyze the problem, it seems on the guest side of lguest,
%cr3 has a different value from &swapper_pg-dir (which
is AFAIK fine on a pravirt guest):
Putting some debugging messages in early_ioremap_pmd:
/* Appears 3 times */
[ 0.000000] ***************************
[ 0.000000] __va(%cr3) = c0000000, &swapper_pg_dir = c02cc000
[ 0.000000] ***************************
After 8 hours of debugging and staring on lguest code, I noticed something
strange in paravirt_ops->set_pmd hypercall invocation:
static void lguest_set_pmd(pmd_t *pmdp, pmd_t pmdval)
{
*pmdp = pmdval;
lazy_hcall(LHCALL_SET_PMD, __pa(pmdp)&PAGE_MASK,
(__pa(pmdp)&(PAGE_SIZE-1))/4, 0);
}
The first hcall parameter is global pgdir which looks fine. The second
parameter is the pmd index in the pgdir which is suspectful.
AFAIK, calculating the index of pmd does not need a divisoin over four.
Removing the division made lguest work fine again . Patch is at [2].
I am not sure why the division over four existed in the first place. It
seems bogus, maybe the Xen patch just made the problem appear ?
[2]: The patch:
[PATCH] lguest: fix pgdir pmd index cacluation
Remove an error in index calculation which leads to removing
a not existing shadow page table (leading to a Null dereference).
Signed-off-by: Ahmed S. Darwish <darwish.07@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Added a declaration to asm-x86/lguest.h and moved the extern arrays there
as well. As an alternative to including asm/lguest.h directly, an
include could be put in linux/lguest.h
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Cc: "rusty@rustcorp.com.au" <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This header is needed on other architectures as well (namely h8300),
which currently fails to build without this in place. Rather than
duplicating the port definition completely there, just move this to a
common location instead.
This should get h8300 working again for 2.6.25, in addition to the
changes already pushed by Sato-san in -rc2.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Commit e036eaa681 broke dreamcast pci, this
patch fixes that by reverting the dreamcast specific bits.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: Adrian McMenamin <adrian@mcmen.demon.co.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix the RTC resources setup for sh770x. Whit these proper
start values RTC driver (drivers/rtc/rtc-sh.c) works.
Signed-off-by: Rafael Ignacio Zurita <rizurita@yahoo.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Avoids sparse warnings:
kernel/sched.c:2170:17: warning: symbol 'schedule_tail' was not declared. Should it be static?
Avoids the need for an external declaration in arch/um/process.c
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Without this, it's possible to have CONFIG_SUPERH32=y set on SH5-103
parts, which leads to much build badness.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
drivers/char/pcmcia/synclink_cs.c:284:1: warning: "CCR3" redefined
In file included from include/asm/cache.h:13,
from include/asm/processor_32.h:15,
from include/asm/processor.h:60,
from include/linux/prefetch.h:14,
from include/linux/list.h:8,
from include/linux/module.h:9,
from drivers/char/pcmcia/synclink_cs.c:38:
include/asm/cpu/cache.h:38:1: warning: this is the location of the previous definition
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix following warnings:
WARNING: vmlinux.o(.text+0x4f980): Section mismatch in reference from the function kernel_map_range() to the function .init.text:__alloc_bootmem()
WARNING: vmlinux.o(.text+0x4f9cc): Section mismatch in reference from the function kernel_map_range() to the function .init.text:__alloc_bootmem()
alloc_bootmem() is only used during early init and for any subsequent
call to kernel_map_range() the program logic avoid the call.
So annotate kernel_map_range() with __ref to tell modpost to
ignore the reference to a __init function.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix following warnings:
WARNING: vmlinux.o(.text+0x4b258): Section mismatch in reference from the function dr_cpu_data() to the function .devinit.text:mdesc_fill_in_cpu_data()
WARNING: vmlinux.o(.text+0x4b290): Section mismatch in reference from the function dr_cpu_data() to the function .cpuinit.text:cpu_up()
mdesc_fill_in_cpu_data() is only used during early init and for
cpu hotplug so the __cpuinit annotation is the correct choice.
We have the call chain:
dr_cpu_data() => dr_cpu_configure() => mdesc_fill_in_cpu_data()
dr_cpu_data() is used only during early init and for cpu
hotplug. So annotating them all __cpuinit solves the
section mismatch and should be correct.
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
CC [M] arch/sparc/kernel/led.o
arch/sparc/kernel/led.c: In function 'led_blink':
arch/sparc/kernel/led.c:35: error: invalid use of undefined type 'struct
timer_list'
arch/sparc/kernel/led.c:35: error: 'jiffies' undeclared (first use in
this function)
arch/sparc/kernel/led.c:35: error: (Each undeclared identifier is
reported only once
arch/sparc/kernel/led.c:35: error: for each function it appears in.)
arch/sparc/kernel/led.c:36: error: 'avenrun' undeclared (first use in
this function)
arch/sparc/kernel/led.c:36: error: 'FSHIFT' undeclared (first use in
this function)
arch/sparc/kernel/led.c:36: error: 'HZ' undeclared (first use in this
function)
arch/sparc/kernel/led.c:37: error: invalid use of undefined type 'struct
timer_list'
arch/sparc/kernel/led.c:39: error: invalid use of undefined type 'struct
timer_list'
arch/sparc/kernel/led.c:40: error: invalid use of undefined type 'struct
timer_list'
arch/sparc/kernel/led.c:42: error: implicit declaration of function
'add_timer'
arch/sparc/kernel/led.c: In function 'led_write_proc':
arch/sparc/kernel/led.c:70: error: implicit declaration of function
'copy_from_user'
arch/sparc/kernel/led.c:84: error: implicit declaration of function
'del_timer_sync'
arch/sparc/kernel/led.c: In function 'led_init':
arch/sparc/kernel/led.c:109: error: implicit declaration of function
'init_timer'
arch/sparc/kernel/led.c:110: error: invalid use of undefined type
'struct timer_list'
make[1]: *** [arch/sparc/kernel/led.o] Error 1
Based upon original patch by Robert Reif.
Signed-off-by: David S. Miller <davem@davemloft.net>
Each call to i2c_get_adapter() must be followed by a call to
i2c_put_adapter() to release the grabbed reference. Otherwise the
reference count grows forever and the adapter can never be
unregistered.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Vladimir Ananiev <vovan888@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
mpc52xx_set_psc_clkdiv is needed by PSC device drivers.
Signed-off-by: Eric Dujardin <eric.dujardin@sagem.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit ee3d9bd4de ("uml: simplify SIGSEGV
handling"), while greatly simplifying the kernel SIGSEGV handler that
runs in the process address space, introduced a bug which corrupts FP
state in the process.
Previously, the SIGSEGV handler called the sigreturn system call by hand - it
couldn't return through the restorer provided to it because that could try to
call the libc restorer which likely wouldn't exist in the process address
space. So, it blocked off some signals, including SIGUSR1, on entry to the
SIGSEGV handler, queued a SIGUSR1 to itself, and invoked sigreturn. The
SIGUSR1 was delivered, and was visible to the UML kernel after sigreturn
finished.
The commit eliminated the signal masking and the call to sigreturn. The
handler simply hits itself with a SIGTRAP to let the UML kernel know that it
is finished. UML then restores the process registers, which effectively
longjmps the process out of the signal handler, skipping sigreturn's restoring
of register state and the signal mask.
The bug is that the host apparently sets used_fp to 0 when it saves the
process FP state in the sigcontext on the process signal stack. Thus, when
the process is longjmped out of the handler, its FP state is corrupt because
it wasn't saved on the context switch to the UML kernel.
This manifested itself as sleep hanging. For some reason, sleep uses floating
point in order to calculate the sleep interval. When a page fault corrupts
its FP state, it is faked into essentially sleeping forever.
This patch saves the FP state before entering the SIGSEGV handler and restores
it afterwards.
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
In commit 1aa351a308 ("uml: tidy helper
code") the arguments of helper_wait() were changed. The adaptation of
harddog_user.c was forgotten, so this errors occur:
/arch/um/drivers/harddog_user.c: In function 'start_watchdog':
/arch/um/drivers/harddog_user.c:82: error: too many arguments to function 'helper_wait'
/arch/um/drivers/harddog_user.c:89: error: too many arguments to function 'helper_wait'
Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The macros which extract registers from a struct sigcontext are no longer
needed and can be removed. They are starting not to build anyway, given the
removal of the 'e' and 'r' from register names during the x86 merge.
Cc: Jiri Olsa <olsajiri@gmail.com>
Signed-off-by: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Define HZ as a config option.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Fix a shadowed variable in arch/um/kernel/mem.c, since there is a global
variable has the same name.
Cc: Jeff Dike <jdike@linux.intel.com>
Signed-off-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Vitaly Bordug