This patch adds a new SPI driver to support the Altera SOPC Builder
SPI component. It uses the bitbanging library.
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support of OpenCores tiny SPI driver.
http://opencores.org/project,tiny_spi
Signed-off-by: Thomas Chou <thomas@wytron.com.tw>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The Atheros AR71XX/AR724X/AR913X SoCs have a built-in SPI controller. This
patch implements a driver for that.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: spi-devel-general@lists.sourceforge.net
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: linux-mips@linux-mips.org
Cc: Imre Kaloz <kaloz@openwrt.org>
Cc: Luis R. Rodriguez <lrodriguez@atheros.com>
Cc: Cliff Holden <Cliff.Holden@Atheros.com>
Cc: Kathy Giori <Kathy.Giori@Atheros.com>
Patchwork: https://patchwork.linux-mips.org/patch/1960/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
* 'spi' of git://git.linutronix.de/users/bigeasy/soda into spi/next
spi/pxa2xx: register driver properly
spi/pxa2xx: add support for shared IRQ handler
spi/pxa2xx: Use define for SSSR_TFL_MASK instead of plain numbers
arm/pxa2xx: reorgazine SSP and SPI header files
spi/pxa2xx: Add CE4100 support
spi/pxa2xx: Consider CE4100's FIFO depth
spi/pxa2xx: Add chipselect support for Sodaville
spi/pxa2xx: Modify RX-Tresh instead of busy-loop for the remaining RX bytes.
spi/pxa2xx: pass of_node to spi device and set a parent device
dw_spi driver in upstream only supports PIO mode, and this patch
will support it to cowork with the Designware dma controller used
on Intel Moorestown platform, at the same time it provides a general
framework to support dw_spi core to cowork with dma controllers on
other platforms
It has been tested with a Option GTM501L 3G modem and Infenion 60x60
modem. To use DMA mode, DMA controller 2 of Moorestown has to be enabled
Also change the dma interface suggested by Linus Walleij.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
[Typo fix and renames to match intel_mid_dma renaming]
Signed-off-by: Vinod Koul <vinod.koul@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Sodaville's SPI controller is very much the same as in PXA25x. The
difference:
- The RX/TX FIFO is only 4 words deep instead of 16
- No DMA support
- The SPI controller offers a CS functionality
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Now that the of_platform_bus_type has been merged with the platform
bus type, a single platform driver can handle both OF and non-OF use
cases. This patch merges the OF support into the platform driver.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Michal Simek <monstr@monstr.eu>
This patch merges the platform driver support into the main body of
xilinx_spi.c in preparation for merging the OF and non-OF support
code.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Tested-by: Michal Simek <monstr@monstr.eu>
v2 changes:
from Thierry Reding:
* add "select TEGRA_SYSTEM_DMA" to Kconfig
from Grant Likely:
* add oneline description to header
* inline references to DRIVER_NAME
* inline references to BUSY_TIMEOUT
* open coded bytes_per_word()
* spi_readl/writel -> spi_tegra_readl/writel
* move transfer validation to spi_tegra_transfer
* don't request_mem_region iomem as platform bus does that for us
* __exit -> __devexit
v3 changes:
from Russell King:
* put request_mem_region back int
from Grant Likely:
* remove #undef DEBUG
* add SLINK_ to register bit defines
* remove unused bytes_per_word
* make spi_tegra_readl/writel static linine
* various refactoring for clarity
* mark err if BSY bit is not cleared after 1000 retries
* move spinlock to protect setting of RDY bit
* subsys_initcall -> module_init
v3 changes:
from Grant Likely:
* update spi_tegra to use PTR_ERRless dma API
v4 changes:
from Grant Likely:
* remove empty spi_tegra_cleanup fucntion
* allow device ids of -1
Signed-off-by: Erik Gilling <konkers@android.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Cc: Thierry Reding <thierry.reding@avionic-design.de>
Cc: Russell King <linux@arm.linux.org.uk>
spi: tegra: cleanups from upstream review
Change-Id: Icecf7e64efcb39de072a15234ba1faa4bad40d25
Signed-off-by: Erik Gilling <konkers@android.com>
Add eSPI controller support based on the library code spi_fsl_lib.c.
The eSPI controller is newer controller 85xx/Pxxx devices supported.
There're some differences comparing to the SPI controller:
1. Has different register map and different bit definition
So leave the code operated the register to the driver code, not
the common code.
2. Support 4 dedicated chip selects
The software can't controll the chip selects directly, The SPCOM[CS]
field is used to select which chip selects is used, and the
SPCOM[TRANLEN] field is set to tell the controller how long the CS
signal need to be asserted. So the driver doesn't need the chipselect
related function when transfering data, just set corresponding register
fields to controll the chipseclect.
3. Different Transmit/Receive FIFO access register behavior
For SPI controller, the Tx/Rx FIFO access register can hold only
one character regardless of the character length, but for eSPI
controller, the register can hold 4 or 2 characters according to
the character lengths. Access the Tx/Rx FIFO access register of the
eSPI controller will shift out/in 4/2 characters one time. For SPI
subsystem, the command and data are put into different transfers, so
we need to combine all the transfers to one transfer in order to pass
the transfer to eSPI controller.
4. The max transaction length limitation
The max transaction length one time is limitted by the SPCOM[TRANSLEN]
field which is 0xFFFF. When used mkfs.ext2 command to create ext2
filesystem on the flash, the read length will exceed the max value of
the SPCOM[TRANSLEN] field.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Refactor the common code in file spi_fsl_spi.c to spi_fsl_lib.c used
by SPI/eSPI controller driver as a library, and leave the QE/CPM SPI
controller code in the SPI controller driver spi_fsl_spi.c.
Because the register map of the SPI controller and eSPI controller
is so different, also leave the code operated the register to the
driver code, not the common code.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This will pave the way to refactor out the common code which can be used
by the eSPI controller driver, and rename the SPI controller dirver to the
file spi_fsl_spi.c.
Signed-off-by: Mingkai Hu <Mingkai.hu@freescale.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Topcliff PCH is the platform controller hub that is going to be used
in Intel's upcoming general embedded platform. All IO peripherals in
Topcliff PCH are actually devices sitting on AMBA bus. This patch
adds a driver for the SPI bus integrated into the Topcliff device.
Signed-off-by: Masayuki Ohtake <masa-korg@dsn.okisemi.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds an SPI master driver for the Cirrus EP93xx SPI controller found
in EP93xx chips.
Signed-off-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add support for the QSPI controller found some on Freescale/Motorola
Coldfire MCUs.
Full duplex, active high cs, spi modes 0-3 and word sizes 8-16 bits are
supported. The hardware drives the MISO, MOSI and SCLK lines, but the chip
selects are managed via GPIO and must be configured by the board code.
The QSPI controller has an 80 byte buffer which allows us to transfer up to 16
words at a time. For transfers longer than 16 words, we split the buffer in
half so we can update in one half while the controller is operating on the
other half. Interrupt latencies then ultimately limits our sustained thru-put
to something less than half the maximum speed supported by the part.
Signed-off-by: Steven King <sfking@fdwdc.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds support for a SPI master driver for the
DaVinci series of SOCs
Signed-off-by: Sandeep Paulraj <s-paulraj@ti.com>
Signed-off-by: Mark A. Greer <mgreer@mvista.com>
Signed-off-by: Philby John <pjohn@in.mvista.com>
Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Each SPI controller has exactly one CS line and as such doesn't
provide for multi-cs. We implement a workaround to support
multi-cs by _not_ configuring the mux'ed CS pin for each SPI
controller. The CS mechanism is assumed to be fully machine
specific - the driver doesn't even assume some GPIO pin is used
to control the CS.
The driver selects between DMA and POLLING mode depending upon
the xfer size - DMA mode for xfers bigger than FIFO size, POLLING
mode otherwise.
The driver has been designed to be capable of running SoCs since
s3c64xx and till date, for that reason some of the register fields
have been passed via, SoC specific, platform data.
Signed-off-by: Jassi Brar <jassi.brar@samsung.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Add pseudo-DMA by FIQ to the S3C24XX SPI driver. This allows the driver
to get DMA-like performance where there are either no free DMA channels or
when doing transfers that required both TX and RX data paths.
Since this patch requires the addition of an assembly file to hold the FIQ
code, we rename the module (instead of adding a rename of the .c file to
this patch). We expect most users are loading this via udev and thus
there should be no change to the userland configuration.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Driver for the Designware SPI core, it supports multipul interfaces like
PCI/APB etc. User can use "dw_apb_ssi_db.pdf" from Synopsys as HW
datasheet.
[randy.dunlap@oracle.com: fix build]
[akpm@linux-foundation.org: build fix]
Signed-off-by: Feng Tang <feng.tang@intel.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This change adds the OMAP SPI 100k driver created by
Fabrice Crohas <fcrohas@gmail.com>. This SPI bus is found on
OMAP7xx-series smartphones, and for many, the touchscreen is
attached to this bus.
The lion's share of the work was done by Fabrice on this driver --
I am merely porting it from the Linwizard project on his behalf.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch is V2 of SPI Master support for the SuperH MSIOF.
Full duplex, spi mode 0-3, active high cs, 3-wire and lsb
first should all be supported, but the driver has so far
only been tested with "mmc_spi".
The MSIOF hardware comes with 32-bit FIFOs for receive and
transmit, and this driver simply breaks the SPI messages
into FIFO-sized chunks. The MSIOF hardware manages the pins
for clock, receive and transmit (sck/miso/mosi), but the chip
select pin is managed by software and must be configured as
a regular GPIO pin by the board code.
Performance wise there is still room for improvement, but
on a Ecovec board with the built-in sh7724 MSIOF0 this driver
gets Mini-sd read speeds of about half a megabyte per second.
Future work include better clock setup and merging of 8-bit
transfers into 32-bit words to reduce interrupt load and
improve throughput.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch adds in a platform device driver using the xilinx_spi common module.
Tested-by: John Linn <John.Linn@xilinx.com>
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This patch splits the xilinx_spi driver into a generic part and a
OF driver part.
The reason for this is to later add in a platform driver as well.
Tested-by: John Linn <John.Linn@xilinx.com>
Signed-off-by: Richard Röjfors <richard.rojfors@mocean-labs.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
This makes the filename match the Kconfig symbol and the driver name.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver has been tested on i.MX1/i.MX27/i.MX35 with an AT25 type
EEPROM and on i.MX27/i.MX31 with a Freescale MC13783 PMIC.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Tested-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: David Brownell <david-b@pacbell.net>
Cc: Andrea Paterniani <a.paterniani@swapp-eng.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a SPI driver for the SPI controller found in the IBM/AMCC
4xx PowerPC's.
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Wolfgang Ocker <weo@reccoware.de>
Acked-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
Signed-off-by: Steven A. Falco <sfalco@harris.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This driver is in a non working state at the moment and will be replaced
by a bitbang driver which can also handle the newer i.MX variants
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: David Brownell <david-b@pacbell.net>
Acked-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Since we renamed the file, we might want to rename the file internals too.
Though we don't bother with changing platform driver name and platform
module alias. The stuff is legacy and hopefully we'll remove it soon.
Suggested-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The driver handles MPC83xx, MPC85xx and MPC86xx SPI controllers, so rename
the file for clarity.
Suggested-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a driver for the ARM PL022 PrimeCell SSP/SPI
driver found in the U300 platforms as well as in some
ARM reference hardware, and in a modified version on the
Nomadik board.
Reviewed-by: Alessandro Rubini <rubini-list@gnudd.com>
Reviewed-by: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Generalize the old at91rm9200 "bootstrap" bitbanging SPI master driver as
"spi_gpio", so it works with arbitrary GPIOs and can be configured through
platform_data. Such SPI masters support:
- any number of bus instances (bus_num is the platform_device.id)
- any number of chipselects (one GPIO per spi_device)
- all four SPI_MODE values, and SPI_CS_HIGH
- i/o word sizes from 1 to 32 bits;
- devices configured as with any other spi_master controller
When configured using platform_data, this provides relatively low clock
rates. On platforms that support inlined GPIO calls, significantly
improved transfer speeds are also possible with a semi-custom driver.
(It's still painful when accessing flash memory, but less so.)
Sanity checked by using this version to replace both native controllers on
a board with six different SPI slaves, relying on three different
SPI_MODE_* values and both SPI_CS_HIGH settings for correct operation.
[akpm@linux-foundation.org: cleanups]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Magnus Damm <damm@igel.co.jp>
Tested-by: Magnus Damm <damm@igel.co.jp>
Cc: Torgil Svensson <torgil.svensson@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds an SPI driver for the SPI controller found in various Marvell
Orion ARM SoCs. It currently supports only one slave, which must use SPI
mode 0.
[dbrownell@users.sourceforge.net: cleanups, meet specs, pass "sparse"]
Signed-off-by: Shadi Ammouri <shadi@marvell.com>
Signed-off-by: Saeed Bishara <saeed@marvell.com>
Signed-off-by: Lennert Buytenhek <buytenh@marvell.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for SPI over SCI pins. SCI is a very simple serial controller
block that can be found on older SuperH processors. In theory it is
possible to use the SCI hardware block in syncronous mode, but this version
of the driver simply hooks up the bit banging code on the SCI pins.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is a driver for SPI controller built into TXx9 MIPS SoCs.
This driver is derived from arch/mips/tx4938/toshiba_rbtx4938/spi_txx9.c.
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add OMAP24XX McSPI (Multichannel SPI) controller driver. This driver is
tested very well under OMAP GIT tree with N800 - Nokia Internet Tablet, and
some other OMAP2 boards.
Recent updates included bugfixes, cleanups, speedups, and better
conformance to the current SPI programming interface. This doesn't yet
understand the third controller instance on the OMAP 2430.
[david-b@pacbell.net: more minor cleanups to the omap2_mcspi driver]
Signed-off-by: Juha Yrjölä <juha.yrjola@solidboot.com>
Signed-off-by: Trilok Soni <soni.trilok@gmail.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Simple SPI master driver for Xilinx SPI controller.
No support for multiple masters.
Not using level 1 drivers from EDK.
[akpm@linux-foundation.org: uninlining]
Signed-off-by: Yuri Frolov <yfrolov@ru.mvista.com>
Signed-off-by: Andrei Konovalov <akonovalov@ru.mvista.com>
Cc: Kumar Gala <galak@gate.crashing.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add support for the Infineon TLE62x0 series of low-side driver chips, such
as the TLE6220 or TLE6230. These can be viewed as output GPIOs specialized
for power switching applications. The driver provides a userspace
interface to those GPIOs, and to the switch status they provide.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a driver for the LM70-LLP parport adapter, which is an eval board
for the LM70 temperature sensor. For those without that board, it may be a
simpler example of a parport-to-SPI adapter then spi_butterfly.
Signed-off-by: Kaiwan N Billimoria <kaiwan@designergraphix.com>
Doc, coding style, and interface updates; build fixes. Minor rename.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
SPI master driver for MPC52xx using its Programmable Serial Controller.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Dragos Carp <dragos.carp@toptica.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Here is a driver for the Alchemy au1550 PSC (Programmable Serial
Controller) in SPI master mode.
It supports dma transfers using the Alchemy descriptor based dma controller
for 4-8 bits per word SPI transfers. For 9-24 bits per word transfers, pio
irq based mode is used to avoid setup of dma channels from scratch on each
number of bits per word change.
Tested with au1550; this may also work on other MIPS Alchemy cpus, like
au1200/au1210/au1250. Used extensively with SD card connected via SPI;
this handles 8.1MHz SPI clock transfers using dma without any problem (the
highest SPI clock freq possible with au1550 running on 324MHz).
The driver supports sharing of SPI bus by multiple devices. All features
of Alchemy SPI mode are supported (all SPI modes, msb/lsb first, bits per
word in 4-24 range).
As the SPI clock of the controller depends on main input clock that shall
be configured externally, platform data structure for au1550 SPI controller
driver contains mainclk_hz attribute to define the input clock rate. From
this value, dividers of the controller for SPI clock are set up for
required frequency.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Whitespace and section fixups. Remove partial workaround for platform
setup bug in dma_mask setup; it couldn't work with multiple controllers.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add a filesystem API for <linux/spi/spi.h> stack. The initial version of
this interface is purely synchronous.
dbrownell@users.sourceforge.net:
Cleaned up, bugfixed; much simplified; added preliminary documentation.
Works with mdev given CONFIG_SYSFS_DEPRECATED; and presumably udev.
Updated SPI_IOC_MESSAGE ioctl to full spi_message semantics, supporting
groups of one or more transfers (each of which may be full duplex if
desired).
This is marked as EXPERIMENTAL with an explicit disclaimer that the API
(notably the ioctls) is subject to change.
Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch implements the driver necessary use the Analog Devices Blackfin
processor's SPI Port.
Signed-off-by: Bryan Wu <bryan.wu@analog.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Driver for the Atmel on-chip SPI master controller.
Tested primarily on AVR32/AT32AP7000/ATSTK1000 using mtd_dataflash and the
jffs2 filesystem. Should also work fine on various AT91 ARM-based chips
like AT91SAM926x and AT91RM9200.
Hardware documentation can be found in the AT32AP7000 data sheet, or its
AT91 siblings, which can be downloaded from
http://www.atmel.com/dyn/products/datasheets.asp?family_id=682
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This is adds a simple SPI EEPROM driver, providing access to the EEPROM
through sysfs much like the I2C "eeprom" driver ... except this driver
supports write access, and multiple EEPROM sizes.
From: "Tuppa, Walter" <walter.tuppa@siemens.com>
Since I have EEPROMs on SPI with different address sizing, I made some
changes to your at25.c to support them. Works perfectly. (Also includes a
small bugfix for the "what size address" test.)
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Walter Tuppa <walter.tuppa@siemens.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Add the SPI controller driver for Freescale i.MX(S/L/1).
Main features summary:
> Per chip setup via board specific code and/or protocol driver.
> Per transfer setup.
> PIO transfers.
> DMA transfers.
> Managing of NULL tx / rx buffer for rd only / wr only transfers.
This patch replace patch-2.6.20-rc4-spi_imx with the following changes:
> Few cosmetic changes.
> Function map_dma_buffers now return 0 for success and -1 for failure.
> Solved a bug inside spi_imx_probe function (wrong error path).
> Solved a bug inside setup function (bad undo setup for max_speed_hz).
> For read-only transfers, always write zero bytes.
This is almost the same as the 'BIS' version sent by Andrea, except for
updating the 'DUMMY' byte so that read-only transfers shift out zeroes.
That part of the API changed recently, since some half duplex peripheral
chips require that semantic.
Signed-off-by: Andrea Paterniani <a.paterniani@swapp-eng.it>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This adds a SPI driver for the Microwire controller on OMAP1 chips. This
driver has been used in the Linux-OMAP tree for some time now, including
with some of those displays using standardized 9-bit commands followed by
data with 8-bit words.
Microwire only supports half duplex transfers, but that's all that most SPI
protocols need. When full duplex, or higher speeds, are needed there are
several other controllers that can be used on OMAP.
[akpm@osdl.org: cleanups]
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Imre Deak <imre.deak@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Hardware based SPI driver for Samsung S3C24XX SoC systems
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: David Brownell <david-b@pacbell.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SPI driver for SPI by GPIO on the Samsung S3C24XX series of SoC processors.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Cc: Greg KH <greg@kroah.com>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This driver supports the SPI controller on the MPC83xx SoC devices from
Freescale. Note, this driver supports only the simple shift register SPI
controller and not the descriptor based CPM or QUICCEngine SPI controller.
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This driver turns a PXA2xx synchronous serial port (SSP) into a SPI master
controller (see Documentation/spi/spi_summary). The driver has the following
features:
- Support for any PXA2xx SSP
- SSP PIO and SSP DMA data transfers.
- External and Internal (SSPFRM) chip selects.
- Per slave device (chip) configuration.
- Full suspend, freeze, resume support.
Signed-off-by: Stephen Street <stephen@streetfiresound.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Cc: David Brownell <david-b@pacbell.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This collects some small SPI patches that seem to be missing from the MM tree:
- spi_butterfly kbuild hooks got dropped somehow; this restores them
- quick fix for a (theoretical?) m25p80_write() oops noted by Andrew
- quick fix for a potential config-specific oops for mtd_dataflash()
- minor doc tweaks
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds a bitbanging spi master, hooking up to board/adapter-specific glue
code which knows how to set and read the signals (gpios etc).
This code kicks in after the glue code creates a platform_device with the
right platform_data. That data includes I/O loops, which will usually
come from expanding an inline function (provided in the header). One goal
is that the I/O loops should be easily optimized down to a few GPIO register
accesses, in common cases, for speed and minimized overhead.
This understands all the currently defined protocol tweaking options in the
SPI framework, and might eventually serve as as reference implementation.
- different word sizes (1..32 bits)
- differing clock rates
- SPI modes differing by CPOL (affecting chip select and I/O loops)
- SPI modes differing by CPHA (affecting I/O loops)
- delays (usecs) after transfers
- temporarily deselecting chips in mid-transfer
A lot of hardware could work with this framework, though common types of
controller can't reach peak performance without switching to a driver
structure that supports pipelining of transfers (e.g. DMA queues) and maybe
controllers (e.g. IRQ driven).
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This is the core of a small SPI framework, implementing the model of a
queue of messages which complete asynchronously (with thin synchronous
wrappers on top).
- It's still less than 2KB of ".text" (ARM). If there's got to be a
mid-layer for something so simple, that's the right size budget. :)
- The guts use board-specific SPI device tables to build the driver
model tree. (Hardware probing is rarely an option.)
- This version of Kconfig includes no drivers. At this writing there
are two known master controller drivers (PXA/SSP, OMAP MicroWire)
and three protocol drivers (CS8415a, ADS7846, DataFlash) with LKML
mentions of other drivers in development.
- No userspace API. There are several implementations to compare.
Implement them like any other driver, and bind them with sysfs.
The changes from last version posted to LKML (on 11-Nov-2005) are minor,
and include:
- One bugfix (removes a FIXME), with the visible effect of making device
names be "spiB.C" where B is the bus number and C is the chipselect.
- The "caller provides DMA mappings" mechanism now has kerneldoc, for
DMA drivers that want to be fancy.
- Hey, the framework init can be subsys_init. Even though board init
logic fires earlier, at arch_init ... since the framework init is
for driver support, and the board init support uses static init.
- Various additional spec/doc clarifications based on discussions
with other folk. It adds a brief "thank you" at the end, for folk
who've helped nudge this framework into existence.
As I've said before, I think that "protocol tweaking" is the main support
that this driver framework will need to evolve.
From: Mark Underwood <basicmark@yahoo.com>
Update the SPI framework to remove a potential priority inversion case by
reverting to kmalloc if the pre-allocated DMA-safe buffer isn't available.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Thomas Chou