We were releasing the block devices before removing the host, so commands
could still be coming in which would cause a panic. Just remove the
host before releasing the block devices to close this race.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There was a missing call to scsi_host_put() causing us to leak a scsi
host every time this module was unloaded.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If kthread_run failed, we would fail to scan the host, and leak the
allocated async_scan_data. Since using a separate thread is just an
optimisation, do the scan synchronously if we fail to spawn a thread.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The current code prints:
scsi 13:0:4:0: scsi: Device offlined - not ready after error recovery
which is repetitively redundant. This patch changes that message to:
scsi 6:0:6:0: Device offlined - not ready after error recovery
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
sg uses a scheme to reallocate a single contiguous array of all its
pointers for lookup and management. This didn't matter too much when sg
could only attach 256 nodes, but now the maximum has been bumped up to
32k we're starting to push the limits of the maximum allocatable
contiguous memory. The solution to this is to eliminate the static
array and do everything via idr, which this patch does.
Acked-by: Douglas Gilbert <dougg@torque.net>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
The OnStream SCSI Tape driver uses a semaphore as mutex. Use the mutex API
instead of the (binary) semaphore.
Signed-off-by: Matthias Kaehlcke <matthias.kaehlcke@gmail.com>
Reviewed-by: Satyam Sharma <satyam@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Willem Riede <wrlk@riede.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
* Remove IRQF_DISABLED, it is clearly wrong for this driver.
* Remove wasteful spin_lock_irqsave() in interrupt handler.
The lighter-weight spin_lock() is all that's needed.
* Annotate with FIXME where arcmsr_interrupt() is called
without any spinlock being acquired.
* Eliminate pointless cast from void pointer in arcmsr_do_interrupt()
[jejb: conflict resolution]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Remove _interruptible, since receiving a signal while waiting on a
hardware condition will simply cause the driver to busy-wait.
Using msleep_interruptible() is rarely the right thing to do, when
waiting on a hardware condition to change.
Also, replace msleep with ssleep while doing this, where appropriate.
[jejb: fix up merge conflict]
Signed-off-by: Jeff Garzik <jeff@garzik.org>
Acked-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Do not adjust the iIDMA speed on ports which have a faster
link-speed than the HBA itself.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Since MSI-X vectors do not require a clearing "handshake" from
the system perspective, and the registered handler will not be
called more than once for one occurrence of receipt of a vector,
there is no requirement to flush the risc register write clearing
the interrupt condition in the risc. Also, since the msi-x
registered handlers are optimised for a particular vector, it is
preferable to handle the one vector received per invocation of
the handler.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Make several needlessly global functions static:
- qla2x00_mark_vp_devices_dead()
- qla24xx_configure_vp()
Remove unused function qla24xx_modify_vport().
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Drop usage of legacy to_qla_host() macro.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This change reduces by as much as 16% the memory footprint for
each allocated sbr_t structure requested from the mempool.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Original code, incorrectly passed the address-of a pointer rather
than the pointer value itself.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Also remove legacy '/proc' name during OS_DEVICE_NAME
registration.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Where the DPC logic would get jammed into continuously
reloging-into a port.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
There's no need to reset the RISC prior to pausing.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Newer ISPs support a mechanism to read and write flash-memory via
the firmware LOAD/DUMP memory mailbox command routines. When
supported, utilizing these mechanisms significantly reduces
overall access times.
Signed-off-by: Andrew Vasquez <andrew.vasquez@qlogic.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
One of the intents of the block prep function was to allow ULDs to use
it for preprocessing. The original SCSI model was to have a single prep
function and add a pointer indirect filter to build the necessary
commands. This patch reverses that, does away with the init_command
field of the scsi_driver structure and makes ULDs attach directly to the
prep function instead. The value is really that it allows us to begin
to separate the ULDs from the SCSI mid layer (as long as they don't use
any core functions---which is hard at the moment---a ULD doesn't even
need SCSI to bind).
Acked-by: Jens Axboe <jens.axboe@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
If you build a multiplatform kernel for iSeries and pSeries, with
ibmvscsic support, the resulting client doesn't work on iSeries.
This fixes that, using the appropriate low-level operations
for the machine detected at runtime.
[jejb: fixed up rejections around the srp transport patch]
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
So its ancient, its crap, but it kept showing up in my scans for stuff
that wanted fixing...
- Redo the proc code to be far cleaner
- Clean various return (0) type constructs
- Use cpu_relax()
The various waits ought to time out but thats another issue and probably
not worth solving.
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
In scsi module I've found some inconsistency between variable type
used in module_param_named and type passed to module_param_named as an
argument. Especially the inconsistency of `max_scsi_luns' parameter is
a bit serious because the description text says "last scsi LUN (should
be between 1 and 2^32-1)".
Signed-off-by: Masatake YAMATO <jet@gyve.org>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Convert ide-scsi to the new data accessors and cleanup
the !use_sg code paths.
In old code the driver was trying to translate narrow commands,
if received, to wide commands. This code path still assumed
scsi_cmnd->request_buffer is a linear char pointer.
This means that this driver was broken since 2.6.17.
As suggested by Christoph Hellwig I set
use_10_for_rw = 1; and use_10_for_ms = 1;
for this device and completely killed the translation.
Signed-off-by: Boaz Harrosh <bharrosh@panasas.com>
Acked-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
A BUSY status returned on a write request results in a stale residual
being returned when the write ultimately successfully completes.
This can be reproduced as follows:
1) issue immediate mode rewind to scsi tape drive
2) issue write request
The tape drive returns busy. The low level driver detects underrun and
sets the residual into the scsi command. The low level driver responds
with (DID_OK << 16) | scsi_status. scsi_status is 8, hence
status_byte(result) == 4, i.e., BUSY.
scsi_softirq_done() calls scsi_decide_disposition() which returns
ADD_TO_MLQUEUE. scsi_softirq_done() then calls scsi_queue_insert()
which, on the way to resubmitting the request to the driver, calls
scsi_init_cmd_errh().
The attached patch modifies scsi_init_cmd_errh() to clear the resid
field. This prevents a "stale" residual from being returned when the
scsi command finally completes without a BUSY status.
Signed-off-by: Michael Reed <mdr@sgi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Mailing list changed. The former list at mpt_linux_developer@lsi.com is no
longer in service. Please use the new email provided listed in this patch.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Adding 949X, 949E, and 1078 to Kconfig. Adding "depends on FUSION"
required in the FUSION_LOGGING section, and fixing a spelling error.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Some other vender has concerns over this copyright, and Dell has
approved removing it.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Cleaning up code by accesing the ioc pointer directly instead of via hd->ioc. In the future, most data members of struct MPT_SCSI_HOST will be either deleted or moved to struct MPT_ADAPTER.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
common naming of vdevice through out driver
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
cleaning up some white space that was introduce in a recent "cb_idx int to u8" patch.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Standardize all prints using common MYIOC_s_XXX_FMT macro defined in mptbase.h. Currently the driver uses several different methods to display info, where in some cases the "controller name" generating the printk is not provided.
Signed-off-by: Eric Moore <Eric.Moore@lsi.com>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
CC [M] drivers/scsi/arcmsr/arcmsr_hba.o
drivers/scsi/arcmsr/arcmsr_attr.c:186: warning: initialization from
incompatible pointer type
drivers/scsi/arcmsr/arcmsr_attr.c:196: warning: initialization from
incompatible pointer type
drivers/scsi/arcmsr/arcmsr_attr.c:206: warning: initialization from
incompatible pointer type
drivers/scsi/arcmsr/arcmsr_hba.c: In function 'arcmsr_alloc_ccb_pool':
drivers/scsi/arcmsr/arcmsr_hba.c:329: warning: assignment from
incompatible pointer type
drivers/scsi/arcmsr/arcmsr_hba.c: At top level:
drivers/scsi/arcmsr/arcmsr_hba.c:101: warning:
'arcmsr_pci_error_detected' declared 'static' but never defined
drivers/scsi/arcmsr/arcmsr_hba.c:102: warning: 'arcmsr_pci_slot_reset'
declared 'static' but never defined
The majority being incorrect casting or the fact that binary attributes
now take an additional argument.
Cc: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Description:
** support ARC1200/1201/1202 SATA RAID adapter, which is named
ACB_ADAPTER_TYPE_B
** modify the arcmsr_pci_slot_reset function
** modify the arcmsr_pci_ers_disconnect_forepart function
** modify the arcmsr_pci_ers_need_reset_forepart function
Signed-off-by: Nick Cheng <nick.cheng@areca.com.tw>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
This removes the unused sysfs attribute overwriting logic for most of
the attributes, and plugs them into the driver core default attribute
creation.
Without this patch, at the time of the events for the SCSI LUN's, there
will be no sysfs files, because their creation is delayed until the sd
driver has spun up the disks, which might take several seconds. It is the
last WAIT_FOR_SYSFS rule in the default udev setup which can be removed
with this change.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Follow the example of some other drivers by defining DRV_NAME to be
"advansys". Prevents spelling mistakes.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Delete comments relating to the previous structure of the driver.
I have no intention of honouring them ;-)
- Reformat comments > 80 columns
- Remove now-obsolete comments from advansys_interrupt
- Change adv_get_sglist() from do {} while (1) to for (;;)
- Return void from AscInitQLinkVar()
- Take out a level of indentation in adv_get_sglist()
- Reduce indentation level of AscAsyncFix()
- Remove unused macros
- Refactor AscSendScsiQueue slightly
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
- Replace ASC_ASSERT() with BUG_ON().
In a few places, get rid of the assertion altogether -- the ensuing
crash will tell us all we need to know. Use BUG() where it fits better
than BUG_ON(). Also fix a fencepost error in advansys_proc_info().
- Replace DvcSleepMilliSecond with mdelay.
Despite its name using 'sleep', the implementation was a delay.
I've marked some places with XXX where we should probably be using
msleep instead. They need to be audited to be sure we can sleep in
that context.
- Replace DvcDelayMicroSecond with udelay.
- Replace DvcDelayNanoSecond with udelay too.
All callers were multiples of 1000.
- Remove DvcEnterCritical and DvcLeaveCritical.
These functions are no-ops, and as the comments said, the spinlock
protects the critical sections.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
AscExeScsiQueue() has one caller, and it passes the address of a
variable; this cannot ever be NULL. This is the only place that ever
sets ASCQ_ERR_SCSIQ_NULL_PTR, so delete that error code too, as well as
several other unused ASCQ_ERR codes.
Signed-off-by: Matthew Wilcox <matthew@wil.cx>
Signed-off-by: James Bottomley <James.Bottomley@SteelEye.com>
Matthew Wilcox