Rockchip platform merely enable usb3 clocks and
populate its children. So we can use this generic
glue layer to support Rockchip dwc3.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit,
which specifies whether disable delay PHY power change
from P0 to P1/P2/P3 when link state changing from U0
to U1/U2/U3 respectively.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Support to configure the UTMI+ PHY with an 8- or 16-bit
interface via DT. The UTMI+ PHY interface is a hardware
capability, and it's platform dependent. Normally, the
PHYIF can be configured during coreconsultant.
But for some specific USB cores(e.g. rk3399 SoC DWC3),
the default PHYIF configuration value is false, so we
need to reconfigure it by software.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit,
which specifies whether the USB2.0 PHY provides a free-running
PHY clock, which is active when the clock control input is active.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With composite gadget (ACM + NCM), USB3380 to host TCP transfer
speed dropped to 150 Mbit/s compared to 900 Mbit/s with NCM
gadget. Problem seems to be that net2280/USB3380 has only four
DMA channels and those DMA channels are allocated to first HW
endpoints. Endpoint match function was mapping endpoint names
directly, so NCM did not get DMA for bulk endpoints.
This patch changed match_ep to prefer DMA enabled hw endpoints
for bulk usb endpoints and PIO for interrupt usb endpoints.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
With SuperSpeed CDC NCM gadget, net2280 would get stuck in
'handle_ep_small' function. Triggering issue requires large
TCP transfer from host to USB3380.
Patch adds check for stuck condition and prevents hard lockup.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Patch enables SuperSpeed for NCM gadget.
Tested with USB3380 and measured TCP throughput with two Intel PCs:
udc to host: 920 Mbit/s
host to udc: 550 Mbit/s
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
alloc_ordered_workqueue replaces the deprecated
create_singlethread_workqueue.
There are multiple work items on the work queue, which require
ordering. Hence, an ordered workqueue has been used.
The workqueue "wq_otg" is not being used on a memory reclaim path.
Hence, WQ_MEM_RECLAIM has not been set.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The assignment ret = ret is redundant and can be removed.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Disabling USB gadget functions configured through configfs is something
that can happen in normal use cases. Keep the existing log for this type
of event, but only as information, not as an error.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As the last known user, ie. pxa27x_udc relying on calls to
usb_gadget_xxx() was amended to use the phy notifier, remove a bit the
USB stack adherence.
Actually the driver still uses the gadget API for structures definition,
but the implementation of USB gadget specific function usb_gadget_*() is
not necessary anymore.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the gpio based case, the status of the phy is known at start by
reading the VBus gpio.
Actually, this is a fix, as this initial state, when not set up,
prevents a gadget to answer to the enumeration phase, as there is no
notification in this case (the VBus is already high when kernel boots)
so no interrupt is triggered, and the flow is :
- gadget initializes
- gadget gets its phy-generic with a xxx_get_phy_xxx() call type
- gadget does a "set_peripheral()" call type
=> here if the otg->state is correctly filled, the proper vbus
handling will be called, and the gadget will be aware it should
answer enumeration and go forth
Without this fix, the USB cable must be removed and replugged for any
gadget relying on phy-generic and its gpio vbus handling to work.
The problem was seen on a pxa27x architecture based board on a
devicetree build.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In the legacy behavior, and USB phy, upon detection a VBus signal, was
calling usb_gadget_vbus_(dis)connect().
This model doesn't work if the phy is generic and doesn't have an
adherence to the gadget API.
Instead of relying on the phy to call the gadget API, hook up the phy
notifier to report the VBus event, and upon it call the usb gadget API
ourselves.
This brings a new ordering problem, as before even if the usb_get_phy()
was failing because the UDC was probed before the phy, the phy would
call the gadget anyway, making the VBus connection event forwarded to
the gadget. Now we rely on the notifier, we have to ensure the
xxx_get_phy() does indeed work.
In order to cope with this, it is assumed that :
- for legacy platform_data machine, as the ordering cannot be ensured,
the phy must call usb_gadget_vbus_(dis)connect, such as
phy-gpio-vbus-usb.c
- for new devicetree platforms, we'll rely on the probe deferral, and
the phy can be gadget API agnostic.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Upon transfer completion after a full ring, let's
add more TRBs to our ring in order to complete our
request successfully.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There was a typo when generating endpoint name which
would be very confusing when debugging. Fix it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
These product IDs are listed in Windows driver.
0x6803 corresponds to WeTelecom WM-D300.
0x6802 name is unknown.
Signed-off-by: Aleksandr Makarov <aleksandr.o.makarov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
UBSAN complains about a left shift by -1 in proc_do_submiturb(). This
can occur when an URB is submitted for a bulk or control endpoint on
a high-speed device, since the code doesn't bother to check the
endpoint type; normally only interrupt or isochronous endpoints have
a nonzero bInterval value.
Aside from the fact that the operation is illegal, it shouldn't matter
because the result isn't used. Still, in theory it could cause a
hardware exception or other problem, so we should work around it.
This patch avoids doing the left shift unless the shift amount is >= 0.
The same piece of code has another problem. When checking the device
speed (the exponential encoding for interrupt endpoints is used only
by high-speed or faster devices), we need to look for speed >=
USB_SPEED_SUPER as well as speed == USB_SPEED HIGH. The patch adds
this check.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Vittorio Zecca <zeccav@gmail.com>
Tested-by: Vittorio Zecca <zeccav@gmail.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The maximum value allowed for wMaxPacketSize of a high-speed interrupt
endpoint is 1024 bytes, not 1023.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: aed9d65ac3 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove variables affected but never read.
Also drop the now unused TI_SET_SERIAL_FLAGS define.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
[ johan: drop TI_SET_SERIAL_FLAGS ]
Signed-off-by: Johan Hovold <johan@kernel.org>
Use C_X tty.h macros to avoid direct manipulation of termios
c_cflag variable.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
It is useless to check the return of usb_get_serial_port_data in the tty
and tty-port callbacks.
No need to check interface private data in close() either.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
__uX types should only be used for user-space interactions.
Also clean up uart-config endianess handling, and drop some redundant
casts.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
If the ring is full and we are processing a big
sglist, then let's interrupt so we can, later, add
more TRBs to the ring.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
These two fields will be used in a follow-up patch
to track how many entries of request's sglist we
have already processed. The reason is that if a
gadget driver sends an sglist with more entries then
we can fit in the ring, we will have to continue
processing remaining afterwards.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We know that we have to iterate over the list of
started requests. Instead of looping forever, we can
rely on list_for_each_entry(). Likewise, instead of
a do {} while loop over all, maybe available,
scatterlist entries, we can detect if $this request
uses scatterlist and rely on for_each_sg().
This makes the code easier to follow while making
sure that we will *always* break out of the loop.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Many of the comments in that function are really
outdated and don't match what the driver is
doing. Moreover, recent patches combined programming
model for all non-control endpoints, this gives us
an opportunity to get rid of our special cases in
__dwc3_gadget_ep_queue().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We always need to decrement our index by at least
one. Simplify the implementation by using a
temporary local variable and making sure that we
will always decrement one extra if tmp == 0.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Instead of waiting until giveback before
incrementing the dequeue pointer, we can increment
it from dwc3_cleanup_done_reqs(), that way we avoid
an extra loop over all TRBs during giveback.
While at that, also avoid using req->first_trb_index
as that's completely unnecessary. A follow-up patch
will clean up further uses of that and remove the
field altogether.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The only endpoint which actually requires LST bit
and XferComplete is ep0/1. Let's save some time by
completely removing LST bit support and
XferComplete.
This simplifies and consolidates endpoint handling
for all other 3 transfer types while also avoiding
extra interrupts.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When usb gadget is set gadget serial function, it will be crash in below
situation.
It will clean the 'port->port_usb' pointer in gserial_disconnect() function
when usb link is inactive, but it will release lock for disabling the endpoints
in this function. Druing the lock release period, it maybe complete one request
to issue gs_write_complete()--->gs_start_tx() function, but the 'port->port_usb'
pointer had been set NULL, thus it will be crash in gs_start_tx() function.
This patch adds the 'port->port_usb' pointer checking in gs_start_tx() function
to avoid this situation.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
__dwc3_gadget_wakeup() is called while holding a spinlock, then depends on
jiffies in order to timeout while polling the USB core for a link state
update. In the case the wakeup failed, the timeout will never happen and
will also cause the cpu to stall until rcu_preempt kicks in.
This switches to a "decrement variable and wait" timeout scheme.
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We can't assign -EINVAL to a u16.
Fixes: 3948f0e0c9 ('usb: add Freescale QE/CPM USB peripheral controller driver')
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In eth_start_xmit, the socket buffer may be NULL. So, add NULL pointer
check at .wrap API.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In eth_start_xmit, the socket buffer may be NULL. So, add NULL pointer
check at .wrap API.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In case of error, the function usb_get_phy() returns ERR_PTR() and never
returns NULL. The NULL test in the return value check should be replaced
with IS_ERR().
Fixes: b5a2875605 ("usb: renesas_usbhs: Allow an OTG PHY driver to
provide VBUS")
Cc: <stable@vger.kernel.org> # v4.3+
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Allow for platforms that have a reset controller driver in place to bring
the USB IP out of reset.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
After going through runtime_suspend/runtime_resume
cycle once we would be left with an unbalanced
pm_runtime_get() call. Fix that by making sure that
we try to suspend right after resuming so things are
balanced and device can runtime_suspend again.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
During runtime_resume of dwc3-pci.c, we need to
runtime suspend our child device (which is dwc3
proper) otherwise nothing will happen.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
When the controller is configured to be dual role and it's in host mode,
if bind udc and gadgt driver, those gadget operations will do gadget
disconnect and finally pull down DP line, which will break host function.
Cc: <stable@vger.kernel.org> # 4.1+
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Remove the hcd after checking for the xhci last quirks, not before.
This caused a hang on a Alpine Ridge xhci based maching which remove
the whole xhci controller when unplugging the last usb device
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device
If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.
virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
[] Unable to handle kernel paging request at virtual address 00001a68
[] pgd=ffffffc001430000
[] [00001a68] *pgd=000000013c807003, *pud=000000013c807003,
*pmd=000000013c808003, *pte=0000000000000000
[] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[] CPU: 0 PID: 39 Comm: kworker/0:1 Tainted: G U
[] Workqueue: pm pm_runtime_work
[] task: ffffffc0bc0e0bc0 ti: ffffffc0bc0ec000 task.ti:
ffffffc0bc0ec000
[] PC is at xhci_stop_device.constprop.11+0xb4/0x1a4
This issue is found when running with realtek ethernet device
(0bda:8153).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Enqueue the first TRB even if full_len is zero.
Without this "adb install <apk>" freezes the system.
Signed-off-by: Alban Browaeys <alban.browaeys@gmail.com>
Fixes: 86065c2719 ("xhci: don't rely on precalculated value of needed trbs in the enqueue loop")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fix "Command completion event does not match command" errors by always
handling the command ring stopped events.
The command ring stopped event is generated as a result of aborting
or stopping the command ring with a register write. It is not caused
by a command in the command queue, and thus won't have a matching command
in the comman list.
Solve it by handling the command ring stopped event before checking for a
matching command.
In most command time out cases we abort the command ring, and get
a command ring stopped event. The events command pointer will point at
the current command ring dequeue, which in most cases matches the timed
out command in the command list, and no error messages are seen.
If we instead get a command aborted event before the command ring stopped
event, the abort event will increse the command ring dequeue pointer, and
the following command ring stopped events command pointer will point at the
next, not yet queued command. This case triggered the error message
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This fixes the "BOGUS urb xfer" warning logged by usb_submit_urb().
Signed-off-by: Gavin Li <git@thegavinli.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Currently bcma-hcd driver handles 3 different bcma cores:
1) BCMA_CORE_USB20_HOST (0x819)
2) BCMA_CORE_NS_USB20 (0x504)
3) BCMA_CORE_NS_USB30 (0x505)
The first one was introduced years ago and so far was used on MIPS
devices only. All Northstar (ARM) devices were using other two cores
which allowed easy implementation of separated initialization paths.
It seems however Broadcom decided to reuse this old USB 2.0 controller
on some recently introduced cheaper Northstar BCM53573 SoCs. I noticed
this on Tenda AC9 (based on BCM47189B0 belonging to BCM53573 family).
There is no difference in this old controller core identification
between MIPS and ARM devices: they share the same id and revision. We
need different controller initialization procedure however.
To handle this add a check for architecture and implement required
initialization for ARM case.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In case of error, the function platform_device_register_simple() returns
ERR_PTR() and never returns NULL. The NULL test in the return value
check should be replaced with IS_ERR().
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
alloc_ordered_workqueue replaces the deprecated
create_singlethread_workqueue.
The workqueue "workqueue" has multiple workitems which may require
ordering. Hence, a dedicated ordered workqueue has been used.
Since the workqueue is not being used on a memory reclaim path,
WQ_MEM_RECLAIM has not been set.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Dynamic debugging will already add the function (and the line number)
to a debug message if one requests that. It makes no sense to add
them unconditionally in a driver.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
kmalloc will print enough information in case of failure.
Signed-off-by: Wolfram Sang <wsa-dev@sang-engineering.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There is an allocation with GFP_KERNEL flag in mos7840_write(),
while it may be called from interrupt context.
Follow-up for commit 1912528376 ("USB: kobil_sct: fix non-atomic
allocation in write path")
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
There is an allocation with GFP_KERNEL flag in mos7720_write(),
while it may be called from interrupt context.
Follow-up for commit 1912528376 ("USB: kobil_sct: fix non-atomic
allocation in write path")
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Here is a fix of a memory leak in a driver-registration error path, and
some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=k37B
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-linus
Johan writes:
USB-serial fixes for v4.8-rc2
Here is a fix of a memory leak in a driver-registration error path, and
some new device ids.
Signed-off-by: Johan Hovold <johan@kernel.org>
In sg_timeout(), req->status is set to "-ETIMEDOUT" before calling
into usb_sg_cancel(). usb_sg_cancel() will do nothing and return
directly if req->status has been set to a non-zero value. This will
cause driver hang whenever transfer time out is triggered.
This patch fixes this issue. It could be backported to stable kernel
with version later than v3.15.
Cc: stable@vger.kernel.org # 3.15+
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com>
Suggested-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
First set of fixes for v4.8-rc cycle. Again, dwc3 is
the most active driver with over 60% of this pull
request touching it.
The most important fixes are related to scatterlist
usage with dwc3. Before this pull request, we were
increment request->actual multiple times and this
would result in request->actual being larger than
request->length.
Also, if a we received a short packet midway through
processing a scatterlist, we were not clearning HWO
bit as we should.
Other than the large dwc3 scatterlist fixes, we have
a new Device ID for Intel's Kabylake silicon.
Other drivers, such as fsl_qe_udc and renesas udc,
also got a few minor fixes. Details are in shortlog.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=7VYA
-----END PGP SIGNATURE-----
Merge tag 'fixes-for-v4.8-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.8-rc1
First set of fixes for v4.8-rc cycle. Again, dwc3 is
the most active driver with over 60% of this pull
request touching it.
The most important fixes are related to scatterlist
usage with dwc3. Before this pull request, we were
increment request->actual multiple times and this
would result in request->actual being larger than
request->length.
Also, if a we received a short packet midway through
processing a scatterlist, we were not clearning HWO
bit as we should.
Other than the large dwc3 scatterlist fixes, we have
a new Device ID for Intel's Kabylake silicon.
Other drivers, such as fsl_qe_udc and renesas udc,
also got a few minor fixes. Details are in shortlog.
stop consuming TRBs when we reach one with HWO bit
already set. This will prevent us from prematurely
retiring a TRB.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According to Synopsys Databook 2.60a, section 8.3.4,
it's stated that:
The LST bit should be set to 0 (isochronous
transfers normally continue until the
endpoint is removed entirely, at which time
an End Transfer command is used to stop the
transfer).
This patch makes sure that detail is observed and
fixes a regression with Android Audio playback
caused by recent changes to DWC3 gadget.
Signed-off-by: Janusz Dziedzic <januszx.dziedzic@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When rndis data transfer is in progress, some Windows7 Host PC is not
sending the GET_ENCAPSULATED_RESPONSE command for receiving the response
for the previous SEND_ENCAPSULATED_COMMAND processed.
The rndis function driver appends each response for the
SEND_ENCAPSULATED_COMMAND in a queue. As the above process got corrupted,
the Host sends a REMOTE_NDIS_RESET_MSG command to do a soft-reset.
As the rndis response queue is not freed, the previous response is sent
as a part of this REMOTE_NDIS_RESET_MSG's reset response and the Host
block any more Rndis transfers.
Hence free the rndis response queue as a part of this soft-reset so that
the correct response for REMOTE_NDIS_RESET_MSG is sent properly during the
response command.
Signed-off-by: Rajkumar Raghupathy <raghup@codeaurora.org>
Signed-off-by: Xerox Lin <xerox_lin@htc.com>
[AmitP: Cherry-picked this patch and folded other relevant
fixes from Android common kernel android-4.4]
Signed-off-by: Amit Pundir <amit.pundir@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The udc device needs to be deleted if error occurs
Fixes: 855ed04a37 ("usb: gadget: udc-core: independent registration of
gadgets and gadget drivers")
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The udc->eps[] array has USB_MAX_ENDPOINTS elements so > should be >=.
Fixes: 3948f0e0c9 ('usb: add Freescale QE/CPM USB peripheral controller driver')
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
In 'composite_os_desc_req_prepare', if one of the memory allocations fail,
0 will be returned, which means success.
We should return -ENOMEM instead.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If this memory allocation fail, we will return 0, which means success.
Return -ENOMEM instead.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When reading synchronously from a non-zero endpoint, gadgetfs will
return -EFAULT even if the read succeeds, due to a bad check of the
copy_to_iter() return value.
This fix compares the return value of copy_to_iter to the amount of
bytes that was passed, and only fails if they are not the same.
Signed-off-by: Binyamin Sharet <s.binyamin@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
For case 14 and case 21, their correct return value is the number
of bytes transferred, so it is a positive integer. But in usbtest_ioctl,
it takes non-zero as false return value for usbtest_do_ioctl, so
it will treat the correct test as wrong test, then the time on
tests will be the minus value.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 18fc4ebdc7 ("usb: misc: usbtest: Remove timeval usage")
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add missing platform_set_drvdata() in dwc3_of_simple_probe(), otherwise
calling platform_get_drvdata() in remove returns NULL.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add missing platform_set_drvdata() in omap_otg_probe(), otherwise
calling platform_get_drvdata() in remove returns NULL.
This is detected by Coccinelle semantic patch.
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
There may be a race condition if f_fs calls unregister_gadget_item in
ffs_closed() when unregister_gadget is called by UDC store at the same time.
this leads to a kernel NULL pointer dereference:
[ 310.644928] Unable to handle kernel NULL pointer dereference at virtual address 00000004
[ 310.645053] init: Service 'adbd' is being killed...
[ 310.658938] pgd = c9528000
[ 310.662515] [00000004] *pgd=19451831, *pte=00000000, *ppte=00000000
[ 310.669702] Internal error: Oops: 817 [#1] PREEMPT SMP ARM
[ 310.675211] Modules linked in:
[ 310.678294] CPU: 0 PID: 1537 Comm: ->transport Not tainted 4.1.15-03725-g793404c #2
[ 310.685958] Hardware name: Freescale i.MX6 Quad/DualLite (Device Tree)
[ 310.692493] task: c8e24200 ti: c945e000 task.ti: c945e000
[ 310.697911] PC is at usb_gadget_unregister_driver+0xb4/0xd0
[ 310.703502] LR is at __mutex_lock_slowpath+0x10c/0x16c
[ 310.708648] pc : [<c075efc0>] lr : [<c0bfb0bc>] psr: 600f0113
<snip..>
[ 311.565585] [<c075efc0>] (usb_gadget_unregister_driver) from [<c075e2b8>] (unregister_gadget_item+0x1c/0x34)
[ 311.575426] [<c075e2b8>] (unregister_gadget_item) from [<c076fcc8>] (ffs_closed+0x8c/0x9c)
[ 311.583702] [<c076fcc8>] (ffs_closed) from [<c07736b8>] (ffs_data_reset+0xc/0xa0)
[ 311.591194] [<c07736b8>] (ffs_data_reset) from [<c07738ac>] (ffs_data_closed+0x90/0xd0)
[ 311.599208] [<c07738ac>] (ffs_data_closed) from [<c07738f8>] (ffs_ep0_release+0xc/0x14)
[ 311.607224] [<c07738f8>] (ffs_ep0_release) from [<c023e030>] (__fput+0x80/0x1d0)
[ 311.614635] [<c023e030>] (__fput) from [<c014e688>] (task_work_run+0xb0/0xe8)
[ 311.621788] [<c014e688>] (task_work_run) from [<c010afdc>] (do_work_pending+0x7c/0xa4)
[ 311.629718] [<c010afdc>] (do_work_pending) from [<c010770c>] (work_pending+0xc/0x20)
for functions using functionFS, i.e. android adbd will close /dev/usb-ffs/adb/ep0
when usb IO thread fails, but switch adb from on to off also triggers write
"none" > UDC. These 2 operations both call unregister_gadget, which will lead
to the panic above.
add a mutex before calling unregister_gadget for api used in f_fs.
Signed-off-by: Winter Wang <wente.wang@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
dev->port_usb is checked for null pointer at above code, so dev->port_usb
might be null, fix it by adding null pointer check.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
cdev->config is checked for null pointer at above code, so cdev->config
might be null, fix it by adding null pointer check.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that isochronous transfer's data is possible to
be lost as a workaround. Since this driver uses a workqueue to start
the dmac, the transfer is possible to be delayed when system load is high.
Fixes: 6e4b74e469 ("usb: renesas: fix scheduling in atomic context bug")
Cc: <stable@vger.kernel.org> # v3.4+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that unexpected BRDY interruption happens
when the usb_ep_{enable,disable}() are called with different direction.
In this case, the driver will cause the following message:
renesas_usbhs e6590000.usb: irq_ready run_error 1 : -16
This issue causes the followings:
1) A pipe is enabled as transmission
2) The pipe sent a data
3) The pipe is disabled and re-enabled as reception.
4) The pipe got a queue
Since the driver doesn't clear the BRDYSTS flags after 2) above, the issue
happens. If we add such clearing the flags into the driver, the code will
become complicate. So, this patch clears the BRDYSTS flag of reception in
usbhsg_ep_enable() to avoid complicate.
Cc: <stable@vger.kernel.org> # v4.1+ (usbhs_xxxsts_clear() is needed)
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Since R-Car Gen3 SoC has the USB-DMAC, this driver should set
dparam->has_usb_dmac to 1. Otherwise, behavior of this driver and
the usb-dmac driver will be mismatch, then sometimes receiving data will
be corrupt.
Fixes: de18757e27 ("usb: renesas_usbhs: add R-Car Gen3 power control")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Intel Kabylake PCH has the same DWC3 than Intel
Sunrisepoint. Add the new ID to the supported devices.
Cc: <stable@vger.kernel.org>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If we stop earlier due to short packet, we will
not be able to giveback all TRBs.
Cc: <stable@vger.kernel.org>
Cc: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
DWC3 has one interesting peculiarity with chained
transfers. If we setup N chained transfers and we
get a short packet before processing all N TRBs,
DWC3 will (conditionally) issue a XferComplete or
XferInProgress event and retire all TRBs from the
one which got a short packet to the last without
clearing their HWO bits.
This means SW must clear HWO bit manually, which
this patch is doing.
Cc: <stable@vger.kernel.org>
Cc: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
When using SG lists, we would end up setting
request->actual to:
num_mapped_sgs * (request->length - count)
Let's fix that up by incrementing request->actual
only once.
Cc: <stable@vger.kernel.org>
Reported-by: Brian E Rogers <brian.e.rogers@intel.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Implemented queued response handling. This queue is processed every time the
WDM_READ flag is cleared.
In case of a read error, userspace may not actually read the data, since the
driver returns an error through wdm_poll. After this, the underlying device may
attempt to send us more data, but the queue is not processed. While userspace is
also blocked, because the read error is never cleared.
After this patch, we proactively process the queue on a read error. If there was
an outstanding response to handle, that will clear the error (or go through the
same logic again, if another read error occurs). If there was no outstanding
response, this will bring the queue size back to 0, unblocking a future response
from the underlying device.
Signed-off-by: Robert Foss <robert.foss@collabora.com>
Tested-by: Robert Foss <robert.foss@collabora.com>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Modification to Kconfig, vhci_hc.c, vhci.h and vhci_sysfs.c.
1. kernel config
Followings are added.
USBIP_VHCI_HC_PORTS: Number of ports per USB/IP virtual host
controller. The default is 8 - same as current VHCI_NPORTS.
USBIP_VHCI_NR_HCS: Number of USB/IP virtual host controllers. The
default is 1. This paratmeter is replaced with USBIP_VHCI_INIT_HCS and
USBIP_VHCI_MAX_HCS included in succeeding dynamic extension patch.
2. the_controller to controllers
the_controller is changed to vhci_pdevs: array of struct
platform_device.
3. vhci_sysfs.c
Sysfs structure is changed as following.
BEFORE:
/sys/devices/platform
+-- vhci
+-- status
+-- attach
+-- detach
+-- usbip_debug
AFTER: example for CONFIG_USBIP_NR_HCS=4
/sys/devices/platform
+-- vhci
| +-- nports
| +-- status
| +-- status.1
| +-- status.2
| +-- status.3
| +-- attach
| +-- detach
| +-- usbip_debug
+-- vhci.1
+-- vhci.2
+-- vhci.3
vhci[.N] is shown for each host controller kobj. vhch.1, vhci.2, ...
are shown only when CONFIG_USBIP_NR_HCS is more than 1. Only 'vhci'
(without number) has user space interfaces. 'nports' is newly added to
give ports-per-controller and number of controlles. Before that, number
of ports is acquired by reading status lines. Status is divided for
each controller to avoid page size (4KB) limitation.
Old userspace tool binaries work with the first status within the first
controller.
Inconsistency between status header and content is fixed.
4th and 5th column are
header: "dev bus"
content(unused): "000 000"
content(used): "%08x", devid
Only 1st and 2nd column are used by program. In old version, sscanf()
in parse_status expect no bus column. And bus_id string is shown in the
last column. Then bus in the header is removed and unused content is
replaced with 8 zeros. The sscanf() expects more than 5 columns and new
has 6 columns so there's no compatibility issue in this change.
Signed-off-by: Nobuo Iwata <nobuo.iwata@fujixerox.co.jp>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The helper usb_of_get_child_node is defined at of.c, but missing its
declare as a global function. Fix it by adding related header file
as well as compile it on conditional of CONFIG_OF.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: linux-kernel@lists.codethink.co.uk
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reported-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The whole Kconfig entries of the USB subsystem are surrounded with
"if USB_SUPPORT" ... "endif", so CONFIG_USB_SUPPORT=y is surely met
when these two Kconfig options are visible.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
GPIO control register is divided into IOPINS1 and IOPINS2.
And low 4-bit of register is controls output.
So, this patch fixes wrong mask of GPIO output.
Signed-off-by: Jaewon Kim <jaewon02.kim@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Hans de Goede has reported a difficulty in the Linux port of libusb.
When a device is removed, the poll() system call in usbfs starts
returning POLLERR as soon as udev->state is set to
USB_STATE_NOTATTACHED, but the outstanding URBs are not available for
reaping until some time later (after usbdev_remove() has been called).
This is awkward for libusb or other usbfs clients, although not an
insuperable problem.
At any rate, it's easy to change usbfs so that it returns POLLHUP as
soon as the state becomes USB_STATE_NOTATTACHED but it doesn't return
POLLERR until after the outstanding URBs have completed. That's what
this patch does; it uses the fact that ps->list is always on the
dev->filelist list until usbdev_remove() takes it off, which happens
after all the outstanding URBs have been cancelled.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
usbdev_mmap allocates a buffer. The size of the buffer is determined
by a user. So with this code (no need to be root):
int fd = open("/dev/bus/usb/001/001", O_RDONLY);
mmap(NULL, 0x800000, PROT_READ, MAP_SHARED, fd, 0);
we can see a warning:
WARNING: CPU: 0 PID: 21771 at ../mm/page_alloc.c:3563 __alloc_pages_slowpath+0x1036/0x16e0()
...
Call Trace:
[<ffffffff8117a3ae>] ? warn_slowpath_null+0x2e/0x40
[<ffffffff815178b6>] ? __alloc_pages_slowpath+0x1036/0x16e0
[<ffffffff81516880>] ? warn_alloc_failed+0x250/0x250
[<ffffffff8151226b>] ? get_page_from_freelist+0x75b/0x28b0
[<ffffffff815184e3>] ? __alloc_pages_nodemask+0x583/0x6b0
[<ffffffff81517f60>] ? __alloc_pages_slowpath+0x16e0/0x16e0
[<ffffffff810565d4>] ? dma_generic_alloc_coherent+0x104/0x220
[<ffffffffa0269e56>] ? hcd_buffer_alloc+0x1d6/0x3e0 [usbcore]
[<ffffffffa0269c80>] ? hcd_buffer_destroy+0xa0/0xa0 [usbcore]
[<ffffffffa0228f05>] ? usb_alloc_coherent+0x65/0x90 [usbcore]
[<ffffffffa0275c05>] ? usbdev_mmap+0x1a5/0x770 [usbcore]
...
Allocations like this one should be marked as __GFP_NOWARN. So do so.
The size could be also clipped by something like:
if (size >= (1 << (MAX_ORDER + PAGE_SHIFT - 1)))
return -ENOMEM;
But I think the overall limit of 16M (by usbfs_increase_memory_usage)
is enough, so that we only silence the warning here.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Steinar H. Gunderson <sesse@google.com>
Cc: Markus Rechberger <mrechberger@gmail.com>
Fixes: f7d34b445a (USB: Add support for usbfs zerocopy.)
Cc: 4.6+ <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
In ehci_turn_off_all_ports() all EHCI port registers are cleared to zero.
On some hardware, this can lead to an system hang,
when ehci_port_power() accesses the already cleared registers.
This patch changes the order of cleanup.
First call ehci_port_power() which respects the current bits in
port status registers
and afterwards cleanup the hard way by setting everything to zero.
Signed-off-by: Marc Ohlf <ohlf@mkt-sys.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Erroneous or malicious endpoint descriptors may have non-zero bits in
reserved positions, or out-of-bounds values. This patch helps prevent
these from causing problems by bounds-checking the wMaxPacketValue
entries in endpoint descriptors and capping the values at the maximum
allowed.
This issue was first discovered and tests were conducted by Jake Lamberson
<jake.lamberson1@gmail.com>, an intern working for Rosie Hall.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: roswest <roswest@cisco.com>
Tested-by: roswest <roswest@cisco.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Let's follow other driver registration functions and
automatically set the driver's owner member to THIS_MODULE when
ulpi_driver_register() is called. This allows ulpi driver writers
to forget about this boiler plate detail and avoids common bugs
in the process.
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's a rather simple controller, we just need to make sure USB is
powered (using GPIO pin) and reset bus core. Once this is done it's
safe to register XHCI controller and let it init PHY and do its magic.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Since commit 71723f9546 "PM / runtime: print error when activating a
child to unactive parent" I see the following error message:
scsi host2: usb-storage 1-3:1.0
scsi host2: runtime PM trying to activate child device host2 but parent
(1-3:1.0) is not active
Digging into it it seems to be related to the problem described in the
commit message for cd998ded5c "i2c: designware: Prevent runtime
suspend during adapter registration" as scsi_add_host also calls
device_add and after the call to device_add the parent device is
suspended.
Fix this by using the approach from the mentioned commit and getting
the runtime pm reference before calling scsi_add_host.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The driver enforces a strict one-to-one relationship between the
received RESPONSE_AVAILABLE notifications and messages read from
the device. At the same time, it will cancel the interrupt URB
when there is no client holding the character device open.
Many devices do not cope well with this behaviour. They maintain
a FIFO queue of messages, and send notifications on a best effort
basis. Messages are queued regardless of whether the notification
is successful or not. So if the driver loses a single notification,
which can easily happen when the interrupt URB is cancelled, then
the device and driver becomes out-of-sync. New messages end up
at the end of the queue, while the associated notification makes
the driver read only the first message from the queue.
This state is permanent from a user point of view. There is no
no way to flush the device queue without resetting the device or
using another driver.
The problem is easy to hit with current QMI and MBIM command line
tools, which typically close the character device after seeing
the reply they expect. Any pending unsolicited messages from the
device will then trigger the driver bug.
Fix by always reading all queued messages from the device when
the notification URB is first submitted. This is expected to
end with an -EPIPE status when there are no more pending
messages, so demote the printk associated with -EPIPE to debug
level.
The workaround has been tested on a large number of different MBIM
and QMI devices, as well as the Ericsson F5521gw and H5321gw modems
with real Device Management functions.
Signed-off-by: Bjørn Mork <bjorn@mork.no>
Acked-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
alloc_ordered_workqueue replaces the deprecated
create_singlethread_workqueue.
There are multiple work items on the work queue, which require
ordering. Hence, an ordered workqueue has been used.
The workqueue "wq_otg" is not being used on a memory reclaim path.
Hence, WQ_MEM_RECLAIM has not been set.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The status workqueue is involved in initializing the Uxxx and polling
the Uxxx until a supported PCMCIA CardBus device is detected.
It then starts the command and respond workqueues and then loads the
module that handles the device, after which it just polls the Uxxx
looking for card ejects.
The command and respond workqueues are involved in implementing a command
sequencer for communicating with the firmware on the other side of
the FTDI chip in the Uxxx.
These workqueues have only a single work item each and hence they do not
require ordering. Also, none of the above workqueues are being used on a
memory recliam path. Hence, the singlethreaded workqueues have been
replaced with the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
The work items have been sync cancelled because they are self-requeueing
and need to wait for the in-flight work item to finish before proceeding
with destruction. Hence, they have been sync cancelled in
ftdi_status_cancel_work(), ftdi_command_cancel_work() and
ftdi_response_cancel_work(). These functions are called in
ftdi_elan_exit() to ensure that there are no pending work items while
disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The workqueue "wq" is involved in controlling the brightness of an
Apple Cinema Display over USB.
It has a single work item(&pdata->work) per appledisplay and hence
doesn't require ordering. Also, it is not being used on a memory
reclaim path.
Hence, the singlethreaded workqueue has been replaced with the use of
system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
The work item is self-requeueing and needs to wait for the in-flight
work item to finish before proceeding with destruction.
Hence, it has been sync cancelled in appledisplay_disconnect().
This also ensures that there are no pending tasks while disconnecting
the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The workqueue has a single work item(&lvs->rh_work) and hence
doesn't require ordering. Also, it is not being used on a memory
reclaim path. Hence, the singlethreaded workqueue has been replaced
with the use of system_wq.
System workqueues have been able to handle high level of concurrency
for a long time now and hence it's not required to have a singlethreaded
workqueue just to gain concurrency. Unlike a dedicated per-cpu workqueue
created with create_singlethread_workqueue(), system_wq allows multiple
work items to overlap executions even on the same CPU; however, a
per-cpu workqueue doesn't have any CPU locality or global ordering
guarantee unless the target CPU is explicitly specified and thus the
increase of local concurrency shouldn't make any difference.
The work item has been flushed in lvs_rh_disconnect() to ensure that
there are no pending tasks while disconnecting the driver.
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use of_property_read_bool to check for the existence of a property.
The semantic patch that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e1,e2,x;
@@
- if (of_get_property(e1,e2,NULL))
- x = true;
- else
- x = false;
+ x = of_property_read_bool(e1,e2);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This is a minimal driver to support bringing a usb4604 device
from microchip out of reset and into hub mode. The usb4604 device
is related to the usb3503 device, but it didn't seem close enough
to warrant putting both into the same file. This patch borrows
some of the usb3503 structure and trims it down to just handle
the optional reset gpio and adds the i2c command to put the
device into hub mode.
Datasheet: http://ww1.microchip.com/downloads/en/DeviceDoc/00001716A.pdf
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch fixes fives off-by-one bugs in the ftdi-elan driver code. The
bug can be triggered by plugging a USB adapter for CardBus 3G cards (model
U132 manufactured by Elan Digital Systems, Ltd), causing a kernel panic.
The fix was tested on Ubuntu 14.04.4 with 4.7.0-rc14.2.0-27-generic+ and
4.4.0-22-generic+ kernel. In the ftdi_elan_synchronize function, an
off-by-one memory corruption occurs when packet_bytes is equal or bigger
than m. After having read m bytes, that is bytes_read is equal to m, "
..\x00" is still copied to the stack variable causing an out bounds write
of 4 bytes, which overwrites the stack canary and results in a kernel
panic.
This off-by-one requires physical access to the machine. It is not
exploitable since we have no control on the overwritten data. Similar
off-by-one bugs have been observed in 4 other functions:
ftdi_elan_stuck_waiting, ftdi_elan_read, ftdi_elan_edset_output and
ftdi_elan_flush_input_fifo.
Reported-by: Alex Palesandro <palexster@gmail.com>
Signed-off-by: Xiao Han <xiao.han@orange.fr>
Tested-by: Paul Chaignon <pchaigno@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
For case 14 and case 21, their correct return value is the number
of bytes transferred, so it is a positive integer. But in usbtest_ioctl,
it takes non-zero as false return value for usbtest_do_ioctl, so
it will treat the correct test as wrong test, then the time on
tests will be the minus value.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Cc: stable <stable@vger.kernel.org>
Fixes: 18fc4ebdc7 ("usb: misc: usbtest: Remove timeval usage")
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The locking in hub_activate() is not adequate to provide full mutual
exclusion with hub_quiesce(). The subroutine locks the hub's
usb_interface, but the callers of hub_quiesce() (such as
hub_pre_reset() and hub_event()) hold the lock to the hub's
usb_device.
This patch changes hub_activate() to make it acquire the same lock as
those other routines.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org> #4.4+
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The early-exit pathway in hub_activate, added by commit e50293ef97
("USB: fix invalid memory access in hub_activate()") needs
improvement. It duplicates code that is already present at the end of
the subroutine, and it neglects to undo the effect of a
usb_autopm_get_interface_no_resume() call.
This patch fixes both problems by making the early-exit pathway jump
directly to the end of the subroutine. It simplifies the code at the
end by merging two conditionals that actually test the same condition
although they appear different: If type < HUB_INIT3 then type must be
either HUB_INIT2 or HUB_INIT, and it can't be HUB_INIT because in that
case the subroutine would have exited earlier.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: <stable@vger.kernel.org> #4.4+
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Memory leak and unbalanced reference count:
If the hub gets disconnected while the core is still activating it, this
can result in leaking memory of few USB structures.
This will happen if we have done a kref_get() from hub_activate() and
scheduled a delayed work item for HUB_INIT2/3. Now if hub_disconnect()
gets called before the delayed work expires, then we will cancel the
work from hub_quiesce(), but wouldn't do a kref_put(). And so the
unbalance.
kmemleak reports this as (with the commit e50293ef97 backported to
3.10 kernel with other changes, though the same is true for mainline as
well):
unreferenced object 0xffffffc08af5b800 (size 1024):
comm "khubd", pid 73, jiffies 4295051211 (age 6482.350s)
hex dump (first 32 bytes):
30 68 f3 8c c0 ff ff ff 00 a0 b2 2e c0 ff ff ff 0h..............
01 00 00 00 00 00 00 00 00 94 7d 40 c0 ff ff ff ..........}@....
backtrace:
[<ffffffc0003079ec>] create_object+0x148/0x2a0
[<ffffffc000cc150c>] kmemleak_alloc+0x80/0xbc
[<ffffffc000303a7c>] kmem_cache_alloc_trace+0x120/0x1ac
[<ffffffc0006fa610>] hub_probe+0x120/0xb84
[<ffffffc000702b20>] usb_probe_interface+0x1ec/0x298
[<ffffffc0005d50cc>] driver_probe_device+0x160/0x374
[<ffffffc0005d5308>] __device_attach+0x28/0x4c
[<ffffffc0005d3164>] bus_for_each_drv+0x78/0xac
[<ffffffc0005d4ee0>] device_attach+0x6c/0x9c
[<ffffffc0005d42b8>] bus_probe_device+0x28/0xa0
[<ffffffc0005d23a4>] device_add+0x324/0x604
[<ffffffc000700fcc>] usb_set_configuration+0x660/0x6cc
[<ffffffc00070a350>] generic_probe+0x44/0x84
[<ffffffc000702914>] usb_probe_device+0x54/0x74
[<ffffffc0005d50cc>] driver_probe_device+0x160/0x374
[<ffffffc0005d5308>] __device_attach+0x28/0x4c
Deadlocks:
If the hub gets disconnected early enough (i.e. before INIT2/INIT3 are
finished and the init_work is still queued), the core may call
hub_quiesce() after acquiring interface device locks and it will wait
for the work to be cancelled synchronously. But if the work handler is
already running in parallel, it may try to acquire the same interface
device lock and this may result in deadlock.
Fix both the issues by removing the call to cancel_delayed_work_sync().
CC: <stable@vger.kernel.org> #4.4+
Fixes: e50293ef97 ("USB: fix invalid memory access in hub_activate()")
Reported-by: Manu Gautam <mgautam@codeaurora.org>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
udriver struct allocated by kzalloc() will not be freed
if usb_register() and next calls fail. This patch fixes this
by adding one more step with kfree(udriver) in error path.
Signed-off-by: Alexey Klimov <klimov.linux@gmail.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds a set of compositions for Telit LE920A4.
Compositions in short are:
0x1207: tty + tty
0x1208: tty + adb + tty + tty
0x1211: tty + adb + ecm
0x1212: tty + adb
0x1213: ecm + tty
0x1214: tty + adb + ecm + tty
telit_le922_blacklist_usbcfg3 is reused for compositions 0x1211
and 0x1214 due to the same interfaces positions.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
BCM20706V2_EVAL is a WICED dev board designed with FT2232H USB 2.0
UART/FIFO IC.
To support BCM920706V2_EVAL dev board for WICED development on Linux.
Add the VID(0a5c) and PID(6422) to ftdi_sio driver to allow loading
ftdi_sio for this board.
Signed-off-by: Sheng-Hui J. Chu <s.jeffrey.chu@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Ivium Technologies uses the FTDI VID with custom PIDs for their line of
electrochemical interfaces and the PalmSens they developed for PalmSens
BV.
Signed-off-by: Robert Delien <robert@delien.nl>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
The device has four interfaces; the three serial ports ought to be
handled by this driver:
00 Diagnostic interface serial port
01 NMEA device serial port
02 Mass storage (sd card)
03 Modem serial port
The other product ids listed in the Windows driver are present already.
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Here are a few more straggler patches for USB for 4.8-rc1. Most of
these are for the usb-serial driver tree. All of those have been in
linux-next for a long time, but missed my previous pull request to you.
The remaining change is to fix up a staging tree build error, due to
some USB gadget driver changes that went in. I put it in this tree as
it was for a USB driver and people are reporting the build error on your
tree.
All of these have been in linux-next for this week, and longer for the
usb-serial changes.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iFYEABECABYFAlek9msPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspyfUAoKJd
y5i3QB5LqqWayQ/UrqoVGEfSAJ9Pz3ffwuvM07+sMPP7X1NYcEw+7A==
=q4ki
-----END PGP SIGNATURE-----
Merge tag 'usb-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull more USB updates from Greg KH:
"Here are a few more straggler patches for USB for 4.8-rc1.
Most of these are for the usb-serial driver tree. All of those have
been in linux-next for a long time, but missed my previous pull
request to you.
The remaining change is to fix up a staging tree build error, due to
some USB gadget driver changes that went in. I put it in this tree as
it was for a USB driver and people are reporting the build error on
your tree.
All of these have been in linux-next for this week, and longer for the
usb-serial changes"
* tag 'usb-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
staging: emxx_udc: allow modular build
USB: serial: use variable for status
USB: serial: option: add support for Telit LE910 PID 0x1206
USB: serial: cp210x: use kmemdup
USB: serial: ti_usb_3410_5052: use functions rather than macros
USB: serial: ti_usb_3410_5052: remove ti_usb_3410_5052.h
USB: serial: ti_usb_3410_5052: use __packed
USB: serial: ti_usb_3410_5052: remove useless comments
Pull HID updates from Jiri Kosina:
- new hid-alps driver for ALPS Touchpad-Stick device, from Masaki Ota
- much improved and generalized HID led handling, and merge of
specialized hid-thingm driver into this generic hid-led one, from
Heiner Kallweit
- i2c-hid power management improvements from Fu Zhonghui and Guohua
Zhong
- uhid initialization race fix from Roderick Colenbrander
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (21 commits)
HID: add usb device id for Apple Magic Keyboard
HID: hid-led: fix Delcom support on big endian systems
HID: hid-led: add support for Greynut Luxafor
HID: hid-led: add support for Delcom Visual Signal Indicator G2
HID: hid-led: remove report id from struct hidled_config
HID: alps: a few cleanups
HID: remove ThingM blink(1) driver
HID: hid-led: add support for ThingM blink(1)
HID: hid-led: add support for reading from LED devices
HID: hid-led: add support for devices with multiple independent LEDs
HID: i2c-hid: set power sleep before shutdown
HID: alps: match alps devices in core
HID: thingm: simplify debug output code
HID: alps: pass correct sizes to hid_hw_raw_request()
HID: alps: struct u1_dev *priv is internal to the driver
HID: add Alps I2C HID Touchpad-Stick support
HID: led: fix config
usb: misc: remove outdated USB LED driver
HID: migrate USB LED driver from usb misc to hid
HID: i2c_hid: enable i2c-hid devices to suspend/resume asynchronously
...
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=mrOW
-----END PGP SIGNATURE-----
Merge tag 'media/v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new framework support for HDMI CEC and remote control support
- new encoding codec driver for Mediatek SoC
- new frontend driver: helene tuner
- added support for NetUp almost universal devices, with supports
DVB-C/S/S2/T/T2 and ISDB-T
- the mn88472 frontend driver got promoted from staging
- a new driver for RCar video input
- some soc_camera legacy drivers got removed: timb, omap1, mx2, mx3
- lots of driver cleanups, improvements and fixups
* tag 'media/v4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (377 commits)
[media] cec: always check all_device_types and features
[media] cec: poll should check if there is room in the tx queue
[media] vivid: support monitor all mode
[media] cec: fix test for unconfigured adapter in main message loop
[media] cec: limit the size of the transmit queue
[media] cec: zero unused msg part after msg->len
[media] cec: don't set fh to NULL in CEC_TRANSMIT
[media] cec: clear all status fields before transmit and always fill in sequence
[media] cec: CEC_RECEIVE overwrote the timeout field
[media] cxd2841er: Reading SNR for DVB-C added
[media] cxd2841er: Reading BER and UCB for DVB-C added
[media] cxd2841er: fix switch-case for DVB-C
[media] cxd2841er: fix signal strength scale for ISDB-T
[media] cxd2841er: adjust the dB scale for DVB-C
[media] cxd2841er: provide signal strength for DVB-C
[media] cxd2841er: fix BER report via DVBv5 stats API
[media] mb86a20s: apply mask to val after checking for read failure
[media] airspy: fix error logic during device register
[media] s5p-cec/TODO: add TODO item
[media] cec/TODO: drop comment about sphinx documentation
...
Pull crypto updates from Herbert Xu:
"Here is the crypto update for 4.8:
API:
- first part of skcipher low-level conversions
- add KPP (Key-agreement Protocol Primitives) interface.
Algorithms:
- fix IPsec/cryptd reordering issues that affects aesni
- RSA no longer does explicit leading zero removal
- add SHA3
- add DH
- add ECDH
- improve DRBG performance by not doing CTR by hand
Drivers:
- add x86 AVX2 multibuffer SHA256/512
- add POWER8 optimised crc32c
- add xts support to vmx
- add DH support to qat
- add RSA support to caam
- add Layerscape support to caam
- add SEC1 AEAD support to talitos
- improve performance by chaining requests in marvell/cesa
- add support for Araneus Alea I USB RNG
- add support for Broadcom BCM5301 RNG
- add support for Amlogic Meson RNG
- add support Broadcom NSP SoC RNG"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (180 commits)
crypto: vmx - Fix aes_p8_xts_decrypt build failure
crypto: vmx - Ignore generated files
crypto: vmx - Adding support for XTS
crypto: vmx - Adding asm subroutines for XTS
crypto: skcipher - add comment for skcipher_alg->base
crypto: testmgr - Print akcipher algorithm name
crypto: marvell - Fix wrong flag used for GFP in mv_cesa_dma_add_iv_op
crypto: nx - off by one bug in nx_of_update_msc()
crypto: rsa-pkcs1pad - fix rsa-pkcs1pad request struct
crypto: scatterwalk - Inline start/map/done
crypto: scatterwalk - Remove unnecessary BUG in scatterwalk_start
crypto: scatterwalk - Remove unnecessary advance in scatterwalk_pagedone
crypto: scatterwalk - Fix test in scatterwalk_done
crypto: api - Optimise away crypto_yield when hard preemption is on
crypto: scatterwalk - add no-copy support to copychunks
crypto: scatterwalk - Remove scatterwalk_bytes_sglen
crypto: omap - Stop using crypto scatterwalk_bytes_sglen
crypto: skcipher - Remove top-level givcipher interface
crypto: user - Remove crypto_lookup_skcipher call
crypto: cts - Convert to skcipher
...
Mostly clean ups, including the first few patches of a major overhaul of
the ti_usb_3410_5052 driver.
Included is also a new option-driver device id.
Signed-off-by: Johan Hovold <johan@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJXldlqAAoJEEEN5E/e4bSVICsQAKEXBW9y0jmM+PUEHTgM2zeS
I6bYELcbMenMuH23rt3SRIOVnTp7q1SSFzq2do6a+mgiShtS3yx697/On7OnpKCl
1JMsdjPvYUW+s1JdcIYYxkGyovfoGEzEjvhLPQRC6RHcN0J3Tn2jYcL0iG+zN7be
pqaiNENjooYhfkcCK/czRoLEapQx7O1jfOypuSiFPIL65FfUCs7gRkRSB+tOezaI
gxsYuAECMay5TJ/SXzV1CE+rF9O8w/q61G6pmaWQsAflkBMy/arOsFJy0JPN53/J
+GVukWV4vhZUlqcQozDjtILCSCvvrSwKJA3/OSV4gdT4NvnMX7RFUwWzY8W/vwD5
qMXybVnMsrdaluRXeYg1pxemwUO9FcEL2cfTsgHdR7UnKHHLM6rd3k7Z0lr5xFOt
Bi1RFeOcvsQTc11Y2ScBAXoxAKGJ7LvSmTDDNPVjcGo6/3lcoj8vJU6GLS5JMVwA
BF87LTSXXZzzLZnIiaSuBFEaalFupyxhE+g1/pnhv5he8owJaRN1L3xzDsL+2KPL
31O27c+hcYqsSJjsRIswQcYHyzsMu47ydogq+1qWNnxBkJgAunnPZgAFMT23jsab
0RaHK4a9hy8J19X1wA2PVV/6H6KODlGuoenXTwIick+dyER073N9gR0NuA8vNFNL
Ui5w87QUvbaRaXJy2G9A
=dAVf
-----END PGP SIGNATURE-----
Merge tag 'usb-serial-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/johan/usb-serial into usb-testing
Johan writes:
USB-serial updates for v4.8-rc1
Mostly clean ups, including the first few patches of a major overhaul of
the ti_usb_3410_5052 driver.
Included is also a new option-driver device id.
Signed-off-by: Johan Hovold <johan@kernel.org>
Pull timer updates from Thomas Gleixner:
"This update provides the following changes:
- The rework of the timer wheel which addresses the shortcomings of
the current wheel (cascading, slow search for next expiring timer,
etc). That's the first major change of the wheel in almost 20
years since Finn implemted it.
- A large overhaul of the clocksource drivers init functions to
consolidate the Device Tree initialization
- Some more Y2038 updates
- A capability fix for timerfd
- Yet another clock chip driver
- The usual pile of updates, comment improvements all over the place"
* 'timers-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (130 commits)
tick/nohz: Optimize nohz idle enter
clockevents: Make clockevents_subsys static
clocksource/drivers/time-armada-370-xp: Fix return value check
timers: Implement optimization for same expiry time in mod_timer()
timers: Split out index calculation
timers: Only wake softirq if necessary
timers: Forward the wheel clock whenever possible
timers/nohz: Remove pointless tick_nohz_kick_tick() function
timers: Optimize collect_expired_timers() for NOHZ
timers: Move __run_timers() function
timers: Remove set_timer_slack() leftovers
timers: Switch to a non-cascading wheel
timers: Reduce the CPU index space to 256k
timers: Give a few structs and members proper names
hlist: Add hlist_is_singular_node() helper
signals: Use hrtimer for sigtimedwait()
timers: Remove the deprecated mod_timer_pinned() API
timers, net/ipv4/inet: Initialize connection request timers as pinned
timers, drivers/tty/mips_ejtag: Initialize the poll timer as pinned
timers, drivers/tty/metag_da: Initialize the poll timer as pinned
...
Here's the big USB driver update for 4.8-rc1. Lots of the normal stuff
in here, musb, gadget, xhci, and other updates and fixes. All of the
details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iFYEABECABYFAleVPioPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspB5AAnj7a
VJ2t2kcWzFUNQ6dyJrJCGGRAAKDZmb5CnOGeqJmdVpDzN1CGLYjfiw==
=47iA
-----END PGP SIGNATURE-----
Merge tag 'usb-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB updates from Greg KH:
"Here's the big USB driver update for 4.8-rc1. Lots of the normal
stuff in here, musb, gadget, xhci, and other updates and fixes. All
of the details are in the shortlog.
All of these have been in linux-next for a while with no reported
issues"
* tag 'usb-4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (169 commits)
cdc-acm: beautify probe()
cdc-wdm: use the common CDC parser
cdc-acm: cleanup error handling
cdc-acm: use the common parser
usbnet: move the CDC parser into USB core
usb: musb: sunxi: Simplify dr_mode handling
usb: musb: sunxi: make unexported symbols static
usb: musb: cppi41: add dma channel tracepoints
usb: musb: cppi41: move struct cppi41_dma_channel to header
usb: musb: cleanup cppi_dma header
usb: musb: gadget: add usb-request tracepoints
usb: musb: host: add urb tracepoints
usb: musb: add tracepoints to dump interrupt events
usb: musb: add tracepoints for register access
usb: musb: dsps: use musb register read/write wrappers instead
usb: musb: switch dev_dbg to tracepoints
usb: musb: add tracepoints support for debugging
usb: quirks: Add no-lpm quirk for Elan
phy: rcar-gen3-usb2: fix mutex_lock calling in interrupt
phy: rockhip-usb: use devm_add_action_or_reset()
...
This removes some overly long lines by renaming variables and giving
them local scope.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Now that the common parser resides in USB core, it can
be used for CDC-WDM.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
A small update to unify error handling during probe().
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This introduces the common parser for extra CDC headers now that it no longer
depends on usbnet.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The dependencies were impossible to handle preventing
drivers for CDC devices not which are not network drivers
from using the common parser.
Signed-off-by: Oliver Neukum <ONeukum@suse.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
phy-sun4i-usb now has proper dr_mode handling, it always registers an
extcon, and sends a notify with the mode (even when in peripheral- /
host-only mode) at least once.
So we can simply the sunxi musb glue by always registering its extcon
notifier and relying on sunxi_musb_work() to enable vbus when in
host-only mode.
This also enables host- and peripheral-only mode with vbus monitoring.
Tested-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The sunxi_musb_dma_controller_create and _destroy are not exported
or used outside the driver, so fix sparse warnings by making these
two static:
drivers/usb/musb/sunxi.c:357:23: warning: symbol 'sunxi_musb_dma_controller_create' was not declared. Should it be static?
drivers/usb/musb/sunxi.c:363:6: warning: symbol 'sunxi_musb_dma_controller_destroy' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Move struct cppi41_dma_channel to the header file so other modules can
use it.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
davinci.h is not required by cppi_dma.h but cppi_dma.c, so move the
include to the right place.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds tracepoints to dump musb interrupt events.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This adds tracepoints to musb register read/write wrappers to get
trace log for register access.
The default tacepoint log prefix here would be musb_readX/writeX(),
which is not much helpful. So this patch let the tracepoints use
__buildin_return_address(0) to print the caller funciton name to
provide more context of the register access.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
musb core already exports the register read/write wrappers, so clean up
the duplication in dsps glue.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
To avoid printk() overhead while debugging, this patch implements the
foundation of tracepoints logging for musb driver to make debug
easier.
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This patch turns status in a variable read once from the URB.
The long term plan is to deliver status to the callback.
In addition it makes the code a bit more elegant.
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
This patch adds support for 0x1206 PID of Telit LE910.
Since the interfaces positions are the same than the ones for
0x1043 PID of Telit LE922, telit_le922_blacklist_usbcfg3 is used.
Signed-off-by: Daniele Palmas <dnlplm@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
Use kmemdup when some other buffer is immediately copied into allocated
region. It replaces call to allocation followed by memcpy, by a single
call to kmemdup.
Signed-off-by: Muhammad Falak R Wani <falakreyaz@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Functions are preferable to macros resembling functions.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
[johan: drop inline keyword, move above calling function ]
Signed-off-by: Johan Hovold <johan@kernel.org>
The definitions in ti_usb_3410_5052.h are only used in
ti_usb_3410_5052.c.
The content of the header is copied in ti_usb_3410_5052.c.
Also correct a typo in macro TI_PIPE_MODE_CONTINOUS.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
[johan: actually remove the header file ]
Signed-off-by: Johan Hovold <johan@kernel.org>
__packed is preferred over __attribute__((packed)) for portability.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Remove lines commenting the obvious.
Remove vi related comment.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
BugLink: http://bugs.launchpad.net/bugs/1498667
As reported in BugLink, this device has an issue with Linux Power
Management so adding a quirk. This quirk was reccomended by Alan Stern:
http://lkml.iu.edu/hypermail/linux/kernel/1606.2/05590.html
Signed-off-by: Joseph Salisbury <joseph.salisbury@canonical.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXefulAAoJEHm+PkMAQRiG6nMH/2O1vcZeOtqmx2yCMUeXyKAT
wG88XflXzf3rM7C7TiObEYVf/bbLleJ7saDLEeic7ButD5gyYacIuzylVnrcqfBc
vinz4cOw5kvu9DrRkCKdOfiTAgwYtqQW+syJ8ZK4lPQuSxnPAs+F/FKSOpyUF5FN
Dngr520KjYKBEtn27W9UDPChFRwQoWAlaOC534eusaArCJtHGHHiuq5TEDn2EIo8
pUw2vwx5JiquSHOY34WLU7r+QoilovCQlUSsBQdLlPjfMB1QFtclPYa+5yEMjkT4
wusOUOfS/zK0rV6KnEdc/SkpiVX5C9WpFiWUOdEeJ5mZ+KijVkaOa9K1EDx8jSM=
=7Hwh
-----END PGP SIGNATURE-----
Merge tag 'v4.7-rc6' into patchwork
Linux 4.7-rc6
* tag 'v4.7-rc6': (1245 commits)
Linux 4.7-rc6
ovl: warn instead of error if d_type is not supported
MIPS: Fix possible corruption of cache mode by mprotect.
locks: use file_inode()
usb: dwc3: st: Use explicit reset_control_get_exclusive() API
phy: phy-stih407-usb: Use explicit reset_control_get_exclusive() API
phy: miphy28lp: Inform the reset framework that our reset line may be shared
namespace: update event counter when umounting a deleted dentry
9p: use file_dentry()
lockd: unregister notifier blocks if the service fails to come up completely
ACPI,PCI,IRQ: correct operator precedence
fuse: serialize dirops by default
drm/i915: Fix missing unlock on error in i915_ppgtt_info()
powerpc: Initialise pci_io_base as early as possible
mfd: da9053: Fix compiler warning message for uninitialised variable
mfd: max77620: Fix FPS switch statements
phy: phy-stih407-usb: Inform the reset framework that our reset line may be shared
usb: dwc3: st: Inform the reset framework that our reset line may be shared
usb: host: ehci-st: Inform the reset framework that our reset line may be shared
usb: host: ohci-st: Inform the reset framework that our reset line may be shared
...
Make this a proper typed array. Drop the old allocate context code since
that is no longer used.
Note that the memops functions now get a struct device pointer instead of
the struct device ** that was there initially (actually a void pointer to
a struct containing only a struct device pointer).
This code is now a lot cleaner.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
We now have implicit batching in the timer wheel. The slack API is no longer
used, so remove it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Andrew F. Davis <afd@ti.com>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Chris Mason <clm@fb.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: George Spelvin <linux@sciencehorizons.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Len Brown <lenb@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Mathias Nyman <mathias.nyman@intel.com>
Cc: Pali Rohár <pali.rohar@gmail.com>
Cc: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Rik van Riel <riel@redhat.com>
Cc: Sebastian Reichel <sre@kernel.org>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-block@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: linux-mmc@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: linux-usb@vger.kernel.org
Cc: netdev@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160704094342.189813118@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iQIcBAABCAAGBQJXdkJCAAoJEFGvii+H/Hdh4fIP/0U47cICszk6AkV2P3q3yRc6
RyIfjBddVxAnNnUQoJAkyDnZmZnCH33wMa3NG8BlXCrtPUSMoUkG78RIN6mWjgp6
pooaXBylqIiU4ZoyQVXvxTQZhM7u/ox+2InrXOeZXirkJvRY4GzwsNWtdhzclHq2
iM86K1cfaIPdJ4d3y7WF6/5DOsdMiYQUvmtxLEYTKgJgGvkgM/9I7Ws8vk3R0lXk
wO8EItxIZecAIEwfwI8HgYCoyPctevMSnXMTWAJTF+5m3Wprhhv0lEjCTEBHbmJb
kkrAr86tNj4nNVG9pQCDYL/XX0Zpub0vTA4+mPL5/WTrVpI/RRYlJXKIlR25vvlN
wlYRrY4mE4gKFJh7t6DhQiHdrrQcoWPymKZ7CSF2GZvc65xwBa0u3ZkeLhurgj0N
C8Zj7QRIqHfP4O8JDMRvuToWJWtc8sfSvh2Y9szkevwNjZjO9INSM/hStfJZ1S0E
EnZIcHSKehjdiLHiMgyWGRB3Fq24u41u8aVAGvCfCsSe7CZKYKzyAHEQSC7solSJ
GmbJ6F2gB65v62rNReZeP9NCc25fex7ZkdYMr6XYqrSh7GoxtF+9VPHEvYXs5BVK
+rVVCOvuvqSy4+oQ+N/0grLHIThqSVbAusXBSLFPykHO7R4Z30f3wIiSPTq8m2VW
c5qwGR4ceOBRrX8fQw0c
=PpU9
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-4.7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull more MFD fixes from Lee Jones:
"Apologies for missing these from the first pull request.
Final patches fixing Reset API change"
* tag 'mfd-fixes-4.7.1' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
usb: dwc3: st: Use explicit reset_control_get_exclusive() API
phy: phy-stih407-usb: Use explicit reset_control_get_exclusive() API
phy: miphy28lp: Inform the reset framework that our reset line may be shared
Here are a number of small USB and PHY driver fixes for 4.7-rc6.
Nothing major here, all are described in the shortlog below. All have
been in linux-next with no reported issues.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2
iFYEABECABYFAld2ljcPHGdyZWdAa3JvYWguY29tAAoJEDFH1A3bLfspN+sAn28Z
+GbDzyY5XwZ7Qs5/5uPYoGONAKCObDpgZr1A+/EMvDd57gfHWmFqTw==
=uYl3
-----END PGP SIGNATURE-----
Merge tag 'usb-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB and PHY fixes from Greg KH:
"Here are a number of small USB and PHY driver fixes for 4.7-rc6.
Nothing major here, all are described in the shortlog below. All have
been in linux-next with no reported issues"
* tag 'usb-4.7-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
USB: don't free bandwidth_mutex too early
USB: EHCI: declare hostpc register as zero-length array
phy-sun4i-usb: Fix irq free conditions to match request conditions
phy: bcm-ns-usb2: checking the wrong variable
phy-sun4i-usb: fix missing __iomem *
phy: phy-sun4i-usb: Fix optional gpios failing probe
phy: rockchip-dp: fix return value check in rockchip_dp_phy_probe()
phy: rcar-gen3-usb2: fix unexpected repeat interrupts of VBUS change
usb: common: otg-fsm: add license to usb-otg-fsm
Looks like we lost all changes related to
commit 9522def400 ("usb: dwc3: core: cleanup IRQ resources") in host.c
when Felipe's next branch was merged into Greg's next branch.
Fixes 215db94818 ("Merge tag 'usb-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next")
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
gcc warns about what first looks like a reference to an uninitialized
variable:
drivers/usb/host/xhci-ring.c: In function 'handle_cmd_completion':
drivers/usb/host/xhci-ring.c:753:4: error: 'ep_ring' may be used uninitialized in this function [-Werror=maybe-uninitialized]
xhci_unmap_td_bounce_buffer(xhci, ep_ring, cur_td);
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/usb/host/xhci-ring.c:647:20: note: 'ep_ring' was declared here
struct xhci_ring *ep_ring;
^~~~~~~
It's clear to see that the list_empty() check means it can never be
uninitialized, however it still looks wrong:
When ep->cancelled_td_list contains more than one entry, the
ep_ring variable will point to the ring that was retrieved
from the last urb, and we have to look it up again in the
second loop instead, which fixes the behavior and gets rid of the
warning too.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: f9c589e142 ("xhci: TD-fragment, align the unsplittable case with a bounce buffer")
Acked-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Below are changes for v4.8-rc1, none is important, only the documentation
update for chipidea.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXddAGAAoJEEhZKYFQ1nG7ib0H/2dJjm/gd3X8O5kcLtIp/xl2
4r9jw14uIXMDSkfYqDNCiT/81buaGh3966Ke9I5eAjrES20Xsauk0atHpSmk0TXj
nVmwDKjnRjlIgi85pvneLt1IiphCkkW2d1EcFPNzpq4lEP2ZphwPw/laCywbc7qk
9BN7ennwxHHuDTK4+avuotF4HTEqOZOTbnnhlH3c7Mx+JFW+EMUOeRGKkEksv9d4
qMhSERKKK4UEXcfReRgMUnvZP30DPp6bE7jC5Hc/ymhp1hV0BGY64FfzATHIRO+t
rXMvjk2DI50BUL9K/bXoEQwqDmkwaY1cxsYlxKA/V7FFY8UnX41KWQ6HablXr50=
=jlT2
-----END PGP SIGNATURE-----
Merge tag 'usb-v4.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-next
Peter writes:
Hi Greg,
Below are changes for v4.8-rc1, none is important, only the documentation
update for chipidea.
We're making all reset line users specify whether their lines are
shared with other IP or they operate them exclusively. In this case
the line is exclusively used only by this IP, so use the *_exclusive()
API accordingly.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
- Use new reset_*_get_shared() variant to prevent reset line obtainment failure
- Fixes: 0b52297 ("reset: Add support for shared reset controls")
- Fix unintentional switch() fall-through into error path
- Fix uninitialised variable compiler warning
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=mo7m
-----END PGP SIGNATURE-----
Merge tag 'mfd-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD fixes from Lee Jones:
"Contained are some standard fixes and unusually an extension to the
Reset API. Some of those changes are required to fix a bug introduced
in -rc1, which introduces extra 'reset line checks' i.e. whether the
line is shared or not. If a line is shared and the new *_shared() API
is not used, the request fails with an error. This breaks USB in v4.7
for ST's platforms.
Admittedly, there are some patches contained in our (MFD/Reset)
immutable branch which are not true -fixes, but there isn't anything I
can do about that. Rest assured though, there aren't any API
'changes'. Everything is the same from the consumer's perspective.
- Use new reset_*_get_shared() variant to prevent reset line
obtainment failure (Fixes commit 0b52297f2288: "reset: Add support
for shared reset controls")
- Fix unintentional switch() fall-through into error path
- Fix uninitialised variable compiler warning"
* tag 'mfd-fixes-4.7' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: da9053: Fix compiler warning message for uninitialised variable
mfd: max77620: Fix FPS switch statements
phy: phy-stih407-usb: Inform the reset framework that our reset line may be shared
usb: dwc3: st: Inform the reset framework that our reset line may be shared
usb: host: ehci-st: Inform the reset framework that our reset line may be shared
usb: host: ohci-st: Inform the reset framework that our reset line may be shared
reset: TRIVIAL: Add line break at same place for similar APIs
reset: Supply *_shared variant calls when using *_optional APIs
reset: Supply *_shared variant calls when using of_* API
reset: Ensure drivers are explicit when requesting reset lines
reset: Reorder inline reset_control_get*() wrappers
On the STiH410 B2120 development board the MiPHY28lp shares its reset
line with the Synopsys DWC3 SuperSpeed (SS) USB 3.0 Dual-Role-Device
(DRD). New functionality in the reset subsystems forces consumers to
be explicit when requesting shared/exclusive reset lines.
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On the STiH410 B2120 development board the ST EHCI IP shares its reset
line with the OHCI IP. New functionality in the reset subsystems forces
consumers to be explicit when requesting shared/exclusive reset lines.
Acked-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
On the STiH410 B2120 development board the ST EHCI IP shares its reset
line with the OHCI IP. New functionality in the reset subsystems forces
consumers to be explicit when requesting shared/exclusive reset lines.
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Here's the big pull request for Peripheral stack and
all related drivers.
This time around with 109 non-merge commits mostly
concentrated on drivers/usb/gadget/udc (41.5%) and
drivers/usb/dwc3 (28.1%).
There's a big rework on dwc3's transfer handling
which gave us almost 3x faster USB3 speeds with Mass
Storage on a particular test scenario I measured. We
are also removing platform_data from dwc3 after
converting all users to built-in properties instead.
For the Gadget API, we're just adding tracepoints to
aid debugging activities.
Other than these, there's the usual set of spelling
fixes, minor bug fixes and sparse warnings cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=PT1e
-----END PGP SIGNATURE-----
Merge tag 'usb-for-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-next
Felipe writes:
usb: patches for v4.8 merge window
Here's the big pull request for Peripheral stack and
all related drivers.
This time around with 109 non-merge commits mostly
concentrated on drivers/usb/gadget/udc (41.5%) and
drivers/usb/dwc3 (28.1%).
There's a big rework on dwc3's transfer handling
which gave us almost 3x faster USB3 speeds with Mass
Storage on a particular test scenario I measured. We
are also removing platform_data from dwc3 after
converting all users to built-in properties instead.
For the Gadget API, we're just adding tracepoints to
aid debugging activities.
Other than these, there's the usual set of spelling
fixes, minor bug fixes and sparse warnings cleanups.
This patch fixes an issue that the CFIFOSEL register value is possible
to be changed by usbhsg_ep_enable() wrongly. And then, a data transfer
using CFIFO may not work correctly.
For example:
# modprobe g_multi file=usb-storage.bin
# ifconfig usb0 192.168.1.1 up
(During the USB host is sending file to the mass storage)
# ifconfig usb0 down
In this case, since the u_ether.c may call usb_ep_enable() in
eth_stop(), if the renesas_usbhs driver is also using CFIFO for
mass storage, the mass storage may not work correctly.
So, this patch adds usbhs_lock() and usbhs_unlock() calling in
usbhsg_ep_enable() to protect CFIFOSEL register. This is because:
- CFIFOSEL.CURPIPE = 0 is also needed for the pipe configuration
- The CFIFOSEL (fifo->sel) is already protected by usbhs_lock()
Fixes: 97664a207b ("usb: renesas_usbhs: shrink spin lock area")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes an issue that the xfer_work() is possible to cause
NULL pointer dereference if the usb cable is disconnected while data
transfer is running.
In such case, a gadget driver may call usb_ep_disable()) before
xfer_work() is actually called. In this case, the usbhs_pkt_pop()
will call usbhsf_fifo_unselect(), and then usbhs_pipe_to_fifo()
in xfer_work() will return NULL.
Fixes: e73a989 ("usb: renesas_usbhs: add DMAEngine support")
Cc: <stable@vger.kernel.org> # v3.1+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Return -ENOMEM if kmalloc() fails.
Fixes: 9353afbbfa ('usb: gadget: f_fs: buffer data from ‘oversized’ OUT requests')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The driver selects NOP_USB_XCEIV, which can only be built-in if
USB_GADGET is either disabled or also built-in, so with USB_DWC2_PCI=y
and USB_GADGET=m, NOP_USB_XCEIV is also built-in and we get this link
error:
drivers/usb/built-in.o: In function `nop_set_peripheral':
(text+0x1927c): undefined reference to `usb_gadget_vbus_connect'
drivers/usb/built-in.o: In function `nop_gpio_vbus_thread':
(text+0x197a0): undefined reference to `usb_gadget_vbus_connect'
(text+0x19830): undefined reference to `usb_gadget_vbus_disconnect'
This adds the same dependency for the dwc2 driver to avoid that
broken configuration.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As cat_printf() uses printf format strings in its parameters, adding
__printf attribute allows the compiler to detect at compile-time some
errors related to format strings (with -Wformat warning flag).
Signed-off-by: Nicolas Iooss <nicolas.iooss_linux@m4x.org>
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
To know why the driver probing failed, this patch shows error code.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The USB core contains a bug that can show up when a USB-3 host
controller is removed. If the primary (USB-2) hcd structure is
released before the shared (USB-3) hcd, the core will try to do a
double-free of the common bandwidth_mutex.
The problem was described in graphical form by Chung-Geol Kim, who
first reported it:
=================================================
At *remove USB(3.0) Storage
sequence <1> --> <5> ((Problem Case))
=================================================
VOLD
------------------------------------|------------
(uevent)
________|_________
|<1> |
|dwc3_otg_sm_work |
|usb_put_hcd |
|peer_hcd(kref=2)|
|__________________|
________|_________
|<2> |
|New USB BUS #2 |
| |
|peer_hcd(kref=1) |
| |
--(Link)-bandXX_mutex|
| |__________________|
|
___________________ |
|<3> | |
|dwc3_otg_sm_work | |
|usb_put_hcd | |
|primary_hcd(kref=1)| |
|___________________| |
_________|_________ |
|<4> | |
|New USB BUS #1 | |
|hcd_release | |
|primary_hcd(kref=0)| |
| | |
|bandXX_mutex(free) |<-
|___________________|
(( VOLD ))
______|___________
|<5> |
| SCSI |
|usb_put_hcd |
|peer_hcd(kref=0) |
|*hcd_release |
|bandXX_mutex(free*)|<- double free
|__________________|
=================================================
This happens because hcd_release() frees the bandwidth_mutex whenever
it sees a primary hcd being released (which is not a very good idea
in any case), but in the course of releasing the primary hcd, it
changes the pointers in the shared hcd in such a way that the shared
hcd will appear to be primary when it gets released.
This patch fixes the problem by changing hcd_release() so that it
deallocates the bandwidth_mutex only when the _last_ hcd structure
referencing it is released. The patch also removes an unnecessary
test, so that when an hcd is released, both the shared_hcd and
primary_hcd pointers in the hcd's peer will be cleared.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Chung-Geol Kim <chunggeol.kim@samsung.com>
Tested-by: Chung-Geol Kim <chunggeol.kim@samsung.com>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The usbhs_write32 function is not used outside of the rcar3.c
file, so fix the following sparse warning by making it static:
drivers/usb/renesas_usbhs/rcar3.c:26:6: warning: symbol 'usbhs_write32' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The Kconfig currently controlling compilation of this code is:
arch/x86/Kconfig.debug:config EARLY_PRINTK_DBGP
arch/x86/Kconfig.debug: bool "Early printk via EHCI debug port"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity so that when reading the
driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
No more users for it.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This should allow xhci to remove handling of platform data.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Requesting the only property that the driver needs using the
unified device property interface so it will be available
for all types of platforms, not just the ones using DT.
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It's only used with rings that have link trbs
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Only used in one place, replace with trb_is_link() helper
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
inc_deq() is called both for rings with link trbs and the event ring
without link trbs.
The last_trb() check in inc_deq() has a off by one error, going beyond
allocated array when checking if trb == [TRBS_PER_SEGMENT], and the whole
inc_deq() depend on this.
Rewrite the inc_deq() funciton, remove the faulty last_trb() helper, add
new last_trb_on_seg() and last_trb_on_ring() helpers
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Add a new is_link_trb() function that only checks for link trbs.
We want to split generic last_trb() function which is used for both
event rings without link trbs, and endpoint and command rings with links.
This will allow us to easier check for link trbs added mid segments.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Remove the event ring related checks in inc_enq()
Host hardware is the producer of events on the event ring,
driver will not queue anything, or call inc_enq() for the
event ring.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If the last trb before a link is not packet size aligned, and is not
splittable then use a bounce buffer for that chunk of max packet size
unalignable data.
Allocate a max packet size bounce buffer for every segment of a bulk
endpoint ring at the same time as allocating the ring.
If we need to align the data before the link trb in that segment then
copy the data to the segment bounce buffer, dma map it, and enqueue it.
Once the td finishes, or is cancelled, unmap it.
For in transfers we need to first map the bounce buffer, then queue it,
after it finishes, copy the bounce buffer to the original sg list, and
finally unmap it
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
TD fragments section 4.11.7.1 in xhci specs have additional requirements
on how trbs in TDs must be organized.
TD fragments shall not span transfer ring segments and TD fragments must
be packet aligned. Normally we don't care about TD fragments, on TD is one
big fragment, but if a TD spans ring segments it will be treated as two
fragments, and we need to comply with the alignment requirements.
For us this means that the payload data must be packet aligned in the
last trb before a link trb.
In most mass storage bulk tranfers we are lucky as the block size aligns
nicely with packet size, and there are no issues.
However, usb network adapters using scatterlists can hit this alignment
issue, and usbtest in kernel triggers this in minutes.
This patch is a partial solution, it solves the easy case when the last
trb before the link trb contains a packet boundary.
If that is the case then just split the trb at the boundary.
If not, then just print a debug message and continue as we have always
done, hoping for the best
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Queue trbs until all payload data in the urb is tranferred.
The actual number of trbs might need to change from the pre-calculated
number when the packet alignment restrictions for td fragments in
xhci 4.11.7.1 are taken into account.
Long term plan is to get rid of calculating the needed trbs in advance
all together. It's an unnecessary extra walk through the scatterlist.
This change also allows some bulk queue function simplifications
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
We only need to know if we are queuing the last trb for a TD when
calculating the td remainder field.
The total number of trbs left is not used.
We won't be able to trust the pre-calculated number of trbs used if we
need to align trb data by splitting or merging trbs in order to satisfy
comply with data alignment requirements in xhci specs section 4.11.7.1.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
If a zero-length packet is needed after a bulk transfer, then an
additional zero length TD was prepared before enqueueing the bulk transfer
This set up the zero packet TD structure with incorrect td->start_seg
and td->first_trb pointers.
Prepare the zero packet TD after the data bulk TD is enqueued instead.
It sets these pointers correctly.
This change also simplifies unnecessary complexity related to keeping
track of the last trb when enqueuing trbs.
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Tiny change, a bit more readable.
The real reason for this change is that the coming td fragment work
had several over 80 lines character lines split just because of a few
extra characters in variable names.
no functional changes
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Namely convert:
* IS_FG -> con_is_fg
* DO_UPDATE -> con_should_update
* CON_IS_VISIBLE -> con_is_visible
DO_UPDATE was a weird name for a yes/no answer, so the new name is
con_should_update.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
It is never called since commit 81732c3b2f (tty vt: Fix line
garbage in virtual console on command line edition) in 3.7. So remove
all the callbacks.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: linux-usb@vger.kernel.org
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Tomi Valkeinen <tomi.valkeinen@ti.com>
Cc: "James E.J. Bottomley" <jejb@parisc-linux.org>
Cc: Helge Deller <deller@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Cc: linux-parisc@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
bytes_written parameter of sisusb_copy_memory and sisusb_read_memory
is an out parameter, but its value is never used. So remove it and
pass a dummy variable down to sisusb_read_mem_bulk.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Thomas Winischhofer <thomas@winischhofer.net>
Cc: linux-usb@vger.kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJXaKhEAAoJEEhZKYFQ1nG7jWkH/1EzIv7rMrAtS6+GBqJO1ISD
F3LzTpYgjUOyz1MgnbSnqQjHivsxPoJLj7QK7sqcvsrKGoVAtnqBf80275N/gggf
CSjjYl+Bgw+F8oc7O/cUqTnj7oiNX6TLsIId2CEwcfxYxvkzSxwEQmB8CqMypASn
aBOKiBfCKdAI+N5gNRME+Y1Flmklrd/fTAuoNe9J3X6LlHRrKP1kjoE56rDyiwDx
VjdsP+PhTny/abnsNqA8k5776YHnsZwtl1vv4B+ndygNVjvSZ90czXsLow5LHAk4
r4TMqyX/g07nXGDTTOXRgq1wSoooebct245oZSuBCzOOIb8v/4bKgL/brkBHirg=
=TvYf
-----END PGP SIGNATURE-----
Merge tag 'usb-ci-v4.7-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/peter.chen/usb into usb-linus
Peter writes:
One fix for module support in OTG FSM
The usbhs_write32 function is not used outside of the rcar3.c
file, so fix the following sparse warning by making it static:
drivers/usb/renesas_usbhs/rcar3.c:26:6: warning: symbol 'usbhs_write32' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The above commit reordered spin_lock/unlock and now `&dev->lock' is acquired
(rather than released) before calling `dev->driver->disconnect',
`dev->driver->setup', `dev->driver->suspend', `usb_gadget_giveback_request', and
`usb_gadget_udc_reset'.
But this *may* not be the right way to fix the problem pointed by d3cb25a121.
Note that the other usb/gadget/udc drivers do release the lock before calling
these functions. There are also inconsistencies within pch_udc.c, where
`dev->driver->disconnect' is called while holding `&dev->lock' in lines 613 and
1184, but not in line 2739.
Finally, commit d3cb25a121 may have introduced several potential deadlocks.
For instance, EBA (https://github.com/models-team/eba) reports:
Double lock in drivers/usb/gadget/udc/pch_udc.c
first at 2791: spin_lock(& dev->lock); [pch_udc_isr]
second at 2694: spin_lock(& dev->lock); [pch_udc_svc_cfg_interrupt]
after calling from 2793: pch_udc_dev_isr(dev, dev_intr);
after calling from 2724: pch_udc_svc_cfg_interrupt(dev);
Similarly, other potential deadlocks are 2791 -> 2793 -> 2721 -> 2657; and
2791 -> 2793 -> 2711 -> 2573 -> 1499 -> 1480.
Fixes: d3cb25a121 ("usb: gadget: udc: fix spin_lock in pch_udc")
Signed-off-by: Iago Abal <mail@iagoabal.eu>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It had changed to be suspend event for BIT6 in DEVT register from
version 2.30a and above. Thus this patch introduces one suspend
event handler to handle the suspend event.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
As a preparation for another cleanup, this moves the header file
for the phy-msm-usb driver into the driver itself. No other file
includes it any more, and we don't really want it in the global
namespace anyway.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
f_fs rounds up read(2) requests to a multiple of a max packet size
which means that host may provide more data than user has space for.
So far, the excess data has been silently ignored.
This introduces a buffer for a tail of such requests so that they are
returned on next read instead of being ignored.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Add a pr_err when host sent more data then the size of the buffer user
space gave us. This may happen on UDCs which require OUT requests to
be aligned to max packet size. The patch includes a description of the
situation.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Space required after that ','.
Reviewed-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: Sandhya Bankar <bankarsandhya512@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes the following (W=1) warnings:
drivers/usb/gadget/udc/mv_u3d_core.c: In function ‘mv_u3d_process_ep_req’:
drivers/usb/gadget/udc/mv_u3d_core.c:124:6: warning: variable ‘trb_complete’ set but not used [-Wunused-but-set-variable]
int trb_complete, actual, remaining_length = 0;
^
drivers/usb/gadget/udc/mv_u3d_core.c:123:28: warning: variable ‘curr_ep_context’ set but not used [-Wunused-but-set-variable]
struct mv_u3d_ep_context *curr_ep_context;
^
drivers/usb/gadget/udc/mv_u3d_core.c:122:13: warning: variable ‘cur_deq_lo’ set but not used [-Wunused-but-set-variable]
dma_addr_t cur_deq_lo;
^
drivers/usb/gadget/udc/mv_u3d_core.c: In function ‘mv_u3d_ep_enable’:
drivers/usb/gadget/udc/mv_u3d_core.c:530:28: warning: variable ‘ep_context’ set but not used [-Wunused-but-set-variable]
struct mv_u3d_ep_context *ep_context;
^
drivers/usb/gadget/udc/mv_u3d_core.c: In function ‘mv_u3d_ep_disable’:
drivers/usb/gadget/udc/mv_u3d_core.c:636:28: warning: variable ‘ep_context’ set but not used [-Wunused-but-set-variable]
struct mv_u3d_ep_context *ep_context;
^
In doing so, it removes calls to ioread32 function which does I/O with
the device, but I hope the reads don’t have any side effects that are
needed.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes the following (W=1) warnings:
drivers/usb/gadget/udc/r8a66597-udc.c: In function ‘r8a66597_irq’:
drivers/usb/gadget/udc/r8a66597-udc.c:1468:15: warning: variable ‘nrdyenb’ set but not used [-Wunused-but-set-variable]
u16 brdyenb, nrdyenb, bempenb;
^
drivers/usb/gadget/udc/r8a66597-udc.c:1467:15: warning: variable ‘nrdysts’ set but not used [-Wunused-but-set-variable]
u16 brdysts, nrdysts, bempsts;
^
In doing so, it removes calls to r8a66597_read function which does I/O
with the device, but I hope the reads don’t have any side effects that
are needed.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This patch fixes the following (W=1) warnings:
drivers/usb/gadget/udc/m66592-udc.c: In function ‘m66592_irq’:
drivers/usb/gadget/udc/m66592-udc.c:1203:15: warning: variable ‘nrdyenb’ set but not used [-Wunused-but-set-variable]
u16 brdyenb, nrdyenb, bempenb;
^
drivers/usb/gadget/udc/m66592-udc.c:1202:15: warning: variable ‘nrdysts’ set but not used [-Wunused-but-set-variable]
u16 brdysts, nrdysts, bempsts;
^
In doing so, it removes calls to m66592_read function which does I/O
with the device, but I hope the reads don’t have any side effects that
are needed.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Those are enabled with W=1 make option.
The patch leaves of some type-limits warnings which are caused by
generic macros used in a way where they produce always-false
conditions.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Implementations might use different IRQs for
host, gadget so use named interrupt resources
to allow device tree to specify the interrupts.
Following are the interrupt names
Peripheral Interrupt - peripheral
HOST Interrupt - host
Maintain backward compatibility for a single named
interrupt ("dwc3_usb3") for all interrupts as well as
unnamed interrupt at index 0 for all interrupts.
As platform_get_irq() variants are used, tackle
the -EPROBE_DEFER case as well.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Some SoCs have a single phy-hw-block with multiple phys, this is
modelled by a single phy dts node, so we end up with multiple
controller nodes with a phys property pointing to the phy-node
of the otg-phy.
Only one of these controllers typically is an otg controller, yet we
were checking the first controller who uses a phy from the block and
then end up looking for a dr_mode property in e.g. the ehci controller.
This commit fixes this by adding an arg0 parameter to
of_usb_get_dr_mode_by_phy and make of_usb_get_dr_mode_by_phy
check that this matches the phandle args[0] value when looking for
the otg controller.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
The "atmel,at91sam9g45-udc" compatible UDC is also used on at91sam9x5 so it
is also necessary to try to get the syscon for at91sam9x5-pmc.
Fixes: 4747639f01 ("usb: gadget: atmel: access the PMC using regmap")
Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Done fixes and tested hsotg gadget's BDMA mode. Tested Control,
Bulk, Isoc, Inter transfers. Added code for isoc transfers,
removed unusable code, done minor fixes. Affected functions
and IRQ handlers:
- dwc2_hsotg_start_req(),
- dwc2_hsotg_ep_enable(),
- dwc2_hsotg_ep_queue(),
- dwc2_hsotg_handle_outdone(),
- GINTSTS_GOUTNAKEFF handler,
Removed 'has_correct_parity' flag from 'dwc2_hsotg_ep' struct.
Before this patch series, to set the data pid the DWC2 gadget
driver was toggling the even/odd until it match, then were
leaving it set. But now I have added mechanism to set pid and
excluded all code where this flag was set.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reimplemented EP disabled interrupt handler and moved to
corresponding function.
This interrupt indicates that the endpoint has been disabled per
the application's request.
For IN endpoints flushes txfifo, in case of BULK clears DCTL_CGNPINNAK,
in case of ISOC completes current request.
For ISOC-OUT endpoints completes expired requests. If there is
remaining request starts it. This is the part of ISOC-OUT transfer
drop flow. When ISOC-OUT transfer expired we must disable ep to drop
ongoing transfer.
Tested-by: John Keeping <john@metanate.com>
Reviewed-by: Vahram Aharonyan <vahrama@synopsys.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Incomplete ISO IN interrupt indicates one of the following conditions
occurred while transmitting an ISOC transaction.
- Corrupted IN Token for ISOC EP.
- Packet not complete in FIFO.
Incomplete ISO OUT indicates that there is at least one isochronous OUT
endpoint on which the transfer is not completed in the current
microframe.
The following actions will be taken:
In case of EP-IN
- Determine the EP
- Disable EP directly from this handler; when "Endpoint Disabled"
interrupt is received flush FIFO
In case of EP-OUT
- Determine the EP
- If target frame elapsed set DCTL_SGOUTNAK, unmask GOUTNAKEFF and
proceed as described in section 7.5.1 of DWC-HSOTG Programming Guide
Also added dwc2_gadget_target_frame_elapsed() helper function which
will be used in Incomplete ISO IN/OUT Interrupt handlers.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
NAKINTRPT interrupt is starting point for isoc-in transfer,
synchronization done with first in token received from host,
core asserts this interrupt when responds with 0 length data
to in token, received from host.
The first IN token is asynchronous for device - device does not
know when first one token will arrive from host. On first token
arrival HW generates 2 interrupts: 'in token received while FIFO
empty' and 'NAK'. NAK interrupt for ISOC in means that token has
arrived and ZLP was sent in response to that as there was no data
in FIFO. SW is basing on this interrupt to obtain frame in which
token has come and then based on the interval calculates next
frame for transfer.
OUTTKNEPDIS interrupt is starting point for isoc-out transfer,
synchronization done with first out token received from host
while corresponding ep is disabled.
For OUTs the reason is same - device does not know initial frame
in which out token will come. For this HW generates OUTTKNEPDIS
- out token is received while EP is disabled. Upon getting this
interrupt SW starts calculation for next transfer frame.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Replaced repeating code with function call.
Starts next request from ep queue.
If queue is empty and ep is isoc
-In case of OUT-EP unmasks OUTTKNEPDIS.
OUTTKNEPDIS is masked in it's handler, so we need to unmask it here
to be able to do resynchronization.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Reads and returns interrupts for given endpoint, by masking epint_reg
with corresponding mask.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Calculate the interval according to the USB 2.0 specification section
9.6.6.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Increases and checks targeted frame number of current ep
if overrun happened, sets flag and masks with DSTS_SOFFN_LIMIT
Added following fields to struct dwc2_hsotg_ep
-target_frame: Targeted frame num to setup next ISOC transfer
-frame_overrun: Indicates SOF number overrun in DSTS
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
According DWC-OTG databook, "GOUTNakEff" is read only and can be
cleared only by "DCTL.CGOUTNak", but here we do not need to clear
it because DWC-OTG programming guide says that before disabling
any OUT endpoint, the application must enable Global OUT NAK mode,
so if this mode is enabled we can continue without this step.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
No-op change. Changed field names to prevent misunderstanding.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
This chunk is not needed here. There is no functionality
depend on this, so if no-op, I think we do not need to have
this interrupt unmasked.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Removed "ctrl |= DXEPCTL_USBACTEP" from
dwc2_hsotg_start_req() function because this
step is done in dwc2_hsotg_ep_enable().
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Added register field definitions, register names are according
DWC-OTG databook.
Tested-by: John Keeping <john@metanate.com>
Signed-off-by: Vardan Mikayelyan <mvardan@synopsys.com>
Signed-off-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We get a warning for this when building with W=1 because the
argument gets assigned to something else but never read:
drivers/usb/gadget/udc/pxa27x_udc.c: In function 'stop_activity':
drivers/usb/gadget/udc/pxa27x_udc.c:1828:74: error: parameter 'driver' set but not used [-Werror=unused-but-set-parameter]
This remove the argument entirely.
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It will be crash to stop gadget when the dwc3 device had been into suspend
state, thus we need to check if the dwc3 device had been into suspend state
when UDC try to stop gadget.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Because of recent changes to transfer handling on
DWC3, we will not get XferComplete unless we
completely fill up our TRB ring. This means that we
might get a Reset or Disconnect without getting a
XferComplete first.
In order to correctly release our allocated Transfer
Resource, we must issue ENDTRANSFER command whenever
dep->resource_index is valid.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
If there is a failure after pm_runtime_enable/get_sync()
we need to call pm_runtime_disable/put_sync().
Otherwise it will lead to an unbalanced pm_runtime_enable() on the
subsequent probe if the earlier probe bailed out due to -EPROBE_DEFER.
pm_runtime_get_sync() can fail as well so deal with that case too.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
it's clear now that when is_on=true, we must loop
until DWC3_DSTS_DEVCTRLHLT clears; while when
is_on=false we must loop until DWC3_DSTS_DEVCTRLHLT
gets set.
Instead of adding actual if() statements, we can
rely on XOR operation to evaluate to true only when
the above conditions apply. Then, we can move the
break condition back to the while() statement
together with our timeout check and the resulting
code is very compact and simpler to read.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
instead of looping forever and forcing a return if
timeout reaches zero, we can just use timeout and
loop's break condition directly.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
testing shows that udelay() is unnecessary as
controller reaches Halted state almost
instantenously as can be seen by our timeout
variable never actually decrementing.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
We shouldn't change a host-only dwc3 to gadget-only
if driver is built as gadget-only. Fix that up here.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
It's know that Intel's SoCs' dwc3 integration is
peripheral-only since Intel implements its own
portmux for role-swapping. In order to prevent dwc3
from ever registering and XHCI platform_device,
let's just set dr-mode to peripheral-only on Intel
SoCs.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
'modify' is what the current action is called. Let's
rename it so it matches databook. While at that,
also make sure to add support 'init' action too.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
William Wu