Structures st_uvis25_i2c_regmap_config and st_uvis25_spi_regmap_config are
local to the source and do not need to be in global scope, so make them
both static.
Cleans up sparse warnings:
warning: symbol 'st_uvis25_i2c_regmap_config' was not declared. Should
it be static?
warning: symbol 'st_uvis25_spi_regmap_config' was not declared. Should
it be static?
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
add support for STMicroelectronics UVIS25 uv sensor
http://www.st.com/resource/en/datasheet/uvis25.pdf
- continuos mode support
- i2c support
- spi support
- trigger mode support
- system PM support
Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi83@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Driver for 20-bit ALS and UV B sensor with I2C interface exposing
the following API:
in_uvindex_input
in_illuminance_raw
in_illuminance_scale
in_illuminance_scale_available
in_intensity_uv_raw
in_intensity_uv_scale
in_intensity_uv_scale_available
integration_time
integration_time_available
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Fix gcc warnings about variable 'ec_device' being set but not used
in these files:
common/cros_ec_sensors/cros_ec_sensors.c:194:25
light/cros_ec_light_prox.c:184:25
Signed-off-by: Paolo Cretaro <paolocretaro@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd atomisp
cleanups (take the media tree's version).
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
iG0EABECAC0WIQT0tgzFv3jCIUoxPcsxR9QN2y37KQUCWgnFrg8cZ3JlZ0Brcm9h
aC5jb20ACgkQMUfUDdst+ymxbwCgtNlBkqD2JJYpLRKvI/C4w1vzZsEAnA2THRkt
g3ioPBqmqC/2DSbldr2o
=/ebw
-----END PGP SIGNATURE-----
Merge tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the "big" staging and IIO driver update for 4.15-rc1.
Lots and lots of little changes, almost all minor code cleanups as the
Outreachy application process happened during this development cycle.
Also happened was a lot of IIO driver activity, and the typec USB code
moving out of staging to drivers/usb (same commits are in the USB tree
on a persistent branch to not cause merge issues.)
Overall, it's a wash, I think we added a few hundred more lines than
removed, but really only a few thousand were modified at all.
All of these have been in linux-next for a while. There might be a
merge issue with Al's vfs tree in the pi433 driver (take his changes,
they are always better), and the media tree with some of the odd
atomisp cleanups (take the media tree's version)"
* tag 'staging-4.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (507 commits)
staging: lustre: add SPDX identifiers to all lustre files
staging: greybus: Remove redundant license text
staging: greybus: add SPDX identifiers to all greybus driver files
staging: ccree: simplify ioread/iowrite
staging: ccree: simplify registers access
staging: ccree: simplify error handling logic
staging: ccree: remove dead code
staging: ccree: handle limiting of DMA masks
staging: ccree: copy IV to DMAable memory
staging: fbtft: remove redundant initialization of buf
staging: sm750fb: Fix parameter mistake in poke32
staging: wilc1000: Fix bssid buffer offset in Txq
staging: fbtft: fb_ssd1331: fix mirrored display
staging: android: Fix checkpatch.pl error
staging: greybus: loopback: convert loopback to use generic async operations
staging: greybus: operation: add private data with get/set accessors
staging: greybus: loopback: Fix iteration count on async path
staging: greybus: loopback: Hold per-connection mutex across operations
staging: greybus/loopback: use ktime_get() for time intervals
staging: fsl-dpaa2/eth: Extra headroom in RX buffers
...
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The reported scale was only correct for the default settings of 100 ms
integration time and gain 1.
This aligns the reported scale with the behaviour of any other IIO driver
and the documented ABI, but may require userspace changes if someone uses
non-default settings.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of manually iterating the array of allowed gain values, use
find_closest. Storing the current gain setting avoids accessing the
hardware on each query.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Instead of reading the value from the register on each query, store the
set value.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
This improves code uniformity (range checks for als_gain are also done
in the setter). Also unmangle rounding and calculation of register value.
The calculated integration time it_ms is required in the next patch of
the series.
Signed-off-by: Stefan Brüns <stefan.bruens@rwth-aachen.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The TCS3472 device provides interrupt signal for out-of-threshold events
with persistence filter.
This change adds interrupt support for the threshold events and enables
to configure the period of time by persistence filter.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
The equivalent of both of these are now done via macro magic when
the relevant register calls are made. The actual structure
elements will shortly go away.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Reviewed-by: Lars-Peter Clausen <lars@metafoo.de>
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
-----BEGIN PGP SIGNATURE-----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=b6g8
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.14b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
Second set of IIO new device support, features and cleanup for the 4.14 cycle.
New device support:
* ak8974
- support the AMI306.
* st_magnetometer
- add support for the LIS2MDL with bindings.
* rockchip-saradc
- add binding for rv1108 SoC (no driver change).
* srf08
- add srf02 (i2c only) and srf10 support.
* stm32-timer
- support for the STM32H7 to existing driver.
Features:
* tools
- move over to the tools buildsystem rather than hand rolling.
- add an install section to the build.
* ak8974
- use serial number to add device randomness.
- add AMI306 calibration data output.
* ccs811
- triggered buffer support.
* srf08
- add a device tree table as the old style i2c probing is going away,
- add triggered buffer support
* st32-adc
- add optional st,min-sample-time-nsecs binding to allow control of
sampling against analog circuitry.
* stm32-timer
- add output compare triggers.
* ti-ads1015
- add threshold event support.
* ti-ads7950
- Allow use on ACPI platforms including providing a default reference
voltage as there is no way to obtain this on ACPI currently.
Cleanup and fixes:
* ad7606
- fix an error return code in probe.
* ads1015
- fix incorrect data rate setting update when capture in progress,
- fix wrong scale information for the ADS1115,
- make conversions work when CONFIG_PM is not set,
- make sure we don't get a stale result after a runtime resume by
ensuring we wait long enough,
- avoid returning a false error form the buffer setup callbacks,
- add enough wait time to get the correct conversion,
- remove an unnecessary config register update,
- add a helper to set conversion mode reducing repeated boilerplate,
- use devm_iio_triggered_buffer_setup to simplify error and remove
paths,
- use iio_device_claim_direct_mode instead of opencoding the same.
* ak8974
- mark the INT_CLEAR register as precious to prevent debugfs access.
* apds9300
- constify the i2c_device_id.
* at91-sama5 adc
- add missing Kconfig dependency.
* bma180 accel
- constify the i2c_device_id.
* rockchip_saradc
- explicitly request exclusive reset control as part of the reset rework
on going throughout the kernel.
* st_accel
- fix drdy configuration for a load of accelerometers that only have
the int1 line. Fix is unimportant as presumably no deviec tree actually
used the non existent hardware line.
* st_pressure
- fix drdy configuration for LPS22HB and LPS25H by dropping int2 support
as they don't have this. Fix is unimportant as presumably no device tree
actually used the non existent hardware line.
* stm32-dac
- explicitly request exclusive reset control (part of reset being reworked).
* tsl2583
- constify the i2c_device_id.
* xadc
- coding style fixes.
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
-----BEGIN PGP SIGNATURE-----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=BApO
-----END PGP SIGNATURE-----
Merge tag 'iio-fixes-for-4.13a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-linus
Jonathan writes:
First set of IIO fixes for the 4.13 cycle.
* ad2s1210
- Fix negative angular velocity reads (identified by a gcc 7 warning)
* aspeed-adc
- Wait for initialization sequence to finish before enabling channels.
Without it no channels work.
* axp288
- Revert a patch that dropped some bogus register mods. No one is entirely
sure why but it breaks charging on some devices.
- Fix GPADC pin read returning 0. Turns out a small sleep is needed.
* bmc150
- Make sure device is restored to normal state after suspend / resume
cycle. Otherwise, simple sysfs reads are broken.
* tsl2563
- fix wrong event code.
* st-accel
- add spi 3-wire support. Needed to fix the lsm303agr accelerometer
which only had 3 wires in all cases. Side effect is to enable optional
3-wire support for other devices.
* st-pressure
- disable multiread by default for LPS22HB (only effects SPI)
* sun4i-gpadc-iio
- fix unbalanced irq enable / disable
* vf610
- Fix VALT slection for REFSEL bits - ensures we are using the
right reference pins.
Set up and use triggered buffer if there is irq defined for device in
device tree. Trigger producer triggers from rpr0521 drdy interrupt line.
Trigger consumer reads rpr0521 data to scan buffer.
Depends on previous commits of _scale and _offset.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add a link to the TCS3472 datasheet in the AMS's website.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The integration time is controlled by the ATIME register only. However,
this register is written by i2c_smbus_write_word_data() in write_raw().
We actually don't need to write a subsequent register. So just use
i2c_smbus_write_byte_data() instead.
Cc: Peter Meerwald <pmeerw@pmeerw.net>
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The TSL2563 driver provides three iio channels, two of which are raw ADC
channels (channel 0 and channel 1) in the device and the remaining one
is calculated by the two. The ADC channel 0 only supports programmable
interrupt with threshold settings and this driver supports the event but
the generated event code does not contain the corresponding iio channel
type.
This is going to change userspace ABI. Hopefully fixing this to be
what it should always have been won't break any userspace code.
Cc: Jonathan Cameron <jic23@kernel.org>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move proximity channel from last to first in structs to avoid confusion
later with buffered triggers. Proximity data output is first in rpr0521
register map.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add sysfs read/write proximity offset feature. Offset is read/write from
sensor registers. Values are proximity raw 10-bit values. After applying
offset value, output values will be (measured_raw - offset_value). Output
values are unsigned so offset value doesn't make output negative.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Just whitespace change, no functional changes.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Changed magic number to sizeof() on value read.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Refactor _set_power_state(), _resume() and _suspend().
Enable measurement only when needed, not in _init(). System can suspend
during measurement and measurement is continued on resume.
Pm turns off measurement when both ps and als measurements are disabled for
2 seconds. During off-time the power save is 20-500mA, typically 180mA.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Set sensor measurement off after probe fail in pm_runtime_set_active() or
iio_device_register(). Without this change sensor measurement stays on
even though probe fails on these calls.
This is maybe rare case, but causes constant power drain without any
benefits when it happens. Power drain is 20-500uA, typically 180uA.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Sensor was marked enabled on each call even if the call was for disabling
sensor.
Signed-off-by: Mikko Koivunen <mikko.koivunen@fi.rohmeurope.com>
Acked-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The register mapping for the IIO driver for the Liteon Light and Proximity
sensor LTR501 interrupt mode is interchanged (ALS/PS).
There is a register called INTERRUPT register (address 0x8F)
Bit 0 represents PS measurement trigger.
Bit 1 represents ALS measurement trigger.
This two bit fields are interchanged within the driver.
see datasheet page 24:
http://optoelectronics.liteon.com/upload/download/DS86-2012-0006/S_110_LTR-501ALS-01_PrelimDS_ver1%5B1%5D.pdf
Signed-off-by: Franziska Naepelt <franziska.naepelt@idt.com>
Fixes: 7ac702b314 ("iio: ltr501: Add interrupt support")
Acked-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This fixes the following warning when building with clang:
drivers/iio/light/isl29018.c:808:36: error: variable
'isl29018_acpi_match' is not needed and will not be emitted
[-Werror,-Wunneeded-internal-declaration]
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds runtime power management support to the tsl2583 driver.
The device is powered off after two seconds of inactivity. Verified that
the driver still functions correctly using a TSL2581 hooked up to a
Raspberry Pi 2.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
isl29030 is basically the same chip. The only difference
is the chip's first pin. For isl29028 its named ADDR0 and
can be used to change the chip's i2c address. For isl29030
on the other hand that pin is named Ials and is an analog
current output proportional to ALS/IR. This change is
irrelevant for the Linux driver.
This has been tested on Motorola Droid 4.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Move ISL29028 ALS / Proximity Sensor out of staging and into mainline.
Signed-off-by: Brian Masney <masneyb@onstation.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
APDS9960 can safely force runtime suspend if the system wants
to enter system-wide suspend
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
event_attrs filed of iio_info structure. As the event_attrs field of
iio_info structures is constant, so these attribute_group structures can
also be declared constant. Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.event_attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
As the attrs field of iio_info structures is also constant, so these
attribute_group structures can also be declared constant. Done manually.
File size before:
text data bss dec hex filename
5798 2376 0 8174 1fee drivers/iio/light/lm3533-als.o
File size after:
text data bss dec hex filename
5926 2248 0 8174 1fee drivers/iio/light/lm3533-als.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
attrs filed of iio_info structure. As the attrs field of iio_info
structures is constant, so these attribute_group structures can also be
declared constant.
Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
File size before:
text data bss dec hex filename
8503 488 0 8991 231f drivers/iio/light/apds9960.o
File size after:
text data bss dec hex filename
8567 424 0 8991 231f drivers/iio/light/apds9960.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Check for attribute_group structures that are only stored in the
attrs filed of iio_info structure. As the attrs field of iio_info
structures is constant, so these attribute_group structures can also be
declared constant.
Done using coccinelle:
@r1 disable optional_qualifier @
identifier i;
position p;
@@
static struct attribute_group i@p = {...};
@ok1@
identifier r1.i;
position p;
struct iio_info x;
@@
x.attrs=&i@p;
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
static
+const
struct attribute_group i={...};
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct attribute_group i;
File size before:
text data bss dec hex filename
2276 352 0 2628 a44 drivers/iio/light/bh1750.o
File size after:
text data bss dec hex filename
2340 320 0 2660 a64 drivers/iio/light/bh1750.o
Signed-off-by: simran singhal <singhalsimran0@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
This patch adds support for STMicro VL6180 - ALS, range and proximity sensor. Sensor is capable of measuring the light
intensity as well as object distance using TOF (Time of Flight) technology.
Signed-off-by: Manivannan Sadhasivam <manivannanece23@gmail.com>
Signed-off-by: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
The driver doesn't have a struct of_device_id table but supported devices
are registered via Device Trees. This is working on the assumption that a
I2C device registered via OF will always match a legacy I2C device ID and
that the MODALIAS reported will always be of the form i2c:<device>.
But this could change in the future so the correct approach is to have an
OF device ID table if the devices are registered via OF.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Add HID_USAGE_SENSOR_HUMAN_PRESENCE support for Human Presence sensitivity
parsing, in case some implementation uses it as sensitivity modifier.
Signed-off-by: Song Hongyan <hongyan.song@intel.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Handle Light and Proximity sensors presented by the ChromeOS EC Sensor hub.
Creates an IIO device for each functions.
Signed-off-by: Gwendal Grignou <gwendal@chromium.org>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
New device support:
* lsm6dsx imu
- new driver and bindings.
* max11100 adc
- new driver and bindings.
* tlc4541
- new driver
* tmp007 thermopile
- new driver.
Core
* in kernel interfaces
- pass through raw values if no scaling provided and a processed value is
requested.
* trigger
- close a race condition in acquiring trigger reference.
- constify device_type structures.
- rework the viio_trigger_alloc function to be much neater and easier to
read.
- free trigger resources correctly on some error paths. Avoids putting a
module we don't have.
Documentation
* ABI
- specify a unit for proximity measurements.
Cleanups and features
* ads1015
- constify iio_info structure.
* ads7950 cleanups following merge in previous pull
- Add device tree bindings
- Drop the ti prefix from the module name in common with other drivers.
- Change regulator name to vref to match datasheet and other drivers.
* ak8974
- remove a redundant zero timeout check.
* bmi160
- use variable names for sizeof instead of types.
* cm3605
- mark PM functions as __maybe_unused to avoid a build warning.
* isl29028 (on it's way towards moving out of staging).
- alignment fixes and newline improvements.
- combine proxim_get and read_proxim for simpler code.
- drop unused ISL29028_DEV_ATTR macro
- move some error logging into functions to cut out repitition.
- make error messages more consistent.
- tidy up some brackets.
- drop the enable flag that nothing uses.
- only set proximity rate and ALS scale when relevant channel type is enabled.
- runtime pm support.
* lsm6dsx
- fix wrong values for gyro sensitivitiy.
* mag3110
- claim direct mode during sysfs reads to avoid a race condition.
* max1363
- export OF device table IDs as module aliases.
* max30100
- use msleep for long uncritical delays.
* mcp4531
- export OF device table as module aliases.
* ms5611
- claim direct mode during sysfs reads to avoid a race condition.
* opt3001
- export OF device table as module aliases.
* sx9500
- claim direct mode during oversampling changes to avoid a race condition.
-----BEGIN PGP SIGNATURE-----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=Wvje
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.11b' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into work-next
Jonathan writes:
Second round of IIO new device support, cleanups and features for the 4.11 cycle
New device support:
* lsm6dsx imu
- new driver and bindings.
* max11100 adc
- new driver and bindings.
* tlc4541
- new driver
* tmp007 thermopile
- new driver.
Core
* in kernel interfaces
- pass through raw values if no scaling provided and a processed value is
requested.
* trigger
- close a race condition in acquiring trigger reference.
- constify device_type structures.
- rework the viio_trigger_alloc function to be much neater and easier to
read.
- free trigger resources correctly on some error paths. Avoids putting a
module we don't have.
Documentation
* ABI
- specify a unit for proximity measurements.
Cleanups and features
* ads1015
- constify iio_info structure.
* ads7950 cleanups following merge in previous pull
- Add device tree bindings
- Drop the ti prefix from the module name in common with other drivers.
- Change regulator name to vref to match datasheet and other drivers.
* ak8974
- remove a redundant zero timeout check.
* bmi160
- use variable names for sizeof instead of types.
* cm3605
- mark PM functions as __maybe_unused to avoid a build warning.
* isl29028 (on it's way towards moving out of staging).
- alignment fixes and newline improvements.
- combine proxim_get and read_proxim for simpler code.
- drop unused ISL29028_DEV_ATTR macro
- move some error logging into functions to cut out repitition.
- make error messages more consistent.
- tidy up some brackets.
- drop the enable flag that nothing uses.
- only set proximity rate and ALS scale when relevant channel type is enabled.
- runtime pm support.
* lsm6dsx
- fix wrong values for gyro sensitivitiy.
* mag3110
- claim direct mode during sysfs reads to avoid a race condition.
* max1363
- export OF device table IDs as module aliases.
* max30100
- use msleep for long uncritical delays.
* mcp4531
- export OF device table as module aliases.
* ms5611
- claim direct mode during sysfs reads to avoid a race condition.
* opt3001
- export OF device table as module aliases.
* sx9500
- claim direct mode during oversampling changes to avoid a race condition.
The I2C core always reports a MODALIAS of the form i2c:<foo> even if the
device was registered via OF, this means that exporting the OF device ID
table device aliases in the module is not needed. But in order to change
how the core reports modaliases to user-space, it's better to export it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
When CONFIG_PM_SLEEP is disabled, we get a harmless warning
drivers/iio/light/cm3605.c:292:12: error: 'cm3605_pm_resume' defined but not used [-Werror=unused-function]
drivers/iio/light/cm3605.c:281:12: error: 'cm3605_pm_suspend' defined but not used [-Werror=unused-function]
Marking the functions as possibly unused avoids the warning without
needing to add an #ifdef.
Fixes: 8afa505c12 ("iio: light: add driver for Capella CM3605")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
It's shaping to be another fairly busy cycle. Lots more on the way!
New device support
* ads7950
- new driver supporting ads7950, ads7951, ads7952, ads7953, ads7954,
ads7955, ads7956, ads7957, ads7958, ads7959, ads7960, and ads7961 ADCs.
* cm3605
- New driver for this light sensor and proximity sensor which is an
analog part with some additional digital controls.
* hx711
- New driver.
Core new stuff
* Gravity sensor type. This is a processed datastream in which the device
will try to work out which way is down.
* Split the buffer.h file into two parts. One provides the interface to 'use'
a buffer, the second provides the internals of the buffer functionality as
needed by implementations of buffers.
- Move documentation inline so as to allow use of private: tag when
generating documentation.
- Add some utility functions for the few things that are directly done
with the buffers.
- Stop exporting functions that no-one uses outside of the core code.
- Push docs down by the code in the c file where they should have always
been.
- Fix typo in kernel-doc for buffer.
- push down some includes that were previously happening implicitly.
- stop enabling the timestamp of the dummy device.
Features and cleanups
* ad5592r
- ACPI support
* ad5593r
-ACPI support.
* ad5933
- Fix a false comment about size of a particular register.
* ad7150
- replace S_IRUGO | S_IWUSR with 0644. I'm not that keen on these patches
in general, but as it was nicely presented I took this one anyway. As a
general rule will only take these as part of a larger driver cleanup.
- don't eat an error but rather reutnr it in the write_event_config callback.
* ad7606
- replace non standard range attibute with _scale
* ade7753
- use usleep_range for short sleeps
* ade7754
- use usleep_range for short sleeps
* ade7758
- use usleep_range for short sleeps
* ade7759
- use usleep_range for short sleeps
* ade7854
- use usleep_range for short sleeps
* adis16201
- fix description
* adis16203
- fix description
- fix copyright year
* adis16209
- fix description
* adt7316
- Add braces to arms of if else statement (for consistency)
- Alignment fixes.
* axp288
- Fix up an issue with accidental overwrites of data.
* bmi160
- add deivce tables for i2c and spi to support correctly identifying the
full dt name (including manufacturer).
- device tree binding.
* bmp280
- use usleep_range for short sleeps.
* cm3232
- return error from cm3232_reg_init rather than eating it if the last write
fails.
* dummy driver
- remove a semicolor found at end of a function defintition.
* exynos-adc
- use usleep_range for short sleeps.
* hid-sensor (accel)
- Add timestamp support. The hardware can provide timestamps so lets support
them. If not fall back to timestamps estimated in kernel.
* hid-sensor (light)
- Add a duplicate ID for the light channels so as to keep existing interface
whilst also using the more standard IIO interface.
* hts221
- acpi probing
* imx25-gcq
- Add a macro call to allow this driver to be automatically loaded.
* isl29028
- reorganise code to avoid deep nesting of if statements.
- move chip test and default regs into a function suitable or sharing with
power management code.
- tidy up some code alignment.
* lidar-lite-v3
- introduce compatible strings that make it clear Garmin have consideral
friends.
* mma8452
- avoid returning signed value when unsigned is appropriate
* spmi-vadc
- Update function for generic voltage conversion to take into account that
different channels on this device should be handled differently.
- Rework code to allow per channel voltage scaling and support the standard
options for this hardware.
- Fixup three minor issues with the above patches for this part. These all
effect test builds rather than the native builds for the part, but good to
clean them up anyway.
* st_sensors
- support device matching from the ACPI DST tables.
- acpi based probing for accelerometers
- acpi based probing for pressure sensors
- Allow pressure sensors to read negative values.
- Export sampling frequency for lps25h and lps331ap.
- Add support for the old DT bindings from the period when these deivces
were often supported through windows.
Docs fixup:
* typo in sysfs-bus-iio
-----BEGIN PGP SIGNATURE-----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=yjUA
-----END PGP SIGNATURE-----
Merge tag 'iio-for-4.11a' of git://git.kernel.org/pub/scm/linux/kernel/git/jic23/iio into staging-next
Jonathan writes:
First round of new device support, features and cleanups for IIO in the 4.11 cycle.
It's shaping to be another fairly busy cycle. Lots more on the way!
New device support
* ads7950
- new driver supporting ads7950, ads7951, ads7952, ads7953, ads7954,
ads7955, ads7956, ads7957, ads7958, ads7959, ads7960, and ads7961 ADCs.
* cm3605
- New driver for this light sensor and proximity sensor which is an
analog part with some additional digital controls.
* hx711
- New driver.
Core new stuff
* Gravity sensor type. This is a processed datastream in which the device
will try to work out which way is down.
* Split the buffer.h file into two parts. One provides the interface to 'use'
a buffer, the second provides the internals of the buffer functionality as
needed by implementations of buffers.
- Move documentation inline so as to allow use of private: tag when
generating documentation.
- Add some utility functions for the few things that are directly done
with the buffers.
- Stop exporting functions that no-one uses outside of the core code.
- Push docs down by the code in the c file where they should have always
been.
- Fix typo in kernel-doc for buffer.
- push down some includes that were previously happening implicitly.
- stop enabling the timestamp of the dummy device.
Features and cleanups
* ad5592r
- ACPI support
* ad5593r
-ACPI support.
* ad5933
- Fix a false comment about size of a particular register.
* ad7150
- replace S_IRUGO | S_IWUSR with 0644. I'm not that keen on these patches
in general, but as it was nicely presented I took this one anyway. As a
general rule will only take these as part of a larger driver cleanup.
- don't eat an error but rather reutnr it in the write_event_config callback.
* ad7606
- replace non standard range attibute with _scale
* ade7753
- use usleep_range for short sleeps
* ade7754
- use usleep_range for short sleeps
* ade7758
- use usleep_range for short sleeps
* ade7759
- use usleep_range for short sleeps
* ade7854
- use usleep_range for short sleeps
* adis16201
- fix description
* adis16203
- fix description
- fix copyright year
* adis16209
- fix description
* adt7316
- Add braces to arms of if else statement (for consistency)
- Alignment fixes.
* axp288
- Fix up an issue with accidental overwrites of data.
* bmi160
- add deivce tables for i2c and spi to support correctly identifying the
full dt name (including manufacturer).
- device tree binding.
* bmp280
- use usleep_range for short sleeps.
* cm3232
- return error from cm3232_reg_init rather than eating it if the last write
fails.
* dummy driver
- remove a semicolor found at end of a function defintition.
* exynos-adc
- use usleep_range for short sleeps.
* hid-sensor (accel)
- Add timestamp support. The hardware can provide timestamps so lets support
them. If not fall back to timestamps estimated in kernel.
* hid-sensor (light)
- Add a duplicate ID for the light channels so as to keep existing interface
whilst also using the more standard IIO interface.
* hts221
- acpi probing
* imx25-gcq
- Add a macro call to allow this driver to be automatically loaded.
* isl29028
- reorganise code to avoid deep nesting of if statements.
- move chip test and default regs into a function suitable or sharing with
power management code.
- tidy up some code alignment.
* lidar-lite-v3
- introduce compatible strings that make it clear Garmin have consideral
friends.
* mma8452
- avoid returning signed value when unsigned is appropriate
* spmi-vadc
- Update function for generic voltage conversion to take into account that
different channels on this device should be handled differently.
- Rework code to allow per channel voltage scaling and support the standard
options for this hardware.
- Fixup three minor issues with the above patches for this part. These all
effect test builds rather than the native builds for the part, but good to
clean them up anyway.
* st_sensors
- support device matching from the ACPI DST tables.
- acpi based probing for accelerometers
- acpi based probing for pressure sensors
- Allow pressure sensors to read negative values.
- Export sampling frequency for lps25h and lps331ap.
- Add support for the old DT bindings from the period when these deivces
were often supported through windows.
Docs fixup:
* typo in sysfs-bus-iio
According to the datasheet, the shortest available integration time for
ALS ADC conversion is 1.5625ms but illuminance_integration_time_available
sysfs file shows wrong value.
Cc: Crestez Dan Leonard <leonard.crestez@intel.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Fixes: d5d8f49b6 ("max44000: Expose ambient sensor scaling")
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <jic23@kernel.org>
Colin Ian King