events from multiple DM devices.
- Convert DM's printk macros over to using pr_<level> macros.
- Add a big-endian variant of plain64 IV to dm-crypt.
- Add support for zoned (aka SMR) devices to DM core. DM kcopyd was
also improved to provide a sequential write feature needed by zoned
devices.
- Introduce DM zoned target that provides support for host-managed zoned
devices, the result dm-zoned device acts as a drive-managed interface
to the underlying host-managed device.
- A DM raid fix to avoid using BUG() for error handling.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZXle7AAoJEMUj8QotnQNaItIH/jIhEOHV6C3YVCN34bPgypqw
6FWX3q1WQVLNaGCVC4zD6moJtW/GUoVTqCYLFVePRbcPxdDxTMLXUOgBGiuAKsl9
TS9O7xXRp9jO4ZhjxPTo8QnhxmcpOAwaLha6pQMBqfpR83+0Sp4SCG8sAUHJlw1v
etuEWHlzhTX3qrZmg0cuMnmnxiGoMmmK40BmoD603ZlhMlXFL3k9asLIfYurZoth
FpkRoihTAP9Lo4Tl9W+KOkAcXuSG/ABEPYZwrboZIkjFGIbbaJSUXwXtBK94REVG
8fNlekrX3JZ53xgmtD50WAK8RDou8G+oR2Zd6+CO90vyvEWNVhSjKUFfw8J9Q0U=
=LDjV
-----END PGP SIGNATURE-----
Merge tag 'for-4.13/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- Add the ability to use select or poll /dev/mapper/control to wait for
events from multiple DM devices.
- Convert DM's printk macros over to using pr_<level> macros.
- Add a big-endian variant of plain64 IV to dm-crypt.
- Add support for zoned (aka SMR) devices to DM core. DM kcopyd was
also improved to provide a sequential write feature needed by zoned
devices.
- Introduce DM zoned target that provides support for host-managed
zoned devices, the result dm-zoned device acts as a drive-managed
interface to the underlying host-managed device.
- A DM raid fix to avoid using BUG() for error handling.
* tag 'for-4.13/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm zoned: fix overflow when converting zone ID to sectors
dm raid: stop using BUG() in __rdev_sectors()
dm zoned: drive-managed zoned block device target
dm kcopyd: add sequential write feature
dm linear: add support for zoned block devices
dm flakey: add support for zoned block devices
dm: introduce dm_remap_zone_report()
dm: fix REQ_OP_ZONE_REPORT bio handling
dm: fix REQ_OP_ZONE_RESET bio handling
dm table: add zoned block devices validation
dm: convert DM printk macros to pr_<level> macros
dm crypt: add big-endian variant of plain64 IV
dm bio prison: use rb_entry() rather than container_of()
dm ioctl: report event number in DM_LIST_DEVICES
dm ioctl: add a new DM_DEV_ARM_POLL ioctl
dm: add basic support for using the select or poll function
Return 0 rather than BUG() if __rdev_sectors() fails and catch invalid
rdev size in the constructor.
Reported-by: Hannes Reinecke <hare@suse.de>
Cc: stable@vger.kernel.org
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When a RAID set was created on dm-raid version < 1.9.0 (old RAID
superblock format), all of the new 1.9.0 members of the superblock are
uninitialized (zero) -- including the device sectors member needed to
support shrinking.
All the other accesses to superblock fields new in 1.9.0 were reviewed
and verified to be properly guarded against invalid use. The 'sectors'
member was the only one used when the superblock version is < 1.9.
Don't access the superblock's >= 1.9.0 'sectors' member unconditionally.
Also add respective comments.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
whether blocks should migrate to/from the cache. The bio-prison-v2
interface supports this improvement by enabling direct dispatch of
work to workqueues rather than having to delay the actual work
dispatch to the DM cache core. So the dm-cache policies are much more
nimble by being able to drive IO as they see fit. One immediate
benefit from the improved latency is a cache that should be much more
adaptive to changing workloads.
- Add a new DM integrity target that emulates a block device that has
additional per-sector tags that can be used for storing integrity
information.
- Add a new authenticated encryption feature to the DM crypt target that
builds on the capabilities provided by the DM integrity target.
- Add MD interface for switching the raid4/5/6 journal mode and update
the DM raid target to use it to enable aid4/5/6 journal write-back
support.
- Switch the DM verity target over to using the asynchronous hash crypto
API (this helps work better with architectures that have access to
off-CPU algorithm providers, which should reduce CPU utilization).
- Various request-based DM and DM multipath fixes and improvements from
Bart and Christoph.
- A DM thinp target fix for a bio structure leak that occurs for each
discard IFF discard passdown is enabled.
- A fix for a possible deadlock in DM bufio and a fix to re-check the
new buffer allocation watermark in the face of competing admin changes
to the 'max_cache_size_bytes' tunable.
- A couple DM core cleanups.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZB6vtAAoJEMUj8QotnQNaoicIALuZTLElgAzxzA28cfk1+1Ea
Gd09CfJ3M6cvk/YGUU7WwiSYIwu16yOJALG4sLcYnEmUCzvKfFPcl/RpeSJHPpYM
0aVXa6NIJw7K2r3C17toiK2DRMHYw6QU843WeWI93vBW13lDJklNJL9fM7GBEOLH
NMSNw2mAq9ajtLlnJhM3ZfhloA7/u/jektvlBO1AA3RQ5Kx1cXVXFPqN7FdRfcqp
4RuEMe9faAadlXLsj3bia5IBmF/W0Qza6JilP+NLKLWB4fm7LZDjN/k+TsHWMa9e
cGR73TgUGLMBJX+sDJy8R3oeBG9JZkFVkD7I30eCjzyhSOs/54XNYQ23EkqHJU0=
=9Ryi
-----END PGP SIGNATURE-----
Merge tag 'for-4.12/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- A major update for DM cache that reduces the latency for deciding
whether blocks should migrate to/from the cache. The bio-prison-v2
interface supports this improvement by enabling direct dispatch of
work to workqueues rather than having to delay the actual work
dispatch to the DM cache core. So the dm-cache policies are much more
nimble by being able to drive IO as they see fit. One immediate
benefit from the improved latency is a cache that should be much more
adaptive to changing workloads.
- Add a new DM integrity target that emulates a block device that has
additional per-sector tags that can be used for storing integrity
information.
- Add a new authenticated encryption feature to the DM crypt target
that builds on the capabilities provided by the DM integrity target.
- Add MD interface for switching the raid4/5/6 journal mode and update
the DM raid target to use it to enable aid4/5/6 journal write-back
support.
- Switch the DM verity target over to using the asynchronous hash
crypto API (this helps work better with architectures that have
access to off-CPU algorithm providers, which should reduce CPU
utilization).
- Various request-based DM and DM multipath fixes and improvements from
Bart and Christoph.
- A DM thinp target fix for a bio structure leak that occurs for each
discard IFF discard passdown is enabled.
- A fix for a possible deadlock in DM bufio and a fix to re-check the
new buffer allocation watermark in the face of competing admin
changes to the 'max_cache_size_bytes' tunable.
- A couple DM core cleanups.
* tag 'for-4.12/dm-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (50 commits)
dm bufio: check new buffer allocation watermark every 30 seconds
dm bufio: avoid a possible ABBA deadlock
dm mpath: make it easier to detect unintended I/O request flushes
dm mpath: cleanup QUEUE_IF_NO_PATH bit manipulation by introducing assign_bit()
dm mpath: micro-optimize the hot path relative to MPATHF_QUEUE_IF_NO_PATH
dm: introduce enum dm_queue_mode to cleanup related code
dm mpath: verify __pg_init_all_paths locking assumptions at runtime
dm: verify suspend_locking assumptions at runtime
dm block manager: remove an unused argument from dm_block_manager_create()
dm rq: check blk_mq_register_dev() return value in dm_mq_init_request_queue()
dm mpath: delay requeuing while path initialization is in progress
dm mpath: avoid that path removal can trigger an infinite loop
dm mpath: split and rename activate_path() to prepare for its expanded use
dm ioctl: prevent stack leak in dm ioctl call
dm integrity: use previously calculated log2 of sectors_per_block
dm integrity: use hex2bin instead of open-coded variant
dm crypt: replace custom implementation of hex2bin()
dm crypt: remove obsolete references to per-CPU state
dm verity: switch to using asynchronous hash crypto API
dm crypt: use WQ_HIGHPRI for the IO and crypt workqueues
...
Pull block layer updates from Jens Axboe:
- Add BFQ IO scheduler under the new blk-mq scheduling framework. BFQ
was initially a fork of CFQ, but subsequently changed to implement
fairness based on B-WF2Q+, a modified variant of WF2Q. BFQ is meant
to be used on desktop type single drives, providing good fairness.
From Paolo.
- Add Kyber IO scheduler. This is a full multiqueue aware scheduler,
using a scalable token based algorithm that throttles IO based on
live completion IO stats, similary to blk-wbt. From Omar.
- A series from Jan, moving users to separately allocated backing
devices. This continues the work of separating backing device life
times, solving various problems with hot removal.
- A series of updates for lightnvm, mostly from Javier. Includes a
'pblk' target that exposes an open channel SSD as a physical block
device.
- A series of fixes and improvements for nbd from Josef.
- A series from Omar, removing queue sharing between devices on mostly
legacy drivers. This helps us clean up other bits, if we know that a
queue only has a single device backing. This has been overdue for
more than a decade.
- Fixes for the blk-stats, and improvements to unify the stats and user
windows. This both improves blk-wbt, and enables other users to
register a need to receive IO stats for a device. From Omar.
- blk-throttle improvements from Shaohua. This provides a scalable
framework for implementing scalable priotization - particularly for
blk-mq, but applicable to any type of block device. The interface is
marked experimental for now.
- Bucketized IO stats for IO polling from Stephen Bates. This improves
efficiency of polled workloads in the presence of mixed block size
IO.
- A few fixes for opal, from Scott.
- A few pulls for NVMe, including a lot of fixes for NVMe-over-fabrics.
From a variety of folks, mostly Sagi and James Smart.
- A series from Bart, improving our exposed info and capabilities from
the blk-mq debugfs support.
- A series from Christoph, cleaning up how handle WRITE_ZEROES.
- A series from Christoph, cleaning up the block layer handling of how
we track errors in a request. On top of being a nice cleanup, it also
shrinks the size of struct request a bit.
- Removal of mg_disk and hd (sorry Linus) by Christoph. The former was
never used by platforms, and the latter has outlived it's usefulness.
- Various little bug fixes and cleanups from a wide variety of folks.
* 'for-4.12/block' of git://git.kernel.dk/linux-block: (329 commits)
block: hide badblocks attribute by default
blk-mq: unify hctx delay_work and run_work
block: add kblock_mod_delayed_work_on()
blk-mq: unify hctx delayed_run_work and run_work
nbd: fix use after free on module unload
MAINTAINERS: bfq: Add Paolo as maintainer for the BFQ I/O scheduler
blk-mq-sched: alloate reserved tags out of normal pool
mtip32xx: use runtime tag to initialize command header
scsi: Implement blk_mq_ops.show_rq()
blk-mq: Add blk_mq_ops.show_rq()
blk-mq: Show operation, cmd_flags and rq_flags names
blk-mq: Make blk_flags_show() callers append a newline character
blk-mq: Move the "state" debugfs attribute one level down
blk-mq: Unregister debugfs attributes earlier
blk-mq: Only unregister hctxs for which registration succeeded
blk-mq-debugfs: Rename functions for registering and unregistering the mq directory
blk-mq: Let blk_mq_debugfs_register() look up the queue name
blk-mq: Register <dev>/queue/mq after having registered <dev>/queue
ide-pm: always pass 0 error to ide_complete_rq in ide_do_devset
ide-pm: always pass 0 error to __blk_end_request_all
..
Now that we use the proper REQ_OP_WRITE_ZEROES operation everywhere we can
kill this hack.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
Commit 63c32ed4af ("dm raid: add raid4/5/6 journaling support") added
journal support to close the raid4/5/6 "write hole" -- in terms of
writethrough caching.
Introduce a "journal_mode" feature and use the new
r5c_journal_mode_set() API to add support for switching the journal
device's cache mode between write-through (the current default) and
write-back.
NOTE: If the journal device is not layered on resilent storage and it
fails, write-through mode will cause the "write hole" to reoccur. But
if the journal fails while in write-back mode it will cause data loss
for any dirty cache entries unless resilent storage is used for the
journal.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Commit 3a1c1ef2f ("dm raid: enhance status interface and fixup
takeover/raid0") added new table line arguments and introduced an
ordering flaw. The sequence of the raid10_copies and raid10_format
raid parameters got reversed which causes lvm2 userspace to fail by
falsely assuming a changed table line.
Sequence those 2 parameters as before so that old lvm2 can function
properly with new kernels by adjusting the table line output as
documented in Documentation/device-mapper/dm-raid.txt.
Also, add missing version 1.10.1 highlight to the documention.
Fixes: 3a1c1ef2f ("dm raid: enhance status interface and fixup takeover/raid0")
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This version bump reflects that the reshape corruption fix (commit
92a39f6cc "dm raid: fix data corruption on reshape request") is
present.
Done as a separate fix because the above referenced commit is marked for
stable and target version bumps in a stable@ fix are a recipe for the
fix to never get backported to stable@ kernels (because of target
version number conflicts).
Also, move RESUME_STAY_FROZEN_FLAGS up with the reset the the _FLAGS
definitions now that we don't need to worry about stable@ conflicts as a
result of missing context.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The lvm2 sequence to manage dm-raid constructor flags that trigger a
rebuild or a reshape is defined as:
1) load table with flags (e.g. rebuild/delta_disks/data_offset)
2) clear out the flags in lvm2 metadata
3) store the lvm2 metadata, reload the table to reset the flags
previously established during the initial load (1) -- in order to
prevent repeatedly requesting a rebuild or a reshape on activation
Currently, loading an inactive table with rebuild/reshape flags
specified will cause dm-raid to rebuild/reshape on resume and thus start
updating the raid metadata (about the progress). When the second table
reload, to reset the flags, occurs the constructor accesses the volatile
progress state kept in the raid superblocks. Because the active mapping
is still processing the rebuild/reshape, that position will be stale by
the time the device is resumed.
In the reshape case, this causes data corruption by processing already
reshaped stripes again. In the rebuild case, it does _not_ cause data
corruption but instead involves superfluous rebuilds.
Fix by keeping the raid set frozen during the first resume and then
allow the rebuild/reshape during the second resume.
Fixes: 9dbd1aa3a ("dm raid: add reshaping support to the target")
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 4.8+
While cleaning up awkward branching in raid_message() a raid set "check"
regression was introduced because "check" needs both MD_RECOVERY_SYNC
and MD_RECOVERY_REQUESTED flags set.
Fix this regression by explicitly setting both flags for the "check"
case (like is also done for the "repair" case, but redundant set_bit()s
are perfectly fine because it adds clarity to what is needed in response
to both messages -- in addition this isn't fast path code).
Fixes: 105db59912 ("dm raid: cleanup awkward branching in raid_message() option processing")
Reported-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
For consistency, call read_disk_sb() from
attempt_restore_of_faulty_devices() instead
of calling sync_page_io() directly.
Explicitly set device to faulty on superblock read error.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add md raid4/5/6 journaling support (upstream commit bac624f3f8 started
the implementation) which closes the write hole (i.e. non-atomic updates
to stripes) using a dedicated journal device.
Background:
raid4/5/6 stripes hold N data payloads per stripe plus one parity raid4/5
or two raid6 P/Q syndrome payloads in an in-memory stripe cache.
Parity or P/Q syndromes used to recover any data payloads in case of a disk
failure are calculated from the N data payloads and need to be updated on the
different component devices of the raid device. Those are non-atomic,
persistent updates. Hence a crash can cause failure to update all stripe
payloads persistently and thus cause data loss during stripe recovery.
This problem gets addressed by writing whole stripe cache entries (together with
journal metadata) to a persistent journal entry on a dedicated journal device.
Only if that journal entry is written successfully, the stripe cache entry is
updated on the component devices of the raid device (i.e. writethrough type).
In case of a crash, the entry can be recovered from the journal and be written
again thus ensuring consistent stripe payload suitable to data recovery.
Future dependencies:
once writeback caching being worked on to compensate for the throughput
implictions involved with writethrough overhead is supported with journaling
in upstream, an additional patch based on this one will support it in dm-raid.
Journal resilience related remarks:
because stripes are recovered from the journal in case of a crash, the
journal device better be resilient. Resilience becomes mandatory with
future writeback support, because loosing the working set in the log
means data loss as oposed to writethrough, were the loss of the
journal device 'only' reintroduces the write hole.
Fix comment on data offsets in parse_dev_params() and initialize
new_data_offset as well.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
During raid set resize checks and setting up the recovery offset in case a raid
set grows, calculated rd->md.dev_sectors is compared to rs->dev[0].rdev.sectors.
Device 0 may not be defined in case userspace passes in '- -' for it
(lvm2 doesn't do that so far), thus it's device sectors can't be taken
authoritatively in this comparison and another valid device must be used
to retrieve the device size.
Use mddev->dev_sectors in checking for ongoing recovery for the same reason.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
This fix addresses the following 3 failure scenarios:
1) If a (transiently) inaccessible metadata device is being passed into the
constructor (e.g. a device tuple '254:4 254:5'), it is processed as if
'- -' was given. This erroneously results in a status table line containing
'- -', which mistakenly differs from what has been passed in. As a result,
userspace libdevmapper puts the device tuple seperate from the RAID device
thus not processing the dependencies properly.
2) False health status char 'A' instead of 'D' is emitted on the status
status info line for the meta/data device tuple in this metadata device
failure case.
3) If the metadata device is accessible when passed into the constructor
but the data device (partially) isn't, that leg may be set faulty by the
raid personality on access to the (partially) unavailable leg. Restore
tried in a second raid device resume on such failed leg (status char 'D')
fails after the (partial) leg returned.
Fixes for aforementioned failure scenarios:
- don't release passed in devices in the constructor thus allowing the
status table line to e.g. contain '254:4 254:5' rather than '- -'
- emit device status char 'D' rather than 'A' for the device tuple
with the failed metadata device on the status info line
- when attempting to restore faulty devices in a second resume, allow the
device hot remove function to succeed by setting the device to not in-sync
In case userspace intentionally passes '- -' into the constructor to avoid that
device tuple (e.g. to split off a raid1 leg temporarily for later re-addition),
the status table line will correctly show '- -' and the status info line will
provide a '-' device health character for the non-defined device tuple.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
. some locking improvements in DM bufio
. add Kconfig option to disable the DM block manager's extra locking
which mainly serves as a developer tool
. a few bug fixes to DM's persistent-data
. a couple changes to prepare for multipage biovec support in the block
layer
. various improvements and cleanups in the DM core, DM cache, DM raid
and DM crypt
. add ability to have DM crypt use keys from the kernel key retention
service
. add a new "error_writes" feature to the DM flakey target, reads are
left unchanged in this mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJYUW8zAAoJEMUj8QotnQNaAWEIAMRQ4aCXq5T7F9Hf4K/l6FwO
FoBr2TPS3Lf0vm/A5Tr819I47hk7q0oroa61ARbpS90iuGt/Au/Sk35cn1BwT0YW
llMvMGbh+w9ZBUJGkyexdXbyfm5ywPHuthMr4CK/UNASyjDl2QMAeBuUZ6FLSPn1
RUL/RYv0mG/7EXOPz0PURPb5rpjO15cAU0NjfNS0862UVR8x8dNS6iImOmScsioe
Flw90qPl3kMBxBHik8xSPJfhtW+lD7xSaOlWzHKtalnUZHRG2BNUtlAMKdiaynx2
yl9MhSsi8wlgd4h9WmlmaOr0VqkU5UYY9D9TDuuJwXnHUXGenVSJ/aGOohr+bm4=
=kOoK
-----END PGP SIGNATURE-----
Merge tag 'dm-4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- various fixes and improvements to request-based DM and DM multipath
- some locking improvements in DM bufio
- add Kconfig option to disable the DM block manager's extra locking
which mainly serves as a developer tool
- a few bug fixes to DM's persistent-data
- a couple changes to prepare for multipage biovec support in the block
layer
- various improvements and cleanups in the DM core, DM cache, DM raid
and DM crypt
- add ability to have DM crypt use keys from the kernel key retention
service
- add a new "error_writes" feature to the DM flakey target, reads are
left unchanged in this mode
* tag 'dm-4.10-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (40 commits)
dm flakey: introduce "error_writes" feature
dm cache policy smq: use hash_32() instead of hash_32_generic()
dm crypt: reject key strings containing whitespace chars
dm space map: always set ev if sm_ll_mutate() succeeds
dm space map metadata: skip useless memcpy in metadata_ll_init_index()
dm space map metadata: fix 'struct sm_metadata' leak on failed create
Documentation: dm raid: define data_offset status field
dm raid: fix discard support regression
dm raid: don't allow "write behind" with raid4/5/6
dm mpath: use hw_handler_params if attached hw_handler is same as requested
dm crypt: add ability to use keys from the kernel key retention service
dm array: remove a dead assignment in populate_ablock_with_values()
dm ioctl: use offsetof() instead of open-coding it
dm rq: simplify use_blk_mq initialization
dm: use blk_set_queue_dying() in __dm_destroy()
dm bufio: drop the lock when doing GFP_NOIO allocation
dm bufio: don't take the lock in dm_bufio_shrink_count
dm bufio: avoid sleeping while holding the dm_bufio lock
dm table: simplify dm_table_determine_type()
dm table: an 'all_blk_mq' table must be loaded for a blk-mq DM device
...
The mddev->flags are used for different purposes. There are a lot of
places we check/change the flags without masking unrelated flags, we
could check/change unrelated flags. These usage are most for superblock
write, so spearate superblock related flags. This should make the code
clearer and also fix real bugs.
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Shaohua Li <shli@fb.com>
Commit ecbfb9f118 ("dm raid: add raid level takeover support") moved the
configure_discard_support() call from raid_ctr() to raid_preresume().
Enabling/disabling discard _must_ happen during table load (through the
.ctr hook). Fix this regression by moving the
configure_discard_support() call back to raid_ctr().
Fixes: ecbfb9f118 ("dm raid: add raid level takeover support")
Cc: stable@vger.kernel.org # 4.8+
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Remove CTR_FLAG_MAX_WRITE_BEHIND from raid4/5/6's valid ctr flags.
Only the md raid1 personality supports setting a maximum number
of "write behind" write IOs on any legs set to "write mostly".
"write mostly" enhances throughput with slow links/disks.
Technically the "write behind" value is a write intent bitmap
property only being respected by the raid1 personality. It allows a
maximum number of "write behind" writes to any "write mostly" raid1
mirror legs to be delayed and avoids reads from such legs.
No other MD personalities supported via dm-raid make use of "write
behind", thus setting this property is superfluous; it wouldn't cause
harm but it is correct to reject it.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When target 1.9.1 gets takeover/reshape requests on devices with old superblock
format not supporting such conversions and rejects them in super_init_validation(),
it logs bogus error message (e.g. Reshape when a takeover is requested).
Whilst on it, add messages for disk adding/removing and stripe sectors
reshape requests, use the newer rs_{takeover,reshape}_requested() API,
address a raid10 false positive in checking array positions and
remove rs_set_new() because device members are already set proper.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
dm-raid 1.9.0 fails to activate existing RAID4/10 devices that have the
old superblock format (which does not have takeover/reshaping support
that was added via commit 33e53f0685).
Fix validation path for old superblocks by reverting to the old raid4
layout and basing checks on mddev->new_{level,layout,...} members in
super_init_validation().
Cc: stable@vger.kernel.org # 4.8
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
In ecbfb9f118 ("dm raid: add raid level takeover support") a new
compatible feature flag was added. Validation for these compat_features
was added but this only passes for new raid mappings with this feature
flag. This causes previously created raid mappings to be failed at
import.
Check compat_features for the only valid combination.
Fixes: ecbfb9f118 ("dm raid: add raid level takeover support")
Cc: stable@vger.kernel.org # v4.8
Signed-off-by: Andy Whitcroft <apw@canonical.com>
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
The raid0 MD personality does not start a raid0 array with any of its
data devices missing.
dm-raid was removing data/metadata device pairs unconditionally if it
failed to read a superblock off the respective metadata device of such
pair, resulting in failure to start arrays with the raid0 personality.
Avoid removing any data/metadata device pairs in case of raid0
(e.g. lvm2 segment type 'raid0_meta') thus allowing MD to start the
array.
Also, avoid region size validation for raid0.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
attempt_restore_of_faulty_devices() is limited to 64 when it should support
the new maximum of 253 when identifying any failed devices. It clears any
revivable devices via an MD personality hot remove and add cylce to allow
for their recovery.
Address by using existing functions to retrieve and update all failed
devices' bitfield members in the dm raid superblocks on all RAID devices
and check for any devices to clear in it.
Whilst on it, don't call attempt_restore_of_faulty_devices() for any MD
personality not providing disk hot add/remove methods (i.e. raid0 now),
because such personalities don't support reviving of failed disks.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
'lvchange --refresh RaidLV' causes a mapped device suspend/resume cycle
aiming at device restore and resync after transient device failures. This
failed because flag RT_FLAG_RS_RESUMED was always cleared in the suspend path,
thus the device restore wasn't performed in the resume path.
Solve by removing RT_FLAG_RS_RESUMED from the suspend path and resume
unconditionally. Also, remove superfluous comment from raid_resume().
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
On LVM2 conversions via lvconvert(8), the target keeps mapped devices in
frozen state when requesting RAID devices be resynchronized. This
applies to e.g. adding legs to a raid1 device or taking over from raid0
to raid4 when the rebuild flag's set on the new raid1 legs or the added
dedicated parity stripe.
Also, fix frozen recovery for reshaping as well.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
During a resynchronization, device status char 'a' is output on the raid
status line for every device of a RAID set. It changes from 'a' to 'A'
(unless device failure) when the resynchronization completes.
Interrupting and restarting a resynchronization, by reloading the DM
table, erroneously lead to status char 'A'.
Fix this by avoiding setting the MD_RECOVERY_REQUESTED flag in
raid_preresume().
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
When lvm2 userspace requests a RaidLV repair, it sets the rebuild
constructor flag on the new replacement DataLVs but does not clear the
respective MetaLVs. Hence the superblock that is loaded from such new
MetaLVs may have a non-zero incompat_features member and the constructor
will fail with false-positive on incompat_features.
Solve by initializing the incompat_features member properly.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
__CTR_FLAG_MIN_RECOVERY_RATE was used instead of __CTR_FLAG_MAX_RECOVERY_RATE
thus causing max_recovery_rate to be rejected in case min_recovery_rate
was already set.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
raid_io_hints() was retrieving the number of data stripes used for the
calculation of io_opt from struct r5conf, which is not defined for raid0
mappings.
Base the calculation on the in-core raid_set structure instead.
Also, adjust to use to_bytes() for the sector -> bytes conversion
throughout.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Use 'unsigned int' where appropriate.
Return negative errors.
Correct an indentation.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add "delta_disks" constructor argument support to raid1 to allow for
consistent userspace disk addition/removal handling.
Fix raid_status() to report all raid disks with status and table output
on disk adding reshapes, not just the ones listed on the mddev; optimize
its rebuild and writemostly output.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Enhance rs_reshape_requested() check function to be more transparent and
fix its raid10 check.
Streamline the constructor by factoring out reshaping preparation into
fucntion rs_prepare_reshape().
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Resizing a RAID set during recovery can be allowed, because the MD
resynchronization thread will either stop any ongoing recovery in case
of shrinking below the current recovery position or carry on recovery
to the new size if the set is growing.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Add function rs_setup_recovery() to allow for defined setup of RAID set
recovery in the constructor.
Will be called with dev_sectors={0, rdev->sectors, MaxSectors} to
recover a new or enforced sync, grown or not to be synhronized RAID set
respectively.
Prevents recovery on raid0, which doesn't support it.
Enforces recovery on raid6 to ensure properly defined Syndromes
mandatory for that MD personality are being created.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Linus Torvalds