commit 85ff3c29d7 ("ASoC: samsung: Rename DMA platform registration
functions") renames the DMA registration functions. Fix the places where
it was left out.
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
We have to disable the ssi irq, as it is not safe for all platforms to
write back into the status register. It also runs into non-linefetch
aborts.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
imx-pcm-fiq is checking for TE RE bits, so enable them only if
necessary.
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The chip errata for the i.MX35, Rev.2 has the following errata:
ENGcm06222: SSI:Transmission does not take place in bit length early frame sync
configuration
The workaround states, that TX_EN and SSI_EN bits should be set in the same
register write. As the next errata in the document (ENGcm06532) says to always
write RX_EN and TX_EN in the same register write in network mode.
Therefore include the whole write to
CCSR_SSI_SCR_TE and CCSR_SSI_SCR_RE
into the write to
CCSR_SSI_SCR_SSIEN
Signed-off-by: Steffen Trumtrar <s.trumtrar@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds ac97-slave support.
For ac97, the registers have to be setup earlier than for other ssi
modes because there is some communication with the external device
before streaming. So this patch introduces a fsl_ssi_setup function to
setup the registers for different ssi operation modes seperately.
This patch was tested with imx27-pca100.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fixing warning message:
sound/pci/rme96.c: In function ‘snd_rme96_resume’:
sound/pci/rme96.c:2418:19: warning: ignoring return value of ‘pci_enable_device’, declared with attribute warn_unused_result [-Wunused-result]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The headphone automute on this machine triggers annoying pop noises.
It seems that only the first DAC can be used, the secondary DAC always
results in this problem. This patch disables the secondary DAC with
a few additional workarounds.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fixed ALC283 D3 to D0 and D0 to D3 Headphone pop noise.
The previous fix [c5177c86: ALSA: hda - Fix the noise after suspend on
ALC283 codec] doesn't work sufficiently for some laptops.
Signed-off-by: Kailang Yang <kailang@realtek.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Without proper power management handling, the first use
of a Digi96/8 anytime after a suspend / resume cycle will
start playback with distortions.
v3: Abort if vmalloc() of suspend buffers fail, but do not
leak memory in that case.
[fixed wrong memory leak fix again -- tiwai]
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This patch implements a device-tree-only CPU DAI driver for Freescale
S/PDIF controller that supports stereo playback and record feature.
Signed-off-by: Nicolin Chen <b42378@freescale.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unneeded error handling on the result of a call to
platform_get_resource_byname when the value is passed to devm_ioremap_resource.
In the case of omap-dmic.c, the error-handling code of
devm_ioremap_resource is also corrected to include releasing the clock.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,e,e1;
expression ret != 0;
identifier l;
@@
res = platform_get_resource_byname(...);
- if (res == NULL) { ... \(goto l;\|return ret;\) }
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In fsl_ssi_remove() we need to remove the resources in the opposite order that
they were acquired in probe.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds generic ac97 reset functions using pincontrol and gpio
parsed from devicetree.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The current naming with a simple asoc_ prefix is too generic for use in
multiplatform kernels.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
This patch doesn't change functionality, it only improves readability
and fixes a copy&paste error in a comment.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use enum hdspm_ltc_format's fps_30 (corresponds to 4) instead of 30,
Other case branches return 1, 2 or 3 respectively, so 30 obviously is
wrong.
Since SNDRV_HDSPM_IOCTL_GET_LTC had never been working due to a
copy&paste error in hdspm.h, this change doesn't break userspace.
Signed-off-by: Adrian Knoth <adi@drcomp.erfurt.thur.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Yet another entry, just use the existing fixup for this machine, too.
Reported-by: "Nathanael D. Noblet" <nathanael@gnat.ca>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
If compiled without CONFIG_SND_HDA_I915, the audio driver cannot
request power well. However, if the power well is on for other
reasons, maybe audio can still work. Therefore, do not skip the
card completely if compiled without CONFIG_SND_HDA_I915.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The higher mic boosts (on internal mic) are so noisy they're unusable
in practice.
BugLink: https://bugs.launchpad.net/bugs/1213820
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Provide a common compatible string for device trees to list as a fallback
for simplicity. We don't currently have a binding document but let's not
fix that right now...
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to make the device easier to hook up to external components in
system designs and ensure operation when DAPM support becomes mandatory
add DAPM support.
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to make the device easier to hook up to external components in
system designs and ensure operation when DAPM support becomes mandatory
add DAPM support.
Signed-off-by: Mark Brown <broonie@linaro.org>
This makes it possible to hook the device into a more complex board and
ensures it will continue to work with non-DAPM support removed from the
core.
Signed-off-by: Mark Brown <broonie@linaro.org>
In order to ensure that the device continues to work with DAPM support
being mandatory provide stub DAPM widgets and routes.
Note that the public information on the device appears to make no
mention of the FM support the driver appears to have.
Signed-off-by: Mark Brown <broonie@linaro.org>
Make it possible to connect external devices to the CODEC and ensure
continued operation with non-DAPM support removed from the core.
Signed-off-by: Mark Brown <broonie@linaro.org>
We don't set the GPIO values from atomic context so support GPIOs that
can't be controlled from atomic context.
Signed-off-by: Mark Brown <broonie@linaro.org>
Bit 9 of PLL2,3 and 4 is reserved as '0'. The 24bit fractional part
should be split across each register in 8bit chunks.
Signed-off-by: Mike Dyer <mike.dyer@md-soft.co.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
SND_SOC_FSL_UTILS is only used by PowerPC machines, so let's drop it in the
i.mx case.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This ensures the driver continues to work with DAPM mandatory and makes
it easier to connect the device up to other components in the subsystem.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Move tea575x from sound/i2c/other to drivers/media/radio
Includes Kconfig changes by Hans Verkuil.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Move include/sound/tea575x-tuner.h to include/media/tea575x.h and update files that include it.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Acked-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
This just cleans up the table, no functional changes.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The internal mic boost is so noisy on boosts 2 and 3 so they are
unusable in practice.
BugLink: https://bugs.launchpad.net/bugs/1213055
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Provide external widgets for the CODEC to ensure the device continues to
function with DAPM mandatory and to make it easier to hook the device up
to other components.
Signed-off-by: Mark Brown <broonie@linaro.org>
Use the core to do I/O rather than directly calling the driver operations
in order to support further refactoring.
Signed-off-by: Mark Brown <broonie@linaro.org>
Move imx-audmux macro definitions to include/dt-bindings, so they can be
used for devicetree.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Gateway LT27 needs a fixup for the inverted digital mic.
Reported-by: "Nathanael D. Noblet" <nathanael@gnat.ca>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A few driver specific fixes here plus one core fix for a memory
corruption issue in DAPM initialisation which could lead to crashes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.14 (GNU/Linux)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=WWSS
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.11-rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.11
A few driver specific fixes here plus one core fix for a memory
corruption issue in DAPM initialisation which could lead to crashes.
When users of SND_DMAENGINE_PCM are built as module, the config symbol
SND_DMAENGINE_PCM must be tristate, otherwise the linker will fail.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Provide DAPM for the device, ensuring operation with DAPM required by the
core and making it easier to hook up external hardware to it.
Signed-off-by: Mark Brown <broonie@linaro.org>
Provide DAPM for the device, ensuring operation with DAPM required by the
core and making it easier to hook up external hardware to it.
Signed-off-by: Mark Brown <broonie@linaro.org>
The bindings do not carry any resources, as the module only registers
the ASoC platform driver.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
With the new dmaengine implementation, the filter_data parameter has
to be set earlier, from pxa_ssp_startup().
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Use snd_dmaengine_dai_dma_data for passing the dma parameters from
clients to the pxa pcm lib. This does no functional change, it's just an
intermedia step to migrate the pxa bits over to dmaengine.
The calculation of dcmd is a transition hack which will be removed again
in a later patch. It's just there to make the transition more readable.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mark Brown <broonie@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
The pxa ssp DAI acts as a user of a pxa ssp port, and needs an
appropriate 'port' phandle in DT to reference the upstream.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
For the PXA DMA rework, we need the generic dmaengine implementation
that currently lives in sound/soc for standalone (non-ASoC) AC'97
support.
Move it to sound/core, and rename the Kconfig symbol.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add a Mic Jack widget to the Tegra+RT5640 machine driver, and document
this in the DT binding. This enables the DT to include the Mic Jack in
the audio routing table, and hence enables capture of audio, in addition
to the previously-working playback.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The Tegra30 I2S driver was writing the AHUB interface parameters to the
playback path register rather than the capture path register. This
caused the capture parameters not to be configured at all, so if
capturing using non-HW-default parameters (e.g. 16-bit stereo rather
than 8-bit mono) the audio would be corrupted.
With this fixed, audio capture from an analog microphone works correctly
on the Cardhu board.
Cc: stable@vger.kernel.org
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Remove unneeded error handling on the result of a call to
platform_get_resource when the value is passed to devm_ioremap_resource.
Move the call to platform_get_resource adjacent to the call to
devm_ioremap_resource to make the connection between them more clear.
A simplified version of the semantic patch that makes this change is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression pdev,res,n,e,e1;
expression ret != 0;
identifier l;
@@
- res = platform_get_resource(pdev, IORESOURCE_MEM, n);
... when != res
- if (res == NULL) { ... \(goto l;\|return ret;\) }
... when != res
+ res = platform_get_resource(pdev, IORESOURCE_MEM, n);
e = devm_ioremap_resource(e1, res);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
The hardware does support synchronized start/pause/stop of pcm streams,
so there is no reason not to add that feature after more than ten years.
Some minor coding style / white space fixes in the surroundings of the
changes.
Signed-off-by: Knut Petersen <Knut_Petersen@t-online.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Exynos5420 added support for I2S TDM mode. For this, there are some
register changes in the I2S controller. This patch adds the relevant
register changes to support I2S in normal mode. This patch adds a
quirk for TDM mode and if TDM mode is present all the relevent changes
will be applied.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Samsung has different versions of I2S introduced in different
platforms. Each version has some new support added for multichannel,
secondary fifo, s/w reset control and internal mux for rclk src clk.
Each newly added change has a quirk. So this patch adds all the
required quirks as driver data and based on compatible string from
dtsi fetches the quirks.
Signed-off-by: Padmavathi Venna <padma.v@samsung.com>
Reviewed-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This does not fully map the power control available within the device
but it provides the hooks for routing signals through the device and
allows automatic management of the device low power mode.
Signed-off-by: Mark Brown <broonie@linaro.org>
This makes it possible to hook the device into a more complex board and
ensures it will continue to work with non-DAPM support removed from the
core.
Signed-off-by: Mark Brown <broonie@linaro.org>
The wm8997 is a compact, high-performance audio hub CODEC with SLIMbus
interfacing, for smartphones, tablets and other portable audio devices
based on the Arizona platform.
This patch adds the wm8997 CODEC driver.
[Fixed some interface churn from bitrot due to the patch not going via
the MFD tree as expected -- broonie]
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Ensure that the recently added path kcontrol list is initialised otherwise
we may crash trying to delete routes that don't have kcontrols.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Attempting to create the route as part of adding a mux control causes us
to attempt to add the same route twice since we loop over all sources
for the mux after creating the control. Instead do the addition in the
callers.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
The current generic parser code assumes that always a pin widget
controls the mute for an output blindly although it might be a
different widget in the middle. Instead of the fixed assumption,
check each parsed path and just pick up the right widget that has been
already defined as a mute control.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The auto-mute using the amp currently works only for a single amp on a
pin. Make it working also with HDA_CTL_BIND_MUTE type, too.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add the volume control quirk for avoiding the kernel warning
for the Logitech HD Webcam C525
as in the similar commit 36691e1be6
for the Logitech HD Webcam C310.
Reported-by: Maksim Boyko <maksim.a.boyko@gmail.com>
Tested-by: Maksim Boyko <maksim.a.boyko@gmail.com>
Cc: <stable@vger.kernel.org> # 3.10.5+
Signed-off-by: Maksim Boyko <maksim.a.boyko@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The routes linking the widget and the input mux were being added
manually, rather than by the ARIZONA_MUX_ROUTES macro. This patchs adds
the routes to the macro.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This makes it possible to hook the device into a more complex board and
ensures it will continue to work with non-DAPM support removed from the
core.
Signed-off-by: Mark Brown <broonie@linaro.org>
Saves some code. We should also be able to manage the power up and reset
registers using DAPM but it's probably more trouble than it's worth in
mains powered systems.
Signed-off-by: Mark Brown <broonie@linaro.org>
This makes it easer to integrate the device with other on-board components
and ensures correct operation following removal of support for non-DAPM
CODECs.
Signed-off-by: Mark Brown <broonie@linaro.org>
The GPIO manipulation done by this driver is never in atomic context so
we can use gpio_set_value_cansleep() and support GPIOs that can't be set
from atomic context.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
There is no need for the power down work to be done on a per CPU workqueue
especially considering the fairly long delay before powerdown.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Vinod Koul <vinod.koul@intel.com>
We've added a fake mute control (setting the amp volume to zero) for
CX5051 at commit [3868137e: ALSA: hda - Add a fake mute feature], but
this feature was overlooked in the generic parser implementation. Now
the driver lacks of mute controls on these codecs.
The fix is just to check both AC_AMPCAP_MUTE and AC_AMPCAP_MIN_MUTE
bits in each place checking the amp capabilities.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=59001
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit aafe77cc45 (ALSA: usb-audio: add support for many Roland/Yamaha
devices) had several logic errors that prevented create_auto_midi_quirk
from enumerating any MIDI ports.
Reported-by: Keith A. Milner <maillist@superlative.org>
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Patch makes pcm buffers DMA-able by allocating each one separately.
Signed-off-by: Torsten Schenk <torsten.schenk@zoho.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Correct the pins for a line-in and a headphone on LG LW25 laptop with
ALC880 codec. Other pins seem fine.
Reported-and-tested-by: Joonas Saarinen <jonskunator@gmail.com>
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Replace ARRAY_AND_SIZE(e) in function argument position to avoid hiding the
arity of the called function.
The semantic match that makes this change is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@@
expression e,f;
@@
f(...,
- ARRAY_AND_SIZE(e)
+ e,ARRAY_SIZE(e)
,...)
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Mark Brown <broonie@linaro.org>
This makes it possible to hook the device into a more complex board and
ensures it will continue to work with non-DAPM support removed from the
core.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Alexander Sverdlin <subaparts@yandex.ru>
This makes it possible to hook the device into a more complex board and
ensures it will continue to work with non-DAPM support removed from the
core.
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_info_enum_ext() and snd_soc_info_enum_double() are almost identical. The
only difference is that snd_soc_info_enum_double() is also able to handle stereo
controls. Using snd_soc_info_enum double() instead of snd_soc_info_enum_ext()
for the SOC_ENUM_EXT control's info callback allows us to remove
snd_soc_info_enum_ext().
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SOC_SINGLE_EXT control has been using snd_soc_info_volsw() for its info
callback since commit 1c433fb ("[ALSA] soc - 0.13 ASoC headers"). The
snd_soc_info_volsw_ext() function has been unused ever since then, so remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The soc_pm_waitq waitqueue has been around as long as the ASoC framework
existed, but has never been used so far, so remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
We don't actually use the "go" variable so it can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
__initdata should be placed between the variable name and equal
sign for the variable to be placed in the intended section.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
This makes it possible to hook up other devices in boards and is required
by removal of support for non-DAPM CODECs in the core.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
There is no need to pass constants via stack. The width may be explicitly
specified in the format.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The driver used to assume that the streaming endpoint's wMaxPacketSize
value would be an indication of how much data the endpoint expects or
sends, and compute the number of packets per URB using this value.
However, the Focusrite Scarlett 2i4 declares a value of 1024 bytes,
while only about 88 or 44 bytes are be actually used. This discrepancy
would result in URBs with far too few packets, which would not work
correctly on the EHCI driver.
To get correct URBs, use wMaxPacketSize only as an upper limit on the
packet size.
Reported-by: James Stone <jamesmstone@gmail.com>
Tested-by: James Stone <jamesmstone@gmail.com>
Cc: <stable@vger.kernel.org> # 2.6.35+
Signed-off-by: Clemens Ladisch <clemens@ladisch.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This makes it easier to hook into boards and ensures the driver continues
to work with support for non-DAPM CODECs removed.
Signed-off-by: Mark Brown <broonie@linaro.org>
Patch fixes 6fire not to use stack as URB transfer_buffer. URB buffers need to
be DMA-able, which stack is not. Furthermore, transfer_buffer should not be
allocated as part of larger device structure because DMA coherency issues and
patch fixes this issue too.
Cc: stable@vger.kernel.org
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@iki.fi>
Tested-by: Torsten Schenk <torsten.schenk@zoho.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since non-DAPM devices are not going to be supported provide DAPM input
and output widgets and hook them up to the DAIs.
Signed-off-by: Mark Brown <broonie@linaro.org>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Commit 02502da45 (ASoC: imx-mc13783: Depend on ARCH_ARM) introduced 'ARCH_ARM'
as a dependency for SND_SOC_IMX_MC13783, but this is a non-existent symbol.
This makes the selection of SND_SOC_IMX_MC13783 to be impossible.
Use the correct 'ARM' symbol instead.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Beep Volume Min/Max was backwards.
Change to SOC_SONGLE_SX_TLV for correct volume representation
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@kernel.org
Description of the Asoc machine driver for an at91sam9x5 based board
with a wm8731 audio DAC. Wm8731 is clocked by a crystal and used as a
master on the SSC/I2S interface. Its connections are a headphone jack
and an Line input jack.
[Richard: this is based on an old patch from Nicolas that I forward
ported and reworked to use only device tree]
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
There may be some platforms using fsl-ssi that do not have a DMA driver
with generic DMA bindings. So this patch adds support for the generic
DMA bindings, while still accepting the old "fsl,dma-events" property if
"dmas" is not found.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add support for non-dma pcm for imx platforms with imx-pcm-fiq support.
Instead of imx-pcm-audio, in this case imx-pcm-fiq-audio device is added
and the SIER flags are set differently.
We need imx-pcm-fiq for some boards that use an incompatible codec.
imx-pcm-fiq handles those codecs differently and allows to operate with
them. DMA is not possible because some data sent by the codecs, e.g.
wm9712, is not in the datastream. Also some data is mixed up in the
fifos, so that we need to sort them out manually.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Mark Brown <broonie@linaro.org>
Adds a function to parse a default port configuration from devicetree.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch cleanups empty functions on scu
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds BUSIF support for R-Car sound DMAEngine transfer.
The sound data will be transferred via FIFO which can cover blank time
which will happen when DMA channel is switching.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds DMAEngine transfer on SSI.
But, it transfers sound data from memory to SSI directly
without using HPBIF at this time.
It will be updated soon
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
R-Car Sound driver will support DMA transfer in the future,
then, SSI/SRU/SRC will use it.
Current R-Car can't use soc-dmaengine-pcm.c since its DMAEngine
doesn't support dmaengine_prep_dma_cyclic(),
and SSI needs double plane transfer (which needs special submit) on DMAC.
This patch adds common DMAEngine method for it
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Current rsnd driver is using struct rsnd_dai_platform_info
so that indicate sound DAI information (playback/capture SSI ID).
But, SSI settings were also required separately.
Thus, platform settings was very un-understandable.
This patch adds dai_id to SSI
settings, and removed rsnd_dai_platform_info.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
The input OSR bits are specified differently for wm5110 than for current
revs of wm5102. This patch corrects support for this on wm5110.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It is unused and a leftover of the pre multi-component era.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
It is unused and a leftover of the pre multi-component era.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The tlv320aic26 contains a embedded snd_soc_codec struct which is referenced in
the keyclick code. That struct is never initialized though, replace the embedded
struct with a pointer and use that in the keyclick code.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Commit 6e0650 (ASoC: wm8994: Use SOC_SINGLE_EXT() instead of open-coding
it) went too far and converted a DAPM control to use SOC_SINGLE_EXT()
which crashes. Revert that portion of the patch.
Signed-off-by: Mark Brown <broonie@linaro.org>
Prevent NULL dereference in snd_usb_add_endpoints(), when
alts is passed as NULL. In this case, WARN (since this is
a non-fatal bug) and return NULL ep. Call sites treat a NULL
return value as an error.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since the quirks all apply to implicit feedback (the source endpoint
is always a data endpoint), there's no need to set and check
a flag for it.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
An implicit feedback endpoint can only be a capture source. The
consumer (sink) of the implicit feedback endpoint is therefore limited
to playback EPs.
Check if the target endpoint is a playback first and remove redundant
checks.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since implicit_fb is not changed, !implicit_fb will always
be true - it is set only after these checks.
Similarly, there's also no need to set it at the top of the function.
Change the type of implicit_fb to bool (more appropriate).
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reverse logic on the conditions required to qualify for a sync endpoint
and remove one level of indendation.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Separate setting implicit feedback quirks from setting
a sync endpoint (which may also be explicit feedback or async).
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Setting the sync endpoint currently takes up about half of set_format().
Move it to a dedicated function.
No functional change.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
These really should be a single driver because they're fully integrated
in hardware. Make them so.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
Provide a helper macro which includes the sum of all enable bits in
the playback control register. This simplifies the code a little.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
Add PCM1792A spi mode codec support. This version implements only
a subset of functionalities. Tested connect to a pandaboard ES
device and based on recently pcm1681 codec.
Signed-off-by: Michael Trimarchi <michael@amarulasolutions.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
ASoC automatically creates snd_soc_dapm_dai_in and snd_soc_dapm_dai_out
widgets for DAI drivers, and adds them to the list. Later on, ASoC
creates automatic routes between these widgets and a widget with a
stream name.
We look for a snd_soc_dapm_dai_in or snd_soc_dapm_dai_out widget, and
use this to obtain the DAI structure. We then scan all widgets for
any with a stream name refering to either the capture or the playback
stream, and create routes.
If you have both a snd_soc_dapm_dai_in and a snd_soc_dapm_dai_out
referring to the same DAI structure, this ends up creating one set of
routes for the DAI for the snd_soc_dapm_dai_in widget, and a duplicated
set of routes for the snd_soc_dapm_dai_out widget.
Fix this by checking that the stream name for the widget matches the
DAI widget name.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
[Remaining patch from "ASoC: kirkwood: use devm_clk_get() for the
external clock" -- broonie]
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
We must init the delayed_work for codec-codec links
otherwise shutting down the DAI chain will fault when
calling flush_delayed_work_sync() on the linked DAI.
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Powering down PLL before switching to a mode that does not use it
is a bad idea. It would cause the SGTL5000 be without internal
clock supply, especially on the I2C interface, which would make
subsequent access to it fail.
Thus, in case of not using PLL any longer, first set the mode
control, then power down PLL.
Signed-off-by: Oskar Schirmer <oskar@scara.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Some devices have the problem that if a internal audio signal source is disabled
the output of the source becomes undefined or goes to a undesired state (E.g.
DAC output goes to ground instead of VMID). In this case it is necessary, in
order to avoid unwanted clicks and pops, to disable any mixer input the signal
feeds into or to active a mute control along the path to the output. Often it is
still desirable to expose the same mixer input control to userspace, so cerain
paths can sill be disabled manually. This means we can not use conventional DAPM
to manage the mixer input control. This patch implements a method for letting
DAPM overwrite the state of a userspace visible control. I.e. DAPM will disable
the control if the path on which the control sits becomes inactive. Userspace
will then only see a cached copy of the controls state. Once DAPM powers the
path up again it will sync the userspace setting with the hardware and give
control back to userspace.
To implement this a new widget type is introduced. One widget of this type will
be created for each DAPM kcontrol which has the auto-disable feature enabled.
For each path that is controlled by the kcontrol the widget will be connected to
the source of that path. The new widget type behaves like a supply widget,
which means it will power up if one of its sinks are powered up and will only
power down if all of its sinks are powered down. In order to only have the mixer
input enabled when the source signal is valid the new widget type will be
disabled before all other widget types and only be enabled after all other
widget types.
E.g. consider the following simplified example. A DAC is connected to a mixer
and the mixer has a control to enable or disable the signal from the DAC.
+-------+
+-----+ | |
| DAC |-----[Ctrl]-| Mixer |
+-----+ : | |
| : +-------+
| :
+-------------+
| Ctrl widget |
+-------------+
If the control has the auto-disable feature enabled we'll create a widget for
the control. This widget is connected to the DAC as it is the source for the
mixer input. If the DAC powers up the control widget powers up and if the DAC
powers down the control widget is powered down. As long as the control widget
is powered down the hardware input control is kept disabled and if it is enabled
userspace can freely change the control's state.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Merge these two structures together; nothing other than the I2S and
DMA driver makes use of struct kirkwood_dma_data, and it's not like
struct kirkwood_dma_data is really just used to convey DMA specific
data to the backend; it's more a general shared structure between the
two halves.
This will later allow kirkwood-dma.c and kirkwood-i2s.c to be merged
together.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
CODECs without any outputs now remain powered down, which means any
paths to these codecs also remain powered down.
Add an always-enabled output pin widget to the spdif transceiver codec.
This enables DAPM to correctly identify that the spdif transceiver is
in use when playback is enabled, which will then allow DAPM to power up
any links from the CPU DAI to the S/PDIF transceiver.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Mark Brown <broonie@linaro.org>
The snd_hda_jack_set_gating_jack() call didn't work when
auto_{mute,mic} is suppressed because (1) am_entry is
not filled with nid of the mic pin. (2) The jacks are not
created (by snd_hda_jack_detect_enable_callback) before the
snd_hda_jack_set_gating_jack call.
Now we use the first input pin nid directly, and create the jack if it
doesn't exist yet.
Signed-off-by: Chih-Chung Chang <chihchung@chromium.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
A fixup for Apple Mac Mini was lost during the adaption to the generic
parser because the fallback for the generic ID 8384:7680 was dropped,
and it resulted in the silence output (and maybe other problems).
Unfortunately, just adding the missing subsystem ID wasn't enough, in
this case. The subsystem ID of this machine is 0000:0100 (what Apple
thought...?), and since snd_hda_pick_fixup() doesn't take the vendor
id zero into account, the driver ignored this entry. Now it's fixed
to regard the vendor id zero as a valid value.
Reported-and-tested-by: Linus Torvalds <torvalds@linux-foundation.org>
Cc: <stable@vger.kernel.org> [v3.9+]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
list_first_entry() will always return a valid pointer, even if the list is
empty. So the check whether path is NULL will always be false. So we end up
calling dapm_create_or_share_mixmux_kcontrol() with a path struct that points
right in the middle of the widget struct and by trying to modify the path the
widgets memory will become corrupted. Fix this by using list_emtpy() to check if
the widget doesn't have any paths.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Tested-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Cc: stable@vger.kernel.org
When calling krealloc for the kcontrol data the items in the path list that
point back to the head of the list will now point to freed memory, which causes
the list to become corrupted. To fix this, instead of resizing the whole data
struct, only resize the widget list.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
The SGTL5000 Capture Attenuate Switch (or "ADC Volume Range Reduction"
as it is called in the manual) is single bit only.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When a sound capture/playback is terminated while a playback/capture
is running, power_vag_event() will clear SGTL5000_CHIP_ANA_POWER in
the SND_SOC_DAPM_PRE_PMD event, thus muting the respective other
channel.
Don't clear SGTL5000_CHIP_ANA_POWER when both DAC and ADC are active
to prevent this.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Reviewed-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
snd_soc_cnew() can return NULL, so we should check the result before trying to
use it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
More for neatness than for any great utility. Really we shouldn't be
creating the child device at all, refactoring will follow.
Signed-off-by: Mark Brown <broonie@linaro.org>
No need to hold on to the `codec' pointer. We can use the `dsp'
pointer and grab all the information we need from there. This
makes the parameters for the functions a bit more sane and idiomatic.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
PCM1681 can be controlled via I2C, SPI or in bootstrap mode (no control mode). This code add
support only for I2C mode.
Signed-off-by: Marek Belisko <marek.belisko@streamunlimited.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
A fix to make sure userspace knows when control writes have caused a
change in value, fixing some UIs, plus a few few driver fixes mainly
cleaning up issues from recent refactorings on less mainstream platforms.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.12 (GNU/Linux)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=WtLE
-----END PGP SIGNATURE-----
Merge tag 'asoc-v3.11-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-linus
ASoC: Fixes for v3.11
A fix to make sure userspace knows when control writes have caused a
change in value, fixing some UIs, plus a few few driver fixes mainly
cleaning up issues from recent refactorings on less mainstream platforms.
We should be allocating our buffers for the SPI transfers
from the DMA zone.
Signed-off-by: Dimitris Papastamos <dp@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Just recently OMAP4 legacy boot support has been removed. No reason to keep
the code used by the legacy boot (pdata based) since neither OMAP4 or OMAP5
can boot in this mode.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should be
replaced with IS_ERR(), and also remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Mark Brown