Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a definition for PHY ID mask for improving code readability.
Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SGMII mode, we observed an autonegotiation issue
after power-down-up cycles where the copper side
reports successful link establishment but the
SGMII side's link is down.
This happened in a setup where the at8031 is
connected over SGMII to a eTSEC (fsl gianfar),
but so far could not be reproduced with other
Ethernet device / driver combinations.
This commit adds a wrapper function for at8031
that in case of operating in SGMII mode double
checks SGMII link state when generic aneg_done()
succeeds. It prints a warning on failure but
intentionally does not try to recover from this
state. As a result, if you ever see a warning
'803x_aneg_done: SGMII link is not ok' you will
end up having an Ethernet link up but won't get
any data through. This should not happen, if it
does, please contact the module maintainer.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 98267311fe.
Suspending the SGMII alongside the copper side
made the at803x inaccessable while powered down,
e.g. it can't be re-probed after suspend.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 13a56b44 ("at803x: Add support for hardware reset") added a
work-around for a hardware bug on the AT8030. However, the work-around
was being called for all 803x PHYs, even those that don't need it.
Function at803x_link_change_notify() checks to make sure that it only
resets the PHY on the 8030, but it makes more sense to not call that
function at all if it isn't needed.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes the dependency on GPIOLIB for non faulty PHYs.
Indeed, without this patch, if GPIOLIB is not selected
devm_gpiod_get_optional() will return -ENOSYS and the driver probe
call will fail, regardless of the actual PHY hardware.
Out of the 3 PHYs supported by this driver (AT8030, AT8031, AT8035),
only AT8030 presents the issues that commit 13a56b4493 ("net: phy:
at803x: Add support for hardware reset") attempts to work-around by
using a 'reset' GPIO line.
Hence, only AT8030 should depend on GPIOLIB operating properly.
Fixes: 13a56b4493 ("net: phy: at803x: Add support for hardware reset")
Signed-off-by: Sebastian Frias <sf84@laposte.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver of course "knows" that the chip's reset signal is active low,
so it drives the GPIO to 0 to reset the PHY and to 1 otherwise; however
all this will only work iff the GPIO is specified as active-high in the
device tree! I think both the driver and the device trees (if there are
any -- I was unable to find them) need to be fixed in this case...
Fixes: 13a56b4493 ("net: phy: at803x: Add support for hardware reset")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
When operating the at803x in SGMII mode, resuming the chip
from power down brings up the copper-side link but leaves
the SGMII link in unconnected state (tested with at8031
attached to gianfar). In effect, this caused a permanent
link loss once the related interface was put down.
This patch ensures that power down handling in supspend()
and resume() is also applied to the SGMII link.
Signed-off-by: Zefir Kurtisi <zefir.kurtisi@neratec.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also use them instead of a magic value when enabling the interrupts.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
at803x currently automatically enables the RGMII TX clock delay when the
phy interface mode is PHY_INTERFACE_MODE_RGMII_TXID. The same should be
done when PHY_INTERFACE_MODE_RGMII_ID is specified.
Use a similar logic to enable the RGMII RX clock delay as well.
at803x_context_{save,restore} were not touched because these are only
used on AR8030 which is a RMII phy (RGMII clock delays are irrelevant).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The 8030 is only a "RMII Fast Ethernet PHY", thus it must not have the
SUPPORTED_1000* bits set.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than have each driver set the driver owner field, do it once in
the core code. This will also help with later changes, when the device
structure will move.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Not all devices attached to an MDIO bus are phys. So add an
mdio_device structure to represent the generic parts of an mdio
device, and place this structure into the phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
In preparation for moving some of the phy_device structure members,
add macros for printing errors and debug information.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit 77a993942 "phy/at8031: enable at8031 to work on interrupt mode"
added interrupt support for the 8031 PHY but left out the other two
chips supported by this driver.
This patch sets the .ack_interrupt and .config_intr functions for the
8030 and 8035 drivers as well.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since 39b2bbe3d7 (gpio: add flags argument to gpiod_get*() functions)
which appeared in v3.17-rc1, the gpiod_get* functions take an additional
parameter that allows to specify direction and initial value for output.
Moreover use devm_gpiod_get_optional instead of ignoring all errors
returned by devm_gpiod_get and simplify accordingly.
The result is more strict error handling which is good.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replace module init/exit which only calls phy_drivers_register with
module_phy_driver macro.
Tested using Micrel driver, and otherwise compile-tested only.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
drivers/net/phy/at803x.c:196:26-32: ERROR: application of sizeof to pointer
sizeof when applied to a pointer typed expression gives the size of
the pointer
Generated by: scripts/coccinelle/misc/noderef.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Acked-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The AT8030 will enter a FIFO error mode if a packet is transmitted while
the cable is unplugged. This hardware issue is acknowledged by the
vendor, and the only proposed solution is to conduct a hardware reset
via the external pin each time the link goes down. There is apparantly
no way to fix up the state via the register set.
This patch adds support for reading a 'reset-gpios' property from the DT
node of the PHY. If present, this gpio is used to apply a hardware reset
each time a 'link down' condition is detected. All relevant registers
are read out before, and written back after the reset cycle.
Doing this every time the link goes down might seem like overkill, but
there is unfortunately no way of figuring out whether the PHY is in
such a lock-up state. Hence, this is the only way of reliably fixing up
things.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes magic values from two tables and also allows us to match
against specific PHY models at runtime.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was caught when using a spatch (aka. coccinelle) script
written by Joe Perches.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Shruti Kanetkar <Shruti@Freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the generic bits from genphy_config_init() instead of implementing
the same functionality again.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The at8031 can work on polling mode and interrupt mode.
Add ack_interrupt and config intr funcs to enable
interrupt mode for it.
Signed-off-by: Zhao Qiang <B45475@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When WOL is enabled, the chip can't be put into power-down (BMCR_PDOWN)
mode, as that will also switch off the MAC, which consequently leads to
a link loss.
Use BMCR_ISOLATE in that case, which will at least save us some
milliamperes in comparison to normal operation mode.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Just a cosmetic cleanup.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
at803x supports Atheros 8030, 8031 and 8035 PHYs. 8031 was missing from
the mdio device id table.
Signed-off-by: Helmut Schaa <helmut.schaa@googlemail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for Atheros 8031 phy driver.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for RGMII TX delay configuration on Atheros 803X,
this can be enabled in debug registers. With this patch,
PHY_INTERFACE_MODE_RGMII_TXID modes are now supported.
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
WOL is initilized in phy config_init, but there are standard apis
(set_wol/get_wol) for WOL in phy frame work. So this patch moves
WOL specific code from config_init to wol standard apis.
Cc: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make use of phy_drivers_register/phy_drivers_unregister to register/unregister
multiple phy drivers in a single module.
Cc: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver add support for wake over lan on AT803x phys.
Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller