The alias->unit field is an array, so to check that it is not set we
should see if it is an empty string, i.e. alias->unit[0], instead of
checking alias->unit != NULL, as this will _always_ evaluate to 'true'.
Pointed out by clang.
Acked-by: Jiri Olsa <jolsa@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/20170214182435.GD4458@kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
100% reproducible issue found on SKL SkullCanyon NUC with two external
DP daisy-chained monitors in DP/MST mode. When turning off or changing
the input of the second monitor the machine stops with a kernel
oops. This issue happened with 4.8.8 as well as drm/drm-intel-nightly.
This issue is traced to an inconsistent control flow in
drm_dp_update_payload_part1(): the 'port' pointer is set to NULL at the
same time as 'req_payload.num_slots' is set to zero, but the pointer is
dereferenced even when req_payload.num_slot is zero.
The problematic dereference was introduced in commit dfda0df34
("drm/mst: rework payload table allocation to conform better") and may
impact all versions since v3.18
The fix suggested by Chris Wilson removes the kernel oops and was found to
work well after 10mn of monkey-testing with the second monitor power and
input buttons
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=98990
Fixes: dfda0df342 ("drm/mst: rework payload table allocation to conform better.")
Cc: Dave Airlie <airlied@redhat.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Nathan D Ciobanu <nathan.d.ciobanu@linux.intel.com>
Cc: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Cc: Sean Paul <seanpaul@chromium.org>
Cc: <stable@vger.kernel.org> # v3.18+
Tested-by: Nathan D Ciobanu <nathan.d.ciobanu@linux.intel.com>
Reviewed-by: Dhinakaran Pandiyan <dhinakaran.pandiyan@intel.com>
Signed-off-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: http://patchwork.freedesktop.org/patch/msgid/1487076561-2169-1-git-send-email-jani.nikula@intel.com
There is a potential race between fuse_dev_do_write()
and request_wait_answer() contexts as shown below:
TASK 1:
__fuse_request_send():
|--spin_lock(&fiq->waitq.lock);
|--queue_request();
|--spin_unlock(&fiq->waitq.lock);
|--request_wait_answer():
|--if (test_bit(FR_SENT, &req->flags))
<gets pre-empted after it is validated true>
TASK 2:
fuse_dev_do_write():
|--clears bit FR_SENT,
|--request_end():
|--sets bit FR_FINISHED
|--spin_lock(&fiq->waitq.lock);
|--list_del_init(&req->intr_entry);
|--spin_unlock(&fiq->waitq.lock);
|--fuse_put_request();
|--queue_interrupt();
<request gets queued to interrupts list>
|--wake_up_locked(&fiq->waitq);
|--wait_event_freezable();
<as FR_FINISHED is set, it returns and then
the caller frees this request>
Now, the next fuse_dev_do_read(), see interrupts list is not empty
and then calls fuse_read_interrupt() which tries to access the request
which is already free'd and gets the below crash:
[11432.401266] Unable to handle kernel paging request at virtual address
6b6b6b6b6b6b6b6b
...
[11432.418518] Kernel BUG at ffffff80083720e0
[11432.456168] PC is at __list_del_entry+0x6c/0xc4
[11432.463573] LR is at fuse_dev_do_read+0x1ac/0x474
...
[11432.679999] [<ffffff80083720e0>] __list_del_entry+0x6c/0xc4
[11432.687794] [<ffffff80082c65e0>] fuse_dev_do_read+0x1ac/0x474
[11432.693180] [<ffffff80082c6b14>] fuse_dev_read+0x6c/0x78
[11432.699082] [<ffffff80081d5638>] __vfs_read+0xc0/0xe8
[11432.704459] [<ffffff80081d5efc>] vfs_read+0x90/0x108
[11432.709406] [<ffffff80081d67f0>] SyS_read+0x58/0x94
As FR_FINISHED bit is set before deleting the intr_entry with input
queue lock in request completion path, do the testing of this flag and
queueing atomically with the same lock in queue_interrupt().
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Miklos Szeredi <mszeredi@redhat.com>
Fixes: fd22d62ed0 ("fuse: no fc->lock for iqueue parts")
Cc: <stable@vger.kernel.org> # 4.2+
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_rcv_established() can now run in process context.
We need to disable BH while acquiring tcp probe spinlock,
or risk a deadlock.
Fixes: 5413d1babe ("net: do not block BH while processing socket backlog")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Ricardo Nabinger Sanchez <rnsanchez@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Because of <linux/libc-compat.h> interface limitations, <netinet/in.h>
provided by libc cannot be included after <linux/in.h>, therefore any
header that includes <netinet/in.h> cannot be included after <linux/in.h>.
Change uapi/linux/l2tp.h, the last uapi header that includes
<netinet/in.h>, to include <linux/in.h> and <linux/in6.h> instead of
<netinet/in.h> and use __SOCK_SIZE__ instead of sizeof(struct sockaddr)
the same way as uapi/linux/in.h does, to fix linux/if_pppol2tp.h userspace
compilation errors like this:
In file included from /usr/include/linux/l2tp.h:12:0,
from /usr/include/linux/if_pppol2tp.h:21,
/usr/include/netinet/in.h:31:8: error: redefinition of 'struct in_addr'
Fixes: 47c3e7783b ("net: l2tp: deprecate PPPOL2TP_MSG_* in favour of L2TP_MSG_*")
Signed-off-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
LED class heartbeat trigger allowed only for blinking with max_brightness
value. This patch adds more flexibility by exploiting part of LED core
software blink infrastructure.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
LED subsystem supports POLLPRI on "brightness_hw_changed" sysfs file
of LED class devices. This tool demonstrates how to use the feature.
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
This reverts commit 63d0f0a695.
It caused a regression on platforms where I2C controller is synthesized
with dynamic TAR update disabled. Detection code is testing is bit
DW_IC_CON_10BITADDR_MASTER in register DW_IC_CON read-only but fails to
restore original value in case bit is read-write.
Instead of fixing this we revert the commit since it was preparation for
the commit 0317e6c0f1 ("i2c: designware: do not disable adapter after
transfer") which was also reverted.
Reported-by: Shah Nehal-Bakulchandra <Nehal-bakulchandra.Shah@amd.com>
Reported-by: Suravee Suthikulpanit <suravee.suthikulpanit@amd.com>
Acked-By: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: <stable@vger.kernel.org> # v4.9+
Fixes: 63d0f0a695 ("i2c: designware: detect when dynamic tar update is possible")
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Reported as a Kaffeine bug:
https://bugs.kde.org/show_bug.cgi?id=375811
The USB control messages require DMA to work. We cannot pass
a stack-allocated buffer, as it is not warranted that the
stack would be into a DMA enabled area.
On Kernel 4.9, the default is to not accept DMA on stack anymore
on x86 architecture. On other architectures, this has been a
requirement since Kernel 2.2. So, after this patch, this driver
should likely work fine on all archs.
Tested with USB ID 2040:5510: Hauppauge Windham
Cc: stable@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Multiple threads can call fanout_add() at the same time.
We need to grab fanout_mutex earlier to avoid races that could
lead to one thread freeing po->rollover that was set by another thread.
Do the same in fanout_release(), for peace of mind, and to help us
finding lockdep issues earlier.
Fixes: dc99f60069 ("packet: Add fanout support.")
Fixes: 0648ab70af ("packet: rollover prepare: per-socket state")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In the current driver, the MTU is set to the maximum value
capable for the backing device. This decision turned out to
be a mistake as it led to confusion among users. The expected
initial MTU value used for other IBM vNIC capable operating
systems is 1500, with the maximum value (9000) reserved for
when Jumbo frames are enabled. This patch sets the MTU to
the default value for a net device.
It also corrects a discrepancy between MTU values received from
firmware, which includes the ethernet header length, and net
device MTU values.
Finally, it removes redundant min/max MTU assignments after device
initialization.
Signed-off-by: Thomas Falcon <tlfalcon@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a copy-paste error, which hides breaking of resume
for CPSW driver: there was replaced netdev_priv() to ndev_to_cpsw(ndev)
in suspend, but left it unchanged in resume.
Fixes: 606f399395
(ti: cpsw: move platform data and slaves info to cpsw_common)
Reported-by: Alexey Starikovskiy <AStarikovskiy@topcon.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In a few cases we were using 'enum map_type' and that triggered this
warning when using clang:
util/session.c:1923:16: error: comparison of constant 2 with expression of type 'enum map_type' is always true
[-Werror,-Wtautological-constant-out-of-range-compare]
for (i = 0; i < MAP__NR_TYPES; ++i) {
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-i6uyo6bsopa2dghnx8qo7rri@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
So set it only for other compilers, allowing us to overcome yet another
build failure due to an inexistent clang -W option:
error: unknown warning option '-Wno-override-init'; did you mean '-Wno-override-module'? [-Werror,-Wunknown-warning-option]
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-oaa1ici3j8nygp4pzl2oobh3@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
As this is a GNU extension and while harmless in this case, we can do
the same thing in a more clearer way by using a existing thread_map and
cpu_map constructors:
With this we avoid this while compiling with clang:
util/evsel.c:1659:17: error: field 'map' with variable sized type 'struct cpu_map' not at the end of a struct or class is a GNU extension
[-Werror,-Wgnu-variable-sized-type-not-at-end]
struct cpu_map map;
^
util/evsel.c:1667:20: error: field 'map' with variable sized type 'struct thread_map' not at the end of a struct or class is a GNU extension
[-Werror,-Wgnu-variable-sized-type-not-at-end]
struct thread_map map;
^
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-207juvrqjiar7uvas2s83v5i@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Genuine problem detected with clang, the warnings are spot on:
util/probe-event.c:2079:7: error: variable 'map' is used uninitialized whenever 'if' condition is false [-Werror,-Wsometimes-uninitialized]
if (addr) {
^~~~
util/probe-event.c:2094:6: note: uninitialized use occurs here
if (map && !is_kprobe) {
^~~
util/probe-event.c:2079:3: note: remove the 'if' if its condition is always true
if (addr) {
^~~~~~~~~~
util/probe-event.c:2075:8: error: variable 'map' is used uninitialized whenever 'if' condition is true [-Werror,-Wsometimes-uninitialized]
if (kernel_get_symbol_address_by_name(tp->symbol,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
util/probe-event.c:2094:6: note: uninitialized use occurs here
if (map && !is_kprobe) {
^~~
util/probe-event.c:2075:4: note: remove the 'if' if its condition is always false
if (kernel_get_symbol_address_by_name(tp->symbol,
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
util/probe-event.c:2064:17: note: initialize the variable 'map' to silence this warning
struct map *map;
^
= NULL
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-m3501el55i10hctfbmi2qxzr@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
As this is a GNU extension and while harmless in this case, we can do
the same thing in a more clearer way by using an existing thread_map
constructor.
With this we avoid this while compiling with clang:
util/parse-events.c:2024:21: error: field 'map' with variable sized type 'struct thread_map' not at the end of a struct or class is a GNU extension
[-Werror,-Wgnu-variable-sized-type-not-at-end]
struct thread_map map;
^
1 error generated.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-tqocbplnyyhpst6drgm2u4m3@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
As this is a GNU extension and while harmless in this case, we can do
the same thing in a more clearer way by using an existing thread_map
constructor.
With this we avoid this while compiling with clang:
builtin-record.c:659:21: error: field 'map' with variable sized type 'struct thread_map' not at the end of a struct or class is a GNU extension
[-Werror,-Wgnu-variable-sized-type-not-at-end]
struct thread_map map;
^
1 error generated.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-c9drclo52ezxmwa7qxklin2y@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
End result is the same, its an ABI, so the struct won't change, avoid
using a GNU extension, so that we can catch other cases that may be bugs.
Caught when building with clang:
tests/parse-no-sample-id-all.c:53:20: error: field 'attr' with variable sized type 'struct attr_event' not at the end of a struct or class is a GNU extension
[-Werror,-Wgnu-variable-sized-type-not-at-end]
struct attr_event attr;
^
1 error generated.
Testing it:
# perf test sample_id
24: Parse with no sample_id_all bit set : Ok
#
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-e2vs1x771fc208uvxnwcf08b@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
When building with clang we get this error:
bench/numa.c:46:9: error: 'dprintf' macro redefined [-Werror,-Wmacro-redefined]
#define dprintf(x...) do { if (g && g->p.show_details >= 1) printf(x); } while (0)
^
/usr/include/bits/stdio2.h:145:12: note: previous definition is here
# define dprintf(fd, ...) \
^
CC /tmp/build/perf/tests/parse-no-sample-id-all.o
1 error generated.
So, make sure it is undefined before using that name.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: Hitoshi Mitake <mitake@dcl.info.waseda.ac.jp>
Cc: Jakub Jelen <jjelen@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-f654o2svtrutamvxt7igwz74@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
This reverts commit 60758d6668.
Now that libsubcmd makes sure that OPT_UINTEGER options will not
return negative values, we can revert this patch while addressing
the problem it solved:
# perf bench futex hash -t -4
# Running 'futex/hash' benchmark:
Error: switch `t' expects an unsigned numerical value
Usage: perf bench futex hash <options>
-t, --threads <n> Specify amount of threads
# perf bench futex hash -t-4
# Running 'futex/hash' benchmark:
Error: switch `t' expects an unsigned numerical value
Usage: perf bench futex hash <options>
-t, --threads <n> Specify amount of threads
#
IMO it is more reasonable to flat out refuse to process a negative
number than to silently turn it into an absolute value.
This also helps in silencing clang's complaint about asking for an
absolute value of an unsigned integer:
bench/futex-hash.c:133:10: error: taking the absolute value of unsigned type 'unsigned int' has no effect [-Werror,-Wabsolute-value]
nsecs = futexbench_sanitize_numeric(nsecs);
^
bench/futex.h:104:42: note: expanded from macro 'futexbench_sanitize_numeric'
#define futexbench_sanitize_numeric(__n) abs((__n))
^
bench/futex-hash.c:133:10: note: remove the call to 'abs' since unsigned values cannot be negative
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-2kl68v22or31vw643m2exz8x@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Options marked OPTION_UINTEGER or OPTION_U64 clearly indicates that an
unsigned value is expected, so just error out when a negative value is
passed, instead of returning something undesired to the tool.
E.g.:
# perf bench futex hash -t -4
# Running 'futex/hash' benchmark:
Error: switch `t' expects an unsigned numerical value
Usage: perf bench futex hash <options>
-t, --threads <n> Specify amount of threads
#
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Davidlohr Bueso <dbueso@suse.de>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-2mdn8s2raatyhz7tamrsz22r@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
In commit 98e3862ca2 ("kcm: fix 0-length case for kcm_sendmsg()")
I tried to avoid skb allocation for 0-length case, but missed
a check for NULL pointer in the non EOR case.
Fixes: 98e3862ca2 ("kcm: fix 0-length case for kcm_sendmsg()")
Reported-by: Dmitry Vyukov <dvyukov@google.com>
Cc: Tom Herbert <tom@herbertland.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Let bcm_qspi_bspi_flash_read() return all the requested bytes by breaking
up the reads for BSPI block into optimal chunks size that a BSPI block can
handle.
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Fix hardware setup of multicast address hash:
- Never clear the hardware hash (to avoid packet loss)
- Construct the hash register values in software and then write once
to hardware
Signed-off-by: Rui Sousa <rui.sousa@nxp.com>
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jonathan T. Leighton says:
====================
IPv4-mapped on wire, :: dst address issue
Under some circumstances IPv6 datagrams are sent with IPv4-mapped IPv6
addresses as the source. Given an IPv6 socket bound to an IPv4-mapped
IPv6 address, and an IPv6 destination address, both TCP and UDP will
will send packets using the IPv4-mapped IPv6 address as the source. Per
RFC 6890 (Table 20), IPv4-mapped IPv6 source addresses are not allowed
in an IP datagram. The problem can be observed by attempting to
connect() either a TCP or UDP socket, or by using sendmsg() with a UDP
socket. The patch is intended to correct this issue for all socket
types.
linux follows the BSD convention that an IPv6 destination address
specified as in6addr_any is converted to the loopback address.
Currently, neither TCP nor UDP consider the possibility that the source
address is an IPv4-mapped IPv6 address, and assume that the appropriate
loopback address is ::1. The patch adds a check on whether or not the
source address is an IPv4-mapped IPv6 address and then sets the
destination address to either ::ffff:127.0.0.1 or ::1, as appropriate.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check on the type of the source address for the case
where the destination address is in6addr_any. If the source is an
IPv4-mapped IPv6 source address, the destination is changed to
::ffff:127.0.0.1, and otherwise the destination is changed to ::1. This
is done in three locations to handle UDP calls to either connect() or
sendmsg() and TCP calls to connect(). Note that udpv6_sendmsg() delays
handling an in6addr_any destination until very late, so the patch only
needs to handle the case where the source is an IPv4-mapped IPv6
address.
Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a check for the problematic case of an IPv4-mapped IPv6
source address and a destination address that is neither an IPv4-mapped
IPv6 address nor in6addr_any, and returns an appropriate error. The
check in done before returning from looking up the route.
Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver supports the Lantiq SSC SPI controller in master
mode. This controller is found on Intel (former Lantiq) SoCs like
the Danube, Falcon, xRX200, xRX300.
The hardware uses two hardware FIFOs one for received and one for
transferred bytes. When the driver writes data into the transmit FIFO
the complete word is taken from the FIFO into a shift register. The
data from this shift register is then written to the wire. This driver
uses the interrupts signaling the status of the FIFOs and not the shift
register. It is also possible to use the interrupts for the shift
register, but they will send a signal after every word. When using the
interrupts for the shift register we get a signal when the last word is
written into the shift register and not when it is written to the wire.
After all FIFOs are empty the driver busy waits till the hardware is
not busy any more and returns the transfer status.
Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com>
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
When called by HW offloading drivers, the TC action (e.g
net/sched/act_mirred.c) code uses this_cpu logic, e.g
_bstats_cpu_update(this_cpu_ptr(a->cpu_bstats), bytes, packets)
per the kernel documention, preemption should be disabled, add that.
Before the fix, when running with CONFIG_PREEMPT set, we get a
BUG: using smp_processor_id() in preemptible [00000000] code: tc/3793
asserion from the TC action (mirred) stats_update callback.
Fixes: aad7e08d39 ('net/mlx5e: Hardware offloaded flower filter statistics support')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Declare device_type structure as const as it is only stored in the
type field of a device structure. This field is of type const, so add
const to the declaration of device_type structure.
File size before: drivers/hid/intel-ish-hid/ishtp/bus.o
text data bss dec hex filename
4260 336 16 4612 1204 hid/intel-ish-hid/ishtp/bus.o
File size after: drivers/hid/intel-ish-hid/ishtp/bus.o
text data bss dec hex filename
4324 272 16 4612 1204 hid/intel-ish-hid/ishtp/bus.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
-----BEGIN PGP SIGNATURE-----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=OTHY
-----END PGP SIGNATURE-----
Merge tag 'media/v4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A colorspace regression fix in V4L2 core and a CEC core bug that makes
it discard valid messages"
* tag 'media/v4.10-4' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] cec: initiator should be the same as the destination for, poll
[media] videodev2.h: go back to limited range Y'CbCr for SRGB and, ADOBERGB
The prox/range bits included in the Bluetooth reports from the Intuos Pro
were being ignored, leading to two issues. Firstly, the pen would never
announce a BTN_TOOL_PEN event with value 0, leaving userspace to believe
the pen was always active. Secondly, the driver would continue to send
events for data while the packet's "prox" bit was clear. This can lead
to sudden incorrect pointer jumps if the pen is slowly moved away from
the tablet surface.
Signed-off-by: Jason Gerecke <jason.gerecke@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
To avoid this when using clang:
warning: optimization level '-O6' is not supported; using '-O3' instead
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-kaghp8ddvzdsg03putemcq96@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
To allow building with clang, avoiding:
error: unknown warning option '-Wstrict-aliasing=3'; did you mean '-Wstring-plus-int'? [-Werror,-Wunknown-warning-option]
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-xvthlvmhzfnt7jx73jgmaea1@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Last time we did that was when we enabled Bulldozer. Now, we enabled Zen
so it is only natural ... :-)
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Yazen Ghannam <Yazen.Ghannam@amd.com>
The build of tilegx allmodconfig fails with:
../arch/tile/include/asm/div64.h:5:15: error: unknown type name 'u64'
static inline u64 mul_u32_u32(u32 a, u32 b)
^~~
../arch/tile/include/asm/div64.h:5:31: error: unknown type name 'u32'
static inline u64 mul_u32_u32(u32 a, u32 b)
^~~
../arch/tile/include/asm/div64.h:5:38: error: unknown type name 'u32'
static inline u64 mul_u32_u32(u32 a, u32 b)
^~~
In file included from ../fs/ubifs/ubifs.h:26:0,
from ../fs/ubifs/shrinker.c:42:
../include/linux/math64.h: In function 'mul_u64_u32_shr':
../arch/tile/include/asm/div64.h:9:21: error: implicit declaration of
function 'mul_u32_u32' [-Werror=implicit-function-declaration]
Include the linux/types.h in tiles div64.h to slve the problem.
Fixes: 9e3d6223d2 ("math64, timers: Fix 32bit mul_u64_u32_shr() and friends")
Signed-off-by: Sudip Mukherjee <sudip.mukherjee@codethink.co.uk>
Acked-by: Chris Metcalf <cmetcalf@mellanox.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Link: http://lkml.kernel.org/r/1485275961-20112-1-git-send-email-sudip.mukherjee@codethink.co.uk
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Commit 577fb13199 ("mmc: rework selection of bus speed mode")
refactored bus width selection code to mmc_select_bus_width().
However, it also altered the behavior to not call the selection code in
non-high-speed modes anymore.
This causes 1-bit mode to always be used when the high-speed mode is not
enabled, even though 4-bit and 8-bit bus are valid bus widths in the
backwards-compatibility (legacy) mode as well (see e.g. 5.3.2 Bus Speed
Modes in JEDEC 84-B50). This results in a significant regression in
transfer speeds.
Fix the code to allow 4-bit and 8-bit widths even without high-speed
mode, as before.
Tested with a Zynq-7000 PicoZed 7020 board.
Fixes: 577fb13199 ("mmc: rework selection of bus speed mode")
Signed-off-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
New feature:
- Introduce the 'delta-abs' 'perf diff' compute method, that orders the
histogram entries by the absolute value of the percentage delta for a
function in two perf.data files, i.e. the functions that changed the
most (increase or decrease in samples) comes first (Namhyung Kim)
User visible:
- Improve message about tweaking the kernel.perf_event_paranoid setting,
telling how to make the change permanent by editing /etc/sysctl.conf
(Ingo Molnar)
Infrastructure:
- Introduce linux/compiler-gcc.h as a counterpart to the kernel's,
initially containing the definition of __fallthrough, more to
come (__maybe_unused, etc) (Arnaldo Carvalho de Melo)
- Fixes for problems uncovered by building tools/perf with clang, such
as always true tests of arrays against NULL and variables that sometimes
were used without being initialized (Arnaldo Carvalho de Melo, Steven Rostedt)
- Before loading a new ELF, clear global variables set by the
samples/bpf loader (Mickaël Salaün)
- Ignore already processed ELF sections in the samples/bpf
loader (Mickaël Salaün)
- Fix compile error in the scripting code with some perl5
versions (Wang YanQing)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2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=LCz9
-----END PGP SIGNATURE-----
Merge tag 'perf-core-for-mingo-4.11-20170213' of git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull perf/core improvements and fixes from Arnaldo Carvalho de Melo:
New features:
- Introduce the 'delta-abs' 'perf diff' compute method, that orders the
histogram entries by the absolute value of the percentage delta for a
function in two perf.data files, i.e. the functions that changed the
most (increase or decrease in samples) comes first (Namhyung Kim)
User visible changes:
- Improve message about tweaking the kernel.perf_event_paranoid setting,
telling how to make the change permanent by editing /etc/sysctl.conf
(Arnaldo Carvalho de Melo)
Infrastructure changes:
- Introduce linux/compiler-gcc.h as a counterpart to the kernel's,
initially containing the definition of __fallthrough, more to
come (__maybe_unused, etc) (Arnaldo Carvalho de Melo)
- Fixes for problems uncovered by building tools/perf with clang, such
as always true tests of arrays against NULL and variables that sometimes
were used without being initialized (Arnaldo Carvalho de Melo, Steven Rostedt)
- Before loading a new ELF, clear global variables set by the
samples/bpf loader (Mickaël Salaün)
- Ignore already processed ELF sections in the samples/bpf
loader (Mickaël Salaün)
- Fix compile error in the scripting code with some perl5
versions (Wang YanQing)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Herbert Xu says:
====================
rhashtable: Handle table allocation failure during insertion
v2 -
Added Ack to patch 2.
Fixed RCU annotation in code path executed by rehasher by using
rht_dereference_bucket.
v1 -
This series tackles the problem of table allocation failures during
insertion. The issue is that we cannot vmalloc during insertion.
This series deals with this by introducing nested tables.
The first two patches removes manual hash table walks which cannot
work on a nested table.
The final patch introduces nested tables.
I've tested this with test_rhashtable and it appears to work.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code that handles GFP_ATOMIC kmalloc failure on
insertion. As we cannot use vmalloc, we solve it by making our
hash table nested. That is, we allocate single pages at each level
and reach our desired table size by nesting them.
When a nested table is created, only a single page is allocated
at the top-level. Lower levels are allocated on demand during
insertion. Therefore for each insertion to succeed, only two
(non-consecutive) pages are needed.
After a nested table is created, a rehash will be scheduled in
order to switch to a vmalloced table as soon as possible. Also,
the rehash code will never rehash into a nested table. If we
detect a nested table during a rehash, the rehash will be aborted
and a new rehash will be scheduled.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two problems with the function tipc_sk_reinit. Firstly
it's doing a manual walk over an rhashtable. This is broken as
an rhashtable can be resized and if you manually walk over it
during a resize then you may miss entries.
Secondly it's missing memory barriers as previously the code used
spinlocks which provide the barriers implicitly.
This patch fixes both problems.
Fixes: 07f6c4bc04 ("tipc: convert tipc reference table to...")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Acked-by: Ying Xue <ying.xue@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function glock_hash_walk walks the rhashtable by hand. This
is broken because if it catches the hash table in the middle of
a rehash, then it will miss entries.
This patch replaces the manual walk by using the rhashtable walk
interface.
Fixes: 88ffbf3e03 ("GFS2: Use resizable hash table for glocks")
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
When sending ARP requests over AX.25 links the hwaddress in the neighbour
cache are not getting initialized. For such an incomplete arp entry
ax2asc2 will generate an empty string resulting in /proc/net/arp output
like the following:
$ cat /proc/net/arp
IP address HW type Flags HW address Mask Device
192.168.122.1 0x1 0x2 52:54:00:00:5d:5f * ens3
172.20.1.99 0x3 0x0 * bpq0
The missing field will confuse the procfs parsing of arp(8) resulting in
incorrect output for the device such as the following:
$ arp
Address HWtype HWaddress Flags Mask Iface
gateway ether 52:54:00:00:5d:5f C ens3
172.20.1.99 (incomplete) ens3
This changes the content of /proc/net/arp to:
$ cat /proc/net/arp
IP address HW type Flags HW address Mask Device
172.20.1.99 0x3 0x0 * * bpq0
192.168.122.1 0x1 0x2 52:54:00:00:5d:5f * ens3
To do so it change ax2asc to put the string "*" in buf for a NULL address
argument. Finally the HW address field is left aligned in a 17 character
field (the length of an ethernet HW address in the usual hex notation) for
readability.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes an issue where the type of counters in the queue(s)
and interface are not in sync (queue counters are int, interface
counters are long), causing incorrect reporting of tx/rx values
of the vif interface and unclear counter overflows.
This patch sets both counters to the u64 type.
Signed-off-by: Mart van Santen <mart@greenhost.nl>
Reviewed-by: Paul Durrant <paul.durrant@citrix.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two reasons for reporting wakeup event when dedicated wakeup
IRQ is triggered:
- wakeup events accounting, so proper statistical data will be
displayed in sysfs and debugfs;
- there are small window when System is entering suspend during which
dedicated wakeup IRQ can be lost:
dpm_suspend_noirq()
|- device_wakeup_arm_wake_irqs()
|- dev_pm_arm_wake_irq(X)
|- IRQ is enabled and marked as wakeup source
[1]...
|- suspend_device_irqs()
|- suspend_device_irq(X)
|- irqd_set(X, IRQD_WAKEUP_ARMED);
|- wakup IRQ armed
The wakeup IRQ can be lost if it's triggered at point [1]
and not armed yet.
Hence, fix above cases by adding simple pm_wakeup_event() call in
handle_threaded_wake_irq().
Fixes: 4990d4fe32 (PM / Wakeirq: Add automated device wake IRQ handling)
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Keerthy <j-keerthy@ti.com>
[ tony@atomide.com: added missing return to avoid warnings ]
Tested-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Arnaldo Carvalho de Melo