IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Some BIOSes will claim a large chunk of stolen space. Unless we
reclaim it, our aperture for remapping buffer objects will be
constrained. So clamp the stolen space to 32M and ignore the rest.
Fixes https://bugzilla.kernel.org/show_bug.cgi?id=15469 among others.
Adding the ignored stolen memory back into the general pool using the
memory hotplug code is left as an exercise for the reader.
Signed-off-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Reviewed-by: Simon Farnsworth <simon.farnsworth@onelan.com>
Tested-by: Artem S. Tashkinov <t.artem@mailcity.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
A side-effect of being able to use custom page allocations with the
sg_table is that it cannot reap the partially constructed scatterlist if
fails to allocate a page. So we need to call sg_free_table() ourselves
if sg_alloc_table() fails.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc Dave Airlie <airlied@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
[anholt: Split this patch out of a larger patch for Sandybridge fixes]
Signed-off-by: Eric Anholt <eric@anholt.net>
When "onboard video memory" is set do "disabled" in BIOS on Asus P4P800-VM
board (i865G), kernel oopses with memory corruption:
https://bugs.freedesktop.org/show_bug.cgi?id=28430
Fix that by cleanly aborting the initialization.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
BugLink: https://bugs.launchpad.net/bugs/597075
commit f1befe71fa introduced a
regression when detecting aperture size of some i915 adapters, e.g.,
those on the Intel Q35 chipset.
The original report: https://bugzilla.kernel.org/show_bug.cgi?id=15733
The regression report: https://bugzilla.kernel.org/show_bug.cgi?id=16294
According to the specification found at
http://intellinuxgraphics.org/VOL_1_graphics_core.pdf, the PCI config
space register I830_GMCH_CTRL is a mirror of GMCH Graphics
Control. The correct macro for isolating the aperture size bits is
therefore I830_GMCH_GMS_MASK along with the attendant changes to the
case statement.
Signed-off-by: Tim Gardner <tim.gardner@canonical.com>
Tested-by: Kees Cook <kees.cook@canonical.com>
Cc: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Eric Anholt <eric@anholt.net>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Eric Anholt <eric@anholt.net>
also drop the NORETRY we can probably nearly always satisfy order 1 allocs now,
and again the vmalloc path is there.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This fixes a sporadic oops at boot on G5 Power Macs. The table_end
variable has the address of the last byte of the table. Adding on
PAGE_SIZE means we flush too much, and if the page after the table
is not mapped for any reason, the kernel will oops. Instead we add
on 1 because flush_dcache_range() interprets its second argument as
the first byte past the range to be flushed.
Signed-off-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (41 commits)
drm/i915: add HAS_BSD check to i915_getparam
drm/i915: Honor sync polarity from VBT panel timing descriptors
drm/i915: Unmask interrupt for render engine on Sandybridge
drm/i915: Fix PIPE_CONTROL command on Sandybridge
drm/i915: Fix up address spaces in slow_kernel_write()
drm/i915: Use non-atomic kmap for slow copy paths
drm/i915: Avoid moving from CPU domain during pwrite
drm/i915: Cleanup after failed initialization of ringbuffers
drm/i915: Reject bind_to_gtt() early if object > aperture
drm/i915: Check error code whilst moving buffer to GTT domain.
drm/i915: Remove spurious warning "Failure to install fence"
drm/i915: Rebind bo if currently bound with incorrect alignment.
drm/i915: Include pitch in set_base debug statement.
drm/i915: Only print "nothing to do" debug message as required.
drm/i915: Propagate error from unbinding an unfenceable object.
drm/i915: Avoid nesting of domain changes when setting display plane
drm/i915: Hold the spinlock whilst resetting unpin_work along error path
drm/i915: Only print an message if there was an error
drm/i915: Clean up leftover bits from hws move to ring structure.
drm/i915: Add CxSR support on Pineview DDR3
...
References:
Bug 15733 - Crash when accessing nonexistent GTT entries in i915
https://bugzilla.kernel.org/show_bug.cgi?id=15733
On G33 and above, the size of the GTT space is determined by the GMCH
control register. Prior to this revision, the size is determined by the
size of the aperture. So we must careful to map and fill the appropriate
range depending on chipset.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Signed-off-by: Eric Anholt <eric@anholt.net>
Stanse found pci reference leaks in uli_agp_init and nforce3_agp_init
initialization functions.
The PCI devices are bridges, so it's not critical, but still worth fixing.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Cc: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'drm-for-2.6.35' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (207 commits)
drm/radeon/kms/pm/r600: select the mid clock mode for single head low profile
drm/radeon: fix power supply kconfig interaction.
drm/radeon/kms: record object that have been list reserved
drm/radeon: AGP memory is only I/O if the aperture can be mapped by the CPU.
drm/radeon/kms: don't default display priority to high on rs4xx
drm/edid: fix typo in 1600x1200@75 mode
drm/nouveau: fix i2c-related init table handlers
drm/nouveau: support init table i2c device identifier 0x81
drm/nouveau: ensure we've parsed i2c table entry for INIT_*I2C* handlers
drm/nouveau: display error message for any failed init table opcode
drm/nouveau: fix init table handlers to return proper error codes
drm/nv50: support fractional feedback divider on newer chips
drm/nv50: fix monitor detection on certain chipsets
drm/nv50: store full dcb i2c entry from vbios
drm/nv50: fix suspend/resume with DP outputs
drm/nv50: output calculated crtc pll when debugging on
drm/nouveau: dump pll limits entries when debugging is on
drm/nouveau: bios parser fixes for eDP boards
drm/nouveau: fix a nouveau_bo dereference after it's been destroyed
drm/nv40: remove some completed ctxprog TODOs
...
The current initialisation code probes 'unsupported' AGP devices
simply by calling its own probe function. It does not lock these
devices or even check whether another driver is already bound to
them.
We must use the device core to manage this. So if the specific
device id table didn't match anything and agp_try_unsupported=1,
switch the device id table and call driver_attach() again.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
SIS 760 is listed in the device tables for both amd64-agp and sis-agp.
amd64-agp is apparently preferable since it has workarounds for some
BIOS misconfigurations that sis-agp doesn't handle.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Convert most AGP chipset to use scratch page as default entries.
This help avoiding GPU querying 0 address and trigger computer
fault. With KMS and memory manager we bind/unbind AGP memory
constantly and it seems that some GPU are still doing AGP
traffic even after GPU report being idle with the memory segment.
Tested (radeon GPU KMS + Xorg + compiz + glxgears + quake3) on :
- SIS 1039:0001 & 1039:0003
- Intel 865 8086:2571
Compile tested for other bridges
V2 enable scratch page on uninorth
V3 fix unbound check in uninorth insert memory (Michel Dänzer)
V4 rebase on top of drm-next branch with the lastest intel AGP
changeset (stable should use version V3 of the patch)
Signed-off-by: Jerome Glisse <jglisse@redhat.com>
Signed-off-by: Michel Dänzer <michel@daenzer.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On my 945 laptop + radeon GPU, I was getting an oops on boot without this
check which seems to have gotten dropped in the rework.
Signed-off-by: Dave Airlie <airlied@redhat.com>
* 'anholt/drm-intel-next' of /home/airlied/kernel/drm-next: (48 commits)
agp/intel-gtt: kill previous_size assignments
agp/intel-gtt: kill intel_i830_tlbflush
agp/intel: split out gmch/gtt probe, part 1
agp/intel: kill mutli_gmch_chip
agp/intel: uncoditionally reconfigure driver on resume
agp/intel: split out the GTT support
agp/intel: introduce intel-agp.h header file
drm/i915: Don't touch PORT_HOTPLUG_EN in intel_dp_detect()
drm/i915/pch: Use minimal number of FDI lanes (v2)
drm/i915: Add the support of memory self-refresh on Ironlake
drm/i915: Move Pineview CxSR and watermark code into update_wm hook.
drm/i915: Only save/restore FBC on the platform that supports FBC
drm/i915: Fix the incorrect argument for SDVO SET_TV_format command
drm/i915: Add support of SDVO on Ibexpeak PCH
drm/i915: Don't enable pipe/plane/VCO early (wait for DPMS on).
drm/i915: do not read uninitialized ->dev_private
Revert "drm/i915: Use a dmi quirk to skip a broken SDVO TV output."
drm/i915: implement multifunction SDVO device support
drm/i915: remove unused intel_pipe_get_connector()
drm/i915: remove connector object in old output structure
...
Not needed for the GTT and inconsistent: Sometimes the _new_ size
was stored there ...
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
We don't use the generic insert/remove_memory functions that
require this. So kill this useless code.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
This is essentially the last piece of code that's tying intel-gtt.c
to intel-agp.c. Extract the probe code into it's own function so that
it can be moved to intel-gtt.c.
This requires some slight changes in the ordering of device probe function.
This patch just implements that for better bisectability in case this
introduces bugs.
The biggest change is that the gmch/gtt code doesn't execute a pci
resource fixup anymore. I've dug around in historical git trees, and
this change is to support the agp port on an old HP server with the
i440 intel chipset. So only needed for the agp driver.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Only two drivers were not in this table (7505 and g33), both non-mobile
chipsets. So they were most likely just missing. This is another step
to untangle the gtt from the agp driver.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
intel-agp.c contains actually two different drivers: An agp driver
for _physical_ agp slots an the gtt driver that is used by the intel
drm modules. Split them to prevent any further confusion.
This patch just moves the code and includes intel-gtt.c in intel-agp.c
Later patches will untangle these two drivers further.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
Intel definitions have spilled into agp.h. Create a header file for
them and also include it in efficion-agp.c 'cause it needs a few of
them.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: Ignore LVDS EDID when it is unavailabe or invalid
drm/i915: Add no_lvds entry for the Clientron U800
drm/i915: Rename many remaining uses of "output" to encoder or connector.
drm/i915: Rename intel_output to intel_encoder.
agp/intel: intel_845_driver is an agp driver!
drm/i915: introduce to_intel_bo helper
drm/i915: Disable FBC on 915GM and 945GM.
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
... not a GTT driver. So the additional chipset flush introduced in
commit 2162e6a2b0
Author: Dave Airlie <airlied@redhat.com>
Date: Wed Nov 21 16:36:31 2007 +1000
agp/intel: Add chipset flushing support for i8xx chipsets.
to fix a GTT problem makes absolutely no sense. If this would really be needed
for AGP chipsets, too, we should add it to all i8xx agp drivers, not just one.
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Signed-off-by: Eric Anholt <eric@anholt.net>
This CPU should be coherent with graphics in this direction, though
flushing graphics caches are still required. Fixes a system reset on
module load on Sandybridge with 4G+ memory.
Signed-off-by: Eric Anholt <eric@anholt.net>
This is similar to 14bc490bbd which
respected it for how much of the GTT we would actually use. Now we
won't clear beyond allocated memory when filling the GTT with scratch
page addresses.
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, k8 nb: Fix boot crash: enable k8_northbridges unconditionally on AMD systems
x86, UV: Fix target_cpus() in x2apic_uv_x.c
x86: Reduce per cpu warning boot up messages
x86: Reduce per cpu MCA boot up messages
x86_64, cpa: Don't work hard in preserving kernel 2M mappings when using 4K already
de957628ce changed setting of the
x86_init.iommu.iommu_init function ptr only when GART IOMMU is
found.
One side effect of it is that num_k8_northbridges
is not initialized anymore if not explicitly
called. This resulted in uninitialized pointers in
<arch/x86/kernel/cpu/intel_cacheinfo.c:amd_calc_l3_indices()>,
for example, which uses the num_k8_northbridges thing through
node_to_k8_nb_misc().
Fix that through an initcall that runs right after the PCI
subsystem and does all the scanning. Then, remove initialization
in gart_iommu_init() which is a rootfs_initcall and we're
running before that.
What is more, since num_k8_northbridges is being used in other
places beside GART IOMMU, include it whenever we add AMD CPU
support. The previous dependency chain in kconfig contained
K8_NB depends on AGP_AMD64|GART_IOMMU
which was clearly incorrect. The more natural way in terms of
hardware dependency should be
AGP_AMD64|GART_IOMMU depends on K8_NB depends on CPU_SUP_AMD &&
PCI. Make it so Number One!
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Joerg Roedel <joerg.roedel@amd.com>
LKML-Reference: <20100312144303.GA29262@aftab>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Tested-by: Joerg Roedel <joerg.roedel@amd.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (151 commits)
vga_switcheroo: disable default y by new rules.
drm/nouveau: fix *staging* driver build with switcheroo off.
drm/radeon: fix typo in Makefile
vga_switcheroo: fix build on platforms with no ACPI
drm/radeon: Fix printf type warning in 64bit system.
drm/radeon/kms: bump the KMS version number for square tiling support.
vga_switcheroo: initial implementation (v15)
drm/radeon/kms: do not disable audio engine twice
Revert "drm/radeon/kms: disable HDMI audio for now on rv710/rv730"
drm/radeon/kms: do not preset audio stuff and start timer when not using audio
drm/radeon: r100/r200 ums: block ability for userspace app to trash 0 page and beyond
drm/ttm: fix function prototype to match implementation
drm/radeon: use ALIGN instead of open coding it
drm/radeon/kms: initialize set_surface_reg reg for rs600 asic
drm/i915: Use a dmi quirk to skip a broken SDVO TV output.
drm/i915: enable/disable LVDS port at DPMS time
drm/i915: check for multiple write domains in pin_and_relocate
drm/i915: clean-up i915_gem_flush_gpu_write_domain
drm/i915: reuse i915_gpu_idle helper
drm/i915: ensure lru ordering of fence_list
...
Fixed trivial conflicts in drivers/gpu/vga/Kconfig
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, cacheinfo: Enable L3 CID only on AMD
x86, cacheinfo: Remove NUMA dependency, fix for AMD Fam10h rev D1
x86, cpu: Print AMD virtualization features in /proc/cpuinfo
x86, cacheinfo: Calculate L3 indices
x86, cacheinfo: Add cache index disable sysfs attrs only to L3 caches
x86, cacheinfo: Fix disabling of L3 cache indices
intel-agp: Switch to wbinvd_on_all_cpus
x86, lib: Add wbinvd smp helpers
See http://bugzilla.kernel.org/show_bug.cgi?id=15021
Make sure that the appropriate AGP module is loaded and probed before
trying to set up the DRM. The DRM already depends on the AGP core,
but in this case we know the specific AGP driver we need too, and can
help users avoid the trap of loading the AGP driver after the DRM
driver.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
New memory control config reg at 0x50 should be used for stolen
memory size detection on Sandybridge.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Print official names for Pineview and Ironlake, which is Intel
GMA3150 and Intel HD graphics.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
In particular, several occurances of funny versions of 'success',
'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address',
'beginning', 'desirable', 'separate' and 'necessary' are fixed.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Joe Perches <joe@perches.com>
Cc: Junio C Hamano <gitster@pobox.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
This fixes the regression introduced by commit
42590a7501 ("x86/agp: Fix
agp_amd64_init and agp_amd64_cleanup").
The commit 61684ceaad fixed the
above regression but it's not enough. When amd64-agp is built as
a module, AGP isn't initialized, iommu is initialized, all the
aperture is owned by the iommu.
Reported-by: Marin Mitov <mitov@issp.bas.bg>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Marin Mitov <mitov@issp.bas.bg>
LKML-Reference: <20100204090802S.fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This fixes the regression introduced by commit
42590a7501 ("x86/agp: Fix
agp_amd64_init and agp_amd64_cleanup").
The above commit changes agp_amd64_init() not to do anything if
gart_iommu_aperture is not zero.
If GART iommu calls agp_amd64_init(), we need to skip
agp_amd64_init() when it's called later via module_init.
The problem is that gart_iommu_init() calls agp_amd64_init()
with not zero gart_iommu_aperture so agp_amd64_init() is never
initialized.
When gart_iommu_init() calls agp_amd64_init(), agp should be
always initialized.
Reported-by: Marin Mitov <mitov@issp.bas.bg>
Reported-by: Johannes Hirte <johannes.hirte@fem.tu-ilmenau.de>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Tested-by: Marin Mitov <mitov@issp.bas.bg>
Tested-by: Kevin Winchester <kjwinchester@gmail.com>
Cc: davej@redhat.com
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <20100125141006O.fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Simplify if-statement while at it.
[ hpa: we need to #include <asm/smp.h> ]
Cc: Dave Jones <davej@redhat.com>
Cc: David Airlie <airlied@linux.ie>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
LKML-Reference: <1264172467-25155-3-git-send-email-bp@amd64.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86, uv: Ensure hub revision set for all ACPI modes.
x86, uv: Add function retrieving node controller revision number
x86: xen: 64-bit kernel RPL should be 0
x86: kernel_thread() -- initialize SS to a known state
x86/agp: Fix agp_amd64_init and agp_amd64_cleanup
x86: SGI UV: Fix mapping of MMIO registers
x86: mce.h: Fix warning in header checks
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel:
drm/i915: enable 36bit physical address for hardware status page
drm/i915: fix eDP pipe mask
drm/i915: fix pixel color depth setting on eDP
drm/i915: parse eDP panel color depth from VBT block
drm/i915: disable LVDS downclock by default
drm/i915: Fix the incorrect cursor A bit definition in DSPFW2 register
drm/i915: Remove chatty execbuf failure message.
drm/i915: remove loop in Ironlake interrupt handler
drm/i915: Don't wait interruptible for possible plane buffer flush
drm/i915: try another possible DDC bus for the SDVO device with multiple outputs
drm/i915: Read the response after issuing DDC bus switch command
drm/i915: Don't use the child device parsed from VBT to setup HDMI/DP
drm/i915: Fix resume regression on MSI Wind U100 w/o KMS
drm/i915: Fix Ironlake M/N/P ranges to match the spec
drm/i915: Use find_pll function to calculate DPLL setting for LVDS downclock
drm/i915: Add HP nx9020/SamsungSX20S to ACPI LID quirk list
drm/i915: disable TV hotplug status check
Trivial conflicts in drivers/gpu/drm/i915/i915_drv.c due to i915
non-modeset suspend fix with different comment.
This enables possible 36bit address mask on 965G that use physical
address for hw status page.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
This fixes the regression introduced by the commit
f405d2c023.
The above commit fixes the following issue:
http://marc.info/?l=linux-kernel&m=126192729110083&w=2
However, it doesn't work properly when you remove and insert the
agp_amd64 module again.
agp_amd64_init() and agp_amd64_cleanup should be called only
when gart_iommu is not called earlier (that is, the GART IOMMU
is not enabled). We need to use 'gart_iommu_aperture' to see if
GART IOMMU is enabled or not.
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: mitov@issp.bas.bg
Cc: davej@redhat.com
LKML-Reference: <20100104161603L.fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'agp-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp/hp: fail gracefully if we don't find an IOC
agp/hp: fixup hp agp after ACPI changes
agp: correct missing cleanup on error in agp_add_bridge
Bail out if we don't find an enclosing IOC. Previously, if we didn't
find one, we tried to set things up using garbage for the SBA/IOC register
address, which causes a crash.
This crash only happens if firmware supplies a defective ACPI namespace, so
it doesn't fix any problems in the field.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Commit 15b8dd53f5 changed the string in info->hardware_id from a static
array to a pointer and added a length field. But instead of changing
"sizeof(array)" to "length", we changed it to "sizeof(length)" (== 4),
which corrupts the string we're trying to null-terminate.
We no longer even need to null-terminate the string, but we *do* need to
check whether we found a HID. If there's no HID, we used to have an empty
array, but now we have a null pointer.
The combination of these defects causes this oops:
Unable to handle kernel NULL pointer dereference (address 0000000000000003)
modprobe[895]: Oops 8804682956800 [1]
ip is at zx1_gart_probe+0xd0/0xcc0 [hp_agp]
http://marc.info/?l=linux-ia64&m=126264484923647&w=2
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Reported-by: Émeric Maschino <emeric.maschino@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
While investigating a kmemleak detected leak, I encountered the
agp_add_bridge function. It appears to be responsible for freeing
the agp_bridge_data in the case of a failure, but it is only doing
so for some errors.
Fix it to always free the bridge data if a failure condition is
encountered.
Signed-off-by: Kevin Winchester <kjwinchester@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
with CONFIG_GART_IOMMU enabled drivers/char/agp/amd64-agp.c has:
#ifndef CONFIG_GART_IOMMU
module_init(agp_amd64_init);
module_exit(agp_amd64_cleanup);
#endif
agp_amd64_init() was called via gart_iommu_init with
CONFIG_GART_IOMMU=y agp_amd64_init() was called via module_init
with CONFIG_GART_IOMMU=n
The commit 75f1cdf1dd changes the
x86 dma initialization routine: gart_iommu_init() is called only
when GART IOMMU is detected. So when GART IOMMU isn't detected,
agp_amd64_init isn't called.
Marin Mitov reported this issue:
http://marc.info/?l=linux-kernel&m=126192729110083&w=2
With this patch, agp_amd64_init() is always called via
module_init (the above ifndef is removed). If agp_amd64_init()
is called via gart_iommu_init() earlier, agp_amd64_init()
finishes without doing anything (when it is called via
module_init).
Reported-by: Marin Mitov <mitov@issp.bas.bg>
Tested-by: Marin Mitov <mitov@issp.bas.bg>
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: davej@redhat.com
LKML-Reference: <20091228181118C.fujita.tomonori@lab.ntt.co.jp>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (151 commits)
powerpc: Fix usage of 64-bit instruction in 32-bit altivec code
MAINTAINERS: Add PowerPC patterns
powerpc/pseries: Track previous CPPR values to correctly EOI interrupts
powerpc/pseries: Correct pseries/dlpar.c build break without CONFIG_SMP
powerpc: Make "intspec" pointers in irq_host->xlate() const
powerpc/8xx: DTLB Miss cleanup
powerpc/8xx: Remove DIRTY pte handling in DTLB Error.
powerpc/8xx: Start using dcbX instructions in various copy routines
powerpc/8xx: Restore _PAGE_WRITETHRU
powerpc/8xx: Add missing Guarded setting in DTLB Error.
powerpc/8xx: Fixup DAR from buggy dcbX instructions.
powerpc/8xx: Tag DAR with 0x00f0 to catch buggy instructions.
powerpc/8xx: Update TLB asm so it behaves as linux mm expects.
powerpc/8xx: Invalidate non present TLBs
powerpc/pseries: Serialize cpu hotplug operations during deactivate Vs deallocate
pseries/pseries: Add code to online/offline CPUs of a DLPAR node
powerpc: stop_this_cpu: remove the cpu from the online map.
powerpc/pseries: Add kernel based CPU DLPAR handling
sysfs/cpu: Add probe/release files
powerpc/pseries: Kernel DLPAR Infrastructure
...
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (189 commits)
drm/radeon/kms: fix warning about cur_placement being uninitialised.
drm/ttm: Print debug information on memory manager when eviction fails
drm: Add memory manager debug function
drm/radeon/kms: restore surface registers on resume.
drm/radeon/kms/r600/r700: fallback gracefully on ucode failure
drm/ttm: Initialize eviction placement in case the driver callback doesn't
drm/radeon/kms: cleanup structure and module if initialization fails
drm/radeon/kms: actualy set the eviction placements we choose
drm/radeon/kms: Fix NULL ptr dereference
drm/radeon/kms/avivo: add support for new pll selection algo
drm/radeon/kms/avivo: fix some bugs in the display bandwidth setup
drm/radeon/kms: fix return value from fence function.
drm/radeon: Remove tests for -ERESTART from the TTM code.
drm/ttm: Have the TTM code return -ERESTARTSYS instead of -ERESTART.
drm/radeon/kms: Convert radeon to new TTM validation API (V2)
drm/ttm: Rework validation & memory space allocation (V3)
drm: Add search/get functions to get a block in a specific range
drm/radeon/kms: fix avivo tiling regression since radeon object rework
drm/i915: Remove a debugging printk from hangcheck
drm/radeon/kms: make sure i2c id matches
...
* 'bkl-drivers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
agp: Remove the BKL from agp_open
inifiband: Remove BKL from ipath_open()
mips: Remove BKL from tb0219
drivers: Remove BKL from scx200_gpio
drivers: Remove BKL from pc8736x_gpio
parisc: Remove BKL from eisa_eeprom
rtc: Remove BKL from efirtc
input: Remove BKL from hp_sdc_rtc
hw_random: Remove BKL from core
macintosh: Remove BKL from ans-lcd
nvram: Drop the bkl from non-generic nvram_llseek()
nvram: Drop the bkl from nvram_llseek()
mem_class: Drop the bkl from memory_open()
spi: Remove BKL from spidev_open
drivers: Remove BKL from cs5535_gpio
drivers: Remove BKL from misc_open
This merges the upstream Intel tree and fixes up numerous conflicts
due to patches merged into Linus tree later in -rc cycle.
Conflicts:
drivers/char/agp/intel-agp.c
drivers/gpu/drm/drm_dp_i2c_helper.c
drivers/gpu/drm/i915/i915_irq.c
drivers/gpu/drm/i915/i915_suspend.c
Some BIOSes fail to initialise the GTT, which will cause DMA faults when
the IOMMU is enabled. We need to clear the whole thing to point at the
scratch page, not just the part that Linux is going to use.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
[anholt: Note that this may also help with stability in the presence of
driver bugs, by not drawing to memory we don't own]
Signed-off-by: Eric Anholt <eric@anholt.net>
IGD* isn't a useful name. Replace with the codenames, as sourced
from pci.ids.
Signed-off-by: Adam Jackson <ajax@redhat.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
* 'core-iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (63 commits)
x86, Calgary IOMMU quirk: Find nearest matching Calgary while walking up the PCI tree
x86/amd-iommu: Remove amd_iommu_pd_table
x86/amd-iommu: Move reset_iommu_command_buffer out of locked code
x86/amd-iommu: Cleanup DTE flushing code
x86/amd-iommu: Introduce iommu_flush_device() function
x86/amd-iommu: Cleanup attach/detach_device code
x86/amd-iommu: Keep devices per domain in a list
x86/amd-iommu: Add device bind reference counting
x86/amd-iommu: Use dev->arch->iommu to store iommu related information
x86/amd-iommu: Remove support for domain sharing
x86/amd-iommu: Rearrange dma_ops related functions
x86/amd-iommu: Move some pte allocation functions in the right section
x86/amd-iommu: Remove iommu parameter from dma_ops_domain_alloc
x86/amd-iommu: Use get_device_id and check_device where appropriate
x86/amd-iommu: Move find_protection_domain to helper functions
x86/amd-iommu: Simplify get_device_resources()
x86/amd-iommu: Let domain_for_device handle aliases
x86/amd-iommu: Remove iommu specific handling from dma_ops path
x86/amd-iommu: Remove iommu parameter from __(un)map_single
x86/amd-iommu: Make alloc_new_range aware of multiple IOMMUs
...
We should set this before calling agp_add_bridge() so that it's done
before we map the scratch page too.
This should probably fix the regression reported as k.o. bug #14627.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add new CPU host bridge id, needed for support Ironlake graphics
device with it. No change for graphics device itself, so no need to
update drm/i915.
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
The GART IOMMU code has no strong dependency to the AMD64
AGP code. So the automatic selection of AGP_AMD64 for GART
can be removed.
Cc: Dave Jones <davej@redhat.com>
Signed-off-by: Pavel Vasilyev <pavel@pavlinux.ru>
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
- Remove the BKL from agp_open
- Perform a few clean-ups.
Analysis:
---------
int minor is local to the function.
The following are protected by agp_fe.agp_mutex
struct agp_file_private *priv;
struct agp_client *client;
Call-outs:
kzalloc should be safe to call under the mutex_lock
agp_find_client_by_pid:
- agp_mmap calls that under agp_fe.agp_mutex which we hold in agp_open
- agpioc_reserve_wrap calls it without any locking what-so-ever.
- Is that an error? Or is that okay because it has pid that is
a unique handle?
agp_insert_file_private:
- This function only manipulates struct agp_file_private, once again
while agp_fe.agp_mutex is held
Signed-off-by: John Kacur <jkacur@redhat.com>
Acked-by: David Airlie <airlied@linux.ie>
LKML-Reference: <alpine.LFD.2.00.0910112216060.12574@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* mark struct vm_area_struct::vm_ops as const
* mark vm_ops in AGP code
But leave TTM code alone, something is fishy there with global vm_ops
being used.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-intel-next' of git://git.kernel.org/pub/scm/linux/kernel/git/anholt/drm-intel: (57 commits)
drm/i915: Handle ERESTARTSYS during page fault
drm/i915: Warn before mmaping a purgeable buffer.
drm/i915: Track purged state.
drm/i915: Remove eviction debug spam
drm/i915: Immediately discard any backing storage for uneeded objects
drm/i915: Do not mis-classify clean objects as purgeable
drm/i915: Whitespace correction for madv
drm/i915: BUG_ON page refleak during unbind
drm/i915: Search harder for a reusable object
drm/i915: Clean up evict from list.
drm/i915: Add tracepoints
drm/i915: framebuffer compression for GM45+
drm/i915: split display functions by chip type
drm/i915: Skip the sanity checks if the current relocation is valid
drm/i915: Check that the relocation points to within the target
drm/i915: correct FBC update when pipe base update occurs
drm/i915: blacklist Acer AspireOne lid status
ACPI: make ACPI button funcs no-ops if not built in
drm/i915: prevent FIFO calculation overflows on 32 bits with high dotclocks
drm/i915: intel_display.c handle latency variable efficiently
...
Fix up trivial conflicts in drivers/gpu/drm/i915/{i915_dma.c|i915_drv.h}
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux-acpi-2.6: (119 commits)
ACPI: don't pass handle for fixed hardware notifications
ACPI: remove null pointer checks in deferred execution path
ACPI: simplify deferred execution path
acerhdf: additional BIOS versions
acerhdf: convert to dev_pm_ops
acerhdf: fix fan control for AOA150 model
thermal: add missing Kconfig dependency
acpi: switch /proc/acpi/{debug_layer,debug_level} to seq_file
hp-wmi: fix rfkill memory leak on unload
ACPI: remove unnecessary #ifdef CONFIG_DMI
ACPI: linux/acpi.h should not include linux/dmi.h
hwmon driver for ACPI 4.0 power meters
topstar-laptop: add new driver for hotkeys support on Topstar N01
thinkpad_acpi: fix rfkill memory leak on unload
thinkpad-acpi: report brightness events when required
thinkpad-acpi: don't poll by default any of the reserved hotkeys
thinkpad-acpi: Fix procfs hotkey reset command
thinkpad-acpi: deprecate hotkey_bios_mask
thinkpad-acpi: hotkey poll fixes
thinkpad-acpi: be more strict when detecting a ThinkPad
...
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (34 commits)
trivial: fix typo in aic7xxx comment
trivial: fix comment typo in drivers/ata/pata_hpt37x.c
trivial: typo in kernel-parameters.txt
trivial: fix typo in tracing documentation
trivial: add __init/__exit macros in drivers/gpio/bt8xxgpio.c
trivial: add __init macro/ fix of __exit macro location in ipmi_poweroff.c
trivial: remove unnecessary semicolons
trivial: Fix duplicated word "options" in comment
trivial: kbuild: remove extraneous blank line after declaration of usage()
trivial: improve help text for mm debug config options
trivial: doc: hpfall: accept disk device to unload as argument
trivial: doc: hpfall: reduce risk that hpfall can do harm
trivial: SubmittingPatches: Fix reference to renumbered step
trivial: fix typos "man[ae]g?ment" -> "management"
trivial: media/video/cx88: add __init/__exit macros to cx88 drivers
trivial: fix typo in CONFIG_DEBUG_FS in gcov doc
trivial: fix missing printk space in amd_k7_smp_check
trivial: fix typo s/ketymap/keymap/ in comment
trivial: fix typo "to to" in multiple files
trivial: fix typos in comments s/DGBU/DBGU/
...
Sizing of memory allocations shouldn't depend on the number of physical
pages found in a system, as that generally includes (perhaps a huge amount
of) non-RAM pages. The amount of what actually is usable as storage
should instead be used as a basis here.
Some of the calculations (i.e. those not intending to use high memory)
should likely even use (totalram_pages - totalhigh_pages).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Acked-by: Rusty Russell <rusty@rustcorp.com.au>
Acked-by: Ingo Molnar <mingo@elte.hu>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Hugh Dickins <hugh.dickins@tiscali.co.uk>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Patrick McHardy <kaber@trash.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (134 commits)
powerpc/nvram: Enable use Generic NVRAM driver for different size chips
powerpc/iseries: Fix oops reading from /proc/iSeries/mf/*/cmdline
powerpc/ps3: Workaround for flash memory I/O error
powerpc/booke: Don't set DABR on 64-bit BookE, use DAC1 instead
powerpc/perf_counters: Reduce stack usage of power_check_constraints
powerpc: Fix bug where perf_counters breaks oprofile
powerpc/85xx: Fix SMP compile error and allow NULL for smp_ops
powerpc/irq: Improve nanodoc
powerpc: Fix some late PowerMac G5 with PCIe ATI graphics
powerpc/fsl-booke: Use HW PTE format if CONFIG_PTE_64BIT
powerpc/book3e: Add missing page sizes
powerpc/pseries: Fix to handle slb resize across migration
powerpc/powermac: Thermal control turns system off too eagerly
powerpc/pci: Merge ppc32 and ppc64 versions of phb_scan()
powerpc/405ex: support cuImage via included dtb
powerpc/405ex: provide necessary fixup function to support cuImage
powerpc/40x: Add support for the ESTeem 195E (PPC405EP) SBC
powerpc/44x: Add Eiger AMCC (AppliedMicro) PPC460SX evaluation board support.
powerpc/44x: Update Arches defconfig
powerpc/44x: Update Arches dts
...
Fix up conflicts in drivers/char/agp/uninorth-agp.c
* 'agp-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp/intel: remove restore in resume
agp: fix uninorth build
intel-agp: Set dma mask for i915
agp: kill phys_to_gart() and gart_to_phys()
intel-agp: fix sglist allocation to avoid vmalloc()
intel-agp: Move repeated sglist free into separate function
agp: Switch agp_{un,}map_page() to take struct page * argument
agp: tidy up handling of scratch pages w.r.t. DMA API
intel_agp: Use PCI DMA API correctly on chipsets new enough to have IOMMU
agp: Add generic support for graphics dma remapping
agp: Switch mask_memory() method to take address argument again, not page
As early pci resume has already restored config for host
bridge and graphics device, don't need to restore it again,
This removes an original order hack for graphics device restore.
This fixed the resume hang issue found by Alan Stern on 845G,
caused by extra config restore on graphics device.
Cc: Stable Team <stable@kernel.org>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Ever since we enabled GEM, the pre-9xx chipsets (particularly 865) have had
serious stability issues. Back in May a wbinvd was added to the DRM to
work around much of the problem. Some failure remained -- easily visible
by dragging a window around on an X -retro desktop, or by looking at bugzilla.
The chipset flush was on the right track -- hitting the right amount of
memory, and it appears to be the only way to flush on these chipsets, but the
flush page was mapped uncached. As a result, the writes trying to clear the
writeback cache ended up bypassing the cache, and not flushing anything! The
wbinvd would flush out other writeback data and often cause the data we wanted
to get flushed, but not always. By removing the setting of the page to UC
and instead just clflushing the data we write to try to flush it, we get the
desired behavior with no wbinvd.
This exports clflush_cache_range(), which was laying around and happened to
basically match the code I was otherwise going to copy from the DRM.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Brice Goglin <Brice.Goglin@ens-lyon.org>
Cc: stable@kernel.org
New variant of IGDNG mobile chip has new host bridge id.
[anholt: Note that this new PCI ID doesn't impact the DRM, which doesn't
care about the PCI ID of the bridge]
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Completed a major update for the acpi_get_object_info external interface.
Changes include:
- Support for variable, unlimited length HID, UID, and CID strings
- Support Processor objects the same as Devices (HID,UID,CID,ADR,STA, etc.)
- Call the _SxW power methods on behalf of a device object
- Determine if a device is a PCI root bridge
- Change the ACPI_BUFFER parameter to ACPI_DEVICE_INFO.
These changes will require an update to all callers of this interface.
See the ACPICA Programmer Reference for details.
Also, update all invocations of acpi_get_object_info interface
Signed-off-by: Bob Moore <robert.moore@intel.com>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
Map the GART table uncached, so we don't always need to flush the CPU caches
explicitly after updates.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Using the radeon KMS test functionality, I verified that the AGP bridge of the
Intrepid2 chipset in my PowerBook supports aperture sizes up to 256M. So allow
aperture sizes up to 256M on pre-U3 bridges as well, and bump the default size
to 256M. It's possible that older revisions only support smaller sizes, but
it'll be easy to verify that with the raden KMS test functionality. Also,
there's only a problem on an actual attempt to access the aperture beyond the
maximum size supported by the hardware, and non-KMS X still defaults to using
only 32M.
Also use ARRAY_SIZE for the aperture size arrays.
Signed-off-by: Michel Dänzer <daenzer@vmware.com>
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
If DMAR is configured in but absent, we really do want to make sure that
the dma mask is set appropriately. Otherwise we get mapping failures on
highmem. Spotted by Zhenyu Wang.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
When graphics dma remapping engine is active, we must fill
gart table with dma address from dmar engine, as now graphics
device access to graphics memory must go through dma remapping
table to get real physical address.
Add this support to all drivers which use intel_i915_insert_entries()
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
New driver hooks for support graphics memory dma remapping
are introduced in this patch. It makes generic code can
tell if current device needs dma remapping, then call driver
provided interfaces for mapping and unmapping. Change has
also been made to handle scratch_page in remapping case.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
In commit 07613ba2 ("agp: switch AGP to use page array instead of
unsigned long array") we switched the mask_memory() method to take a
'struct page *' instead of an address. This is painful, because in some
cases it has to be an IOMMU-mapped virtual bus address (in fact,
shouldn't it _always_ be a dma_addr_t returned from pci_map_xxx(), and
we just happen to get lucky most of the time?)
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Fix those compiler warnings, which indeed point to a bug:
drivers/char/agp/parisc-agp.c:228: warning: initialization from incompatible pointer type
drivers/char/agp/parisc-agp.c:201: warning: 'parisc_agp_page_mask_memory' defined but not used
Signed-off-by: Helge Deller <deller@gmx.de>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (24 commits)
agp/intel: Make intel_i965_mask_memory use dma_addr_t for physical addresses
agp: add user mapping support to ATI AGP bridge.
drm/i915: enable GEM on PAE.
drm/radeon: fix unused variables warning
agp: switch AGP to use page array instead of unsigned long array
agpgart: detected ALi M???? chipset with M1621
drm/radeon: command stream checker for r3xx-r5xx hardware
drm/radeon: Fully initialize LVDS info also when we can't get it from the ROM.
radeon: Fix CP byte order on big endian architectures with KMS.
agp/uninorth: Handle user memory types.
drm/ttm: Add some powerpc cache flush code.
radeon: Enable modesetting on non-x86.
drm/radeon: Respect AGP cant_use_aperture flag.
drm: EDID endianness fixes.
drm/radeon: this VRAM vs aperture test is wrong, just remove it.
drm/ttm: fix an error path to exit function correctly
drm: Apply "Memory fragmentation from lost alignment blocks"
ttm: Return -ERESTART when a signal interrupts bo eviction.
drm: Remove memory debugging infrastructure.
drm/i915: Clear fence register on tiling stride change.
...
Otherwise, the high bits to be stuffed in the unused lower bits of the
page address are lost.
Signed-off-by: Pierre Willenbrock <pierre@pirsoft.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
This switches AGP to use an array of pages for tracking the
pages allocated to the GART. This should enable GEM on PAE to work
a lot better as we can pass highmem pages to the PAT code and it will
do the right thing with them.
Signed-off-by: Dave Airlie <airlied@redhat.com>
Add M1621 chipset name to ali-agp, preventing "Detected ALi M???? chipset"
message.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It is generally agreed that it would be beneficial for u64 to be an
unsigned long long on all architectures. ia64 (in common with several
other 64-bit architectures) currently uses unsigned long. Migrating
piecemeal is too painful; this giant patch fixes all compilation warnings
and errors that come as a result of switching to use int-ll64.h.
Note that userspace will still see __u64 defined as unsigned long. This
is important as it affects C++ name mangling.
[Updated by Tony Luck to change efi.h:efi_freemem_callback_t to use
u64 for start/end rather than unsigned long]
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Tony Luck <tony.luck@intel.com>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
agp: zero pages before sending to userspace
drm: check for minor master before allowing drop master.
drm: set/clear is_master when master changed
drm: clean dirty memory after device release
drm: count reaches -1
AGP pages might be mapped into userspace finally, so the pages should be
set to zero before userspace can use it. Otherwise there is potential
information leakage.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Support the Intel 854 Chipset in fbdev.
We test and use the patch on a Thomson IP1101 IPTV-Box. On the VGA-Port
we get a normal signal.
Here is the link to the Mambux-Project: http://www.mambux.de
Cc: Keith Packard <keithp@keithp.com>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Krzysztof Helt <krzysztof.h1@poczta.fm>
Signed-off-by: Stefan Husemann <shusemann@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
commit 11c3b5c3e0
Author: Greg Kroah-Hartman <gregkh@suse.de>
Date: Tue Dec 16 12:24:56 2008 -0800
driver core: move klist_children into private structure
Broke our parisc build pretty badly because we touch the klists directly
in three cases (AGP, SBA and GSC). Although GregKH will revert this
patch, there's no reason we should be using the iterators directly, we
can just move to the standard device_for_each_child() API.
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Tested-by: Helge Deller <deller@gmx.de>
Tested-by: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
When GTT size is equal to amount of video memory, the amount of GTT
entries is computed lower than zero, which is invalid and leads to
off-by-one error in intel_i915_configure()
Originally posted here:
http://bugzilla.kernel.org/show_bug.cgi?id=12539http://bugzilla.redhat.com/show_bug.cgi?id=445592
Signed-off-by: Lubomir Rintel <lkundrak@v3.sk>
Cc: Lubomir Rintel <lkundrak@v3.sk>
Cc: Dave Airlie <airlied@linux.ie>
Reviewed-by: Eric Anholt <eric@anholt.net>
Cc: <stable@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Impact: fix bug to make agp work with dri
Jeffrey reported that dri does work with 64bit, but doesn't work with
32bit it turns out NB aperture is 32M, aperture on agp is 128M
64bit is using 64M for vaidation for 64 iommu/gart 32bit is only using
32M..., and will not update the nb aperture.
So try to compare nb apterture and agp apterture before leaving not
touch nb aperture.
Reported-by: Jeffrey Trull <jetrull@sbcglobal.net>
Tested-by: Jeffrey Trull <jetrull@sbcglobal.net>
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Dave Airlie <airlied@linux.ie>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'aperture' is declared devinitdata (the whole word of it) and
is used from ->fetch_size() which can, AFAICS, be used on
!HOTPLUG after init time.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update assorted email addresses and related info to point
to a single current, valid address.
additionally
- trivial CREDITS entry updates. (Not that this file means much any more)
- remove arjans dead redhat.com address from powernow driver
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'agp-next' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp/nvidia: Support agp user-memory on nvidia agp.
agp/amd-k7: Suspend support for AMD K7 GART driver
agp/intel: Reduce extraneous PCI posting reads during init
agp: Fix stolen memory counting on G4X.
Reinitialize bridge registers after suspend, but avoid repeating the ioremap
Tested and works on AMD761
Signed-off-by: Stuart Bennett <stuart@freedesktop.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Instead of doing a posting read after each GTT entry update, do a single one
at the end of the writes. This should reduce boot time a tiny amount by
avoiding a lot of extra uncached reads.
Signed-off-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On the GM45, the amount of stolen memory mapped to the GTT was underestimated,
even though we had 508KB more available since the GTT doesn't take from
stolen memory. On the non-GM45 G4X, we overestimated how much stolen was
mapped to the GTT by 4KB, resulting in GPU page faults when that page was
accessed.
This update requires a corresponding update to xf86-video-intel to work
correctly.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The pageattr-array patch that you currently have in tip/master only
enables it for intel-agp, not the others. The attached enables it for
all drivers currently directly using agp_generic_alloc_page() and
agp_generic_destroy_page() (ocal driver is amd-k7-agp).
The new agp_generic_alloc_pages() interface uses the also new
pageattr array interface API. This makes all AGP drivers that
up to now used generic_{alloc,destroy}_page() use it.
Signed-off-by: Rene Herman <rene.herman@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
To reduce tlb/cache flush, makes agp memory allocation do one flush
after all pages in a region are changed to uc.
All agp drivers except agp-sgi uses agp_generic_alloc_page()
for .agp_alloc_page, so the patch should work for them. agp-sgi is only
for ia64, so not a problem too.
Signed-off-by: Shaohua Li <shaohua.li@intel.com>
Cc: airlied@linux.ie
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The correct id is the id of the main host (5591) not
the id of the PCI-to-PCI bridge AGP (0001).
Output from "lspci -nv" shows that only the former
has AGP capabilities flag set:
00:00.0 0600: 1039:5591 (rev 02)
Flags: bus master, medium devsel, latency 64
Memory at ec000000 (32-bit, non-prefetchable) [size=32M]
Capabilities: [c0] AGP version 1.0
00:02.0 0604: 1039:0001 (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: eb500000-eb5fffff
Prefetchable memory behind bridge: eb300000-eb3fffff
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Dave Airlie <airlied@redhat.com>
On my Intel chipset (965GM), the GTT is entirely erased across
suspend/resume. This patch simply re-plays the current mapping at resume
time to restore the table.=20
I noticed this once I started relying on persistent GTT mappings across VT
switch in our GEM work -- the old X server and DRM code carefully unbind
all memory from the GTT on VT switch, but GEM does not bother.
I placed the list management and rewrite code in the generic layer on the
assumption that it will be needed on other hardware, but I did not add the
rewrite call to anything other than the Intel resume function.
Keep a list of current GATT mappings. At resume time, rewrite them into
the GATT. This is needed on Intel (at least) as the entire GATT is
cleared across suspend/resume.
[akpm@linux-foundation.org: coding-style fixes]
Signed-off-by: Keith Packard <keithp@keithp.com>
Cc: Dave Jones <davej@codemonkey.org.uk>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Convert printks to use dev_printk().
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
I think the intent was that if no bridges matched agp_amd64_pci_table[],
we would fall back to checking for any bridge with the AGP capability.
But in the current code, we execute the fallback path only when
pci_register_driver() itself fails, which is unrelated to whether any
matching devices were found.
This patch counts the AGP bridges found in the probe() method and executes
the fallback path when none is found.
Signed-off-by: Bjorn Helgaas <bjorn.helgaas@hp.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Cc: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
It's not even passed on to smp_call_function() anymore, since that
was removed. So kill it.
Acked-by: Jeremy Fitzhardinge <jeremy.fitzhardinge@citrix.com>
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
This adds missing stolen memory size detect for IGD_GM, be sure to
detect right size as current X intel driver (2.3.2) which has already
worked out.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
besides it apparently being useful only in 2.6.24 (the changes in 2.6.25
really mean that it could be converted back to a single-stage mechanism),
I'm seeing an issue in Xen Dom0 kernels, which is caused by the calling
of gart_to_virt() in the second stage invocations of the destroy function.
I think that besides this being a real issue with Xen (where
unmap_page_from_agp() is not just a page table attribute change), this
also is invalid from a theoretical perspective: One should not assume that
gart_to_virt() is still valid after unmapping a page. So minimally (keeping
the 2-stage mechanism) a patch like the one below would be needed.
Jan
Signed-off-by: Dave Airlie <airlied@redhat.com>
add a new PCI ID and remove an old dodgy one, include the explaination
in the commented code so nobody readds later.
(davej also sent the pci id addition).
Signed-off-by: Dave Airlie <airlied@redhat.com>
Cleanup gart handling on amd64 a bit: move common code into
enable_gart_translation , and use symbolic register names where
appropriate.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
some systems are using 32M for gart and agp when memory is less than 4G.
Kernel will reject and try to allcate another 64M that is not needed,
and we will waste 64M of perfectly good RAM.
this patch adds a workaround by checking aper_base/order between NB and
agp bridge. If they are the same, and memory size is less than 4G, it
will allow it.
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
while looking at Rafael J. Wysocki's system boot log,
I found a funny printout:
Node 0: aperture @ de000000 size 32 MB
Aperture too small (32 MB)
AGP bridge at 00:04:00
Aperture from AGP @ de000000 size 4096 MB (APSIZE 0)
Aperture too small (0 MB)
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 4000000
...
agpgart: Detected AGP bridge 20
agpgart: Aperture pointing to RAM
agpgart: Aperture from AGP @ de000000 size 4096 MB
agpgart: Aperture too small (0 MB)
agpgart: No usable aperture found.
agpgart: Consider rebooting with iommu=memaper=2 to get a good aperture.
it means BIOS allocated the correct gart on the NB and AGP bridge, but
because a bug in the silicon (the agp bridge reports the wrong order,
it wants 4G instead) the kernel will reject that allocation.
Also, because the size is only 32MB, and we try to get another 64M for gart,
late fix_northbridge can not revert that change because it still reads
the wrong size from agp bridge.
So try to double check the order value from the agp bridge, before calling
aperture_valid().
[ mingo@elte.hu: 32-bit fix. ]
Signed-off-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move symbolic constants into gart.h, and use them instead of hardcoded
constant.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
__FUNCTION__ is gcc-specific, use __func__
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
As of now, agp_compat_ioctl already runs without the BKL. Mutual exclusion
is enforced by agp_fe.agp_mutex in agp_ioctl() and agp_compat_ioctl().
Apply the same locking rationale to the two functions allowing BKL cleanup.
Signed-off-by: Mathieu Segaud <mathieu.segaud@regala.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Introduced between 2.6.25-rc2 and -rc3
drivers/char/agp/amd-k7-agp.c:439:6: warning: symbol 'cap_ptr' shadows an
earlier one
drivers/char/agp/amd-k7-agp.c:414:5: originally declared here
cap_ptr is never used again in this function, don't bother redeclaring.
Signed-off-by: Harvey Harrison <harvey.harrison@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Several AGP drivers right now use ioremap_nocache() on kernel ram in order
to turn a page of regular memory uncached.
There are two problems with this:
1) This is a total nightmare for the ioremap() implementation to keep
various mappings of the same page coherent.
2) It's a total nightmare for the AGP code since it adds a ton of
complexity in terms of keeping track of 2 different pointers to
the same thing, in terms of error handling etc etc.
This patch fixes this by making the AGP drivers use the new
set_memory_XX APIs instead.
Note: amd-k7-agp.c is built on Alpha too, and generic.c is built
on ia64 as well, which do not yet have the set_memory_*() APIs,
so for them some we have a few ugly #ifdefs - hopefully they'll
be fixed soon.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Dave Airlie <airlied@linux.ie>
* 'agp-patches' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/agp-2.6:
agp: remove flush_agp_mappings calls from new flush handling code
intel-agp: introduce IS_I915 and do some cleanups..
[intel_agp] fix name for G35 chipset
intel-agp: fixup resource handling in flush code.
intel-agp: add new chipset ID
agp: remove unnecessary pci_dev_put
agp: remove uid comparison as security check
fix AGP warning
agp/intel: Add chipset flushing support for i8xx chipsets.
intel-agp: add chipset flushing support
agp: add chipset flushing support to AGP interface
Convert AGP alpha driver from nopage to fault.
NULL is NOPAGE_SIGBUS, so we aren't changing behaviour there.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Change origin chipset name i965G_1 to market name G35.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
The flush code resource handling was having problems where some BIOS
reserve the resource in a pnp block and some don't.
Also there was a bug in that configure was being called at resume
and resetting some of the structs.
Signed-off-by: Dave Airlie <airlied@linux.ie>
This one adds new pci ids for Intel intergrated graphics chipset, with gtt
table access change on it and new gtt table size definition.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
pci_get_class implicitly does a pci_dev_put on its second argument, so
pci_dev_put is only needed if there is a break out of the loop.
The semantic match detecting this problem is as follows:
// <smpl>
@@
expression dev;
expression E;
@@
* pci_dev_put(dev)
... when != dev = E
(
* pci_get_device(...,dev)
|
* pci_get_device_reverse(...,dev)
|
* pci_get_subsys(...,dev)
|
* pci_get_class(...,dev)
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
In the face of containers and user namespaces, a uid==0 check for
security is not safe. Switch to a capability check.
I'm not sure I picked the right capability, but this being AGP
CAP_SYS_RAWIO seemed to make sense.
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
drivers/char/agp/intel-agp.c: In function 'intel_i965_g33_setup_chipset_flush':
drivers/char/agp/intel-agp.c:872: warning: right shift count >= width of type
I wish the agp code wasn't written in a 10,000-column xterm :(
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@linux.ie>
This is a bit of a large hammer but it makes sure the chipset is flushed
by writing out 1k of data to an uncached page. We may be able to get better
information in the future on how to this better.
Signed-off-by: Dave Airlie <airlied@redhat.com>
This adds support for flushing the chipsets on the 915, 945, 965 and G33
families of Intel chips.
The BIOS doesn't seem to always allocate the BAR on the 965 chipsets
so I have to use pci resource code to create a resource
It adds an export for pcibios_align_resource.
This bumps the AGP interface to 0.103.
Certain Intel chipsets contains a global write buffer, and this can require
flushing from the drm or X.org to make sure all data has hit RAM before
initiating a GPU transfer, due to a lack of coherency with the integrated
graphics device and this buffer.
This just adds generic support to the AGP interfaces, a follow-on patch
will add support to the Intel driver to use this interface.
Signed-off-by: Dave Airlie <airlied@redhat.com>
The set_memory_* and set_pages_* family of API's currently requires the
callers to do a global tlb flush after the function call; forgetting this is
a very nasty deathtrap. This patch moves the global tlb flush into
each of the callers
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch converts various users of change_page_attr() to the new,
more intent driven set_page_*/set_memory_* API set.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The E7221 chipset is a 915 rebadged for the Intel server line.
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch renames the IOMMU config option to GART_IOMMU because in fact it
means the GART and not general support for an IOMMU on x86.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Acked-by: Muli Ben-Yehuda <muli@il.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Create an inline function for clflush(), with the proper arguments,
and use it instead of hard-coding the instruction.
This also removes one instance of hard-coded wbinvd, based on a patch
by Bauder de Oliveira Costa.
[ tglx: arch/x86 adaptation ]
Cc: Andi Kleen <andi@firstfloor.org>
Cc: Glauber de Oliveira Costa <gcosta@redhat.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
It's *wrong* to have
#define log2(n) ffz(~(n))
It should be *reversed*:
#define log2(n) flz(~(n))
or
#define log2(n) fls(n)
or just use
ilog2(n) defined in linux/log2.h.
This patch follows the last solution, recommended by Andrew Morton.
Cc: <linux-ext4@vger.kernel.org>
Cc: Mingming Cao <cmm@us.ibm.com>
Cc: Bjorn Helgaas <bjorn.helgaas@hp.com>
Cc: Chris Ahna <christopher.j.ahna@intel.com>
Cc: David Mosberger-Tang <davidm@hpl.hp.com>
Cc: Kyle McMartin <kyle@parisc-linux.org>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Fengguang Wu <wfg@mail.ustc.edu.cn>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Move AGP and DRM menus into the video graphics support menu.
They use 'menuconfig' so that they can all be disabled with
one selection.
Make the console menu use 'menuconfig' so that it can all be
disabled with one selection.
Make the frame buffer menu use 'menuconfig' so that it can all be
disabled with one selection.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Antonino Daplas <adaplas@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Coverity spotted a "use after free" bug in
drivers/char/agp/amd-k7-agp.c::amd_create_gatt_pages().
The problem is this:
If "entry = kzalloc(sizeof(struct amd_page_map), GFP_KERNEL);"
fails, then there's a loop in the function to free all entries
allocated so far and break out of the allocation loop. That in itself
is pretty sane, but then the (now freed) 'tables' is assigned to
amd_irongate_private.gatt_pages and 'retval' is set to -ENOMEM which
causes amd_free_gatt_pages(); to be called at the end of the function.
The problem with this is that amd_free_gatt_pages() will then loop
'amd_irongate_private.num_tables' times and try to free each entry in
tables[] - this is bad since tables has already been freed and
furthermore it will call kfree(tables) at the end - a double free.
This patch removes the freeing loop in amd_create_gatt_pages() and
instead relies entirely on the call to amd_free_gatt_pages() to free
everything we allocated in case of an error. It also sets
amd_irongate_private.num_tables to the actual number of entries
allocated instead of just using the value passed in from the caller -
this ensures that amd_free_gatt_pages() will only attempt to free
stuff that was actually allocated.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Airlie <airlied@redhat.com>
With Andi's clflush fixup, we were getting hangs on server exit, flushing the
mappings after freeing each page helped.
This showed up a race condition where the pages after being freed could be
reused before the agp mappings had been flushed. Flushing after each single
page is a bad thing for future drm work, so make the page destroy a two pass
unmapping all the pages, flushing the mappings, and then destroying the pages.
Signed-off-by: Dave Airlie <airlied@linux.ie>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
This reverts commit f443675aff, which
breaks horribly if you aren't running an unreleased xf86-video-intel
driver out of git.
Signed-off-by: Kyle McMartin <kyle@mcmartin.ca>
Cc: Dave Airlie <airlied@linux.ie>
Cc: Zhenyu Wang <zhenyu.z.wang@intel.com>
Acked-by: Keith Packard <keithp@keithp.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The mask on i830 should be 0x70 always, later chips 0xF0 should be okay.
Signed-off-by: Dave Airlie <airlied@linux.ie>
Acked-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Cc: Michael Haas <laga@laga.ath.cx>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
G33 has 1MB GTT table range. Fix GTT mapping in case like 512MB aperture
size.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
G33 GTT stolen memory is below graphics data stolen memory and be seperate,
so don't subtract it in stolen mem counting.
Signed-off-by: Zhenyu Wang <zhenyu.z.wang@intel.com>
Acked-by: Dave Airlie <airlied@linux.ie>
Cc: Dave Jones <davej@codemonkey.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
patchset against 2.6.23-rc3.
corrects missing ioremap return checks and balancing on iounmap calls, integrated changes per list
recommendations on the original set of patches..
Signed-off-by: Scott Thompson <postfail <at> hushmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
(This is a resend of a patch originally submitted on 24-Jul-2007 00:14)
Ok, this is something the coverity checker found (CID: 1813).
I'm not at all intimate with this code, so I'm not sure if this
attempt at a fix is correct (but at least it compiles).
Please look it over and NACK if bad or merge if good ;-)
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Fix some missing places to check with device id info, which
should probe the device gart correctly.
Signed-off-by: Wang Zhenyu <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
AGP should not need to lock pages. They are not protecting any race
because there is no lock_page calls, only SetPageLocked.
This is causing hangs with d00806b183.
Signed-off-by: Nick Piggin <npiggin@suse.de>
Signed-off-by: Dave Airlie <airlied@redhat.com>
Hi,
Coverity spotted a "use after free" bug in
drivers/char/agp/ati-agp.c::ati_create_gatt_pages().
The same one that was in
drivers/char/agp/amd-k7-agp.c::amd_create_gatt_pages()
The problem is this:
If "entry = kzalloc(sizeof(struct ati_page_map), GFP_KERNEL);"
fails, then there's a loop in the function to free all entries
allocated so far and break out of the allocation loop. That in itself
is pretty sane, but then the (now freed) 'tables' is assigned to
ati_generic_private.gatt_pages and 'retval' is set to -ENOMEM which
causes ati_free_gatt_pages(); to be called at the end of the function.
The problem with this is that ati_free_gatt_pages() will then loop
'ati_generic_private.num_tables' times and try to free each entry in
tables[] - this is bad since tables has already been freed and
furthermore it will call kfree(tables) at the end - a double free.
This patch removes the freeing loop in ati_create_gatt_pages() and
instead relies entirely on the call to ati_free_gatt_pages() to free
everything we allocated in case of an error. It also sets
ati_generic_private.num_tables to the actual number of entries
allocated instead of just using the value passed in from the caller -
this ensures that ati_free_gatt_pages() will only attempt to free
stuff that was actually allocated.
Note: I'm in no way intimate with this code and I have no way to
actually test this patch (besides compile test it), so while I've
tried to be careful in reading the code and make sure the patch
does the right thing an ACK from someone who actually knows the
code in-depth would be very much appreciated.
Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
Instead of all drivers reading pci config space to get the revision
ID, they can now use the pci_device->revision member.
This exposes some issues where drivers where reading a word or a dword
for the revision number, and adding useless error-handling around the
read. Some drivers even just read it for no purpose of all.
In devices where the revision ID is being copied over and used in what
appears to be the equivalent of hotpath, I have left the copy code
and the cached copy as not to influence the driver's performance.
Compile tested with make all{yes,mod}config on x86_64 and i386.
Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Acked-by: Dave Jones <davej@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Most of the AGP changes recently have been done in lock-step with
DRM updates, so it's probably easier to have airlied pushing
AGP changes at the same time he does DRM updates.
[Also remove my name from the boot messages.
Cautionary tale to others: Never do this, when computers
don't boot, people assume you're responsible even if 15
other subsystems initialised after yours. :-) ]
Signed-off-by: Dave Jones <davej@redhat.com>
Signed-off-by: Dave Airlie <airlied@linux.ie>
After i915 chip, GMCH has no AGP port. Origin bridge driver in device
table will try to access illegal regs like APBASE, APSIZE, etc. This
may cause problem.
So mark them as NULL in the table, we won't load if no IGD got detect
and bridge has no AGP port.
Signed-off-by: Wang Zhenyu <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This patch trys to fix device probe in two cases. First we should
correctly detect device if integrated graphics device is not enabled
or exists, like an add-in card is plugged. Second on some type of intel
GMCH, it might have multiple graphic chip models, like 945GME case, so
we should be sure the detect works through the whole table.
Signed-off-by: Wang Zhenyu <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
* master.kernel.org:/pub/scm/linux/kernel/git/davej/agpgart:
[AGPGART] intel_agp: Add support for G33, Q33 and Q35 chipsets
[AGPGART] intel_agp: add support for 945GME
[AGPGART] intel_agp: add support for 965GME/GLE
[AGPGART] intel_agp: use table for device probe
[AGPGART] intel_agp: cleanup intel private data
This patch adds pci ids for G33, Q33 and Q35 chips, and update with new
GTT size and stolen mem size detect method on these chips.
Signed-off-by: Wang Zhenyu <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Fixed issues noted by Christoph Hellwig, and I changed device table
scan a bit to allow the case that some models of graphics chips may
have same host bridge type. This type of chip will be added in the future.
This patch cleans up device probe function. Eric Anholt was the original author.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Wang Zhenyu <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Remove volatile type declare for IO mem variables.
A single private gart data is used by all drivers, this
makes it clean. Eric Anholt wrote the original patch.
Signed-off-by: Wang Zhenyu <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
First thing mm.h does is including sched.h solely for can_do_mlock() inline
function which has "current" dereference inside. By dealing with can_do_mlock()
mm.h can be detached from sched.h which is good. See below, why.
This patch
a) removes unconditional inclusion of sched.h from mm.h
b) makes can_do_mlock() normal function in mm/mlock.c
c) exports can_do_mlock() to not break compilation
d) adds sched.h inclusions back to files that were getting it indirectly.
e) adds less bloated headers to some files (asm/signal.h, jiffies.h) that were
getting them indirectly
Net result is:
a) mm.h users would get less code to open, read, preprocess, parse, ... if
they don't need sched.h
b) sched.h stops being dependency for significant number of files:
on x86_64 allmodconfig touching sched.h results in recompile of 4083 files,
after patch it's only 3744 (-8.3%).
Cross-compile tested on
all arm defconfigs, all mips defconfigs, all powerpc defconfigs,
alpha alpha-up
arm
i386 i386-up i386-defconfig i386-allnoconfig
ia64 ia64-up
m68k
mips
parisc parisc-up
powerpc powerpc-up
s390 s390-up
sparc sparc-up
sparc64 sparc64-up
um-x86_64
x86_64 x86_64-up x86_64-defconfig x86_64-allnoconfig
as well as my two usual configs.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
there is a wrong id in drivers/char/agp/via-agp.c
#define PCI_DEVICE_ID_VIA_CX700 0x8324
It must be 0x0324
Notice that PCI_DEVICE_ID_VIA_CX700 is also used in
drivers/i2c/busses/i2c-viapro.c and
drivers/ide/pci/via82cxxx.c
So, I think that constant must be renamed to avoid conflicting.
I attached a proposed patch.
Signed-off-by: Dave Jones <davej@redhat.com>
I'm using a custom BIOS to configure the northbridge GART at address
0x80000000, size 2G. Linux complains:
"Aperture from northbridge cpu 0 beyond 4GB. Ignoring."
I think there's an off-by-two error in arch/x86_64/kernel/aperture.c:
AK: use correct types for i386
Signed-off-by: Andi Kleen <ak@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'for-linus' of git://one.firstfloor.org/home/andi/git/linux-2.6: (231 commits)
[PATCH] i386: Don't delete cpu_devs data to identify different x86 types in late_initcall
[PATCH] i386: type may be unused
[PATCH] i386: Some additional chipset register values validation.
[PATCH] i386: Add missing !X86_PAE dependincy to the 2G/2G split.
[PATCH] x86-64: Don't exclude asm-offsets.c in Documentation/dontdiff
[PATCH] i386: avoid redundant preempt_disable in __unlazy_fpu
[PATCH] i386: white space fixes in i387.h
[PATCH] i386: Drop noisy e820 debugging printks
[PATCH] x86-64: Fix allnoconfig error in genapic_flat.c
[PATCH] x86-64: Shut up warnings for vfat compat ioctls on other file systems
[PATCH] x86-64: Share identical video.S between i386 and x86-64
[PATCH] x86-64: Remove CONFIG_REORDER
[PATCH] x86-64: Print type and size correctly for unknown compat ioctls
[PATCH] i386: Remove copy_*_user BUG_ONs for (size < 0)
[PATCH] i386: Little cleanups in smpboot.c
[PATCH] x86-64: Don't enable NUMA for a single node in K8 NUMA scanning
[PATCH] x86: Use RDTSCP for synchronous get_cycles if possible
[PATCH] i386: Add X86_FEATURE_RDTSCP
[PATCH] i386: Implement X86_FEATURE_SYNC_RDTSC on i386
[PATCH] i386: Implement alternative_io for i386
...
Fix up trivial conflict in include/linux/highmem.h manually.
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* master.kernel.org:/pub/scm/linux/kernel/git/gregkh/pci-2.6: (59 commits)
PCI: Free resource files in error path of pci_create_sysfs_dev_files()
pci-quirks: disable MSI on RS400-200 and RS480
PCI hotplug: Use menuconfig objects
PCI: ZT5550 CPCI Hotplug driver fix
PCI: rpaphp: Remove semaphores
PCI: rpaphp: Ensure more pcibios_add/pcibios_remove symmetry
PCI: rpaphp: Use pcibios_remove_pci_devices() symmetrically
PCI: rpaphp: Document is_php_dn()
PCI: rpaphp: Document find_php_slot()
PCI: rpaphp: Rename rpaphp_register_pci_slot() to rpaphp_enable_slot()
PCI: rpaphp: refactor tail call to rpaphp_register_slot()
PCI: rpaphp: remove rpaphp_set_attention_status()
PCI: rpaphp: remove print_slot_pci_funcs()
PCI: rpaphp: Remove setup_pci_slot()
PCI: rpaphp: remove a call that does nothing but a pointer lookup
PCI: rpaphp: Remove another wrappered function
PCI: rpaphp: Remve another call that is a wrapper
PCI: rpaphp: remove a function that does nothing but wrap debug printks
PCI: rpaphp: Remove un-needed goto
PCI: rpaphp: Fix a memleak; slot->location string was never freed
...
Convert code that allocs a struct pci_dev to use alloc_pci_dev().
Signed-off-by: Michael Ellerman <michael@ellerman.id.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Under CONFIG_DISCONTIGMEM, assuming that a !pfn_valid() implies all
subsequent pfn-s are also invalid is wrong. Thus replace this by
explicitly checking against the E820 map.
AK: make e820 on x86-64 not initdata
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Andi Kleen <ak@suse.de>
Acked-by: Mark Langsdorf <mark.langsdorf@amd.com>
These are all the remaining instances of get_property. Simple rename of
get_property to of_get_property.
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Paul Mackerras <paulus@samba.org>
Fix a call to __free_page where __free_pages(, 2) was meant, and do proper
error path handling. Also remove a redundant conditional.
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Remove an arch-dependent hunk in favor of #define-ing the respective bits in
asm-<arch>/agp.h (allowing easier overriding in para-virtualized environments).
Signed-off-by: Jan Beulich <jbeulich@novell.com>
Signed-off-by: Dave Jones <davej@redhat.com>
For some vendor/id pairs the kernel will autoload both the sis-agp and the
amd64_agp modules as the sis-agp module will load for all sis devices.
This collision causes the bug reported in:
http://bugzilla.novell.com/show_bug.cgi?id=248665
As currently sis_probe does its own matching, requesting the whole range
gains nothing. The clean fix seems to me to leave the matching to the core
and advertise only the devices actually supported. This patch does so.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
On G965, I810_PGETBL_CTL is a mmio offset, but we wrongly take it
as pci config space offset in detecting GTT size. This one line patch
fixs this.
Signed-off-by: Wang Zhenyu <zhenyu.z.wang@intel.com>
Signed-off-by: Dave Jones <davej@redhat.com>
This fixes the following compile failures of agpgart drivers.
These errors were inserted by the recent AGPGART constification patch.
drivers/char/agp/uninorth-agp.c:492: error: expected '{' before 'const'
drivers/char/agp/uninorth-agp.c:517: error: expected '{' before 'const'
drivers/char/agp/uninorth-agp.c: In function 'agp_uninorth_probe':
drivers/char/agp/uninorth-agp.c:634: error: 'u3_agp_driver' undeclared (first use in this function)
drivers/char/agp/uninorth-agp.c:634: error: (Each undeclared identifier is reported only once
drivers/char/agp/uninorth-agp.c:634: error: for each function it appears in.)
drivers/char/agp/uninorth-agp.c:636: error: 'uninorth_agp_driver' undeclared (first use in this function)
Signed-off-by: Ryusuke Konishi <ryusuke@osrg.net>
Signed-off-by: Dave Jones <davej@redhat.com>
Can't really blame davej for mucking this up... static-ify
it while we're at it, which would have prevented this...
Signed-off-by: Kyle McMartin <kyle@parisc-linux.org>
* master.kernel.org:/pub/scm/linux/kernel/git/kyle/parisc-2.6: (78 commits)
[PARISC] Use symbolic last syscall in __NR_Linux_syscalls
[PARISC] Add missing statfs64 and fstatfs64 syscalls
Revert "[PARISC] Optimize TLB flush on SMP systems"
[PARISC] Compat signal fixes for 64-bit parisc
[PARISC] Reorder syscalls to match unistd.h
Revert "[PATCH] make kernel/signal.c:kill_proc_info() static"
[PARISC] fix sys_rt_sigqueueinfo
[PARISC] fix section mismatch warnings in harmony sound driver
[PARISC] do not export get_register/set_register
[PARISC] add ENTRY()/ENDPROC() and simplify assembly of HP/UX emulation code
[PARISC] convert to use CONFIG_64BIT instead of __LP64__
[PARISC] use CONFIG_64BIT instead of __LP64__
[PARISC] add ASM_EXCEPTIONTABLE_ENTRY() macro
[PARISC] more ENTRY(), ENDPROC(), END() conversions
[PARISC] fix ENTRY() and ENDPROC() for 64bit-parisc
[PARISC] Fixes /proc/cpuinfo cache output on B160L
[PARISC] implement standard ENTRY(), END() and ENDPROC()
[PARISC] kill ENTRY_SYS_CPUS
[PARISC] clean up debugging printks in smp.c
[PARISC] factor syscall_restart code out of do_signal
...
Fix conflict in include/linux/sched.h due to kill_proc_info() being made
publicly available to PARISC again.
My previous compat AGP patch broke modular AGPGART.
Test built on;
i386 CONFIG_AGP=y,m
x86_64 CONFIG_AGP=y
ia64 CONFIG_AGP=m
Signed-off-by: Zwane Mwaikambo <zwane@infradead.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
Fix whitespace, braces, use kzalloc().
Cc: Dave Airlie <airlied@linux.ie>
Cc: Thomas Hellstrom <thomas@tungstengraphics.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Dave Jones <davej@redhat.com>
We don't unmap them on the suspend path, so on resume
trying to remap will fail, and then result in an
oops the next time something tries to access them.
Signed-off-by: Dave Jones <davej@redhat.com>
This patch allows drm to populate an agpgart structure with pages of its own.
It's needed for the new drm memory manager which dynamically flips pages in and out of AGP.
The patch modifies the generic functions as well as the intel agp driver. The intel drm driver is
currently the only one supporting the new memory manager.
Other agp drivers may need some minor fixing up once they have a corresponding memory manager enabled drm driver.
AGP memory types >= AGP_USER_TYPES are not populated by the agpgart driver, but the drm is expected
to do that, as well as taking care of cache- and tlb flushing when needed.
It's not possible to request these types from user space using agpgart ioctls.
The Intel driver also gets a new memory type for pages that can be bound cached to the intel GTT.
Signed-off-by: Thomas Hellstrom <thomas@tungstengraphics.com>
Signed-off-by: Dave Jones <davej@redhat.com>
Kulikov Vasiliy