Added a few more UDP tunnel APIs that can be shared by UDP based
tunnel protocol implementation. The main ones are highlighted below.
setup_udp_tunnel_sock() configures UDP listener socket for
receiving UDP encapsulated packets.
udp_tunnel_xmit_skb() and upd_tunnel6_xmit_skb() transmit skb
using UDP encapsulation.
udp_tunnel_sock_release() closes the UDP tunnel listener socket.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ip6_udp_tunnel.c for ipv6 UDP tunnel functions to avoid ifdefs
in udp_tunnel.c
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Li says:
====================
net: fec: add interrupt coalescence
improve error handle when parse queue number.
add interrupt coalescence feature.
Change from v2 to v3
- add error check in fec_enet_set_coalesce
- fix a run time warning to get clock rate in interrupt
- fix commit message use TKT number
Change from v1 to v2
- fix indention
- use errata number instead of TKT
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When enable three queues on imx6sx enet, and then do tx performance
test with iperf tool, after some time running, tx hang.
Found that:
If uDMA is running, software set TDAR may cause tx hang.
If uDMA is in idle, software set TDAR don't cause tx hang.
There is a TDAR race condition for mutliQ when the software sets TDAR
and the UDMA clears TDAR simultaneously or in a small window (2-4 cycles).
This will cause the udma_tx and udma_tx_arbiter state machines to hang.
The issue exist at i.MX6SX enet IP.
So, the Workaround is checking TDAR status four time, if TDAR cleared by
hardware and then write TDAR, otherwise don't set TDAR.
The patch is only one Workaround for the issue ERR007885.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
when enable interrupt coalesce, 8 BD is not enough.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6 SX support interrupt coalescence feature
By default, init the interrupt coalescing frame count threshold and
timer threshold.
Supply the ethtool interfaces as below for user tuning to improve
enet performance:
rx_max_coalesced_frames
rx_coalesce_usecs
tx_max_coalesced_frames
tx_coalesce_usecs
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
check tx and rx queue seperately.
fix typo, "Invalidate" and "fail".
change pr_err to pr_warn.
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 233577a220 ("net: filter: constify detection of pkt_type_offset")
allows us to implement simple PKTTYPE support in sparc JIT
Signed-off-by: Alexei Starovoitov <ast@plumgrid.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This ensures the tcf_exts_init() is called for all cases.
Fixes: 952313bd62 ("net: sched: cls_cgroup use RCU")
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pravin B Shelar says:
====================
Open vSwitch
Following patches adds recirculation and hash action to OVS.
First patch removes pointer to stack object. Next three patches
does code restructuring which is required for last patch.
Recirculation implementation is changed, according to comments from
David Miller, to avoid using recursive calls in OVS. It is using
queue to record recirc action and deferred recirc is executed at
the end of current actions execution.
v1-v2:
Changed subsystem name in subject to openvswitch
v2-v3:
Added patch to remove pkt_key pointer from skb->cb.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When allocating a new structure we also need to call tcf_exts_init
to initialize exts.
A follow up patch might be in order to remove some of this code
and do tcf_exts_assign(). With this we could remove the
tcf_exts_init/tcf_exts_change pattern for some of the classifiers.
As part of the future tcf_actions RCU series this will need to be
done. For now fix the call here.
Fixes e35a8ee599 ("net: sched: fw use RCU")
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tree: git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next.git master
head: 54996b529a
commit: c7953ef230 [625/646] net: sched: cls_cgroup use RCU
net/sched/cls_cgroup.c:130 cls_cgroup_change() warn: possible memory leak of 'new'
net/sched/cls_cgroup.c:135 cls_cgroup_change() warn: possible memory leak of 'new'
net/sched/cls_cgroup.c:139 cls_cgroup_change() warn: possible memory leak of 'new'
Fixes: c7953ef230 ("net: sched: cls_cgroup use RCU")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
kbuild test robot reported an unused variable cpu in cls_u32.c
after the patch below. This happens when PERF and MARK config
variables are disabled
Fix this is to use separate variables for perf and mark
and define the cpu variable inside the ifdef logic.
Fixes: 459d5f626d ("net: sched: make cls_u32 per cpu")'
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Cong Wang <cwang@twopensource.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: commit 331b72922c ("net: sched: RCU cls_tcindex")
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-By: John Fastabend <john.r.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Recirc action allows a packet to reenter openvswitch processing.
currently openvswitch lookup flow for packet received and execute
set of actions on that packet, with help of recirc action we can
process/modify the packet and recirculate it back in openvswitch
for another pass.
OVS hash action calculates 5-tupple hash and set hash in flow-key
hash. This can be used along with recirculation for distributing
packets among different ports for bond devices.
For example:
OVS bonding can use following actions:
Match on: bond flow; Action: hash, recirc(id)
Match on: recirc-id == id and hash lower bits == a;
Action: output port_bond_a
Signed-off-by: Andy Zhou <azhou@nicira.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
The current sample() function implementation is more complicated
than necessary in handling single user space action optimization
and skb reference counting. There is no functional changes.
Signed-off-by: Andy Zhou <azhou@nicira.com>
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Currently tun_key is used for passing tunnel information
on ingress and egress path, this cause confusion. Following
patch removes its use on ingress path make it egress only parameter.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Andy Zhou <azhou@nicira.com>
OVS flow extract is called on packet receive or packet
execute code path. Following patch defines separate API
for extracting flow-key in packet execute code path.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Acked-by: Andy Zhou <azhou@nicira.com>
OVS keeps pointer to packet key in skb->cb, but the packet key is
store on stack. This could make code bit tricky. So it is better to
get rid of the pointer.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
dsa_of_probe() still used cd->mii_bus instead of cd->host_dev when
building with CONFIG_OF=y. Fix this by making the replacement here as
well.
Fixes: b4d2394d01 ("dsa: Replace mii_bus with a generic host device")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: commit 331b72922c ("net: sched: RCU cls_tcindex")
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: commit 331b72922c ("net: sched: RCU cls_tcindex")
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fixes: commit 1f947bf151 ("net: sched: rcu'ify cls_bpf")
Cc: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Duyck says:
====================
DSA Cleanups
This patch series does two things, first it cleans up the tag_protocol and
protocol ops being configured seperately. Second it addresses the desire
to split DSA away from relying on a MII bus.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This change makes it so that instead of passing and storing a mii_bus we
instead pass and store a host_dev. From there we can test to determine the
exact type of device, and can verify it is the correct device for our switch.
So for example it would be possible to pass a device pointer from a pci_dev
and instead of checking for a PHY ID we could check for a vendor and/or device
ID.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change addresses several issues.
First, it was possible to set tag_protocol without setting the ops pointer.
To correct that I have reordered things so that rcv is now populated before
we set tag_protocol.
Second, it didn't make much sense to keep setting the device ops each time a
new slave was registered. So by moving the receive portion out into root
switch initialization that issue should be addressed.
Third, I wanted to avoid sending tags if the rcv pointer was not registered
so I changed the tag check to verify if the rcv function pointer is set on
the root tree. If it is then we start sending DSA tagged frames.
Finally I split the device ops pointer in the structures into two spots. I
placed the rcv function pointer in the root switch since this makes it
easiest to access from there, and I placed the xmit function pointer in the
slave for the same reason.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nikolay Aleksandrov says:
====================
bonding: style, comment and assertion changes
This is a small and simple patch-set that doesn't introduce (hopefully) any
functional changes, but only stylistic and semantic ones.
Patch 01 simply uses the already provided __rlb_next_rx_slave function inside
rlb_next_rx_slave(), thus removing the duplication of code.
Patch 02 changes all comments that I could find to netdev style, removes
some outdated ones and fixes a few more small cosmetic issues (new line
after declaration, braces around if; else and such)
Patch 03 removes one extra ASSERT_RTNL() because we already have it in the
parent function and consolidates two other ASSERT_RTNL()s to the function
that is exported and supposed to be called with RTNL anyway.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Consolidate the calls to ASSERT_RTNL() before bond_select_active_slave()
inside bond_select_active_slave() itself and remove the ASSERT_RTNL()
from bond_hw_addr_swap() as it's not exported and its only caller -
bond_change_active_slave() already has an ASSERT_RTNL().
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
First adjust a couple of locking comments that were left inaccurate,
then adjust comments to use the netdev styling and remove extra new
lines where necessary and add a couple of new lines between declarations
and code. These are all trivial styling changes, no functional change.
Also removed a couple of outdated or obvious comments.
This patch is by no means a complete fix of all netdev style violations
but it gets the bonding closer.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
__rlb_next_rx_slave() is a copy of rlb_next_rx_slave() with the
difference that it uses rcu primitives to walk the slave list. We don't
need the two functions and can make rlb_next_rx_slave() a wrapper for
callers which hold RTNL.
So add a comment and ASSERT_RTNL() to make sure what is intended.
Signed-off-by: Nikolay Aleksandrov <nikolay@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eric Dumazet says:
====================
tcp: no longer keep around headers in input path
Looking at tcp_try_coalesce() I was wondering why I did :
if (tcp_hdr(from)->fin)
return false;
The answer would be to allow the aggregation, if we simply OR the FIN and PSH
flags eventually present in @from to @to packet. (Note a change is also
needed in skb_try_coalesce() to avoid calling skb_put() with 0 len)
Then, looking at tcp_recvmsg(), I realized we access tcp_hdr(skb)->syn
(and maybe tcp_hdr(skb)->fin) for every packet we process from socket
receive queue.
We have to understand TCP flags are cold in cpu caches most of the time
(assuming TCP timestamps, and that application calls recvmsg() a long
time after incoming packet was processed), and bringing a whole
cache line only to access one bit is not very nice.
It would make sense to use in TCP input path TCP_SKB_CB(skb)->tcp_flags
as we do in output path.
This saves one cache line miss, and TCP tcp_collapse() can avoid dealing
with the headers.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_collapse() wants to shrink skb so that the overhead is minimal.
Now we store tcp flags into TCP_SKB_CB(skb)->tcp_flags, we no longer
need to keep around full headers.
Whole available space is dedicated to the payload.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We can allow a segment with FIN to be aggregated,
if we take care to add tcp flags,
and if skb_try_coalesce() takes care of zero sized skbs.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Input path of TCP do not currently uses TCP_SKB_CB(skb)->tcp_flags,
which is only used in output path.
tcp_recvmsg(), looks at tcp_hdr(skb)->syn for every skb found in receive queue,
and its unfortunate because this bit is located in a cache line right before
the payload.
We can simplify TCP by copying tcp flags into TCP_SKB_CB(skb)->tcp_flags.
This patch does so, and avoids the cache line miss in tcp_recvmsg()
Following patches will
- allow a segment with FIN being coalesced in tcp_try_coalesce()
- simplify tcp_collapse() by not copying the headers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Replacing strncpy with strlcpy to avoid strings that lacks null terminate.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use container_of instead of casting first structure member.
Compiled but untested.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use container_of instead of casting first structure member.
ARM cross-compiled but untested.
Signed-off-by: Fabian Frederick <fabf@skynet.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit "net: bpf: make eBPF interpreter images read-only" has changed bpf_prog
to be vmalloc()ed but never handled some of the errors paths of the old code.
On error within sk_attach_filter (which userspace can easily trigger), we'd
kfree() the vmalloc()ed memory, and leak the internal bpf_work_struct.
Signed-off-by: Sasha Levin <sasha.levin@oracle.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change corrects an error seen when DSA tagging is built as a module.
Without this change it is not possible to get XDSA tagged frames as the
test for tagging is stripped by the #ifdef check.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Print the IP revision when probing.
Signed-off-by: Bo Shen <voice.shen@atmel.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Frank Li says:
====================
net: fec: imx6sx multiqueue support
These patches enable i.MX6SX multi queue support.
i.MX6SX support 3 queue and AVB feature.
Change from v3 to v4
- use "unsigned int" instead of "unsigned"
Change from v2 to v3
- fixed alignment requirement for ARM and NO-ARM platform
Change from v1 to v2.
- Change num_tx_queue to unsigned int
- Avoid block non-dt platform
- remove call netif_set_real_num_rx_queues
- seperate multi queue patch two part, one is tx and rx handle, with fixed queue 0
then other one is initilized multiqueue
- use two difference alignment for tx and rx path
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch update fec devicetree binding doc that add Optional
properties "fsl,num-tx-queues" and "fsl,num-rx-queues".
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
i.MX6 SX change FEC alignment requirement.
i.MX6 SX change internal bus from AHB to AXI.
It require RX buffer must be 64 bytes alignment.
And remove TX buffer alignment requirement.
Signed-off-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Andy Zhou