Update defconfig to the latest kernel version
and enable the h1940 LED driver
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix the NAND flash timings on the AT91SAM9260.
The current timings lead to the detection of a number of bad blocks.
These timings are now set the same as on the AT91SAM9263.
Patch from Nicolas Ferre.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Added missing ifdefs, to make kernel linkable without the PM support.
Signed-off-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Build fix: sa1100/generic.c should already have included <asm/gpio.h>,
but it didn't ... causing a build problem with a recent patch.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
An iq80219 is a board with an iq31244 layout and an 80219 processor. It
breaks the current assumption that all 80219 processors run on ep80219
platforms. This patch adds the "force_ep80219" option to the kernel to
override boot loaders that have passed in the iq31244 id, and adds the
MACHINE_START definition for ep80219.
[ patch assumes that EP80219 has been added to mach-types ]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch corrects an error when demuxing the DMA irq's
DMA1 was used as a base and this should have been DMA0.
Without this fix we do not process DMA0 irq's and the
system effectively locks up in a loop trying the process
the irq it never can.
Signed-off-by: Graeme Gregory <gg@opensource.wolfsonmicro.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
It's been pointed out that output GPIOs should have an initial value, to
avoid signal glitching ... among other things, it can be some time before
a driver is ready. This patch corrects that oversight, fixing
- documentation
- platforms supporting the GPIO interface
- users of that call (just one for now, others are pending)
There's only one user of this call for now since most platforms are still
using non-generic GPIO setup code, which in most cases already couples the
initial value with its "set output mode" request.
Note that most platforms are clear about the hardware letting the output
value be set before the pin direction is changed, but the s3c241x docs are
vague on that topic ... so those chips might not avoid the glitches.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Andrew Victor <andrew@sanpeople.com>
Acked-by: Milan Svoboda <msvoboda@ra.rockwell.com>
Acked-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
72486f1f8f inverted the sense for
enabling hotplug CPU controls without reference to any other
architecture other than i386, ia64 and PowerPC. This left
everyone else without hotplug CPU control.
Fix ARM for this brain damage.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Only System PLL clock source is selectable by CSCR_SYSTEM_SEL
bit. MPU PLL is driven by 512*CLK32 for each case.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The minimal bus clock prescaler should be kept at value
selected by the board / boot loader designer.
Switching frequency above startup limit could
lead to the external memory/devices misbehave.
Signed-off-by: Pavel Pisa <pisa@cmp.felk.cvut.cz>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The sharpsl_pm code depends on some symbols in the APM emulation code.
Add the dependency for now until a better solution can be found.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Fix tosa compile failure from commit
32f3f49910
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The Product Manager of the cc9p insist on using the correct product names.
Signed-off-by: Uwe Kleine-König <ukleinek@informatik.uni-freiburg.de>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This adds the delayed application attribute to the dss2 clock. DSS2
can't select the 48MHz APLL with properly with out validating the
configuration as trigged by this flag.
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
ARM: OMAP: Fix missing #include <linux/workqueue.h> in
board-h2.c resulting in
In file included from arch/arm/mach-omap1/board-h2.c:40:
include/asm/arch/irda.h:27: error: field 'gpio_expa' has
incomplete type
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most drivers using GPIOs already know they are running on a system that
supports the generic GPIO calls, because of other platform dependencies.
But the generic GPIO-based LED and input button drivers can't know that.
So this patch adds a Kconfig hook, GENERIC_GPIO, to mark the platforms
where <asm/gpio.h> will do the right thing. Currently that's a bunch of
ARMs, and AVR32; more are on the way.
It also fixes a dependency bug for the gpio button input driver; it was
wrong to start with, now it covers all platforms with GENERIC_GPIO.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Acked-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Arnaud Patard <arnaud.patard@rtp-net.org>
Cc: <raph@8d.com>
Cc: <msvoboda@ra.rockwell.com>
Cc: pHilipp Zabel <philipp.zabel@gmail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Work around EBSA110 build errors by selecting NO_IOPORT. EBSA110
can't support an IO port to MMIO mapping mechanism because the
MMIO and IO port spaces have quite different and complex addressing
requirements.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update help text with location of documentation
and duplicate the note on the speed of CRC
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Always allow backtrace when using oprofile on ARM, even if a PMU
isn't present.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Convert 1510->15xx in generic omap code, so that sx1 can work.
Signed-off-by: Pavel Machek <pavel@suse.cz>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add missing includes to board-nokia770 to make it
compile again.
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
When I went to use dmtimer7 it did not seem to work. I noticed that
the base addresses for dmtimers 7 and 8 were set wrong. A simple patch
to correct a small error. Confirmed to fix the problem on an OSK.
Signed-off-by: Matthew Percival <matthew@capgo.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Some time ago, the 'lcd_lph8923' device was renamed to 'lcd_mipid' but
the board-nokia770.c file was not updated accordingly, leading to not
working lcd.
This one-liner fixe the trouble.
Signed-off-by: Arnaud Patard <arnaud.patard@rtp-net.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Teach OMAP2 gp timer that HZ isn't always 100.
Signed-off-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warning
arch/arm/mach-omap1/pm.c: In function 'omap_pm_init':
arch/arm/mach-omap1/pm.c:765: warning: ignoring return value
of 'subsys_create_file', declared with attribute
warn_unused_result
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warning
arch/arm/mach-omap2/timer-gp.c: In function
'omap2_gp_timer_init':
arch/arm/mach-omap2/timer-gp.c:70: warning: implicit
declaration of function 'setup_irq'
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warnings
arch/arm/plat-omap/dmtimer.c: In function
'omap_dm_timer_modify_idlect_mask':
arch/arm/plat-omap/dmtimer.c:317: warning: no return
statement in function returning non-void
arch/arm/plat-omap/mailbox.c: In function 'omap_mbox_init':
arch/arm/plat-omap/mailbox.c:231: warning: ignoring return
value of 'class_device_create_file', declared with attribute
warn_unused_result
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
No IRQF_TRIGGER set_type function for IRQ 353 (MPUIO)
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This makes serial usable also on omap310, not only 1510.
(changing 1510->15xx)
Signed-off-by: Marek Vašut <marek.vasut@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The register bits are reset by writing one. Remove the unneeded reads and
fix writes to not clear too many bits.
Signed-off-by: Timo Teras <timo.teras@solidboot.com>
Signed-off-by: Juha Yrjola <juha.yrjola@solidboot.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix warning:
arch/arm/mach-omap1/clock.c: In function
'omap1_clk_enable_generic':
arch/arm/mach-omap1/clock.c:499: warning: 'return' with no
value, in function returning non-void
Signed-off-by: Dirk Behme <dirk.behme_at_gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Disable accesses to SOFT_REQ_REG2 and ULPD_SOFT_DISABLE_REQ_REG
registers for 15xx processors that don't have these registers. Enable
level 2 interrupt handler for processors that identify as OMAP 15xx
(e.g 310) and not 1510 specifically. Also fix the following compiler
warning (only visible with CONFIG_OMAP_RESET_CLOCKS):
arch/arm/mach-omap1/clock.c: In function 'omap1_clk_disable_unused':
arch/arm/mach-omap1/clock.c:634: warning: 'return' with a value, in
function returning void
Signed-off-by: Andrzej Zaborowski <balrog@zabor.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
aware
Since TEXT_OFFSET is meant to determine RAM location for kernel use,
itshould affect .data and .bss initial mapping in the XIP case.
Otherwise a XIP kernel would crash if TEXT_OFFSET gets somewhat larger
than 2MB.
Corresponding code is also moved up a bit to be near the similar .text
mapping code making the whole a bit more straight forward to understand.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Since commit 2552fc27ff XIP kernels failed
to boot because (_end - PAGE_OFFSET - 1) is much smaller than the size
of the kernel text and data in the XIP case, causing the kernel not to
be entirely mapped.
Even in the non-XIP case, the use of (_end - PAGE_OFFSET - 1) is wrong
because it produces a too large value if TEXT_OFFSET is larger than 1MB.
Finally the original code was performing one loop too many.
Let's break the loop when the section pointer has passed the last byte
of the kernel instead.
Signed-off-by: Nicolas Pitre <nico@cam.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The new gpio_direction_input() and gpio_direction_output() functions
were both enabling output mode. When configuring a GPIO for input mode,
you need to program the ODR (Output Disable Register).
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The duplicate file "include/asm-arm/arch-at91rm9200/entry-macro.S" can
be removed - it was already moved to include/asm-arm/arch-at91/.
Fix 3 small typo's - two in comments, and the incorrect clock was
specified for the LCD device.
Signed-off-by: Andrew Victor <andrew@sanpeople.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Ben Dooks