Since commit 461972d8a4 (musb_core: don't call
musb_platform_exit() twice), unloading the driver module results in a WARNING
"kobject: '(null)' (c73de788): is not initialized, yet kobject_put() is being
called." (or even kernel oops) on e.g. DaVincis, though only in the OTG mode.
There exists dubious and unbalanced put_device() call in musb_free() which
takes place only in the OTG mode. As this commit caused musb_platform_exit()
to be called (and so unregister the NOP transceiver) before this put_device()
call, this function references already freed memory.
On the other hand, all the glue layers miss the otg_put_transceiver() call,
complementary to the otg_get_transceiver() call that they do. So, I think
the solution is to get rid of the strange put_device() call, and instead
call otg_put_transceiver() in the glue layers...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Extends FSL EHCI platform driver glue layer to support
MPC5121 USB controllers. MPC5121 Rev 2.0 silicon EHCI
registers are in big endian format. The appropriate flags
are set using the information in the platform data structure.
MPC83xx system interface registers are not available on
MPC512x, so the access to these registers is isolated in
MPC512x case. Furthermore the USB controller clocks
must be enabled before 512x register accesses which is
done by providing platform specific init callback.
The MPC512x internal USB PHY doesn't provide supply voltage.
For boards using different power switches allow specifying
DRVVBUS and PWR_FAULT signal polarity of the MPC5121 internal
PHY using "fsl,invert-drvvbus" and "fsl,invert-pwr-fault"
properties in the device tree USB nodes. Adds documentation
for this new device tree bindings.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Replace FSL USB platform code by simple platform driver for
creation of FSL USB platform devices.
The driver creates platform devices based on the information
from USB nodes in the flat device tree. This is the replacement
for old arch fsl_soc usb code removed by this patch. The driver
uses usual of-style binding, available EHCI-HCD and UDC
drivers can be bound to the created devices. The new of-style
driver additionaly instantiates USB OTG platform device, as the
appropriate USB OTG driver will be added soon.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Kumar Gala <galak@kernel.crashing.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The OpenDCC project is developing a new hardware. This patch adds its
PID to the list of known FTDI devices. The PID can be found at
http://www.opendcc.de/elektronik/usb/opendcc_usb.html
Signed-off-by: Rainer Keller <mail@rainerkeller.de>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
commit 633ba7876b96ec339ef685357e2f7c60b5a8ce85 broke
g_file_storage functionality by enabling AUTOCLEAR on
all cases without caring for all gadget drivers.
This patch will only enable AUTOCLEAR if our endpoint's
FIFO was configured with double buffering support. Note
this is not a complete fix, double buffered case still
doesn't work always, but that hasn't been working for
quite some time. Other than reverting the entire commit
and breaking testusb with double buffered case again,
I decided it was better to fix the single buffered case
and spend more time fixing double buffered case properly.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the problem reported by Sergei:
>how come? we need to send ZLP before giving back the request.
>Well, look at the code ionce again. We need to send ZLP *after*
>request->actual == request->length, but as the check is inserted
>after the ZLP send, ZLP *may* be sent once the first DMA completes,
>not the last.
The patch also has been discussed on the link below:
http://marc.info/?t=128454814900001&r=1&w=2
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reported-by: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This will ignore any SESSREQ interrupt if musb is B state.
Charger detection may cause spurious SESSREQ interrupts.
Signed-off-by: Heikki Krogerus <ext-heikki.krogerus@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
musb_g_rx() always returns if next_request() call yields NULL, so the DBG()
near the function's end can never be invoked. Remove it along with unneeded
'return'; also remove the duplicate 'request' check...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Wrap flags with uninitialized_var() to suppress this:
drivers/usb/musb/cppi_dma.c:1158: warning: 'flags' may be used uninitialized
in this function
Signed-off-by: Jon Povey <jon.povey@racelogic.co.uk>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for MUSB Host DMA transfers greater than max
channel length, so that such transfers won't be truncated.
Signed-off-by: Anil Shetty <anil@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Since not all platforms are using the same offset 0x10 in
musb_save/restore_context() eg Blackfin the offset is 0x40,
Change the indexed address to direct.
Signed-off-by: Bob Liu <lliubbo@gmail.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The USB stack maps the buffer for DMA if the controller supports DMA.
MUSB controller can perform DMA as well as PIO transfers.
The buffer needs to be unmapped before CPU can perform
PIO data transfers.
Export unmap_urb_for_dma() so that drivers can perform
the DMA unmapping in a sane way.
Signed-off-by: Maulik Mankad <x0082077@ti.com>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
MUSB's DMA controller max channel length was set to 64k.
Transfer length greater than this max value is being truncated.
Signed-off-by: Anil Shetty <anil@ti.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch has been tested OK on beagle B5 board and
use usbtest #15 and #16 as testcase.
Signed-off-by: Ming Lei <tom.leiming@gmail.com>
Reviewed-by: Sergei Shtylyov <sshtylyov@mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Anand Gadiyar <gadiyar@ti.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Enabling CONFIG_USB_MUSB_DEBUG option causes -DDEBUG to be added to gcc's
command line, however the DBG() macro doesn't depend on DEBUG, so that the
debugging messages get printed regardless of the option, and I don't think
that this was intended. Get rid of otherwise unused xprintk() macro and make
DBG() macro directly call pr_debug() which only results in the actual code
generated if DEBUG is defined.
This change makes musb_hdrc.o ~30% less in size with CONFIG_USB_MUSB_DEBUG
disabled (in host mode).
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes the memory leak on disconnecting the device.
In addition, it fixes some messages corrupted by incorrect encoding.
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This assigns the minor number 192 to the yurex driver.
We also fix up the previous usb minor number entry, it was wrong.
Cc: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Meywa-Denki/Kayac YUREX is a leg-shakes sensor device.
See http://bbu.kayac.com/en/about/ for further information.
This driver support read/write the leg-shakes counter in the device
via a device file /dev/yurex[0-9]*.
[minor coding style cleanups fixed by gregkh]
Signed-off-by: Tomoki Sekiyama <tomoki.sekiyama@gmail.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit changes storage_common.c and file_storage.c to
reuse definitions from linux/usb/storage.h header file.
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
USB Attached SCSI is a new protocol specified jointly by the SCSI T10
committee and the USB Implementors Forum.
Signed-off-by: Matthew Wilcox <willy@linux.intel.com>
Cc: Matthew Dharm <mdharm-usb@one-eyed-alien.net>
[mina86@mina86.com: updated to use new USB_ prefix]
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This commit changes prefix for some of the USB mass storage
class related macros (ie. USB_SC_ for subclass and USB_PR_
for class).
Signed-off-by: Michal Nazarewicz <mina86@mina86.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Matthew Wilcox <willy@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
this patch to qcserial.c enables the Diagnostics Monitor
and NMEA GPS ports on Qualcomm Gobi 2000 devices.
A Gobi 2000 device will provide 3 serial ports:
# /dev/ttyUSB0 -> Diagnostics
# /dev/ttyUSB1 -> 3G Modem
# /dev/ttyUSB2 -> NMEA GPS port
* The Diagnostics Monitor uses Qualcomm's DM protocol; I used
libqcdm (ModemManager) to talk to it, found it working, but at
least DM commands 12 and 64 are not implemented on my device
(Gobi 2000 built into Thinkpad x100e).
* Functionality of the 3G Modem port remains unchanged.
* The GPS port and how to enable it has been confirmed now in the
Gobi 3000 source code at:
https://www.codeaurora.org/patches/quic/gobi/
Enable/disable GPS via:
echo "\$GPS_START" > /dev/ttyUSB2
# use GPS
echo "\$GPS_STOP" > /dev/ttyUSB2
Signed-off-by: Matthias G. Eckermann <mge@arcor.de>
This reverts commit 6a1a82df91.
RTS and DTR should not be modified based on CRTSCTS when calling
set_termios.
Modem control lines are raised at port open by the tty layer and should stay
raised regardless of whether hardware flow control is enabled or not.
This is in conformance with the way serial ports work today and many
applications depend on this behaviour to be able to talk to hardware
implementing hardware flow control (without the applications actually using
it).
Hardware which expects different behaviour on these lines can always
use TIOCMSET/TIOCMBI[SC] after port open to change them.
Reported-by: Daniel Mack <daniel@caiaq.de>
Reported-by: Dave Mielke <dave@mielke.cc>
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch, adds to the option driver the Onda Communication
(http://www.ondacommunication.com) vendor id, and the MT825UP modem
device id.
Note that many variants of this same device are being release here in
Italy (at least one or two per telephony operator).
These devices are perfectly equivalent except for some predefined
settings (which can be changed of course).
It should be noted that most ONDA devices are allready supported (they
used other vendor's ids in the past). The patch seems working fine here,
and the rest of the driver seems uninfluenced.
Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The un-registration of OHCI driver was not done in the ohci_hcd_mod_exit
function. This was affecting rmmod command not to work for OMAP3
platforms. The platform driver un-registration for OMAP3 platforms is
perfomed while removing the OHCI module from kernel.
Signed-off-by: Keshava Munegowda <keshava_mgowda@ti.com>
Signed-of-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds support for Accesio USB to Serial adapters, which are built around
FTDI FT232 UARTs. Tested with the Accesio USB-COM-4SM.
Signed-off-by: Rich Mattes <richmattes@gmail.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The /sys/kernel/debug/usb/devices file doesn't know about Wireless or
SuperSpeed USB. This patch (as1416b) teaches it, and updates the
Documentation/usb/proc_sub_info.txt file accordingly.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Vrabel <david.vrabel@csr.com>
CC: Sarah Sharp <sarah.a.sharp@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are lots of ZTE USB id's currently not covered by usb/serial. Adds them,
to allow those devices to work properly on Linux.
While here, put the USB ID's for 0x2002/0x2003 at the sorted order.
This patch is based on zte.c file found on MF645.
PS.: The ZTE driver is commenting the USB ID for 0x0053. It also adds, commented,
an USB ID for 0x0026.
Not sure why, but I think that 0053 is used by their devices in storage mode only.
So, I opted to keep the comment on this patch.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In today linux-next I got a compile error on usb/host/isp1362-hcd:
drivers/usb/host/isp1362-hcd.c: In function ‘isp1362_hub_control’:
drivers/usb/host/isp1362-hcd.c:1680: error: ‘ohci’ undeclared (first use in this function)
The problem is when the CONFIG_USB_OTG option is enabled.
ohci variable is never declared and there isn't any CONFIG_USB_OTG dependent code
besides the portion defined in isp1362_hub_control.
So I think that maybe USB OTG support is not needed/supported.
This patch removes the CONFIG_USB_OTG dependent block so the driver can compile cleanly.
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Lothar Wassmann <LW@KARO-electronics.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The composite gadget will OOPS if the host sends a control request
targetted to an interface of an un-configured composite device. This patch
prevents this.
The OOPS was observed during WHQL USB CV tests. With this patch, the device
STALLs as per requirement.
Failing test case: From host do the following. I used libusb-1.0
1) Set configuration to zero.
libusb_control_transfer(device_handle,
0, /* standard OUT */
0x9, /* setConfiguration */
0, 0, NULL, 0, 0);
2) Query current configuratioan.
libusb_control_transfer(device_handle,
0x80, /* standard IN*/
0x8, /* getConfiguration */
0, 0, data, 1, 0);
3) Send the non-standard ctrl transfer targetted to interface
libusb_control_transfer(device_handle,
0x81, /* standard IN to interface*/
0x6, /* getDescriptor */
0x2300, 0, data, 0x12, 0);
Signed-off-by: Roger Quadros <roger.quadros@nokia.com>
Cc: stable <stable@kernel.org>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Robert Lukassen <robert.lukassen@tomtom.com>
Cc: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1417) fixes a problem affecting some (or all) nVidia
chipsets. When the computer is shut down, the OHCI controllers
continue to power the USB buses and evidently they drive a Reset
signal out all their ports. This prevents attached devices from going
to low power. Mouse LEDs stay on, for example, which is disconcerting
for users and a drain on laptop batteries.
The fix involves leaving each OHCI controller in the OPERATIONAL state
during system shutdown rather than putting it in the RESET state.
Although this nominally means the controller is running, in fact it's
not doing very much since all the schedules are all disabled. However
there is ongoing DMA to the Host Controller Communications Area, so
the patch also disables the bus-master capability of all PCI USB
controllers after the shutdown routine runs.
The fix is applied only to nVidia-based PCI OHCI controllers, so it
shouldn't cause problems on systems using other hardware. As an added
safety measure, in case the kernel encounters one of these running
controllers during boot, the patch changes quirk_usb_handoff_ohci()
(which runs early on during PCI discovery) to reset the controller
before anything bad can happen.
Reported-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
CC: David Brownell <david-b@pacbell.net>
Tested-by: Pali Rohár <pali.rohar@gmail.com>
CC: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The protocol code is set 00 in IAD and it's set to 01 in ACM control
interface descriptor in f_acm.c file. Due to this, windows is unable to
install the modem(ACM) driver based on class-subclass-protocol matching.
This patch corrects the protocol code in ACM IAD to the same as in
acm_control_interface_desc protocol code.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Praveena Nadahally <praveen.nadahally@stericsson.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In today linux-next I got a compile warning due a possible uninitialized variable
This patch solves the issue initializing the variable
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Magnus Damm <damm@opensource.se>
Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch updated Kconfig for langwell otg transceiver driver.
Add ipc driver(INTEL_SCU_IPC) as a dependency. Driver version is
updated too.
Signed-off-by: Hao Wu <hao.wu@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The "mutex" ftdi->sw_lock is used as a lock and a completion. Convert
it to a real semaphore which allows both.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
tdi_reset is already taking care of setting host mode for tdi devices.
Don't duplicate code in platform driver.
Make ehci_halt a nop if the controller is not in host mode (otherwise it
will fail), and let's ehci_reset do the tdi_reset.
We need to move hcd->has_tt flags before ehci_halt, in order ehci_halt
knows we are a tdi device.
Before the setup routine was doing :
- put controller in host mode
- ehci_halt
- ehci_init
- hcd->has_tt = 1;
- ehci_reset
Now we do :
- hcd->has_tt = 1;
- ehci_halt
- ehci_init
- ehci_reset
PS : now we handle correctly the device -> host transition.
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
It's spelled "Function Filesystem" / "FunctionFS". This patch
fixes some typos (FunctioFS->FunctionFS, Funcion->Function,
funcion->function, redundant "as") in the Kconfig description of
USB_FUNCTIONFS*.
Signed-off-by: Michael Prokop <mika@grml.org>
Acked-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch (as1413) changes g_file_storage to avoid generating a bogus
automatic serial-number string descriptor. If the user doesn't provide
a valid serial number via a module parameter then a warning is logged
and the gadget won't have any serial string descriptor at all.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: David Brownell <david-b@pacbell.net>
CC: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There are about 2500 void functions in drivers/usb
Only a few used return; at end of function.
Standardize them a bit.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Cc: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Commit f661c6f8c6 adds a check of the pipe type if
CONFIG_USB_DEBUG is enabled, but it doesn't output anything if this scenario
occurs.
Signed-off-by: Simon Arlott <simon@fire.lp0.eu>
Cc: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The same expression is tested twice and the result is the same each time.
Instead test for use_dma_ppb as in the test above.
The sematic match that finds this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@expression@
expression E;
@@
(
* E
|| ... || E
|
* E
&& ... && E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bind function is most of the time only called at init time so there
is no need to save a pointer to it in the configuration structure.
This fixes many section mismatches reported by modpost.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[m.nazarewicz@samsung.com: updated for -next]
Signed-off-by: Michał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The bind function is most of the time only called at init time so there
is no need to save a pointer to it in the composite driver structure.
This fixes many section mismatches reported by modpost.
Signed-off-by: Michał Nazarewicz <m.nazarewicz@samsung.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
To accomplish this the function to register a gadget driver takes the bind
function as a second argument. To make things clearer rename the function
to resemble platform_driver_probe.
This fixes many section mismatches like
WARNING: drivers/usb/gadget/g_printer.o(.data+0xc): Section mismatch in
reference from the variable printer_driver to the function
.init.text:printer_bind()
The variable printer_driver references
the function __init printer_bind()
All callers are fixed.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
[m.nazarewicz@samsung.com: added dbgp]
Signed-off-by: Michał Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts a commit which proposed an invalid solution
for a section mismatch. Next 3 commits will fix it correctly.
Conflicts:
drivers/usb/gadget/mass_storage.c
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes some of the string registration from the
Multifunction Composite Gadget as composite layer can handle
the iManufacturer and iProduct for us.
This also adds the "needs_serial" so that composite layer will
issue a warning if user space fails to provide the iSerialNumber
module parameter.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes string registration from the Mass Storage
Gadget. With recent changes to the composite framework, all
that we need is handled by the composite layer. This means
composite registers a string ID for manufacturer and product.
This also adds the "needs_serial" so that composite layer will
issue a warning if user space fails to provide the iSerialNumber
module parameter.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The iManufatcurer, iProduct and iSerialNumber composite module
parameters were only used when the gadget driver registers
strings for manufacturer, product and serial number. If the
gadget never bothered to set corresponding fields in USB device
descriptors those module parameters are ignored.
This commit makes the parameters work even if the strings ID
have not been assigned. It also changes the way IDs are
overridden -- what IDs are overridden is now saved in
usb_composite_dev structure -- which makes it unnecessary to
modify the string tables the way previous code did.
The commit also adds a iProduct and iManufatcurer fields to the
usb_composite_device structure. If they are set, appropriate
strings are reserved and added to device descriptor. This makes
it unnecessary for gadget drivers to maintain code for setting
those. If iProduct is not set it defaults to
usb_composite_device::name; if iManufatcurer is not set
a default "<system> <release> with <gadget-name>" is used.
The last thing is that if needs_serial field of
usb_composite_device is set and user failed to provided
iSerialNumber parameter a warning is issued.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes some of the string registration from the
FunctionFS Gadget as composite layer can handle the
iManufacturer and iProduct for us.
It also removes some of the module parameters which were
redundant as well as changes the name of others to better much
the module parameter of the composite layer.
Other then that, it also fixes formatting of multiline comments
to match the coding style.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The nofua parameter (optionally ignore SCSI WRITE FUA) was added
to the File Storage Gadget some time ago. This patch adds the
same functionality to the Mass Storage Function.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Cc: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The dev_attr_nofua file was created during fsg_bind() but
was never removed. Made it a bit more symmetrical and added
code to remove the file in fsg_unbind().
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Acked-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the vendor and product ID the gadget uses
by replacing the temporary IDs that were used during
development (which should never get into mainline) with
proper IDs.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes the vendor and product ID the gadget uses
by replacing the temporary IDs that were used during
development (which should never get into mainline) with
proper IDs.
Signed-off-by: Michal Nazarewicz <m.nazarewicz@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Found while debugging a USB problem and trying to find the mentioned function.
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add new driver to access the SAM-BA boot application of Atmel AT91SAM
devices.
The SAM-BA firmware cannot handle merged write requests so we cannot use
the generic write implementation (which uses the port write fifo).
Tested with the SAM-BA 2.10 tools and an Atmel at91sam9260-ek.
Signed-off-by: Johan Hovold <jhovold@gmail.com>
Tested-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
len is always greater than or equal to zero here. First of all, it's
type is unsigned and also we only assign it numbers which are greater
than or equal to zero.
Removing the check lets us pull everything in an indent level.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Stephane duverger <stephane.duverger@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
SRAM Memory handling for USB client function
Signed-off-by: JiebingLi <jiebing.li@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Remote wakeup support in client driver. Made non-debug only this time.
Signed-off-by: JiebingLi <jiebing.li@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
PHY low power mode setting with a static function
Signed-off-by: JiebingLi <jiebing.li@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Code cleanup by using standard debugging API's and USB inline functions
Signed-off-by: JiebingLi <jiebing.li@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds support for the USB transceiver driver in the Langwell chipset used
on the Intel MID platforms. It folds up the original patch set which includes
basic support for the device, PHY low power mode (Please notice that there is
a limitation, after we drive VBus down, 2ms delay is required from SCU FW to
sync up OTGSC register with USBCFG register), software timers (the hardware
timers do not work in low power mode), HNP, SRP.
Signed-off-by: Hao Wu <hao.wu@intel.com>
Signed-off-by: Alek Du <alek.du@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Running a serial console, if too many kernel messages are generated within
a short time causing a lot of serial I/O, the 8250 driver will generate
another kernel message reporting this, which just adds to the I/O. It has
a cascading effect and quickly results the system being brought to its knees
by a flood of "too much work" messages.
Ratelimit the error message to avoid this.
[akpm@linux-foundation.org: use the superior printk_ratelimited()]
[akpm@linux-foundation.org: printk_ratelimited() needs ratelimit.h]
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The actual uart baud rate of devices vary between +/-2% of what is
asked. The SPORT RX sample rate should be faster than double of the
worst case. Otherwise, wrong data may be received. So set SPORT RX
clock to be 3% faster in general.
Reported-by: Olivier STOCK <ostockemer@ereca.fr>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Not every platform that has generic legacy 8250 ports manages to have them
clocked the right way or without errata. Provide a generic interface to
allow platforms to override the default behaviour in a manner that dumps
the complexity in *their* code not the 8250 driver.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Dirk Brandewie <dirk.brandewie@gmail.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The .start_tx callback (imx_start_tx here) isn't only called when the
buffer is non-empty. E.g. after resume or when handshaking is enabled
and the other side starts to signal being ready.
So check for an empty puffer already before sending the first character.
This prevents sending out stale (or uninitialised) data.
Signed-off-by: Volker Ernst <volker.ernst@txtr.com>
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Cc: Andy Green <andy@warmcat.com>
[ukl: reword commit log, put check in while condition]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add more baud rates support referring the baud_table[] defined
in drivers/char/tty_ioctl.c: 3000000/2000000/1000000/500000
Signed-off-by: Feng Tang <feng.tang@intel.com>
Acked-by: Alan Cox <alan.cox@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
If kzmalloc fails, the uart port is not removed causing a leak.
This patch just add another label that removes the uart when the
kzmalloc fails.
Signed-off-by: Breno Leitao <leitao@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a hook for platforms to specify custom pm methods.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
port->flags is of type upf_t, which corresponds to UPF_* flags.
ASYNC_BOOT_AUTOCONF is an unsigned integer, which happen to
be the same as UPF_BOOT_AUTOCONF.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This fixes tty name, major and minor numbers. The major number
204 is used across many platform-specific serial drivers, so we
use that.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some controllers implement registers with a stride, to support
those we must implement the proper IO accessors.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes it much easier to integrate the driver with the rest of
the Linux (e.g. MFD subsystem).
The old method is still supported though.
Also, from now on, there is one platform device per port (no
changes are needed for the platform code, as no one registers
the devices anywhere in-tree yet).
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Alan Cox <alan@linux.intel.com>,
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some Altera UART implementations doesn't route the IRQ line, so we have
to work in polling mode.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Acked-by: Tobias Klauser <tklauser@distanz.ch>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Soon we will use that handy function in the altera_uart driver.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The loop in wait_for_xmitr() is delaying one extra uS after the ready
condition has been met. Rewrite the loop to only delay if the
transmitter is not ready.
Signed-off-by: David Daney <ddaney@caviumnetworks.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
A notifier chain is called whenever the vt code modifies a terminal
content, except for one case which is when the modification comes
through writes to /dev/vcs* devices. Let's add the missing notifier
invocation at the end of vcs_write() for that case too.
Signed-off-by: Nicolas Pitre <nicolas.pitre@canonical.com>
Cc: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The /dev/vcs* devices are used, amongst other things, by accessibility
applications such as BRLTTY to display the screen content onto refreshable
braille displays. Currently this is performed by constantly reading from
/dev/vcsa0 whether or not the screen content has changed. Given the
default braille refresh rate of 25 times per second, this easily qualifies
as the biggest source of wake-up events preventing laptops from entering
deeper power saving states.
To avoid this periodic polling, let's add support for select()/poll() and
SIGIO with the /dev/vcs* devices. The implemented semantic is to report
data availability whenever the corresponding vt has seen some update after
the last read() operation. The application still has to lseek() back
as usual in order to read() the new data.
Not to create unwanted overhead, the needed data structure is allocated
and the vt notification callback is registered only when the poll or
fasync method is invoked for the first time per file instance.
Signed-off-by: Nicolas Pitre <nicolas.pitre@canonical.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Again basically cut and paste
Convert the main driver set to use the hooks for GICOUNT
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Simple pasting job using the new ops function. Also fix a couple of devices
directly returning the internal struct (which happens at this point to match
for the fields that matter but isn't correct or futureproof)
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Dan Rosenberg noted that various drivers return the struct with uncleared
fields. Instead of spending forever trying to stomp all the drivers that
get it wrong (and every new driver) do the job in one place.
This first patch adds the needed operations and hooks them up, including
the needed USB midlayer and serial core plumbing.
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
And while we are at it allow it to fail to find one. Without this the IRQ
option will cause the 3110 driver to fail on 0.7 SFI firmware.
Acked-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The cleanup for mrst_max3110 includes:
* remove unneeded head files
* make the spi_transfer dma safe, so that driver is more portable
* add more check for error return value
* use mutex_trylock for read thread
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Function tty_register_device may return ERR_PTR(...). Check for it.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Vasiliy found that pci_disable_device is not called on fail paths in
mxser_probe. Actually, it is called from nowhere in the driver.
There are three changes needed:
1) don't use pseudo-generic mxser_release_res. Let's use it only from
ISA paths from now on. All the pci stuff is moved to probe and
remove PCI-related functions.
2) reorder fail-paths in the probe function so that it makes sense and
we can call them from the sequential code naturally (the further we
are the earlier label we go to).
3) add pci_disable_device both to mxser_probe and mxser_remove.
There is a nit of adding CONFIG_PCI ifdef to mxser_remove. it is
because this driver supports ISA-only compilations and it would choke
up on the newly added calls now.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Kulikov Vasiliy <segooon@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Ttyprintk is a pseudo TTY driver, which allows users to make printk
messages, via output to ttyprintk device. It is possible to store
"console" messages inline with kernel messages for better analyses of
the boot process, for example.
Signed-off-by: Samo Pogacnik <samo_pogacnik@t-2.net>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The commit 4547be7 rewrites suspend and resume functions. According
to this rewrite, when a serial port is a printk console device and
can suspend(without set no_console_suspend flag), it will definitely
call set_termios function during its resume, but parameter termios
isn't initialized, this will pass an unpredictable config to the
serial port. If this serial port is not a userspace opened tty device
, a suspend and resume action will make this serial port unusable.
I.E. ttyS0 is a printk console device, ttyS1 or keyboard+display is
userspace tty device, a suspend/resume action will make ttyS0
unusable.
If a serial port is both a printk console device and an opened tty
device, this issue can be overcome because it will call set_termios
again with the correct parameter in the uart_change_speed function.
Refer to the deleted content of commit 4547be7, revert parts relate
to restore settings into parameter termios. It is safe because if
a serial port is a printk console only device, the only meaningful
field in termios is c_cflag and its old config is saved in
uport->cons->cflag, if this port is also an opened tty device,
it will clear uport->cons->cflag in the uart_open and the old config
is saved in tty->termios.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Stanislav Brabec <sbrabec@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The commit 4547be7 rewrites suspend and resume functions, this
introduces a problem on the OMAP3EVM platoform. when the kernel boots
with no_console_suspend and we suspend the kernel, then resume it,
the serial console will be not usable. This problem should be common
for all platforms.
The cause for this problem is that when enter suspend, if we choose
no_console_suspend, the console_stop will be skiped. But in resume
function, the console port will be set to uninitialized state by
calling set_termios function and the console_start is called without
checking whether the no_console_suspend is set, Now fix it.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Acked-by: Stanislav Brabec <sbrabec@suse.cz>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes __GFP_NOFAIL use from tty_add_file() and adds proper error
handling to the call-sites of the function.
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Pekka Enberg <penberg@kernel.org>
Acked-by: David Rientjes <rientjes@google.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
CONSOLE_POLL support for uartlite enables
KGDB debugging over serial line.
Signed-off-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
Acked-by: Peter Korsgaard <jacmet@sunsite.dk>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
snprintf() returns the number of bytes which would have been written so
it can be larger than the size of the buffer. In this case it's fine,
but people copy and paste this code so I've fixed it.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Make serport serio device to be a child of corresponding tty device
instead of just hanging at /sys/devices/serioX.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some device drivers (mostly tty line disciplines) would like to have way
know a struct device instance corresponding to passed tty_struct. Add
a struct device pointer to struct tty_struct and populate it during
initialize_tty_struct().
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Aid diagnostics by printing the error code from failed suspends, which
doesn't otherwise seem to get displayed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a section count property to the memory_block struct to track the number
of memory sections that have been added/removed from a memory block. This
allows us to know when the last memory section of a memory block has been
removed so we can remove the memory block.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Reviewed-by: Robin Holt <holt@sgi.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add a new mutex for use in adding and removing of memory blocks. This
is needed to avoid any race conditions in which the same memory block could
be added and removed at the same time.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Reviewed-by: Robin Holt <holt@sgi.com>
Reviewed-By: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Move the find_memory_block() routine up to avoid needing a forward
declaration in subsequent patches.
Signed-off-by: Nathan Fontenot <nfont@austin.ibm.com>
Reviewed-by: Robin Holt <holt@sgi.com>
Reviewed-By: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This driver supports iLO, iLO2 and iLO3. However, comments and Kconfig
reference only iLO and iLO2. Let's just call it "iLO" to avoid having to
update strings for each iLO generation. This is similar to the change made
to hpwdt in commit 36e3ff44ce.
Signed-off-by: dann frazier <dannf@hp.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Modify link_mem_sections() to pass in the previous mem_block as a hint to
locating the next mem_block. Since they are typically added in order this
results in a massive saving in time during boot of a very large system.
For example, on a 16TB x86_64 machine, it reduced the total time spent
linking all node's memory sections from 1 hour, 27 minutes to 46 seconds.
Signed-off-by: Robin Holt <holt@sgi.com>
To: Gary Hade <garyhade@us.ibm.com>
To: Badari Pulavarty <pbadari@us.ibm.com>
To: Ingo Molnar <mingo@elte.hu>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Introduce a find_memory_block_hinted() which utilizes the
recently added kset_find_obj_hinted().
Signed-off-by: Robin Holt <holt@sgi.com>
To: Dave Hansen <haveblue@us.ibm.com>
To: Matt Tolentino <matthew.e.tolentino@intel.com>
Reviewed-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix build errors when CONFIG_BLOCK is not enabled:
drivers/base/core.c: In function 'get_device_parent':
drivers/base/core.c:634: error: 'block_class' undeclared (first use in this function)
drivers/base/core.c: In function 'device_add_class_symlinks':
drivers/base/core.c:723: error: 'block_class' undeclared (first use in this function)
drivers/base/core.c: In function 'device_remove_class_symlinks':
drivers/base/core.c:751: error: 'block_class' undeclared (first use in this function)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix kconfig dependency warning for FW_LOADER.
Lots of drivers select FW_LOADER without bothering to depend on
HOTPLUG and/or without selecting HOTPLUG. A kernel builds fine
when FW_LOADER is enabled, whether HOTPLUG is enabled or not, and
a kernel config file (make oldconfig) is not changed by this patch.
(Yes, drivers/base/firmware_class.c uses interfaces from linux/kobject.h,
which does have some CONFIG_HOTPLUG dependencies, but this patch does
not change that.)
warning: (MICROCODE || MICROCODE_INTEL && MICROCODE || MICROCODE_AMD && MICROCODE || PCMCIA_LOAD_CIS && PCCARD && PCMCIA && EXPERIMENTAL || USB_IRDA && NET && IRDA && USB || BT_HCIBCM203X && NET && BT && USB || BT_HCIBFUSB && NET && BT && USB || BT_HCIBT3C && NET && BT && PCMCIA || BT_MRVL_SDIO && NET
...
!STAGING_EXCLUDE_BUILD && USB && (X86 || ARM) && WLAN || DRM_NOUVEAU && STAGING && !STAGING_EXCLUDE_BUILD && DRM && PCI || TI_ST && STAGING && !STAGING_EXCLUDE_BUILD && RFKILL || DELL_RBU && X86) selects FW_LOADER which has unmet direct dependencies (HOTPLUG)
(5200 byte line reduced a lot)
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Instead of adding uio class attributes manually after the uio device has
been created and we have sent a uevent to userspace, use the class
attribute mechanism. This removes races and makes the code simpler.
At the same time don't bother to dynamically allocate a struct class for
uio, just declare one statically. Less code is needed and it is easier
to set the class parameters.tune the class
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
register_chrdev limits uio devices to 256 minor numbers which causes
problems on one system I have with 384+ uio devices. So instead set
UIO_MAX_DEVICES to the maximum number of minors and use
alloc_chrdev_region to reserve the uio minors.
The final result is that the code works the same but the uio driver now
supports any minor the idr allocator comes up with.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Change the value of UIO_IRQ_NONE -2 to 0. 0 is well defined in the rest
of the kernel as the value to indicate an irq has not been assigned.
Update the calls to request_irq and free_irq to only ignore UIO_IRQ_NONE
and UIO_IRQ_CUSTOM allowing the rest of the kernel's possible irq
numbers to be used.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently uio sets it's driver data to NULL just as it is unregistering
attributes. sysfs maks the guaranatee that it will not call attributes
after device_destroy is called so this is unncessary and leads to lots
of unnecessary code in uio.c
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There is no locking in init_uio_class so multiple
drivers can race and create multiple uio classes.
Fix this by simplifying the code. In particular always
register the uio class during module_init and make things
simpler.
Signed-off-by: Eric W. Biederman <ebiederm@aristanetworks.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
I have some systems which need legacy sysfs due to old tools that are
making assumptions that a directory can never be a symlink to another
directory, and it's a big hazzle to compile separate kernels for them.
This patch turns CONFIG_SYSFS_DEPRECATED into a run time option
that can be switched on/off the kernel command line. This way
the same binary can be used in both cases with just a option
on the command line.
The old CONFIG_SYSFS_DEPRECATED_V2 option is still there to set
the default. I kept the weird name to not break existing
config files.
Also the compat code can be still completely disabled by undefining
CONFIG_SYSFS_DEPRECATED_SWITCH -- just the optimizer takes
care of this now instead of lots of ifdefs. This makes the code
look nicer.
v2: This is an updated version on top of Kay's patch to only
handle the block devices. I tested it on my old systems
and that seems to work.
Cc: axboe@kernel.dk
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch removes the old CONFIG_SYSFS_DEPRECATED_V2 config option,
but it keeps the logic around to handle block devices in the old manner
as some people like to run new kernel versions on old (pre 2007/2008)
distros.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Stephen Hemminger <shemminger@vyatta.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: "James E.J. Bottomley" <James.Bottomley@suse.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
Cc: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jaroslav Kysela <perex@perex.cz>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: David Howells <dhowells@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
There's no need to explicitly check for data and resources being NULL,
as platform_device_add_{data,resources}() do this internally nowadays.
This makes the code more linear and less indented.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Some users of platform_device_add_{data,resources}() assume that
NULL data and resources will be handled specially, i.e. just ignored.
But the platform core ends up calling kmemdup(NULL, 0, ...), which
returns a non-NULL result (i.e. ZERO_SIZE_PTR), which causes drivers
to oops on a valid code, something like:
if (platform_data)
stuff = platform_data->stuff;
This patch makes the platform core a bit more safe for such cases.
Signed-off-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This patch fixes up all of the build warnings for the pch_phub driver.
Cc: Masayuki Ohtake <masa-korg@dsn.okisemi.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Packet hub driver of Topcliff PCH
Topcliff PCH is the platform controller hub that is going to be used in
Intel's upcoming general embedded platform. All IO peripherals in
Topcliff PCH are actually devices sitting on AMBA bus. Packet hub is
a special converter device in Topcliff PCH that translate AMBA transactions
to PCI Express transactions and vice versa. Thus packet hub helps present
all IO peripherals in Topcliff PCH as PCIE devices to IA system.
Topcliff PCH has MAC address and Option ROM data.
These data are in SROM which is connected to PCIE bus.
Packet hub driver of Topcliff PCH can access MAC address and Option ROM data in
SROM via sysfs interface.
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Currently, the platform_bus allows customization of several of the
busses dev_pm_ops methods by using weak symbols so that platform code
can override them. The weak-symbol approach is not scalable when
wanting to support multiple platforms in a single kernel binary.
Instead, provide __init methods for platform code to customize the
dev_pm_ops methods at runtime.
NOTE: after these dynamic methods are merged, the weak symbols should
be removed from drivers/base/platform.c. AFAIK, this will only
affect SH and sh-mobile which should be converted to use this
runtime approach instead of the weak symbols. After SH &
sh-mobile are converted, the weak symobols could be removed.
Tested on OMAP3.
Cc: Magnus Damm <magnus.damm@gmail.com>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
IRQ and resource[] may not have correct values until
after PCI hotplug setup occurs at pci_enable_device() time.
The semantic match that finds this problem is as follows:
// <smpl>
@@
identifier x;
identifier request ~= "pci_request.*|pci_resource.*";
@@
(
* x->irq
|
* x->resource
|
* request(x, ...)
)
...
*pci_enable_device(x)
// </smpl>
Signed-off-by: Kulikov Vasiliy <segooon@gmail.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: Hans J. Koch <hjk@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
In theory (although not *yet* in practice), a driver being passed
to platform_driver_probe might have driver.bus set to something
other than platform_bus_type. Locking drv->driver.bus is always
correct.
Signed-off-by: Patrick Pannuto <ppannuto@codeaurora.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fortunately this is only exploitable on very unusual hardware.
[Reported a while ago but nothing happened so just fixing it]
Signed-off-by: Alan Cox <alan@linux.intel.com>
Cc: stable@kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The ATAFB_FALCON ifdef isn't necessary at this point, because it is
checked in an outer ifdef level already and has no effect here.
Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Acked-by: Krzysztof Helt <krzysztof.h1@wp.pl>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
If device_register() fails then call put_device().
See comment to device_register.
Signed-off-by: Vasiliy Kulikov <segooon@gmail.com>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
This patch moves the q40_fix and q40_var structures from .init.data
to .devinit.data.
This is where now the probe function resides, which only uses them.
Signed-off-by: Henrik Kretzschmar <henne@nachtwindheim.de>
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Dave Hinds pointed out to me that 37979e1546 will break b43 and
ray_cs, as IOCARD is not -- as the name would suggest -- only needed
for cards using IO ports. Instead, as it re-deines several pins, it
is also required for using interrupts.
Signed-off-by: Dominik Brodowski <linux@dominikbrodowski.net>
* 'next' of git://git.kernel.org/pub/scm/linux/kernel/git/benh/powerpc: (71 commits)
powerpc/44x: Update ppc44x_defconfig
powerpc/watchdog: Make default timeout for Book-E watchdog a Kconfig option
fsl_rio: Add comments for sRIO registers.
powerpc/fsl-booke: Add e55xx (64-bit) smp defconfig
powerpc/fsl-booke: Add p5020 DS board support
powerpc/fsl-booke64: Use TLB CAMs to cover linear mapping on FSL 64-bit chips
powerpc/fsl-booke: Add support for FSL Arch v1.0 MMU in setup_page_sizes
powerpc/fsl-booke: Add support for FSL 64-bit e5500 core
powerpc/85xx: add cache-sram support
powerpc/85xx: add ngPIXIS FPGA device tree node to the P1022DS board
powerpc: Fix compile error with paca code on ppc64e
powerpc/fsl-booke: Add p3041 DS board support
oprofile/fsl emb: Don't set MSR[PMM] until after clearing the interrupt.
powerpc/fsl-booke: Add PCI device ids for P2040/P3041/P5010/P5020 QoirQ chips
powerpc/mpc8xxx_gpio: Add support for 'qoriq-gpio' controllers
powerpc/fsl_booke: Add support to boot from core other than 0
powerpc/p1022: Add probing for individual DMA channels
powerpc/fsl_soc: Search all global-utilities nodes for rstccr
powerpc: Fix invalid page flags in create TLB CAM path for PTE_64BIT
powerpc/mpc83xx: Support for MPC8308 P1M board
...
Fix up conflict with the generic irq_work changes in arch/powerpc/kernel/time.c
Some cards don't support changing vlan offloading settings. Make
Ethtool set_flags return -EINVAL in those cases.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'upstream-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jgarzik/libata-dev: (26 commits)
include/linux/libata.h: fix typo
pata_bf54x: fix return type of bfin_set_devctl
Drivers: ata: Makefile: replace the use of <module>-objs with <module>-y
libahci: fix result_tf handling after an ATA PIO data-in command
pata_sl82c105: implement sff_irq_check() method
pata_sil680: implement sff_irq_check() method
pata_pdc202xx_old: implement sff_irq_check() method
pata_cmd640: implement sff_irq_check() method
ata_piix: Add device ID for ICH4-L
pata_sil680: make sil680_sff_exec_command() 'static'
ata: Intel IDE-R support
libata: reorder ata_queued_cmd to remove alignment padding on 64 bit builds
libata: Signal that our SATL supports WRITE SAME(16) with UNMAP
ata_piix: remove SIDPR locking
libata: implement cross-port EH exclusion
libata: add @ap to ata_wait_register() and introduce ata_msleep()
ata_piix: implement LPM support
libata: implement LPM support for port multipliers
libata: reimplement link power management
libata: implement sata_link_scr_lpm() and make ata_dev_set_feature() global
...
* 'core-memblock-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (74 commits)
x86-64: Only set max_pfn_mapped to 512 MiB if we enter via head_64.S
xen: Cope with unmapped pages when initializing kernel pagetable
memblock, bootmem: Round pfn properly for memory and reserved regions
memblock: Annotate memblock functions with __init_memblock
memblock: Allow memblock_init to be called early
memblock/arm: Fix memblock_region_is_memory() typo
x86, memblock: Remove __memblock_x86_find_in_range_size()
memblock: Fix wraparound in find_region()
x86-32, memblock: Make add_highpages honor early reserved ranges
x86, memblock: Fix crashkernel allocation
arm, memblock: Fix the sparsemem build
memblock: Fix section mismatch warnings
powerpc, memblock: Fix memblock API change fallout
memblock, microblaze: Fix memblock API change fallout
x86: Remove old bootmem code
x86, memblock: Use memblock_memory_size()/memblock_free_memory_size() to get correct dma_reserve
x86: Remove not used early_res code
x86, memblock: Replace e820_/_early string with memblock_
x86: Use memblock to replace early_res
x86, memblock: Use memblock_debug to control debug message print out
...
Fix up trivial conflicts in arch/x86/kernel/setup.c and kernel/Makefile
The new devctl func added for us to the driver has the wrong return
type. Which is to say there shouldn't be any. This fixes compile
time warnings as there shouldn't be any runtime difference.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
ATA devices don't send D2H Reg FIS after an successful ATA PIO data-in
command. The host is supposed to take the TF and E_Status of the
preceding PIO Setup FIS. Update ahci_qc_fill_rtf() such that it takes
TF + E_Status from PIO Setup FIS after a successful ATA PIO data-in
command.
Without this patch, result_tf for such a command is filled with the
content of the previous D2H Reg FIS which belongs to a previous
command, which can make the command incorrectly seen as failed.
* Patch updated to grab the whole TF + E_Status from PIO Setup FIS
instead of just E_Status as suggested by Robert Hancock.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Mark Lord <kernel@teksavvy.com>
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Jeff Garzik <jgarzik@redhat.com>
Sergei Shtylyov