Due to some recent optimization done in the way the mac address
bytes are written into the OTP memory, some AR9485 chipsets were
forced to use the first byte from the eeprom template and the
remaining bytes are read from OTP.
AR9485 happens to use generic eeprom template which has 0x1 as
the first byte causes issues in bringing up the card.
So fixed the eeprom template accordingly to address the issue.
Cc: stable@kernel.org
Cc: Paul Stewart <pstew@google.com>
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If the driver gets a tx status report for an A-MPDU sent to a station that
just went to sleep, that leaves a race condition where this tx status can
trigger another A-MPDU transmission.
To fix this, check if the station is sleeping before queueing the tid.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ath9k_hw_4k_get_eeprom() overrides the eeprom value for txgain if the
minor version is not 19 or above with a value of 0.
ar9002_hw_init_mode_gain_regs() relies on this information to
determine whether this is a high power wifi card or not. The override
caused the driver to always use the 'normal' power tables even for
high power devices if their minor version was not high enough. Thus
leading to reduced power output.
This isn't needed for the AR9285; the check originated with the
AR9280 setup code which requires the EEPROM version check.
Signed-off-by: Marek Lindner <lindner_marek@yahoo.de>
Acked-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Adrian Chadd <adrian@freebsd.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the comments are obselete as the virtual wiphy support was removed from
the driver
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
for the ease of debugging, we display only the rate control statistics
for currently operating mode and bandwidth
Cc: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Cc: "Balasubramanian, senthilkumar" <senthilb@qca.qualcomm.com>
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Stephen reported that compilation fails if both ath6kl and ath9k are
compiled in:
drivers/net/wireless/ath/ath6kl/built-in.o: In function `htc_start':
(.opd+0x600): multiple definition of `htc_start'
drivers/net/wireless/ath/ath9k/built-in.o:(.opd+0x3e40): first defined here
drivers/net/wireless/ath/ath6kl/built-in.o: In function `.htc_stop':
(.text+0x7b40): multiple definition of `.htc_stop'
drivers/net/wireless/ath/ath9k/built-in.o:(.text+0x67b34): first defined he=
re
drivers/net/wireless/ath/ath6kl/built-in.o: In function `.htc_start':
(.text+0x7d18): multiple definition of `.htc_start'
drivers/net/wireless/ath/ath9k/built-in.o:(.text+0x67ba0): first defined he=
re
drivers/net/wireless/ath/ath6kl/built-in.o: In function `htc_stop':
(.opd+0x5e8): multiple definition of `htc_stop'
drivers/net/wireless/ath/ath9k/built-in.o:(.opd+0x3e28): first defined here
To fix this add ath6kl prefix to all public functions in htc.c.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This cleans up error handling for the beacon in case of dma mapping
failure. We need to free the skb when dma mapping fails instead of
nulling and leaking the pointer, and we should bail out to avoid
giving the hardware the bad descriptor.
Finally, we need to perform the null check after trying to update
the beacon, or else beacons will never be sent after a single
mapping failure.
Cc: stable@kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch addresses an issue with incorrect HW register
AR_PHY_TX_IQCAL_CORR_COEFF_B1 definition which leads to incorrect clibration.
Cc: stable@kernel.org
Signed-off-by: Alex Hacker <hacker@epn.ru>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The commit ebefce3d13 failed
to set proper PMU value to address ripple issue for AR9485.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
CTL power data incorrect in ctlPowerData_2G field of ar9300_eeprom.
Setting incorrect CTL power in calibration is causing lower tx power.
Tx power was reported as 3dBm while operating in channel 6 HT40+/
in channel 11 HT40- due to CTL powers in the calibration is set to
zero.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Let us enable/disable interrupts based on reference count.
By doing this we can ensure that interrupts are never be
enabled in the middle of tasklet processing. Instead of
addressing corner cases like "ath9k: avoid enabling interrupts
while processing rx", this approach handles it in generic manner.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Spur frequency was incorrectly computed with 10Mhz offset
which could cause the filter would not notch out the spur
and also this could improve rx sensitivity in HT40.
Cc: Madhan Jaganathan <madhanj@qca.qualcomm.com>
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At preset set_interrupt also enables interrupt after changing
mask. This is not necessary in all cases and also sometime it
breaks the assumption that interrupt was disabled. So let us
enable the interrupt explicity if it was disabled earlier.
This could also avoid unnecessary register ops and also helps
the follow up patch to have global ref count for interrupts ops.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The high_power tx gain table is changed to match the low_ob_db tx gain
table for both 5G and 2G.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
No need to process RxDone and ds_info status again in case
valid rx status is given.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch cleanups virtual wiphy specific frametype structure
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Nowhere the firmware memory is freed, free it during
the device destroy process.
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Sometimes, the network manager is failing to connect to the AP due
to the below kernel crash message. The reason behind this,
after issuing the connect command to the chip, the chip is sending
disconnect event and then immediately one connect event to the host
in some random cases.
The host driver resets all states (including cfg80211 state machine)
when it receives disconnect event from the chip. But, still the host
driver reports the next received connect event to cfg80211, at that time
cfg80211 SME state would have been in IDLE state, which was causing
the below kernel crash.
Now, host driver's sme state machine is checked every time before
delivering connect event to cfg80211
WARNING: at net/wireless/sme.c:517 cfg80211_connect_result+0x10d/0x120()
[..]
Call Trace:
[<c0145732>] warn_slowpath_common+0x72/0xa0
[<c05d676d>] ? cfg80211_connect_result+0x10d/0x120
[<c05d676d>] ? cfg80211_connect_result+0x10d/0x120
[<c0145782>] warn_slowpath_null+0x22/0x30
[<c05d676d>] cfg80211_connect_result+0x10d/0x120
[<f83ff497>] ath6kl_cfg80211_connect_event+0x427/0x4f0 [ath6kl]
[<c035d26a>] ? put_dec+0x2a/0xa0
[<c035d645>] ? number+0x365/0x380
[<c0154675>] ? mod_timer+0x135/0x260
[<c035e00e>] ? format_decode+0x2fe/0x370
[<c01263c8>] ? default_spin_lock_flags+0x8/0x10
[<c05fd91f>] ? _raw_spin_lock_irqsave+0x2f/0x50
[<c0146032>] ? console_unlock+0x172/0x1c0
[<f8402659>] ath6kl_connect_event+0x89/0x400 [ath6kl]
[<f840826e>] ath6kl_wmi_control_rx+0x98e/0x1d60 [ath6kl]
[<c01335b5>] ? __wake_up+0x45/0x60
[<f84053aa>] ath6kl_rx+0x56a/0x770 [ath6kl]
[<c04d0242>] ? mmc_release_host+0x22/0x40
[<c04d9329>] ? sdio_release_host+0x19/0x30
[<f840a27a>] ? ath6kl_sdio_read_write_sync+0x7a/0xc0 [ath6kl]
[<f83f82b1>] do_rx_completion+0x41/0x50 [ath6kl]
[<f83faa6a>] htc_rxmsg_pending_handler+0x6ba/0xbd0 [ath6kl]
[<f8404bb0>] ? ath6kl_tx_data_cleanup+0x30/0x30 [ath6kl]
[<f840a1c0>] ? ath6kl_sdio_irq_handler+0x30/0x70 [ath6kl]
[<f83f7cd5>] ath6kldev_intr_bh_handler+0x2a5/0x630 [ath6kl]
[<f840a1c0>] ath6kl_sdio_irq_handler+0x30/0x70 [ath6kl]
[<c04d97c7>] sdio_irq_thread+0xc7/0x2d0
[<c013aeb0>] ? default_wake_function+0x10/0x20
[<c012fc98>] ? __wake_up_common+0x48/0x70
[<c04d9700>] ? sdio_claim_irq+0x200/0x200
[<c0163854>] kthread+0x74/0x80
[<c01637e0>] ? kthread_worker_fn+0x160/0x160
[<c0604c06>] kernel_thread_helper+0x6/0x10
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use wlan_iterate_nodes() directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
By having scan_table in struct ath6kl, it makes sense to move initialization
to ath6kl_init() and deinitialization to ath6kl_destroy().
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use the bssid from ath6kl directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
This is nothing but bssid of struct ath6kl.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
And remove the reference to wmi in ath6kl_node_table.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When I connect to my Linksys WT610N AP supporting 11n I see a lot of
aggreation timeout errors:
[ 408.885053] ath6kl: aggr timeout (st 3109 end 3140)
[ 463.872108] ath6kl: aggr timeout (st 3671 end 3702)
[ 495.010060] ath6kl: aggr timeout (st 3983 end 4014)
[ 503.604047] ath6kl: aggr timeout (st 4065 end 0)
[ 518.963047] ath6kl: aggr timeout (st 141 end 172)
[ 525.014066] ath6kl: aggr timeout (st 205 end 236)
[ 573.957051] ath6kl: aggr timeout (st 701 end 732)
[ 585.019067] ath6kl: aggr timeout (st 816 end 847)
But still the connection seems to work. To not clutter the logs change
the error message to a debug message. But add a fixme comment so that
this will be investigated.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl Kconfig still had dependencies to wext, remove those as they are
not needed anymore.
Now ath6kl should not have any wext code left. Time to have a beer and
celebrate this.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
When ath6kl module was removed while a scan was ongoing the driver would
crash in ath6kl_cfg80211_scan_complete_event().
Fix the function not to iterate nodes when the scan is aborted. The nodes
are already freed when the module is being unloaded. This patch removes the
null check entirely as the wmi structure is not accessed anymore during
module unload.
Also fix a bug where the status was checked as a bitfield with '&' operator.
But it's not a bitfield, just a regular error code.
This is a port of my patch from ath6kl staging with the same title.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
ath6kl_cfg80211_scan_node() was calling cfg80211_inform_bss_frame()
with CFP_KERNEL but the function is executed with a spin lock taken.
This is wrong and the function must use GFP_ATOMIC instead.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
In my setup data transfer stalls when there's data transmission during
scan. After some testing I found out that using background scan
when connected to makes the problem go away. This is more like
a workaround than a proper fix, but as the stall is so severe the
workaround is justified.
With a dual band card this increases scan time when connected from
1.9s to 4.4s. When not connected the scan time is not affected and
is the same 1.9s.
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Use appropriate hif function directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Endpoint id ffrom htc_packet can be used instead.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Define a hook in ath6kl_hif_ops for hif scatter gather mechanism.
When virtual scatter gather is used, call the respective function
directly.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Last May we started working on cleaning up ath6kl driver which is
currently in staging. The work has happened in a separate
ath6kl-cleanup tree:
http://git.kernel.org/?p=linux/kernel/git/kvalo/ath6kl-cleanup.git;a=summary
After over 1100 (!) patches we have now reached a state where I would
like to start discussing about pushing the driver to the wireless
trees and replacing the staging driver.
The driver is now a lot smaller and looks like a proper Linux driver.
The size of the driver (measured with simple wc -l) dropped from 49
kLOC to 18 kLOC and the number of the .c and .h files dropped from 107
to 22. Most importantly the number of subdirectories reduced from 26
to zero :)
There are two remaining checkpatch warnings in the driver which we
decided to omit for now:
drivers/net/wireless/ath/ath6kl/debug.c:31:
WARNING: printk() should include KERN_ facility level
drivers/net/wireless/ath/ath6kl/sdio.c:527:
WARNING: msleep < 20ms can sleep for up to 20ms;
see Documentation/timers/timers-howto.txt
The driver has endian annotations for all the hardware specific
structures and there are no sparse errors. Unfortunately I don't have
any big endian hardware to test that right now.
We have been testing the driver both on x86 and arm platforms. The
code is also compiled with sparc and parisc cross compilers.
Notable missing features compared to the current staging driver are:
o HCI over SDIO support
o nl80211 testmode
o firmware logging
o suspend support
Testmode, firmware logging and suspend support will be added soon. HCI
over SDIO support will be more difficult as the HCI driver needs to
share code with the wifi driver. This is something we need to research
more.
Also I want to point out the changes I did for signed endian support.
As I wasn't able to find any support for signed endian annotations I
decided to follow what NTFS has done and added my own. Grep for sle16
and sle32, especially from wmi.h.
Various people have been working on the cleanup, the hall of
fame based on number of patches is:
543 Vasanthakumar Thiagarajan
403 Raja Mani
252 Kalle Valo
16 Vivek Natarajan
12 Suraj Sumangala
3 Joe Perches
2 Jouni Malinen
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Raja Mani <rmani@qca.qualcomm.com>
Signed-off-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Suraj Sumangala <surajs@qca.qualcomm.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
Currently ath9k presents the internal calibrated noise floor as channel
noise measurement, however this results in highly chip specific values
that are only useful as relative measurements but do not resemble any
real channel noise values.
In order to give a much better approximation of the real channel noise,
add the difference between the measured noise floor and the nominal
chip specific noise floor to the default minimum channel noise value,
which is currently used to calculate the signal strength from the RSSI
value. This may not be 100% accurate, but it's much better than what's
there before.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When testing for tx power, bypass the default limits.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the previously calculated maximum of all rates instead of just the one
from the lowest rate of the selected PHY mode.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove unnecessary includes from base.h. Add includes to other files as
necessary. Don't include base.h unless needed.
Move declarations for functions in base.c from ath5k.h to base.h.
Use a better named define to protect base.h against double inclusion.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When checking for the band, use channel->band.
Change ath5k_hw_nic_wakeup() and ath5k_channel_ok() to take
ieee80211_channel. Change ath5k_hw_radio_revision() to take
ieee80211_band.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
XR is a proprietary feature of the chipset. It's not supported and
should not be supported.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
struct ath5k_avg_val is unused.
In struct ath5k_hw, lladdr, ah_radar and ah_mac_revision are write-only,
rxbufsize is unused, ah_phy is write-only and referenced by unused
macros.
In struct ath5k_vif, lladdr is write-only.
Remove AR5K_TUNE_RADAR_ALERT, which has no effect.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The driver reads PCI subsystem ID from the PCI configuration register while it's
already stored by the PCI subsystem in the 'subsystem_device' field of 'struct
pci_dev'...
Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
linux/wireless.h and net/iw_handler.h headers are
for wireless extensions only, so mac80211 drivers
shouldn't be including them.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Acked-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We receive many bug reports about system hang during suspend/resume
when ath9k driver is in use. Adrian Chadd remarked that this problem
happens on systems that have ASPM disabled.
To do not hit the bug, skip doing ->config_pci_powersave magic if PCIe
downstream port device, which ath9k device is connected to, has ASPM
disabled.
Bug was introduced by:
commit 53bc7aa08b
Author: Vivek Natarajan <vnatarajan@atheros.com>
Date: Mon Apr 5 14:48:04 2010 +0530
ath9k: Add support for newer AR9285 chipsets.
Patch should address:
https://bugzilla.kernel.org/show_bug.cgi?id=37462https://bugzilla.kernel.org/show_bug.cgi?id=37082https://bugzilla.redhat.com/show_bug.cgi?id=697157
however I did not receive confirmation about that, except from Camilo
Mesias, whose system stops hang regularly with this patch (but still
hangs from time to time, but this is probably some other bug).
Tested-by: Camilo Mesias <camilo@mesias.co.uk>
Cc: stable@kernel.org # 2.6.35+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With an uninitialized chainmask, the per-channel power will only contain
the power limits for a single chain instead of the combined tx power.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Cc: stable@kernel.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (43 commits)
fs: Merge split strings
treewide: fix potentially dangerous trailing ';' in #defined values/expressions
uwb: Fix misspelling of neighbourhood in comment
net, netfilter: Remove redundant goto in ebt_ulog_packet
trivial: don't touch files that are removed in the staging tree
lib/vsprintf: replace link to Draft by final RFC number
doc: Kconfig: `to be' -> `be'
doc: Kconfig: Typo: square -> squared
doc: Konfig: Documentation/power/{pm => apm-acpi}.txt
drivers/net: static should be at beginning of declaration
drivers/media: static should be at beginning of declaration
drivers/i2c: static should be at beginning of declaration
XTENSA: static should be at beginning of declaration
SH: static should be at beginning of declaration
MIPS: static should be at beginning of declaration
ARM: static should be at beginning of declaration
rcu: treewide: Do not use rcu_read_lock_held when calling rcu_dereference_check
Update my e-mail address
PCIe ASPM: forcedly -> forcibly
gma500: push through device driver tree
...
Fix up trivial conflicts:
- arch/arm/mach-ep93xx/dma-m2p.c (deleted)
- drivers/gpio/gpio-ep93xx.c (renamed and context nearby)
- drivers/net/r8169.c (just context changes)
There are only two capabilities we need, and both are trivial to find.
ath5k_hw_hasbssidmask() is true on AR5212, but not on AR5210 or AR5211.
ath5k_hw_hasveol() is true on AR5211 and AR5212, but not on AR5210,
according to the HAL source.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Some devices (e.g. Ubiquiti AirRouter) ship with broken EEPROM chainmask
data, which breaks the initial calibration after a hardware reset.
To fix this, mask the eeprom chainmask with the chainmask of the chip,
and use the chip chainmask if the result is zero.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: "Luis R. Rodriguez" <lrodriguez@atheros.com>
Cc: ath9k-devel@lists.ath9k.org
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Both ath5k_hw and ath5k_softc represent one instance of the hardware.
This duplication is historical and is not needed anymore.
Keep the name "ath5k_hw" for the merged structure and "ah" for the
variable pointing to it. "ath5k_hw" is shorter than "ath5k_softc", more
descriptive and more widely used.
Put the combined structure to ath5k.h where the old ath5k_softc used to
be. Move some code from base.h to ath5k.h as needed.
Remove memory allocation for struct ath5k_hw and the corresponding error
handling. Merge iobase and ah_iobase fields.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Harshal Chhaya discovered during network tests, that
several of his clients dropped-off the network. The
captured packets shows that the beacons sent by the
AP are at a much lower power than the other data
packets.
The reason for this mishap: The driver never updated
the beacon phy register, so all beacons were always
sent at the lowest power.
Reference: http://marc.info/?l=linux-wireless&m=131067225105801
Reported-by: Harshal Chhaya <harshal@gmail.com>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* reserves feature bit for CCA counters
* extends hardware register file definitions
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
Acked-By: christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
For unicast the hardware sometimes reports MIC errors even though the
frame that it received actually contains a valid MIC - on some chips this
can happen frequently enough to trigger TKIP countermeasures.
Fix this issue by not reporting MIC errors for unicast frames with a
valid key, letting mac80211 validate the MIC instead.
Additionally, strip the MIC for all frames that the hardware considers
valid to avoid wasting CPU cycles re-validating it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (21 commits)
slip: fix wrong SLIP6 ifdef-endif placing
natsemi: fix another dma-debug report
sctp: ABORT if receive, reassmbly, or reodering queue is not empty while closing socket
net: Fix default in docs for tcp_orphan_retries.
hso: fix a use after free condition
net/natsemi: Fix module parameter permissions
XFRM: Fix memory leak in xfrm_state_update
sctp: Enforce retransmission limit during shutdown
mac80211: fix TKIP replay vulnerability
mac80211: fix ie memory allocation for scheduled scans
ssb: fix init regression of hostmode PCI core
rtlwifi: rtl8192cu: Add new USB ID for Netgear WNA1000M
ath9k: Fix tx throughput drops for AR9003 chips with AES encryption
carl9170: add NEC WL300NU-AG usbid
cfg80211: fix deadlock with rfkill/sched_scan by adding new mutex
ath5k: fix incorrect use of drvdata in PCI suspend/resume code
ath5k: fix incorrect use of drvdata in sysfs code
Bluetooth: Fix memory leak under page timeouts
Bluetooth: Fix regression with incoming L2CAP connections
Bluetooth: Fix hidp disconnect deadlocks and lost wakeup
...
Instead of using ieee80211_stop_queue, check the configured tx queue
limit before calling ieee80211_get_buffered_bc.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While 32 KHz sleep clock might provide some power saving benefits,
it is also a major source of stability issues, on OpenWrt it produced
some reproducible data bus errors on register accesses on several
different MIPS platforms.
All the Atheros drivers that I can find do not enable this feature,
so it makes sense to leave it disabled in ath5k as well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
enabling the sleep clock alters the AR5K_USEC_32 field, but disabling
it didn't restore it.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During scans the full calibration usually does not make much sense,
PAPD probing and IQ calibration should be deferred until there is
enough time to complete them. Adding 100 ms to the initial full
calibration delay should be enough to do this.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Fixes a division by zero when setting distance before activating the
device for the first time.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Might fix some stability issues on newer chips
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Acked-by: Nick Kossifidis <mickflemm@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rfgain probe is only necessary for OFDM operation on AR5111 and AR5112.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Decryping frames on key_miss handling shouldn't be done for Michael
MIC failed frames as h/w would have already decrypted such frames
successfully anyway.
Also leaving CRC and PHY error(where the frame is going to be dropped
anyway), we are left to prcoess Decrypt error for which s/w decrypt is
selected anway and so having key_miss as a separate check doesn't serve
anything. So making key_miss handling mutually exlusive with other RX
status handling makes much more sense.
This patch addresses an issue with STA not reporting MIC failure events
resulting in STA being disconnected immediately.
Cc: stable@kernel.org
Signed-off-by: Senthil Balasubramanian <senthilb@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR_AN_SYNTH9 is in the analog shift register range and thus needs to be
written using the ath9k_hw_analog_shift_rmw function.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The radio needs twice / four times as much time to stabilize for half/quarter
channels.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Now that the clock rate is initialized properly and SIFS, EIFS, USEC,
slot time and ACK timeout are properly calculated by the generic code,
the 'async FIFO' register hacks are no longer necessary.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Initialize the the clock-to-TSF field of AR_USEC and the SIFS and EIFS time
registers based on the clock rate instead of relying on initvals.
With those changes, some of the hardcoded AR9287 1.3+ specific overrides
can be dropped.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This chip uses the async FIFO feature and runs the MAC at 117 MHz
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Enabling half/quarter rate makes the MAC run at half/quarter clock speed.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
All devices support this, but some disable it using an EEPROM flag
for some reason. Improves 5 GHz performance on those devices.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Use the proper masks for the register instead.
Fixes adding the (still unused) half/quarter PLL flags.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch removes read only registers that cause invalid
address access and also updates index for measurement filter
calibration window size.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The power detector calibration is disabled because this block
doesn't exist in AR9003 based chips and also parallel
calibration is enabled otherwise the calibration will never stop.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The number of temperature reading samples to average
during a Tx packet is decreased to 1 from 2 to improve
5G Tx EVM with chain 0-only mode.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
sc->imask may change if ath5k_set_current_imask() races against itself.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Pavel Roskin <proski@gnu.org>
The reg variable is only used by __raw_writel() and __raw_readl(), which
should guarantee memory access in the right order.
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Implementing this callback function will cause mac80211 refrain from
going to powersave state when there are still untransmitted TX frames
in the queues.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch imports all shared header changes
from carl9170fw.git.
* update copyright boilerplate
* add some more strategic __aligned(4).
* WoWLAN
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While sending aggregated frames in AES, the AR5416 chips
required additional padding b/w subframes. This workaround
is not needed for edma (AR9003 family) chips. With this patch
~4Mbps thoughput improvement was observed in clear environment.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: stable@kernel.org
Reported-by: Mark Davis
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We would free the proper number of curves, but in the wrong
slots, due to a missing level of indirection through
the pdgain_idx table.
It's simpler just to try to free all four slots, so do that.
Cc: stable@kernel.org
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When no interface has been brought up, the chip's power
state continued as AWAKE. So during resume, the chip never
been powered up.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The received tx status of aggregated frame without BlockAck may
cause deaf state in AR5416 cards. So the driver does a reset to
recover. When this happens, we release the pcu_lock before doing
a reset as ath_rest acquires pcu_lock. This is ugly and also not
atomic. Fixing this addresses the TX DMA failure also.
ath_tx_complete_aggr can be called from different paths which
takes different variants of spin_lock. This patch also addresses
the following warning.
WARNING: at kernel/timer.c:1011 del_timer_sync+0x4e/0x50()
Call Trace:
<IRQ> [<ffffffff8104be3a>] warn_slowpath_common+0x7a/0xb0
[<ffffffff8104be85>] warn_slowpath_null+0x15/0x20
[<ffffffff8105915e>] del_timer_sync+0x4e/0x50
[<ffffffffa03726be>] ath_reset+0x3e/0x210 [ath9k]
[<ffffffff8135cdaf>] ? _raw_spin_unlock_bh+0x1f/0x30
[<ffffffffa037760a>] ath_tx_complete_aggr.isra.26+0x54a/0xa40 [ath9k]
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Cc: muddin@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The edma based (AR9003 family) chips update tx status
descriptors in a common ring buffer for all transmitted
frames. Whenever tx interrupt is raised, the descriptors
are processed and tx status index is moved.
The complete tx stauts ring are updated with beacons tx status
when there are no data frames to be sent for a period of time.
In this state, transmitting data frames causes the driver to
wait for the tx status on an incorrect tx status index though
the status was updated by hw properly. The driver detects this
condition as a h/w hang and does unnecessary chip resets.
This issue was orginally reported in adhoc mode while sending
frames after an idle time.
Signed-off-by: Rajkumar Manoharan <rmanohar@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Move all that mac80211 has into the generic
ieee80211.h header file and use them. At the
same time move them from mask+shift to just
bits and rename them for consistent names.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch adds a callback to ath9k_platform_data. If the
callback is provided by the platform code, then it can be
used to hard reset the WMAC device.
The callback is required for doing a hard reset of the AR9330
chips to get them working again after a hang.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The patch adds the missing configuration code for diversity
group 1.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The current values must be used only on AR9485 chips. Other chips
requires different values.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The 'ar9003_hw_antdiv_comb_conf_get' function sets div_group to 2
however that value is not used in 'ath_ant_div_comb_alt_check'.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
A multiplication is missing from the current formula.
Cc: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9330 1.0 and 1.1 are using the same revision,
thus it is not possible to distinguish the two chips.
The platform setup code can distinguish the chips based
on the SoC revision.
Add a callback function to ath9k_platform_data in order
to allow getting the revision number from the platform code.
Signed-off-by: Gabor Juhos <juhosg@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
higher the chainmask, lesser the power_delta to be added
to the paprd_training_power
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove linux/mm.h inclusion from netdevice.h -- it's unused (I've checked manually).
To prevent mm.h inclusion via other channels also extract "enum dma_data_direction"
definition into separate header. This tiny piece is what gluing netdevice.h with mm.h
via "netdevice.h => dmaengine.h => dma-mapping.h => scatterlist.h => mm.h".
Removal of mm.h from scatterlist.h was tried and was found not feasible
on most archs, so the link was cutoff earlier.
Hope people are OK with tiny include file.
Note, that mm_types.h is still dragged in, but it is a separate story.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing else is freeing it, and this mirrors the error handling path
already in ath5k_init_softc.
https://bugzilla.kernel.org/show_bug.cgi?id=37592
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reported-by: Tsyvarev Andrey <tsyvarev@ispras.ru>
checking the status of PAPRD_AGC2_POWER(Log(ADC_power) measured after
last gain-change in dB) field suggests whether the PAPRD is completely/properly
done. This is an additional check apart from polling for PAPRD done bit being set.
Susinder suggests that the ideal power range value should be
0xf0 to 0xfe. With AR9382 we do have the values in this range. to have a
common check for all platforms we take agc2_power should be atleast greater
than 0xe0
Cc: susinder@qca.qualcomm.com
Cc: senthilb@qca.qualcomm.com
Cc: kmuthusa@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when the AP is configured with HT40/2.4GHz and when PAPRD is enabled in station
we have PAPRD training frames never sent out because of the following
failure "PAPRD target power delta out of range". This consistently happens
in channel 10,11 in Over The Air testing and rarely in channel 6 under wired
setup.
the reason behind this issue is all the HT40 rates target power
are 0 when we operate in channel 10/11 at 2.4GHz
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Many stupid corrections of duplicated includes based on the output of
scripts/checkincludes.pl.
Signed-off-by: Vitaliy Ivanov <vitalivanov@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Move an extern variable declaration to a header file. Prefix all
functions with "ath5k_". Make ath5k_intr() static. Remove unneeded
forward declarations. Remove pointless "extern" in a function
declaration.
Signed-off-by: Pavel Roskin <proski@gnu.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
during suspend/resume ath9k_stop will always call ath_radio_disable
which will inturn call ath9k_hw_configpcipowersave, so no need to call
it explicitly in ath9k_stop
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add few debug messages for some of the possible scenarios
where we can detect PAPRD failures. this will help us to be
sure that we had really enabled PAPRD
Cc: susinder@qca.qualcomm.com
Cc: senthilb@qca.qualcomm.com
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* remove interrupt.g inclusion from netdevice.h -- not needed
* fixup fallout, add interrupt.h and hardirq.h back where needed.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Disable fast channel change by default on AR2413/AR5413 due to
some bug reports (it still works for me but it's better to be safe).
Add a module parameter "fastchanswitch" in case anyone wants to enable
it and play with it.
Signed-off-by: Nick Kossifidis <mickflemm@gmail.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
the training power calculation indirectly depends on target power under
some scenarios, unless we have a valid training power, the PAPRD frames
won't be sent out. so when we get an invalid training power, its better
to display them before returning back.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this helps the user to start/stop ANI dynamically.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This fix ensure the timers to be set at beacon interval boundaries.
Without this change timers can be set improperly resulting in the absence of beacons.
Signed-off-by: Fabrice Deyber <fabricedeyber@agilemesh.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In PAPRD table initialization path we do some register read, so
make sure the chip is awake during that. Currently PAPRD is disabled.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Configure ibss node's bss_changes under BSS_CHANGED_IBSS.
And also start/stop ani timer only if the station join/leave
the group.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Earlier beacon_interval is used to hold interval value and
some flags (ATH9K_BEACON_ENA &ATH9K_BEACON_PERIOD). So to
extract interval ATH9K_BEACON_PERIOD is used. Those flags
were completely removed. So masking beacon_interval is
not required.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
EDMA based chips (AR9380+) have 8 Tx FIFO slots, which are used to fix the
tx queue start/stop race conditions which have to be worked around for
earlier chips by keeping the last descriptor in the queue. The current code
stores all frames that do not fit onto the 8 FIFO slots in a separate
list. Whenever a FIFO slot is freed up, the next frame (or A-MPDU) from the
pending queue gets moved to that slot.
This process is not only inefficient, but also unnecessary. The code can
be improved visibly by keeping the pending queue fully linked, and moving
the contents of the entire queue to a FIFO slot as it becomes available.
This patch makes the necessary changes for that and also merges some code
that was duplicated for EDMA vs non-EDMA. It changes txq->axq_link to point
to the last descriptor instead of the link pointer, so that
ath9k_hw_set_desc_link can be used, which works on all chips.
With this patch, a small performance increase for non-aggregated traffic
was observed on AR9380 based embedded hardware.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This is the same fix as
commit 841051602e
Author: Matteo Croce <technoboy85@gmail.com>
Date: Fri Dec 3 02:25:08 2010 +0100
The ath9k driver subtracts 3 dBm to the txpower as with two radios the
signal power is doubled.
The resulting value is assigned in an u16 which overflows and makes
the card work at full power.
in two more places. I grepped the ath tree and didn't find any others.
Cc: stable@kernel.org
Signed-off-by: Daniel Halperin <dhalperi@cs.washington.edu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The AR9287 calibration code was not being called because of an
incorrect MAC revision check.
This forced the AR9287 to use the AR9285 initial calibration code and
bypass the AR9287 code entirely.
Signed-off-by: Adrian Chadd <adrian@freebsd.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We make oldconfig every time when a new kernel arrives, but
if we don't have such a device(I guess this is the most common
case for a new device), the default value should be 'n' so
that the kernel size we build doesn't grow up too much quickly.
For anyone who has the device, it is OK for them to turn it on
by themselves.
Cc: "John W. Linville" <linville@tuxdriver.com>
Cc: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: Tao Ma <boyu.mt@taobao.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Whenever there is a channel width change from 40 Mhz to 20 Mhz,
the hardware is reconfigured to ht20. Meantime before doing
the rate control updation, the packets are being transmitted are
selected rate with IEEE80211_TX_RC_40_MHZ_WIDTH.
While transmitting ht40 rate packets in ht20 mode is causing
baseband panic with AR9003 based chips.
==== BB update: BB status=0x02001109 ====
ath: ** BB state: wd=1 det=1 rdar=0 rOFDM=1 rCCK=1 tOFDM=0 tCCK=0 agc=2
src=0 **
ath: ** BB WD cntl: cntl1=0xffff0085 cntl2=0x00000004 **
ath: ** BB mode: BB_gen_controls=0x000033c0 **
ath: ** BB busy times: rx_clear=99%, rx_frame=0%, tx_frame=0% **
ath: ==== BB update: done ====
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While receiving unsupported rate frame rx state machine
gets into a state 0xb and if phy_restart happens in that
state, BB would go hang. If RXSM is in 0xb state after
first bb panic, ensure to disable the phy_restart.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Resetting hardware helps to recover from baseband
hang/panic for AR9003 based chips.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (39 commits)
b43: fix comment typo reqest -> request
Haavard Skinnemoen has left Atmel
cris: typo in mach-fs Makefile
Kconfig: fix copy/paste-ism for dell-wmi-aio driver
doc: timers-howto: fix a typo ("unsgined")
perf: Only include annotate.h once in tools/perf/util/ui/browsers/annotate.c
md, raid5: Fix spelling error in comment ('Ofcourse' --> 'Of course').
treewide: fix a few typos in comments
regulator: change debug statement be consistent with the style of the rest
Revert "arm: mach-u300/gpio: Fix mem_region resource size miscalculations"
audit: acquire creds selectively to reduce atomic op overhead
rtlwifi: don't touch with treewide double semicolon removal
treewide: cleanup continuations and remove logging message whitespace
ath9k_hw: don't touch with treewide double semicolon removal
include/linux/leds-regulator.h: fix syntax in example code
tty: fix typo in descripton of tty_termios_encode_baud_rate
xtensa: remove obsolete BKL kernel option from defconfig
m68k: fix comment typo 'occcured'
arch:Kconfig.locks Remove unused config option.
treewide: remove extra semicolons
...
otherwise we will get deadbeef when the station is in idle state
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
rounding up the delta between last-beacon-tsf and tsf to intval is wrong
and can lead to misconfigured timers which breaks beacon transmission.
Fix this by adding intval and subtracting the offset of the tsf within the
current slot.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The WMI tx status event timeout was not aligning with the
TX cleanup timer threshold value. Fix this to handle dropped
packets.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Reduce the credit size for UB94/95 to fix target hangs.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Commit "ath9k_htc: Fix AMPDU subframe handling" registered the maximum
subframe limit of the driver with mac80211, which was used in ADDBA
negotiation. While technically correct, this causes inter-operability issues
with a few APs. Revert to the older behavior to fix this.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The BSSID/AID has to be set for the first associated station interface.
Subsequent interfaces may move out of assoc/disassoc status, in which
case, the BSSID has to be re-calculated from the available interfaces.
Also, ANI should be enabled or disabled based on the current opmode.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Choose the MY_BEACON filter only in case of a single interface.
Also, set the ATH9K_RX_FILTER_MCAST_BCAST_ALL filter in case
of interfaces.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The FW does absolutely nothing with the station flags,
so remove them. But keep the field around since it might
come in handy in the future.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove all the unsupported modes like FH, TURBO etc.
Since this requires a FW update, increase the fw version to 1.3
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In ad-hoc mode, beacon timers are configured differently compared to AP
mode, and (depending on the scenario) can vary enough to make the beacon
tasklet not detect slot 0 based on the TSF.
Since staggered beacons are not (and cannot be) used in ad-hoc mode, it
makes more sense to just hardcode slot 0 here, avoiding unnecessary
TSF reads and calculations.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In order to provide multiple interfaces for a single device,
the driver will be required to advertise all possible
interface configurations to the stack.
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
we are not doing anything by tracking the number of pending frames.
bail out when we first find a pending frame in any one of the 10 queues.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
some times the rssi control descriptor for the main antenna may be
negative like that of alternate antenna, hence before incrementing
packet counts/rssi of main/alternate antenna make sure both main_rssi
and alt_rssi are positive only. this avoids wrong selection of antenna
due to diversity
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
configure fast diversity bias based on the antenna diversity group and
based on main/alt LNA configurations. also configure main antenna and
alternate antenna to gain-table 0 for diversity group 2(AR9485)
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
for the diversity group 2(AR9485) we swap the LNA's of main/ALT antenna
based on alternate antenna's rssi average in comparision with main
antenna's rssi, while for AR9285(antenna diversity group 0)we still
follow the older method of looking at the packet count in alternate
antenna
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
AR9285 belongs to diversity group 0 and AR9485 belongs to diversity
group 2. Based on the diversity group we configure certain antenna
diversity paramaters such as lna1_lna2_delta and fast diversity
bias values. For AR9485 we have some gain table parameter which
selects the gain table 0/1 for main and alternate antenna
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
these are the two important modules that will be called by the antenna
diversity algorithm module in the rx. this will continuosly configure
the hardware based on the current diversity status obtained
from the algorithm
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
* enable LNA-diversity, fast-diversity for AR9485 based on
the value read from EEPROM content
* if antenna diversity/combining is supported, set LNA1 for the main
antenna and LNA2 for the alternate antenna based on the new diversity
algorithm
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Cc: Luis Rodriguez <Luis.Rodriguez@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
define few registers and macros to configure/enable Antenna diversity
parameters in AR9485
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
read antenna diversity and combining information from the EEPROM.
Enable antenna diversity/combining feature only when both LNA
diversity and fast diversity are supported
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Tested-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this is necessary to support Antenna diversity and combining in new chip
sets such as AR9485, previously Antenna diversity support is available
only in AR9285
Cc: Gabriel Tseng <Gabriel.Tseng@Atheros.com>
Cc: Senthilkumar Balasubramanian <Senthilkumar.Balasubramanian@Atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
XB113 (AR9380) 3x3 SB 5G only cards were failing to connect to APs
due to incorrect xpabiaslevel configuration. fix it.
Cc: stable@kernel.org
Cc: Ray Li <ray.li@greenwavereality.com>
Cc: Kathy Giori <kathy.giori@atheros.com>
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: compat@orbit-lab.org
Signed-off-by: Senthil Balasubramanian <senthilkumar@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The XB113 cards are single band, 5 GHz-only, but the
default settings were configured to assume it was dual
band. Users of these cards then would see 2.4 GHz channels
but you would never get any scan results from these channels
given that the radio is not present.
Cc: stable@kernel.org
Cc: Fiona Cain <Fiona.Cain@atheros.com>
Cc: Ray Li <ray.li@greenwavereality.com>
Cc: Kathy Giori <kathy.giori@atheros.com>
Cc: Aeolus Yang <aeolus.yang@atheros.com>
Cc: Dan Friedman <dan.friedman@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only leave filtering enabled for AP or VLAN interfaces, clear the
destination mask for all other interfaces.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Reported-by: Ben Greear <greearb@candelatech.com>
Tested-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This was introduced in 2.6.39-rc1 it seems.
Signed-off-by: Ben Greear <greearb@candelatech.com>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Mesh beaconing on ath9k was broken by this commit:
commit 4801416c76
Author: Ben Greear <greearb@candelatech.com>
Date: Sat Jan 15 19:13:48 2011 +0000
This patch assigns the right opmode when the device is used in mesh
mode.
Reported-by: Fabrice Deyber fabricedeyber@agilemesh.com
Signed-off-by: Javier Cardona <javier@cozybit.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This beacon rssi will be used to set noisefloor during ani reset.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The average beacon rssi which will be used by ani is not updated
in adhoc mode.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
By changing DCU backoff threshold for AR9340 to 1, helps to
reduce rx overrurns seen while running bidirectional traffic.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
currently ath9k_hw_getchan_noise is not used anywhere
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
tx.c: In function ‘carl9170_tx_accounting_free’:
tx.c:159:28: warning: variable ‘txinfo’ set but not used
tx.c: In function ‘carl9170_tx_status_process_ampdu’:
tx.c:383:27: warning: variable ‘ar_info’ set but not used
tx.c: In function ‘__carl9170_tx_process_status’:
tx.c:626:27: warning: variable ‘arinfo’ set but not used
tx.c: In function ‘carl9170_tx_ampdu_queue’:
tx.c:1324:15: warning: variable ‘max’ set but not used
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Processing TSF out of range before RX helps to update beacon
timers so early in the succeeding rx process.
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The assumsion is that while processing ath9k tasklet,
interrupts were already disabled and it will be enabled
at the completion of ath9k tasklet. But whenever TSFOOR is raised,
the driver configures the beacon timers after having received a
beacon frame from the AP which inturn enables the interrupts.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
during suspend/S3 state drv_flush is called from mac80211 irrespective of
interface count. In ath9k we queue a work in ath9k_flush which we expect
to be cancelled in the drv_stop call back. during suspend process mac80211
calls drv_stop only when the interface count(local->count) is non-zero.
unfortunately when the network manager is enabled, drv_flush is called
while drv_stop is not called as local->count reaches '0'.
So fix this by simply checking for the device presence in the
drv_flush call back in the driver before queueing work or anything else.
this patch fixes the following WARNING
Call Trace:
[<c014c6e2>] warn_slowpath_common+0x72/0xa0
[<fc133f99>] ? ieee80211_can_queue_work+0x39/0x50 [mac80211]
[<fc133f99>] ? ieee80211_can_queue_work+0x39/0x50 [mac80211]
[<c014c75b>] warn_slowpath_fmt+0x2b/0x30
[<fc133f99>] ieee80211_can_queue_work+0x39/0x50 [mac80211]
[<fc134ed1>] ieee80211_queue_delayed_work+0x21/0x50 [mac80211]
[<fc1e5b22>] ath_tx_complete_poll_work+0xb2/0x100 [ath9k]
[<c016399e>] run_workqueue+0x8e/0x150
[<fc1e5a70>] ? ath_tx_complete_poll_work+0x0/0x100 [ath9k]
[<c0163ae4>] worker_thread+0x84/0xe0
[<c0167a60>] ? autoremove_wake_function+0x0/0x50
[<c0163a60>] ? worker_thread+0x0/0xe0
[<c01677d4>] kthread+0x74/0x80
[<c0167760>] ? kthread+0x0/0x80
[<c0104087>] kernel_thread_helper+0x7/0x10
---[ end trace 2aff81010df9215b ]---
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
With AR9003 at about ~ 10 feet from an AP that uses RTS / CTS you
will be able to associate but not not get data through given that
the power for the rates used was set too low. This increases the
power and permits data connectivity at longer distances from
access points when connected with HT40. Without this you will not
get any data through when associated to APs configured in HT40
at about more than 10 feet away.
Cc: stable@kernel.org
Cc: Fiona Cain <fcain@atheros.com>
Cc: Zhen Xie <Zhen.Xie@Atheros.com>
Cc: Kathy Giori <kathy.giori@atheros.com>
Cc: Neha Choksi <neha.choksi@atheros.com>
Cc: Wayne Daniel <wayne.daniel@atheros.com>
Cc: Gaurav Jauhar <gaurav.jauhar@atheros.com>
Cc: Samira Naraghi <samira.naraghi@atheros.com>
CC: Ashok Chennupati <ashok.chennupati@atheros.com>
Cc: Lance Zimmerman <lance.zimmerman@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
At present the noise floor calibration is processed in supported
control and extension chains rather than required chains.
Unnccesarily doing nfcal in all supported chains leads to
invalid nf readings on extn chains and these invalid values
got updated into history buffer. While loading those values
from history buffer is moving the chip to deaf state.
This issue was observed in AR9002/AR9003 chips while doing
associate/dissociate in HT40 mode and interface up/down
in iterative manner. After some iterations, the chip was moved
to deaf state. Somehow the pci devices are recovered by poll work
after chip reset. Raading the nf values in all supported extension chains
when the hw is not yet configured in HT40 mode results invalid values.
Cc: stable@kernel.org
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Currently, the driver only disable multicast filtering when the
FIF_ALLMULTI driver flag has been just set (ie,
if changed_flags& FIF_ALLMULTI and *new_flags& FIF_ALLMULTI) or else
it will reenable multicast filtering.
But next time, this condition will be false and multicast filtering
will be reenabled, even through FIF_ALLMULTI is still set.
This mean that allmulticast only works for less than two minutes in
ad-hoc mode. This patch fixes that to disable multicast filtering
as long as FIF_ALLMULTI is set.
Signed-off-by: Nicolas Cavallari <cavallar@lri.fr>
Acked-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
when aggregation protection mode is enabled the hardware needs
to send RTS/CTS for each HT frame. Currently its disabled so
remove the unused call backs.
Signed-off-by: Mohammed Shafi Shajakhan <mshajakhan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
While draining the txq in flush, the buffers can be
added into the tx queue by tx_tasklet which leads to
unneccesary chip reset.
This issue was originially found with AR9382 and
running heavy uplink udp traffic with higher bandwidth
and doing frequent bgscan.
Cc: stable@kernel.org
Signed-off-by: Vasanthakumar Thiagarajan <vasanth@atheros.com>
Signed-off-by: Rajkumar Manoharan <rmanoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Remove all the convoluted hacks in the driver and simplify things
by making use of mac80211's LED triggers.
Signed-off-by: Sujith Manoharan <Sujith.Manoharan@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Senthil Balasubramanian