setup_conf in raid1.c uses conf->raid_disks before assigning
a value. It is used when including 'Replacement' devices.
The consequence is that assembling an array which contains a
replacement will misbehave and either not include the replacement, or
not include the device being replaced.
Though this doesn't lead directly to data corruption, it could lead to
reduced data safety.
So use mddev->raid_disks, which is initialised, instead.
Bug was introduced by commit c19d57980b
md/raid1: recognise replacements when assembling arrays.
in 3.3, so fix is suitable for 3.3.y thru 3.6.y.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
in:
fe86cdce block: do not artificially constrain max_sectors for stacking drivers
max_sectors defaults to UINT_MAX. md faulty wasn't using
disk_stack_limits(), so inherited this large value as well.
This triggered a bug in XFS when stressed over md_faulty, when
a very large bio_alloc() failed.
That was on an older kernel, and I can't reproduce exactly the
same thing upstream, but I think the fix is appropriate in any
case.
Thanks to Mike Snitzer for pointing out the problem.
Signed-off-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
"discard" support, some dm-raid improvements and other assorted
bits and pieces.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=XRmL
-----END PGP SIGNATURE-----
Merge tag 'md-3.7' of git://neil.brown.name/md
Pull md updates from NeilBrown:
- "discard" support, some dm-raid improvements and other assorted bits
and pieces.
* tag 'md-3.7' of git://neil.brown.name/md: (29 commits)
md: refine reporting of resync/reshape delays.
md/raid5: be careful not to resize_stripes too big.
md: make sure manual changes to recovery checkpoint are saved.
md/raid10: use correct limit variable
md: writing to sync_action should clear the read-auto state.
Subject: [PATCH] md:change resync_mismatches to atomic64_t to avoid races
md/raid5: make sure to_read and to_write never go negative.
md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
md/raid5: protect debug message against NULL derefernce.
md/raid5: add some missing locking in handle_failed_stripe.
MD: raid5 avoid unnecessary zero page for trim
MD: raid5 trim support
md/bitmap:Don't use IS_ERR to judge alloc_page().
md/raid1: Don't release reference to device while handling read error.
raid: replace list_for_each_continue_rcu with new interface
add further __init annotations to crypto/xor.c
DM RAID: Fix for "sync" directive ineffectiveness
DM RAID: Fix comparison of index and quantity for "rebuild" parameter
DM RAID: Add rebuild capability for RAID10
DM RAID: Move 'rebuild' checking code to its own function
...
Use the recently-added bio front_pad field to allocate struct dm_target_io.
Prior to this patch, dm_target_io was allocated from a mempool. For each
dm_target_io, there is exactly one bio allocated from a bioset.
This patch merges these two allocations into one allocation: we create a
bioset with front_pad equal to the size of dm_target_io so that every
bio allocated from the bioset has sizeof(struct dm_target_io) bytes
before it. We allocate a bio and use the bytes before the bio as
dm_target_io.
_tio_cache is removed and the tio_pool mempool is now only used for
request-based devices.
This idea was introduced by Kent Overstreet.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: Kent Overstreet <koverstreet@google.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: tj@kernel.org
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Bill Pemberton <wfp5p@viridian.itc.virginia.edu>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The bio prison code will be useful to other future DM targets so
move it to a separate module.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The bio prison code will be useful to share with future DM targets.
Prepare to move this code into a separate module, adding a dm prefix
to structures and functions that will be exported.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Support discards when the pool's block size is not a power of 2.
The block layer assumes discard_granularity is a power of 2 (in
blkdev_issue_discard), so we set this to the largest power of 2 that is
a divides into the number of sectors in each block, but never less than
DATA_DEV_BLOCK_SIZE_MIN_SECTORS.
This patch eliminates the "Discard support must be disabled when the
block size is not a power of 2" constraint that was imposed in commit
55f2b8b ("dm thin: support for non power of 2 pool blocksize"). That
commit was incomplete: using a block size that is not a power of 2
shouldn't mean disabling discard support on the device completely.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Convert cpu_to_le32(le32_to_cpu(E1) + E2) to use le32_add_cpu().
dpatch engine is used to auto generate this patch.
(https://github.com/weiyj/dpatch)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use the ACCESS_ONCE macro in dm-bufio and dm-verity where a variable
can be modified asynchronously (through sysfs) and we want to prevent
compiler optimizations that assume that the variable hasn't changed.
(See Documentation/atomic_ops.txt.)
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use list_move() instead of list_del() + list_add().
spatch with a semantic match was used to find this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The mpio dereference should be moved below the BUG_ON NULL test
in multipath_end_io().
spatch with a semantic match was used to found this.
(http://coccinelle.lip6.fr/)
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If 'resync_max' is set to 0 (as is often done when starting a
reshape, so the mdadm can remain in control during a sensitive
period), and if the reshape request is initially delayed because
another array using the same array is resyncing or reshaping etc,
when user-space cannot easily tell when the delay changes from being
due to a conflicting reshape, to being due to resync_max = 0.
So introduce a new state: (curr_resync == 3) to reflect this, make
sure it is visible both via /proc/mdstat and via the "sync_completed"
sysfs attribute, and ensure that the event transition from one delay
state to the other is properly notified.
Signed-off-by: NeilBrown <neilb@suse.de>
When a RAID5 is reshaping, conf->raid_disks is increased
before mddev->delta_disks becomes zero.
This can result in check_reshape calling resize_stripes with a
number that is too large. This particularly happens
when md_check_recovery calls ->check_reshape().
If we use ->previous_raid_disks, we don't risk this.
Signed-off-by: NeilBrown <neilb@suse.de>
If you make an array bigger but suppress resync of the new region with
mdadm --grow /dev/mdX --size=max --assume-clean
then stop the array before anything is written to it, the effect of
the "--assume-clean" is lost and the array will resync the new space
when restarted.
So ensure that we update the metadata in the case.
Reported-by: Sebastian Riemer <sebastian.riemer@profitbricks.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Clang complains that we are assigning a variable to itself. This should
be using bad_sectors like the similar earlier check does.
Bug has been present since 3.1-rc1. It is minor but could
conceivably cause corruption or other bad behaviour.
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In some cases array are started in 'read-auto' state where in
nothing gets written to any device until the array is written
to. The purpose of this is to make accidental auto-assembly
of the wrong arrays less of a risk, and to allow arrays to be
started to read suspend-to-disk images without actually changing
anything (as might happen if the array were dirty and a
resync seemed necessary).
Explicitly writing the 'sync_action' for a read-auto array currently
doesn't clear the read-auto state, so the sync action doesn't
happen, which can be confusing.
So allow any successful write to sync_action to clear any read-auto
state.
Reported-by: Alexander Kühn <alexander.kuehn@nagilum.de>
Signed-off-by: NeilBrown <neilb@suse.de>
Now that multiple threads can handle stripes, it is safer to
use an atomic64_t for resync_mismatches, to avoid update races.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
to_read and to_write are part of the result of analysing
a stripe before handling it.
Their use is to avoid some loops and tests if the values are
known to be zero. Thus it is not a problem if they are a
little bit larger than they should be.
So decrementing them in handle_failed_stripe serves little value, and
due to races it could cause some loops to be skipped incorrectly.
So remove those decrements.
Reported-by: "Jianpeng Ma" <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
The pr_debug in add_stripe_bio could race with something
changing *bip, so it is best to hold the lock until
after the pr_debug.
Reported-by: "Jianpeng Ma" <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We really should hold the stripe_lock while accessing
'toread' else we could race with add_stripe_bio and corrupt
a list.
Reported-by: "Jianpeng Ma" <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We want to avoid zero discarded dev page, because it's useless for discard.
But if we don't zero it, another read/write hit such page in the cache and will
get inconsistent data.
To avoid zero the page, we don't set R5_UPTODATE flag after construction is
done. In this way, discard write request is still issued and finished, but read
will not hit the page. If the stripe gets accessed soon, we need reread the
stripe, but since the chance is low, the reread isn't a big deal.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Discard for raid4/5/6 has limitation. If discard request size is
small, we do discard for one disk, but we need calculate parity and
write parity disk. To correctly calculate parity, zero_after_discard
must be guaranteed. Even it's true, we need do discard for one disk
but write another disks, which makes the parity disks wear out
fast. This doesn't make sense. So an efficient discard for raid4/5/6
should discard all data disks and parity disks, which requires the
write pattern to be (A, A+chunk_size, A+chunk_size*2...). If A's size
is smaller than chunk_size, such pattern is almost impossible in
practice. So in this patch, I only handle the case that A's size
equals to chunk_size. That is discard request should be aligned to
stripe size and its size is multiple of stripe size.
Since we can only handle request with specific alignment and size (or
part of the request fitting stripes), we can't guarantee
zero_after_discard even zero_after_discard is true in low level
drives.
The block layer doesn't send down correctly aligned requests even
correct discard alignment is set, so I must filter out.
For raid4/5/6 parity calculation, if data is 0, parity is 0. So if
zero_after_discard is true for all disks, data is consistent after
discard. Otherwise, data might be lost. Let's consider a scenario:
discard a stripe, write data to one disk and write parity disk. The
stripe could be still inconsistent till then depending on using data
from other data disks or parity disks to calculate new parity. If the
disk is broken, we can't restore it. So in this patch, we only enable
discard support if all disks have zero_after_discard.
If discard fails in one disk, we face the similar inconsistent issue
above. The patch will make discard follow the same path as normal
write request. If discard fails, a resync will be scheduled to make
the data consistent. This isn't good to have extra writes, but data
consistency is important.
If a subsequent read/write request hits raid5 cache of a discarded
stripe, the discarded dev page should have zero filled, so the data is
consistent. This patch will always zero dev page for discarded request
stripe. This isn't optimal because discard request doesn't need such
payload. Next patch will avoid it.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When we get a read error, we arrange for raid1d to handle it.
Currently we release the reference on the device. This can result
in
conf->mirrors[read_disk].rdev
being NULL in fix_read_error, if the device happens to get removed
before the read error is handled.
So instead keep the reference until the read error has been fully
handled.
Reported-by: hank <pyu@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This patch replaces list_for_each_continue_rcu() with
list_for_each_entry_continue_rcu() to save a few lines
of code and allow removing list_for_each_continue_rcu().
Reviewed-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Signed-off-by: Michael Wang <wangyun@linux.vnet.ibm.com>
Signed-off-by: NeilBrown <neilb@suse.de>
There are two table arguments that can be given to a DM RAID target
that control whether the array is forced to (re)synchronize or skip
initialization: "sync" and "nosync". When "sync" is given, we set
mddev->recovery_cp to 0 in order to cause the device to resynchronize.
This is insufficient if there is a bitmap in use, because the array
will simply look at the bitmap and see that there is no recovery
necessary.
The fix is to skip over the loading of the superblocks when "sync" is
given, causing new superblocks to be written that will force the array
to go through initialization (i.e. synchronization).
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Fix comparison of index and quantity for "rebuild" parameter
The "rebuild" parameter takes an index argument that starts counting from
zero. The conditional used to validate the index was using '>' rather than
'>=', leaving the door open for an index value that would be 1 too large.
Reported-by: Neil Brown <neilb@suse.de>
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Add code to validate replacement slots for RAID10 arrays
RAID10 can handle 'copies - 1' failures for each mirror group. This code
ensures the user has provided a valid array - one whose devices specified for
rebuild do not exceed the amount of redundancy available.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
DM RAID: Move chunk of code to it's own function
The code that checks whether device replacements/rebuilds are possible given
a specific RAID type is moved to it's own function. It will further expand
when the code to check RAID10 is added. A separate function makes it easier
to read.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
MD RAID10: Fix a couple potential kernel panics if RAID10 is used by dm-raid
When device-mapper uses the RAID10 personality through dm-raid.c, there is no
'gendisk' structure in mddev and some sysfs information is also not populated.
This patch avoids touching those non-existent structures.
Signed-off-by: Jonathan Brassow <jbrassow@rehdat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Some ioctls don't need to take the mutex and doing so can cause
a delay as it is held during super-block update.
So move those ioctls out of the mutex and rely on rcu locking
to ensure we don't access stale data.
Signed-off-by: NeilBrown <neilb@suse.de>
Change the thread parameter, so the thread can carry extra info. Next patch
will use it.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
queuing writes to the md thread means that all requests go through the
one processor which may not be able to keep up with very high request
rates.
So use the plugging infrastructure to submit all requests on unplug.
If a 'schedule' is needed, we fall back on the old approach of handing
the requests to the thread for it to handle.
This is nearly identical to a recent patch which provided similar
functionality to RAID1.
Signed-off-by: NeilBrown <neilb@suse.de>
This makes md raid 10 support TRIM.
If one disk supports discard and another not, or one has
discard_zero_data and another not, there could be inconsistent between
data from such disks. But this should not matter, discarded data is
useless. This will add extra copy in rebuild though.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This makes md raid 1 support TRIM.
If one disk supports discard and another not, or one has discard_zero_data and
another not, there could be inconsistent between data from such disks. But this
should not matter, discarded data is useless. This will add extra copy in rebuild
though.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
According to the comment in linear_stop function
rcu_dereference in linear_start and linear_stop functions
occurs under reconfig_mutex. The patch represents this
agreement in code and prevents lockdep complaint.
Found by Linux Driver Verification project (linuxtesting.org)
Signed-off-by: Denis Efremov <yefremov.denis@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Pull block IO update from Jens Axboe:
"Core block IO bits for 3.7. Not a huge round this time, it contains:
- First series from Kent cleaning up and generalizing bio allocation
and freeing.
- WRITE_SAME support from Martin.
- Mikulas patches to prevent O_DIRECT crashes when someone changes
the block size of a device.
- Make bio_split() work on data-less bio's (like trim/discards).
- A few other minor fixups."
Fixed up silent semantic mis-merge as per Mikulas Patocka and Andrew
Morton. It is due to the VM no longer using a prio-tree (see commit
6b2dbba8b6ac: "mm: replace vma prio_tree with an interval tree").
So make set_blocksize() use mapping_mapped() instead of open-coding the
internal VM knowledge that has changed.
* 'for-3.7/core' of git://git.kernel.dk/linux-block: (26 commits)
block: makes bio_split support bio without data
scatterlist: refactor the sg_nents
scatterlist: add sg_nents
fs: fix include/percpu-rwsem.h export error
percpu-rw-semaphore: fix documentation typos
fs/block_dev.c:1644:5: sparse: symbol 'blkdev_mmap' was not declared
blockdev: turn a rw semaphore into a percpu rw semaphore
Fix a crash when block device is read and block size is changed at the same time
block: fix request_queue->flags initialization
block: lift the initial queue bypass mode on blk_register_queue() instead of blk_init_allocated_queue()
block: ioctl to zero block ranges
block: Make blkdev_issue_zeroout use WRITE SAME
block: Implement support for WRITE SAME
block: Consolidate command flag and queue limit checks for merges
block: Clean up special command handling logic
block/blk-tag.c: Remove useless kfree
block: remove the duplicated setting for congestion_threshold
block: reject invalid queue attribute values
block: Add bio_clone_bioset(), bio_clone_kmalloc()
block: Consolidate bio_alloc_bioset(), bio_kmalloc()
...
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
Of particular note, are fixes to the thin target's discard support,
which I hope is finally working correctly; and fixes for multipath
ioctls and device limits when there are no paths.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=J1f2
-----END PGP SIGNATURE-----
Merge tag 'dm-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull dm fixes from Alasdair G Kergon:
"A few fixes for problems discovered during the 3.6 cycle.
Of particular note, are fixes to the thin target's discard support,
which I hope is finally working correctly; and fixes for multipath
ioctls and device limits when there are no paths."
* tag 'dm-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm verity: fix overflow check
dm thin: fix discard support for data devices
dm thin: tidy discard support
dm: retain table limits when swapping to new table with no devices
dm table: clear add_random unless all devices have it set
dm: handle requests beyond end of device instead of using BUG_ON
dm mpath: only retry ioctl when no paths if queue_if_no_path set
dm thin: do not set discard_zeroes_data
The 'enough' function is written to work with 'near' arrays only
in that is implicitly assumes that the offset from one 'group' of
devices to the next is the same as the number of copies.
In reality it is the number of 'near' copies.
So change it to make this number explicit.
This bug makes it possible to run arrays without enough drives
present, which is dangerous.
It is appropriate for an -stable kernel, but will almost certainly
need to be modified for some of them.
Cc: stable@vger.kernel.org
Reported-by: Jakub Husák <jakub@gooseman.cz>
Signed-off-by: NeilBrown <neilb@suse.de>
This patch fixes sector_t overflow checking in dm-verity.
Without this patch, the code checks for overflow only if sector_t is
smaller than long long, not if sector_t and long long have the same size.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The discard limits that get established for a thin-pool or thin device
may be incompatible with the pool's data device. Avoid this by checking
the discard limits of the pool's data device. If an incompatibility is
found then the pool's 'discard passdown' feature is disabled.
Change thin_io_hints to ensure that a thin device always uses the same
queue limits as its pool device.
Introduce requested_pf to track whether or not the table line originally
contained the no_discard_passdown flag and use this directly for table
output. We prepare the correct setting for discard_passdown directly in
bind_control_target (called from pool_io_hints) and store it in
adjusted_pf rather than waiting until we have access to pool->pf in
pool_preresume.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
A little thin discard code refactoring to make the next patch (dm thin:
fix discard support for data devices) more readable.
Pull out a couple of functions (and uses bools instead of unsigned for
features).
No functional changes.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a safety net that will re-use the DM device's existing limits in the
event that DM device has a temporary table that doesn't have any
component devices. This is to reduce the chance that requests not
respecting the hardware limits will reach the device.
DM recalculates queue limits based only on devices which currently exist
in the table. This creates a problem in the event all devices are
temporarily removed such as all paths being lost in multipath. DM will
reset the limits to the maximum permissible, which can then assemble
requests which exceed the limits of the paths when the paths are
restored. The request will fail the blk_rq_check_limits() test when
sent to a path with lower limits, and will be retried without end by
multipath. This became a much bigger issue after v3.6 commit fe86cdcef
("block: do not artificially constrain max_sectors for stacking
drivers").
Reported-by: David Jeffery <djeffery@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Always clear QUEUE_FLAG_ADD_RANDOM if any underlying device does not
have it set. Otherwise devices with predictable characteristics may
contribute entropy.
QUEUE_FLAG_ADD_RANDOM specifies whether or not queue IO timings
contribute to the random pool.
For bio-based targets this flag is always 0 because such devices have no
real queue.
For request-based devices this flag was always set to 1 by default.
Now set it according to the flags on underlying devices. If there is at
least one device which should not contribute, set the flag to zero: If a
device, such as fast SSD storage, is not suitable for supplying entropy,
a request-based queue stacked over it will not be either.
Because the checking logic is exactly same as for the rotational flag,
share the iteration function with device_is_nonrot().
Signed-off-by: Milan Broz <mbroz@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The access beyond the end of device BUG_ON that was introduced to
dm_request_fn via commit 29e4013de7 ("dm: implement
REQ_FLUSH/FUA support for request-based dm") was an overly
drastic (but simple) response to this situation.
I have received a report that this BUG_ON was hit and now think
it would be better to use dm_kill_unmapped_request() to fail the clone
and original request with -EIO.
map_request() will assign the valid target returned by
dm_table_find_target to tio->ti. But when the target
isn't valid tio->ti is never assigned (because map_request isn't
called); so add a check for tio->ti != NULL to dm_done().
Reported-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jun'ichi Nomura <j-nomura@ce.jp.nec.com>
Cc: stable@vger.kernel.org # v2.6.37+
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When there are no paths and multipath receives an ioctl, it waits until
a path becomes available. This behaviour is incorrect if the
"queue_if_no_path" setting was not specified, as then the ioctl should
be rejected immediately, which this patch now does.
commit 35991652b ("dm mpath: allow ioctls to trigger pg init") should
have checked if queue_if_no_path was configured before queueing IO.
Checking for the queue_if_no_path feature, like is done in map_io(),
allows the following table load to work without blocking in the
multipath_ioctl retry loop:
echo "0 1024 multipath 0 0 0 0" | dmsetup create mpath_nodevs
Without this fix the multipath_ioctl will block with the following stack
trace:
blkid D 0000000000000002 0 23936 1 0x00000000
ffff8802b89e5cd8 0000000000000082 ffff8802b89e5fd8 0000000000012440
ffff8802b89e4010 0000000000012440 0000000000012440 0000000000012440
ffff8802b89e5fd8 0000000000012440 ffff88030c2aab30 ffff880325794040
Call Trace:
[<ffffffff814ce099>] schedule+0x29/0x70
[<ffffffff814cc312>] schedule_timeout+0x182/0x2e0
[<ffffffff8104dee0>] ? lock_timer_base+0x70/0x70
[<ffffffff814cc48e>] schedule_timeout_uninterruptible+0x1e/0x20
[<ffffffff8104f840>] msleep+0x20/0x30
[<ffffffffa0000839>] multipath_ioctl+0x109/0x170 [dm_multipath]
[<ffffffffa06bfb9c>] dm_blk_ioctl+0xbc/0xd0 [dm_mod]
[<ffffffff8122a408>] __blkdev_driver_ioctl+0x28/0x30
[<ffffffff8122a79e>] blkdev_ioctl+0xce/0x730
[<ffffffff811970ac>] block_ioctl+0x3c/0x40
[<ffffffff8117321c>] do_vfs_ioctl+0x8c/0x340
[<ffffffff81166293>] ? sys_newfstat+0x33/0x40
[<ffffffff81173571>] sys_ioctl+0xa1/0xb0
[<ffffffff814d70a9>] system_call_fastpath+0x16/0x1b
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org # 3.5+
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The dm thin pool target claims to support the zeroing of discarded
data areas. This turns out to be incorrect when processing discards
that do not exactly cover a complete number of blocks, so the target
must always set discard_zeroes_data_unsupported.
The thin pool target will zero blocks when they are allocated if the
skip_block_zeroing feature is not specified. The block layer
may send a discard that only partly covers a block. If a thin pool
block is partially discarded then there is no guarantee that the
discarded data will get zeroed before it is accessed again.
Due to this, thin devices cannot claim discards will always zero data.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org # 3.4+
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
commit b17459c050
raid5: add a per-stripe lock
added a spin_lock to the 'stripe_head' struct.
Unfortunately there are two places where this struct is allocated
but the spin lock was only initialised in one of them.
So add the missing spin_lock_init.
Signed-off-by: NeilBrown <neilb@suse.de>
The WRITE SAME command supported on some SCSI devices allows the same
block to be efficiently replicated throughout a block range. Only a
single logical block is transferred from the host and the storage device
writes the same data to all blocks described by the I/O.
This patch implements support for WRITE SAME in the block layer. The
blkdev_issue_write_same() function can be used by filesystems and block
drivers to replicate a buffer across a block range. This can be used to
efficiently initialize software RAID devices, etc.
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
It isn't always necessary to update the metadata when spares are
removed as the presence-or-not of a spare isn't really important to
the integrity of an array.
Also activating a spare doesn't always require updating the metadata
as the update on 'recovery-completed' is usually sufficient.
However the introduction of 'replacement' devices have made these
transitions sometimes more important. For example the 'Replacement'
flag isn't cleared until the original device is removed, so we need
to ensure a metadata update after that 'spare' is removed.
So set MD_CHANGE_DEVS whenever a spare is activated or removed, to
complement the current situation where it is set when a spare is added
or a device is failed (or a number of other less common situations).
This is suitable for -stable as out-of-data metadata could lead
to data corruption.
This is only relevant for 3.3 and later 9when 'replacement' as
introduced.
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
When a replacement device becomes active, we mark the device that it
replaces as 'faulty' so that it can subsequently get removed.
However 'calc_degraded' only pays attention to the primary device, not
the replacement, so the array appears to become degraded, which is
wrong.
So teach 'calc_degraded' to consider any replacement if a primary
device is faulty.
This is suitable for -stable as an incorrect 'degraded' value can
confuse md and could lead to data corruption.
This is only relevant for 3.3 and later.
Cc: stable@vger.kernel.org
Reported-by: Robin Hill <robin@robinhill.me.uk>
Reported-by: John Drescher <drescherjm@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
This reverts commit 895e3c5c58.
While this patch seemed like a good idea and did help some workloads,
it hurts other workloads.
Large sequential O_DIRECT writes were faster,
Small random O_DIRECT writes were slower.
Other changes (batching RAID5 writes) have improved the sequential
writes using a different mechanism, so the net result of this patch
is definitely negative. So revert it.
Reported-by: Shaohua Li <shli@kernel.org>
Tested-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Previously, there was bio_clone() but it only allocated from the fs bio
set; as a result various users were open coding it and using
__bio_clone().
This changes bio_clone() to become bio_clone_bioset(), and then we add
bio_clone() and bio_clone_kmalloc() as wrappers around it, making use of
the functionality the last patch adedd.
This will also help in a later patch changing how bio cloning works.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
CC: Alasdair Kergon <agk@redhat.com>
CC: Boaz Harrosh <bharrosh@panasas.com>
CC: Jeff Garzik <jeff@garzik.org>
Acked-by: Jeff Garzik <jgarzik@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Previously, dm_rq_clone_bio_info needed to be freed by the bio's
destructor to avoid a memory leak in the blk_rq_prep_clone() error path.
This gets rid of a memory allocation and means we can kill
dm_rq_bio_destructor.
The _rq_bio_info_cache kmem cache is unused now and needs to be deleted,
but due to the way io_pool is used and overloaded this looks not quite
trivial so I'm leaving it for a later patch.
v6: Fix comment on struct dm_rq_clone_bio_info, per Tejun
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Alasdair Kergon <agk@redhat.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Now that bios keep track of where they were allocated from,
bio_integrity_alloc_bioset() becomes redundant.
Remove bio_integrity_alloc_bioset() and drop bio_set argument from the
related functions and make them use bio->bi_pool.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Martin K. Petersen <martin.petersen@oracle.com>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
With the old code, when you allocate a bio from a bio pool you have to
implement your own destructor that knows how to find the bio pool the
bio was originally allocated from.
This adds a new field to struct bio (bi_pool) and changes
bio_alloc_bioset() to use it. This makes various bio destructors
unnecessary, so they're then deleted.
v6: Explain the temporary if statement in bio_put
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
CC: Alasdair Kergon <agk@redhat.com>
CC: Nicholas Bellinger <nab@linux-iscsi.org>
CC: Lars Ellenberg <lars.ellenberg@linbit.com>
Acked-by: Tejun Heo <tj@kernel.org>
Acked-by: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
flush[_delayed]_work_sync() are now spurious. Mark them deprecated
and convert all users to flush[_delayed]_work().
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
A 'struct r10bio' has an array of per-copy information at the end.
This array is declared with size [0] and r10bio_pool_alloc allocates
enough extra space to store the per-copy information depending on the
number of copies needed.
So declaring a 'struct r10bio on the stack isn't going to work. It
won't allocate enough space, and memory corruption will ensue.
So in the two places where this is done, declare a sufficiently large
structure and use that instead.
The two call-sites of this bug were introduced in 3.4 and 3.5
so this is suitable for both those kernels. The patch will have to
be modified for 3.4 as it only has one bug.
Cc: stable@vger.kernel.org
Reported-by: Ivan Vasilyev <ivan.vasilyev@gmail.com>
Tested-by: Ivan Vasilyev <ivan.vasilyev@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit 27a7b260f7
md: Fix handling for devices from 2TB to 4TB in 0.90 metadata.
changed 0.90 metadata handling to truncated size to 4TB as that is
all that 0.90 can record.
However for RAID0 and Linear, 0.90 doesn't need to record the size, so
this truncation is not needed and causes working arrays to become too small.
So avoid the truncation for RAID0 and Linear
This bug was introduced in 3.1 and is suitable for any stable kernels
from then onwards.
As the offending commit was tagged for 'stable', any stable kernel
that it was applied to should also get this patch. That includes
at least 2.6.32, 2.6.33 and 3.0. (Thanks to Ben Hutchings for
providing that list).
Cc: stable@vger.kernel.org
Signed-off-by: Neil Brown <neilb@suse.de>
This contains a few patches that depend on
plugging changes in the block layer so needs to wait
for those.
It also contains a Kconfig fix for the new RAID10 support
in dm-raid.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=ovN2
-----END PGP SIGNATURE-----
Merge tag 'md-3.6' of git://neil.brown.name/md
Pull additional md update from NeilBrown:
"This contains a few patches that depend on plugging changes in the
block layer so needed to wait for those.
It also contains a Kconfig fix for the new RAID10 support in dm-raid."
* tag 'md-3.6' of git://neil.brown.name/md:
md/dm-raid: DM_RAID should select MD_RAID10
md/raid1: submit IO from originating thread instead of md thread.
raid5: raid5d handle stripe in batch way
raid5: make_request use batch stripe release
Now that DM_RAID supports raid10, it needs to select that code
to ensure it is included.
Cc: Jonathan Brassow <jbrassow@redhat.com>
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
queuing writes to the md thread means that all requests go through the
one processor which may not be able to keep up with very high request
rates.
So use the plugging infrastructure to submit all requests on unplug.
If a 'schedule' is needed, we fall back on the old approach of handing
the requests to the thread for it to handle.
Signed-off-by: NeilBrown <neilb@suse.de>
Let raid5d handle stripe in batch way to reduce conf->device_lock locking.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
make_request() does stripe release for every stripe and the stripe usually has
count 1, which makes previous release_stripe() optimization not work. In my
test, this release_stripe() becomes the heaviest pleace to take
conf->device_lock after previous patches applied.
Below patch makes stripe release batch. All the stripes will be released in
unplug. The STRIPE_ON_UNPLUG_LIST bit is to protect concurrent access stripe
lru.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Pull block driver changes from Jens Axboe:
- Making the plugging support for drivers a bit more sane from Neil.
This supersedes the plugging change from Shaohua as well.
- The usual round of drbd updates.
- Using a tail add instead of a head add in the request completion for
ndb, making us find the most completed request more quickly.
- A few floppy changes, getting rid of a duplicated flag and also
running the floppy init async (since it takes forever in boot terms)
from Andi.
* 'for-3.6/drivers' of git://git.kernel.dk/linux-block:
floppy: remove duplicated flag FD_RAW_NEED_DISK
blk: pass from_schedule to non-request unplug functions.
block: stack unplug
blk: centralize non-request unplug handling.
md: remove plug_cnt feature of plugging.
block/nbd: micro-optimization in nbd request completion
drbd: announce FLUSH/FUA capability to upper layers
drbd: fix max_bio_size to be unsigned
drbd: flush drbd work queue before invalidate/invalidate remote
drbd: fix potential access after free
drbd: call local-io-error handler early
drbd: do not reset rs_pending_cnt too early
drbd: reset congestion information before reporting it in /proc/drbd
drbd: report congestion if we are waiting for some userland callback
drbd: differentiate between normal and forced detach
drbd: cleanup, remove two unused global flags
floppy: Run floppy initialization asynchronous
Pull md updates from NeilBrown.
* 'for-next' of git://neil.brown.name/md:
DM RAID: Add support for MD RAID10
md/RAID1: Add missing case for attempting to repair known bad blocks.
md/raid5: For odirect-write performance, do not set STRIPE_PREREAD_ACTIVE.
md/raid1: don't abort a resync on the first badblock.
md: remove duplicated test on ->openers when calling do_md_stop()
raid5: Add R5_ReadNoMerge flag which prevent bio from merging at block layer
md/raid1: prevent merging too large request
md/raid1: read balance chooses idlest disk for SSD
md/raid1: make sequential read detection per disk based
MD RAID10: Export md_raid10_congested
MD: Move macros from raid1*.h to raid1*.c
MD RAID1: rename mirror_info structure
MD RAID10: rename mirror_info structure
MD RAID10: Fix compiler warning.
raid5: add a per-stripe lock
raid5: remove unnecessary bitmap write optimization
raid5: lockless access raid5 overrided bi_phys_segments
raid5: reduce chance release_stripe() taking device_lock
This will allow md/raid to know why the unplug was called,
and will be able to act according - if !from_schedule it
is safe to perform tasks which could themselves schedule.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
Both md and umem has similar code for getting notified on an
blk_finish_plug event.
Centralize this code in block/ and allow each driver to
provide its distinctive difference.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
This seemed like a good idea at the time, but after further thought I
cannot see it making a difference other than very occasionally and
testing to try to exercise the case it is most likely to help did not
show any performance difference by removing it.
So remove the counting of active plugs and allow 'pending writes' to
be activated at any time, not just when no plugs are active.
This is only relevant when there is a write-intent bitmap, and the
updating of the bitmap will likely introduce enough delay that
the single-threading of bitmap updates will be enough to collect large
numbers of updates together.
Removing this will make it easier to centralise the unplug code, and
will clear the other for other unplug enhancements which have a
measurable effect.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
When doing resync or repair, attempt to correct bad blocks, according
to WriteErrorSeen policy
Signed-off-by: Alex Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Merge Andrew's first set of patches:
"Non-MM patches:
- lots of misc bits
- tree-wide have_clk() cleanups
- quite a lot of printk tweaks. I draw your attention to "printk:
convert the format for KERN_<LEVEL> to a 2 byte pattern" which
looks a bit scary. But afaict it's solid.
- backlight updates
- lib/ feature work (notably the addition and use of memweight())
- checkpatch updates
- rtc updates
- nilfs updates
- fatfs updates (partial, still waiting for acks)
- kdump, proc, fork, IPC, sysctl, taskstats, pps, etc
- new fault-injection feature work"
* Merge emailed patches from Andrew Morton <akpm@linux-foundation.org>: (128 commits)
drivers/misc/lkdtm.c: fix missing allocation failure check
lib/scatterlist: do not re-write gfp_flags in __sg_alloc_table()
fault-injection: add tool to run command with failslab or fail_page_alloc
fault-injection: add selftests for cpu and memory hotplug
powerpc: pSeries reconfig notifier error injection module
memory: memory notifier error injection module
PM: PM notifier error injection module
cpu: rewrite cpu-notifier-error-inject module
fault-injection: notifier error injection
c/r: fcntl: add F_GETOWNER_UIDS option
resource: make sure requested range is included in the root range
include/linux/aio.h: cpp->C conversions
fs: cachefiles: add support for large files in filesystem caching
pps: return PTR_ERR on error in device_create
taskstats: check nla_reserve() return
sysctl: suppress kmemleak messages
ipc: use Kconfig options for __ARCH_WANT_[COMPAT_]IPC_PARSE_VERSION
ipc: compat: use signed size_t types for msgsnd and msgrcv
ipc: allow compat IPC version field parsing if !ARCH_WANT_OLD_COMPAT_IPC
ipc: add COMPAT_SHMLBA support
...
Use memweight() to count the total number of bits set in memory area.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Alasdair Kergon <agk@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
'sync' writes set both REQ_SYNC and REQ_NOIDLE.
O_DIRECT writes set REQ_SYNC but not REQ_NOIDLE.
We currently assume that a REQ_SYNC request will not be followed by
more requests and so set STRIPE_PREREAD_ACTIVE to expedite the
request.
This is appropriate for sync requests, but not for O_DIRECT requests.
So make the setting of STRIPE_PREREAD_ACTIVE conditional on REQ_NOIDLE
rather than REQ_SYNC. This is consistent with the documented meaning
of REQ_NOIDLE:
__REQ_NOIDLE, /* don't anticipate more IO after this one */
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If a resync of a RAID1 array with 2 devices finds a known bad block
one device it will neither read from, or write to, that device for
this block offset.
So there will be one read_target (The other device) and zero write
targets.
This condition causes md/raid1 to abort the resync assuming that it
has finished - without known bad blocks this would be true.
When there are no write targets because of the presence of bad blocks
we should only skip over the area covered by the bad block.
RAID10 already gets this right, raid1 doesn't. Or didn't.
As this can cause a 'sync' to abort early and appear to have succeeded
it could lead to some data corruption, so it suitable for -stable.
Cc: stable@vger.kernel.org
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
do_md_stop tests mddev->openers while holding ->open_mutex,
and fails if this count is too high.
So callers do not need to check mddev->openers and doing so isn't
very meaningful as they don't hold ->open_mutex so the number could
change.
So remove the unnecessary tests on mddev->openers.
These are not called often enough for there to be any gain in
an early test on ->open_mutex to avoid the need for a slightly more
costly mutex_lock call.
Signed-off-by: NeilBrown <neilb@suse.de>
Because bios will merge at block-layer,so bios-error may caused by other
bio which be merged into to the same request.
Using this flag,it will find exactly error-sector and not do redundant
operation like re-write and re-read.
V0->V1:Using REQ_FLUSH instead REQ_NOMERGE avoid bio merging at block
layer.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
For SSD, if request size exceeds specific value (optimal io size), request size
isn't important for bandwidth. In such condition, if making request size bigger
will cause some disks idle, the total throughput will actually drop. A good
example is doing a readahead in a two-disk raid1 setup.
So when should we split big requests? We absolutly don't want to split big
request to very small requests. Even in SSD, big request transfer is more
efficient. This patch only considers request with size above optimal io size.
If all disks are busy, is it worth doing a split? Say optimal io size is 16k,
two requests 32k and two disks. We can let each disk run one 32k request, or
split the requests to 4 16k requests and each disk runs two. It's hard to say
which case is better, depending on hardware.
So only consider case where there are idle disks. For readahead, split is
always better in this case. And in my test, below patch can improve > 30%
thoughput. Hmm, not 100%, because disk isn't 100% busy.
Such case can happen not just in readahead, for example, in directio. But I
suppose directio usually will have bigger IO depth and make all disks busy, so
I ignored it.
Note: if the raid uses any hard disk, we don't prevent merging. That will make
performace worse.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
SSD hasn't spindle, distance between requests means nothing. And the original
distance based algorithm sometimes can cause severe performance issue for SSD
raid.
Considering two thread groups, one accesses file A, the other access file B.
The first group will access one disk and the second will access the other disk,
because requests are near from one group and far between groups. In this case,
read balance might keep one disk very busy but the other relative idle. For
SSD, we should try best to distribute requests to as many disks as possible.
There isn't spindle move penality anyway.
With below patch, I can see more than 50% throughput improvement sometimes
depending on workloads.
The only exception is small requests can be merged to a big request which
typically can drive higher throughput for SSD too. Such small requests are
sequential reads. Unlike hard disk, sequential read which can't be merged (for
example direct IO, or read without readahead) can be ignored for SSD. Again
there is no spindle move penality. readahead dispatches small requests and such
requests can be merged.
Last patch can help detect sequential read well, at least if concurrent read
number isn't greater than raid disk number. In that case, distance based
algorithm doesn't work well too.
V2: For hard disk and SSD mixed raid, doesn't use distance based algorithm for
random IO too. This makes the algorithm generic for raid with SSD.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Currently the sequential read detection is global wide. It's natural to make it
per disk based, which can improve the detection for concurrent multiple
sequential reads. And next patch will make SSD read balance not use distance
based algorithm, where this change help detect truly sequential read for SSD.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
md/raid10: Export is_congested test.
In similar fashion to commits
11d8a6e3711ed7242e59
we export the RAID10 congestion checking function so that dm-raid.c can
make use of it and make use of the personality. The 'queue' and 'gendisk'
structures will not be available to the MD code when device-mapper sets
up the device, so we conditionalize access to these fields also.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
MD RAID1/RAID10: Move some macros from .h file to .c file
There are three macros (IO_BLOCKED,IO_MADE_GOOD,BIO_SPECIAL) which are defined
in both raid1.h and raid10.h. They are only used in there respective .c files.
However, if we wish to make RAID10 accessible to the device-mapper RAID
target (dm-raid.c), then we need to move these macros into the .c files where
they are used so that they do not conflict with each other.
The macros from the two files are identical and could be moved into md.h, but
I chose to leave the duplication and have them remain in the personality
files.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
MD RAID1: Rename the structure 'mirror_info' to 'raid1_info'
The same structure name ('mirror_info') is used by raid10. Each of these
structures are defined in there respective header files. If dm-raid is
to support both RAID1 and RAID10, the header files will be included and
the structure names must not collide. While only one of these structure
names needs to change, this patch adds consistency to the naming of the
structure.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
MD RAID10: Rename the structure 'mirror_info' to 'raid10_info'
The same structure name ('mirror_info') is used by raid1. Each of these
structures are defined in there respective header files. If dm-raid is
to support both RAID1 and RAID10, the header files will be included and
the structure names must not collide.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Commit outstanding metadata before returning the status for a dm thin
pool so that the numbers reported are as up-to-date as possible.
The commit is not performed if the device is suspended or if
the DM_NOFLUSH_FLAG is supplied by userspace and passed to the target
through a new 'status_flags' parameter in the target's dm_status_fn.
The userspace dmsetup tool will support the --noflush flag with the
'dmsetup status' and 'dmsetup wait' commands from version 1.02.76
onwards.
Tested-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add read-only and fail-io modes to thin provisioning.
If a transaction commit fails the pool's metadata device will transition
to "read-only" mode. If a commit fails once already in read-only mode
the transition to "fail-io" mode occurs.
Once in fail-io mode the pool and all associated thin devices will
report a status of "Fail".
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce dm_pool_abort_metadata to abort the current metadata
transaction. Generally this will only be called when bad things are
happening and dm-thin is trying to roll back to a good state for
read-only mode.
It's complicated by the fact that the metadata device may have failed
completely causing the abort to be unable to read the old transaction.
In this case the metadata object is placed in a 'fail' mode and
everything fails apart from destroying it.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce dm_pool_metadata_set_read_only to put the underlying block
manager into read-only mode.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce dm_bm_set_read_only to switch the block manager into a
read-only mode. To be used when dm-thin degrades due to io errors on
the metadata device.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reduce the number of metadata commits by using
dm_thin_changed_this_transaction to check if metadata was changed on a
per thin device granularity.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce dm_thin_changed_this_transaction to dm-thin-metadata to publish a
useful bit of information we're already tracking. This will help dm thin
decide when to commit.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a parameter to dm_pool_metadata_open to indicate whether or not an
unformatted metadata area should be formatted.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Tidy up error path in __open_metadata and __format_metadata in dm-thin-metadata.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Factor out __check_incompat_features and only call it once when we open
the metadata device rather than at the beginning of every transaction.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove some duplicate initialisation of struct dm_pool_metadata.
These pmd fields are initialised by both:
__format_metadata's calls to dm_btree_empty
__write_initial_superblock + __begin_transaction
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove 'create' parameter from __create_persistent_data_objects() in dm-thin-metadata.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move the check for __superblock_all_zeroes from
__create_persistent_data_objects() down to __open_or_format_metadata in
dm-thin-metadata.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove nr_blocks arg from __create_persistent_data_objects in dm-thin-metadata.
It was always passed as zero.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Split __open_or_format_metadata into __format_metadata and __open_metadata in
dm-thin-metadata.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Clean up __open_or_format_metadata in dm-thin-metadata by using struct
dm_pool_metadata members to replace local variables.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Zero the unused uuid when initialising the metadata superblock.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Lift the call to __begin_transaction out of __write_initial_superblock in
dm-thin-metadata. Called higher up the call chain now.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move dm_commit_pool_metadata inline into __write_initial_superblock in dm-thin-metadata.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Factor out __write_initial_superblock and also pull some other initial
creation code out of dm_pool_metadata_open.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Lift some initialisation out of __open_or_format_metadata in dm-thin-metadata.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Factor __destroy_persistent_data_objects out of dm_pool_metadata_close.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move block manager creation and the check for unformatted metadata into
__create_persistent_data_objects().
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rename init_pmd to __create_persistent_data_objects in dm-thin-metadata.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce wrappers to handle write locking the superblock
appropriately.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Stop using dm_bm_unlock_move when shadowing blocks in the transaction
manager as an optimisation and remove the function as it is then no
longer used.
Some code, such as the space maps, keeps using on-disk data structures
from the previous transaction. It can do this because blocks won't
be reallocated until the subsequent transaction. Using
dm_bm_unlock_move to copy blocks sounds like a win, but it forces a
synchronous read should the old block be accessed.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Tidy the transaction manager creation functions.
They no longer lock the superblock. Superblock locking is pulled out to
the caller.
Also export dm_bm_write_lock_zero.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove an optimisation that tracks whether or not a thin metadata commit
is needed.
If dm_pool_commit_metadata() is called and no changes have been made
to the metadata then this optimisation avoided writing to disk.
Removing because we're going to do something better later.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch introduces a separate struct for the block_manager.
It also uses IS_ERR to check the return value of dm_bufio_client_create
instead of testing incorrectly for NULL.
Prior to this patch a struct dm_block_manager was really an alias for
a struct dm_bufio_client. We want to add some functionality to the
block manager that will require extra fields, so this one to one
mapping is no longer valid.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Factor __setup_btree_details out of init_pmd in dm-thin-metadata.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The thin provisioning target commits internal metadata on flush. So it
should receive flushes regardless of whether the underlying devices
support them.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Allow targets to override the 'supports flush' calculation.
Set 'flush_supported' if a target needs to receive flushes regardless of
whether or not its underlying devices have support.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce bitmap_index_changed to track whether or not the index changed
then only commit a space map if it did.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Unlock the superblock even if initial dm_bufio_write_dirty_buffers fails.
Also, remove redundant flush calls. dm_bm_flush_and_unlock's calls to
dm_bufio_write_dirty_buffers already result in dm_bufio_issue_flush
being called.
This avoids warnings about unflushed dirty buffers from bufio.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
There's no need to break sharing, triggering a copy, for a write that has no
data (i.e. a flush).
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Fix memory leak in process_prepared_mapping by always freeing
the dm_thin_new_mapping structs from the mapping_pool mempool on
the error paths.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Rename sector to cc_sector in dm-crypt's convert_context struct.
This is preparation for a future patch that merges dm_io and
convert_context which both have a "sector" field.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Store the crypt_config struct pointer directly in struct dm_crypt_io
instead of the dm_target struct pointer.
Target information is never used - only target->private is referenced,
thus we can change it to point directly to struct crypt_config.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move static dm-crypt cipher data out of per-cpu structure.
Cipher information is static, so it does not have to be in a per-cpu
structure.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
In preparation for RAID10 inclusion in dm-raid, we move the sectors_per_dev
calculation later in the device creation process. This is because we won't
know up-front how many stripes vs how many mirrors there are which will
change the calculation.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
There are two dm crypt structures that have a field called "pending".
This patch renames them to "cc_pending" and "io_pending" to reduce confusion
and ease searching the code.
Also remove unnecessary initialisation of r in crypt_convert_block().
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
In preparation for RAID10 addition to dm-raid, we change an 'if' conditional
to a 'switch' conditional to make it easier to see what is being checked for
each RAID type.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
A SCSI device handler might get attached to a device during the
initial device scan. We do not necessarily want to override
this when loading a multipath table, so this patch adds a new
multipath feature argument "retain_attached_hw_handler".
During SCSI device scan all loaded SCSI device handlers will be
consulted for a match (via scsi_dh's provided .match). If a match is
found that device handler will be attached. We need a way to have
userspace multipathd's provided 'hw_handler' not override the already
attached hardware handler.
When specifying the new feature 'retain_attached_hw_handler' multipath
will use the currently attached hardware handler instead of trying to
attach the one specified during table load. If no hardware handler is
attached the specified hardware handler will still be used.
Leverages scsi_dh_attach's ability to increment the scsi_dh's reference
count if the same scsi_dh name is provided when attaching - currently
attached scsi_dh name is determined with scsi_dh_attached_handler_name.
Depends upon commit 7e8a74b177
("[SCSI] scsi_dh: add scsi_dh_attached_handler_name").
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Tested-by: Babu Moger <babu.moger@netapp.com>
Reviewed-by: Chandra Seetharaman <sekharan@us.ibm.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm-thin will be most likely used with a block size that is a power of
two. So it should be optimized for this case.
This patch changes division and modulo operations to shifts and bit
masks if block size is a power of two.
A test that bi_sector is divisible by a block size is removed from
io_overlaps_block. Device mapper never sends bios that span a block
boundary. Consequently, if we tested that bi_size is equivalent to block
size, bi_sector must already be on a block boundary.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch sets the variable "ti->split_discard_requests" for the dm thin
target so that device mapper core splits discard requests on a block
boundary.
Consequently, a discard request that spans multiple blocks is never sent
to dm-thin. The patch also removes some code in process_discard that
deals with discards that span multiple blocks.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch introduces a new variable split_discard_requests. It can be
set by targets so that discard requests are split on max_io_len
boundaries.
When split_discard_requests is not set, discard requests are only split on
boundaries between targets, as was the case before this patch.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Non power of 2 blocksize support is needed to properly align thinp IO
on storage that has non power of 2 optimal IO sizes (e.g. RAID6 10+2).
Use sector_div to support non power of 2 blocksize for the pool's
data device. This provides comparable performance to the power of 2
math that was performed until now (as tested on modern x86_64 hardware).
The kernel currently assumes that limits->discard_granularity is a power
of two so the thin target only enables discard support if the block
size is a power of two.
Eliminate pool structure's 'block_shift', 'offset_mask' and
remaining 4 byte holes.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm-stripe is usually used with a chunk size that is a power of two.
Use faster shifts and bit masks in such cases.
stripe_width is already optimized in a similar way.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
There is no technical limitation in device mapper that would prevent the
dm-stripe target from using a stripe size smaller than page size.
This patch removes the limit and makes stripe volumes portable across
architectures with different page size.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Support non-power-of-2 chunk sizes with dm striping for proper alignment
of stripe IO on storage that has non-power-of-2 optimal IO sizes (e.g.
RAID6 10+2).
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove the restriction that limits a target's specified maximum incoming
I/O size to be a power of 2.
Rename this setting from 'split_io' to the less-ambiguous 'max_io_len'.
Change it from sector_t to uint32_t, which is plenty big enough, and
introduce a wrapper function dm_set_target_max_io_len() to set it.
Use sector_div() to process it now that it is not necessarily a power of 2.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The structure stripe_c contains a stripes_mask field. This field is
useless because it can be trivially calculated by subtracting one from
stripes. It is used only at one place. This patch removes it.
The patch also changes ffs(stripes) - 1 to __ffs(stripes).
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
dm-stripe is supposed to ensure that all the space allocated to the
stripes is fully used and that all stripes are the same size. This
patch fixes the test. It checks that device length is divisible by the
chunk size and checks that the resulting quotient is divisible by the
number of stripes (which is equivalent to testing if device length is
divisible by chunk_size * stripes).
Previously, the code only tested that the number of sectors in the target
was divisible by each of the chunk size and the number of stripes
separately, which could leave entire stripes unused.
(A setup that genuinely needs some stripes to be shorter than others
can be created by concatenating striped targets.)
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Provide specific error message strings for two pool_ctr() failure cases
that currently give just "Unknown error".
Reference: test_two_pools_pointing_to_the_same_metadata_fails and
test_different_pool_cant_replace_pool in thinp-test-suite.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Introduce THIN_MAX_CONCURRENT_LOCKS into dm-thin-metadata to
give a name to an otherwise "magic" number.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove the pointless label 'out' from __commit_transaction in
dm-thin-metadata.c
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Remove debug space map checker from dm persistent data.
The space map checker is a wrapper for other space maps that double
checks the reference counts are correct. It holds all these reference
counts in memory rather than on disk, so uses a lot of memory and is
thus restricted to small pools.
As yet, this checker hasn't found any issues, but has caused a few of
its own due to people turning it on by default with larger pools.
Removing.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Clean up "warning: dubious: !x & y". Also make it clear that
__snapshotted_since() returns a bool and that dm_thin_lookup_result's
'shared' member is a flag.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reduce the slab size used for the dm_thin_endio_hook mempool.
Allocation has been seen to fail on machines with smaller amounts
of memory due to fragmentation.
lvm: page allocation failure. order:5, mode:0xd0
device-mapper: table: 253:38: thin-pool: Error creating pool's endio_hook mempool
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
- avoid a crash in dm-raid1 when discards coincide with mirror recovery;
- avoid discarding shared data that's still needed in dm-thin;
- don't guarantee that discarded blocks will be wiped in dm-raid1.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=gbLp
-----END PGP SIGNATURE-----
Merge tag 'dm-3.5-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper discard fixes from Alasdair G Kergon:
- avoid a crash in dm-raid1 when discards coincide with mirror
recovery;
- avoid discarding shared data that's still needed in dm-thin;
- don't guarantee that discarded blocks will be wiped in dm-raid1.
* tag 'dm-3.5-fixes-2' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm raid1: set discard_zeroes_data_unsupported
dm thin: do not send discards to shared blocks
dm raid1: fix crash with mirror recovery and discard
We can't guarantee that REQ_DISCARD on dm-mirror zeroes the data even if
the underlying disks support zero on discard. So this patch sets
ti->discard_zeroes_data_unsupported.
For example, if the mirror is in the process of resynchronizing, it may
happen that kcopyd reads a piece of data, then discard is sent on the
same area and then kcopyd writes the piece of data to another leg.
Consequently, the data is not zeroed.
The flag was made available by commit 983c7db347
(dm crypt: always disable discard_zeroes_data).
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
When process_discard receives a partial discard that doesn't cover a
full block, it sends this discard down to that block. Unfortunately, the
block can be shared and the discard would corrupt the other snapshots
sharing this block.
This patch detects block sharing and ends the discard with success when
sending it to the shared block.
The above change means that if the device supports discard it can't be
guaranteed that a discard request zeroes data. Therefore, we set
ti->discard_zeroes_data_unsupported.
Thin target discard support with this bug arrived in commit
104655fd4d (dm thin: support discards).
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
This patch fixes a crash when a discard request is sent during mirror
recovery.
Firstly, some background. Generally, the following sequence happens during
mirror synchronization:
- function do_recovery is called
- do_recovery calls dm_rh_recovery_prepare
- dm_rh_recovery_prepare uses a semaphore to limit the number
simultaneously recovered regions (by default the semaphore value is 1,
so only one region at a time is recovered)
- dm_rh_recovery_prepare calls __rh_recovery_prepare,
__rh_recovery_prepare asks the log driver for the next region to
recover. Then, it sets the region state to DM_RH_RECOVERING. If there
are no pending I/Os on this region, the region is added to
quiesced_regions list. If there are pending I/Os, the region is not
added to any list. It is added to the quiesced_regions list later (by
dm_rh_dec function) when all I/Os finish.
- when the region is on quiesced_regions list, there are no I/Os in
flight on this region. The region is popped from the list in
dm_rh_recovery_start function. Then, a kcopyd job is started in the
recover function.
- when the kcopyd job finishes, recovery_complete is called. It calls
dm_rh_recovery_end. dm_rh_recovery_end adds the region to
recovered_regions or failed_recovered_regions list (depending on
whether the copy operation was successful or not).
The above mechanism assumes that if the region is in DM_RH_RECOVERING
state, no new I/Os are started on this region. When I/O is started,
dm_rh_inc_pending is called, which increases reg->pending count. When
I/O is finished, dm_rh_dec is called. It decreases reg->pending count.
If the count is zero and the region was in DM_RH_RECOVERING state,
dm_rh_dec adds it to the quiesced_regions list.
Consequently, if we call dm_rh_inc_pending/dm_rh_dec while the region is
in DM_RH_RECOVERING state, it could be added to quiesced_regions list
multiple times or it could be added to this list when kcopyd is copying
data (it is assumed that the region is not on any list while kcopyd does
its jobs). This results in memory corruption and crash.
There already exist bypasses for REQ_FLUSH requests: REQ_FLUSH requests
do not belong to any region, so they are always added to the sync list
in do_writes. dm_rh_inc_pending does not increase count for REQ_FLUSH
requests. In mirror_end_io, dm_rh_dec is never called for REQ_FLUSH
requests. These bypasses avoid the crash possibility described above.
These bypasses were improperly implemented for REQ_DISCARD when
the mirror target gained discard support in commit
5fc2ffeabb (dm raid1: support discard).
In do_writes, REQ_DISCARD requests is always added to the sync queue and
immediately dispatched (even if the region is in DM_RH_RECOVERING). However,
dm_rh_inc and dm_rh_dec is called for REQ_DISCARD resusts. So it violates the
rule that no I/Os are started on DM_RH_RECOVERING regions, and causes the list
corruption described above.
This patch changes it so that REQ_DISCARD requests follow the same path
as REQ_FLUSH. This avoids the crash.
Reference: https://bugzilla.redhat.com/837607
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Add a per-stripe lock to protect stripe specific data. The purpose is to reduce
lock contention of conf->device_lock.
stripe ->toread, ->towrite are protected by per-stripe lock. Accessing bio
list of the stripe is always serialized by this lock, so adding bio to the
lists (add_stripe_bio()) and removing bio from the lists (like
ops_run_biofill()) not race.
If bio in ->read, ->written ... list are not shared by multiple stripes, we
don't need any lock to protect ->read, ->written, because STRIPE_ACTIVE will
protect them. If the bio are shared, there are two protections:
1. bi_phys_segments acts as a reference count
2. traverse the list uses r5_next_bio, which makes traverse never access bio
not belonging to the stripe
Let's have an example:
| stripe1 | stripe2 | stripe3 |
...bio1......|bio2|bio3|....bio4.....
stripe2 has 4 bios, when it's finished, it will decrement bi_phys_segments for
all bios, but only end_bio for bio2 and bio3. bio1->bi_next still points to
bio2, but this doesn't matter. When stripe1 is finished, it will not touch bio2
because of r5_next_bio check. Next time stripe1 will end_bio for bio1 and
stripe3 will end_bio bio4.
before add_stripe_bio() addes a bio to a stripe, we already increament the bio
bi_phys_segments, so don't worry other stripes release the bio.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Neil pointed out the bitmap write optimization in handle_stripe_clean_event()
is unnecessary, because the chance one stripe gets written twice in the mean
time is rare. We can always do a bitmap_startwrite when a write request is
added to a stripe and bitmap_endwrite after write request is done. Delete the
optimization. With it, we can delete some cases of device_lock.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Raid5 overrides bio->bi_phys_segments, accessing it is with device_lock hold,
which is unnecessary, We can make it lockless actually.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
release_stripe() is a place conf->device_lock is heavily contended. We take the
lock even stripe count isn't 1, which isn't required.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit 4367af5561
md/raid1: clear bad-block record when write succeeds.
Added a 'reschedule_retry' call possibility at the end of
end_sync_write, but didn't add matching code at the end of
sync_request_write. So if the writes complete very quickly, or
scheduling makes it seem that way, then we can miss rescheduling
the request and the resync could hang.
Also commit 73d5c38a95
md: avoid races when stopping resync.
Fix a race condition in this same code in end_sync_write but didn't
make the change in sync_request_write.
This patch updates sync_request_write to fix both of those.
Patch is suitable for 3.1 and later kernels.
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Original-version-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
md will refuse to stop an array if any other fd (or mounted fs) is
using it.
When any fs is unmounted of when the last open fd is closed all
pending IO will be flushed (e.g. sync_blockdev call in __blkdev_put)
so there will be no pending IO to worry about when the array is
stopped.
However in order to send the STOP_ARRAY ioctl to stop the array one
must first get and open fd on the block device.
If some fd is being used to write to the block device and it is closed
after mdadm open the block device, but before mdadm issues the
STOP_ARRAY ioctl, then there will be no last-close on the md device so
__blkdev_put will not call sync_blockdev.
If this happens, then IO can still be in-flight while md tears down
the array and bad things can happen (use-after-free and subsequent
havoc).
So in the case where do_md_stop is being called from an open file
descriptor, call sync_block after taking the mutex to ensure there
will be no new openers.
This is needed when setting a read-write device to read-only too.
Cc: stable@vger.kernel.org
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit c6563a8c38
md: add possibility to change data-offset for devices.
introduced a 'new_data_offset' attribute which should normally
be the same as 'data_offset', but can be explicitly set to a different
value to allow a reshape operation to move the data.
Unfortunately when the 'data_offset' is explicitly set through
sysfs, the new_data_offset is not also set, so the two would become
out-of-sync incorrectly.
One result of this is that trying to set the 'size' after the
'data_offset' would fail because it is not permitted to set the size
when the 'data_offset' and 'new_data_offset' are different - as that
can be confusing.
Consequently when mdadm tried to do this while assembling an IMSM
array it would fail.
This bug was introduced in 3.5-rc1.
Reported-by: Brian Downing <bdowning@lavos.net>
Bisected-by: Brian Downing <bdowning@lavos.net>
Tested-by: Brian Downing <bdowning@lavos.net>
Signed-off-by: NeilBrown <neilb@suse.de>
This bug has been present ever since data-check was introduce
in 2.6.16. However it would only fire if a data-check were
done on a degraded array, which was only possible if the array
has 3 or more devices. This is certainly possible, but is quite
uncommon.
Since hot-replace was added in 3.3 it can happen more often as
the same condition can arise if not all possible replacements are
present.
The problem is that as soon as we submit the last read request, the
'r1_bio' structure could be freed at any time, so we really should
stop looking at it. If the last device is being read from we will
stop looking at it. However if the last device is not due to be read
from, we will still check the bio pointer in the r1_bio, but the
r1_bio might already be free.
So use the read_targets counter to make sure we stop looking for bios
to submit as soon as we have submitted them all.
This fix is suitable for any -stable kernel since 2.6.16.
Cc: stable@vger.kernel.org
Reported-by: Arnold Schulz <arnysch@gmx.net>
Signed-off-by: NeilBrown <neilb@suse.de>
I really shouldn't do important things late in the day. It seems
that I get careless.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=pDob
-----END PGP SIGNATURE-----
Merge tag 'md-3.5-fixes' of git://neil.brown.name/md
Pull raid10 build failure fix from NeilBrown:
"I really shouldn't do important things late in the day. It seems that
I get careless."
* tag 'md-3.5-fixes' of git://neil.brown.name/md:
md/raid10: fix careless build error
build error introduced by commit b357f04a67
That function doesn't get extra args until a later patch. Bother.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Reported-by: Simon Kirby <sim@hostway.ca>
Reported-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Signed-off-by: NeilBrown <neilb@suse.de>
If CONFIG_DM_DEBUG_SPACE_MAPS is enabled and memory is fragmented and a
sufficiently-large metadata device is used in a thin pool then the space
map checker will fail to allocate the memory it requires.
Switch from kmalloc to vmalloc to allow larger virtually contiguous
allocations for the space map checker's internal count arrays.
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If CONFIG_DM_DEBUG_SPACE_MAPS is enabled and dm_sm_checker_create()
fails, dm_tm_create_internal() would still return success even though it
cleaned up all resources it was supposed to have created. This will
lead to a kernel crash:
general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC
...
RIP: 0010:[<ffffffff81593659>] [<ffffffff81593659>] dm_bufio_get_block_size+0x9/0x20
Call Trace:
[<ffffffff81599bae>] dm_bm_block_size+0xe/0x10
[<ffffffff8159b8b8>] sm_ll_init+0x78/0xd0
[<ffffffff8159c1a6>] sm_ll_new_disk+0x16/0xa0
[<ffffffff8159c98e>] dm_sm_disk_create+0xfe/0x160
[<ffffffff815abf6e>] dm_pool_metadata_open+0x16e/0x6a0
[<ffffffff815aa010>] pool_ctr+0x3f0/0x900
[<ffffffff8158d565>] dm_table_add_target+0x195/0x450
[<ffffffff815904c4>] table_load+0xe4/0x330
[<ffffffff815917ea>] ctl_ioctl+0x15a/0x2c0
[<ffffffff81591963>] dm_ctl_ioctl+0x13/0x20
[<ffffffff8116a4f8>] do_vfs_ioctl+0x98/0x560
[<ffffffff8116aa51>] sys_ioctl+0x91/0xa0
[<ffffffff81869f52>] system_call_fastpath+0x16/0x1b
Fix the space map checker code to return an appropriate ERR_PTR and have
dm_sm_disk_create() and dm_tm_create_internal() check for it with
IS_ERR.
Reported-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Cleanup the shadow table before destroying the transaction manager.
Reference: leak was identified with kmemleak when running
test_discard_random_sectors in the thinp-test-suite.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Userland sometimes sees a corrupt metadata block if metadata is changing
rapidly when a metadata snapshot is reserved for userland, To make the
problem go away, commit before we take the metadata snapshot (which is a
sensible thing to do anyway).
The checksums mean userland spots this corruption immediately so there's
no risk of acting on incorrect data. No corruption exists from the
kernel's point of view, and thin_check passes after pool shutdown.
I believe this is to do with shared blocks at the first level of the
{device, mapping} btree. Prior to the metadata-snap support no sharing
at this level was possible, so this patch is only required after commit
cc8394d86f ("dm thin: provide userspace
access to pool metadata").
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The value returned by "mddev_check_plug" is only valid until the
next 'schedule' as that will unplug things. This could happen at any
call to mempool_alloc.
So just calling mddev_check_plug at the start doesn't really make
sense.
So call it just before, or just after, queuing things for the thread.
As the action that happens at unplug is to wake the thread, this makes
lots of sense.
If we cannot add a plug (which requires a small GFP_ATOMIC alloc) we
wake thread immediately.
RAID5 is a bit different. Requests are queued for the thread and the
thread is woken by release_stripe. So we don't need to wake the
thread on failure.
However the thread doesn't perform certain actions when there is any
active plug, so it is important to install a plug before waking the
thread. So for RAID5 we install the plug *before* queuing the request
and waking the thread.
Without this patch it is possible for raid1 or raid10 to queue a
request without then waking the thread, resulting in the array locking
up.
Also change raid10 to only flush_pending_write when there are not
active plugs, just like raid1.
This patch is suitable for 3.0 or later. I plan to submit it to
-stable, but I'll like to let it spend a few weeks in mainline
first to be sure it is completely safe.
Signed-off-by: NeilBrown <neilb@suse.de>
We currently only allow a device to be re-added if it appear to be
in-sync. This is overly restrictive as it may be desirable to re-add
a device that is in the middle of recovery.
So remove the test for "InSync" - the test on rdev->raid_disk is
sufficient to ensure that the re-add will succeed.
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Tested-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
When we added hot_replace we doubled the number of devices
that could be in a RAID1 array. So we doubled how far read_balance
would search. Unfortunately we didn't double the point at which
it looped back to the beginning - so it effectively loops over
all non-replacement disks twice.
This doesn't cause bad behaviour, but it pointless and means we
never read from replacement devices.
Signed-off-by: NeilBrown <neilb@suse.de>
There isn't locking setting STRIPE_DELAYED and STRIPE_PREREAD_ACTIVE bits, but
the two bits have relationship. A delayed stripe can be moved to hold list only
when preread active stripe count is below IO_THRESHOLD. If a stripe has both
the bits set, such stripe will be in delayed list and preread count not 0,
which will make such stripe never leave delayed list.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
We may not be able to fix a bad block if:
- the array is degraded
- the over-write fails.
In these cases we currently eject the device, but we should
record a bad block if possible.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Having the 'name' arg optional and defaulting to the current
personality name is no necessary and leads to errors, as when
changing the level of an array we can end up using the
name of the old level instead of the new one.
So make it non-optional and always explicitly pass the name
of the level that the array will be.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit 58c54fcca3
md/raid10: handle further errors during fix_read_error better.
in 3.1 added "r10_sync_page_io" which takes an IO size in sectors.
But we were passing the IO size in bytes!!!
This resulting in bio_add_page failing, and empty request being sent
down, and a consequent BUG_ON in scsi_lib.
[fix missing space in error message at same time]
This fix is suitable for 3.1.y and later.
Cc: stable@vger.kernel.org
Reported-by: Christian Balzer <chibi@gol.com>
Signed-off-by: NeilBrown <neilb@suse.de>
commit 43220aa0f2
md/raid5: fix a hang on device failure.
fixed a hang, but introduced a refcounting in-balance so
that if the presence of bad-blocks ever caused an rdev to
be 'blocked' we would increment the refcount on the rdev and
never decrement it.
So added the needed rdev_dec_pending when md_wait_for_blocked_rdev
is not called.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In ops_run_io(), the call to md_wait_for_blocked_rdev will decrement
nr_pending so we lose the reference we hold on the rdev.
So atomic_inc it first to maintain the reference.
This bug was introduced by commit 73e92e51b7
md/raid5. Don't write to known bad block on doubtful devices.
which appeared in 3.0, so patch is suitable for stable kernels since
then.
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
In chunk_aligned_read() we are adding data_offset before calling
is_badblock. But is_badblock also adds data_offset, so that is bad.
So move the addition of data_offset to after the call to
is_badblock.
This bug was introduced by commit 31c176ecdf
md/raid5: avoid reading from known bad blocks.
which first appeared in 3.0. So that patch is suitable for any
-stable kernel from 3.0.y onwards. However it will need minor
revision for most of those (as the comment didn't appear until
recently).
Cc: stable@vger.kernel.org
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If a RAID5 has both a failed device and a device marked as
'WantReplacement', then we should preferentially replace the failed
device.
However the current code replaces whichever is found first.
So split into 2 loops, check fail failed/missing first, and only check
for WantReplacement if nothing is failed or missing.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
If a RAID10 has an odd number of chunks - as might happen when there
are an odd number of devices - the last chunk has no pair and so is
not mirrored. We don't store data there, but when recovering the last
device in an array we retry to recover that last chunk from a
non-existent location. This results in an error, and the recovery
aborts.
When we get to that last chunk we should just stop - there is nothing
more to do anyway.
This bug has been present since the introduction of RAID10, so the
patch is appropriate for any -stable kernel.
Cc: stable@vger.kernel.org
Reported-by: Christian Balzer <chibi@gol.com>
Tested-by: Christian Balzer <chibi@gol.com>
Signed-off-by: NeilBrown <neilb@suse.de>
One sparse-warning fix, one bigfix for 3.4-stable
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=VrYL
-----END PGP SIGNATURE-----
Merge tag 'md-3.5-fixes' of git://neil.brown.name/md
Pull two md fixes from NeilBrown:
"One sparse-warning fix, one bugfix for 3.4-stable"
* tag 'md-3.5-fixes' of git://neil.brown.name/md:
md: raid1/raid10: fix problem with merge_bvec_fn
lib/raid6: fix sparse warnings in recovery functions
and provide a simple reserve/release mechanism for userspace tools to
access thin provisioning metadata while the pool is in use.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=wCpY
-----END PGP SIGNATURE-----
Merge tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm
Pull device-mapper updates from Alasdair G Kergon:
"Improve multipath's retrying mechanism in some defined circumstances
and provide a simple reserve/release mechanism for userspace tools to
access thin provisioning metadata while the pool is in use."
* tag 'dm-3.5-changes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/agk/linux-dm:
dm thin: provide userspace access to pool metadata
dm thin: use slab mempools
dm mpath: allow ioctls to trigger pg init
dm mpath: delay retry of bypassed pg
dm mpath: reduce size of struct multipath
This patch implements two new messages that can be sent to the thin
pool target allowing it to take a snapshot of the _metadata_. This,
read-only snapshot can be accessed by userland, concurrently with the
live target.
Only one metadata snapshot can be held at a time. The pool's status
line will give the block location for the current msnap.
Since version 0.1.5 of the userland thin provisioning tools, the
thin_dump program displays the msnap as follows:
thin_dump -m <msnap root> <metadata dev>
Available here: https://github.com/jthornber/thin-provisioning-tools
Now that userland can access the metadata we can do various things
that have traditionally been kernel side tasks:
i) Incremental backups.
By using metadata snapshots we can work out what blocks have
changed over time. Combined with data snapshots we can ensure
the data doesn't change while we back it up.
A short proof of concept script can be found here:
https://github.com/jthornber/thinp-test-suite/blob/master/incremental_backup_example.rb
ii) Migration of thin devices from one pool to another.
iii) Merging snapshots back into an external origin.
iv) Asyncronous replication.
Signed-off-by: Joe Thornber <ejt@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Use dedicated caches prefixed with a "dm_" name rather than relying on
kmalloc mempools backed by generic slab caches so the memory usage of
thin provisioning (and any leaks) can be accounted for independently.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
After the failure of a group of paths, any alternative paths that
need initialising do not become available until further I/O is sent to
the device. Until this has happened, ioctls return -EAGAIN.
With this patch, new paths are made available in response to an ioctl
too. The processing of the ioctl gets delayed until this has happened.
Instead of returning an error, we submit a work item to kmultipathd
(that will potentially activate the new path) and retry in ten
milliseconds.
Note that the patch doesn't retry an ioctl if the ioctl itself fails due
to a path failure. Such retries should be handled intelligently by the
code that generated the ioctl in the first place, noting that some SCSI
commands should not be retried because they are not idempotent (XOR write
commands). For commands that could be retried, there is a danger that
if the device rejected the SCSI command, the path could be errorneously
marked as failed, and the request would be retried on another path which
might fail too. It can be determined if the failure happens on the
device or on the SCSI controller, but there is no guarantee that all
SCSI drivers set these flags correctly.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
If I/O needs retrying and only bypassed priority groups are available,
set the pg_init_delay_retry flag to wait before retrying.
If, for example, the reason for the bypass is that the controller is
getting reset or there is a firmware upgrade happening, retrying right
away would cause a flood of log messages and retries for what could be a
few seconds or even several minutes.
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Move multipath structure's 'lock' and 'queue_size' members to eliminate
two 4-byte holes. Also use a bit within a single unsigned int for each
existing flag (saves 8-bytes). This allows future flags to be added
without each consuming an unsigned int.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
The new merge_bvec_fn which calls the corresponding function
in subsidiary devices requires that mddev->merge_check_needed
be set if any child has a merge_bvec_fn.
However were were only setting that when a device was hot-added,
not when a device was present from the start.
This bug was introduced in 3.4 so patch is suitable for 3.4.y
kernels. However that are conflicts in raid10.c so a separate
patch will be needed for 3.4.y.
Cc: stable@vger.kernel.org
Reported-by: Sebastian Riemer <sebastian.riemer@profitbricks.com>
Signed-off-by: NeilBrown <neilb@suse.de>
Main features:
- RAID10 arrays can be reshapes - adding and removing devices and
changing chunks (not 'far' array though)
- allow RAID5 arrays to be reshaped with a backup file (not tested
yet, but the priciple works fine for RAID10).
- arrays can be reshaped while a bitmap is present - you no longer
need to remove it first
- SSSE3 support for RAID6 syndrome calculations
and of course a number of minor fixes etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=q8bc
-----END PGP SIGNATURE-----
Merge tag 'md-3.5' of git://neil.brown.name/md
Pull md updates from NeilBrown:
"It's been a busy cycle for md - lots of fun stuff here.. if you like
this kind of thing :-)
Main features:
- RAID10 arrays can be reshaped - adding and removing devices and
changing chunks (not 'far' array though)
- allow RAID5 arrays to be reshaped with a backup file (not tested
yet, but the priciple works fine for RAID10).
- arrays can be reshaped while a bitmap is present - you no longer
need to remove it first
- SSSE3 support for RAID6 syndrome calculations
and of course a number of minor fixes etc."
* tag 'md-3.5' of git://neil.brown.name/md: (56 commits)
md/bitmap: record the space available for the bitmap in the superblock.
md/raid10: Remove extras after reshape to smaller number of devices.
md/raid5: improve removal of extra devices after reshape.
md: check the return of mddev_find()
MD RAID1: Further conditionalize 'fullsync'
DM RAID: Use md_error() in place of simply setting Faulty bit
DM RAID: Record and handle missing devices
DM RAID: Set recovery flags on resume
md/raid5: Allow reshape while a bitmap is present.
md/raid10: resize bitmap when required during reshape.
md: allow array to be resized while bitmap is present.
md/bitmap: make sure reshape request are reflected in superblock.
md/bitmap: add bitmap_resize function to allow bitmap resizing.
md/bitmap: use DIV_ROUND_UP instead of open-code
md/bitmap: create a 'struct bitmap_counts' substructure of 'struct bitmap'
md/bitmap: make bitmap bitops atomic.
md/bitmap: make _page_attr bitops atomic.
md/bitmap: merge bitmap_file_unmap and bitmap_file_put.
md/bitmap: remove async freeing of bitmap file.
md/bitmap: convert some spin_lock_irqsave to spin_lock_irq
...
Now that bitmaps can grow and shrink it is best if we record
how much space is available. This means that when
we reduce the size of the bitmap we won't "lose" the space
for late when we might want to increase the size of the bitmap
again.
Signed-off-by: NeilBrown <neilb@suse.de>
When a reshape which reduced the number of devices finishes
we must remove the extra devices.
So ensure that raid10_remove_disk won't try to keep them, and
have raid10_finish_reshape clear the 'in_sync' flag. Then
remove_and_add_spares will be able to remove them.
Reported-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: NeilBrown <neilb@suse.de>
After a reshape which reduced the number of devices we need
to disconnect the extra devices.
The code for this doesn't currently handle 'replacement' devices.
It is very unlikely that such devices will be present, but it is
safest to handle them anyway.
So simplify the handling. Just clear In_sync and leave it
to remove_and_add_spaces (which will be called soon) to do
the real works.
Signed-off-by: NeilBrown <neilb@suse.de>
Check the return of mddev_find(), since it may fail due to out of
memeory or out of usable minor number.
The reason I chose -ENODEV instead of -ENOMEM or something else is
md_alloc() function chose that ;)
Signed-off-by: Yuanhan Liu <yuanhan.liu@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
A RAID1 device does not necessarily need a fullsync if the bitmap can be used instead.
Similar to commit d6b212f4b1 in raid5.c, if a raid1
device can be brought back (i.e. from a transient failure) it shouldn't need a
complete resync. Provided the bitmap is not to old, it will have recorded the areas
of the disk that need recovery.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
NeilBrown