Converts the hrtimer code to use the new timerlist infrastructure
Signed-off-by: John Stultz <john.stultz@linaro.org>
LKML Reference: <1290136329-18291-3-git-send-email-john.stultz@linaro.org>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
CC: Alessandro Zummo <a.zummo@towertech.it>
CC: Thomas Gleixner <tglx@linutronix.de>
CC: Richard Cochran <richardcochran@gmail.com>
Replace sizeof(buffer)/sizeof(buffer[0]) with ARRAY_SIZE(buffer) in
kernel/time/timecompare.c
Signed-off-by: Nikitas Angelinas <nikitasangelinas@googlemail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the clocksource is not a multiple of HZ, the clock will be off. For
acpi_pm, HZ=1000 the error is 127.111 ppm:
The rounding of cycle_interval ends up generating a false error term in
ntp_error accumulation since xtime_interval is not exactly 1/HZ. So, we
subtract out the error caused by the rounding.
This has been visible since 2.6.32-rc2
commit a092ff0f90
time: Implement logarithmic time accumulation
That commit raised NTP_INTERVAL_FREQ and exposed the rounding error.
testing tool: http://n1.taur.dk/permanent/testpmt.c
Also tested with ntpd and a frequency counter.
Signed-off-by: Kasper Pedersen <kkp2010@kasperkp.dk>
Acked-by: john stultz <johnstul@us.ibm.com>
Cc: John Kacur <jkacur@redhat.com>
Cc: Clark Williams <williams@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Clamp update interval to reduce PLL gain with low sampling rate (e.g.
intermittent network connection) to avoid instability.
The clamp roughly corresponds to the loop time constant, it's 8 * poll
interval for SHIFT_PLL 2 and 32 * poll interval for SHIFT_PLL 4. This
gives good results without affecting the gain in normal conditions where
ntpd skips only up to seven consecutive samples.
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: john stultz <johnstul@us.ibm.com>
LKML-Reference: <1283870626-9472-1-git-send-email-mlichvar@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Early 4.3 versions of gcc apparently aggressively optimize the raw
time accumulation loop, replacing it with a divide.
On 32bit systems, this causes the following link errors:
undefined reference to `__umoddi3'
undefined reference to `__udivdi3'
The gcc issue has been fixed in 4.4 and greater.
This patch replaces the accumulation loop with a do_div, as suggested
by Linus.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
CC: Jason Wessel <jason.wessel@windriver.com>
CC: Larry Finger <Larry.Finger@lwfinger.net>
CC: Ingo Molnar <mingo@elte.hu>
CC: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The tv_nsec is a long and when added to the shifted interval it can wrap
and become negative which later causes looping problems in the
getrawmonotonic(). The edge case occurs when the system has slept for
a short period of time of ~2 seconds.
A trace printk of the values in this patch illustrate the problem:
ftrace time stamp: log
43.716079: logarithmic_accumulation: raw: 3d0913 tv_nsec d687faa
43.718513: logarithmic_accumulation: raw: 3d0913 tv_nsec da588bd
43.722161: logarithmic_accumulation: raw: 3d0913 tv_nsec de291d0
46.349925: logarithmic_accumulation: raw: 7a122600 tv_nsec e1f9ae3
46.349930: logarithmic_accumulation: raw: 1e848980 tv_nsec 8831c0e3
The kernel starts looping at 46.349925 in the getrawmonotonic() due to
the negative value from adding the raw value to tv_nsec.
A simple solution is to accumulate into a u64, and then normalize it
to a timespec_t.
Signed-off-by: Jason Wessel <jason.wessel@windriver.com>
[ Reworked variable names and simplified some of the code. - John ]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'timers-timekeeping-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
um: Fix read_persistent_clock fallout
kgdb: Do not access xtime directly
powerpc: Clean up obsolete code relating to decrementer and timebase
powerpc: Rework VDSO gettimeofday to prevent time going backwards
clocksource: Add __clocksource_updatefreq_hz/khz methods
x86: Convert common clocksources to use clocksource_register_hz/khz
timekeeping: Make xtime and wall_to_monotonic static
hrtimer: Cleanup direct access to wall_to_monotonic
um: Convert to use read_persistent_clock
timkeeping: Fix update_vsyscall to provide wall_to_monotonic offset
powerpc: Cleanup xtime usage
powerpc: Simplify update_vsyscall
time: Kill off CONFIG_GENERIC_TIME
time: Implement timespec_add
x86: Fix vtime/file timestamp inconsistencies
Trivial conflicts in Documentation/feature-removal-schedule.txt
Much less trivial conflicts in arch/powerpc/kernel/time.c resolved as
per Thomas' earlier merge commit 47916be4e2 ("Merge branch
'powerpc.cherry-picks' into timers/clocksource")
* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
Documentation: Add timers/timers-howto.txt
timer: Added usleep_range timer
Revert "timer: Added usleep[_range] timer"
clockevents: Remove the per cpu tick skew
posix_timer: Move copy_to_user(created_timer_id) down in timer_create()
timer: Added usleep[_range] timer
timers: Document meaning of deferrable timer
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (27 commits)
sched: Use correct macro to display sched_child_runs_first in /proc/sched_debug
sched: No need for bootmem special cases
sched: Revert nohz_ratelimit() for now
sched: Reduce update_group_power() calls
sched: Update rq->clock for nohz balanced cpus
sched: Fix spelling of sibling
sched, cpuset: Drop __cpuexit from cpu hotplug callbacks
sched: Fix the racy usage of thread_group_cputimer() in fastpath_timer_check()
sched: run_posix_cpu_timers: Don't check ->exit_state, use lock_task_sighand()
sched: thread_group_cputime: Simplify, document the "alive" check
sched: Remove the obsolete exit_state/signal hacks
sched: task_tick_rt: Remove the obsolete ->signal != NULL check
sched: __sched_setscheduler: Read the RLIMIT_RTPRIO value lockless
sched: Fix comments to make them DocBook happy
sched: Fix fix_small_capacity
powerpc: Exclude arch_sd_sibiling_asym_packing() on UP
powerpc: Enable asymmetric SMT scheduling on POWER7
sched: Add asymmetric group packing option for sibling domain
sched: Fix capacity calculations for SMT4
sched: Change nohz idle load balancing logic to push model
...
Historically, Linux has tried to make the regular timer tick on the
various CPUs not happen at the same time, to avoid contention on
xtime_lock.
Nowadays, with the tickless kernel, this contention no longer happens
since time keeping and updating are done differently. In addition,
this skew is actually hurting power consumption in a measurable way on
many-core systems.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
LKML-Reference: <20100727210210.58d3118c@infradead.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To properly handle clocksources that change frequencies
at the clocksource->enable() point, this patch adds
a method that will update the clocksource's mult/shift and
max_idle_ns values.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-12-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch makes xtime and wall_to_monotonic static, as planned in
Documentation/feature-removal-schedule.txt. This will allow for
further cleanups to the timekeeping core.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-10-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Provides an accessor function to replace hrtimer.c's
direct access of wall_to_monotonic.
This will allow wall_to_monotonic to be made static as
planned in Documentation/feature-removal-schedule.txt
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-9-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
update_vsyscall() did not provide the wall_to_monotoinc offset,
so arch specific implementations tend to reference wall_to_monotonic
directly. This limits future cleanups in the timekeeping core, so
this patch fixes the update_vsyscall interface to provide
wall_to_monotonic, allowing wall_to_monotonic to be made static
as planned in Documentation/feature-removal-schedule.txt
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Anton Blanchard <anton@samba.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Tony Luck <tony.luck@intel.com>
LKML-Reference: <1279068988-21864-7-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Now that all arches have been converted over to use generic time via
clocksources or arch_gettimeoffset(), we can remove the GENERIC_TIME
config option and simplify the generic code.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-4-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
After accidentally misusing timespec_add_safe, I wanted to make sure
we don't accidently trip over that issue again, so I created a simple
timespec_add() function which we can use to replace the instances
of timespec_add_safe() that don't want the overflow detection.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-3-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Norbert reported that nohz_ratelimit() causes his laptop to burn about
4W (40%) extra. For now back out the change and see if we can adjust
the power management code to make better decisions.
Reported-by: Norbert Preining <preining@logic.at>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Acked-by: Mike Galbraith <efault@gmx.de>
Cc: Arjan van de Ven <arjan@infradead.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Commit 0224cf4c5e (sched: Intoduce get_cpu_iowait_time_us())
broke things by not making sure preemption was indeed disabled
by the callers of nr_iowait_cpu() which took the iowait value of
the current cpu.
This resulted in a heap of preempt warnings. Cure this by making
nr_iowait_cpu() take a cpu number and fix up the callers to pass
in the right number.
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Arjan van de Ven <arjan@infradead.org>
Cc: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Jiri Slaby <jslaby@suse.cz>
Cc: linux-pm@lists.linux-foundation.org
LKML-Reference: <1277968037.1868.120.camel@laptop>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Chris Wedgwood reports that 39c0cbe (sched: Rate-limit nohz) causes a
serial console regression, unresponsiveness, and indeed it does. The
reason is that the nohz code is skipped even when the tick was already
stopped before the nohz_ratelimit(cpu) condition changed.
Move the nohz_ratelimit() check to the other conditions which prevent
long idle sleeps.
Reported-by: Chris Wedgwood <cw@f00f.org>
Tested-by: Brian Bloniarz <bmb@athenacr.com>
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Greg KH <gregkh@suse.de>
Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Jef Driesen <jefdriesen@telenet.be>
LKML-Reference: <1276790557.27822.516.camel@twins>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In the new push model, all idle CPUs indeed go into nohz mode. There is
still the concept of idle load balancer (performing the load balancing
on behalf of all the idle cpu's in the system). Busy CPU kicks the nohz
balancer when any of the nohz CPUs need idle load balancing.
The kickee CPU does the idle load balancing on behalf of all idle CPUs
instead of the normal idle balance.
This addresses the below two problems with the current nohz ilb logic:
* the idle load balancer continued to have periodic ticks during idle and
wokeup frequently, even though it did not have any rebalancing to do on
behalf of any of the idle CPUs.
* On x86 and CPUs that have APIC timer stoppage on idle CPUs, this
periodic wakeup can result in a periodic additional interrupt on a CPU
doing the timer broadcast.
Also currently we are migrating the unpinned timers from an idle to the cpu
doing idle load balancing (when all the cpus in the system are idle,
there is no idle load balancing cpu and timers get added to the same idle cpu
where the request was made. So the existing optimization works only on semi idle
system).
And In semi idle system, we no longer have periodic ticks on the idle load
balancer CPU. Using that cpu will add more delays to the timers than intended
(as that cpu's timer base may not be uptodate wrt jiffies etc). This was
causing mysterious slowdowns during boot etc.
For now, in the semi idle case, use the nearest busy cpu for migrating timers
from an idle cpu. This is good for power-savings anyway.
Signed-off-by: Venkatesh Pallipadi <venki@google.com>
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <1274486981.2840.46.camel@sbs-t61.sc.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: Add clocksource_register_hz/khz interface
posix-cpu-timers: Optimize run_posix_cpu_timers()
time: Remove xtime_cache
mqueue: Convert message queue timeout to use hrtimers
hrtimers: Provide schedule_hrtimeout for CLOCK_REALTIME
timers: Introduce the concept of timer slack for legacy timers
ntp: Remove tickadj
ntp: Make time_adjust static
time: Add xtime, wall_to_monotonic to feature-removal-schedule
timer: Try to survive timer callback preempt_count leak
timer: Split out timer function call
timer: Print function name for timer callbacks modifying preemption count
time: Clean up warp_clock()
cpu-timers: Avoid iterating over all threads in fastpath_timer_check()
cpu-timers: Change SIGEV_NONE timer implementation
cpu-timers: Return correct previous timer reload value
cpu-timers: Cleanup arm_timer()
cpu-timers: Simplify RLIMIT_CPU handling
How to pick good mult/shift pairs has always been difficult to
describe to folks writing clocksource drivers, since it requires
careful tradeoffs in adjustment accuracy vs overflow limits.
Now, with the clocks_calc_mult_shift function, its much
easier. However, not many clocksources have converted to using that
function, and there is still the issue of the max interval length
assumption being made by each clocksource driver independently.
So this patch simplifies the registration process by having
clocksources be registered with a hz/khz value and the registration
function taking care of setting mult/shift.
This should take most of the confusion out of writing a clocksource
driver.
Additionally it also keeps the shift size tradeoff (more accuracy vs
longer possible nohz times) centralized so the timekeeping core can
keep track of the assumptions being made.
[ tglx: Coding style and comments fixed ]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1273280858-30143-1-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
For the ondemand cpufreq governor, it is desired that the iowait
time is microaccounted in a similar way as idle time is.
This patch introduces the infrastructure to account and expose
this information via the get_cpu_iowait_time_us() function.
[akpm@linux-foundation.org: fix CONFIG_NO_HZ=n build]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: davej@redhat.com
LKML-Reference: <20100509082523.284feab6@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Now that the only user of ts->idle_lastupdate is
update_ts_time_stats(), the entire field can be eliminated.
In update_ts_time_stats(), idle_lastupdate is first set to
"now", and a few lines later, the only user is an if() statement
that assigns a variable either to "now" or to
ts->idle_lastupdate, which has the value of "now" at that point.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: davej@redhat.com
LKML-Reference: <20100509082439.2fab0b4f@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This patch folds the updating of the last_update_time into the
update_ts_time_stats() function, and updates the callers.
This allows for further cleanups that are done in the next
patch.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: davej@redhat.com
LKML-Reference: <20100509082403.60072967@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Right now, get_cpu_idle_time_us() only reports the idle
statistics upto the point the CPU entered last idle; not what is
valid right now.
This patch adds an update of the idle statistics to
get_cpu_idle_time_us(), so that calling this function always
returns statistics that are accurate at the point of the call.
This includes resetting the start of the idle time for
accounting purposes to avoid double accounting.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: davej@redhat.com
LKML-Reference: <20100509082323.2d2f1945@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Currently, two places update the idle statistics (and more to
come later in this series).
This patch creates a helper function for updating these
statistics.
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: davej@redhat.com
LKML-Reference: <20100509082245.163e67ed@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The exported function get_cpu_idle_time_us() has no comment
describing it; add a kerneldoc comment
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Reviewed-by: Rik van Riel <riel@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: davej@redhat.com
LKML-Reference: <20100509082208.7cb721f0@infradead.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
With the earlier logarithmic time accumulation patch, xtime will now
always be within one "tick" of the current time, instead of possibly
half a second off.
This removes the need for the xtime_cache value, which always stored the
time at the last interrupt, so this patch cleans that up removing the
xtime_cache related code.
This patch also addresses an issue with an earlier version of this change,
where xtime_cache was normalizing xtime, which could in some cases be
not valid (ie: tv_nsec == NSEC_PER_SEC). This is fixed by handling
the edge case in update_wall_time().
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Petr Titěra <P.Titera@century.cz>
LKML-Reference: <1270589451-30773-1-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
percpu.h is included by sched.h and module.h and thus ends up being
included when building most .c files. percpu.h includes slab.h which
in turn includes gfp.h making everything defined by the two files
universally available and complicating inclusion dependencies.
percpu.h -> slab.h dependency is about to be removed. Prepare for
this change by updating users of gfp and slab facilities include those
headers directly instead of assuming availability. As this conversion
needs to touch large number of source files, the following script is
used as the basis of conversion.
http://userweb.kernel.org/~tj/misc/slabh-sweep.py
The script does the followings.
* Scan files for gfp and slab usages and update includes such that
only the necessary includes are there. ie. if only gfp is used,
gfp.h, if slab is used, slab.h.
* When the script inserts a new include, it looks at the include
blocks and try to put the new include such that its order conforms
to its surrounding. It's put in the include block which contains
core kernel includes, in the same order that the rest are ordered -
alphabetical, Christmas tree, rev-Xmas-tree or at the end if there
doesn't seem to be any matching order.
* If the script can't find a place to put a new include (mostly
because the file doesn't have fitting include block), it prints out
an error message indicating which .h file needs to be added to the
file.
The conversion was done in the following steps.
1. The initial automatic conversion of all .c files updated slightly
over 4000 files, deleting around 700 includes and adding ~480 gfp.h
and ~3000 slab.h inclusions. The script emitted errors for ~400
files.
2. Each error was manually checked. Some didn't need the inclusion,
some needed manual addition while adding it to implementation .h or
embedding .c file was more appropriate for others. This step added
inclusions to around 150 files.
3. The script was run again and the output was compared to the edits
from #2 to make sure no file was left behind.
4. Several build tests were done and a couple of problems were fixed.
e.g. lib/decompress_*.c used malloc/free() wrappers around slab
APIs requiring slab.h to be added manually.
5. The script was run on all .h files but without automatically
editing them as sprinkling gfp.h and slab.h inclusions around .h
files could easily lead to inclusion dependency hell. Most gfp.h
inclusion directives were ignored as stuff from gfp.h was usually
wildly available and often used in preprocessor macros. Each
slab.h inclusion directive was examined and added manually as
necessary.
6. percpu.h was updated not to include slab.h.
7. Build test were done on the following configurations and failures
were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my
distributed build env didn't work with gcov compiles) and a few
more options had to be turned off depending on archs to make things
build (like ipr on powerpc/64 which failed due to missing writeq).
* x86 and x86_64 UP and SMP allmodconfig and a custom test config.
* powerpc and powerpc64 SMP allmodconfig
* sparc and sparc64 SMP allmodconfig
* ia64 SMP allmodconfig
* s390 SMP allmodconfig
* alpha SMP allmodconfig
* um on x86_64 SMP allmodconfig
8. percpu.h modifications were reverted so that it could be applied as
a separate patch and serve as bisection point.
Given the fact that I had only a couple of failures from tests on step
6, I'm fairly confident about the coverage of this conversion patch.
If there is a breakage, it's likely to be something in one of the arch
headers which should be easily discoverable easily on most builds of
the specific arch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
Now that no arches are accessing time_adjust directly,
make it static.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1268968769-19209-1-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The logarithmic accumulation done in the timekeeping has some overflow
protection that limits the max shift value. That means it will take
more then shift loops to accumulate all of the cycles. This causes
the shift decrement to underflow, which causes the loop to never exit.
The simplest fix would be simply to do a:
if (shift)
shift--;
However that is not optimal, as we know the cycle offset is larger
then the interval << shift, the above would make shift drop to zero,
then we would be spinning for quite awhile accumulating at interval
chunks at a time.
Instead, this patch only decreases shift if the offset is smaller
then cycle_interval << shift. This makes sure we accumulate using
the largest chunks possible without overflowing tick_length, and limits
the number of iterations through the loop.
This issue was found and reported by Sonic Zhang, who also tested the fix.
Many thanks your explanation and testing!
Reported-by: Sonic Zhang <sonic.adi@gmail.com>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Tested-by: Sonic Zhang <sonic.adi@gmail.com>
LKML-Reference: <1268948850-5225-1-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The current logic which handles clock events programming failures can
increase min_delta_ns unlimited and even can cause overflows.
Sanitize it by:
- prevent zero increase when min_delta_ns == 1
- limiting min_delta_ns to a jiffie
- bail out if the jiffie limit is hit
- add retries stats for /proc/timer_list so we can gather data
Reported-by: Uwe Kleine-Koenig <u.kleine-koenig@pengutronix.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Entering nohz code on every micro-idle is costing ~10% throughput for netperf
TCP_RR when scheduling cross-cpu. Rate limiting entry fixes this, but raises
ticks a bit. On my Q6600, an idle box goes from ~85 interrupts/sec to 128.
The higher the context switch rate, the more nohz entry costs. With this patch
and some cycle recovery patches in my tree, max cross cpu context switch rate is
improved by ~16%, a large portion of which of which is this ratelimiting.
Signed-off-by: Mike Galbraith <efault@gmx.de>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1268301003.6785.28.camel@marge.simson.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Aaro Koskinen reported an issue in kernel.org bugzilla #15366, where
on non-GENERIC_TIME systems, accessing
/sys/devices/system/clocksource/clocksource0/current_clocksource
results in an oops.
It seems the timekeeper/clocksource rework missed initializing the
curr_clocksource value in the !GENERIC_TIME case.
Thanks to Aaro for reporting and diagnosing the issue as well as
testing the fix!
Reported-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: stable@kernel.org
LKML-Reference: <1267475683.4216.61.camel@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Export getboottime and monotonic_to_bootbased in order to let them
could be used by following patch.
Cc: stable@kernel.org
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Marcelo Tosatti <mtosatti@redhat.com>
Add a clocksource suspend callback. This callback can be used by the
clocksource driver to shutdown and perform any kind of late suspend
activities even though the clocksource driver itself is a non-sysdev
driver.
One example where this is useful is to fix the sh_cmt.c platform driver
that today suspends using the platform bus and shuts down the clocksource
too early.
With this callback in place the sh_cmt driver will suspend using the
clocksource and clockevent hooks and leave the platform device pm
callbacks unused.
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: john stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Pass the clocksource as an argument to the clocksource resume callback.
Needed so we can point out which CMT channel the sh_cmt.c driver shall
resume.
Signed-off-by: Magnus Damm <damm@opensource.se>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
ntp.c doesn't need to access timekeeping internals directly, so change
xtime references to use the get_seconds() timekeeping interface.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: richard@rsk.demon.co.uk
LKML-Reference: <1264738844-21935-1-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Make time_esterror and time_maxerror static as no one uses them
outside of ntp.c
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: richard@rsk.demon.co.uk
LKML-Reference: <1264719761.3437.47.camel@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
commit 0f8e8ef7 (clocksource: Simplify clocksource watchdog resume
logic) introduced a potential kgdb dead lock. When the kernel is
stopped by kgdb inside code which holds watchdog_lock then kgdb dead
locks in clocksource_resume_watchdog().
clocksource_resume_watchdog() is called from kbdg via
clocksource_touch_watchdog() to avoid that the clock source watchdog
marks TSC unstable after the kernel has been stopped.
Solve this by replacing spin_lock with a spin_trylock and just return
in case the lock is held. Not resetting the watchdog might result in
TSC becoming marked unstable, but that's an acceptable penalty for
using kgdb.
The timekeeping is anyway easily screwed up by kgdb when the system
uses either jiffies or a clock source which wraps in short intervals
(e.g. pm_timer wraps about every 4.6s), so we really do not have to
worry about that occasional TSC marked unstable side effect.
The second caller of clocksource_resume_watchdog() is
clocksource_resume(). The trylock is safe here as well because the
system is UP at this point, interrupts are disabled and nothing else
can hold watchdog_lock().
Reported-by: Jason Wessel <jason.wessel@windriver.com>
LKML-Reference: <1264480000-6997-4-git-send-email-jason.wessel@windriver.com>
Cc: kgdb-bugreport@lists.sourceforge.net
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Marc reported that the BUG_ON in clockevents_notify() triggers on his
system. This happens because the kernel tries to remove an active
clock event device (used for broadcasting) from the device list.
The handling of devices which can be used as per cpu device and as a
global broadcast device is suboptimal.
The simplest solution for now (and for stable) is to check whether the
device is used as global broadcast device, but this needs to be
revisited.
[ tglx: restored the cpuweight check and massaged the changelog ]
Reported-by: Marc Dionne <marc.c.dionne@gmail.com>
Tested-by: Marc Dionne <marc.c.dionne@gmail.com>
Signed-off-by: Xiaotian Feng <dfeng@redhat.com>
LKML-Reference: <1262834564-13033-1-git-send-email-dfeng@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
This reverts commit 7bc7d63745, as
requested by John Stultz. Quoting John:
"Petr Titěra reported an issue where he saw odd atime regressions with
2.6.33 where there were a full second worth of nanoseconds in the
nanoseconds field.
He also reviewed the time code and narrowed down the problem: unhandled
overflow of the nanosecond field caused by rounding up the
sub-nanosecond accumulated time.
Details:
* At the end of update_wall_time(), we currently round up the
sub-nanosecond portion of accumulated time when storing it into xtime.
This was added to avoid time inconsistencies caused when the
sub-nanosecond portion was truncated when storing into xtime.
Unfortunately we don't handle the possible second overflow caused by
that rounding.
* Previously the xtime_cache code hid this overflow by normalizing the
xtime value when storing into the xtime_cache.
* We could try to handle the second overflow after the rounding up, but
since this affects the timekeeping's internal state, this would further
complicate the next accumulation cycle, causing small errors in ntp
steering. As much as I'd like to get rid of it, the xtime_cache code is
known to work.
* The correct fix is really to include the sub-nanosecond portion in the
timekeeping accessor function, so we don't need to round up at during
accumulation. This would greatly simplify the accumulation code.
Unfortunately, we can't do this safely until the last three
non-GENERIC_TIME arches (sparc32, arm, cris) are converted (those
patches are in -mm) and we kill off the spots where arches set xtime
directly. This is all 2.6.34 material, so I think reverting the
xtime_cache change is the best approach for now.
Many thanks to Petr for both reporting and finding the issue!"
Reported-by: Petr Titěra <P.Titera@century.cz>
Requested-by: john stultz <johnstul@us.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: Remove duplicate setting of new_base in __mod_timer()
clockevents: Prevent clockevent_devices list corruption on cpu hotplug
struct cpumask will be undefined soon with CONFIG_CPUMASK_OFFSTACK=y,
to avoid them being declared on the stack.
cpumask_bits() does what we want here (of course, this code is crap).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
To: Thomas Gleixner <tglx@linutronix.de>
ktime will overflow from 03:14:07 UTC on Tuesday, 19 January 2038,
ktime_add() in timecompare_update() will overflow a half earlier. As a
result, wrong offset will be gotten, then cause some strange problems.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Patrick Ohly <patrick.ohly@intel.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Convert locks which cannot be sleeping locks in preempt-rt to
raw_spinlocks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
Convert locks which cannot be sleeping locks in preempt-rt to
raw_spinlocks.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
Acked-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/percpu: (34 commits)
m68k: rename global variable vmalloc_end to m68k_vmalloc_end
percpu: add missing per_cpu_ptr_to_phys() definition for UP
percpu: Fix kdump failure if booted with percpu_alloc=page
percpu: make misc percpu symbols unique
percpu: make percpu symbols in ia64 unique
percpu: make percpu symbols in powerpc unique
percpu: make percpu symbols in x86 unique
percpu: make percpu symbols in xen unique
percpu: make percpu symbols in cpufreq unique
percpu: make percpu symbols in oprofile unique
percpu: make percpu symbols in tracer unique
percpu: make percpu symbols under kernel/ and mm/ unique
percpu: remove some sparse warnings
percpu: make alloc_percpu() handle array types
vmalloc: fix use of non-existent percpu variable in put_cpu_var()
this_cpu: Use this_cpu_xx in trace_functions_graph.c
this_cpu: Use this_cpu_xx for ftrace
this_cpu: Use this_cpu_xx in nmi handling
this_cpu: Use this_cpu operations in RCU
this_cpu: Use this_cpu ops for VM statistics
...
Fix up trivial (famous last words) global per-cpu naming conflicts in
arch/x86/kvm/svm.c
mm/slab.c
Xiaotian Feng triggered a list corruption in the clock events list on
CPU hotplug and debugged the root cause.
If a CPU registers more than one per cpu clock event device, then only
the active clock event device is removed on CPU_DEAD. The unused
devices are kept in the clock events device list.
On CPU up the clock event devices are registered again, which means
that we list_add an already enqueued list_head. That results in list
corruption.
Resolve this by removing all devices which are associated to the dead
CPU on CPU_DEAD.
Reported-by: Xiaotian Feng <dfeng@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Xiaotian Feng <dfeng@redhat.com>
Cc: stable@kernel.org
The hrtimer_interrupt hang logic adjusts min_delta_ns based on the
execution time of the hrtimer callbacks.
This is error-prone for virtual machines, where a guest vcpu can be
scheduled out during the execution of the callbacks (and the callbacks
themselves can do operations that translate to blocking operations in
the hypervisor), which in can lead to large min_delta_ns rendering the
system unusable.
Replace the current heuristics with something more reliable. Allow the
interrupt code to try 3 times to catch up with the lost time. If that
fails use the total time spent in the interrupt handler to defer the
next timer interrupt so the system can catch up with other things
which got delayed. Limit that deferment to 100ms.
The retry events and the maximum time spent in the interrupt handler
are recorded and exposed via /proc/timer_list
Inspired by a patch from Marcelo.
Reported-by: Michael Tokarev <mjt@tls.msk.ru>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Marcelo Tosatti <mtosatti@redhat.com>
Cc: kvm@vger.kernel.org
* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers, init: Limit the number of per cpu calibration bootup messages
posix-cpu-timers: optimize and document timer_create callback
clockevents: Add missing include to pacify sparse
x86: vmiclock: Fix printk format
x86: Fix printk format due to variable type change
sparc: fix printk for change of variable type
clocksource/events: Fix fallout of generic code changes
nohz: Allow 32-bit machines to sleep for more than 2.15 seconds
nohz: Track last do_timer() cpu
nohz: Prevent clocksource wrapping during idle
nohz: Type cast printk argument
mips: Use generic mult/shift factor calculation for clocks
clocksource: Provide a generic mult/shift factor calculation
clockevents: Use u32 for mult and shift factors
nohz: Introduce arch_needs_cpu
nohz: Reuse ktime in sub-functions of tick_check_idle.
time: Remove xtime_cache
time: Implement logarithmic time accumulation
Include "tick-internal.h" in order to pick up the extern function
prototype for clockevents_shutdown(). This quiets the following sparse
build noise:
warning: symbol 'clockevents_shutdown' was not declared. Should it be static?
Signed-off-by: H Hartley Sweeten <hsweeten@visionengravers.com>
LKML-Reference: <BD79186B4FD85F4B8E60E381CAEE190901E24550@mi8nycmail19.Mi8.com>
Reviewed-by: Yong Zhang <yong.zhang0@gmail.com>
Cc: johnstul@us.ibm.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Since commit 0a544198 "timekeeping: Move NTP adjusted clock multiplier
to struct timekeeper" the clock multiplier of vsyscall is updated with
the unmodified clock multiplier of the clock source and not with the
NTP adjusted multiplier of the timekeeper.
This causes user space observerable time warps:
new CLOCK-warp maximum: 120 nsecs, 00000025c337c537 -> 00000025c337c4bf
Add a new argument "mult" to update_vsyscall() and hand in the
timekeeping internal NTP adjusted multiplier.
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Cc: "Zhang Yanmin" <yanmin_zhang@linux.intel.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Tony Luck <tony.luck@intel.com>
LKML-Reference: <1258436990.17765.83.camel@minggr.sh.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
powerpc grew a new warning due to the type change of clockevent->mult.
The architectures which use parts of the generic time keeping
infrastructure tripped over my wrong assumption that
clocksource_register is only used when GENERIC_TIME=y.
I should have looked and also I should have known better. These
renitent Gaul villages are racking my nerves. Some serious deprecating
is due.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
In the dynamic tick code, "max_delta_ns" (member of the
"clock_event_device" structure) represents the maximum sleep time
that can occur between timer events in nanoseconds.
The variable, "max_delta_ns", is defined as an unsigned long
which is a 32-bit integer for 32-bit machines and a 64-bit
integer for 64-bit machines (if -m64 option is used for gcc).
The value of max_delta_ns is set by calling the function
"clockevent_delta2ns()" which returns a maximum value of LONG_MAX.
For a 32-bit machine LONG_MAX is equal to 0x7fffffff and in
nanoseconds this equates to ~2.15 seconds. Hence, the maximum
sleep time for a 32-bit machine is ~2.15 seconds, where as for
a 64-bit machine it will be many years.
This patch changes the type of max_delta_ns to be "u64" instead of
"unsigned long" so that this variable is a 64-bit type for both 32-bit
and 64-bit machines. It also changes the maximum value returned by
clockevent_delta2ns() to KTIME_MAX. Hence this allows a 32-bit
machine to sleep for longer than ~2.15 seconds. Please note that this
patch also changes "min_delta_ns" to be "u64" too and although this is
unnecessary, it makes the patch simpler as it avoids to fixup all
callers of clockevent_delta2ns().
[ tglx: changed "unsigned long long" to u64 as we use this data type
through out the time code ]
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Cc: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1250617512-23567-3-git-send-email-jon-hunter@ti.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The previous patch which limits the sleep time to the maximum
deferment time of the time keeping clocksource has some limitations on
SMP machines: if all CPUs are idle then for all CPUs the maximum sleep
time is limited.
Solve this by keeping track of which cpu had the do_timer() duty
assigned last and limit the sleep time only for this cpu.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Cc: Jon Hunter <jon-hunter@ti.com>
Cc: John Stultz <johnstul@us.ibm.com>
The dynamic tick allows the kernel to sleep for periods longer than a
single tick, but it does not limit the sleep time currently. In the
worst case the kernel could sleep longer than the wrap around time of
the time keeping clock source which would result in losing track of
time.
Prevent this by limiting it to the safe maximum sleep time of the
current time keeping clock source. The value is calculated when the
clock source is registered.
[ tglx: simplified the code a bit and massaged the commit msg ]
Signed-off-by: Jon Hunter <jon-hunter@ti.com>
Cc: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1250617512-23567-2-git-send-email-jon-hunter@ti.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On some archs local_softirq_pending() has a data type of unsigned long
on others its unsigned int. Type cast it to (unsigned int) in the
printk to avoid the compiler warning.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
MIPS has two functions to calculcate the mult/shift factors for clock
sources and clock events at run time. ARM needs such functions as
well.
Implement a function which calculates the mult/shift factors based on
the frequencies to which and from which is converted. The function
also has a parameter to specify the minimum conversion range in
seconds. This range is guaranteed not to produce a 64bit overflow when
a value is multiplied with the calculated mult factor. The larger the
conversion range the less becomes the conversion accuracy.
Provide two inline wrappers which handle clock events and clock
sources. For clock events the "from" frequency is nano seconds per
second which corresponds to 1GHz and "to" is the device frequency. For
clock sources "from" is the device frequency and "to" is nano seconds
per second.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <20091111134229.766673305@linutronix.de>
The mult and shift factors of clock events differ in their data type
from those of clock sources for no reason. u32 is sufficient for
both. shift is always <= 32 and mult is limited to 2^32-1 to avoid
64bit multiplication overflows in the conversion.
Preparatory patch for a generic mult/shift factor calculation
function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Mikael Pettersson <mikpe@it.uu.se>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Cc: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <20091111134229.725664788@linutronix.de>
This patch was generated by
git grep -E -i -l 's(le|el)ct' | xargs -r perl -p -i -e 's/([Ss])(le|el)ct/$1elect/
with only skipping net/netfilter/xt_SECMARK.c and
include/linux/netfilter/xt_SECMARK.h which have a struct member called
selctx.
Signed-off-by: Uwe Kleine-Knig <u.kleine-koenig@pengutronix.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Allow the architecture to request a normal jiffy tick when the system
goes idle and tick_nohz_stop_sched_tick is called . On s390 the hook is
used to prevent the system going fully idle if there has been an
interrupt other than a clock comparator interrupt since the last wakeup.
On s390 the HiperSockets response time for 1 connection ping-pong goes
down from 42 to 34 microseconds. The CPU cost decreases by 27%.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
LKML-Reference: <20090929122533.402715150@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
On a system with NOHZ=y tick_check_idle calls tick_nohz_stop_idle and
tick_nohz_update_jiffies. Given the right conditions (ts->idle_active
and/or ts->tick_stopped) both function get a time stamp with ktime_get.
The same time stamp can be reused if both function require one.
On s390 this change has the additional benefit that gcc inlines the
tick_nohz_stop_idle function into tick_check_idle. The number of
instructions to execute tick_check_idle drops from 225 to 144
(without the ktime_get optimization it is 367 vs 215 instructions).
before:
0) | tick_check_idle() {
0) | tick_nohz_stop_idle() {
0) | ktime_get() {
0) | read_tod_clock() {
0) 0.601 us | }
0) 1.765 us | }
0) 3.047 us | }
0) | ktime_get() {
0) | read_tod_clock() {
0) 0.570 us | }
0) 1.727 us | }
0) | tick_do_update_jiffies64() {
0) 0.609 us | }
0) 8.055 us | }
after:
0) | tick_check_idle() {
0) | ktime_get() {
0) | read_tod_clock() {
0) 0.617 us | }
0) 1.773 us | }
0) | tick_do_update_jiffies64() {
0) 0.593 us | }
0) 4.477 us | }
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: john stultz <johnstul@us.ibm.com>
LKML-Reference: <20090929122533.206589318@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This patch updates percpu related symbols under kernel/ and mm/ such
that percpu symbols are unique and don't clash with local symbols.
This serves two purposes of decreasing the possibility of global
percpu symbol collision and allowing dropping per_cpu__ prefix from
percpu symbols.
* kernel/lockdep.c: s/lock_stats/cpu_lock_stats/
* kernel/sched.c: s/init_rq_rt/init_rt_rq_var/ (any better idea?)
s/sched_group_cpus/sched_groups/
* kernel/softirq.c: s/ksoftirqd/run_ksoftirqd/a
* kernel/softlockup.c: s/(*)_timestamp/softlockup_\1_ts/
s/watchdog_task/softlockup_watchdog/
s/timestamp/ts/ for local variables
* kernel/time/timer_stats: s/lookup_lock/tstats_lookup_lock/
* mm/slab.c: s/reap_work/slab_reap_work/
s/reap_node/slab_reap_node/
* mm/vmstat.c: local variable changed to avoid collision with vmstat_work
Partly based on Rusty Russell's "alloc_percpu: rename percpu vars
which cause name clashes" patch.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: (slab/vmstat) Christoph Lameter <cl@linux-foundation.org>
Reviewed-by: Christoph Lameter <cl@linux-foundation.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Nick Piggin <npiggin@suse.de>
After m68k's task_thread_info() doesn't refer to current,
it's possible to remove sched.h from interrupt.h and not break m68k!
Many thanks to Heiko Carstens for allowing this.
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Commit f2e21c9610 had unfortunate side
effects with cpufreq governors on some systems.
If the system did not switch into NOHZ mode ts->inidle is not set when
tick_nohz_stop_sched_tick() is called from the idle routine. Therefor
all subsequent calls from irq_exit() to tick_nohz_stop_sched_tick()
fail to call tick_nohz_start_idle(). This results in bogus idle
accounting information which is passed to cpufreq governors.
Set the inidle flag unconditionally of the NOHZ active state to keep
the idle time accounting correct in any case.
[ tglx: Added comment and tweaked the changelog ]
Reported-by: Steven Noonan <steven@uplinklabs.net>
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Cc: Rik van Riel <riel@redhat.com>
Cc: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: Greg KH <greg@kroah.com>
Cc: Steven Noonan <steven@uplinklabs.net>
Cc: stable@kernel.org
LKML-Reference: <1254907901.30157.93.camel@eenurkka-desktop>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
With the prior logarithmic time accumulation patch, xtime will now
always be within one "tick" of the current time, instead of
possibly half a second off.
This removes the need for the xtime_cache value, which always
stored the time at the last interrupt, so this patch cleans that up
removing the xtime_cache related code.
This is a bit simpler, but still could use some wider testing.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: John Kacur <jkacur@redhat.com>
Cc: Clark Williams <williams@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1254525855.7741.95.camel@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Accumulating one tick at a time works well unless we're using NOHZ.
Then it can be an issue, since we may have to run through the loop
a few thousand times, which can increase timer interrupt caused
latency.
The current solution was to accumulate in half-second intervals
with NOHZ. This kept the number of loops down, however it did
slightly change how we make NTP adjustments. While not an issue
with NTPd users, as NTPd makes adjustments over a longer period of
time, other adjtimex() users have noticed the half-second
granularity with which we can apply frequency changes to the clock.
For instance, if a application tries to apply a 100ppm frequency
correction for 20ms to correct a 2us offset, with NOHZ they either
get no correction, or a 50us correction.
Now, there will always be some granularity error for applying
frequency corrections. However with users sensitive to this error
have seen a 50-500x increase with NOHZ compared to running without
NOHZ.
So I figured I'd try another approach then just simply increasing
the interval. My approach is to consume the time interval
logarithmically. This reduces the number of times through the loop
needed keeping latency down, while still preserving the original
granularity error for adjtimex() changes.
Further, this change allows us to remove the xtime_cache code
(patch to follow), as xtime is always within one tick of the
current time, instead of the half-second updates it saw before.
An earlier version of this patch has been shipping to x86 users in
the RedHat MRG releases for awhile without issue, but I've reworked
this version to be even more careful about avoiding possible
overflows if the shift value gets too large.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: John Kacur <jkacur@redhat.com>
Cc: Clark Williams <williams@redhat.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
LKML-Reference: <1254525473.7741.88.camel@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'timers-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: Resume clocksource without taking the clocksource mutex
git commit 75c5158f70 converted the clocksource spinlock to a
mutex. This causes the following BUG:
BUG: sleeping function called from invalid context at
kernel/mutex.c:280 in_atomic(): 0, irqs_disabled(): 1, pid: 2473,
name: pm-suspend 2 locks held by pm-suspend/2473:
#0: (&buffer->mutex){......}, at: [<ffffffff8115ab13>]
sysfs_write_file+0x3c/0x137
#1: (pm_mutex){......}, at: [<ffffffff810865b5>]
enter_state+0x39/0x130 Pid: 2473, comm: pm-suspend Not tainted 2.6.31
#1 Call Trace:
[<ffffffff810792f0>] ? __debug_show_held_locks+0x22/0x24
[<ffffffff8104a2ef>] __might_sleep+0x107/0x10b
[<ffffffff8141fca9>] mutex_lock_nested+0x25/0x43
[<ffffffff81073537>] clocksource_resume+0x1c/0x60
[<ffffffff81072902>] timekeeping_resume+0x1e/0x1c8
[<ffffffff812aee62>] __sysdev_resume+0x25/0xcf
[<ffffffff812aef79>] sysdev_resume+0x6d/0xae
[<ffffffff810864f8>] suspend_devices_and_enter+0x12b/0x1af
[<ffffffff8108665b>] enter_state+0xdf/0x130
[<ffffffff81085dc3>] state_store+0xb6/0xd3
[<ffffffff81204c73>] kobj_attr_store+0x17/0x19
[<ffffffff8115abd2>] sysfs_write_file+0xfb/0x137
[<ffffffff811057d2>] vfs_write+0xae/0x10b
[<ffffffff81208392>] ? __up_read+0x1a/0x7f
[<ffffffff811058ef>] sys_write+0x4a/0x6e
[<ffffffff81011b82>] system_call_fastpath+0x16/0x1b
clocksource_resume is called early in the resume process, there is
only one cpu, no processes are running and the interrupts are
disabled. It is therefore possible to resume the clocksources
without taking the clocksource mutex.
Reported-by: Xiaotian Feng <xtfeng@gmail.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Tested-by: Michal Schmidt <mschmidt@redhat.com>
Cc: Xiaotian Feng <xtfeng@gmail.com>
Cc: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <20090924172952.49697825@mschwide.boeblingen.de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
There are many similar code in kernel for one object: convert time between
calendar time and broken-down time.
Here is some source I found:
fs/ncpfs/dir.c
fs/smbfs/proc.c
fs/fat/misc.c
fs/udf/udftime.c
fs/cifs/netmisc.c
net/netfilter/xt_time.c
drivers/scsi/ips.c
drivers/input/misc/hp_sdc_rtc.c
drivers/rtc/rtc-lib.c
arch/ia64/hp/sim/boot/fw-emu.c
arch/m68k/mac/misc.c
arch/powerpc/kernel/time.c
arch/parisc/include/asm/rtc.h
...
We can make a common function for this type of conversion, At least we
can get following benefit:
1: Make kernel simple and unify
2: Easy to fix bug in converting code
3: Reduce clone of code in future
For example, I'm trying to make ftrace display walltime,
this patch will make me easy.
This code is based on code from glibc-2.6
Signed-off-by: Zhao Lei <zhaolei@cn.fujitsu.com>
Cc: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'timers-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (34 commits)
time: Prevent 32 bit overflow with set_normalized_timespec()
clocksource: Delay clocksource down rating to late boot
clocksource: clocksource_select must be called with mutex locked
clocksource: Resolve cpu hotplug dead lock with TSC unstable, fix crash
timers: Drop a function prototype
clocksource: Resolve cpu hotplug dead lock with TSC unstable
timer.c: Fix S/390 comments
timekeeping: Fix invalid getboottime() value
timekeeping: Fix up read_persistent_clock() breakage on sh
timekeeping: Increase granularity of read_persistent_clock(), build fix
time: Introduce CLOCK_REALTIME_COARSE
x86: Do not unregister PIT clocksource on PIT oneshot setup/shutdown
clocksource: Avoid clocksource watchdog circular locking dependency
clocksource: Protect the watchdog rating changes with clocksource_mutex
clocksource: Call clocksource_change_rating() outside of watchdog_lock
timekeeping: Introduce read_boot_clock
timekeeping: Increase granularity of read_persistent_clock()
timekeeping: Update clocksource with stop_machine
timekeeping: Add timekeeper read_clock helper functions
timekeeping: Move NTP adjusted clock multiplier to struct timekeeper
...
Fix trivial conflict due to MIPS lemote -> loongson renaming.
The down rating of clock sources in the early boot process via the
clock source watchdog mechanism can happen way before the per cpu
event queues are initialized. This leads to a boot crash on x86 when
the TSC is marked unstable in the SMP bring up.
The selection of a clock source for time keeping happens in the late
boot process so we can safely delay the list manipulation until
clocksource_done_booting() is called.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
The callers of clocksource_select must hold clocksource_mutex to
protect the clocksource_list.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
The watchdog timer is started after the watchdog clocksource
and at least one watched clocksource have been registered. The
clocksource work element watchdog_work is initialized just
before the clocksource timer is started. This is too late for
the clocksource_mark_unstable call from native_cpu_up. To fix
this use a static initializer for watchdog_work.
This resolves a boot crash reported by multiple people.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Jens Axboe <jens.axboe@oracle.com>
Cc: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <20090911153305.3fe9a361@skybase>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Martin Schwidefsky analyzed it:
To register a clocksource the clocksource_mutex is acquired and if
necessary timekeeping_notify is called to install the clocksource as
the timekeeper clock. timekeeping_notify uses stop_machine which needs
to take cpu_add_remove_lock mutex.
Starting a new cpu is done with the cpu_add_remove_lock mutex held.
native_cpu_up checks the tsc of the new cpu and if the tsc is no good
clocksource_change_rating is called. Which needs the clocksource_mutex
and the deadlock is complete.
The solution is to replace the TSC via the clocksource watchdog
mechanism. Mark the TSC as unstable and schedule the watchdog work so
it gets removed in the watchdog thread context.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
LKML-Reference: <new-submission>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: John Stultz <johnstul@us.ibm.com>
Don't use timespec_add_safe() with wall_to_monotonic, because
wall_to_monotonic has negative values which will cause overflow
in timespec_add_safe(). That makes btime in /proc/stat invalid.
Signed-off-by: Hiroshi Shimamoto <h-shimamoto@ct.jp.nec.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <4A937FDE.4050506@ct.jp.nec.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
After talking with some application writers who want very fast, but not
fine-grained timestamps, I decided to try to implement new clock_ids
to clock_gettime(): CLOCK_REALTIME_COARSE and CLOCK_MONOTONIC_COARSE
which returns the time at the last tick. This is very fast as we don't
have to access any hardware (which can be very painful if you're using
something like the acpi_pm clocksource), and we can even use the vdso
clock_gettime() method to avoid the syscall. The only trade off is you
only get low-res tick grained time resolution.
This isn't a new idea, I know Ingo has a patch in the -rt tree that made
the vsyscall gettimeofday() return coarse grained time when the
vsyscall64 sysctrl was set to 2. However this affects all applications
on a system.
With this method, applications can choose the proper speed/granularity
trade-off for themselves.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: nikolag@ca.ibm.com
Cc: Darren Hart <dvhltc@us.ibm.com>
Cc: arjan@infradead.org
Cc: jonathan@jonmasters.org
LKML-Reference: <1250734414.6897.5.camel@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Currently clockevents_notify() is called with interrupts enabled at
some places and interrupts disabled at some other places.
This results in a deadlock in this scenario.
cpu A holds clockevents_lock in clockevents_notify() with irqs enabled
cpu B waits for clockevents_lock in clockevents_notify() with irqs disabled
cpu C doing set_mtrr() which will try to rendezvous of all the cpus.
This will result in C and A come to the rendezvous point and waiting
for B. B is stuck forever waiting for the spinlock and thus not
reaching the rendezvous point.
Fix the clockevents code so that clockevents_lock is taken with
interrupts disabled and thus avoid the above deadlock.
Also call lapic_timer_propagate_broadcast() on the destination cpu so
that we avoid calling smp_call_function() in the clockevents notifier
chain.
This issue left us wondering if we need to change the MTRR rendezvous
logic to use stop machine logic (instead of smp_call_function) or add
a check in spinlock debug code to see if there are other spinlocks
which gets taken under both interrupts enabled/disabled conditions.
Signed-off-by: Suresh Siddha <suresh.b.siddha@intel.com>
Signed-off-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Cc: "Pallipadi Venkatesh" <venkatesh.pallipadi@intel.com>
Cc: "Brown Len" <len.brown@intel.com>
LKML-Reference: <1250544899.2709.210.camel@sbs-t61.sc.intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
stop_machine from a multithreaded workqueue is not allowed because
of a circular locking dependency between cpu_down and the workqueue
execution. Use a kernel thread to do the clocksource downgrade.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: john stultz <johnstul@us.ibm.com>
LKML-Reference: <20090818170942.3ab80c91@skybase>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Martin pointed out that commit 6ea41d2529 (clocksource: Call
clocksource_change_rating() outside of watchdog_lock) has a
theoretical reference count problem. The calls to
clocksource_change_rating() are now done outside of the clocksource
mutex and outside of the watchdog lock. A concurrent
clocksource_unregister() could remove the clock.
Split out the code which changes the rating from
clocksource_change_rating() into __clocksource_change_rating().
Protect the clocksource_watchdog_work() code sequence with the
clocksource_mutex() and call __clocksource_change_rating().
LKML-Reference: <alpine.LFD.2.00.0908171038420.2782@localhost.localdomain>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
/proc/timer_list and /proc/slabinfo are not supposed to be
written, so there should be no write permissions on it.
Signed-off-by: WANG Cong <amwang@redhat.com>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Vegard Nossum <vegard.nossum@gmail.com>
Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Cc: linux-mm@kvack.org
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: David Rientjes <rientjes@google.com>
Cc: Amerigo Wang <amwang@redhat.com>
Cc: Matt Mackall <mpm@selenic.com>
Cc: Arjan van de Ven <arjan@linux.intel.com>
LKML-Reference: <20090817094525.6355.88682.sendpatchset@localhost.localdomain>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
The changes to the watchdog logic introduced a lock inversion between
watchdog_lock and clocksource_mutex. Change the rating outside of
watchdog_lock to avoid it.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add the new function read_boot_clock to get the exact time the system
has been started. For architectures without support for exact boot
time a new weak function is added that returns 0. Use the exact boot
time to initialize wall_to_monotonic, or xtime if the read_boot_clock
returned 0.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134811.296703241@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The persistent clock of some architectures (e.g. s390) have a
better granularity than seconds. To reduce the delta between the
host clock and the guest clock in a virtualized system change the
read_persistent_clock function to return a struct timespec.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134811.013873340@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
update_wall_time calls change_clocksource HZ times per second to check
if a new clock source is available. In close to 100% of all calls
there is no new clock. Replace the tick based check by an update done
with stop_machine.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134810.711836357@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add timekeeper_read_clock_ntp and timekeeper_read_clock_raw and use
them for getnstimeofday, ktime_get, ktime_get_ts and getrawmonotonic.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134810.435105711@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The clocksource structure has two multipliers, the unmodified multiplier
clock->mult_orig and the NTP corrected multiplier clock->mult. The NTP
multiplier is misplaced in the struct clocksource, this is private
information of the timekeeping code. Add the mult field to the struct
timekeeper to contain the NTP corrected value, keep the unmodifed
multiplier in clock->mult and remove clock->mult_orig.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134810.149047645@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The xtime_nsec value in the timekeeper structure is shifted by a few
bits to improve precision. This happens to be the same value as the
clock->shift. To improve readability add xtime_shift to the timekeeper
and use it instead of the clock->shift. Likewise add ntp_error_shift
and replace all (NTP_SCALE_SHIFT - clock->shift) expressions.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134809.871899606@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Add struct timekeeper to keep the internal values timekeeping.c needs
in regard to the currently selected clock source. This moves the
timekeeping intervals, xtime_nsec and the ntp error value from struct
clocksource to struct timekeeper. The raw_time is removed from the
clocksource as well. It gets treated like xtime as a global variable.
Eventually xtime raw_time should be moved to struct timekeeper.
[ tglx: minor cleanup ]
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134809.613209842@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move the downgrade of an unstable clocksource from the timer interrupt
context into the process context of a work queue thread. This is
needed to be able to do the clocksource switch with stop_machine.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134809.354926067@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Refactor clocksource watchdog code to make it more readable. Add
clocksource_dequeue_watchdog to remove a clocksource from the watchdog
list when it is unregistered.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134809.110881699@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
To resume the clocksource watchdog just remove the CLOCK_SOURCE_WATCHDOG
bit from the watched clocksource.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134808.880925790@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The clocksource watchdog marks a clock as highres capable before it
checked the deviation from the watchdog clocksource even for a single
time. Make sure that the deviation is at least checked once before
doing the switch to highres mode.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Ingo Molnar <mingo@elte.hu>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134808.627795883@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
If a non high-resolution clocksource is first set as override clock
and then registered it becomes active even if the system is in one-shot
mode. Move the override check from sysfs_override_clocksource to the
clocksource selection. That fixes the bug and simplifies the code. The
check in clocksource_register for double registration of the same
clocksource is removed without replacement.
To find the initial clocksource a new weak function in jiffies.c is
defined that returns the jiffies clocksource. The architecture code
can then override the weak function with a more suitable clocksource,
e.g. the TOD clock on s390.
[ tglx: Folded in a fix from John Stultz ]
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134808.388024160@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
change_clocksource resets the cycle_last value to zero then sets it to
a value read from the clocksource. The reset to zero is required only
for the TSC clocksource to make the read_tsc function work after a
resume. The reason is that the TSC read function uses cycle_last to
detect backwards going TSCs. In the resume case cycle_last contains
the TSC value from the last update before the suspend. On resume the
TSC starts counting from 0 again and would trip over the cycle_last
comparison.
This is subtle and surprising. Move the reset to a resume function in
the tsc code.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134808.142191175@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The three inline functions clocksource_read, clocksource_enable and
clocksource_disable are simple wrappers of an indirect call plus the
copy from and to the mult_orig value. The functions are exclusively
used by the timekeeping code which has intimate knowledge of the
clocksource anyway. Therefore remove the inline functions. No
functional change.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Daniel Walker <dwalker@fifo99.com>
LKML-Reference: <20090814134807.903108946@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Move the adjustment of xtime, wall_to_monotonic and the update of the
vsyscall variables to the timekeeping code.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
LKML-Reference: <20090814134807.609730216@de.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Writing a zero length string to sys/.../current_clocksource will cause
a NULL pointer dereference if the clock events system is in one shot
(highres or nohz) mode.
Pointed-out-by: Dan Carpenter <error27@gmail.com>
LKML-Reference: <alpine.DEB.2.00.0907191545580.12306@bicker>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The timer migration expiry check should prevent the migration of a
timer to another CPU when the timer expires before the next event is
scheduled on the other CPU. Migrating the timer might delay it because
we can not reprogram the clock event device on the other CPU. But the
code implementing that check has two flaws:
- for !HIGHRES the check compares the expiry value with the clock
events device expiry value which is wrong for CLOCK_REALTIME based
timers.
- the check is racy. It holds the hrtimer base lock of the target CPU,
but the clock event device expiry value can be modified
nevertheless, e.g. by an timer interrupt firing.
The !HIGHRES case is easy to fix as we can enqueue the timer on the
cpu which was selected by the load balancer. It runs the idle
balancing code once per jiffy anyway. So the maximum delay for the
timer is the same as when we keep the tick on the current cpu going.
In the HIGHRES case we can get the next expiry value from the hrtimer
cpu_base of the target CPU and serialize the update with the cpu_base
lock. This moves the lock section in hrtimer_interrupt() so we can set
next_event to KTIME_MAX while we are handling the expired timers and
set it to the next expiry value after we handled the timers under the
base lock. While the expired timers are processed timer migration is
blocked because the expiry time of the timer is always <= KTIME_MAX.
Also remove the now useless clockevents_get_next_event() function.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The ktime_get() functions for GENERIC_TIME=n are still located in
hrtimer.c. Move them to time/timekeeping.c where they belong.
LKML-Reference: <new-submission>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The generic ktime_get function defined in kernel/hrtimer.c is suboptimial
for GENERIC_TIME=y:
0) | ktime_get() {
0) | ktime_get_ts() {
0) | getnstimeofday() {
0) | read_tod_clock() {
0) 0.601 us | }
0) 1.938 us | }
0) | set_normalized_timespec() {
0) 0.602 us | }
0) 4.375 us | }
0) 5.523 us | }
Overall there are two read_seqbegin/read_seqretry loops and a lot of
unnecessary struct timespec calculations. ktime_get returns a nano second
value which is the sum of xtime, wall_to_monotonic and the nano second
delta from the clock source.
ktime_get can be optimized for GENERIC_TIME=y. The new version only calls
clocksource_read:
0) | ktime_get() {
0) | read_tod_clock() {
0) 0.610 us | }
0) 1.977 us | }
It uses a single read_seqbegin/readseqretry loop and just adds everthing
to a nano second value.
ktime_get_ts is optimized in a similar fashion.
[ tglx: added WARN_ON(timekeeping_suspended) as in getnstimeofday() ]
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Acked-by: john stultz <johnstul@us.ibm.com>
LKML-Reference: <20090707112728.3005244d@skybase>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
When the kernel is configured with CONFIG_TIMER_STATS but timer
stats are runtime disabled we still get calls to
__timer_stats_timer_set_start_info which initializes some
fields in the corresponding struct timer_list.
So add some quick checks in the the timer stats setup functions
to avoid function calls to __timer_stats_timer_set_start_info
when timer stats are disabled.
In an artificial workload that does nothing but playing ping
pong with a single tcp packet via loopback this decreases cpu
consumption by 1 - 1.5%.
This is part of a modified function trace output on SLES11:
perl-2497 [00] 28630647177732388 [+ 125]: sk_reset_timer <-tcp_v4_rcv
perl-2497 [00] 28630647177732513 [+ 125]: mod_timer <-sk_reset_timer
perl-2497 [00] 28630647177732638 [+ 125]: __timer_stats_timer_set_start_info <-mod_timer
perl-2497 [00] 28630647177732763 [+ 125]: __mod_timer <-mod_timer
perl-2497 [00] 28630647177732888 [+ 125]: __timer_stats_timer_set_start_info <-__mod_timer
perl-2497 [00] 28630647177733013 [+ 93]: lock_timer_base <-__mod_timer
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Mustafa Mesanovic <mustafa.mesanovic@de.ibm.com>
Cc: Arjan van de Ven <arjan@infradead.org>
LKML-Reference: <20090623153811.GA4641@osiris.boeblingen.de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'timers-for-linus-migration' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
timers: Logic to move non pinned timers
timers: /proc/sys sysctl hook to enable timer migration
timers: Identifying the existing pinned timers
timers: Framework for identifying pinned timers
timers: allow deferrable timers for intervals tv2-tv5 to be deferred
Fix up conflicts in kernel/sched.c and kernel/timer.c manually
* 'timers-for-linus-clockevents' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clockevent: export register_device and delta2ns
clockevents: tick_broadcast_device can become static
* 'timers-for-linus-clocksource' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
clocksource: prevent selection of low resolution clocksourse also for nohz=on
clocksource: sanity check sysfs clocksource changes
commit 3f68535ada (clocksource: sanity check sysfs clocksource
changes) prevents selection of non high resolution capable
clocksources when high resolution mode is active, but did not take
into account that the same rules apply for highres=off nohz=on.
Check the tick device mode instead of hrtimer_hres_active() to verify
whether the system needs to be protected from a switch to jiffies or
other non highres capable clock sources.
Reported-by: Luming Yu <luming.yu@gmail.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Thomas, Andrew and Ingo pointed out that we don't have any safety checks
in the clocksource sysfs entries to make sure sysadmins don't try to
change the clocksource to a non high-res timer capable clocksource (such
as jiffies) when high-res timers (HRT) is enabled. Doing so will likely
hang a system.
Correct this by filtering non HRT clocksources from available_clocksources
and not accepting non HRT clocksources with HRT enabled.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
A call from irq_exit() may occasionally pause the timing
info for cpufreq ondemand governor. This results in the
cpufreq ondemand governor to fail to calculate the
system load properly. Thus, relocate the checks for this
particular case to keep the governor always functional.
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Reported-by: Tero Kristo <tero.kristo@nokia.com>
Acked-by: Rik van Riel <riel@redhat.com>
Acked-by: Venkatesh Pallipadi <venkatesh.pallipadi@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Dimitri Sivanich noticed that xtime_lock is held write locked across
calc_load() which iterates over all online CPUs. That can cause long
latencies for xtime_lock readers on large SMP systems.
The load average calculation is an rough estimate anyway so there is
no real need to protect the readers vs. the update. It's not a problem
when the avenrun array is updated while a reader copies the values.
Instead of iterating over all online CPUs let the scheduler_tick code
update the number of active tasks shortly before the avenrun update
happens. The avenrun update itself is handled by the CPU which calls
do_timer().
[ Impact: reduce xtime_lock write locked section ]
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Peter Zijlstra <peterz@infradead.org>
* Arun R Bharadwaj <arun@linux.vnet.ibm.com> [2009-04-16 12:11:36]:
This patch migrates all non pinned timers and hrtimers to the current
idle load balancer, from all the idle CPUs. Timers firing on busy CPUs
are not migrated.
While migrating hrtimers, care should be taken to check if migrating
a hrtimer would result in a latency or not. So we compare the expiry of the
hrtimer with the next timer interrupt on the target cpu and migrate the
hrtimer only if it expires *after* the next interrupt on the target cpu.
So, added a clockevents_get_next_event() helper function to return the
next_event on the target cpu's clock_event_device.
[ tglx: cleanups and simplifications ]
Signed-off-by: Arun R Bharadwaj <arun@linux.vnet.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
* Arun R Bharadwaj <arun@linux.vnet.ibm.com> [2009-04-16 12:11:36]:
The following pinned hrtimers have been identified and marked:
1)sched_rt_period_timer
2)tick_sched_timer
3)stack_trace_timer_fn
[ tglx: fixup the hrtimer pinned mode ]
Signed-off-by: Arun R Bharadwaj <arun@linux.vnet.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Export the following symbols using EXPORT_SYMBOL_GPL:
- clockevent_delta2ns
- clockevents_register_device
This allows us to build SuperH clockevent and clocksource
drivers as modules, see drivers/clocksource/sh_*.c
[ Impact: allow modular build of clockevent drivers ]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
LKML-Reference: <20090501055247.8286.64067.sendpatchset@rx1.opensource.se>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Some arches don't supply their own clocksource. This is mainly the
case in architectures that get their inter-tick times by reading the
counter on their interval timer. Since these timers wrap every tick,
they're not really useful as clocksources. Wrapping them to act like
one is possible but not very efficient. So we provide a callout these
arches can implement for use with the jiffies clocksource to provide
finer then tick granular time.
[ Impact: ease the migration to generic time keeping ]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Setup clocksource mult_orig in clocksource_enable().
Clocksource drivers can save power by using keeping the
device clock disabled while the clocksource is unused.
In practice this means that the enable() and disable()
callbacks perform clk_enable() and clk_disable().
The enable() callback may also use clk_get_rate() to get
the clock rate from the clock framework. This information
can then be used to calculate the shift and mult variables.
Currently the mult_orig variable is setup from mult at
registration time only. This is conflicting with the above
case since the clock is disabled and the mult variable is
not yet calculated at the time of registration.
Moving the mult_orig setup code to clocksource_enable()
allows us to both handle the common case with no enable()
callback and the mult-changed-after-enable() case.
[ Impact: allow dynamic clock source usage ]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
LKML-Reference: <20090501054546.8193.10688.sendpatchset@rx1.opensource.se>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The variable tick_broadcast_device is not used outside of the
file where it is defined, so let's make it static.
Signed-off-by: Dmitri Vorobiev <dmitri.vorobiev@movial.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
tick_handle_periodic() can lock up hard when a one shot clock event
device is used in combination with jiffies clocksource.
Avoid an endless loop issue by requiring that a highres valid
clocksource be installed before we call tick_periodic() in a loop when
using ONESHOT mode. The result is we will only increment jiffies once
per interrupt until a continuous hardware clocksource is available.
Without this, we can run into a endless loop, where each cycle through
the loop, jiffies is updated which increments time by tick_period or
more (due to clock steering), which can cause the event programming to
think the next event was before the newly incremented time and fail
causing tick_periodic() to be called again and the whole process loops
forever.
[ Impact: prevent hard lock up ]
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@kernel.org
Add enable() and disable() callbacks for clocksources.
This allows us to put unused clocksources in power save mode. The
functions clocksource_enable() and clocksource_disable() wrap the
callbacks and are inserted in the timekeeping code to enable before use
and disable after switching to a new clocksource.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Pass clocksource pointer to the read() callback for clocksources. This
allows us to share the callback between multiple instances.
[hugh@veritas.com: fix powerpc build of clocksource pass clocksource mods]
[akpm@linux-foundation.org: cleanup]
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Acked-by: John Stultz <johnstul@us.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Hugh Dickins <hugh@veritas.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
The time_status conditional was accidentally placed right after we clear
the checked time_status bits, which causes us to take the conditional
every time through. This fixes it by moving the conditional to before we
clear the time_status bits.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Cc: Clark Williams <williams@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, no functionality changed
The 'time_adj' local variable is named in a very confusing
way because it almost shadows the 'time_adjust' global
variable - which is used in this same function.
Rename it to 'delta' - to make them stand apart more clearly.
kernel/time/ntp.o:
text data bss dec hex filename
2545 114 144 2803 af3 ntp.o.before
2545 114 144 2803 af3 ntp.o.after
md5:
1bf0b3be564512279ba7cee299d1d2be ntp.o.before.asm
1bf0b3be564512279ba7cee299d1d2be ntp.o.after.asm
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: micro-optimization
Convert the (internal) ntp_tick_adj value we store from unscaled
units to scaled units. This is a constant that we never modify,
so scaling it up once during bootup is enough - we dont have to
do it for every adjustment step.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, no functionality changed
Further simplify do_adjtimex():
- introduce the ntp_start_leap_timer() helper function
- eliminate the goto adj_done complication
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, no functionality changed
do_adjtimex() is currently a monster function with a maze of
branches. Refactor the txc->modes setting aspects of it into
two new helper functions:
process_adj_status()
process_adjtimex_modes()
kernel/time/ntp.o:
text data bss dec hex filename
2512 114 136 2762 aca ntp.o.before
2512 114 136 2762 aca ntp.o.after
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: change (fix) the way the NTP PLL seconds offset is initialized/tracked
Fix a bug and do a micro-optimization:
When PLL is enabled we do not reset time_reftime. If the PLL
was off for a long time (for example after bootup), this is
arguably the wrong thing to do.
We already had a hack for the common boot-time case in
ntp_update_offset(), in form of:
if (unlikely(time_status & STA_FREQHOLD || time_reftime == 0))
secs = 0;
But the update delta should be reset later on too - not just when
the PLL is enabled for the first time after bootup.
So do it on !STA_PLL -> STA_PLL transitions.
This changes behavior, as previously if ntpd was disabled for
a long time and we restarted it, we'd run from that last update,
with a very large delta.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, no functionality changed
The time_reftime update in ntp_update_offset() to xtime.tv_sec
is a convoluted way of saying that we want to freeze the frequency
and want the 'secs' delta to be 0. Also make this branch unlikely.
This shaves off 8 bytes from the code size:
text data bss dec hex filename
2504 114 136 2754 ac2 ntp.o.before
2496 114 136 2746 aba ntp.o.after
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, no functionality changed
Change ntp_update_offset_fll() to delta logic instead of
absolute value logic. This eliminates 'freq_adj' from the
function.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, no functionality changed
Change ntp_update_frequency() from a hard to follow code
flow that uses global variables as temporaries, to a clean
input+output flow.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, no functionality changed
There's an ugly u64 typecase in the MAX_TICKADJ_SCALED definition,
this can be eliminated by making the MAX_TICKADJ constant's type
64-bit (signed).
kernel/time/ntp.o:
text data bss dec hex filename
2504 114 136 2754 ac2 ntp.o.before
2504 114 136 2754 ac2 ntp.o.after
md5:
41f3009debc9b397d7394dd77d912f0a ntp.o.before.asm
41f3009debc9b397d7394dd77d912f0a ntp.o.after.asm
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, no functionality changed
Instead of a hierarchy of conditions, transform them to clean
gradual conditions and return's.
This makes the flow easier to read and makes the purpose of
the function easier to understand.
kernel/time/ntp.o:
text data bss dec hex filename
2552 170 168 2890 b4a ntp.o.before
2552 170 168 2890 b4a ntp.o.after
md5:
eae1275df0b7d6290c13f6f6f8f05c8c ntp.o.before.asm
eae1275df0b7d6290c13f6f6f8f05c8c ntp.o.after.asm
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, no functionality changed
Make this file a bit more readable by applying a consistent coding style.
No code changed:
kernel/time/ntp.o:
text data bss dec hex filename
2552 170 168 2890 b4a ntp.o.before
2552 170 168 2890 b4a ntp.o.after
md5:
eae1275df0b7d6290c13f6f6f8f05c8c ntp.o.before.asm
eae1275df0b7d6290c13f6f6f8f05c8c ntp.o.after.asm
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Since the GENERIC_TIME changes landed, the adjtimex behavior changed
for struct timex.tick and .freq changed. When the tick or freq value
is set, we adjust the tick_length_base in ntp_update_frequency().
However, this new value doesn't get applied to tick_length until the
next second (via second_overflow).
This means some applications that do quick time tweaking do not see the
requested change made as quickly as expected.
I've run a few tests with this change, and ntpd still functions fine.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Mapping from a struct timecounter to a time returned by functions like
ktime_get_real() is implemented. This is sufficient to use this code
in a network device driver which wants to support hardware time
stamping and transformation of hardware time stamps to system time.
The interface could have been made more versatile by not depending on
a time counter, but this wasn't done to avoid writing glue code
elsewhere.
The method implemented here is the one used and analyzed under the name
"assisted PTP" in the LCI PTP paper:
http://www.linuxclustersinstitute.org/conferences/archive/2008/PDF/Ohly_92221.pdf
Acked-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So far struct clocksource acted as the interface between time/timekeeping.c
and hardware. This patch generalizes the concept so that a similar
interface can also be used in other contexts. For that it introduces
new structures and related functions *without* touching the existing
struct clocksource.
The reasons for adding these new structures to clocksource.[ch] are
* the APIs are clearly related
* struct clocksource could be cleaned up to use the new structs
* avoids proliferation of files with similar names (timesource.h?
timecounter.h?)
As outlined in the discussion with John Stultz, this patch adds
* struct cyclecounter: stateless API to hardware which counts clock cycles
* struct timecounter: stateful utility code built on a cyclecounter which
provides a nanosecond counter
* only the function to read the nanosecond counter; deltas are used internally
and not exposed to users of timecounter
The code does no locking of the shared state. It must be called at least
as often as the cycle counter wraps around to detect these wrap arounds.
Both is the responsibility of the timecounter user.
Acked-by: John Stultz <johnstul@us.ibm.com>
Signed-off-by: Patrick Ohly <patrick.ohly@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Impact: fix CPU hotplug hang on Power6 testbox
On architectures that support offlining all cpus (at least powerpc/pseries),
hot-unpluging the tick_do_timer_cpu can result in a system hang.
This comes from the fact that if the cpu going down happens to be the
cpu doing the tick, then as the tick_do_timer_cpu handover happens after the
cpu is dead (via the CPU_DEAD notification), we're left without ticks,
jiffies are frozen and any task relying on timers (msleep, ...) is stuck.
That's particularly the case for the cpu looping in __cpu_die() waiting
for the dying cpu to be dead.
This patch addresses this by having the tick_do_timer_cpu handover happen
earlier during the CPU_DYING notification. For this, a new clockevent
notification type is introduced (CLOCK_EVT_NOTIFY_CPU_DYING) which is triggered
in hrtimer_cpu_notify().
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Allow the set_mode() clockevent callback to decide and fill in delta
details such as shift, mult, max_delta_ns and min_delta_ns.
With this change the clockevent can be registered without delta details
which allows us to keep the parent clock disabled until the clockevent
gets setup using set_mode().
Letting set_mode() fill in or update delta details allows us to save
power by disabling the parent clock while the clockevent is unused.
This may however make the parent clock rate change, so next time the
clockevent gets enabled we need let set_mode() to update the detla
details accordingly. Doing it at registration time is not enough.
Furthermore, the delta details seem unused in the case of periodic-only
clockevent drivers, so this change also allows registration of such
drivers without the delta details filled in.
Signed-off-by: Magnus Damm <damm@igel.co.jp>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: cleanup, reduce kernel size a bit, avoid sparse warning
Fixes sparse warning:
kernel/time/tick-sched.c:137:6: warning: symbol 'tick_nohz_update_jiffies' was not declared. Should it be static?
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (24 commits)
trivial: chack -> check typo fix in main Makefile
trivial: Add a space (and a comma) to a printk in 8250 driver
trivial: Fix misspelling of "firmware" in docs for ncr53c8xx/sym53c8xx
trivial: Fix misspelling of "firmware" in powerpc Makefile
trivial: Fix misspelling of "firmware" in usb.c
trivial: Fix misspelling of "firmware" in qla1280.c
trivial: Fix misspelling of "firmware" in a100u2w.c
trivial: Fix misspelling of "firmware" in megaraid.c
trivial: Fix misspelling of "firmware" in ql4_mbx.c
trivial: Fix misspelling of "firmware" in acpi_memhotplug.c
trivial: Fix misspelling of "firmware" in ipw2100.c
trivial: Fix misspelling of "firmware" in atmel.c
trivial: Fix misspelled firmware in Kconfig
trivial: fix an -> a typos in documentation and comments
trivial: fix then -> than typos in comments and documentation
trivial: update Jesper Juhl CREDITS entry with new email
trivial: fix singal -> signal typo
trivial: Fix incorrect use of "loose" in event.c
trivial: printk: fix indentation of new_text_line declaration
trivial: rtc-stk17ta8: fix sparse warning
...
* 'cpus4096-for-linus-3' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (77 commits)
x86: setup_per_cpu_areas() cleanup
cpumask: fix compile error when CONFIG_NR_CPUS is not defined
cpumask: use alloc_cpumask_var_node where appropriate
cpumask: convert shared_cpu_map in acpi_processor* structs to cpumask_var_t
x86: use cpumask_var_t in acpi/boot.c
x86: cleanup some remaining usages of NR_CPUS where s/b nr_cpu_ids
sched: put back some stack hog changes that were undone in kernel/sched.c
x86: enable cpus display of kernel_max and offlined cpus
ia64: cpumask fix for is_affinity_mask_valid()
cpumask: convert RCU implementations, fix
xtensa: define __fls
mn10300: define __fls
m32r: define __fls
h8300: define __fls
frv: define __fls
cris: define __fls
cpumask: CONFIG_DISABLE_OBSOLETE_CPUMASK_FUNCTIONS
cpumask: zero extra bits in alloc_cpumask_var_node
cpumask: replace for_each_cpu_mask_nr with for_each_cpu in kernel/time/
cpumask: convert mm/
...
* 'cpus4096-for-linus-2' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (66 commits)
x86: export vector_used_by_percpu_irq
x86: use logical apicid in x2apic_cluster's x2apic_cpu_mask_to_apicid_and()
sched: nominate preferred wakeup cpu, fix
x86: fix lguest used_vectors breakage, -v2
x86: fix warning in arch/x86/kernel/io_apic.c
sched: fix warning in kernel/sched.c
sched: move test_sd_parent() to an SMP section of sched.h
sched: add SD_BALANCE_NEWIDLE at MC and CPU level for sched_mc>0
sched: activate active load balancing in new idle cpus
sched: bias task wakeups to preferred semi-idle packages
sched: nominate preferred wakeup cpu
sched: favour lower logical cpu number for sched_mc balance
sched: framework for sched_mc/smt_power_savings=N
sched: convert BALANCE_FOR_xx_POWER to inline functions
x86: use possible_cpus=NUM to extend the possible cpus allowed
x86: fix cpu_mask_to_apicid_and to include cpu_online_mask
x86: update io_apic.c to the new cpumask code
x86: Introduce topology_core_cpumask()/topology_thread_cpumask()
x86: xen: use smp_call_function_many()
x86: use work_on_cpu in x86/kernel/cpu/mcheck/mce_amd_64.c
...
Fixed up trivial conflict in kernel/time/tick-sched.c manually
Impact: cleanup
Simple replacement, now the _nr is redundant.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Cc: Ingo Molnar <mingo@redhat.com>
Impact: Use new APIs
Convert kernel/time functions to use struct cpumask *.
Note the ugly bitmap declarations in tick-broadcast.c. These should
be cpumask_var_t, but there was no obvious initialization function to
put the alloc_cpumask_var() calls in. This was safe.
(Eventually 'struct cpumask' will be undefined for CONFIG_CPUMASK_OFFSTACK,
so we use a bitmap here to show we really mean it).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
The cpu time spent by the idle process actually doing something is
currently accounted as idle time. This is plain wrong, the architectures
that support VIRT_CPU_ACCOUNTING=y can do better: distinguish between the
time spent doing nothing and the time spent by idle doing work. The first
is accounted with account_idle_time and the second with account_system_time.
The architectures that use the account_xxx_time interface directly and not
the account_xxx_ticks interface now need to do the check for the idle
process in their arch code. In particular to improve the system vs true
idle time accounting the arch code needs to measure the true idle time
instead of just testing for the idle process.
To improve the tick based accounting as well we would need an architecture
primitive that can tell us if the pt_regs of the interrupted context
points to the magic instruction that halts the cpu.
In addition idle time is no more added to the stime of the idle process.
This field now contains the system time of the idle process as it should
be. On systems without VIRT_CPU_ACCOUNTING this will always be zero as
every tick that occurs while idle is running will be accounted as idle
time.
This patch contains the necessary common code changes to be able to
distinguish idle system time and true idle time. The architectures with
support for VIRT_CPU_ACCOUNTING need some changes to exploit this.
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
The utimescaled / stimescaled fields in the task structure and the
global cpustat should be set on all architectures. On s390 the calls
to account_user_time_scaled and account_system_time_scaled never have
been added. In addition system time that is accounted as guest time
to the user time of a process is accounted to the scaled system time
instead of the scaled user time.
To fix the bugs and to prevent future forgetfulness this patch merges
account_system_time_scaled into account_system_time and
account_user_time_scaled into account_user_time.
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Jeremy Fitzhardinge <jeremy@xensource.com>
Cc: Chris Wright <chrisw@sous-sol.org>
Cc: Michael Neuling <mikey@neuling.org>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Redo:
5b7dba4: sched_clock: prevent scd->clock from moving backwards
which had to be reverted due to s2ram hangs:
ca7e716: Revert "sched_clock: prevent scd->clock from moving backwards"
... this time with resume restoring GTOD later in the sequence
taken into account as well.
The "timekeeping_suspended" flag is not very nice but we cannot call into
GTOD before it has been properly resumed and the scheduler will run very
early in the resume sequence.
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix CPU hotplug hang on Power6 testbox
On architectures that support offlining all cpus (at least powerpc/pseries),
hot-unpluging the tick_do_timer_cpu can result in a system hang.
This comes from the fact that if the cpu going down happens to be the
cpu doing the tick, then as the tick_do_timer_cpu handover happens after the
cpu is dead (via the CPU_DEAD notification), we're left without ticks,
jiffies are frozen and any task relying on timers (msleep, ...) is stuck.
That's particularly the case for the cpu looping in __cpu_die() waiting
for the dying cpu to be dead.
This patch addresses this by having the tick_do_timer_cpu handover happen
earlier during the CPU_DYING notification. For this, a new clockevent
notification type is introduced (CLOCK_EVT_NOTIFY_CPU_DYING) which is triggered
in hrtimer_cpu_notify().
Signed-off-by: Sebastien Dugue <sebastien.dugue@bull.net>
Cc: <stable@kernel.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: change calling convention of existing clock_event APIs
struct clock_event_timer's cpumask field gets changed to take pointer,
as does the ->broadcast function.
Another single-patch change. For safety, we BUG_ON() in
clockevents_register_device() if it's not set.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Ingo Molnar <mingo@elte.hu>
Impact: change existing irq_chip API
Not much point with gentle transition here: the struct irq_chip's
setaffinity method signature needs to change.
Fortunately, not widely used code, but hits a few architectures.
Note: In irq_select_affinity() I save a temporary in by mangling
irq_desc[irq].affinity directly. Ingo, does this break anything?
(Folded in fix from KOSAKI Motohiro)
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Mike Travis <travis@sgi.com>
Reviewed-by: Grant Grundler <grundler@parisc-linux.org>
Acked-by: Ingo Molnar <mingo@redhat.com>
Cc: ralf@linux-mips.org
Cc: grundler@parisc-linux.org
Cc: jeremy@xensource.com
Cc: KOSAKI Motohiro <kosaki.motohiro@jp.fujitsu.com>
In my device I get many interrupts from a high speed USB device in a very
short period of time. The system spends a lot of time reprogramming the
hardware timer which is in a slower timing domain as compared to the CPU.
This results in the CPU spending a huge amount of time waiting for the
timer posting to be done. All of this reprogramming is useless as the
wake up time has not changed.
As measured using ETM trace this drops my reprogramming penalty from
almost 60% CPU load down to 15% during high interrupt rate. I can send
traces to show this.
Suppress setting of duplicate timer event when timer already stopped.
Timer programming can be very costly and can result in long cpu stall/wait
times.
[akpm@linux-foundation.org: coding-style fixes]
[tglx@linutronix.de: move the check to the right place and avoid raising
the softirq for nothing]
Signed-off-by: Richard Woodruff <r-woodruff2@ti.com>
Cc: johnstul@us.ibm.com
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Impact: remove false positive warning
After a cpu was taken down during cpu hotplug (read: disabled for interrupts)
it still might have pending softirqs. However take_cpu_down makes sure
that the idle task will run next instead of ksoftirqd on the taken down cpu.
The idle task will call tick_nohz_stop_sched_tick which might warn about
pending softirqs just before the cpu kills itself completely.
However the pending softirqs on the dead cpu aren't a problem because they
will be moved to an online cpu during CPU_DEAD handling.
So make sure we warn only for online cpus.
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: fix time warp bug
Alex Shi, along with Yanmin Zhang have been noticing occasional time
inconsistencies recently. Through their great diagnosis, they found that
the xtime_nsec value used in update_wall_time was occasionally going
negative. After looking through the code for awhile, I realized we have
the possibility for an underflow when three conditions are met in
update_wall_time():
1) We have accumulated a second's worth of nanoseconds, so we
incremented xtime.tv_sec and appropriately decrement xtime_nsec.
(This doesn't cause xtime_nsec to go negative, but it can cause it
to be small).
2) The remaining offset value is large, but just slightly less then
cycle_interval.
3) clocksource_adjust() is speeding up the clock, causing a
corrective amount (compensating for the increase in the multiplier
being multiplied against the unaccumulated offset value) to be
subtracted from xtime_nsec.
This can cause xtime_nsec to underflow.
Unfortunately, since we notify the NTP subsystem via second_overflow()
whenever we accumulate a full second, and this effects the error
accumulation that has already occured, we cannot simply revert the
accumulated second from xtime nor move the second accumulation to after
the clocksource_adjust call without a change in behavior.
This leaves us with (at least) two options:
1) Simply return from clocksource_adjust() without making a change if we
notice the adjustment would cause xtime_nsec to go negative.
This would work, but I'm concerned that if a large adjustment was needed
(due to the error being large), it may be possible to get stuck with an
ever increasing error that becomes too large to correct (since it may
always force xtime_nsec negative). This may just be paranoia on my part.
2) Catch xtime_nsec if it is negative, then add back the amount its
negative to both xtime_nsec and the error.
This second method is consistent with how we've handled earlier rounding
issues, and also has the benefit that the error being added is always in
the oposite direction also always equal or smaller then the correction
being applied. So the risk of a corner case where things get out of
control is lessened.
This patch fixes bug 11970, as tested by Yanmin Zhang
http://bugzilla.kernel.org/show_bug.cgi?id=11970
Reported-by: alex.shi@intel.com
Signed-off-by: John Stultz <johnstul@us.ibm.com>
Acked-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Tested-by: "Zhang, Yanmin" <yanmin_zhang@linux.intel.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: cleanup, move all hrtimer processing into hardirq context
This is an attempt at removing some of the hrtimer complexity by
reducing the number of callback modes to 1.
This means that all hrtimer callback functions will be ran from HARD-irq
context.
I went through all the 30 odd hrtimer callback functions in the kernel
and saw only one that I'm not quite sure of, which is the one in
net/can/bcm.c - hence I'm CC-ing the folks responsible for that code.
Furthermore, the hrtimer core now calls callbacks directly with IRQs
disabled in case you try to enqueue an expired timer. If this timer is a
periodic timer (which should use hrtimer_forward() to advance its time)
then it might be possible to end up in an inf. recursive loop due to the
fact that hrtimer_forward() doesn't round up to the next timer
granularity, and therefore keeps on calling the callback - obviously
this needs a fix.
Aside from that, this seems to compile and actually boot on my dual core
test box - although I'm sure there are some bugs in, me not hitting any
makes me certain :-)
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: (future) size reduction for large NR_CPUS.
Dynamically allocating cpumasks (when CONFIG_CPUMASK_OFFSTACK) saves
space for small nr_cpu_ids but big CONFIG_NR_CPUS. cpumask_var_t
is just a struct cpumask for !CONFIG_CPUMASK_OFFSTACK.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Impact: nohz powersavings and wakeup regression
commit fb02fbc14d (NOHZ: restart tick
device from irq_enter()) causes a serious wakeup regression.
While the patch is correct it does not take into account that spurious
wakeups happen on x86. A fix for this issue is available, but we just
revert to the .27 behaviour and let long running softirqs screw
themself.
Disable it for now.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
commit fb02fbc14d (NOHZ: restart tick
device from irq_enter())
solves the problem of stale jiffies when long running softirqs happen
in a long idle sleep period, but it has a major thinko in it:
When the interrupt which came in _is_ the timer interrupt which should
expire ts->sched_timer then we cancel and rearm the timer _before_ it
gets expired in hrtimer_interrupt() to the next period. That means the
call back function is not called. This game can go on for ever :(
Prevent this by making sure to only rearm the timer when the expiry
time is more than one tick_period away. Otherwise keep it running as
it is either already expired or will expiry at the right point to
update jiffies.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Venkatesch Pallipadi <venkatesh.pallipadi@intel.com>
The base address of a (per cpu) clock base is a useful debug info.
Add it and bump the version number of timer_lists.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The per cpu clock events device output of timer_list lacks an
association of the device to the cpu which is annoying when looking at
the output of /proc/timer_list from a 128 way system.
Add the CPU number info and mark the broadcast device in the device
list printout.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
The current timer_list output prints the address of the on stack copy
of the active hrtimer instead of the hrtimer itself.
Print the address of the real timer instead.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
We did not restart the tick device from irq_enter() to avoid double
reprogramming and extra events in the return immediate to idle case.
But long lasting softirqs can lead to a situation where jiffies become
stale:
idle()
tick stopped (reprogrammed to next pending timer)
halt()
interrupt
jiffies updated from irq_enter()
interrupt handler
softirq function 1 runs 20ms
softirq function 2 arms a 10ms timer with a stale jiffies value
jiffies updated from irq_exit()
timer wheel has now an already expired timer
(the one added in function 2)
timer fires and timer softirq runs
This was discovered when debugging a timer problem which happend only
when the ath5k driver is active. The debugging proved that there is a
softirq function running for more than 20ms, which is a bug by itself.
To solve this we restart the tick timer right from irq_enter(), but do
not go through the other functions which are necessary to return from
idle when need_resched() is set.
Reported-by: Elias Oltmanns <eo@nebensachen.de>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Elias Oltmanns <eo@nebensachen.de>
We have two separate nohz function calls in irq_enter() for no good
reason. Just call a single NOHZ function from irq_enter() and call
the bits in the tick code.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
John Stultz