Convert to module_platform_driver() to simplify code.
Signed-off-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
'reg_context' is local to this file. Make it static.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Use the wrapper function for retrieving the platform data instead of
accessing dev->platform_data directly. This is a cosmetic change
to make the code simpler and enhance the readability.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The polarities were being set to active low when fbdev was requesting active
high. This patch reverses it so that what is set into the LCD controller is
correct.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
TI LCD controller version 2 adds some extra bits in a register to
increase the available size to represent horizontal timings. This
patch allows the fbdev driver to utilize those extra bits.
This will become important for driving an HDMI encoder from the lcd
controller where some of the VESA/CEA modes require quite large porches.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The LCD controller represents some of the timing fields with a 0
in the register representing 1. This was not taken into account
when these registers were being set. Interestingly enough not
all of the LCDC controller timing registers implement this representation
so carefully went through the technical reference manual to only "fix"
the correct timings.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The driver was mapping the wrong fbdev margins to the
front porch / back porch for both vertical and horizontal
timings.
This patch corrects it so that:
hfp = right margin
hbp = left margin
vbp = upper margin
vfp = lower margin
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Remove use of explicit inline compiler directive and let the compiler
make the decision as per Documentation/CodingStyle.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Clean up the code, so that the names of the various clock variables
are consistent to it is clear what variable is associated with what
clock.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Based on original patch by: Afzal Mohammed <afzal@ti.com>
LCDC IP has a clock divider to adjust pixel clock, this limits pixel
clock range to fck/255 - fck/2(fck - rate of input clock to LCDC IP).
In the case of AM335x, where this IP is present, default fck is not
sufficient to provide normal pixel clock rates, hence rendering this
driver unusable on AM335x.
If input clock too is configurable, allowable range of pixel clock
would increase. Here initially it is checked whether with present fck,
divider in IP could be configured to obtain required rate, if not,
fck is adjusted. This makes it usable on AM335x.
Note:
Another solution would be to model an inherited basic clock divider of
CCF, an advantage would be a better possible resolution for pixel clk.
And trying to instantiate a CCF clock would mean that to be consistent,
3 bits being turned on to enable clocks of LCDC IP would have to be
modeled as gate clocks. Now that would bring in a total of 4 clocks,
including necessity to create a new inherited divider clock, and that
mean a branch of clock tree would be present in LCDC driver. This
would add complexity to LCDC driver bringing in considerable amount
of clock handling code, and this would not bring in much advantage
for existing use cases other than providing a higher resolution of
pixel clock. And existing use cases work without relying on clock
modeling. Another fact is that out of the two platform's using this
driver DaVinci is not yet converted to CCF. In future if higher
resolution of pixel clock is required, and probably after DaVinci is
CCF'ed, modeling clock nodes inside driver may be considered.
v2: purely cosmetic changes to try and clarify what variables are
being used for in the clock rate / divider calculations
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Move panel detection to a separate function, this helps in readability
as well as makes DT support cleaner.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Ensure that platform data contains pointer for lcd_ctrl_config.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Replace existing resource handling in the driver with managed device
resource.
v2: implement some changes as recommended by
Prabhakar Lad <prabhakar.csengg@gmail.com>
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
The interrupt handler explicitly has code that handles the sync lost
interrupt. However the sync lost interrupt is never actually being
enabled in the LCD controller, therefore this interrupt code path is not
being exercised. This fix simply enables the generation of the sync
lost interrupt by the LCD controller so it can be dealt with
appropriately by the interrupt handler.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Based on original patch by: Manjunathappa, Prakash <prakash.pm@ti.com>
and Afzal Mohammed <afzal@ti.com>
Set only LCD_V2_TFT_24BPP_MODE bit for 24bpp and LCD_V2_TFT_24BPP_UNPACK
bit along with LCD_V2_TFT_24BPP_MODE for 32bpp configuration.
Patch is tested on am335x-evm for 24bpp and da850-evm for 16bpp
configurations.
v2: removes confusing fall through in case statement for pixel
depth configuration.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Change the lcd_disable_raster funtion from using a bool to an enum
as the function is very confusing with the current api. This helps
make it clearer what the parameter is really doing.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
v1: original from Afzal Mohammed <afzal@ti.com>
fb_set_par helps in runtime configuration of lcd controller like
changing resolution, pixel clock etc. (eg. using fbset utility)
Reconfigure lcd controller based on information passed by framework.
Enable raster back if it was already enabled.
As fb_set_par would get invoked indirectly from probe via fb_set_var,
remove existing lcdc initialization in probe and do lcdc reset in
probe so that reset happens only at the begining.
v2: changes from Darren Etheridge <detheridge@ti.com>
remove unnecessary conditional branch where we attempt to disable
something that we already checked to see if it was disabled.
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Update "var" pixclock with the value that is configurable in hardware.
This lets user know the actual pixclock.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
store struct device pointer so that dev_dbg/err can be used outside
of probe.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Based on original patch by: Afzal Mohammed <afzal@ti.com>
Use the new modedb field to store pix clk. Reorganize existing clock
divider functions with names now corresponding to what they do, add
common function prefix.
Fix existing panel modedb pixclock to be in ps instead of Hz. This
needed a change in the way clock divider is calculated. As modedb
pixclock information is now in ps, override on "var" pixclock over
modedb to var conversion is removed.
v2:
Changed pixel clock configuration to use KHZ2PICOS macro
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
store lcd clk rate always, i.e. irrespective of whether CPUFREQ is
enabled or not. This can be used to get clk rate directly instead of
enquiring with clock framework with clk handle every time.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
store current videomode and controller data so that reconfiguring can
be done easily. Reconfiguring would be required in fb_set_par, which
is going to be added soon.
If these details are not stored, the work probe does to retrieve these
information would have to repeated at the place of reconfiguring and
modifying platform data would be necessary to handle controller data
changes like bpp.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
modedb helper now updates "var" information based on the detected
panel, remove the unnecessary initialization.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
modedb structure is now used to store panel information, run modedb
helper over it for initial update of "var" information instead of
equating each fields.
While at it, remove redundant update of bits_per_pixel.
Note: pixclock is overridden with proper value using an existing code
as currently modedb is having it in Hz instead of ps, this would be
fixed in a later change and this overide would be removed.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
lcd_reset function doesn't require any arguement, remove it.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Check whether "struct fb_var_screeninfo" fields are sane, if not
update it to be within allowed limits.
If user sends down buggy "var" values, this will bring those within
allowable limits. And fb_set_par is not supposed to change "var"
values, fb_check_var has to ensure that values are proper.
Signed-off-by: Afzal Mohammed <afzal@ti.com>
Signed-off-by: Darren Etheridge <detheridge@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
CONFIG_HOTPLUG is going away as an option. As a result, the __dev*
markings need to be removed.
This change removes the use of __devinit, __devexit_p, __devinitdata,
__devinitconst, and __devexit from these drivers.
Based on patches originally written by Bill Pemberton, but redone by me
in order to handle some of the coding style issues better, by hand.
Cc: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The revision check fails for the beaglebone; Add new revision ID.
Signed-off-by: Pantelis Antoniou <panto@antoniou-consulting.com>
Acked-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
do clk_get on connection id "fck" to support OMAP based
platforms having multiple clocks for module. Without this
driver change clk_get fails on am335x.
This patch is based on the discussion in community
http://marc.info/?l=linux-kernel&m=135166018907827&w=2
Signed-off-by: Manjunathappa <prakash.pm@ti.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Acked-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Configure below LCDC configurations to optimal values, also have an
option configure these optional parameters for platform.
1) AC bias configuration: Required only for passive panels
2) Dma_burst_size:
3) FIFO_DMA_DELAY:
4) FIFO threshold: Does not apply for da830 LCDC.
Patch is verified for 16bpp and 24bpp configurations on da830, da850 and
am335x EVMs.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Adopt fb_videomode data instead of defining driver private
structure to hold panel information. This is the way standard FB
drivers maintain the panel information.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
It includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.12 (GNU/Linux)
iQIcBAABAgAGBQJQdz+EAAoJECSVL5KnPj1PyiMP/R84rSfGUbDIh0Cr6g1Snk76
h2/1i19TuEgJAWH1q0lnwhqMC3yYmkA1Hz3ulT35KS+/L3IEgUosOESrxZIJhxHI
f55pk3v8dueN0rx3OhCknLT7hGpVsI4vSN+3yf9LetDp3qt8UVwKLFzVij1VF/MS
b1wA+RBe1IYMR0bB6pK0AgMZZiBkQMta5rKs5IfDDi8kMgMT4+V8l/iFmt2Ue833
VxdPw+3reKshBXKTkQt1Usv4JRtG7OgwpRmFhxOo+ag0dxPLeUe/3wZG54qfOywF
7jK+mnxmW8oZxLkGBvygrmzd40MH6H09N7i/IKVQ0GZoHgAqWWe7VvWahpg8LzwB
ynktwWZ3Va98p5u/BIafBr0ZOU30mPL8N0aqR3HU7H12Wq21HtwcF+ewiT4vnMc8
CKzt6VL0qY1tOOdzJzmICzvXGkbBGfj9YOUptJALCIa3bLwZodyQ/bKq8V/bHdTg
2yyUmVhVf/r5qLermjQN8TjFMpRf2SNwTUUYvhUNwZ4yZMVWZgjjhtAlGGFCA/Bs
qMRuNpbHMedhzNV4py418Xe3Hwg6TLPuWSWGJ67SG8hxsYy2hq7GebSsXXdC7xG9
N5DMpA88IQR2nLwkr/pslFqjRsUI6ULvIfxibHEoNjQ0GOY9f+hEWbdHBZPI+0Gv
Ea9d7nyhmYTZgvRcd9U0
=EJUS
-----END PGP SIGNATURE-----
Merge tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6
Pull fbdev updates from Florian Tobias Schandinat:
"This includes:
- large updates for OMAP
- basic OMAP5 DSS support for DPI and DSI outputs
- large cleanups and restructuring
- some update to Exynos and da8xx-fb
- removal of the pnx4008 driver (arch removed)
- various other small patches"
Fix up some trivial conflicts (mostly just include line changes, but
also some due to the renaming of the deferred work functions by Tejun).
* tag 'fbdev-updates-for-3.7' of git://github.com/schandinat/linux-2.6: (193 commits)
gbefb: fix compile error
video: mark nuc900fb_map_video_memory as __devinit
video/mx3fb: set .owner to prevent module unloading while being used
video: exynos_dp: use clk_prepare_enable and clk_disable_unprepare
drivers/video/exynos/exynos_mipi_dsi.c: fix error return code
drivers/video/savage/savagefb_driver.c: fix error return code
video: s3c-fb: use clk_prepare_enable and clk_disable_unprepare
da8xx-fb: save and restore LCDC context across suspend/resume cycle
da8xx-fb: add pm_runtime support
video/udlfb: fix line counting in fb_write
OMAPDSS: add missing include for string.h
OMAPDSS: DISPC: Configure color conversion coefficients for writeback
OMAPDSS: DISPC: Add manager like functions for writeback
OMAPDSS: DISPC: Configure writeback FIFOs
OMAPDSS: DISPC: Configure writeback specific parameters in dispc_wb_setup()
OMAPDSS: DISPC: Configure overlay-like parameters in dispc_wb_setup
OMAPDSS: DISPC: Add function to set channel in for writeback
OMAPDSS: DISPC: Don't set chroma resampling bit for writeback
OMAPDSS: DISPC: Downscale chroma if plane is writeback
OMAPDSS: DISPC: Configure input and output sizes for writeback
...
Save and restore register context of LCDC respectively
before suspend and after resume.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
It is expected that LCDC to continue to be disabled after
resume if it is blanked before suspend. This is also true
for DVFS. But it is observed that LCDC being enabled after
suspend/resume cycle or DVFS.
Correcting it by having check for FB_BLANK_UNBLANK before
enabling.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Wait for active frame transfer to complete after disabling LCDC.
At the same this wait is not be required when there are sync and
underflow errors.
Patch applies for revision 2 of LCDC present am335x.
More information on disable and reset sequence can be found in
section 13.4.6 of AM335x TRM @www.ti.com/am335x.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
ARM is moving to stricter checks on readl/write functions,
so we need to use the correct types everywhere.
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: linux-fbdev@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
LCD controller on am335x supports 24bpp raster configuration in addition
to ones on da850. LCDC also supports 24bpp in unpacked format having
ARGB:8888 32bpp format data in DDR, but it doesn't interpret alpha
component of the data.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
LCD blink is observed during suspend/resume and blank/unblank
operations as backlight is ON during LCDC disable and enable.
So make sure to turn OFF backlight before disabling and turn
it ON after enabling.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
As in specification software reset should be applied for several
cycles before bringing it out of reset. Without this patch
particularly during suspend and resume clock reset is not guaranteed
to happen.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Patch works around the below silicon errata:
During LCDC initialization, there is the potential for a FIFO
underflow condition to occur. A FIFO underflow condition
occurs when the input FIFO is completely empty and the LCDC
raster controller logic that drives data to the output pins
attempts to fetch data from the FIFO. When a FIFO underflow
condition occurs, incorrect data will be driven out on the
LCDC data pins.
Software should poll the FUF bit field in the LCD_STAT register
to check if an error condition has occurred or service the
interrupt if FUF_EN is enabled when FUF occurs. If the FUF bit
field has been set to 1, this will indicate an underflow
condition has occurred and then the software should execute a
reset of the LCDC via the LPSC.
This problem may occur if the LCDC FIFO threshold size
(LCDDMA_CTRL[TH_FIFO_READY]) is left at its default value after
reset. Increasing the FIFO threshold size will reduce or
eliminate underflows. Setting the threshold size to 256 double
words or larger is recommended.
Above issue is described in section 2.1.3 of silicon errata
http://www.ti.com/lit/er/sprz313e/sprz313e.pdf
Signed-off-by: Rajashekhara, Sudhakar <sudhakar.raj@ti.com>
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Flicker/tearing effect is observed with current FB driver.
Issue is because of 2 active DMA channels ping ponging among them
along with usage of 2 DDR ping pong buffers in driver. Application
unaware of active DMA channel keeps updating frame being displayed,
this leads to tearing effect.
Below steps describes the issue:
1)Initially assume both buffers FB0 and FB1 are programmed for buffer-0.
2)On EOF0: Program FB0 for buffer-1, indicate(wake up) application
to fill up buffer-0. As FB1 is active and continues to DMA buffer-0
(which is being filled), leading to tearing/flickering issue.
3)On EOF1: Program FB1 for buffer-0, indicate(wake up) application to
fill up buffer-1. As FB0 is active and continues to DMA buffer-1(which
is being filled), leading to tearing/flickering issue.
4)On EOF0: Program FB0 for buffer-1, indicate(wake up) application to
fill up buffer-0. As FB1 is active and continues to DMA buffer-0(which is
being filled), leading to tearing/flickering issue.
...
Above steps depict that issue is because of 1 frame delay in frame
panned by application.
Patch fixes the issue by keeping track free DMA channel and configures
it in drivers PAN callback so that panned frame from application gets
displayed in next frame period.
Wiki below describes the issue in detail and it also has link to
application with which issue can be reproduced.
http://processors.wiki.ti.com/index.php/DA8xx_LCDC_Linux_FB_FAQs
Signed-off-by: Nellutla, Aditya <aditya.n@ti.com>
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Writing '1' to particular bit of IRQENABLE_CLEAR register disables the
corresponding interrupt on revision 2 LCDC. This register was wrongly
configured to disable all previous enabled interrupts instead of
disabling only palette completion interrupt. Patch fixes it by clearing
only palette completion interrupt bit.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
In the real time use-case when SGX is used for rendering to FB buffers it has been
observed that, the available memory from framebuffer driver is not sufficient for
SGX under certain cases (like 16-bit WVGA resolution). SGX requires 2 swap buffers
with each of the buffers aligned to lcm(line_length, PAGE_SIZE).
Inorder to satisfy this requirement, we have two options,
- Increase number of FB buffers (LCD_NUM_BUFFERS) to 3. This is not
recommended as we end up wasting huge memory in most of the cases.
- Align FB buffers to lcm(line_length, PAGE_SIZE).This ensures framebuffer
size is increased to satisfy SGX requirements keeping alignment intact.
This patch makes sure that FB allocates buffers aligned to above formula.
Signed-off-by: Aditya Nellutla <aditya.n@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Add timing data for Hitachi SP10Q010 display and allow configuration
of the 4bpp palette. For 4bpp framebuffer enable reversed order of
pixels in a byte. This requires defining FB_CFB_REV_PIXELS_IN_BYTE
and additionally setting var.nonstd to the value FB_NONSTD_REV_PIX_IN_B.
Note that it is not enough to set da8xx_fb_var.nonstd to this value
statically, since FBIOPUT_VSCREENINFO ioctl might pass var struct with
.nonstd field set to zero or another value. Therefore this setting must
be adjusted in fb_check_var() according to the requested bpp value.
Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Patch calculates pixel clock period in pico seconds and updates
the same in variable screen information structure. fbset utility
uses this information.
Signed-off-by: Manjunathappa, Prakash <prakash.pm@ti.com>
Signed-off-by: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Manish Badarkhe