There is a difference in the bit position of the normal interrupt summary
enable (NIE) and abnormal interrupt summary enable (AIE) between revisions
of the hardware. For older revisions the NIE and AIE bits are positions
16 and 15 respectively. For newer revisions the NIE and AIE bits are
positions 15 and 14. The effect in changing the bit position is that
newer hardware won't receive AIE interrupts in the current version of the
driver. Specifically, the driver uses this interrupt to collect
statistics on when a receive buffer unavailable event occurs and to
restart the driver/device when a fatal bus error occurs.
Update the driver to set the interrupt enable bit based on the reported
version of the hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc says:
====================
nsh: headers, GSO
This adds header structs and helpers for NSH together with GSO support.
Note there is no code in this patchset that actually manipulates the NSH
headers. That was sent to netdev by Yi Yang ("[PATCH net-next v6 0/3]
openvswitch: add NSH support"). The aim of this series is to lay the
groundwork and ease the implementation for him.
In addition to openvswitch, the NSH support should be added to tc (flower to
match, act_nsh to push/pop NSH headers). That will come later. There's
currently no plan to support NSH by other means than those two.
The patch 3 in this patchset was written by Yi Yang, I took it from the
aforementioned series and slightly modified it - see the note in the patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new nsh/ directory. It currently holds only GSO functions but more
will come: in particular, code shared by openvswitch and tc to manipulate
NSH headers.
For now, assume there's no hardware support for NSH segmentation. We can
always introduce netdev->nsh_features later.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NSH (Network Service Header)[1] is a new protocol for service
function chaining, it can be handled as a L3 protocol like
IPv4 and IPv6, Eth + NSH + Inner packet or VxLAN-gpe + NSH +
Inner packet are two typical use cases.
This patch adds NSH header structures and helpers for NSH GSO
support and Open vSwitch NSH support.
[1] https://datatracker.ietf.org/doc/draft-ietf-sfc-nsh/
[Jiri: added nsh_hdr() helper and renamed the header struct to "struct
nshhdr" to match the usual pattern. Removed packet type defines, these are
now shared with VXLAN-GPE.]
Signed-off-by: Yi Yang <yi.y.yang@intel.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The values are shared between VXLAN-GPE and NSH. Originally probably by
coincidence but I notified both working groups about this last year and they
seem to keep the values in sync since then.
Hopefully they'll get a single IANA registry for the values, too. (I asked
them for that.)
Factor out the code to be shared by the NSH implementation.
NSH and MPLS values are added in this patch, too. For MPLS, the drafts
incorrectly assign only a single value, while we have two MPLS ethertypes.
I raised the problem with both groups. For now, I assume the value is for
unicast.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NSH draft says:
An IEEE EtherType, 0x894F, has been allocated for NSH.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring says:
====================
tc: act_ife: handle IEEE IFE ethertype as default
this patch series will introduce the IFE ethertype which is registered by
IEEE. If the netlink act_ife type netlink attribute is not given it will
use this value by default now.
At least it will introduce some UAPI testcases to check if the default type
is used if not specified and vice versa.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new testcase for the IFE type setting in tc. In case
of user specified the type it will check if the ife is correctly
configured to react on it. If it's not specified the default IFE type
should be used.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch handles a default IFE type if it's not given by user space
netlink api. The default IFE type will be the registered ethertype by
IEEE for IFE ForCES.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the forces IFE lfb type according to IEEE registered
ethertypes. See http://standards-oui.ieee.org/ethertype/eth.txt for more
information. Since there exists the IFE subsystem it can be used there.
This patch also use the correct word "ForCES" instead of "FoRCES" which
is a spelling error inside the IEEE ethertype specification.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Explain that the patch queue in patchwork should not be touched by patch
submitters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pavel Belous says:
====================
net:ethernet:aquantia: Atlantic driver Update 2017-08-23
This series contains updates for aQuantia Atlantic driver.
It has bugfixes and some improvements.
Changes in v2:
- "MCP state change" fix removed (will be sent as
a separate fix after further investigation.)
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
We should inform user about wrong firmware version
by printing message in dmesg.
Fixes: 3d2ff7eebe26 ("net: ethernet: aquantia: Atlantic hardware abstraction layer")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the HW supports up to 32 multicast filters we should
track count of multicast filters to avoid overflow.
If we attempt to add >32 multicast filter - just set NETIF_ALLMULTI flag
instead.
Fixes: 94f6c9e4cdf6 ("net: ethernet: aquantia: Support for NIC-specific code")
Signed-off-by: Igor Russkikh <Igor.Russkikh@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver choose the optimal interrupt throttling settings depends
of current link speed.
Due this bug link_status field from aq_hw is never updated and as result
always used same interrupt throttling values.
Fixes: 3d2ff7eebe26 ("net: ethernet: aquantia: Atlantic hardware abstraction layer")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The hardware has the HW Checksum Offload bug when small
TCP patckets (with length <= 60 bytes) has wrong "checksum valid" bit.
The solution is - ignore checksum valid bit for small packets
(with length <= 60 bytes) and mark this as CHECKSUM_NONE to allow
network stack recalculate checksum itself.
Fixes: ccf9a5ed14be ("net: ethernet: aquantia: Atlantic A0 and B0 specific functions.")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of RSS queues should be not more than numbers of CPU.
Its does not make sense to increase perfomance, and also cause problems on
some motherboards.
Fixes: 94f6c9e4cdf6 ("net: ethernet: aquantia: Support for NIC-specific code")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes datapath spinlocks which does not perform any
useful work.
Fixes: 6e70637f9f1e ("net: ethernet: aquantia: Add ring support code")
Signed-off-by: Pavel Belous <Pavel.Belous@aquantia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
... which may happen with certain values of tp_reserve and maclen.
Fixes: 58d19b19cd ("packet: vnet_hdr support for tpacket_rcv")
Signed-off-by: Benjamin Poirier <bpoirier@suse.com>
Cc: Willem de Bruijn <willemb@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
For a bond slave device as a tipc bearer, the dev represents the bond
interface and orig_dev represents the slave in tipc_l2_rcv_msg().
Since we decode the tipc_ptr from bonding device (dev), we fail to
find the bearer and thus tipc links are not established.
In this commit, we register the tipc protocol callback per device and
look for tipc bearer from both the devices.
Signed-off-by: Parthasarathy Bhuvaragan <parthasarathy.bhuvaragan@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tariq Toukan says:
====================
mlx4 misc patches
This patchset contains misc patches from the team
to the mlx4 Core and Eth drivers.
Patch 1 by Eran replaces large static allocations by dynamic ones.
Patch 2 by Leon makes an explicit conversion and solves a smatch warning.
In patch 3 I fix a misplaced brackets of the sizeof operation.
Patch 4 by Moshe adds the ability to inform the FW regarding user mac updates.
Series generated against net-next commit:
901c5d2fbf ARM: dts: rk3228-evb: Fix the compiling error
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding support for updating the FW on new port mac, when port mac change
is requested by the user. This info is required by the FW as OEM
management tools require this info directly from the NIC FW.
Check device capability bit to verify the FW supports user mac.
If the FW does support it, use set_port command to notify the FW on the
new mac.
The feature is relevant only to PF port mac.
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When changing the sizeof style usage in the patch cited below,
one brackets misplacement was introduced. Here we fix it.
Fixes: 31975e27a4 ("mlx4: sizeof style usage")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The "lg" variable is declared as int so in all places where this variable
is used as a shift operand, the output will be int too.
This produces the following smatch warning:
drivers/net/ethernet/mellanox/mlx4/fw.c:1532 mlx4_map_cmd() warn:
should '1 << lg' be a 64 bit type?
Simple declaration of "1" to be "1ULL" will fix the issue.
Fixes: 225c7b1fee ("IB/mlx4: Add a driver Mellanox ConnectX InfiniBand adapters")
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In order to avoid temporary large structs on the stack,
allocate them dynamically.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Tal Alon <talal@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A few useful tracepoints to trace bridge forwarding
database updates.
Signed-off-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
Endian fixes for SYSTEMPORT/SF2/MDIO
While trying an ARM BE kernel for kinks, the 3 drivers below started not
working and the reasons why became pretty obvious because the register space
remains LE (hardwired), except for Broadcom MIPS where it follows the CPU's
native endian (let's call that a feature).
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver currently uses __raw_{read,write}l which works for all
platforms supported: Broadcom MIPS LE/BE (native endian), ARM LE (native
endian) but not ARM BE (registers are still LE). Switch to using the
proper accessors for all platforms and explain why Broadcom MIPS BE is
special here, in doing so, we introduce a couple of helper functions to
abstract these differences.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RSB_SWAP0 needs to match the host CPU endian, and it needs to be set
for LE and clear for BE. RSB_SWAP1 must always be cleared for SYSTEMPORT
Lite.
With these settings, we have the Receive Status Block always match the
host endian and we do not need to perform any conversion. Since there is
not necessarily a CONFIG_CPU_LITTLE_ENDIAN option defined, we test for
!CONFIG_CPU_BIG_ENDIAN which is guaranteed to be set.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The Starfigther 2 driver currently uses __raw_{read,write}l which means
native I/O endian. This works correctly for an ARM LE kernel (default)
but fails miserably on an ARM BE (BE8) kernel where registers are kept
little endian, so replace uses with {read,write}l_relaxed here which is
what we want because this is all performance sensitive code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SYSTEMPORT driver currently uses __raw_{read,write}l which means
native I/O endian. This works correctly for an ARM LE kernel (default)
but fails miserably on an ARM BE (BE8) kernel where registers are kept
little endian, so replace uses with {read,write}l_relaxed here which is
what we want because this is all performance sensitive code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
vmwgfx currently cannot support non-blocking commit because when
vmw_*_crtc_page_flip is called, drm_atomic_nonblocking_commit()
schedules the update on a thread. This means vmw_*_crtc_page_flip
cannot rely on the new surface being bound before the subsequent
dirty and flush operations happen.
Cc: <stable@vger.kernel.org> # 4.12.x
Signed-off-by: Sinclair Yeh <syeh@vmware.com>
Reviewed-by: Thomas Hellstrom <thellstrom@vmware.com>
Reviewed-by: Charmaine Lee <charmainel@vmware.com>
This fixes compiler errors in perf such as:
tests/attr.c: In function 'store_event':
tests/attr.c:66:27: error: format '%llu' expects argument of type 'long long unsigned int', but argument 6 has type '__u64 {aka long unsigned int}' [-Werror=format=]
snprintf(path, PATH_MAX, "%s/event-%d-%llu-%d", dir,
^
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Tested-by: Michael Cree <mcree@orcon.net.nz>
Cc: stable@vger.kernel.org
Signed-off-by: Matt Turner <mattst88@gmail.com>
Commit 3cc2dac5be ("drivers/video/fbdev/atyfb: Replace MTRR UC hole
with strong UC") introduces calls to ioremap_wc and ioremap_uc. This
causes build failures with alpha:allmodconfig. Map the missing functions
to ioremap_nocache.
Fixes: 3cc2dac5be ("drivers/video/fbdev/atyfb:
Replace MTRR UC hole with strong UC")
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Luis R. Rodriguez <mcgrof@suse.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Since commit 71810db27c (modversions: treat symbol CRCs
as 32 bit quantities) R_ALPHA_REFLONG relocations can be required
to load modules. This implements it.
Tested-by: Bob Tracy <rct@gherkin.frus.com>
Reviewed-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Michael Cree <mcree@orcon.net.nz>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Patch 8525023121 introduced a typo.
That said, the identity AND insns added by that patch are more
clearly written as MOV. At the same time, re-schedule the ev6
version so that the first dispatch can execute in parallel.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Matt Turner <mattst88@gmail.com>
There are direct branches between {str*cpy,str*cat} and stx*cpy.
Ensure the branches are within range by merging these objects.
Signed-off-by: Richard Henderson <rth@twiddle.net>
Signed-off-by: Matt Turner <mattst88@gmail.com>
Pull cgroup fix from Tejun Heo:
"A late but obvious fix for cgroup.
I broke the 'cpuset.memory_pressure' file a long time ago (v4.4) by
accidentally deleting its file index, which made it a duplicate of the
'cpuset.memory_migrate' file. Spotted and fixed by Waiman"
* 'for-4.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
cpuset: Fix incorrect memory_pressure control file mapping
Pull libata fixes from Tejun Heo:
"Late fixes for libata. There's a minor platform driver fix but the
important one is READ LOG PAGE.
This is a new ATA command which is used to test some optional features
but it broke probing of some devices - they locked up instead of
failing the unknown command.
Christoph tried blacklisting, but, after finding out there are
multiple devices which fail this way, backed off to testing feature
bit in IDENTIFY data first, which is a bit lossy (we can miss features
on some devices) but should be a lot safer"
* 'for-4.13-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
Revert "libata: quirk read log on no-name M.2 SSD"
libata: check for trusted computing in IDENTIFY DEVICE data
libata: quirk read log on no-name M.2 SSD
sata: ahci-da850: Fix some error handling paths in 'ahci_da850_probe()'
rsi driver is getting a lot of new features lately, but as usual
active development happening on iwlwifi as well as other drivers.
I pulled wireless-drivers to fix multiple conflicts in iwlwifi and to
make it easier further development.
Major changes:
ath10k
* initial UBS bus support (no full support yet)
* add tdls support for 10.4 firmware
ath9k
* add Dell Wireless 1802
wil6210
* support FW RSSI reporting
rsi
* support legacy power save, U-APSD, rf-kill and AP mode
* RTS threshold configuration
brcmfmac
* support CYW4373 SDIO/USB chipset
iwlwifi
* some more code moved to a new directory
* add new PCI ID for 7265D
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJZo9ubAAoJEG4XJFUm622bgTMIAIoYA4hNR17lkrsfuHztwo/p
LM1biXej9dbRT5VNEVP4mlUVrKKakRt46YpW+UMdAI3KSNhqiNTM418126LUPpqn
FIa5SKwoAB1S8g9dIBEpyfZVU9EnuyQ2XoW9ochBikrtQN71fW17G3EqRthiTbqH
pWBA8RgKpLyjFs2Iupz8IJ8J5jK7qnIBo+wD5Px31U2rEiaE2/kCQPcVoM9aaNgD
zJHFyVQgT2X76mD14B1R0tPyjEWDEmaWLW92jII+6Oxr6vnBguuyY1MKB1aejjmy
UiKqf/znKrCYS8JepV+ayRqRThFYnNbO5UOCDnuQqCLkxcUAjvCkovamG+x9QBE=
=IR0O
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2017-08-28' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 4.14
rsi driver is getting a lot of new features lately, but as usual
active development happening on iwlwifi as well as other drivers.
I pulled wireless-drivers to fix multiple conflicts in iwlwifi and to
make it easier further development.
Major changes:
ath10k
* initial UBS bus support (no full support yet)
* add tdls support for 10.4 firmware
ath9k
* add Dell Wireless 1802
wil6210
* support FW RSSI reporting
rsi
* support legacy power save, U-APSD, rf-kill and AP mode
* RTS threshold configuration
brcmfmac
* support CYW4373 SDIO/USB chipset
iwlwifi
* some more code moved to a new directory
* add new PCI ID for 7265D
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
clk_div_table are not supposed to change at runtime.
meson8b_dwmac structure is working with const clk_div_table.
So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ChunYu found a kernel warn_on during syzkaller fuzzing:
[40226.038539] WARNING: CPU: 5 PID: 23720 at net/ipv4/af_inet.c:152 inet_sock_destruct+0x78d/0x9a0
[40226.144849] Call Trace:
[40226.147590] <IRQ>
[40226.149859] dump_stack+0xe2/0x186
[40226.176546] __warn+0x1a4/0x1e0
[40226.180066] warn_slowpath_null+0x31/0x40
[40226.184555] inet_sock_destruct+0x78d/0x9a0
[40226.246355] __sk_destruct+0xfa/0x8c0
[40226.290612] rcu_process_callbacks+0xaa0/0x18a0
[40226.336816] __do_softirq+0x241/0x75e
[40226.367758] irq_exit+0x1f6/0x220
[40226.371458] smp_apic_timer_interrupt+0x7b/0xa0
[40226.376507] apic_timer_interrupt+0x93/0xa0
The warn_on happned when sk->sk_rmem_alloc wasn't 0 in inet_sock_destruct.
As after commit f970bd9e3a ("udp: implement memory accounting helpers"),
udp has changed to use udp_destruct_sock as sk_destruct where it would
udp_rmem_release all rmem.
But IPV6_ADDRFORM sockopt sets sk_destruct with inet_sock_destruct after
changing family to PF_INET. If rmem is not 0 at that time, and there is
no place to release rmem before calling inet_sock_destruct, the warn_on
will be triggered.
This patch is to fix it by not setting sk_destruct in IPV6_ADDRFORM sockopt
any more. As IPV6_ADDRFORM sockopt only works for tcp and udp. TCP sock has
already set it's sk_destruct with inet_sock_destruct and UDP has set with
udp_destruct_sock since they're created.
Fixes: f970bd9e3a ("udp: implement memory accounting helpers")
Reported-by: ChunYu Wang <chunwang@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jesper Dangaard Brouer says:
====================
XDP redirect tracepoints
I feel this is as far as I can take the tracepoint infrastructure to
assist XDP monitoring.
Tracepoints comes with a base overhead of 25 nanosec for an attached
bpf_prog, and 48 nanosec for using a full perf record. This is
problematic for the XDP use-case, but it is very convenient to use the
existing perf infrastructure.
From a performance perspective, the real solution would be to attach
another bpf_prog (that understand xdp_buff), but I'm not sure we want
to introduce yet another bpf attach API for this.
One thing left is to standardize the possible err return codes, to a
limited set, to allow easier (and faster) mapping into a bpf map.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This tool xdp_monitor demonstrate how to use the different xdp_redirect
tracepoints xdp_redirect{,_map}{,_err} from a BPF program.
The default mode is to only monitor the error counters, to avoid
affecting the per packet performance. Tracepoints comes with a base
overhead of 25 nanosec for an attached bpf_prog, and 48 nanosec for
using a full perf record (with non-matching filter). Thus, default
loading the --stats mode could affect the maximum performance.
This version of the tool is very simple and count all types of errors
as one. It will be natural to extend this later with the different
types of errors that can occur, which should help users quickly
identify common mistakes.
Because the TP_STRUCT was kept in sync all the tracepoints loads the
same BPF code. It would also be natural to extend the map version to
demonstrate how the map information could be used.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Acked-by: Alexei Starovoitov <ast@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
For supporting XDP_REDIRECT, a device driver must (obviously)
implement the "TX" function ndo_xdp_xmit(). An additional requirement
is you cannot TX out a device, unless it also have a xdp bpf program
attached. This dependency is caused by the driver code need to setup
XDP resources before it can ndo_xdp_xmit.
Update bpf samples xdp_redirect and xdp_redirect_map to automatically
attach a dummy XDP program to the configured ifindex_out device. Use
the XDP flag XDP_FLAGS_UPDATE_IF_NOEXIST on the dummy load, to avoid
overriding an existing XDP prog on the device.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Creating as specific xdp_redirect_map variant of the xdp tracepoints
allow users to write simpler/faster BPF progs that get attached to
these tracepoints.
Goal is to still keep the tracepoints in xdp_redirect and xdp_redirect_map
similar enough, that a tool can read the top part of the TP_STRUCT and
produce similar monitor statistics.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Lendacky