Jeff Kirsher says:
====================
Intel Wired LAN Driver Updates 2017-09-05
This series contains fixes for i40e only.
These two patches fix an issue where our nvmupdate tool does not work on RHEL 7.4
and newer kernels, in fact, the use of the nvmupdate tool on newer kernels can
cause the cards to be non-functional unless these patches are applied.
Anjali reworks the locking around accessing the NVM so that NVM acquire timeouts
do not occur which was causing the failed firmware updates.
Jake correctly updates the wb_desc when reading the NVM through the AdminQ.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
When introducing the functions to read the NVM through the AdminQ, we
did not correctly mark the wb_desc.
Fixes: 7073f46e44 ("i40e: Add AQ commands for NVM Update for X722", 2015-06-05)
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
X722 devices use the AdminQ to access the NVM, and this requires taking
the AdminQ lock. Because of this, we lock the AdminQ during
i40e_read_nvm(), which is also called in places where the lock is
already held, such as the firmware update path which wants to lock once
and then unlock when finished after performing several tasks.
Although this should have only affected X722 devices, commit
96a39aed25 ("i40e: Acquire NVM lock before reads on all devices",
2016-12-02) added locking for all NVM reads, regardless of device
family.
This resulted in us accidentally causing NVM acquire timeouts on all
devices, causing failed firmware updates which left the eeprom in
a corrupt state.
Create unsafe non-locked variants of i40e_read_nvm_word and
i40e_read_nvm_buffer, __i40e_read_nvm_word and __i40e_read_nvm_buffer
respectively. These variants will not take the NVM lock and are expected
to only be called in places where the NVM lock is already held if
needed.
Since the only caller of i40e_read_nvm_buffer() was in such a path,
remove it entirely in favor of the unsafe version. If necessary we can
always add it back in the future.
Additionally, we now need to hold the NVM lock in i40e_validate_checksum
because the call to i40e_calc_nvm_checksum now assumes that the NVM lock
is held. We can further move the call to read I40E_SR_SW_CHECKSUM_WORD
up a bit so that we do not need to acquire the NVM lock twice.
This should resolve firmware updates and also fix potential raise that
could have caused the driver to report an invalid NVM checksum upon
driver load.
Reported-by: Stefan Assmann <sassmann@kpanic.de>
Fixes: 96a39aed25 ("i40e: Acquire NVM lock before reads on all devices", 2016-12-02)
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Iyappan Subramanian says:
====================
drivers: net: xgene: Misc bug fixes
This patch set fixes bugs related to handling the case for ACPI for,
reading and programming tx/rx delay values.
====================
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
commit 183db4 ("drivers: net: xgene: Correct probe sequence handling")
changed the return type of xgene_enet_check_phy_handle() to void.
This patch, removes the return statement from the last line.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes configuring tx/rx delay values for ACPI.
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes reading tx/rx delay values for ACPI.
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The function calls to kcalloc use wrong parameter order and incorrect flags
values. GFP_KERNEL is used instead of flags now and the order is corrected.
The change was done using the following coccinelle script:
@@
expression E1,E2;
type T;
@@
-kcalloc(E1, E2, sizeof(T))
+kcalloc(E2, sizeof(T), GFP_KERNEL)
Signed-off-by: Zahari Doychev <zahari.doychev@linux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bits in m_flags in struct rds_message are used for a plurality of
reasons, and from different contexts. To avoid any missing updates to
m_flags, use the atomic set_bit() instead of the non-atomic equivalent.
Signed-off-by: Håkon Bugge <haakon.bugge@oracle.com>
Reviewed-by: Knut Omang <knut.omang@oracle.com>
Reviewed-by: Wei Lin Guay <wei.lin.guay@oracle.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We check tx avail through vhost_enable_notify() in the past which is
wrong since it only checks whether or not guest has filled more
available buffer since last avail idx synchronization which was just
done by vhost_vq_avail_empty() before. What we really want is checking
pending buffers in the avail ring. Fix this by calling
vhost_vq_avail_empty() instead.
This issue could be noticed by doing netperf TCP_RR benchmark as
client from guest (but not host). With this fix, TCP_RR from guest to
localhost restores from 1375.91 trans per sec to 55235.28 trans per
sec on my laptop (Intel(R) Core(TM) i7-5600U CPU @ 2.60GHz).
Fixes: 0308813724 ("vhost_net: basic polling support")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mdio_mux_init() use the parameter dev for two distinct thing:
1) Have a device for all devm_ functions
2) Get device_node from it
Since it is two distinct purpose, this patch add a parameter mdio_mux
that is linked to task 2.
This will also permit to register an of_node mdio-mux that lacks a direct
owning device.
For example a mdio-mux which is a subnode of a real device.
Signed-off-by: Corentin Labbe <clabbe.montjoie@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an RxRPC service packet comes in, the target connection is looked up
by an rb-tree search under RCU and a read-locked seqlock; the seqlock retry
check is, however, currently skipped if we got a match, but probably
shouldn't be in case the connection we found gets replaced whilst we're
doing a search.
Make the lookup procedure always go through need_seqretry(), even if the
lookup was successful. This makes sure we always pick up on a write-lock
event.
On the other hand, since we don't take a ref on the object, but rely on RCU
to prevent its destruction after dropping the seqlock, I'm not sure this is
necessary.
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This code is no longer used, the logging function was changed by commit
fbca164776 ("net: stmmac: Use the right logging function in stmmac_mdio_register").
It was previously showing information about the type of the IRQ, if it's
polled, ignored or a normal interrupt. As we don't want information loss,
I have moved this code to phy_attached_print().
Fixes: fbca164776 ("net: stmmac: Use the right logging function in stmmac_mdio_register")
Signed-off-by: Romain Perier <romain.perier@collabora.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The wrong register is checked for the Tx flow control bit,
it should have been maccfg1 not maccfg2.
This went unnoticed for so long probably because the impact is
hardly visible, not to mention the tangled code from adjust_link().
First, link flow control (i.e. handling of Rx/Tx link level pause frames)
is disabled by default (needs to be enabled via 'ethtool -A').
Secondly, maccfg2 always returns 0 for tx_flow_oldval (except for a few
old boards), which results in Tx flow control remaining always on
once activated.
Fixes: 45b679c9a3 ("gianfar: Implement PAUSE frame generation support")
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPS_TX_INT_CAUSE[Bubble] is a normal condition for T6, hence
ignore this interrupt for T6.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MPS_STAT_CTL[CountPauseStatTx] and MPS_STAT_CTL[CountPauseStatRx]
only control whether or not Pause Frames will be counted as part
of the 64-Byte Tx/Rx Frame counters. These bits do not control
whether Pause Frames are counted in the Total Tx/Rx Frames/Bytes
counters.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
do not reuse the loop counter which is used iterate over
the ports, so that sched_tbl will be freed for all the ports.
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename "generic_xdp" to "skb_xdp" to avoid confusing it with the
generic XDP which will be done at netif_receive_skb().
Cc: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We reserve headroom unconditionally which could cause unnecessary
stress on socket memory accounting because of increased trusesize. Fix
this by only reserve extra headroom when XDP is set.
Cc: Jakub Kicinski <kubakici@wp.pl>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian Fainelli says:
====================
net: dsa: Allow switch drivers to indicate number of TX queues
This patch series extracts the parts of the patch set that are likely not to be
controversial and actually bringing multi-queue support to DSA-created network
devices.
With these patches, we can now use sch_multiq as documented under
Documentation/networking/multique.txt and let applications dedice the switch
port output queue they want to use. Currently only Broadcom tags utilize that
information.
Resending based on David's feedback regarding the patches not in patchwork.
Changes in v2:
- use a proper define for the number of TX queues in bcm_sf2.c (Andrew)
Changes from RFC:
- dropped the ability to configure RX queues since we don't do anything with
those just yet
- dropped the patches that dealt with binding the DSA slave network devices
queues with their master network devices queues this will be worked on
separately.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Even though TC2QOS mapping is for switch egress queues, we need to
configure it correclty in order for the Broadcom tag ingress (CPU ->
switch) queue selection to work correctly since there is a 1:1 mapping
between switch egress queues and ingress queues.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The switch supports 8 egress queues per port, so indicate that such that
net/dsa/slave.c::dsa_slave_create can allocate the right number of TX queues.
While at it use SF2_NUM_EGRESS_QUEUE as a define for the number of queues we
support.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We originally used skb->priority but that was not quite correct as this
bitfield needs to contain the egress switch queue we intend to send this
SKB to.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Let switch drivers indicate how many TX queues they support. Some
switches, such as Broadcom Starfighter 2 are designed with 8 egress
queues. Future changes will allow us to leverage the queue mapping and
direct the transmission towards a particular queue.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Instead of using ifdef in the C file.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Suggested-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Tested-by: Yotam Gigi <yotamg@mellanox.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use ARRAY_SIZE macro, rather than explicitly coding some variant of it
yourself.
Found with: find -type f -name "*.c" -o -name "*.h" | xargs perl -p -i -e
's/\bsizeof\s*\(\s*(\w+)\s*\)\s*\ /\s*sizeof\s*\(\s*\1\s*\[\s*0\s*\]\s*\)
/ARRAY_SIZE(\1)/g' and manual check/verification.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Tom Herbert says:
====================
flow_dissector: Flow dissector fixes
This patch set fixes some basic issues with __skb_flow_dissect function.
Items addressed:
- Cleanup control flow in the function; in particular eliminate a
bunch of goto's and implement a simplified control flow model
- Add limits for number of encapsulations and headers that can be
dissected
v2:
- Simplify the logic for limits on flow dissection. Just set the
limit based on the number of headers the flow dissector can
processes. The accounted headers includes encapsulation headers,
extension headers, or other shim headers.
Tested:
Ran normal traffic, GUE, and VXLAN traffic.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
In flow dissector there are no limits to the number of nested
encapsulations or headers that might be dissected which makes for a
nice DOS attack. This patch sets a limit of the number of headers
that flow dissector will parse.
Headers includes network layer headers, transport layer headers, shim
headers for encapsulation, IPv6 extension headers, etc. The limit for
maximum number of headers to parse has be set to fifteen to account for
a reasonable number of encapsulations, extension headers, VLAN,
in a packet. Note that this limit does not supercede the STOP_AT_*
flags which may stop processing before the headers limit is reached.
Reported-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
__skb_flow_dissect is riddled with gotos that make discerning the flow,
debugging, and extending the capability difficult. This patch
reorganizes things so that we only perform goto's after the two main
switch statements (no gotos within the cases now). It also eliminates
several goto labels so that there are only two labels that can be target
for goto.
Reported-by: Alexander Popov <alex.popov@linux.com>
Signed-off-by: Tom Herbert <tom@quantonium.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
A header file cleanup apparently caused a build regression
with one driver using the knav infrastructure:
In file included from drivers/net/ethernet/ti/netcp_core.c:30:0:
include/linux/soc/ti/knav_dma.h:129:30: error: field 'direction' has incomplete type
enum dma_transfer_direction direction;
^~~~~~~~~
drivers/net/ethernet/ti/netcp_core.c: In function 'netcp_txpipe_open':
drivers/net/ethernet/ti/netcp_core.c:1349:21: error: 'DMA_MEM_TO_DEV' undeclared (first use in this function); did you mean 'DMA_MEMORY_MAP'?
config.direction = DMA_MEM_TO_DEV;
^~~~~~~~~~~~~~
DMA_MEMORY_MAP
drivers/net/ethernet/ti/netcp_core.c:1349:21: note: each undeclared identifier is reported only once for each function it appears in
drivers/net/ethernet/ti/netcp_core.c: In function 'netcp_setup_navigator_resources':
drivers/net/ethernet/ti/netcp_core.c:1659:22: error: 'DMA_DEV_TO_MEM' undeclared (first use in this function); did you mean 'DMA_DESC_HOST'?
config.direction = DMA_DEV_TO_MEM;
As the header is no longer included implicitly through netdevice.h,
we should include it in the header that references the enum.
Fixes: 0dd5759dbb ("net: remove dmaengine.h inclusion from netdevice.h")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
We get a new link error in allmodconfig kernels after ftgmac100
started using the ncsi helpers:
ERROR: "ncsi_vlan_rx_kill_vid" [drivers/net/ethernet/faraday/ftgmac100.ko] undefined!
ERROR: "ncsi_vlan_rx_add_vid" [drivers/net/ethernet/faraday/ftgmac100.ko] undefined!
Related to that, we get another error when CONFIG_NET_NCSI is disabled:
drivers/net/ethernet/faraday/ftgmac100.c:1626:25: error: 'ncsi_vlan_rx_add_vid' undeclared here (not in a function); did you mean 'ncsi_start_dev'?
drivers/net/ethernet/faraday/ftgmac100.c:1627:26: error: 'ncsi_vlan_rx_kill_vid' undeclared here (not in a function); did you mean 'ncsi_vlan_rx_add_vid'?
This fixes both problems at once, using a 'static inline' stub helper
for the disabled case, and exporting the functions when they are present.
Fixes: 51564585d8 ("ftgmac100: Support NCSI VLAN filtering when available")
Fixes: 21acf63013 ("net/ncsi: Configure VLAN tag filter")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo Neira Ayuso says:
====================
Netfilter updates for next-net (part 2)
The following patchset contains Netfilter updates for net-next. This
patchset includes updates for nf_tables, removal of
CONFIG_NETFILTER_DEBUG and a new mode for xt_hashlimit. More
specifically, they:
1) Add new rate match mode for hashlimit, this introduces a new revision
for this match. The idea is to stop matching packets until ratelimit
criteria stands true. Patch from Vishwanath Pai.
2) Add ->select_ops indirection to nf_tables named objects, so we can
choose between different flavours of the same object type, patch from
Pablo M. Bermudo.
3) Shorter function names in nft_limit, basically:
s/nft_limit_pkt_bytes/nft_limit_bytes, also from Pablo M. Bermudo.
4) Add new stateful limit named object type, this allows us to create
limit policies that you can identify via name, also from Pablo.
5) Remove unused hooknum parameter in conntrack ->packet indirection.
From Florian Westphal.
6) Patches to remove CONFIG_NETFILTER_DEBUG and macros such as
IP_NF_ASSERT and IP_NF_ASSERT. From Varsha Rao.
7) Add nf_tables_updchain() helper function and use it from
nf_tables_newchain() to make it more maintainable. Similarly,
add nf_tables_addchain() and use it too.
8) Add new netlink NLM_F_NONREC flag, this flag should only be used for
deletion requests, specifically, to support non-recursive deletion.
Based on what we discussed during NFWS'17 in Faro.
9) Use NLM_F_NONREC from table and sets in nf_tables.
10) Support for recursive chain deletion. Table and set deletion
commands come with an implicit content flush on deletion, while
chains do not. This patch addresses this inconsistency by adding
the code to perform recursive chain deletions. This also comes with
the bits to deal with the new NLM_F_NONREC netlink flag.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch sorts out an asymmetry in deletions. Currently, table and set
deletion commands come with an implicit content flush on deletion.
However, chain deletion results in -EBUSY if there is content in this
chain, so no implicit flush happens. So you have to send a flush command
in first place to delete chains, this is inconsistent and it can be
annoying in terms of user experience.
This patch uses the new NLM_F_NONREC flag to request non-recursive chain
deletion, ie. if the chain to be removed contains rules, then this
returns EBUSY. This problem was discussed during the NFWS'17 in Faro,
Portugal. In iptables, you hit -EBUSY if you try to delete a chain that
contains rules, so you have to flush first before you can remove
anything. Since iptables-compat uses the nf_tables netlink interface, it
has to use the NLM_F_NONREC flag from userspace to retain the original
iptables semantics, ie. bail out on removing chains that contain rules.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Bail out if user requests non-recursive deletion for tables and sets.
This new flags tells nf_tables netlink interface to reject deletions if
tables and sets have content.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
In the last NFWS in Faro, Portugal, we discussed that netlink is lacking
the semantics to request non recursive deletions, ie. do not delete an
object iff it has child objects that hang from this parent object that
the user requests to be deleted.
We need this new flag to solve a problem for the iptables-compat
backward compatibility utility, that runs iptables commands using the
existing nf_tables netlink interface. Specifically, custom chains in
iptables cannot be deleted if there are rules in it, however, nf_tables
allows to remove any chain that is populated with content. To sort out
this asymmetry, iptables-compat userspace sets this new NLM_F_NONREC
flag to obtain the same semantics that iptables provides.
This new flag should only be used for deletion requests. Note this new
flag value overlaps with the existing:
* NLM_F_ROOT for get requests.
* NLM_F_REPLACE for new requests.
However, those flags should not ever be used in deletion requests.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
nf_tables_newchain() is too large, wrap the chain update path in a
function to make it more maintainable.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch removes CONFIG_NETFILTER_DEBUG and _ASSERT() macros as they
are no longer required. Replace _ASSERT() macros with WARN_ON().
Signed-off-by: Varsha Rao <rvarsha016@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Register a new limit stateful object type into the stateful object
infrastructure.
Signed-off-by: Pablo M. Bermudo Garay <pablombg@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Just a small refactor patch in order to improve the code readability.
Signed-off-by: Pablo M. Bermudo Garay <pablombg@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds support for overloading stateful objects operations
through the select_ops() callback, just as it is implemented for
expressions.
This change is needed for upcoming additions to the stateful objects
infrastructure.
Signed-off-by: Pablo M. Bermudo Garay <pablombg@gmail.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds a new feature to hashlimit that allows matching on the
current packet/byte rate without rate limiting. This can be enabled
with a new flag --hashlimit-rate-match. The match returns true if the
current rate of packets is above/below the user specified value.
The main difference between the existing algorithm and the new one is
that the existing algorithm rate-limits the flow whereas the new
algorithm does not. Instead it *classifies* the flow based on whether
it is above or below a certain rate. I will demonstrate this with an
example below. Let us assume this rule:
iptables -A INPUT -m hashlimit --hashlimit-above 10/s -j new_chain
If the packet rate is 15/s, the existing algorithm would ACCEPT 10
packets every second and send 5 packets to "new_chain".
But with the new algorithm, as long as the rate of 15/s is sustained,
all packets will continue to match and every packet is sent to new_chain.
This new functionality will let us classify different flows based on
their current rate, so that further decisions can be made on them based on
what the current rate is.
This is how the new algorithm works:
We divide time into intervals of 1 (sec/min/hour) as specified by
the user. We keep track of the number of packets/bytes processed in the
current interval. After each interval we reset the counter to 0.
When we receive a packet for match, we look at the packet rate
during the current interval and the previous interval to make a
decision:
if [ prev_rate < user and cur_rate < user ]
return Below
else
return Above
Where cur_rate is the number of packets/bytes seen in the current
interval, prev is the number of packets/bytes seen in the previous
interval and 'user' is the rate specified by the user.
We also provide flexibility to the user for choosing the time
interval using the option --hashilmit-interval. For example the user can
keep a low rate like x/hour but still keep the interval as small as 1
second.
To preserve backwards compatibility we have to add this feature in a new
revision, so I've created revision 3 for hashlimit. The two new options
we add are:
--hashlimit-rate-match
--hashlimit-rate-interval
I have updated the help text to add these new options. Also added a few
tests for the new options.
Suggested-by: Igor Lubashev <ilubashe@akamai.com>
Reviewed-by: Josh Hunt <johunt@akamai.com>
Signed-off-by: Vishwanath Pai <vpai@akamai.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Johan Hedberg says:
====================
pull request: bluetooth-next 2017-09-03
Here's one last bluetooth-next pull request for the 4.14 kernel:
- NULL pointer fix in ca8210 802.15.4 driver
- A few "const" fixes
- New Kconfig option for disabling legacy interfaces
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Subash Abhinov Kasiviswanathan says:
====================
net: qualcomm: rmnet: Fix comments on initial patchset
This series fixes the comments from Dan on the first patch series.
Fixes a memory corruption which could occur if mux_id was higher than 32.
Remove the RMNET_LOCAL_LOGICAL_ENDPOINT which is no longer used.
Make a log message more useful.
Combine __rmnet_set_endpoint_config() with rmnet_set_endpoint_config().
Set the mux_id in rmnet_vnd_newlink().
Set the ingress and egress data format directly in newlink.
Implement ndo_get_iflink to find the real_dev.
Rename the real_dev_info to port to make it similar to other drivers.
The conversion of rmnet_devices to a list and hash lookup will be sent
as part of a seperate patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Make it similar to drivers like ipvlan / macvlan so it is easier to read.
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Cc: Dan Williams <dcbw@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller