SH-3 and SH-4 were trampling the register, and SH-2 wasn't even
setting it in the first place. This ended up with some rather
broken behaviour in the sysrq show_regs().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The code for performing the calculation was only in the SH-4 probe
path, move it out to the common path so the other parts get this
right too.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When a SH7751R system includes a card that has wide range space
like a graphics card, the pci-pci bridge controller can't set the
correct address range.
For example, when *lower_limit is 0xfd000000 and bar_size is
0x4000000, in the following code at arch/sh/drivers/pci/pci-auto.c,
0x0 is set in bar_value.
pciauto_setup_bars()
{
...
bar_value = ((*lower_limit - 1) & ~(bar_size - 1)) + bar_size;
...
*lower_limit = bar_value + bar_size;
}
As a result, 0x4000000 is set in *lower_limit, but this value is wrong.
The following patch avoids this problem by checking the range of the
value and refusing to update the BAR if the calculated value ends up
being bogus.
Signed-off-by: Hideo Saito <saito@densan.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
We don't have any use for these machvec fixups anymore, kill them all
off and go with the generic instead.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables the SM501 drivers for the R2D board. Additional
work needs to be done to migrate off of the VoyagerGX cchip
code to make use of the rest of the mfd infrastructure.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
When I run a preemptive kernel-2.6.20 for SH7780, a created
kthread(pdflush) can not exit by do_exit() in kernel_thread_helper. I
think that the created kthread should have a room for 'struct pt_regs'
space on the stack top, because __switch_to() will refer to the space as
follows using 'regs = task_pt_regs(prev)' and next condition may be true.
Signed-off-by: Hideo Saito <saito@densan.co.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was a missing return in do_signal() that caused the saved
sigmask to be written back after having successfully delivered
the signal.
Signed-off-by: Ryusuke Sakato <sakato@hsdv.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This takes care of tearing down the UBC so it's not inadvertently
left configured at the next context switch time. Failure to do
this results in spurious SIGTRAPs in certain debug sequences.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the
beginning of the declaration specifiers in a declaration is an
obsolescent feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This tidies up some of the rts7751r2d mess and gets it booting
again. Update the defconfig, too.
Signed-off-by: Masayuki Hosokawa <hosokawa@ace-jp.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Neither of these have had any maintenance in years, and there's
no interest in keeping them straggling along. These have already
been slated for removal some time, so finally just get rid of them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Tidy up the R7780RP I/O mapping routines and switch the
pata_platform resources to IORESOURCE_MEM types, killing off
the useless port->addr conversion.
This fixes up R7780RP to boot after the recent devres conversion.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This ended up causing problems for older parts (particularly ones
using PTEA). Revert this for now, it can be added back in once it's
had some more testing.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This consolidates the various board heartbeat LED implementations,
used for strobing the load average across a LED bank. Those boards
not implementing a full bank can hook in via the LED class.
We leave the compat hook in the machvec for now until those non-banked
boards are able to migrate to the drivers/leds.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert some of the global flush users over to using the local variants
that don't need to use the global routines.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Rename the existing flush routines to local_ variants for use by
the IPI-backed global flush routines on SMP.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There are a lot of bogus cpu_data-> references that only end up working
for the boot CPU, convert these to current_cpu_data to fixup SMP.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously this was implemented using a global cache, cache
this per-CPU instead and bump up the number of context IDs to
match NR_CPUS.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This option needs a default - otherwise `make allmodconfig' gets
stuck in an infinite loop.
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This patch does the following:
- remove the make_ipr_irq stuff from dma-sh.c and replace it
with a simple channel<->irq mapping table.
- add DMTEx_IRQ constants for sh4 cpus
- fix sh7751 DMAE irq number
The SH7780 uses the same IRQs for DMA as other SH4 types, so
I put the constants on top of the dma.h file.
Other CPU types need to #define their own DMTEx_IRQ contants
in their appropriate header.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
handle_BUG() uses TRAPA_BUG_OPCODE which is only defined for
CONFIG_BUG, make sure it's not built when CONFIG_BUG=n.
Signed-off-by: Nobuhiro Iwamatsu <hemamu@t-base.ne.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Only SH-4 needs to set _PAGE_WT when using write-through caching,
don't attempt to set it on SH-3 where it ends up being a reserved
bit.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This converts the lazy dcache handling to the model described in
Documentation/cachetlb.txt and drops the ptep_get_and_clear() hacks
used for the aliasing dcaches on SH-4 and SH7705 in 32kB mode. As a
bonus, this slightly cuts down on the cache flushing frequency.
With that and the PTEA handling out of the way, the update_mmu_cache()
implementations can be consolidated, and we no longer have to worry
about which configuration the cache is in for the SH7705 case.
And finally, explicitly disable the lazy writeback on SMP (SH-4A).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There were a few more things that needed fixing up, namely THREAD_SIZE
and the TLB miss handler where certain PTRS_PER_PGD == PTRS_PER_PTE
assumptions were being made.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fixups for external IPR IRQs for the SE770x FPGA.
Signed-off-by: Nobuhiro Iwamatsu <hemamu@t-base.ne.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up shmin (and SH7706/SH7708) IPR support for some of the
recent API changes.
Signed-off-by: Takashi YOSHII <takasi-y@ops.dti.ne.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The iVDR clock enable bit happens to actually reside in a rather
different place than what is documented, so fix it up accordingly.
This fixes up SATA boot for some of the R7780RP boards that didn't
default-enable the clock in the loader.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This allows the baud rate for earlyprintk for sh4 without the
standard BIOS to be set via the command line. This uses the same
format as i386 and x86_64, which is:
earlyprintk=serial,ttySC1,38400
The second parameter (ttySC1 above) is usually the console device
name or the io address of the serial port. I allow that to be
specified but ignore it in order to keep the format the same as
i386/x86_64.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
-m2 doesn't end up working particularly well when we've got a constrained
toolchain target. Switch to the same semantics used by SH-4A to attempt
to get it right. Spotted by Alex Song <songqf9@yahoo.ca>.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This rips out most of the needlessly complicated sh_bios and kgdb
trap handling, and forces it all through a common fast dispatch path.
As more debug traps are inserted, it's important to keep them in sync
for all of the parts, not just SH-3/4.
As the SH-2 parts are unable to do traps in the >= 0x40 range, we
restrict the debug traps to the 0x30-0x3f range on all parts, and
also bump the kgdb breakpoint trap down in to this range (from 0xff
to 0x3c) so it's possible to use for nommu.
Optionally, this table can be padded out to catch spurious traps for
SH-3/4, but we don't do that yet..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Many struct file_operations in the kernel can be "const". Marking them const
moves these to the .rodata section, which avoids false sharing with potential
dirty data. In addition it'll catch accidental writes at compile time to
these shared resources.
[akpm@osdl.org: sparc64 fix]
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Update all arch/*/kernel/vmlinux.lds.S to not include space for initramfs
when CONFIG_BLK_DEV_INITRAMFS is not selected. This saves another 4 kbytes
on most platfoms (some reserve PAGE_SIZE for initramfs).
Signed-off-by: Jean-Paul Saman <jean-paul.saman@nxp.com>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
sh / sh64: Remove ZONE_DMA remains.
Both arches do not need ZONE_DMA
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'upstream' of git://ftp.linux-mips.org/pub/scm/upstream-apm:
[APM] SH: Convert to use shared APM emulation.
[APM] MIPS: Convert to use shared APM emulation.
[APM] ARM: Convert to use shared APM emulation.
[APM] Add shared version of APM emulation
This adds in support for the BUG() trap on SH-2.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This was inadvertently broken when the entry.S code split up,
restore the missing branch and get subsequent traps working
under debug again. This manifested itself as a lockup when
attempting to reload the VBR base.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH-2 and SH-2A need to use a different syscall base for the trapa
vector than the other parts, so fixup the logic in the kernel_execve()
case.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some time ago the schedule frame size changed and we failed to reflect
this in get_wchan() at the time. This first popped up as a problem on
SH7751R where schedule_frame ended up being unaligned and generating
an unaligned trap. This fixes it up again..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously we haven't been doing anything with verbose BUG() reporting,
and we've been relying on the oops path for handling BUG()'s, which is
rather sub-optimal.
This switches BUG handling to use a fixed trapa vector (#0x3e) where we
construct a small bug frame post trapa instruction to get the context
right. This also makes it trivial to wire up a DIE_BUG for the atomic
die chain, which we couldn't really do before.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This can use the generic routines, so kill off the board-specific ones.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This updates the SH7619 and SH7206 code for the IPR IRQ changes.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
gcc 4 for sh changes the names of some compiler intrinsic functions
and adds some additional ones. This patch adds the new ones, and
fixes up various module symbol resolution issues.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Register the RTC resources for the sh775x subtype so that the new
generic RTC support in drivers/rtc/rtc-sh.c will work.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a new defconfig for SE7619 and updates SE7206.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Convert SH to use generic ioremap_page_range()
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This facility provides three entry points:
ilog2() Log base 2 of unsigned long
ilog2_u32() Log base 2 of u32
ilog2_u64() Log base 2 of u64
These facilities can either be used inside functions on dynamic data:
int do_something(long q)
{
...;
y = ilog2(x)
...;
}
Or can be used to statically initialise global variables with constant values:
unsigned n = ilog2(27);
When performing static initialisation, the compiler will report "error:
initializer element is not constant" if asked to take a log of zero or of
something not reducible to a constant. They treat negative numbers as
unsigned.
When not dealing with a constant, they fall back to using fls() which permits
them to use arch-specific log calculation instructions - such as BSR on
x86/x86_64 or SCAN on FRV - if available.
[akpm@osdl.org: MMC fix]
Signed-off-by: David Howells <dhowells@redhat.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: David Howells <dhowells@redhat.com>
Cc: Wojtek Kaniewski <wojtekka@toxygen.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
After LOADER_TYPE && INITRD_START are true, the short if-condition
for INITRD_START can never be false.
Remove unused code from the else condition.
Signed-off-by: Henry Nestler <henry.ne@arcor.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The new shared APM emulation just like its ARM and MIPS predecessors uses
pm_suspend() which was only exported on SH. Move export to close to it's
definition where it really should be anyway.
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move process freezing functions from include/linux/sched.h to freezer.h, so
that modifications to the freezer or the kernel configuration don't require
recompiling just about everything.
[akpm@osdl.org: fix ueagle driver]
Signed-off-by: Nigel Cunningham <nigel@suspend2.net>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace all uses of kmem_cache_t with struct kmem_cache.
The patch was generated using the following script:
#!/bin/sh
#
# Replace one string by another in all the kernel sources.
#
set -e
for file in `find * -name "*.c" -o -name "*.h"|xargs grep -l $1`; do
quilt add $file
sed -e "1,\$s/$1/$2/g" $file >/tmp/$$
mv /tmp/$$ $file
quilt refresh
done
The script was run like this
sh replace kmem_cache_t "struct kmem_cache"
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
SLAB_KERNEL is an alias of GFP_KERNEL.
Signed-off-by: Christoph Lameter <clameter@sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Following up with the work on shared page table done by Dave McCracken. This
set of patch target shared page table for hugetlb memory only.
The shared page table is particular useful in the situation of large number of
independent processes sharing large shared memory segments. In the normal
page case, the amount of memory saved from process' page table is quite
significant. For hugetlb, the saving on page table memory is not the primary
objective (as hugetlb itself already cuts down page table overhead
significantly), instead, the purpose of using shared page table on hugetlb is
to allow faster TLB refill and smaller cache pollution upon TLB miss.
With PT sharing, pte entries are shared among hundreds of processes, the cache
consumption used by all the page table is smaller and in return, application
gets much higher cache hit ratio. One other effect is that cache hit ratio
with hardware page walker hitting on pte in cache will be higher and this
helps to reduce tlb miss latency. These two effects contribute to higher
application performance.
Signed-off-by: Ken Chen <kenneth.w.chen@intel.com>
Acked-by: Hugh Dickins <hugh@veritas.com>
Cc: Dave McCracken <dmccr@us.ibm.com>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: David Gibson <david@gibson.dropbear.id.au>
Cc: Adam Litke <agl@us.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: "David S. Miller" <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
The following moves the creation of IPR interupts into setup-7750.c
and updates a few other things to make it all work after the "Drop
CPU subtype IRQ headers" commit. It boots and runs fine on my titan
board.
- adds an ipr_idx to the ipr_data and uses a function in the subtype
code to calculate the address of the IPR registers
- adds a function to enable individual interrupt mode for externals
in the subtype code and calls that from the titan board code
instead of doing it directly.
- I changed the shift in the ipr_data to be the actual # of bits to
shift, instead of the numnber / 4 - made it easier to match with
the manual.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Since some header inclusion paths were cleaned up, compilation
broke. Add in the headers we need directly to build again.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds a platform device for the directly connected
CF interface on R7780RP boards, for use with the
pata_platform libata driver.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds basic NO_IDLE_HZ support to the SH timer API so timers
are able to wire it up. Taken from the ARM version, as it fit in
to our API with very few changes needed.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This syncs up the SH clock framework with the linux/clk.h API,
for which there were only some minor changes required, namely
the clk_get() dev_id and subsequent callsites.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Since all of the sys_timer sources currently do this on their own
within the ->get_offset() path, it's more sensible to just have
the caller take care of it when grabbing xtime_lock. Incidentally,
this is more in line with what others (ie, ARM) are doing already.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously this was using a static pgd shift in the reporting
code, simply flip this to PGDIR_SHIFT which does the right
thing depending on varying PTE magnitudes on the SH-X2 MMU.
While we're at it, and since it's been recently added, use
get_TTB() for fetching the TTB, rather than the open coded
instructions.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The end of the store queue bitmap is miscalculated when searching
for a free range in sq_remap(), missing the PAGE_SHIFT shift that's
done in sq_api_init(). This runs in to workloads where we can scan
beyond the end of the bitmap.
Spotted by Paul Jackson:
http://marc.theaimsgroup.com/?l=linux-kernel&m=116493191224097&w
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This makes the early printk support somewhat more flexible,
moving the port definition to a config option, and making the
port initialization configurable for sh-ipl+g users.
At the same time, this allows us to trivially wire up the
SH7780 SCIF0, so that's thrown in too more or less for free.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There were a number of places that made evil PAGE_SIZE == 4k
assumptions that ended up breaking when trying to play with
8k and 64k page sizes, this fixes those up.
The most significant change is the way we load THREAD_SIZE,
previously this was done via:
mov #(THREAD_SIZE >> 8), reg
shll8 reg
to avoid a memory access and allow the immediate load. With
a 64k PAGE_SIZE, we're out of range for the immediate load
size without resorting to special instructions available in
later ISAs (movi20s and so on). The "workaround" for this is
to bump up the shift to 10 and insert a shll2, which gives a
bit more flexibility while still being much cheaper than a
memory access.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
There was a clobber issue with the register we were saving
the stack in, so we switch to a register that we handle in
the clobber list properly already.
This also follows the x86 changes for allowing the softirq
checks from hardirq context.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This extends the SH DMA API for allowing handling of DMA
channels based off of their respective capabilities.
A couple of functions are added to the existing API,
the core bits are register_chan_caps() for registering
channel capabilities, and request_dma_bycap() for fetching
a channel dynamically based off of a capability set.
Signed-off-by: Mark Glaisher <mark.glaisher@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Pass along the dev_id from request_dma() all the way down,
rather than inserting an artificial name relating to the TEI
line that we were doing before.
This makes the line a bit less obvious, but dev_id is the proper
behaviour for this regardless.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously we linked in the ISA DMA wrapper unconditionally.
As there are very few users of this, it's better to make it
conditional.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Handle the case where no registered DMACs exist somewhat more
gracefully. While we're at it, check for sysdev_create_file()
failing.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The implementation of system call tracing in the kernel has a
couple of ordering problems:
- the validity of the system call number is checked before
calling out to system call tracing code, and should be
done after
- the system call number used when tracing is the one the
system call was invoked with, while the system call tracing
code can legitimatly change the call number (for example
strace permutes fork into clone)
This patch fixes both of these problems, and also reoders the
code slightly to make the direct path through the code the
common case.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Handle simple TLB miss faults which can be resolved completely
from the page table in assembler.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for a generic push switch framework. Adaptable for
various switches, including GPIO switches and the push switches commonly
found on Renesas debug boards.
This allows switch states to be trivially reported through sysfs.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove extra bits from the pmd structure and store a kernel logical
address rather than a physical address. This allows it to be directly
dereferenced. Another piece of wierdness inherited from x86.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add TTB accessor functions and give it a sensible default
value. We will use this later for optimizing the fault
path.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Remove the previous saving of fault codes into the thread_struct
as they are never used, and appeared to be inherited from x86.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up the kernel for gcc4. The existing exception handlers
needed some wrapping for pt_regs access, acessing the registers
via a RELOC_HIDE() pointer.
The strcpy() issues popped up here too, so add -ffreestanding and
kill off the symbol export.
Signed-off-by: Stuart Menefy <stuart.menefy@st.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Previously big endian was simply assumed if little endian was
not set, which led to some cflags ordering issues. There's not
much point to not having a big endian option, so shove one in
a choice and wire it up in the Makefile.
This lets us clean up some of the cflags ordering while we're
at it.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds some preliminary support for the SH-X2 MMU, used by
newer SH-4A parts (particularly SH7785).
This MMU implements a 'compat' mode with SH-X MMUs and an
'extended' mode for SH-X2 extended features. Extended features
include additional page sizes (8kB, 4MB, 64MB), as well as the
addition of page execute permissions.
The extended mode attributes are placed in a second data array,
which requires us to switch to 64-bit PTEs when in X2 mode.
With the addition of the exec perms, we also overhaul the mmap
prots somewhat, now that it's possible to handle them more
intelligently.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This drops the various IRQ headers that were floating around
and primarily providing hardcoded IRQ definitions for the
various CPU subtypes. This quickly got to be an unmaintainable
mess, made even more evident by the subtle breakage introduced
by the SH-2 and SH-2A changes.
Now that subtypes are able to register IRQ maps directly, just
rip all of the headers out.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
All of the various CPU subtypes currently hardcode TIMER_IRQ,
switch this to a config option in the few places we need this.
This allows further removal of hardcoded IRQ headers..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the Solution Engine 7206 and 7619.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This splits out common bits from the existing exception handler for
use between SH-2/SH-2A and SH-3/4, and adds support for the SH-2/2A
exceptions.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
SH-2A has special division hardware as opposed to a full-fledged FPU,
wire up the exception handlers for this.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements initial support for the SH7206 (SH-2A) and SH7619
(SH-2) MMU-less CPUs.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix various Kconfig typos.
Signed-off-by: Matt LaPlante <kernel1@cyberdogtech.com>
Acked-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Small defconfig update for titan for 2.6.19-rc3, adding SH-RTC.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The conversion from IPR-IRQ to IRQ-chip resulted in the
ipr data being allocated in a local variable in
make_ipr_irq - breaking anything using IPR interrupts.
This changes all of the callers of make_ipr_irq to
allocate a static structure containing the IPR data which
is then passed to make_ipr_irq. This removes the need for
make_ipr_irq to allocate any additional space for the IPR
information.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add a vmlinux.lds.h helper macro for defining the eight-level initcall table,
teach all the architectures to use it.
This is a prerequisite for a patch which performs initcall synchronisation for
multithreaded-probing.
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
[ Added AVR32 as well ]
Signed-off-by: Haavard Skinnemoen <hskinnemoen@atmel.com>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Currently the INTC2 code contains a fixed IRQ table that it
iterates through to set the handler type, we move this in to
the CPU subtype setup code instead and allow for submitting
the table that way.
This drops the ST40 tables, as nothing has been happening
with those processors, while converting the only existing
users to use the new table directly (SH7760 and SH7780).
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
handle_irq_name() and set_irq_chip_and_handler() disappeared,
update for desc->name and set_irq_chip_and_handler_name() use.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With the recent change ripping out interrupt_table, explicit
padding of the table was missing, causing bad things to happen
when manually inserting handlers in to the table. This problem
particularly showed up in relation to do_fpu_state_restore()
which was inserted quite deeply in to the table and ended up
scribbling over a slab object.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now with the ide.h mess sorted out, most of these boards
don't need their own directory. Move the headers out, and
update the driver paths.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This splits out some of the previous show_stack() implementation which
was mostly doing the show_trace() work without actually dumping any of
the stack contents. This now gets split in to two sections, where we
do the fetching of the stack pointer and subsequent stack dumping in
show_stack(), while moving the call trace in to show_trace().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Kill off interrupt_table for all of the CPU subtypes, we now
default in to stepping in to do_IRQ() for _all_ IRQ exceptions
and counting the spurious ones, rather than simply flipping on
the ones we cared about. This and enabling the IRQ by default
automatically has already uncovered a couple of bugs and IRQs
that weren't being caught, as well as some that are being
generated far too often (SCI Tx Data Empty, for example).
The general rationale is to use a marker for interrupt exceptions,
test for it in the handle_exception() path, and skip out to
do_IRQ() if it's found. Everything else follows the same behaviour
of finding the cached EXPEVT value in r2/r2_bank, we just rip out
the INTEVT read from entry.S entirely (except for in the kGDB NMI
case, which is another matter).
Note that while this changes the do_IRQ() semantics regarding r4
handling, they were fundamentally broken anyways (relying entirely
on r2_bank for the cached code). With this, we do the INTEVT read
from do_IRQ() itself (in the CONFIG_CPU_HAS_INTEVT case), or fall
back on r4 for the muxed IRQ number, which should also be closer
to what SH-2 and SH-2A want anyways.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Now that we've started accounting for spurious IRQs, change the
logic somewhat so that we have a better chance of catching them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Fix a problem uncovered by the recent change to always check the
arguments to pr_debug. The sh7751 was using the wrong name for the
PCI IO base address.
Signed-off-by: Jamie Lenehan <lenehan@twibble.org>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
At the moment we wrap GENERIC_TIME around our existing timer API.
As boards start providing their own clocksources, they're able to
select GENERIC_TIME accordingly and optimize out most of the timer
API.
Once the current timers have been reworked as proper clocksource
drivers, the rest of the place holders for the timer API can go
away and we can flip on GENERIC_TIME unconditionally.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Many files include the filename at the beginning, serveral used a wrong one.
Signed-off-by: Uwe Zeisberger <Uwe_Zeisberger@digi.com>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
This adds the new kernel_execve function on all architectures that were using
_syscall3() to implement execve.
The implementation uses code from the _syscall3 macros provided in the
unistd.h header file. I don't have cross-compilers for any of these
architectures, so the patch is untested with the exception of i386.
Most architectures can probably implement this in a nicer way in assembly or
by combining it with the sys_execve implementation itself, but this should do
it for now.
[bunk@stusta.de: m68knommu build fix]
[markh@osdl.org: build fix]
[bero@arklinux.org: build fix]
[ralf@linux-mips.org: mips fix]
[schwidefsky@de.ibm.com: s390 fix]
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Bernhard Rosenkraenzer <bero@arklinux.org>
Signed-off-by: Mark Haverkamp <markh@osdl.org>
Signed-off-by: Adrian Bunk <bunk@stusta.de>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
In some places, particularly drivers and __init code, the init utsns is the
appropriate one to use. This patch replaces those with a the init_utsname
helper.
Changes: Removed several uses of init_utsname(). Hope I picked all the
right ones in net/ipv4/ipconfig.c. These are now changed to
utsname() (the per-process namespace utsname) in the previous
patch (2/7)
[akpm@osdl.org: CIFS fix]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Cc: Serge Hallyn <serue@us.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Replace references to system_utsname to the per-process uts namespace
where appropriate. This includes things like uname.
Changes: Per Eric Biederman's comments, use the per-process uts namespace
for ELF_PLATFORM, sunrpc, and parts of net/ipv4/ipconfig.c
[jdike@addtoit.com: UML fix]
[clg@fr.ibm.com: cleanup]
[akpm@osdl.org: build fix]
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Signed-off-by: Cedric Le Goater <clg@fr.ibm.com>
Cc: Jeff Dike <jdike@addtoit.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Move the init_nsproxy definition out of arch/ into kernel/nsproxy.c. This
avoids all arches having to be updated. Compiles and boots on s390.
Signed-off-by: Serge E. Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This patch adds a nsproxy structure to the task struct. Later patches will
move the fs namespace pointer into this structure, and introduce a new utsname
namespace into the nsproxy.
The vserver and openvz functionality, then, would be implemented in large part
by virtualizing/isolating more and more resources into namespaces, each
contained in the nsproxy.
[akpm@osdl.org: build fix]
Signed-off-by: Serge Hallyn <serue@us.ibm.com>
Cc: Kirill Korotaev <dev@openvz.org>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Herbert Poetzl <herbert@13thfloor.at>
Cc: Andrey Savochkin <saw@sw.ru>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
cpumask: ensure that the cpu_online_map and cpu_possible_map bitmasks, and
hence all the macros in <linux/cpumask.h> that require them, are available to
modules for all supported combinations of architecture and CONFIG_SMP.
Signed-off-by: Greg Banks <gnb@melbourne.sgi.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
With 2.6.18-rc4-mm2, now wall_jiffies will always be the same as jiffies.
So we can kill wall_jiffies completely.
This is just a cleanup and logically should not change any real behavior
except for one thing: RTC updating code in (old) ppc and xtensa use a
condition "jiffies - wall_jiffies == 1". This condition is never met so I
suppose it is just a bug. I just remove that condition only instead of
kill the whole "if" block.
[heiko.carstens@de.ibm.com: s390 build fix and cleanup]
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Cc: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Pass ticks to do_timer() and update_times(), and adjust x86_64 and s390
timer interrupt handler with this change.
Currently update_times() calculates ticks by "jiffies - wall_jiffies", but
callers of do_timer() should know how many ticks to update. Passing ticks
get rid of this redundant calculation. Also there are another redundancy
pointed out by Martin Schwidefsky.
This cleanup make a barrier added by
5aee405c66 needless. So this patch removes
it.
As a bonus, this cleanup make wall_jiffies can be removed easily, since now
wall_jiffies is always synced with jiffies. (This patch does not really
remove wall_jiffies. It would be another cleanup patch)
Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: "Eric W. Biederman" <ebiederm@xmission.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: john stultz <johnstul@us.ibm.com>
Cc: Andi Kleen <ak@muc.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Richard Henderson <rth@twiddle.net>
Cc: Ivan Kokshaysky <ink@jurassic.park.msu.ru>
Acked-by: Russell King <rmk@arm.linux.org.uk>
Cc: Ian Molton <spyro@f2s.com>
Cc: Mikael Starvik <starvik@axis.com>
Acked-by: David Howells <dhowells@redhat.com>
Cc: Yoshinori Sato <ysato@users.sourceforge.jp>
Cc: Hirokazu Takata <takata.hirokazu@renesas.com>
Acked-by: Ralf Baechle <ralf@linux-mips.org>
Cc: Kyle McMartin <kyle@mcmartin.ca>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Richard Curnow <rc@rc0.org.uk>
Cc: William Lee Irwin III <wli@holomorphy.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jeff Dike <jdike@addtoit.com>
Cc: Paolo 'Blaisorblade' Giarrusso <blaisorblade@yahoo.it>
Cc: Miles Bader <uclinux-v850@lsi.nec.co.jp>
Cc: Chris Zankel <chris@zankel.net>
Acked-by: "Luck, Tony" <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Roman Zippel <zippel@linux-m68k.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
This is an updated version of Eric Biederman's is_init() patch.
(http://lkml.org/lkml/2006/2/6/280). It applies cleanly to 2.6.18-rc3 and
replaces a few more instances of ->pid == 1 with is_init().
Further, is_init() checks pid and thus removes dependency on Eric's other
patches for now.
Eric's original description:
There are a lot of places in the kernel where we test for init
because we give it special properties. Most significantly init
must not die. This results in code all over the kernel test
->pid == 1.
Introduce is_init to capture this case.
With multiple pid spaces for all of the cases affected we are
looking for only the first process on the system, not some other
process that has pid == 1.
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@us.ibm.com>
Cc: Dave Hansen <haveblue@us.ibm.com>
Cc: Serge Hallyn <serue@us.ibm.com>
Cc: Cedric Le Goater <clg@fr.ibm.com>
Cc: <lxc-devel@lists.sourceforge.net>
Acked-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
Make PROT_WRITE imply PROT_READ for a number of architectures which don't
support write only in hardware.
While looking at this, I noticed that some architectures which do not
support write only mappings already take the exact same approach. For
example, in arch/alpha/mm/fault.c:
"
if (cause < 0) {
if (!(vma->vm_flags & VM_EXEC))
goto bad_area;
} else if (!cause) {
/* Allow reads even for write-only mappings */
if (!(vma->vm_flags & (VM_READ | VM_WRITE)))
goto bad_area;
} else {
if (!(vma->vm_flags & VM_WRITE))
goto bad_area;
}
"
Thus, this patch brings other architectures which do not support write only
mappings in-line and consistent with the rest. I've verified the patch on
ia64, x86_64 and x86.
Additional discussion:
Several architectures, including x86, can not support write-only mappings.
The pte for x86 reserves a single bit for protection and its two states are
read only or read/write. Thus, write only is not supported in h/w.
Currently, if i 'mmap' a page write-only, the first read attempt on that page
creates a page fault and will SEGV. That check is enforced in
arch/blah/mm/fault.c. However, if i first write that page it will fault in
and the pte will be set to read/write. Thus, any subsequent reads to the page
will succeed. It is this inconsistency in behavior that this patch is
attempting to address. Furthermore, if the page is swapped out, and then
brought back the first read will also cause a SEGV. Thus, any arbitrary read
on a page can potentially result in a SEGV.
According to the SuSv3 spec, "if the application requests only PROT_WRITE, the
implementation may also allow read access." Also as mentioned, some
archtectures, such as alpha, shown above already take the approach that i am
suggesting.
The counter-argument to this raised by Arjan, is that the kernel is enforcing
the write only mapping the best it can given the h/w limitations. This is
true, however Alan Cox, and myself would argue that the inconsitency in
behavior, that is applications can sometimes work/sometimes fails is highly
undesireable. If you read through the thread, i think people, came to an
agreement on the last patch i posted, as nobody has objected to it...
Signed-off-by: Jason Baron <jbaron@redhat.com>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: "Luck, Tony" <tony.luck@intel.com>
Cc: Hugh Dickins <hugh@veritas.com>
Cc: Roman Zippel <zippel@linux-m68k.org>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Andi Kleen <ak@muc.de>
Acked-by: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Arjan van de Ven <arjan@linux.intel.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Kazumoto Kojima <kkojima@rr.iij4u.or.jp>
Cc: Ian Molton <spyro@f2s.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
IRQs disabling in flush_cache_4096 for cache purge. Under certain
workloads we would get an IRQ in the middle of a purge operation,
and the cachelines would remain in an inconsistent state, leading
to occasional stack corruption.
Signed-off-by: Takeo Takahashi <takahashi.takeo@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Set the SHM alignment at runtime, based off of probed cache desc.
Optimize get_unmapped_area() to only colour align shared mappings.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This implements initial support for the vsyscall page on SH.
At the moment we leave it configurable due to having nommu
to support from the same code base. We hook it up for the
signal trampoline return at present, with more to be added
later, once uClibc catches up.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
flush_cache_mm() wraps in to flush_cache_all(), which is rather
excessive given that the number of PTEs within the specified context
are generally quite low. Optimize for walking the mm's VMA list and
selectively flushing the VMA ranges from the dcache. Invalidate the
icache only if a VMA sets VM_EXEC.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Figure out the cache desc entry_mask at runtime, and remove
hard-coded assumption about the cacheline size.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This enables support for 4K stacks on SH.
Currently this depends on DEBUG_KERNEL, but likely all boards
will switch to this as the default in the future.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some more machvec overhauling and setup code cleanup. Kill off
get_system_type() and platform_setup(), we can do these both
through the machvec. While we're add it, kill off more useless
mach.c's and drop some legacy cruft from setup.c.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
The generic hardirq layer already takes care of a lot of the
appropriate locking and disabling for us, no need to duplicate
it in the handlers..
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
None of these have been maintained in years, and no one seems to
be interested in doing so, so just get rid of them.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds support for the aforementioned CPU subtypes, and cleans
up some build issues encountered as a result.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds some simple setup code for most of the CPU subtypes,
primarily simple platform device registration.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes up some of the various outstanding nommu bugs on
SH.
Signed-off-by: Yoshinori Sato <ysato@users.sourceforge.jp>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
nommu needs to be able to shift PAGE_OFFSET, so we switch it to a
non-user-visible CONFIG_PAGE_OFFSET and use that in the few places
where it matters.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Drop TIF_USERSPACE and add addr_limit to the thread_info struct.
Subsequently, use that for address checking in strnlen_user() to
ward off bogus -EFAULTs.
Make __strnlen_user() return 0 on exception, rather than -EFAULT.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This fixes a long-standing FIXME for G2 DMA, where we finally
wire up the IRQ handler and allow for sampling remaining bytes
while in-flight.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This adds the VoyagerGX UART to the RTS7751R2D setup
code, and cleans up a few build issues.
Signed-off-by: Manuel Lauss <mano@roarinelk.homelinux.net>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Inhibit mapping through page tables in __ioremap() for PCI memory
apertures on SH7751 and SH7780-style PCI controllers, translation is
not possible for these areas. For other users that map a small window
in P1/P2 space, ioremap() traps that already, and should never make
it to __ioremap().
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This cleans up quite a lot of the PCI mess that we
currently have, and attempts to consolidate the
duplication in the SH7780 and SH7751 PCI controllers.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Some kgdb cleanup. Move hexchars/highhex/lowhex to the header, so it can
be reused by sh-sci. Also drop silly ctrl_inl/outl() overloading being
done by the kgdb stub.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Paul Mundt