Pull HID subsystem updates from Jiri Kosina:
"Apart from various driver updates and added support for a number of
new devices (mostly multitouch ones, but not limited to), there is one
change that is worth pointing out explicitly: creation of HID device
groups and proper autoloading of hid-multitouch, implemented by Henrik
Rydberg."
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid: (50 commits)
HID: wacom: fix build breakage without CONFIG_LEDS_CLASS
HID: waltop: Extend barrel button fix
HID: hyperv: Set the hid drvdata correctly
HID: wacom: Unify speed setting
HID: wacom: Add speed setting for Intuos4 WL
HID: wacom: Move Graphire raport header check.
HID: uclogic: Add support for UC-Logic TWHL850
HID: explain the signed/unsigned handling in hid_add_field()
HID: handle logical min/max signedness properly in parser
HID: logitech: read all 32 bits of report type bitfield
HID: wacom: Add LED selector control for Wacom Intuos4 WL
HID: hid-multitouch: fix wrong protocol detection
HID: wiimote: Fix IR data parser
HID: wacom: Add tilt reporting for Intuos4 WL
HID: multitouch: MT interface matching for Baanto
HID: hid-multitouch: Only match MT interfaces
HID: Create a common generic driver
HID: hid-multitouch: Switch to device groups
HID: Create a generic device group
HID: Allow bus wildcard matching
...
Most HID drivers do not need to know what bus driver is in use.
A generic group driver can drive any hid device, and the device
list should not need to be duplicated for each new bus.
This patch adds wildcard matching to the HID bus, simplifying device
list handling for group drivers.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
HID devices are only partially presented to userland. Hotplugged
devices emit events containing a modalias based on the basic bus,
vendor and product entities. However, in practise a hid device can
depend on details such as a single usb interface or a particular item
in a report descriptor.
This patch adds a device group to the hid device id, and broadcasts it
using uevent and the device modalias. The module alias generation is
modified to match. As a consequence, a device with a non-zero group
will be processed by the corresponding group driver instead of by the
generic hid driver.
Signed-off-by: Henrik Rydberg <rydberg@euromail.se>
Acked-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The symbol table on x86-64 starts to have entries that have names
like:
_GLOBAL__sub_I_65535_0___mod_x86cpu_device_table
They are of type STT_FUNCTION and this one had a length of 18. This
matched the device ID validation logic and it barfed because the
length did not meet the device type's criteria.
--------------------
FATAL: arch/x86/crypto/aesni-intel: sizeof(struct x86cpu_device_id)=16 is not a modulo of the size of section __mod_x86cpu_device_table=18.
Fix definition of struct x86cpu_device_id in mod_devicetable.h
--------------------
These are some kind of compiler tool internal stuff being emitted and
not something we want to inspect in modpost's device ID table
validation code.
So skip the symbol if it is not of type STT_OBJECT.
Signed-off-by: David S. Miller <davem@davemloft.net>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
commit e49ce14150 breaks cross compiling
the linux kernel on darwin hosts.
This fix introduce some minimal glue to adopt linker section handling
for darwin hosts.
Signed-off-by: Andreas Bießmann <andreas@biessmann.de>
CC: Rusty Russell <rusty@rustcorp.com.au>
CC: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
CC: Jochen Friedrich <jochen@scram.de>
CC: Samuel Ortiz <sameo@linux.intel.com>
CC: "K. Y. Srinivasan" <kys@microsoft.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Tested-by: Bernhard Walle <bernhard@bwalle.de>
Handling of isapnp module aliases was broken by commit
626596e295 by changing "isapnp" string to "isa".
The code was then modified by commit
e49ce14150 but this bug remained.
Change the string back to "isapnp".
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We currently include commas on both sides of the feature ID in a
modalias, but this prevents the lowest numbered feature of a CPU from
being matched. Since all feature IDs have the same length, we do not
need to worry about substring matches, so omit commas from the
modalias entirely.
Avoid generating multiple adjacent wildcards when there is no
feature ID to match.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Thomas Renninger <trenn@suse.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
This was done to resolve a merge and build problem with the
drivers/acpi/processor_driver.c file.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
There's a growing number of drivers that support a specific x86 feature
or CPU. Currently loading these drivers currently on a generic
distribution requires various driver specific hacks and it often
doesn't work.
This patch adds auto probing for drivers based on the x86 cpuid
information, in particular based on vendor/family/model number
and also based on CPUID feature bits.
For example a common issue is not loading the SSE 4.2 accelerated
CRC module: this can significantly lower the performance of BTRFS
which relies on fast CRC.
Another issue is loading the right CPUFREQ driver for the current CPU.
Currently distributions often try all all possible driver until
one sticks, which is not really a good way to do this.
It works with existing udev without any changes. The code
exports the x86 information as a generic string in sysfs
that can be matched by udev's pattern matching.
This scheme does not support numeric ranges, so if you want to
handle e.g. ranges of model numbers they have to be encoded
in ASCII or simply all models or families listed. Fixing
that would require changing udev.
Another issue is that udev will happily load all drivers that match,
there is currently no nice way to stop a specific driver from
being loaded if it's not needed (e.g. if you don't need fast CRC)
But there are not that many cpu specific drivers around and they're
all not that bloated, so this isn't a particularly serious issue.
Originally this patch added the modalias to the normal cpu
sysdevs. However sysdevs don't have all the infrastructure
needed for udev, so it couldn't really autoload drivers.
This patch instead adds the CPU modaliases to the cpuid devices,
which are real devices with full support for udev. This implies
that the cpuid driver has to be loaded to use this.
This patch just adds infrastructure, some driver conversions
in followups.
Thanks to Kay for helping with some sysfs magic.
v2: Constifcation, some updates
v4: (trenn@suse.de):
- Use kzalloc instead of kmalloc to terminate modalias buffer
- Use uppercase hex values to match correctly against hex values containing
letters
Cc: Dave Jones <davej@redhat.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Jen Axboe <axboe@kernel.dk>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Huang Ying <ying.huang@intel.com>
Cc: Len Brown <lenb@kernel.org>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Thomas Renninger <trenn@suse.de>
Acked-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This reverts commit 5dd7bf59e0.
Conflicts:
scripts/mod/file2alias.c
This change is wrong on many levels. First and foremost, it causes a
regression. On boot on Assabet, which this patch gives a codec id of
'ucb1x00', it gives:
ucb1x00 ID not found: 1005
0x1005 is a valid ID for the UCB1300 device.
Secondly, this patch is way over the top in terms of complexity. The
only device which has been seen to be connected with this MCP code is
the UCB1x00 (UCB1200, UCB1300 etc) devices, and they all use the same
driver. Adding a match table, requiring the codec string to match the
hardware ID read out of the ID register, etc is completely over the top
when we can just read the hardware ID register.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQIcBAABAgAGBQJPD2aFAAoJENkgDmzRrbjxNzsQAIeYbbrXYLjr6kQzUSngj/eC
FzjaTEfYTQIeuQCFJHcHthyc5lXV4sQbo3jOezW+Bp5yuDJL2aWIHesSfWZe7imu
zQdM4VshOYdAmUR9Q0AW5zhB8Smbs7/AyABiF2jm4p0ZPOuyMDSlei9sjvE9Vjvt
B7g5ht7L6kz0JbDnwwy0u5gs+tEitwpXYId9Y4ysZIBzIbL0qkPX8veOddGTMy0N
8xhWXaKtufpjvxFD2ORLDsw3AkoF1xXSNuFd/5nzCNpbeE7TW931jfkPoqJumuAO
7GLxcU9kKYl+IICobC6wBtsj/RrB7w+cBXMvPGwdBliam1qaRhUcJZi5FLM/Ha5d
2A9QDYNUpoXiO8JbPXrV9Z+Y0+Co8RilsQj7R/rjZh6AbbYCWt9nxzx2Svl/RfTr
xfiimHuB2P3rHjOvpCXULwOOuE5c8MzPuWncpdjiD3uGXOY/aY+X1m+if/quJw9D
grPlKL0+YiRakEYUeGG4M77KCqyKFZaF7L7UQPbqfZcj8V/9AW3/7U5I/B9RlAjs
idsr4fcf5s0N+oKUyTCW1ncpUDQNiwbU2NyJQqeu1ZxaRGj72AgyvsaNeyIPDyK+
f6x95Bi7i8KLjXc9Z1KvJwh2Nxt25gNUiTYVha/9H2NpJGd1cfI15kTOGXrgddVv
1pvuGcJDZwYiwfiXr3FL
=HHrh
-----END PGP SIGNATURE-----
Merge tag 'for-linus' of git://github.com/rustyrussell/linux
Autogenerated GPG tag for Rusty D1ADB8F1: 15EE 8D6C AB0E 7F0C F999 BFCB D920 0E6C D1AD B8F1
* tag 'for-linus' of git://github.com/rustyrussell/linux:
module_param: check that bool parameters really are bool.
intelfbdrv.c: bailearly is an int module_param
paride/pcd: fix bool verbose module parameter.
module_param: make bool parameters really bool (drivers & misc)
module_param: make bool parameters really bool (arch)
module_param: make bool parameters really bool (core code)
kernel/async: remove redundant declaration.
printk: fix unnecessary module_param_name.
lirc_parallel: fix module parameter description.
module_param: avoid bool abuse, add bint for special cases.
module_param: check type correctness for module_param_array
modpost: use linker section to generate table.
modpost: use a table rather than a giant if/else statement.
modules: sysfs - export: taint, coresize, initsize
kernel/params: replace DEBUGP with pr_debug
module: replace DEBUGP with pr_debug
module: struct module_ref should contains long fields
module: Fix performance regression on modules with large symbol tables
module: Add comments describing how the "strmap" logic works
Fix up conflicts in scripts/mod/file2alias.c due to the new linker-
generated table approach to adding __mod_*_device_table entries. The
ARM sa11x0 mcp bus needed to be converted to that too.
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (59 commits)
rtc: max8925: Add function to work as wakeup source
mfd: Add pm ops to max8925
mfd: Convert aat2870 to dev_pm_ops
mfd: Still check other interrupts if we get a wm831x touchscreen IRQ
mfd: Introduce missing kfree in 88pm860x probe routine
mfd: Add S5M series configuration
mfd: Add s5m series irq driver
mfd: Add S5M core driver
mfd: Improve mc13xxx dt binding document
mfd: Fix stmpe section mismatch
mfd: Fix stmpe build warning
mfd: Fix STMPE I2c build failure
mfd: Constify aat2870-core i2c_device_id table
gpio: Add support for stmpe variant 801
mfd: Add support for stmpe variant 801
mfd: Add support for stmpe variant 610
mfd: Add support for STMPE SPI interface
mfd: Separate out STMPE controller and interface specific code
misc: Remove max8997-muic sysfs attributes
mfd: Remove unused wm831x_irq_data_to_mask_reg()
...
Fix up trivial conflict in drivers/leds/Kconfig due to addition of
LEDS_MAX8997 and LEDS_TCA6507 next to each other.
This means (most) future busses need only have one hunk in their
patch. Also took the opportunity to check that function matches the
type.
Again, inspired by Alessandro's patch series.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alessandro Rubini <rubini@gnudd.com>
We look for symbols of form __mod_<busname>_device_table, and for all
but three cases we use a standard interation function (do_table) to
walk over the contents and dump out the aliases.
Alessandro Rubini did this first, I just repainted the bikeshed a bit.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Cc: Alessandro Rubini <rubini@gnudd.com>
This patch adds the necessary support in file2alias.c to define
suitable aliases based on the amba_id table in AMBA driver modules.
This should be sufficient to allow such modules to be auto-loaded
via udev. The AMBA bus driver's uevent hotplug code is also
modified to pass an approriate MODALIAS string in the event.
For simplicity, the AMBA ID is treated an an opaque 32-bit numeber.
Module alises use patterns as appropriate to describe the value-
mask pairs described in the driver's amba_id list.
The proposed alias format is (extended regex):
^amba:d(HEX){8}$
Where HEX is a single upper-case HEX digit or a pattern (? or []
expression) matching a single upper-case HEX digit, as expected by
udev.
"d" is short for "device", following existing alias naming
conventions for other device types. This adds some flexibility for
unambiguously extending the alias format in the future by adding
additional leading and trailing fields, if this turns out to be
necessary.
Signed-off-by: Dave Martin <dave.martin@linaro.org>
Acked-by: Pawel Moll <pawel.moll@arm.com>
When I added the driver_data field to hv_vmbus_device_id, I forgot to
take into the account how the alias was created, so it would append the
kernel pointer to the end of the alias, which is not correct.
This changes how the hv_vmbus_device_id alias is created to proper
account for the driver_data field. As no module yet uses this alias, it
is safe to fix this up at this point in the commit stream.
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Broadcom has released cards based on a new AMBA-based bus type. From a
programming point of view, this new bus type differs from AMBA and does
not use AMBA common registers. It also differs enough from SSB. We
decided that a new bus driver is needed to keep the code clean.
In its current form, the driver detects devices present on the bus and
registers them in the system. It allows registering BCMA drivers for
specified bus devices and provides them basic operations. The bus driver
itself includes two important bus managing drivers: ChipCommon core
driver and PCI(c) core driver. They are early used to allow correct
initialization.
Currently code is limited to supporting buses on PCI(e) devices, however
the driver is designed to be used also on other hosts. The host
abstraction layer is implemented and already used for PCI(e).
Support for PCI(e) hosts is working and seems to be stable (access to
80211 core was tested successfully on a few devices). We can still
optimize it by using some fixed windows, but this can be done later
without affecting any external code. Windows are just ranges in MMIO
used for accessing cores on the bus.
Cc: Greg KH <greg@kroah.com>
Cc: Michael Büsch <mb@bu3sch.de>
Cc: Larry Finger <Larry.Finger@lwfinger.net>
Cc: George Kashperko <george@znau.edu.ua>
Cc: Arend van Spriel <arend@broadcom.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Andy Botting <andy@andybotting.com>
Cc: linuxdriverproject <devel@linuxdriverproject.org>
Cc: linux-kernel@vger.kernel.org <linux-kernel@vger.kernel.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch makes modpost able to process object files with more than
64k sections. Needed for huge kernel builds (allyesconfig, for example)
with -ffunction-sections. 64k sections handling is covered, for example,
by this document:
"IA-64 gABI Proposal 74: Section Indexes"
http://www.codesourcery.com/public/cxx-abi/abi/prop-74-sindex.html
Signed-off-by: Denys Vlasenko <vda.linux@googlemail.com>
Signed-off-by: Anders Kaseorg <andersk@mit.edu>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: Andi Kleen <andi@firstfloor.org>
Signed-off-by: Michal Marek <mmarek@suse.cz>
* 'modules' of git://git.kernel.org/pub/scm/linux/kernel/git/rusty/linux-2.6-for-linus:
module: drop the lock while waiting for module to complete initialization.
MODULE_DEVICE_TABLE(isapnp, ...) does nothing
hisax_fcpcipnp: fix broken isapnp device table.
isapnp: move definitions to mod_devicetable.h so file2alias can reach them.
On Monday 23 November 2009 04:29:53 Rusty Russell wrote:
> On Mon, 23 Nov 2009 07:31:57 am Ondrej Zary wrote:
> > The problem is that
> > scripts/mod/file2alias.c simply ignores isapnp.
>
> AFAICT it always has, and noone has complained until now. Perhaps
> something was still reading /lib/modules/`uname -r`/modules.isapnpmap?
The patch below works fine (at least with Debian). It needs your first
patch that moves the definitions to mod_devicetable.h. Verified that
aliases for these modules are generated correctly:
drivers/media/radio/radio-sf16fmi.c
drivers/net/ne.c
drivers/net/3c515.c
drivers/net/smc-ultra.c
drivers/pcmcia/i82365.c
drivers/scsi/aha1542.c
drivers/scsi/aha152x.c
drivers/scsi/sym53c416.c
drivers/scsi/g_NCR5380.c
Tested with RTL8019AS (ne), AVA-1505AE (aha152x) and dtc436e (g_NCR5380)
cards - they now work automatically.
Generate pnp:d aliases for isapnp_device_tables. This allows udev to load
these modules automatically.
Signed-off-by: Ondrej Zary <linux@rainbow-software.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We don't use the normal hotplug mechanism because it doesn't work. It will
load the module some time after the device appears, but that's not good
enough for us -- we need the driver loaded _immediately_ because otherwise
the NIC driver may just abort and then the phy 'device' goes away.
[bwh: s/phy/mdio/ in module alias, kerneldoc for struct mdio_device_id]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Acked-by: Andy Fleming <afleming@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The sym_is() compares a symbol in an attempt to automatically skip symbol
prefixes. It does this first by searching the real symbol with the normal
unprefixed symbol. But then it uses the length of the original symbol to
check the end of the substring instead of the length of the symbol it is
looking for. On non-prefixed arches, this is effectively the same thing,
so there is no problem. On prefixed-arches, since this is exceeds by just
one byte, a crash is rare and it is usually a NUL byte anyways. But every
once in a blue moon, you get the right page alignment and it segfaults.
For example, on the Blackfin arch, sym_is() will be called with the real
symbol "___mod_usb_device_table" as "symbol" when looking for the normal
symbol "__mod_usb_device_table" as "name". The substring will thus return
one byte into "symbol" and store it into "match". But then "match" will
be indexed with the length of "symbol" instead of "name" and so we will
exceed the storage. i.e. the code ends up doing:
char foo[] = "abc"; return foo[strlen(foo)+1] == '\0';
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch fixes a bug when incrementing/decrementing on a BCD formatted
integer (i.e. 0x09++ should be 0x10 not 0x0A). It just adds a function
for incrementing/decrementing BCD integers by converting to decimal,
doing the increment/decrement and then converting back to BCD.
Signed-off-by: Nathaniel McCallum <nathaniel@natemccallum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The current code to generate usb modaliases from usb_device_id assumes
that the device's bcdDevice descriptor will actually be in BCD format.
While this should be a sane assumption, some devices don't follow spec
and just use plain old hex. This causes drivers for these devices to
generate invalid modalias lines which will never actually match for the
hardware.
The following patch adds hex support for bcdDevice in file2alias.c by
detecting when a driver uses a hex formatted bcdDevice_(lo|hi) and
adjusts the output to hex format accordingly.
Drivers for devices which have bcdDevice conforming to BCD will have no
change in modalias output. Drivers for devices which don't conform
(i.e. ibmcam) should now generate valid modaliases.
EXAMPLE OUTPUT (ibmcam; space added to highlight change)
Old: usb:v0545p800D d030[10-9] dc*dsc*dp*ic*isc*ip*
New: usb:v0545p800D d030a dc*dsc*dp*ic*isc*ip*
Signed-off-by: Nathaniel McCallum <nathaniel@natemccallum.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes it consistent with other buses (platform, i2c, vio, ...). I'm
not sure why we use the prefixes, but there must be a reason.
This was easy enough to do it, and I did it.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Dmitry Torokhov <dtor@mail.ru>
Cc: Samuel Ortiz <sameo@openedhand.com>
Cc: "John W. Linville" <linville@tuxdriver.com>
Acked-by: Mike Frysinger <vapier.adi@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
With this patch spi drivers can use standard spi_driver.id_table and
MODULE_DEVICE_TABLE() mechanisms to bind against the devices. Just like
we do with I2C drivers.
This is useful when a single driver supports several variants of devices
but it is not possible to detect them in run-time (like non-JEDEC chips
probing in drivers/mtd/devices/m25p80.c), and when platform_data usage is
overkill.
This patch also makes life a lot easier on OpenFirmware platforms, since
with OF we extensively use proper device IDs in modaliases.
Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com>
Cc: David Brownell <dbrownell@users.sourceforge.net>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Jean Delvare <khali@linux-fr.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
This patch allows a virtio driver to use VIRTIO_DEV_ANY_ID for the
device id. This will be used by a test module that can be bound to
any virtio device.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Now platform_device is being widely used on SoC processors where the
peripherals are attached to the system bus, which is simple enough.
However, silicon IPs for these SoCs are usually shared heavily across
a family of processors, even products from different companies. This
makes the original simple driver name based matching insufficient, or
simply not straight-forward.
Introduce a module id table for platform devices, and makes it clear
that a platform driver is able to support some shared IP and handle
slight differences across different platforms (by 'driver_data').
Module alias is handled automatically when a MODULE_DEVICE_TABLE()
is defined.
To not disturb the current platform drivers too much, the matched id
entry is recorded and can be retrieved by platform_get_device_id().
Signed-off-by: Eric Miao <eric.miao@marvell.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
Cc: Ben Dooks <ben-linux@fluff.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Fix endianness of bus member of hid_device_id in modpost.
Signed-off-by: Jiri Slaby <jirislaby@gmail.com>
Reported-by: Nye Liu <nyet@mrv.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Based on a patch from Brian, who identified the issue.
Signed-off-by: Bryan Kadzban <bryan@kadzban.is-a-geek.net>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This makes modpost handle MODULE_DEVICE_TABLE(dmi, xxxx).
I had to change the string pointers in the match table to char arrays,
and picked a size of 79 bytes almost at random -- do we need to make it
bigger than that? I was a bit concerned about the 'bloat' this
introduces into the match tables, but they should all be __initdata so
it shouldn't matter too much.
(Actually, modpost does go through the relocations and look at most of
them; it wouldn't be impossible to make it handle string pointers -- but
doesn't seem to be worth the effort, since they're __initdata).
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
With 22454cb99f we added only the
first entry of the device table. We need to loop over the whole
device list.
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Trying to compile the v850 port brings many compile errors, one of them exists
since at least kernel 2.6.19.
There also seems to be noone willing to bring this port back into a usable
state.
This patch therefore removes the v850 port.
If anyone ever decides to revive the v850 port the code will still be
available from older kernels, and it wouldn't be impossible for the port to
reenter the kernel if it would become actively maintained again.
Signed-off-by: Adrian Bunk <bunk@kernel.org>
Acked-by: Greg Ungerer <gerg@uclinux.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Along with the non-modalias conformant "pnp:*" aliases, we add "acpi:*"
entries to PNP drivers, to allow module autoloading by ACPI PNP device
entries, which export proper modalias information, without any specific
userspace modprobe mangling.
Cc: Adam Belay <ambx1@neo.rr.com>
Cc: Thomas Renninger <trenn@suse.de>
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add modalias and subchannel type attributes for all subchannels.
I/O subchannel specific attributes are now created in
io_subchannel_probe(). modalias and subchannel type are also
added to the uevent for the css bus. Also make the css modalias
known.
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Not all device types need a wildcard at the end of their module
aliases. In particular, for i2c module aliases, the trailing wildcard
is not only unneeded, it could also cause the wrong driver to be
loaded.
As I2C devices have no IDs, i2c module aliases are simple, arbitrary
device names. For example:
$ /sbin/modinfo lm90
filename: /lib/modules/2.6.25-git18/kernel/drivers/hwmon/lm90.ko
author: Jean Delvare <khali@linux-fr.org>
description: LM90/ADM1032 driver
license: GPL
vermagic: 2.6.25-git18 mod_unload
depends: hwmon
alias: i2c:lm90*
alias: i2c:adm1032*
alias: i2c:lm99*
alias: i2c:lm86*
alias: i2c:max6657*
alias: i2c:adt7461*
alias: i2c:max6680*
$
This would cause trouble if one I2C chip name matches the beginning of
another I2C chip name and both chips are supported by different
drivers. For example, an i2c device named lm9042 would cause the lm90
driver to be loaded, while it doesn't support that device. This case
has yet to be seen in practice, but still, I'd like to fix it now. The
cleanest fix is to remove the trailing wildcard from i2c module aliases.
Here's a patch doing this.
Not all device type aliases need a trailing wildcard, in particular
the i2c aliases don't. Don't add a wildcard by default in do_table(),
instead let each device type handler add it if needed.
I have tested types acpi, dmi, eisa, i2c, ide, ieee1394, input, pci,
pcmcia, platform, pnp, scsi, serio, ssb and usb. Other types (ccw, of,
vio, parisc, sdio and virtio) are untested.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jochen Friedrich <jochen@scram.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Based on earlier work by Jon Smirl and Jochen Friedrich.
This patch allows new-style i2c chip drivers to have alias names using
the official kernel aliasing system and MODULE_DEVICE_TABLE(). At this
point, the old i2c driver binding scheme (driver_name/type) is still
supported.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Jochen Friedrich <jochen@scram.de>
Cc: Jon Smirl <jonsmirl@gmail.com>
Cc: Kay Sievers <kay.sievers@vrfy.org>
The current PNP combined card + devices module aliase can
never ever match anything, because these values are not available
all at the same time to request a module.
Instead of adding the combined alias, we add the device id's
all as individual aliases. Device id's are exported by the PNP
bus and can now properly used to request the loading of a
matching module.
The module snd-sbawe currently exports aliases, which can never
match anything:
alias: pnp:cCTLXXXXdCTL0045dCTL0022*
alias: pnp:cCTLXXXXdCTL0044dCTL0023*
alias: pnp:cCTLXXXXdCTL0042dCTL0022*
alias: pnp:cCTLXXXXdCTL0041dCTL0021*
alias: pnp:cCTLXXXXdCTL0031dCTL0021*
alias: pnp:cCTL00eddCTL0041dCTL0070*
alias: pnp:cCTL00e9dCTL0045dCTL0022*
alias: pnp:cCTL00e4dCTL0045dCTL0022*
alias: pnp:cCTL00c7dCTL0045dCTL0022*
alias: pnp:cCTL00c5dCTL0045dCTL0022*
alias: pnp:cCTL00c3dCTL0045dCTL0022*
alias: pnp:cCTL00c1dCTL0042dCTL0022*
alias: pnp:cCTL00b2dCTL0044dCTL0023*
alias: pnp:cCTL009edCTL0044dCTL0023*
alias: pnp:cCTL009ddCTL0042dCTL0022*
alias: pnp:cCTL009fdCTL0041dCTL0021*
alias: pnp:cCTL009cdCTL0041dCTL0021*
alias: pnp:cCTL009adCTL0041dCTL0021*
alias: pnp:cCTL0054dCTL0031dCTL0021*
alias: pnp:cCTL0048dCTL0031dCTL0021*
alias: pnp:cCTL0047dCTL0031dCTL0021*
alias: pnp:cCTL0046dCTL0031dCTL0021*
alias: pnp:cCTL0045dCTL0031dCTL0021*
alias: pnp:cCTL0044dCTL0031dCTL0021*
alias: pnp:cCTL0043dCTL0031dCTL0021*
alias: pnp:cCTL0042dCTL0031dCTL0021*
alias: pnp:cCTL0039dCTL0031dCTL0021*
alias: pnp:cCTL0035dCTL0031dCTL0021*
With this patch it exports only the device id's, as properly
matchable aliases:
alias: pnp:dCTL0070*
alias: pnp:dCTL0045*
alias: pnp:dCTL0023*
alias: pnp:dCTL0044*
alias: pnp:dCTL0022*
alias: pnp:dCTL0042*
alias: pnp:dCTL0041*
alias: pnp:dCTL0021*
alias: pnp:dCTL0031*
Now, the exported value of the PNP bus can be used to autoload
a matching module:
$ modprobe --first-time -n -v pnp:dCTL0045
insmod /lib/modules/2.6.24-rc6-g5b825ed2-dirty/kernel/sound/core/snd-rawmidi.ko
insmod /lib/modules/2.6.24-rc6-g5b825ed2-dirty/kernel/sound/drivers/mpu401/snd-mpu401-uart.ko
insmod /lib/modules/2.6.24-rc6-g5b825ed2-dirty/kernel/sound/core/snd-hwdep.ko
insmod /lib/modules/2.6.24-rc6-g5b825ed2-dirty/kernel/sound/isa/sb/snd-sb-common.ko
insmod /lib/modules/2.6.24-rc6-g5b825ed2-dirty/kernel/sound/isa/sb/snd-sb16-csp.ko
insmod /lib/modules/2.6.24-rc6-g5b825ed2-dirty/kernel/sound/isa/sb/snd-sb16-dsp.ko
insmod /lib/modules/2.6.24-rc6-g5b825ed2-dirty/kernel/sound/drivers/opl3/snd-opl3-lib.ko
insmod /lib/modules/2.6.24-rc6-g5b825ed2-dirty/kernel/sound/isa/sb/snd-sbawe.ko
$ grep CTL0045 /sys/bus/pnp/devices/*/id
/sys/bus/pnp/devices/01:01.00/id:CTL0045
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
The module alias support in the kernel have a consistency
check where it is checked that the size of a structure
in the kernel and on the build host are the same.
For cross builds this check does not make sense so detect
when we do cross builds and silently skip the check in these
situations.
This fixes a build bug for a wireless driver when cross building
for arm.
Acked-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Gordon Farquharson <gordonfarquharson@gmail.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: stable@kernel.org
Some crazy devices in the wild have a vendor id of 0x0000. If we try to
add a module alias with this id, we just can't do it due to a check in
the file2alias.c file. Change the test to verify that both the vendor
and product ids are 0x0000 to show a real "blank" module alias.
Note, the module-init-tools package also needs to be changed to properly
generate the depmod tables.
Cc: Janusz <janumix@poczta.fm>
Cc: stable <stable@kernel.org>
Cc: Jon Masters <jcm@redhat.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
This adds the logic to convert the virtio ids into module aliases, and
includes a modalias entry in sysfs and the env var to make probing work.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
* git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild: (40 commits)
kbuild: introduce ccflags-y, asflags-y and ldflags-y
kbuild: enable 'make CPPFLAGS=...' to add additional options to CPP
kbuild: enable use of AFLAGS and CFLAGS on commandline
kbuild: enable 'make AFLAGS=...' to add additional options to AS
kbuild: fix AFLAGS use in h8300 and m68knommu
kbuild: check for wrong use of CFLAGS
kbuild: enable 'make CFLAGS=...' to add additional options to CC
kbuild: fix up CFLAGS usage
kbuild: make modpost detect unterminated device id lists
kbuild: call export_report from the Makefile
kbuild: move Kai Germaschewski to CREDITS
kconfig/menuconfig: distinguish between selected-by-another options and comments
kconfig: tristate choices with mixed tristate and boolean values
include/linux/Kbuild: remove duplicate entries
kbuild: kill backward compatibility checks
kbuild: kill EXTRA_ARFLAGS
kbuild: fix documentation in makefiles.txt
kbuild: call make once for all targets when O=.. is used
kbuild: pass -g to assembler under CONFIG_DEBUG_INFO
kbuild: update _shipped files for kconfig syntax cleanup
...
Fix up conflicts in arch/um/sys-{x86_64,i386}/Makefile manually.
I2C devices do not have any form of ID as PCI or USB devices have.
No driver uses "MODULE_DEVICE_TABLE(i2c, ...)" because it doesn't
make sense. So we can get rid of struct i2c_device_id and the
associated support code.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Greg KH <greg@kroah.com>
Linus Torvalds