Missed .owner of struct snd_soc_card will prevent the module from being
removed from underneath its users.
Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure that everything is seeing the same declaration by moving it to
a header file rather than putting the declaration in soc-core.c
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Missed .owner of struct snd_soc_card will prevent the module from being
removed from underneath its users.
Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Missed .owner of struct snd_soc_card will prevent the module from being
removed from underneath its users.
Reported-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DAI link endpoints and platform (DMA) devices are currently specified
by name. When instantiating sound cards from device tree, it may be more
convenient to refer to these devices by phandle in the device tree, and
for code to describe DAI links using the "struct device_node *"
("of_node") those phandles map to.
This change adds new fields to snd_soc_dai_link which can "name" devices
using of_node, enhances soc_bind_dai_link() to allow binding based on
of_node, and enhances snd_soc_register_card() to ensure that illegal
combinations of name and of_node are not used.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Sharing and not reinitialising static pcm_hardware struct resulted in
stream format validity flags being incorrectly shared between cards.
Fix and clarify by declaring locally and initialising in the open functions.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Since introduction of mono and low latency modes, fixed channel count of 2
is not always valid. Use reported max_channels instead.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Previously, only payload and size were correct, sufficient for reading,
but other fields produced spurious debug output.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It is useful to know the HPI version without having to load the module,
in order to determine the matching firmware version.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add new error codes, and adapter properties.
Clean up some comments.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
dsp_code struct is not created if firmware is invalid, so check
and zero of firmware pointer is not necessary
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Structs hpi_adapter and snd_card_asihpi had members that
duplicate those in underlying hpi_adapter_obj or whose info
can be retrieved using hpi_adapter_get_info().
Print less info in probe function, it can be retrieved from /proc.
Avoid name redundancy: hpi_adapter_obj.adapter_type renamed to .type
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Structs related to network flash update are not required in kernel.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The channel count can be queried to determine which.
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unlike other streams which support 1..max channels,
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Elapsed counter should only count data committed to snd_pcm_period_elapsed,
rather than all data available
Signed-off-by: Eliot Blennerhassett <eblennerhassett@audioscience.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: atmel/ac97c: using software reset instead hardware reset if not available
This driver is parameterized in two ways:
a) Platform data, which supplies the set of GPIOs used by the driver.
These GPIOs can now be parsed out of device tree.
b) Machine-specific DAPM route arrays embedded into the ASoC machine
driver itself. Historically, the driver picks the appropriate array
to use using machine_is_*(). The driver now requires this array to
be parsed from device tree when instantiated through device tree,
using the core ASoC support for this parsing.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implement snd_soc_of_parse_audio_routing(), a utility function that can
parses a simple DAPM route table from device tree.The machine driver
specifies the DT property to use, since this is binding-specific.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Implement snd_soc_of_parse_card_name(), a utility function that sets a
card's name from device tree. The machine driver specifies the DT
property to use, since this is binding-specific.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The module desciption says this is ASoC alc5621/2/3 driver.
Make the naming consistent with the reset of the code.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Reviewed-by: Mika Westerberg <mika.westerberg@iki.fi>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Alexander Sverdlin <subaparts@yandex.ru>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The commit 49920bc (dmaengine: add new enum dma_transfer_direction)
changes the type of parameter 'direction' of device_prep_dma_cyclic
from dma_data_direction to dma_transfer_direction.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Dong Aisheng <dong.aisheng@linaro.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't need to export s3c_pcm_dai after multi-component patch.
Thus remove export of s3c_pcm_dai and make it static.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
At this stage only Toshiba AC100/Dynabook supported.
Signed-off-by: Leon Romanovsky <leon@leon.nu>
Signed-off-by: Andrey Danin <danindrey@mail.ru>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
These drviers defined only variables but didn't declare as module
parameters. Also fix the enable variable to bool type.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
module_param(bool) used to counter-intuitively take an int. In
fddd5201 (mid-2009) we allowed bool or int/unsigned int using a messy
trick.
It's time to remove the int/unsigned int option. For this version
it'll simply give a warning, but it'll break next kernel version.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
We write the reset register with the default value so it should not be
mistakenly written.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_register_card() instead of creating a "soc-audio" platform device.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow McBSP FIFO configuration from ASoC dai driver
on OMAP4 platform.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: HDA: Use LPIB Position fix for Intel SCH Poulsbo
ALSA: hda: fix mute led polarity for HP laptops with buggy BIOS
ALSA: HDA: Set position fix to LPIB for an Atom/Poulsbo based device
ASoC: Fix hx4700 error handling to free gpios if snd_soc_register_card fails
ASoC: WM8958: correctly show firmware magic on mismatch
ASoC: mxs: Add appropriate MODULE_ALIAS()
ASoC: mxs: Add missing MODULE_LICENSE("GPL")
ASoC: Fix WM8996 24.576MHz clock operation
ASoC: Include linux/module.h for smdk2443_wm9710
ASoC: Fix a typo in jive_wm8750
ASoC: Fix build dependency for SND_SOC_JZ4740_CODEC
ASoC: Include linux/io.h for jz4740 codec
The variable ret_val is used but not declared. This causes
the following compile error:
sound/soc/mid-x86/sst_platform.c: In function ‘sst_platform_open’:
sound/soc/mid-x86/sst_platform.c:274:2: error: ‘ret_val’ undeclared (first use in this function)
sound/soc/mid-x86/sst_platform.c:274:2: note: each undeclared identifier is reported only once for each function it appears in
make[1]: *** [sound/soc/mid-x86/sst_platform.o] Error 1
Fix this.
Signed-off-by: Joerg Roedel <joerg.roedel@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Several people with this chipset have reported inconsistent/sloppy
values for position reporting when the DMA position buffer is used,
and that setting position_fix=1 have fixed their problems.
BugLink: https://bugs.launchpad.net/bugs/825709
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that the core holds a pm_runtime reference to the device while the
link is active there is no need for the driver to do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that the core holds a pm_runtime reference to the device while the
link is active there is no need for the driver to do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use longer intervals when the microphone is not inserted to increase
robustness against leisurely insertion.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch adds HDMI audio support for new AMD products. As HW default
disable snoop, force non-snoop mode in HD audio driver.
Signed-off-by: Andiry Xu <andiry.xu@amd.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Commit b99a776d0b removed all effects of
the STAC92HD83* model quirk "hp". However, it left the model selection
and documentation behind, confusing users with inverted mute
leds. Completely remove this quirk and its documentation.
Signed-off-by: Gustavo Maciel Dias Vieira <gustavo@sagui.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by Vinod Koul <vinod.koul@linux.intel.com>
Acked-by: Lu Guanqun <guanqun.lu@intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Both sh4_hac_dai and sh7760_soc_platform are changed to static
by multi-component patch and they are not used in sh7760-ac97.c now.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Otherwise there's a race where the DAI might get used without everything
having been set up.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Sangbeom Kim <sbkim73@samsung.com>
Use an getter function in plat-orion/addr-map.c to get the address map
structure, rather than pass it to drivers in the platform_data
structures. When the drivers are built for none orion platforms, a
dummy function is provided instead which returns NULL.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Michael Walle <michael@walle.cc>
Acked-by: Nicolas Pitre <nico@linaro.org>
Signed-off-by: Nicolas Pitre <nico@fluxnic.net>
Some HP laptop models do not have a properly filled OEM string used
to set the gpio and polarity of the mute led. Make the mute led
configuration work for this case.
Signed-off-by: Gustavo Maciel Dias Vieira <gustavo@sagui.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This may lead to problems (like loss of sound) as GPIO pin may be used
for different function (SPDIF OUT, EAPD etc) on those systems. This patch
disables default mute LED GPIO configuration on all new codecs as all new
HP systems are expected to provide explicit mute LED configuration in SMBIOS.
Signed-off-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Now that the mfd is using the register map cache there's no need for the
CODEC driver to do any register cache management or any funny dances to
interact with the other drivers using the device so just remove the cache
initialisation and volatility information.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Just go directly to the regmap API, saving code and making integration
that bit more direct.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a bunch of definitions for wm8994 registers that are not currently
used by software.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
With the auto-parser we can choose the dac nid for vmaster from
the DACs we already know, instead of hard-coding it. This is more
future-proof and was actually wrong on one machine.
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
This driver can be built as module and the file header indicates that
the driver is published under the GPL.
Thus add MODULE_LICENSE("GPL") for it.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
For the Asus 1101HA, reporting position by reading the DMA position
buffer map seems unstable and often wrong. The reporter says that
position_fix=LPIB works much better (although not 100%, but this is
probably due to other issues).
The controller chip is an Intel Poulsbo 8086:811b (rev 07) controller,
and complete alsa-info is available here:
https://launchpadlibrarian.net/86691768/alsa-info.txt.1TNwyE5Ea7
Cc: stable@kernel.org (3.0+)
BugLink: http://bugs.launchpad.net/bugs/825709
Tested-by: Stefano Lodi
Signed-off-by: David Henningsson <david.henningsson@canonical.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
To support advanced system functionality for additional components; the
actively used clocks will remain the same for current components. Also
factor the rate out to a single #define while we're at it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The message was obviously copied from soc_init_codec_debugfs()
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The sound driver refuses to load as module, because of the missing
MODULE_LICENSE("GPL").
The file header indicates that the driver is indeed published under
the GPL.
Signed-off-by: Lothar Waßmann <LW@KARO-electronics.de>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Record the clock after the divider as that is what all SYSCLK users see.
Without this the other clock configuration in the device comes out at
half rate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda/realtek - Fix lost speaker volume controls
ALSA: hda/realtek - Create "Bass Speaker" for two speaker pins
ALSA: hda/realtek - Don't create extra controls with channel suffix
ALSA: hda - Fix remaining VREF mute-LED NID check in post-3.1 changes
ALSA: hda - Fix GPIO LED setup for IDT 92HD75 codecs
ASoC: Provide a more complete DMA driver stub
ASoC: Remove references to corgi and spitz from machine driver document
ASoC: Make SND_SOC_MX27VIS_AIC32X4 depend on I2C
ASoC: Fix dependency for SND_SOC_RAUMFELD and SND_PXA2XX_SOC_HX4700
ASoC: uda1380: Return proper error in uda1380_modinit failure path
ASoC: kirkwood: Make SND_KIRKWOOD_SOC_OPENRD and SND_KIRKWOOD_SOC_T5325 depend on I2C
ASoC: Mark WM8994 ADC muxes as virtual
ALSA: hda/realtek - Fix Oops in alc_mux_select()
ALSA: sis7019 - give slow codecs more time to reset
Transform some loops from:
for_each(x) {
if (f(x)) {
work_on(x);
}
}
to new structure:
for_each(x) {
if (!f(x))
continue;
work_on(x);
}
This will allow future modification of f(x) with less impact to the code.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move DAS routing setup into the DAS driver itself. This removes the need
to duplicate this in each machine driver, of which we'll soon have three.
An added advantage is that the machine drivers no longer call the Tegra20-
specific DAS functions by name, so the machine driver no longer needs to
be split up into Tegra20 and Tegra30 versions.
If individual machine drivers need a different routing setup to this
default, they can still call the DAS functions to set that up.
Long-term, DAS will be a codec driver, and user-space will be able to
control its routing, possibly within constraints that the machine driver
sets up. Configuring the DAS routing from the DAS driver is a very slight
move in that direction.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use snd_soc_update_bits for read-modify-write register access instead of
open-coding it using snd_soc_read and snd_soc_write
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
As for PCMs take a runtime power management reference to devices that are
in a non-off bias, avoiding the need to do this in individual drivers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Now that the core holds a pm_runtime reference to the device while the
link is active there is no need for the driver to do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Now that the core holds a pm_runtime reference to the device while the
link is active there is no need for the driver to do so.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Every device that implements runtime power management for DAIs is doing
it in pretty much the same way: in the startup callback they take a
runtime PM reference and then in the shutdown callback they release that
reference, keeping the device active while the DAI is active. Given the
frequency with which this is done and the obviousness of the need to keep
the device active in this period factor the code out into the core, taking
references on the device for each CPU DAI, CODEC DAI and DMA device in the
core.
As runtime PM is reference counted this shouldn't interfere with any
other reference holding by the drivers, and since (in common with the
existing implementations) we don't check for errors on enabling it
shouldn't matter if the device actually has runtime PM enabled or not.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Add basic support for the Au1300 variant(s):
- New GPIO/Interrupt controller
- DBDMA ids
- USB setup
- MMC support
- enable various PSC drivers
- detection code.
Signed-off-by: Manuel Lauss <manuel.lauss@googlemail.com>
To: linux-mips@linux-mips.org
Patchwork: https://patchwork.linux-mips.org/patch/2866/
Signed-off-by: Ralf Baechle <ralf@linux-mips.org>
When there are the same or more number of HP pins are available, HP pins
are used as the primary outputs instead of the speaker pins. But, in
some cases (especially with ALC663 & co), some DACs are available only
with a later pin and it's assigned to a speaker, and since the driver
parses the pins from the lower NID, such a DAC was skipped eventually
without assignments. This resulted in a regression, the missing speaker
volume control in the new parser.
As a workaround for this, now the driver retries the pin->DAC mapping
again after restoring the speaker-pins as primary. This is still an ad
hoc fix, but it works so far for most of Realtek codecs.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
On systems with two speaker pins, the secondary speaker pin is mostly
assigned to a bass speaker instead of a surround. Thus it makes more
sense to rename the control properly.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The multiple headphone or speaker pins are usually provided to
output the same stream unlike line-out jacks (which are supposed
to be multi-channel surrounds). Thus giving a mixer name like
"Headphone Surround" is rather confusing. Instead, when multiple
headphone volumes are available, use index with the same "Headphone"
name.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Fix a typo introduced by commit e00c3f55
"ASoC: Convert Samsung directory to module_platform_driver".
This fixes the build error:
CC sound/soc/samsung/s3c24xx_simtec_tlv320aic23.o
sound/soc/samsung/s3c24xx_simtec_tlv320aic23.c: In function 'simtec_audio_tlv320aic32_driver_init':
sound/soc/samsung/s3c24xx_simtec_tlv320aic23.c:105: error: 'simtec_audio_tlv320aic32_driver' undeclared (first use in this function)
sound/soc/samsung/s3c24xx_simtec_tlv320aic23.c:105: error: (Each undeclared identifier is reported only once
sound/soc/samsung/s3c24xx_simtec_tlv320aic23.c:105: error: for each function it appears in.)
sound/soc/samsung/s3c24xx_simtec_tlv320aic23.c: In function 'simtec_audio_tlv320aic32_driver_exit':
sound/soc/samsung/s3c24xx_simtec_tlv320aic23.c:105: error: 'simtec_audio_tlv320aic32_driver' undeclared (first use in this function)
make[3]: *** [sound/soc/samsung/s3c24xx_simtec_tlv320aic23.o] Error 1
make[2]: *** [sound/soc/samsung] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
I think we had better naming it with *driver, thus I change
it to simtec_audio_tlv320aic23_driver.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Include linux/module.h to fix below build error:
CC sound/soc/samsung/smdk2443_wm9710.o
sound/soc/samsung/smdk2443_wm9710.c:64: error: expected declaration specifiers or '...' before string constant
sound/soc/samsung/smdk2443_wm9710.c:64: warning: data definition has no type or storage class
sound/soc/samsung/smdk2443_wm9710.c:64: warning: type defaults to 'int' in declaration of 'MODULE_AUTHOR'
sound/soc/samsung/smdk2443_wm9710.c:64: warning: function declaration isn't a prototype
sound/soc/samsung/smdk2443_wm9710.c:65: error: expected declaration specifiers or '...' before string constant
sound/soc/samsung/smdk2443_wm9710.c:65: warning: data definition has no type or storage class
sound/soc/samsung/smdk2443_wm9710.c:65: warning: type defaults to 'int' in declaration of 'MODULE_DESCRIPTION'
sound/soc/samsung/smdk2443_wm9710.c:65: warning: function declaration isn't a prototype
sound/soc/samsung/smdk2443_wm9710.c:66: error: expected declaration specifiers or '...' before string constant
sound/soc/samsung/smdk2443_wm9710.c:66: warning: data definition has no type or storage class
sound/soc/samsung/smdk2443_wm9710.c:66: warning: type defaults to 'int' in declaration of 'MODULE_LICENSE'
sound/soc/samsung/smdk2443_wm9710.c:66: warning: function declaration isn't a prototype
make[3]: *** [sound/soc/samsung/smdk2443_wm9710.o] Error 1
make[2]: *** [sound/soc/samsung] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix a typo in jive_wm8750 that introduces below build error.
Also removes an unused err variable.
CC sound/soc/samsung/jive_wm8750.o
sound/soc/samsung/jive_wm8750.c: In function 'jive_wm8750_init':
sound/soc/samsung/jive_wm8750.c:104: warning: unused variable 'err'
sound/soc/samsung/jive_wm8750.c: At top level:
sound/soc/samsung/jive_wm8750.c:134: error: unknown field 'dapm_widgtets' specified in initializer
sound/soc/samsung/jive_wm8750.c:134: warning: initialization from incompatible pointer type
make[3]: *** [sound/soc/samsung/jive_wm8750.o] Error 1
make[2]: *** [sound/soc/samsung] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This allows the device to be matched against the device tree using the
compatible flag directly, as is standard, rather than falling back to
matching .id_table against the non-vendor portion of the first compatible
property value.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The advantage of kcalloc is, that will prevent integer overflows which could
result from the multiplication of number of elements and size and it is also
a bit nicer to read.
The semantic patch that makes this change is available
in https://lkml.org/lkml/2011/11/25/107
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Some HP laptops with IDT 92HD75 codecs may use a GPIO > 4 for the mute
LED, but currently the driver doesn't check this properly, and confuses
the mute LED behavior. This ended up with the silent output on some
HP laptops due to having another GPIO used as external amp control.
This patch fixes the problem by checking the max GPIO count and
comparing with the given value from DMI entry instead of magic fixed
value 4 and 8, and adding a new field to indicate the VREF mute-LED
behavior.
Reported-and-tested-by: Vitaliy Kulikov <Vitaliy.Kulikov@idt.com>
Cc: <stable@kernel.org> [v3.1]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Currently SND_SOC_JZ4740_CODEC depends on SOC_JZ4740 but SOC_JZ4740 is not
defined in any Kconfig. Thus the codec driver will not be built when select
"Build all ASoC CODEC drivers".
(Unless it is selected by SND_JZ4740_SOC_QI_LB60).
Remove the dependency with SOC_JZ4740, then this code driver can be built when
select "Build all ASoC CODEC drivers".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Include linux/io.h to fix below build errors:
CC sound/soc/codecs/jz4740.o
sound/soc/codecs/jz4740.c: In function 'jz4740_codec_read':
sound/soc/codecs/jz4740.c:82: error: implicit declaration of function 'readl'
sound/soc/codecs/jz4740.c: In function 'jz4740_codec_write':
sound/soc/codecs/jz4740.c:92: error: implicit declaration of function 'writel'
sound/soc/codecs/jz4740.c: In function 'jz4740_codec_probe':
sound/soc/codecs/jz4740.c:373: error: implicit declaration of function 'ioremap'
sound/soc/codecs/jz4740.c:373: warning: assignment makes pointer from integer without a cast
sound/soc/codecs/jz4740.c:393: error: implicit declaration of function 'iounmap'
make[3]: *** [sound/soc/codecs/jz4740.o] Error 1
make[2]: *** [sound/soc/codecs] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If we fail to read the IRQ type from the interrupt controller don't
fail, just assume a value and solider on - we may fail later when we try
to request the IRQ but it's possible we'll succeed.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Document the device tree binding for the WM8903 codec, and modify the
driver to extract platform data from the device tree, if present.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
If the WM8903 is hooked up to an interrupt, set the irq_active_low flag
in the default platform data based on the IRQ's IRQ_TYPE. Map IRQ_TYPE_NONE
(a lack of explicit configuration/restriction) to irq_active_low = false;
the previous default.
This code is mainly added to support device tree interrupt bindings,
although will work perfectly well in a non device tree system too.
Any interrupt controller that supports only a single IRQ_TYPE could
set each IRQ's type based on that restriction. This applies equally
with and without device tree. To cater for interrupt controllers
that don't do this, for which irqd_get_trigger_type() will return
IRQ_TYPE_NONE, the platform data irq_active_low field may be used
in systems that don't use device tree.
With device tree, every IRQ must have some IRQ_TYPE set.
Controllers that support DT and multiple IRQ_TYPEs must define the
interrupts property (as used in interrupt source nodes) such that it
defines the IRQ_TYPE to use. When the core DT setup code initializes
wm8903->irq, the interrupts property will be parsed, and as a side-
effect, set the IRQ's IRQ_TYPE for the WM8903 probe() function to read.
Controllers that support DT and a single IRQ_TYPE could arrange to
set the IRQ_TYPE somehow during their initialization, or hard-code
it during the processing of the child interrupts property.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The pdata pointer is now always valid. Remove any conditions that check
its validity.
This patch is mostly just removing an indentation level. One variable had
to be moved due to the removal of a scope, and one comment was split into
two. Viewing the patch with git show/diff -b will show that it's actually
very small.
Note that WM8903_MIC_BIAS_CONTROL_0 is now written unconditionally,
whereas it used to be written only if pdata was supplied. Since
defpdata.micdet_cfg = 0, this unconditional write simply echos the HW
defaults in the case where pdata is not supplied.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
wm8903_platform_data.gpio_cfg[] was intended to be interpreted as follows:
0: Don't touch this GPIO's configuration register
1..7fff: Write that value to the GPIO's configuration register
8000: Write zero to the GPIO's configuration register
other: Undefined (invalid)
The rationale is that platform data is usually global data, and a value of
zero means that the field wasn't explicitly set to anything (e.g. because
the field was new to the pdata type, and existing users weren't update to
initialize it) and hence the value zero should be ignored. 0x8000 is an
explicit way to get 0 in the register.
The code worked this way until commit 7cfe561 "ASoC: wm8903: Expose GPIOs
through gpiolib", where the behaviour was changed due to my lack of
awareness of the above rationale.
This patch reverts to the intended behaviour, and updates all in-tree users
to use the correct scheme. This also makes WM8903 consistent with other
devices that use a similar scheme.
WM8903_GPIO_NO_CONFIG is also renamed to WM8903_GPIO_CONFIG_ZERO so that
its name accurately reflects its purpose.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Cc: Olof Johansson <olof@lixom.net>
Cc: Colin Cross <ccross@android.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow userspace applications to do more parameter setting by providing a
more complete stub DMA driver specifying a wildcard set of formats and
channels and essentially random values for the DMA parameters. This is
required for useful runtime operation of the dummy DMA driver until we
are able to figure out how to power up links and do hw_params() from DAPM.
Sending to stable as without this the dummy driver is not terribly
useful.
Reported-by: Kyung-Kwee Ryu <Kyung-Kwee.Ryu@wolfsonmicro.com>
Tested-by: Kyung-Kwee Ryu <Kyung-Kwee.Ryu@wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org
lower level drivers typically register with upper layers.
So fix by exporting symbols from sst_platform driver for dsp driver to
register to sst platform driver
Now this driver doesnt depend on sst driver, so remove the dependency
and the header files
Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
reg_cache_size is supposed to be the number of elements in the register cache,
not the size in bytes.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Using gpio_request_one can make the error handling simpler.
Also remove a redundant "Failed to issue reset" error message.
We already show the error message in uda1380_reset() error path.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SND_SOC_MX27VIS_AIC32X4 selects SND_SOC_TLV320AIC32X4,
but SND_SOC_TLV320AIC32X4 needs CONFIG_I2C.
So we need to make SND_SOC_MX27VIS_AIC32X4 depend on I2C.
otherwise I got below build error if CONFIG_I2C is not selected.
CC sound/soc/codecs/tlv320aic32x4.o
sound/soc/codecs/tlv320aic32x4.c: In function 'aic32x4_read':
sound/soc/codecs/tlv320aic32x4.c:323: error: implicit declaration of function 'i2c_smbus_read_byte_data'
sound/soc/codecs/tlv320aic32x4.c: In function 'aic32x4_probe':
sound/soc/codecs/tlv320aic32x4.c:641: error: 'i2c_master_send' undeclared (first use in this function)
sound/soc/codecs/tlv320aic32x4.c:641: error: (Each undeclared identifier is reported only once
sound/soc/codecs/tlv320aic32x4.c:641: error: for each function it appears in.)
sound/soc/codecs/tlv320aic32x4.c: In function 'aic32x4_modinit':
sound/soc/codecs/tlv320aic32x4.c:763: error: implicit declaration of function 'i2c_add_driver'
sound/soc/codecs/tlv320aic32x4.c: In function 'aic32x4_exit':
sound/soc/codecs/tlv320aic32x4.c:774: error: implicit declaration of function 'i2c_del_driver'
make[3]: *** [sound/soc/codecs/tlv320aic32x4.o] Error 1
make[2]: *** [sound/soc/codecs] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SND_SOC_RAUMFELD selects SND_SOC_CS4270 which needs CONFIG_I2C,
and also selects SND_SOC_AK4104 which needs SPI_MASTER.
Thus make SND_SOC_RAUMFELD depend on I2C && SPI_MASTER.
Add depend on SPI_MASTER to fix below build error if CONFIG_SPI_MASTER
is not selected.
LD .tmp_vmlinux1
sound/built-in.o: In function `ak4104_spi_write':
last.c:(.text+0x290cc): undefined reference to `spi_sync'
sound/built-in.o: In function `ak4104_probe':
last.c:(.text+0x292a0): undefined reference to `spi_write_then_read'
sound/built-in.o: In function `ak4104_spi_probe':
last.c:(.text+0x29398): undefined reference to `spi_setup'
sound/built-in.o: In function `ak4104_init':
last.c:(.init.text+0x4ec): undefined reference to `spi_register_driver'
make: *** [.tmp_vmlinux1] Error 1
Add depend on I2C to fix below build error if CONFIG_I2C is not selected:
CC sound/soc/codecs/cs4270.o
sound/soc/codecs/cs4270.c: In function 'cs4270_i2c_probe':
sound/soc/codecs/cs4270.c:657: error: implicit declaration of function 'i2c_smbus_read_byte_data'
sound/soc/codecs/cs4270.c: In function 'cs4270_init':
sound/soc/codecs/cs4270.c:730: error: implicit declaration of function 'i2c_add_driver'
sound/soc/codecs/cs4270.c: In function 'cs4270_exit':
sound/soc/codecs/cs4270.c:736: error: implicit declaration of function 'i2c_del_driver'
make[3]: *** [sound/soc/codecs/cs4270.o] Error 1
make[2]: *** [sound/soc/codecs] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
SND_PXA2XX_SOC_HX4700 selects SND_SOC_AK4641 which needs CONFIG_I2C.
Thus make SND_PXA2XX_SOC_HX4700 depend on I2C.
Add depend on I2C to fix below build error if CONFIG_I2C is not selected:
CC sound/soc/codecs/ak4641.o
sound/soc/codecs/ak4641.c: In function 'ak4641_modinit':
sound/soc/codecs/ak4641.c:646: error: implicit declaration of function 'i2c_add_driver'
sound/soc/codecs/ak4641.c: In function 'ak4641_exit':
sound/soc/codecs/ak4641.c:656: error: implicit declaration of function 'i2c_del_driver'
make[3]: *** [sound/soc/codecs/ak4641.o] Error 1
make[2]: *** [sound/soc/codecs] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Return proper error for uda1380_modinit if i2c_add_driver() fails.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
SND_SOC_LITTLEMILL selects SND_SOC_WM8994, but SND_SOC_WM8994 needs MFD_WM8994.
Thus we need to select MFD_WM8994 to fix below build error:
LD .tmp_vmlinux1
sound/built-in.o: In function `wm8994_write':
sound/soc/codecs/wm8994.c:201: undefined reference to `wm8994_reg_write'
sound/built-in.o: In function `wm8994_read':
sound/soc/codecs/wm8994.c:222: undefined reference to `wm8994_reg_read'
sound/built-in.o: In function `wm8994_resume':
sound/soc/codecs/wm8994.c:2847: undefined reference to `wm8994_reg_read'
sound/built-in.o: In function `wm8994_codec_probe':
sound/soc/codecs/wm8994.c:3501: undefined reference to `wm8994_reg_read'
sound/soc/codecs/wm8994.c:3660: undefined reference to `wm8994_reg_read'
sound/soc/codecs/wm8994.c:3672: undefined reference to `wm8994_reg_read'
sound/built-in.o: In function `wm8958_dsp2_fw':
sound/soc/codecs/wm8958-dsp2.c:154: undefined reference to `wm8994_bulk_write'
make: *** [.tmp_vmlinux1] Error 1
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When no platform data is supplied, point pdata at a default platform
structure. This enables two future changes:
a) Defines the default platform data values in a single place.
b) There is always a valid pdata pointer, so some conditional code can
be simplified by a later patch.
Based on work by John Bonesio, but significantly reworked since then.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Get control of the device earlier and avoid trying to do an ASoC probe
on a card that won't work.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
Converting to an rbtree cache as regcache doesn't have a flat cache.
Since the top of the register map is fairly sparse this should be an
overall win.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
We only do this on initial power on so it's at best a waste of time as
the core will have already defaulted to the same values.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
The driver used to use a complicated method to sync the register cache
after having brought the bias level up to standby in resume due to the
use of the write sequencer to manage the initial power up. Now that we
don't use the write sequencer there is no need for this and we can just
use snd_soc_cache_sync() directly.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Tested-by: Stephen Warren <swarren@nvidia.com>
SND_KIRKWOOD_SOC_T5325 selects SND_SOC_ALC5623, but SND_SOC_ALC5623 needs
CONFIG_I2C. So we need to make SND_KIRKWOOD_SOC_T5325 depend on I2C,
otherwise I got below build error if CONFIG_I2C is not selected.
CC sound/soc/codecs/alc5623.o
sound/soc/codecs/alc5623.c: In function 'alc5623_i2c_probe':
sound/soc/codecs/alc5623.c:1002: error: implicit declaration of function 'i2c_smbus_read_word_data'
sound/soc/codecs/alc5623.c:1009: error: implicit declaration of function 'i2c_smbus_read_byte_data'
sound/soc/codecs/alc5623.c: In function 'alc5623_modinit':
sound/soc/codecs/alc5623.c:1096: error: implicit declaration of function 'i2c_add_driver'
sound/soc/codecs/alc5623.c: In function 'alc5623_modexit':
sound/soc/codecs/alc5623.c:1108: error: implicit declaration of function 'i2c_del_driver'
make[3]: *** [sound/soc/codecs/alc5623.o] Error 1
make[2]: *** [sound/soc/codecs] Error 2
make[1]: *** [sound/soc] Error 2
make: *** [sound] Error 2
Also fix the same issue for SND_KIRKWOOD_SOC_OPENRD.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Since they don't actually have power bits but do have events associated
with them it's important that we bootstrap their state properly which
making them virtual does.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Littlemill has one analogue microphone on the board (connected to IN1LN)
and an array of four DMICs connected to both DMICDAT lines. The biases
can be selected by jumpers but pick the default jumper fit.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The board supports CODECs that won't work with this but the CODEC driver
will check to see if it's running on the right chip for us.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
ALSA: hda - Fix S3/S4 problem on machines with VREF-pin mute-LED
ALSA: hda_intel - revert a quirk that affect VIA chipsets
ALSA: hda - Avoid touching mute-VREF pin for IDT codecs
firmware: Sigma: Fix endianess issues
firmware: Sigma: Skip header during CRC generation
firmware: Sigma: Prevent out of bounds memory access
ALSA: usb-audio - Support for Roland GAIA SH-01 Synthesizer
ASoC: Supply dcs_codes for newer WM1811 revisions
ASoC: Error out if we can't generate a LRCLK at all for WM8994
ASoC: Correct name of Speyside Main Speaker widget
ASoC: skip resume of soc-audio devices without codecs
ASoC: cs42l51: Fix off-by-one for reg_cache_size
ASoC: drop support for PlayPaq with WM8510
ASoC: mpc8610: tell the CS4270 codec that it's the master
ASoC: cs4720: use snd_soc_cache_sync()
ASoC: SAMSUNG: Fix build error
ASoC: max9877: Update register if either val or val2 is changed
ASoC: Fix wrong define for AD1836_ADC_WORD_OFFSET
When no imux is available (e.g. a single capture source),
alc_auto_init_input_src() may trigger an Oops due to the access to -1.
Add a proper zero-check to avoid it.
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Instead of using the 'cell-index' property in the I2C adapter node to
determine the adapter number, just query the i2c_adapter object directly.
Previously, the I2C nodes always appeared in cell-index order, so the
dynamic numbering coincided with the cell-index property. With commit
ab827d97 ("powerpc/85xx: Rework P1022DS device tree"), the I2C nodes are
unintentionally reversed in the device tree, and so the machine driver
guesses the wrong I2C adapter number.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Commit ab827d97 ("powerpc/85xx: Rework P1022DS device tree") renamed the
the /model property of the P1022DS device tree from "fsl,P1022" to
"fsl,P1022DS". To support both old and new device trees, the ASoC
machine driver for the P1022DS needs to query the /model property and
update the platform driver object dynamically.
Signed-off-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The GPIO registers are 15 bits wide. Hence values, higher than 0x7fff are
not legal GPIO register values. Modify the pdata.gpio_cfg handling code
to reject all illegal values, not just WM8903_GPIO_NO_CONFIG (0x8000). This
will allow the later use of 0xffffffff as an invalid value in future device
tree bindings, meaning "don't touch this GPIO's configuration".
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The existence of this parameter is purely historical. None of the CODEC drivers
uses it and we always pass in the same value anyway, so it should be safe to
remove it.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
A signal generator behaves as an input would but is not considered for
any of the special behaviour associated with external input pins. This
is especially useful when automatically working out not connected widgets.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Liam Girdwood <lrg@ti.com>
There are some AC97 codec and board combinations that have been observed
to take a very long time to respond after the cold reset has completed.
In one case, more than 350 ms was required. To allow users to have sound
on those platforms, we'll wait up to 500ms for the codec to become
ready.
As a board may have multiple codecs, with some faster than others to
reset, we add a module parameter to inform the driver which codecs
should be present.
Reported-by: KotCzarny <tjosko@yahoo.com>
Signed-off-by: David Dillow <dave@thedillows.org>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add master_mode and master_id in platfrom_data since it's board
specific and board knows it.
Then we can remove the function pointer in platfrom_data to make
the driver more devicetree friendly.
Signed-off-by: Dong Aisheng <b29396@freescale.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
* 'fixes' of http://ftp.arm.linux.org.uk/pub/linux/arm/kernel/git-cur/linux-2.6-arm:
ARM: 7182/1: ARM cpu topology: fix warning
ARM: 7181/1: Restrict kprobes probing SWP instructions to ARMv5 and below
ARM: 7180/1: Change kprobes testcase with unpredictable STRD instruction
ARM: 7177/1: GIC: avoid skipping non-existent PPIs in irq_start calculation
ARM: 7176/1: cpu_pm: register GIC PM notifier only once
ARM: 7175/1: add subname parameter to mfp_set_groupg callers
ARM: 7174/1: Fix build error in kprobes test code on Thumb2 kernels
ARM: 7172/1: dma: Drop GFP_COMP for DMA memory allocations
ARM: 7171/1: unwind: add unwind directives to bitops assembly macros
ARM: 7170/2: fix compilation breakage in entry-armv.S
ARM: 7168/1: use cache type functions for arch_get_unmapped_area
ARM: perf: check that we have a platform device when reserving PMU
ARM: 7166/1: Use PMD_SHIFT instead of PGDIR_SHIFT in dma-consistent.c
ARM: 7165/2: PL330: Fix typo in _prepare_ccr()
ARM: 7163/2: PL330: Only register usable channels
ARM: 7162/1: errata: tidy up Kconfig options for PL310 errata workarounds
ARM: 7161/1: errata: no automatic store buffer drain
ARM: perf: initialise used_mask for fake PMU during validation
ARM: PMU: remove pmu_init declaration
ARM: PMU: re-export release_pmu symbol to modules
Instead of managing input-jack stuff separately, call all stuff inside
the kctl-jack creation, deletion and report. The caller no longer needs
to care about input-jack.
The better integration between input-jack and kctl-jack should be done
in the upper layer in near future, but for now, it's implemented locally
for more tests.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Still have a manual free in there for some realloc()ed memory as there's
no devm version of that.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Allow systems to override the default microphone detection rates using
platform data in case the settings are not suitable (eg, due to an
unusually noisy jack).
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We don't need to rerun DAPM if the clock source is the same but we do
need to adjust the microphone detection rate in case we are moving from
an audio to a non-audio rate.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM1811A features an advanced low power accessory detection subsystem
which allows the device to be maintained in a very low power state while
the system is idle without sacrificing any accessory detection features.
Implement software support for this, automatically managing the power
configuration of the device depending on the detected accessory.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The WM8958 and WM1811 support detecting a range of buttons. Allow the
user to provide platform data enabling more of these levels without
having to write a custom detection handler.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The verb command in stac92xx_post_suspend caused the audio to stop
working after resuming from S3 mode on HP laptops with the VREF-pin
mute-LED control. Removing relevant post_suspend registering.
Although removing D3 on AFG is no optimal solution, the impact should
be small in comparison with the broken S3/S4.
Signed-off-by: Charles Chin <Charles.Chin@idt.com>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
All the other machine drivers for non-default configurations are named
after the relevant audio module so do so for Tobermory also.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Actively manage the detection rate for microphones with WM8958, providing
improved power consumption and maximising the benefit from the hardware
debounce.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
When we don't have any active audio we can put the microphone biases into
bypass mode to save power at the expense of performance.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We always store the register address as __iomem but pass it around as a
plain void * which upsets sparse.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Ensure SYSCLK is enabled while running accessory detection on WM8958.
It is always required so there is no sense in requiring machine drivers
to individually do this.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This quirk sould be reverted. It has the following probems:
1) The quirk was intended to "ASUS MV2-MX SE" motherboards only, but the
ID used matches a much broader range, potentially all boards containing a
VIA chipset model in the family of vendor VIA 0x1106 and audio device ID
0x3288, which encompasses VIA-VT82xx, VIA-VT1xx and VIA-VT20xx chipsets.
2) VIA chipsets rely on azx_via_get_position() to handle correctly dma
transfers during capture. Using POS_FIX_LPIB instead of POS_FIX_VIACOMBO
leads to partially corrupted input buffers during capture. The effects
of this bug are not immediately visible, it took strong DSP expertise,
some expensive signal generator and a spectrum analyzer to identify it
and verify correct behaviour using original default.
3) It's almost certain that the quirk did not fix the real problem,
if there was one. Refer to original submission:
http://mailman.alsa-project.org/pipermail/alsa-devel/2010-February/025109.html
Signed-of-by: Marc Vertes <mvertes@sigfox.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Add support for loading the SigmaDSP firmware using regmap. This allows us
to transparently use SPI or I2C as the transport protocol on devices which
support them.
For now we keep the old I2C support since we have one user of this which is not
straight forward to convert to regmap, due to variable length registers.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Move the structs and functions only used by SigmaDSP firmware loader itself
from the header to the C file.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Provide some error messages when loading the firmware fails, so it is possible
to diagnose the reason for the failure.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
It has been pointed out previously, that the firmware subsystem is not the right
place for the SigmaDSP firmware loader. Furthermore the SigmaDSP is currently
only used in audio products and we are aiming for better integration into the
ASoC framework in the future, with support for ALSA controls for firmware
parameters and support dynamic power management as well. So the natural choice
for the SigmaDSP firmware loader is the ASoC subsystem.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
What we want is to clear BIT[5:4](PCM_MODE_MASK) and BIT[3](PCM_BIT_ORDER) bits,
but current code clears BIT[2:0].
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Use the module_platform_driver() macro which makes
the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Added table quirks entry for Roland GAIA SH-01 Synthesizer based upon
Roland SH-201 table entry as template. USB MIDI and audio was tested
with Muse and Audacity.
Signed-off-by: John F Leach <jfleach@jfleach.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Use the module_platform_driver() macro which makes
the code smaller and a bit simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The Littlemill audio card supports a number of pluggable miniboards,
normally for the WM8994 family of devices. As all these devices look
mostly the same from an external configuration point of view and are
runtime enumerable we can write a standard machine driver which will
work out of the box with any of them. Start doing that with the bare
bones of a driver, only supporting AIF1.
Future patches will flesh this out to be more fully featured.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We can reduce the code size here a bit by using snd_soc_update_bits instead of
open-coding the read-modify-write cycle. The conversion done in this patch is
not completely straightforward and some minor code restructuring has been
incorporated to further reduce the code size.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add a DAPM supply widget for the internal sysclk, so it can be disabled
automatically when not needed.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
DAPM route controls only take effect on paths where the sink is a mixer or a
mux, furthermore the control must be a control assigned to the mixer or mux.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Factor out some boilerplate code.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
OMAP4 SDP/Blaze boards have digital microphones.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add support for OMAP4 Digital Microphone interface.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Also rename it to MICBIAS to reflect the pin name and help any out of tree
users notice the change.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
This makes the output a bit less confusing on multi-CODEC systems as the
same pin may appear in multiple CODECs.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
We need to enumerate all the CODECs that are part of the card we're
instantiating, not all the CODECs that are in the system as the system
may have multiple cards.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
This patch converts the drivers in sound/* to use the
module_platform_driver() macro which makes the code smaller and a bit
simpler.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
VT1708 has no support for unsolicited events per jack-plug, the driver
implements the workq for polling the jack-detection. The mixer element
"Jack Detect" was supposed to control this behavior on/off, but this
doesn't work properly as is now. The workq is always started and the
HP automute is always enabled.
This patch fixes the jack-detect control behavior by triggering / stopping
the work appropriately at the state change. Also the work checks the
internal state to continue scheduling or not.
Cc: <stable@kernel.org> [v3.1]
Signed-off-by: Takashi Iwai <tiwai@suse.de>
The CS420X_IMAC27 was copied from the line before but CS420X_APPLE
was clearly intented.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
It's never been updated so it can't be that useful and it makes the
driver needlessly chatty.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
commit 798681bf "ARM: 7158/1: add new MFP implement for NUC900"
adds subname parameter for mfp_set_groupg.
Thus add subname parameter to the callers.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Acked-by: Wan Zongshun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The new hardware tends to have more and more. As a temporary fix, just
increase the number for now.
For a long-term solution, we should assign the cvts/pins dynamically.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
So far, the driver supports up to 10 streams. This is a restriction in
hda_intel.c and hda_codec.c: in the former, the fixed array size limits
the amount, and in the latter, the fixed device-number assignment table
(in get_empty_pcm_device()) limits the possibility.
This patch reduces the restriction by
- using linked list for managing PCM instances in hda_intel.c, and
- assigning non-fixed device numbers for the extra devices
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Factor out some boilerplate code.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Jarkko Nikula <jarkko.nikula@bitmer.com>
Acked-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Factor out some boilerplate code.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Factor out some boilerplate code.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Axel Lin