Rather than having a separate constant for specifying the timeout on FLUSH
operations, use the basic I/O timeout value that is already configurable
on a per target basis to derive the FLUSH timeout. Looking at the current
definitions of these timeout values, the FLUSH operation is supposed to have
a value that is twice the normal timeout value. This patch preserves this
relationship while leveraging the flexibility of specifying the I/O timeout.
Based on a prior patch by KY Srinivasan <kys@microsoft.com>
Reviewed-by: KY Srinivasan <kys@microsoft.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Supports below logging facilities,
Inbound outbound queues dump.
Non fatal dump in case of IO failures.
Fatal dump in case of firmware failure.
[jejb: checkpatch spacing fixes]
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Phy profile implementation to support phy settings feature
for motherboard controllers.
[jejb: checkpatch fixes]
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
[jejb: checkpatch fixes]
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Firmware is having an issue. When a single IO request crosses
4G boundary, system will crash. To avoid the issue single sg is
converted into extended sg.
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fix for indirect data transfer mode in case of SMP request.
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Updated pci id table with device, vendor, subdevice and subvendor ids
for 8074, 8076, 8077 SAS/SATA 12G controllers. Added 12G related macros.
Signed-off-by: Anandkumar.Santhanam@pmcs.com
Reviewed-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It seems some iSCSI targets (including the Linux kernel target) close
the TCP connection from the target side immediately after processing a
session logout.
When a TCP FIN comes in right after the iSCSI logout response,
iscsi_sw_sk_state_check sees the local socket as not yet being in
CLOSE_WAIT or CLOSE and logs an error. But the initiator would close
the connection right after processing the logout response anyway, and
the error is confusing to admins who just requested that the session be
shut down.
This adds a check of the session state, and suppresses the error if we
are in the process of logging out.
Signed-off-by: Chris Leech <cleech@redhat.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It makes no sense to flush the cache of a device without medium.
Errors during suspend must be handled according to their causes.
Errors due to missing media or unplugged devices must be ignored.
Errors due to devices being offlined must also be ignored.
The error returns must be modified so that the generic layer
understands them.
[jejb: fix up whitespace and other formatting problems]
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Somehow older areca firmware versions have issues with
scsi_get_vpd_page() and a large buffer, the firmware
seems to crash and the scsi error-handler will start endless
recovery retries.
Limiting the buf-size to 64-bytes fixes this issue with older
firmware versions (<1.49 for my controller).
Fixes a regression with areca controllers and older firmware versions
introduced by commit: 66c28f9712
Reported-by: Nix <nix@esperi.org.uk>
Tested-by: Nix <nix@esperi.org.uk>
Signed-off-by: Bernd Schubert <bernd.schubert@itwm.fraunhofer.de>
Cc: stable@vger.kernel.org # delay inclusion for 2 months for testing
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Each member in data integrity field tuple is big-endian. But the
endianness of the values being compared with these members are not
annotated. So this fixes these sparse warnings.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the module initialization, invalid value for guard module parameter
is detected by the following check:
if (scsi_debug_guard > 1) {
printk(KERN_ERR "scsi_debug_init: guard must be 0 or 1\n");
return -EINVAL;
}
But this check isn't enough, because the type of scsi_debug_guard is
'int' and scsi_debug_guard could be a negative value.
This fixes it by changing the type of scsi_debug_guard to 'unsigned int'
instead of adding extra check for a negative value.
Reported-by: Joe Perches <joe@perches.com>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If data integrity support is enabled, prot_verify_write() is called in
response to WRITE commands and it verifies protection info from
prot_sglist by comparing against data sglist, and copies protection info
to dif_storep.
When multiple blocks are transfered by a WRITE command, it verifies and
copies these blocks one by one. So if it fails to verify protection
info in the middle of blocks, the actual data transfer to fake_storep
isn't proceeded at all although protection info for some blocks are
already copied to dif_storep. Therefore, it breaks the data integrity
between fake_storep and dif_storep.
This fixes it by ensuring that copying protection info to dif_storep is
done after all blocks are successfully verified. Reusing dif_copy_prot()
with supporting the opposite direction simplifies this fix.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If data integrity support is enabled, prot_verify_read() is called in
response to READ commands and it verifies protection info from dif_storep
by comparing against fake_storep, and copies protection info to
prot_sglist.
This factors out the portion of copying protection info into a separate
function. It will also be reused in the next change after supporting
the opposite direction (copying prot_sglist to dif_storep).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If the module parameter virtual_gb is greater than 0, the READ command
may request the blocks which exceed actual ramdisk storage (fake_storep).
prot_verify_read() should treat those blocks as wrap around the end of
fake_storep. But it actually causes fake_storep and dif_storep buffer
overruns.
This fixes these buffer overruns. In order to simplify the fix,
this also introduces fake_store() and dif_store() which return
corresponding wrap around addresses.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If certain configuration it is possible that ICD range is not page-aligned.
SGL posting failed in these configuration and driver load was not success.
This fix aligns ICD range values and SGL posting for IO is done.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Minh Tran <minhduc.tran@emulex.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When iSCSI stack invokes Abort or Reset handlers, the aborted tasks
Invalid Bit in WRB needs to be set. Else FW will not be aware of
the command invalidated which leads to BAD_WRB error posted by FW.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When MBX_Cmd completion happens with error code Insufficient Buffer,
the MBX_Cmd is posted again with the new buffer size posted by FW.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The MSIx to be created for SKH-R adapter should be based on
eq_count returned by get_fw_config.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Display CID available on each iSCSI Fn which can be used to
offload a connection. The display is split across available CID
on each chute.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The connection is offload to each chute in a round-robin manner
if both the chute is loaded with iSCSI protocol
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Configuration parameters returns the number of connection that
can be offloaded one each chute.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Configuration parameters return number of CID each chute supports. The WRB_Q
is created for the passed CID count. If both the Chute has iSCSI Protocol then
WRB_Q creation is in a round robin mechanism.
For BE-X family iSCSI protocol is loaded only on single chute.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Initialization of SGL and related PAGE posting is to be done for the chute.
Based on configuration value of each Chute,SGL initialization and page posting
is done.
For BE-X family iSCSI protocol is loaded only on single chute
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Template HDR is created for each chute which has iSCSI Protocol loaded.
For BE-X family iSCSI protocol is loaded only on single chute.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
DEF_Q[HDR/DATA] is created on the chute on which iSCSI Protocol is loaded.
When a connection is offloaded, the DEF_Q HDR/Data ID needs to be passed.
FW posts ASYNC message received from target on the passed DEF_Q. Connection
can be offloaded on any of the chute so DEF_Q is created on each Chute.
Change in the ASYNC path initialization based on the configuration parameters
returned for each chute.
For BE-X family iSCSI protocol is loaded only on single chute.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On the adapter iSCSI protocol can be loaded on either one or both
the CHUTE.Check on which CHUTE iSCSI Protocol is loaded and get
configuration parameters based on which driver initization is done.
For BE-X family iSCSI protocol is loaded only on single chute.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The timeout set in MBX_CMD is 100sec and the ready bit checking in BMBX
mode is done for 4sec. After 4sec the task is scheduled out for 5 secs
to avoid kernel soft lockup stack trace. The loop of 4sec ready bit check
and then schedule out is done until the following conditon occur
- The Ready Bit is Set
- The timeout set in MBX_CMD expires
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The default pdu is a common resource and needs to be protected
while manipulating it.
Signed-off-by: Minh Tran <minhduc.tran@emulex.com>
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
- Removed the check of MaxXmitDSL == 0 as this is not a possible
case.
- Update connection offload data structure for SKH-R adapters.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Storing MAC ADDR of each function in it's priv structure to
avoid issuing MAC_ADDR get IOCTL. Based on a flag set/unset
it's decided if MAC_ADDR is stored in priv structure or IOCTL
needs to be issued.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When MBX CMD is posted in MCCQ and if command times out,during
mccq resource cleanup for the timed out command mccq->count
was not decremented. The led to BUG_ON being hit.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allocating memory in the Host which will be used by the
TOE functionality during Session Offload. This fix will
allow performance improvement as adapter memory contention
will be reduced.
Signed-off-by: John Soni Jose <sony.john-n@emulex.com>
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
In the case when a SCSI_CMD times out, bnx2fc will initiate the sending of the
ABTS. However, if the SCSI layer's SCSI command timer also times out, it'll
instantiate a task abort of the same xid.
The race condition this patch tries to fix is as follows:
SCSI_CMD timeout (20s)
thread 1 thread 2
send ABTS
rx ABTS cmpl
task abort_eh
explicit LOGO since ABTS was engaged
CLEANUP cmpl
SCSI_CMD cmpl (ABTS cmpl)
instantiate RRQ
wait 10s
attempt to send RRQ (because of LOGO, it wouldn't continue)
Note that there is no call to scsi_done for this SCSI_CMD cmpletion
in this path.
The patch changes the path of execution to call scsi_done immediately
instead of instantiating the RRQ.
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add support to get local CHAP - index, username and password,
sysfs params of iscsi session corresponding to flash target entry.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Provide support to add/update the CHAP entries in adapter's flash
using iscsi tools, like Open-iSCSI.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For offload iSCSI like qla4xxx, CHAP entries are stored in adapter's
flash.
This patch adds support to add/update CHAP entries in adapter's flash
using iscsi tools, like Open-iSCSI.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
To write a CHAP entry in adapter's flash calculate the offset based
on the type of adapter.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If any flash target entry is using CHAP authentication then set
CHAP username and password sysfs params for the corresponding
iscsi sessions.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Support setting of CHAP_OUT_IDX param for the target entry in flash.
Setting of valid local CHAP index with enable CHAP AUTH for that
flash target entry and disabling CHAP AUTH will invalidate the CHAP
index for the flash target entry.
Signed-off-by: Adheer Chandravanshi <adheer.chandravanshi@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Earlier logic for driver created iscsi_session->discovery_parent_idx
was to store ram index of a sendtarget entry, but driver frees
sendtarget ram index as soon as firmware is done with discovery,
which is available for further use. So changing the logic to point
iscsi_session->discovery_parent_idx to store sendtarget flashnode index.
Signed-off-by: Manish Rangankar <manish.rangankar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed two issues in this patch-
1) In function megasas_get_pd_list(), data read(pd_addr->deviceId) from DMAed memory is converted to CPU's endianess.
2) While register AEN, removed some endianness conversion on some fields, since their endianess is already converted.
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added check for DMA mapping errors for request sense data
buffer. Checking for mapping error can avoid potential wild
writes. This patch was prompted by the warning from
dma_unmap when kernel is compiled with CONFIG_DMA_API_DEBUG.
Signed-off-by: Khalid Aziz <khalid.aziz@oracle.com>
Tested-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This feature gathers active and cumulative per fnic stats for io,
abort, terminate, reset, vlan discovery path and it also includes
various important stats for debugging issues. It also provided
debugfs and ioctl interface for user to retrieve these stats.
It also provides functionality to reset cumulative stats through
user interface.
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Fixed appropriate error codes that returns negative error number on failure,
and 0 on success. fnic_reset() is used directly by the fc transport callback
issue_fc_host_lip which requires a negative error number on failure.
Signed-off-by: Narsimhulu Musini <nmusini@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If you mutiple devices connect to a host, we might be interested in
have an intensive I/O workload on one disk, and notice starvation on others.
This give the user more hint about current infight io for scsi device.
Signed-off-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The PCIE capability offset is saved during PCI bus walking. It will
remove an unnecessary search in the PCI configuration space if this
value is referenced instead of reacquiring it. Also, pci_is_pcie is a
better way of determining if the device is PCIE or not (as it uses the
same saved PCIE capability offset).
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Acked-by: James Smart <james.smart@emulex.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Sujit has found a race condition that would make q->nr_pending
unbalanced, it occurs as Sujit explained:
"
sd_probe_async() ->
add_disk() ->
disk_add_event() ->
schedule(disk_events_workfn)
sd_revalidate_disk()
blk_pm_runtime_init()
return;
Let's say the disk_events_workfn() calls sd_check_events() which tries
to send test_unit_ready() and because of sd_revalidate_disk() trying to
send another commands the test_unit_ready() might be re-queued as the
tagged command queuing is disabled.
So the race condition is -
Thread 1 | Thread 2
sd_revalidate_disk() | sd_check_events()
...nr_pending = 0 as q->dev = NULL| scsi_queue_insert()
blk_runtime_pm_init() | blk_pm_requeue_request() ->
| nr_pending = -1 since
| q->dev != NULL
"
The problem is, the test_unit_ready request doesn't get counted the
first time it is queued, so the later decrement of q->nr_pending in
blk_pm_requeue_request makes it unbalanced.
Fix this by calling blk_pm_runtime_init before add_disk so that all
requests initiated there will all be counted.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reported-and-tested-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Cc: stable@vger.kernel.org
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If an invalid IOCB is returned on the response queue then the index into the
request queue map could be invalid and could return to us a bogus value. This
could cause us to try to deference an invalid pointer and cause an exception.
If we encounter this condition, simply return as no context can be established
for this response.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This lets the transport do endian conversion if necessary, and insulates
the drivers from the difference.
Most drivers can use the simple helpers virtio_cread() and virtio_cwrite().
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Just a dereference, don't need a macro.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Remove a lingering macro that just hid a dereference.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Andy Grover <agrover@redhat.com>
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Preliminary to removing compare_ether_addr altogether:
Use the new bool function ether_addr_equal to add
some clarity and reduce the likelihood for misuse
of compare_ether_addr for sorting.
Done via cocci script:
$ cat compare_ether_addr.cocci
@@
expression a,b;
@@
- !compare_ether_addr(a, b)
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- compare_ether_addr(a, b)
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) == 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !ether_addr_equal(a, b) != 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) == 0
+ !ether_addr_equal(a, b)
@@
expression a,b;
@@
- ether_addr_equal(a, b) != 0
+ ether_addr_equal(a, b)
@@
expression a,b;
@@
- !!ether_addr_equal(a, b)
+ ether_addr_equal(a, b)
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
In this pending patch:
http://patchwork.open-fcoe.org/patch/104/
Tomas Henzl noted that the error path when fcoe_fcf_device_add fails, was
missing a mutex_unlock call.
Not sure what staet the integration of the above patch is in, but if you could
either merge this with it, or apply it on top of what you already have, that
would be great. Thanks!
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
CC: thenzl@redhat.com
Reported-by: thenzl@redhat.com
Signed-off-by: Robert Love <robert.w.love@intel.com>
Correct common misspelling of "identify" as "indentify" throughout
the kernel
Signed-off-by: Maxime Jayat <maxime@artisandeveloppeur.fr>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Since commit 0998d06310
(device-core: Ensure drvdata = NULL when no driver is bound),
the driver core clears the driver data to NULL after device_release
or on probe failure. Thus, it is not needed to manually clear the
device driver data to NULL.
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Cc: James Bottomley <JBottomley@parallels.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Correct spelling typo within various part of the kernel
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
fnic doesn't use any of the create/destroy/enable/disable interfaces
either from the (legacy) module paramaters or the (new) fcoe_sysfs
interfaces. When fcoe_sysfs was introduced fnic wasn't changed since
it wasn't using the interfaces. libfcoe incorrectly assumed that that
all of its users were using fcoe_sysfs and when adding and deleting
FCFs would assume the existance of a fcoe_ctlr_device. fnic was not
allocating this structure because it doesn't care about the standard
user interfaces (fnic starts on link only). If/When libfcoe tried to use
the fcoe_ctlr_device's lock for the first time a NULL pointer exception
would be triggered.
Since fnic doesn't care about sysfs or user interfaces, the solution
is to drop libfcoe's assumption that all drivers are using fcoe_sysfs.
This patch accomplishes this by changing some of the structure
relationships.
We need a way to determine when a LLD is using fcoe_sysfs or not and
we can do that by checking for the existance of the fcoe_ctlr_device.
Prior to this patch, it was assumed that the fcoe_ctlr structure was
allocated with the fcoe_ctlr_device and immediately followed it in
memory. To reach the fcoe_ctlr_device we would simply go back in memory
from the fcoe_ctlr to get the fcoe_ctlr_device.
Since fnic doesn't allocate the fcoe_ctlr_device, we cannot keep that
assumption. This patch adds a pointer from the fcoe_ctlr to the
fcoe_ctlr_device. For bnx2fc and fcoe we will continue to allocate the
two structures together, but then we'll set the ctlr->cdev pointer
to point at the fcoe_ctlr_device. fnic will not change and will continue
to allocate the fcoe_ctlr itself, and ctlr->cdev will remain NULL.
When libfcoe adds fcoe_fcf's to the fcoe_ctlr it will check if ctlr->cdev
is set and only if so will it continue to interact with fcoe_sysfs.
Signed-off-by: Robert Love <robert.w.love@intel.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Tested-by: Hiral Patel <hiralpat@cisco.com>
* pci/misc:
PCI: Remove unused PCI_MSIX_FLAGS_BIRMASK definition
PCI: acpiphp_ibm: Convert to dynamic debug
PCI: acpiphp: Convert to dynamic debug
PCI: Remove Intel Haswell D3 delays
PCI: Pass type, width, and prefetchability for window alignment
PCI: Document reason for using pci_is_root_bus()
PCI: Use pci_is_root_bus() to check for root bus
PCI: Remove unused "is_pcie" from pci_dev structure
PCI: Update pci_find_slot() description in pci.txt
[SCSI] qla2xxx: Use standard PCIe Capability Link register field names
PCI: Fix comment typo, remove unnecessary !! in pci_is_pcie()
PCI: Drop "setting latency timer" messages
I had a typo in a variable name for the previous patch (SCSI: fcoe:
convert bus code to use bus_group) that broke the build, this fixes
that.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The bus_attrs field of struct bus_type is going away soon, dev_groups
should be used instead. This converts the fcoe bus code to use the
correct field.
Cc: Robert Love <robert.w.love@intel.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Use the standard #defines for PCIe Link Capability register fields
rather than bare numbers. This also uses the new PCI Express Capability
accessor rather than reading the capability directly.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Acked-by: Giridhar Malavali <giridhar.malavali@qlogic.com>
pci_is_pcie() and pcie_capability_clear_and_set_word() make it trivial
to set the PCIe Completion Timeout, so just fold the
csio_set_pcie_completion_timeout() function into its caller.
[bhelgaas: changelog, fold csio_set_pcie_completion_timeout() into caller]
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Naresh Kumar Inna <naresh@chelsio.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jesper Juhl <jj@chaosbits.net>
Use pcie_get_readrq()/pcie_set_readrq() to simplify code.
Jon Mason proposed a similar patch a couple years ago (see below).
[bhelgaas: validate pcie_max_read_reqsz, add pointer to Jon's patch]
Reference: http://lkml.kernel.org/r/1309191190-14670-1-git-send-email-jdmason@kudzu.us
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Anil Gurumurthy <agurumur@brocade.com>
Cc: Vijaya Mohan Guvva <vmohan@brocade.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
The freeze and restore functions defined in virtio drivers are used
for suspend and hibernate, so CONFIG_PM_SLEEP is more appropriate than
CONFIG_PM. This patch replace all CONFIG_PM with CONFIG_PM_SLEEP for
virtio drivers that implement freeze and restore callbacks.
Signed-off-by: Aaron Lu <aaron.lu@intel.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Pull networking fixes from David Miller:
1) If the local_df boolean is set on an SKB we have to allocate a
unique ID even if IP_DF is set in the ipv4 headers, from Ansis
Atteka.
2) Some fixups for the new chipset support that went into the sfc
driver, from Ben Hutchings.
3) Because SCTP bypasses a good chunk of, and actually duplicates, the
logic of the ipv6 output path, some IPSEC things don't get done
properly. Integrate SCTP better into the ipv6 output path so that
these problems are fixed and such issues don't get missed in the
future either. From Daniel Borkmann.
4) Fix skge regressions added by the DMA mapping error return checking
added in v3.10, from Mikulas Patocka.
5) Kill some more IRQF_DISABLED references, from Michael Opdenacker.
6) Fix races and deadlocks in the bridging code, from Hong Zhiguo.
7) Fix error handling in tun_set_iff(), in particular don't leak
resources. From Jason Wang.
8) Prevent format-string injection into xen-netback driver, from Kees
Cook.
9) Fix regression added to netpoll ARP packet handling, in particular
check for the right ETH_P_ARP protocol code. From Sonic Zhang.
10) Try to deal with AMD IOMMU errors when using r8169 chips, from
Francois Romieu.
11) Cure freezes due to recent changes in the rt2x00 wireless driver,
from Stanislaw Gruszka.
12) Don't do SPI transfers (which can sleep) in interrupt context in
cw1200 driver, from Solomon Peachy.
13) Fix LEDs handling bug in 5720 tg3 chips already handled for 5719.
From Nithin Sujir.
14) Make xen_netbk_count_skb_slots() count the actual number of slots
that will be used, taking into consideration packing and other
issues that the transmit path will run into. From David Vrabel.
15) Use the correct maximum age when calculating the bridge
message_age_timer, from Chris Healy.
16) Get rid of memory leaks in mcs7780 IRDA driver, from Alexey
Khoroshilov.
17) Netfilter conntrack extensions were converted to RCU but are not
always freed properly using kfree_rcu(). Fix from Michal Kubecek.
18) VF reset recovery not being done correctly in qlcnic driver, from
Manish Chopra.
19) Fix inverted test in ATM nicstar driver, from Andy Shevchenko.
20) Missing workqueue destroy in cxgb4 error handling, from Wei Yang.
21) Internal switch not initialized properly in bgmac driver, from Rafał
Miłecki.
22) Netlink messages report wrong local and remote addresses in IPv6
tunneling, from Ding Zhi.
23) ICMP redirects should not generate socket errors in DCCP and SCTP.
We're still working out how this should be handled for RAW and UDP
sockets. From Daniel Borkmann and Duan Jiong.
24) We've had several bugs wherein the network namespace's loopback
device gets accessed after it is free'd, NULL it out so that we can
catch these problems more readily. From Eric W Biederman.
25) Fix regression in TCP RTO calculations, from Neal Cardwell.
26) Fix too early free of xen-netback network device when VIFs still
exist. From Paul Durrant.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (87 commits)
netconsole: fix a deadlock with rtnl and netconsole's mutex
netpoll: fix NULL pointer dereference in netpoll_cleanup
skge: fix broken driver
ip: generate unique IP identificator if local fragmentation is allowed
ip: use ip_hdr() in __ip_make_skb() to retrieve IP header
xen-netback: Don't destroy the netdev until the vif is shut down
net:dccp: do not report ICMP redirects to user space
cnic: Fix crash in cnic_bnx2x_service_kcq()
bnx2x, cnic, bnx2i, bnx2fc: Fix bnx2i and bnx2fc regressions.
vxlan: Avoid creating fdb entry with NULL destination
tcp: fix RTO calculated from cached RTT
drivers: net: phy: cicada.c: clears warning Use #include <linux/io.h> instead of <asm/io.h>
net loopback: Set loopback_dev to NULL when freed
batman-adv: set the TAG flag for the vid passed to BLA
netfilter: nfnetlink_queue: use network skb for sequence adjustment
net: sctp: rfc4443: do not report ICMP redirects to user space
net: usb: cdc_ether: use usb.h macros whenever possible
net: usb: cdc_ether: fix checkpatch errors and warnings
net: usb: cdc_ether: Use wwan interface for Telit modules
ip6_tunnels: raddr and laddr are inverted in nl msg
...
commit b9871bcfd2
bnx2x: VF RSS support - PF side
changed the configuration of the doorbell HW and it broke iSCSI and FCoE.
We fix this by making compatible changes to the doorbell address in bnx2i
and bnx2fc. For the userspace driver, we need to pass a modified CID
so that the existing userspace driver will calculate the correct doorbell
address and continue to work.
Signed-off-by: Ariel Elior <ariele@broadcom.com>
Signed-off-by: Eddie Wai <eddie.wai@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch set is a set of driver updates (megaraid_sas, fnic, lpfc, ufs,
hpsa) we also have a couple of bug fixes (sd out of bounds and ibmvfc error
handling) and the first round of esas2r checker fixes and finally the much
anticipated big endian additions for megaraid_sas.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSNheiAAoJEDeqqVYsXL0MueMIAKD1kaB0oooRawE1+0vpKmyV
eE2M6trA8ofTeq0z1eNfRsVMkRsUuG9exW0CKS2z6mHiWwQ/zGbqT7ukveW+dMi3
mjKD0yO5ODk6bohWX/LiwZ6NGZSwC0dbIacXNy5ZsXKEizqwo1Jcc7qC/0AWn+o7
WpIL48XLPH0HqjQZ3dvgC6TWeFZOn9cKOWvQQq0S3ENALOx/eLZ+C7VrJLx5Magv
myNOUkTLzdlYglQfjaNO6et98k2oHTrzKwH7U2X6U75q7L8Pkj4RbNzce/Ge301V
u+R1w+BlbeTPdHopTBoTJupsvqDYBZxVwS7rr8nhSvfKduQppHnN6jX8yR4XNeM=
=RG3j
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull misc SCSI driver updates from James Bottomley:
"This patch set is a set of driver updates (megaraid_sas, fnic, lpfc,
ufs, hpsa) we also have a couple of bug fixes (sd out of bounds and
ibmvfc error handling) and the first round of esas2r checker fixes and
finally the much anticipated big endian additions for megaraid_sas"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (47 commits)
[SCSI] fnic: fnic Driver Tuneables Exposed through CLI
[SCSI] fnic: Kernel panic while running sh/nosh with max lun cfg
[SCSI] fnic: Hitting BUG_ON(io_req->abts_done) in fnic_rport_exch_reset
[SCSI] fnic: Remove QUEUE_FULL handling code
[SCSI] fnic: On system with >1.1TB RAM, VIC fails multipath after boot up
[SCSI] fnic: FC stat param seconds_since_last_reset not getting updated
[SCSI] sd: Fix potential out-of-bounds access
[SCSI] lpfc 8.3.42: Update lpfc version to driver version 8.3.42
[SCSI] lpfc 8.3.42: Fixed issue of task management commands having a fixed timeout
[SCSI] lpfc 8.3.42: Fixed inconsistent spin lock usage.
[SCSI] lpfc 8.3.42: Fix driver's abort loop functionality to skip IOs already getting aborted
[SCSI] lpfc 8.3.42: Fixed failure to allocate SCSI buffer on PPC64 platform for SLI4 devices
[SCSI] lpfc 8.3.42: Fix WARN_ON when driver unloads
[SCSI] lpfc 8.3.42: Avoided making pci bar ioremap call during dual-chute WQ/RQ pci bar selection
[SCSI] lpfc 8.3.42: Fixed driver iocbq structure's iocb_flag field running out of space
[SCSI] lpfc 8.3.42: Fix crash on driver load due to cpu affinity logic
[SCSI] lpfc 8.3.42: Fixed logging format of setting driver sysfs attributes hard to interpret
[SCSI] lpfc 8.3.42: Fixed back to back RSCNs discovery failure.
[SCSI] lpfc 8.3.42: Fixed race condition between BSG I/O dispatch and timeout handling
[SCSI] lpfc 8.3.42: Fixed function mode field defined too small for not recognizing dual-chute mode
...
Pull SCSI target updates from Nicholas Bellinger:
"Lots of activity again this round for I/O performance optimizations
(per-cpu IDA pre-allocation for vhost + iscsi/target), and the
addition of new fabric independent features to target-core
(COMPARE_AND_WRITE + EXTENDED_COPY).
The main highlights include:
- Support for iscsi-target login multiplexing across individual
network portals
- Generic Per-cpu IDA logic (kent + akpm + clameter)
- Conversion of vhost to use per-cpu IDA pre-allocation for
descriptors, SGLs and userspace page pointer list
- Conversion of iscsi-target + iser-target to use per-cpu IDA
pre-allocation for descriptors
- Add support for generic COMPARE_AND_WRITE (AtomicTestandSet)
emulation for virtual backend drivers
- Add support for generic EXTENDED_COPY (CopyOffload) emulation for
virtual backend drivers.
- Add support for fast memory registration mode to iser-target (Vu)
The patches to add COMPARE_AND_WRITE and EXTENDED_COPY support are of
particular significance, which make us the first and only open source
target to support the full set of VAAI primitives.
Currently Linux clients are lacking upstream support to actually
utilize these primitives. However, with server side support now in
place for folks like MKP + ZAB working on the client, this logic once
reserved for the highest end of storage arrays, can now be run in VMs
on their laptops"
* 'for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending: (50 commits)
target/iscsi: Bump versions to v4.1.0
target: Update copyright ownership/year information to 2013
iscsi-target: Bump default TCP listen backlog to 256
target: Fix >= v3.9+ regression in PR APTPL + ALUA metadata write-out
iscsi-target; Bump default CmdSN Depth to 64
iscsi-target: Remove unnecessary wait_for_completion in iscsi_get_thread_set
iscsi-target: Add thread_set->ts_activate_sem + use common deallocate
iscsi-target: Fix race with thread_pre_handler flush_signals + ISCSI_THREAD_SET_DIE
target: remove unused including <linux/version.h>
iser-target: introduce fast memory registration mode (FRWR)
iser-target: generalize rdma memory registration and cleanup
iser-target: move rdma wr processing to a shared function
target: Enable global EXTENDED_COPY setup/release
target: Add Third Party Copy (3PC) bit in INQUIRY response
target: Enable EXTENDED_COPY setup in spc_parse_cdb
target: Add support for EXTENDED_COPY copy offload emulation
target: Avoid non-existent tg_pt_gp_mem in target_alua_state_check
target: Add global device list for EXTENDED_COPY
target: Make helpers non static for EXTENDED_COPY command setup
target: Make spc_parse_naa_6h_vendor_specific non static
...
Introduced module params to provide dynamic way of configuring
queue depth.
Added support to get max io throttle count through UCSM to
configure maximum outstanding IOs supported by fnic and push
that value to scsi mid-layer.
Supported IO throttle values:
UCSM IO THROTTLE VALUE FNIC MAX OUTSTANDING IOS
------------------------------------------------------
16 (Default) 2048
<= 256 256
> 256 <ucsm value>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Kernel panics due to NULL lport while executing the log message because
of synchronization issues between libfc and scsi transport fc. Checking
for NULL pointers at the beginning of this routine would resolve the issue
from kernel panic point of view.
Signed-off-by: Sesidhar Baddel <sebaddel@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Hitting BUG_ON(io_req->abts_done) in fnic_rport_exch_reset in case of
timing issue and also to some extent locking issue where abts and terminate
is happening around same timing.
The code changes are intended to update CMD_STATE(sc) and
io_req->abts_done together.
Signed-off-by: Sesidhar Beddel <sebaddel@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Remove fnic driver QUEUE_FULL handling code instead let SCSI mid layer
handle queue full and use its algorithm to ramp down/up queue
Signed-off-by: Suma Ramars <sramars@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Issue was seen when SCSI buffer address is more than 40 bits in system
with more than 1.1TB RAM. When SCSI buffer is passed to VIC, it is failing
to map to correct buffer address, as DMA mask is set to 40 bits in driver
initialization. Corrected DMA_MASK from 40-bits to 64-bits to avoid masking
41-64 bits addresses.
Signed-off-by: Brian Uchino <buchino@cisco.com>
Signed-off-by: Hiral Patel <hiralpat@cisco.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch fixes an out-of-bounds error in sd_read_cache_type(), found
by Google's AddressSanitizer tool. When the loop ends, we know that
"offset" lies beyond the end of the data in the buffer, so no Caching
mode page was found. In theory it may be present, but the buffer size
is limited to 512 bytes.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
CC: <stable@vger.kernel.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Update copyright ownership/year information for target-core,
loopback, iscsi-target, tcm_qla2xx, vhost and iser-target.
Signed-off-by: Nicholas Bellinger <nab@linux-iscsi.org>
Reversing the dma_data_direction for pci_map_sg() friends is useful
for other drivers, so move it from tcm_qla2xxx into inline code
within target_core_fabric.h.
Also drop internal usage of equivlient in tcm_qla2xxx fabric code.
Reported-by: Christoph Hellwig <hch@lst.de>
Cc: Roland Dreier <roland@purestorage.com>
Cc: Giridhar Malavali <giridhar.malavali@qlogic.com>
Cc: Chad Dupuis <chad.dupuis@qlogic.com>
Cc: Nicholas Bellinger <nab@linux-iscsi.org>
Signed-off-by: Nicholas Bellinger <nab@daterainc.com>
This patch will add big endian architecture support to megaraid_sas
driver. The support added is for LSI MegaRAID all generation controllers-
(3Gb/s, 6Gb/s and 12 Gb/s controllers).
We have done basic sanity test @ppc64 arch and @x86_64. Additional
testing/observations are welcome.
[jejb: fix up rejections]
Signed-off-by: Kashyap Desai <kashyap.desai@lsi.com>
Signed-off-by: Sumit Saxena <sumit.saxena@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The prototype for ahc_9005_subdevinfo_valid shows that the caller has the
arguments in the wrong order.
637 ahc_9005_subdevinfo_valid(uint16_t device, uint16_t vendor,
638 uint16_t subdevice, uint16_t subvendor)
Signed-off-by: Dave Jones <davej@fedoraproject.org>
Acked-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Changes the version of hpsa so we know something has changed. Please consider
this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch does a bit of housekeeping for hpsa. Change lowercase alpha hex
digits to uppercase for consistency within the driver. Also moves the P822se
in the tables to keep controllers of each family grouped together.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add the marketing names for HP Smart Array Gen8 controllers. Also removes an
unused ID. Please consider this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch adds the PCI ID's for HP Smart Array Gen9 controllers. Please
consider this patch for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
UIC attributes can be set with using DME_SET command for
power mode change. For configuration the link capability
attributes are used, which is updated after successful
link startup.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Setting PA_PWRMode using DME_SET triggers the power mode
change. And then the result will be given by the HCS.UPMCRS.
This operation should be done atomically.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Implements to support GET and SET operations of the DME.
These operations are used to configure the behavior of
the UNIPRO. Along with basic operation, {Peer/AttrSetType}
can be mixed.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
IACTH(Interrupt aggregation counter threshold) value is allowed
up to 0x1F and current setting value is the maximum.
This value is related with NUTRS(max:0x20) of HCI's capability.
Considering HCI controller doesn't support the maximum, IACTH
setting should be adjusted with possible value.
For that, existing 'ufshcd_config_int_aggr' is split into two part
[reset, configure].
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Unlike 'GOOD' and 'CHECK CONDITION', other status values in
Response UPIU may or may not contain sense data. That is returning
sense data isn't obvious. So, in this case the Data Segment Length
field should be checked. If a non-zero value, it means that UPIU
has Sense Data in the Data Segment area.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Subhash Jadavani <subhashj@codeaurora.org>
Tested-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Right now the Makefile for the mpt3sas driver does not even allow the
driver to be built into the kernel. So fix that up, as there doesn't
seem to be any obvious reason why this shouldn't be done.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This fixes an issue seen with devices getting marked offline
in a scenario where a VIOS was getting rebooted while a
client VFC adapter is in SCSI EH and prevents unnecessary
EH escalation in some scenarios.
Signed-off-by: Brian King <brking@linux.vnet.ibm.com>
Acked-by: Robert Jennings <rcj@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The hypervisor is big endian, so little endian kernel builds need
to byteswap.
[jejb: fix checkpatch errors]
Signed-off-by: Anton Blanchard <anton@samba.org>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reported-by: Dave Jones <davej@redhat.com>
Signed-off-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Pull trivial tree from Jiri Kosina:
"The usual trivial updates all over the tree -- mostly typo fixes and
documentation updates"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial: (52 commits)
doc: Documentation/cputopology.txt fix typo
treewide: Convert retrun typos to return
Fix comment typo for init_cma_reserved_pageblock
Documentation/trace: Correcting and extending tracepoint documentation
mm/hotplug: fix a typo in Documentation/memory-hotplug.txt
power: Documentation: Update s2ram link
doc: fix a typo in Documentation/00-INDEX
Documentation/printk-formats.txt: No casts needed for u64/s64
doc: Fix typo "is is" in Documentations
treewide: Fix printks with 0x%#
zram: doc fixes
Documentation/kmemcheck: update kmemcheck documentation
doc: documentation/hwspinlock.txt fix typo
PM / Hibernate: add section for resume options
doc: filesystems : Fix typo in Documentations/filesystems
scsi/megaraid fixed several typos in comments
ppc: init_32: Fix error typo "CONFIG_START_KERNEL"
treewide: Add __GFP_NOWARN to k.alloc calls with v.alloc fallbacks
page_isolation: Fix a comment typo in test_pages_isolated()
doc: fix a typo about irq affinity
...
Pull sparc changes from David Miller:
"Several bug fixes (from Kirill Tkhai, Geery Uytterhoeven, and Alexey
Dobriyan) and some support for Fujitsu sparc64x chips (from Allen
Pais)"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/sparc:
sparc64: Export flush_ptrace_access() (needed by lustre)
sparc: fix PCI device proc file mmap(2)
sparc64: Remove RWSEM export leftovers
sparc64: Fix off by one in trampoline TLB mapping installation loop.
sparc64: Fix ITLB handler of null page
esp_scsi: Fix tag state corruption when autosensing.
sparc64: Fix not SRA'ed %o5 in 32-bit traced syscall
sparc64: cleanup: Rename ret_from_syscall to ret_from_fork
sparc32: Fix exit flag passed from traced sys_sigreturn
sparc64: Fix wrong syscall return value passed to trace_sys_exit()
support sparc64x chip type in cpumap.c
cpu hw caps support for sparc64x
Pull networking changes from David Miller:
"Noteworthy changes this time around:
1) Multicast rejoin support for team driver, from Jiri Pirko.
2) Centralize and simplify TCP RTT measurement handling in order to
reduce the impact of bad RTO seeding from SYN/ACKs. Also, when
both timestamps and local RTT measurements are available prefer
the later because there are broken middleware devices which
scramble the timestamp.
From Yuchung Cheng.
3) Add TCP_NOTSENT_LOWAT socket option to limit the amount of kernel
memory consumed to queue up unsend user data. From Eric Dumazet.
4) Add a "physical port ID" abstraction for network devices, from
Jiri Pirko.
5) Add a "suppress" operation to influence fib_rules lookups, from
Stefan Tomanek.
6) Add a networking development FAQ, from Paul Gortmaker.
7) Extend the information provided by tcp_probe and add ipv6 support,
from Daniel Borkmann.
8) Use RCU locking more extensively in openvswitch data paths, from
Pravin B Shelar.
9) Add SCTP support to openvswitch, from Joe Stringer.
10) Add EF10 chip support to SFC driver, from Ben Hutchings.
11) Add new SYNPROXY netfilter target, from Patrick McHardy.
12) Compute a rate approximation for sending in TCP sockets, and use
this to more intelligently coalesce TSO frames. Furthermore, add
a new packet scheduler which takes advantage of this estimate when
available. From Eric Dumazet.
13) Allow AF_PACKET fanouts with random selection, from Daniel
Borkmann.
14) Add ipv6 support to vxlan driver, from Cong Wang"
Resolved conflicts as per discussion.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1218 commits)
openvswitch: Fix alignment of struct sw_flow_key.
netfilter: Fix build errors with xt_socket.c
tcp: Add missing braces to do_tcp_setsockopt
caif: Add missing braces to multiline if in cfctrl_linkup_request
bnx2x: Add missing braces in bnx2x:bnx2x_link_initialize
vxlan: Fix kernel panic on device delete.
net: mvneta: implement ->ndo_do_ioctl() to support PHY ioctls
net: mvneta: properly disable HW PHY polling and ensure adjust_link() works
icplus: Use netif_running to determine device state
ethernet/arc/arc_emac: Fix huge delays in large file copies
tuntap: orphan frags before trying to set tx timestamp
tuntap: purge socket error queue on detach
qlcnic: use standard NAPI weights
ipv6:introduce function to find route for redirect
bnx2x: VF RSS support - VF side
bnx2x: VF RSS support - PF side
vxlan: Notify drivers for listening UDP port changes
net: usbnet: update addr_assign_type if appropriate
driver/net: enic: update enic maintainers and driver
driver/net: enic: Exposing symbols for Cisco's low latency driver
...
Conflicts:
drivers/net/ethernet/stmicro/stmmac/stmmac_platform.c
net/bridge/br_multicast.c
net/ipv6/sit.c
The conflicts were minor:
1) sit.c changes overlap with change to ip_tunnel_xmit() signature.
2) br_multicast.c had an overlap between computing max_delay using
msecs_to_jiffies and turning MLDV2_MRC() into an inline function
with a name using lowercase instead of uppercase letters.
3) stmmac had two overlapping changes, one which conditionally allocated
and hooked up a dma_cfg based upon the presence of the pbl OF property,
and another one handling store-and-forward DMA made. The latter of
which should not go into the new of_find_property() basic block.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch fixes the following compiler warning:
drivers/scsi/fcoe/fcoe_ctlr.c: In function fcoe_sysfs_fcf_add:
drivers/scsi/fcoe/fcoe_ctlr.c:211:1: warning: the frame size of 1480 bytes is larger than 1024 bytes [-Wframe-larger-than=]
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
FCoE debug statements must end in a newline. Add one where it is missing.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
The function fcoe_ctlr_mode_set() is local, hence declare it static.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
This patch avoids that the FCoE initiator sends a REC message after
having received a SCSI response with non-zero status and non-zero
DATA IN buffer length.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
While the FCoE initiator driver invokes fc_exch_done() from inside
the libfc response handler, FCoE target drivers typically invoke
fc_exch_done() from outside the libfc response handler. The object
fc_exch.arg points at may disappear as soon as fc_exch_done() has
finished. So it's important not to invoke the response handler
function after fc_exch_done() has finished. Modify libfc such that
this guarantee is provided if fc_exch_done() is invoked from
outside a response handler. This patch fixes a sporadic crash in
FCoE target implementations after a command has been aborted.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Reduce the time during which the exchange lock is held by allocating
a frame before obtaining the exchange lock.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Calling fc_seq_send() after an ABTS message has been received triggers
a kernel warning (WARN_ON(!(ep->esb_stat & ESB_ST_SEQ_INIT))). Avoid
this by returning -ENXIO to the caller if fc_seq_send() is invoked after
an ABTS message has been received.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
This patch avoids that the WARN_ON(!(ep->esb_stat & ESB_ST_SEQ_INIT))
statement in fc_seq_send_locked() gets triggered sporadically when
running FCoE target code due to concurrent ep->esb_stat modifications.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
It is allowed to pass a zero timeout value to fc_seq_exch_abort().
Avoid that this can cause the timeout function to drop the exchange
reference before it has been increased by fc_exch_timer_set_locked().
This patch fixes a crash when running FCoE target code with poisoning
enabled in the memory allocator.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
The condition ep != NULL && ep->xid != xid can never be met. Make
this explicit.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Convert a loop into an ilog2() call. Although this code is not performance
sensitive this conversion makes this code easier to read.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
The second argument of fc_lport_error() may be a valid frame pointer.
Hence only print it as an error code if it really is an error code.
Debug statements must end in a newline. Add one where it is missing.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Cc: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Change 'initiaive' into 'initiative', 'remainig' into 'remaining'
and change 'exected' into 'expected'.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Robert Love <robert.w.love@intel.com>
the return codes from fcoe_rcv should be NET_RX_*, not 0 or -1.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Based on my last patch I noticed that fcoe_rcv has a simmilar problem, in that
it manipulates the passed in skb without checking to see if it has other users.
Making manipulations to a shared skb can result in various corruptions.
Easy fix, just make sure the skb is unshared prior to doing anything with it.
Signed-off-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: Robert Love <robert.w.love@intel.com>
Pull libata changes from Tejun Heo:
"Two interesting changes.
- libata acpi handling has been restructured so that the association
between ata devices and ACPI handles are less convoluted. This
change shouldn't change visible behavior.
- Queued TRIM support, which enables sending TRIM to the device
without draining in-flight RW commands, is added. Currently only
enabled for ahci (and likely to stay that way for the foreseeable
future).
Other changes are driver-specific updates / fixes"
* 'for-3.12' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: bugfix: Remove __le32 in ata_tf_to_fis()
libata: acpi: Remove ata_dev_acpi_handle stub in libata.h
libata: Add support for queued DSM TRIM
libata: Add support for SEND/RECEIVE FPDMA QUEUED
libata: Add H2D FIS "auxiliary" port flag
libata: Populate host-to-device FIS "auxiliary" field
ata: acpi: rework the ata acpi bind support
sata, highbank: send extra clock cycles in SGPIO patterns
sata, highbank: set tx_atten override bits
devicetree: create a separate binding description for sata_highbank
drivers/ata/sata_rcar.c: simplify use of devm_ioremap_resource
sata highbank: enable 64-bit DMA mask when using LPAE
ata: pata_samsung_cf: add missing __iomem annotation
ata: pata_arasan: Staticize local symbols
sata_mv: Remove unneeded CONFIG_HAVE_CLK ifdefs
ata: use dev_get_platdata()
sata_mv: Remove unneeded forward declaration
libata: acpi: remove dead code for ata_acpi_(un)bind
libata: move 'struct ata_taskfile' and friends from ata.h to libata.h
This patch set is a set of driver updates (ufs, zfcp, lpfc, mpt2/3sas,
qla4xxx, qla2xxx [adding support for ISP8044 + other things]) we also have a
new driver: esas2r which has a number of static checker problems, but which I
expect to resolve over the -rc course of 3.12 under the new driver exception.
We also have the error return updates that were discussed at LSF.
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)
iQEcBAABAgAGBQJSJfX5AAoJEDeqqVYsXL0M8u8H+gN65iA4YeNc3Eq9F6mliLfg
JOIfn6GRz7ChbQ1ZZKdH/5xCOtzXphrkg7kRGmr9frsvYZ4X2c7W3xweQTA08gqP
wPH7/xyPffPnUm/r+V+SV41pm39bEjmltknLwiF572a6iOoVYQpnmDjdZQKT0jU0
QZEqI81+646m8edCnApLw3Tlsn2gBwHaDrkd55H2IQGTkOD016C0CQbM+cNMU440
qdqDcfRWCsp1fhLo3JH2kWTx8BihhyfEYAFz4tZwuFdGGkRZxF20HwyzV0h3hZOG
kZ2Gd1BFf0SybxOcESQmAukbcH5hyumX1Y7HMYKZbS2ubD4MCO1MO8UUtLXlxNc=
=PDBQ
-----END PGP SIGNATURE-----
Merge tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull first round of SCSI updates from James Bottomley:
"This patch set is a set of driver updates (ufs, zfcp, lpfc, mpt2/3sas,
qla4xxx, qla2xxx [adding support for ISP8044 + other things]).
We also have a new driver: esas2r which has a number of static checker
problems, but which I expect to resolve over the -rc course of 3.12
under the new driver exception.
We also have the error return that were discussed at LSF"
* tag 'scsi-misc' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi: (118 commits)
[SCSI] sg: push file descriptor list locking down to per-device locking
[SCSI] sg: checking sdp->detached isn't protected when open
[SCSI] sg: no need sg_open_exclusive_lock
[SCSI] sg: use rwsem to solve race during exclusive open
[SCSI] scsi_debug: fix logical block provisioning support when unmap_alignment != 0
[SCSI] scsi_debug: fix endianness bug in sdebug_build_parts()
[SCSI] qla2xxx: Update the driver version to 8.06.00.08-k.
[SCSI] qla2xxx: print MAC via %pMR.
[SCSI] qla2xxx: Correction to message ids.
[SCSI] qla2xxx: Correctly print out/in mailbox registers.
[SCSI] qla2xxx: Add a new interface to update versions.
[SCSI] qla2xxx: Move queue depth ramp down message to i/o debug level.
[SCSI] qla2xxx: Select link initialization option bits from current operating mode.
[SCSI] qla2xxx: Add loopback IDC-TIME-EXTEND aen handling support.
[SCSI] qla2xxx: Set default critical temperature value in cases when ISPFX00 firmware doesn't provide it
[SCSI] qla2xxx: QLAFX00 make over temperature AEN handling informational, add log for normal temperature AEN
[SCSI] qla2xxx: Correct Interrupt Register offset for ISPFX00
[SCSI] qla2xxx: Remove handling of Shutdown Requested AEN from qlafx00_process_aen().
[SCSI] qla2xxx: Send all AENs for ISPFx00 to above layers.
[SCSI] qla2xxx: Add changes in initialization for ISPFX00 cards with BIOS
...
Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem maintainers.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlIPcACgkQMUfUDdst+ynUMwCaAnITsxyDXYQ4DqEsz8EcOtMk
718AoLrgnUZs3B+70AT34DVktg4HSThk
=USl9
-----END PGP SIGNATURE-----
Merge tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core patches from Greg KH:
"Here's the big driver core pull request for 3.12-rc1.
Lots of tiny changes here fixing up the way sysfs attributes are
created, to try to make drivers simpler, and fix a whole class race
conditions with creations of device attributes after the device was
announced to userspace.
All the various pieces are acked by the different subsystem
maintainers"
* tag 'driver-core-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (119 commits)
firmware loader: fix pending_fw_head list corruption
drivers/base/memory.c: introduce help macro to_memory_block
dynamic debug: line queries failing due to uninitialized local variable
sysfs: sysfs_create_groups returns a value.
debugfs: provide debugfs_create_x64() when disabled
rbd: convert bus code to use bus_groups
firmware: dcdbas: use binary attribute groups
sysfs: add sysfs_create/remove_groups for when SYSFS is not enabled
driver core: add #include <linux/sysfs.h> to core files.
HID: convert bus code to use dev_groups
Input: serio: convert bus code to use drv_groups
Input: gameport: convert bus code to use drv_groups
driver core: firmware: use __ATTR_RW()
driver core: core: use DEVICE_ATTR_RO
driver core: bus: use DRIVER_ATTR_WO()
driver core: create write-only attribute macros for devices and drivers
sysfs: create __ATTR_WO()
driver-core: platform: convert bus code to use dev_groups
workqueue: convert bus code to use dev_groups
MEI: convert bus code to use dev_groups
...
Here is the big char/misc driver pull request for 3.12-rc1
Lots of driver updates all over the char/misc tree, full details in the
shortlog below.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.21 (GNU/Linux)
iEYEABECAAYFAlIlH58ACgkQMUfUDdst+ymTGwCdH1BmMdypyjUBxJEoWNDUuwXn
/AQAoKt329vmB6qn41rvaTilHHYUXS7H
=ovaW
-----END PGP SIGNATURE-----
Merge tag 'char-misc-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc patches from Greg KH:
"Here is the big char/misc driver pull request for 3.12-rc1
Lots of driver updates all over the char/misc tree, full details in
the shortlog"
* tag 'char-misc-3.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (62 commits)
drivers: uio: Kconfig: add MMU dependancy for UIO
drivers: uio: Add driver for Humusoft MF624 DAQ PCI card
drivers: uio_pdrv_genirq: use dev_get_platdata()
drivers: uio_pruss: use dev_get_platdata()
drivers: uio_dmem_genirq: use dev_get_platdata()
drivers: parport: Kconfig: exclude h8300 for PARPORT_PC
drivers: misc: ti-st: fix potential race if st_kim_start fails
Drivers: hv: vmbus: Do not attempt to negoatiate a new version prematurely
misc: vmw_balloon: Remove braces to fix build for clang.
Drivers: hv: vmbus: Fix a bug in the handling of channel offers
vme: vme_ca91cx42.c: fix to pass correct device identity to free_irq()
VMCI: Add support for virtual IOMMU
VMCI: Remove non-blocking/pinned queuepair support
uio: uio_pruss: remove unnecessary platform_set_drvdata()
parport: amiga: remove unnecessary platform_set_drvdata()
vme: vme_vmivme7805.c: add missing __iomem annotation
vme: vme_ca91cx42.c: add missing __iomem annotation
vme: vme_tsi148.c: add missing __iomem annotation
drivers/misc/hpilo: Correct panic when an AUX iLO is detected
uio: drop unused vma_count member in uio_device struct
...
Push file descriptor list locking down to per-device locking. Let sg_index_lock
only protect device lookup.
sdp->detached is also set and checked with this lock held.
Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
@detached is set under the protection of sg_index_lock. Without getting the
lock, new sfp will be added during sg removal and there is no chance for it
to be picked out. So check with sg_index_lock held in sg_add_sfp().
Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Open exclusive check is protected by o_sem, no need sg_open_exclusive_lock.
@exclude is used to record which type of rwsem we are holding.
Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
A race condition may happen if two threads are both trying to open the same sg
with O_EXCL simultaneously. It's possible that they both find fsds list is
empty and get_exclude(sdp) returns 0, then they both call set_exclude() and
break out from wait_event_interruptible and resume open.
Now use rwsem to protect this process. Exclusive open gets write lock and
others get read lock. The lock will be held until file descriptor is closed.
This also leads 'exclude' only a status rather than a check mark.
Signed-off-by: Vaughan Cao <vaughan.cao@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Commit b90ebc3d5c ("[SCSI] scsi_debug:
fix logical block provisioning support") fixed several issues with
logical block provisioning support, but it still doesn't properly fix
the cases when unmap_alignment > 0.
For example, load scsi_debug module with the following module parameters
and make all blocks mapped by filling the storage with zero.
# modprobe scsi_debug lbpu=1 unmap_alignment=1 unmap_granularity=4
# dd if=/dev/zero of=$DEV
Then, try to unmap the first unmappable blocks at lba=1, but GET LBA STATUS
unexpectedly reports that the last UNMAP has done nothing.
# sg_unmap --lba=1 --num=4 $DEV
# sg_get_lba_status --lba=1 $DEV
descriptor LBA: 0x0000000000000001 blocks: 16383 mapped
The problem is in map_index_to_lba(), which should return the first
LBA which is corresponding to a given index of provisioning map
(map_storep).
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
With module parameter num_parts > 0, partition table is built on the
ramdisk storage when loading the driver. Unfortunately, there is an
endianness bug in sdebug_build_parts(). So the partition table is not
correctly initialized on big-endian systems.
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Tested-by: Martin Peschke <mpeschke@linux.vnet.ibm.com>
Acked-by: Douglas Gilbert <dgilbert@interlog.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
At mailbox/buffer debug level, print the correct values of the
outgoing and incoming mailbox registers.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
On any Adapter when we flash through FC/FCoE without card reset option it still
shows the Running FW version in Flashed FW version. This new interface will be
used by API to instruct the driver to update its cache versions.
Signed-off-by: Sawan Chandak <sawan.chandak@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Unless there is a need to observe them, the queue depth ramp up/down messages
are a nuisance and may cause the system to become unresponsive so move it a
non-default logging level.
Signed-off-by: Chad Dupuis <chad.dupuis@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Earlier IDC-TIME-EXTEND aen was a nop and ignored by driver.
We now have to handle the aen so that other protocol drivers can use time
extension during some loopback operations.
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
For supported ISPS, Read asic temperature by calling the
GET PARAMS (type C) mailbox command.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
list_for_each_entry() never leaves the iterator pointing to null.
Signed-off-by: Joe Carnuccio <joe.carnuccio@qlogic.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The patch changes a specifier used to output some variables. Instead of using
stack for each byte the '%*ph[CN]' allows to take a one pointer and prints
entire buffer as a hexadecimal string with the separator ':' or ''.
Signed-off-by: Oleksandr Khoshaba <Oleksandr.Khoshaba@gmail.com>
Signed-off-by: Saurav Kashyap <saurav.kashyap@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This patch updates the firmware to address the thermal notification issue
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
This is a new driver for ATTO Technology's ExpressSAS series of hardware RAID
adapters. It supports the following adapters:
- ExpressSAS R60F
- ExpressSAS R680
- ExpressSAS R608
- ExpressSAS R644
Signed-off-by: Bradley Grove <bgrove@attotech.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Smatch complains that the reg_IRQ[] array only has MAXIRQ (16) elements
so we are one space beyond the end of the array here.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Return error from function qla4_8xxx_collect_md_data()
if minidump data collection fails.
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add pex-dma support for ISP8324 and ISP8042 to improve
the minidump capture time.
Signed-off-by: Santosh Vernekar <santosh.vernekar@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added a driver module parameter max_msix_vectors. Using this module parameter
the maximum number of MSI-X vectors could be set.
The number of MSI-X vectors used would be the minimum of MSI-X vectors
supported by the HBA, the number of CPU cores and the value set to
max_msix_vectors module parameter.
The default value of this module parameter is set to 8. The default value of
this parameter is set to 8 inorder to reduce the amount of memory required for
Reply Descriptor Post queue. This is because with the higher MSI-X vectors,
some times kernel is not able to allocate the requested amount of memory and
crash is observed. To overcome this problem, the default value is set to 8.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
While loopback diagnostic is in progress, disable the ACB which resets
all the active connections to target. Disable ACB would filter out all
the DHCP multicast and broadcast packets which otherwise cause the
diagnostic test to take longer time to complete or failures in some
other cases.
Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
With some enclosures when LUN 0 is not created but LUN 1 or LUN X is created
then SCSI scan procedure calls target_alloc, slave_alloc call back functions
for LUN 0 and slave_destory() for same LUN 0.
In these kind of cases within slave_destroy, pointer to scsi_target in
_sas_device structure is set to NULL, following which when slave_alloc for
LUN 1 is called then starget would not be set properly for this LUN.
So, scsi_target pointer pointing to NULL value would lead to a crash later
in the discovery procedure.
To solve this issue set the sas_device's scsi_target pointer to scsi_device's
scsi_target if it is NULL earlier in slave_alloc callback function.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When Async scanning mode is enabled and device scanning is in progress then
devices should not be removed. But in actuality, devices are removed but
their transport layer entries are not removed. This causes error to add
the same device to the transport layer after host reset or diagnostic
reset.
So, in this patch, modified the code in such a way that device is not removed
when Async scanning mode is enabled and device scanning is in progress.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Infinite loop can occur if IOCStatus is not equal to
MPI2_IOCSTATUS_CONFIG_INVALID_PAGE value in the while loops in functions
_scsih_search_responding_sas_devices,
_scsih_search_responding_raid_devices and
_scsih_search_responding_expanders
So, Instead of checking for MPI2_IOCSTATUS_CONFIG_INVALID_PAGE value,
in this patch code is modified to check for IOCStatus not equals to
MPI2_IOCSTATUS_SUCCESS to break the while loop.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The copyright in driver sources is updated for the year 2013.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Change set in MPI2 Rev x specification and 2.00.26 header files
1. Added two new AbortType values for TargetModeAbort Request: one to abort
all IOs from a single initiator and other to abort only Command IUs.
2. Added Use Slot Information during Port Enable Event Reply flag to the Flags
field of Manufacturing Page 7.
3. Added OEM Identifier to BiosOptions bits of BIOS Page 1.
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The intent of this patch is to perform a graceful shutdown of target drives even if
volume doesn't exits. Changes done in this patch
1. Removed the check for the presence of volumes before sending down
MPI2_RAID_ACTION_SYSTEM_SHUTDOWN_INITIATED. Therefore, this RAID action
would be sent if the card is IR Firmware.
2. The MPI2_RAID_ACTION_SYSTEM_SHUTDOWN_INITIATED is sent even when the
system undergoes suspend (in addition to remove/shutdown which was already
present)
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Added a check to identify if mpi_reply is NULL in mpt2sas_ctl_event_callback()
and return without proceeding if it is the case.
Also modified the following functions to return void instead of 0 or 1
as returning those values from events perspective doesn't make sense.
* _base_async_event()
* mpt2sas_ctl_event_callback()
* mpt2sas_scsih_event_callback()
Signed-off-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
section Signed-off-by: John Kacur <jkacur@redhat.com>
On a 3.6-rt (real-time patch) kernel we are seeing the following BUG
However, it appears to be relevant for non-realtime (mainline) as well.
[ 49.688847] hpsa 0000:03:00.0: hpsa0: <0x323a> at IRQ 67 using DAC
[ 49.749928] scsi0 : hpsa
[ 49.784437] BUG: using smp_processor_id() in preemptible [00000000
00000000] code: kworker/u:0/6
[ 49.784465] caller is enqueue_cmd_and_start_io+0x5a/0x100 [hpsa]
[ 49.784468] Pid: 6, comm: kworker/u:0 Not tainted
3.6.11.5-rt37.52.el6rt.x86_64.debug #1
[ 49.784471] Call Trace:
[ 49.784512] [<ffffffff812abe83>] debug_smp_processor_id+0x123/0x150
[ 49.784520] [<ffffffffa009043a>] enqueue_cmd_and_start_io+0x5a/0x100
[hpsa]
[ 49.784529] [<ffffffffa00905cb>]
hpsa_scsi_do_simple_cmd_core+0xeb/0x110 [hpsa]
[ 49.784537] [<ffffffff812b09c8>] ? swiotlb_dma_mapping_error+0x18/0x30
[ 49.784544] [<ffffffff812b09c8>] ? swiotlb_dma_mapping_error+0x18/0x30
[ 49.784553] [<ffffffffa0090701>]
hpsa_scsi_do_simple_cmd_with_retry+0x91/0x280 [hpsa]
[ 49.784562] [<ffffffffa0093558>]
hpsa_scsi_do_report_luns.clone.2+0xd8/0x130 [hpsa]
[ 49.784571] [<ffffffffa00935ea>]
hpsa_gather_lun_info.clone.3+0x3a/0x1a0 [hpsa]
[ 49.784580] [<ffffffffa00963df>] hpsa_update_scsi_devices+0x11f/0x4f0
[hpsa]
[ 49.784592] [<ffffffff81592019>] ? sub_preempt_count+0xa9/0xe0
[ 49.784601] [<ffffffffa00968ad>] hpsa_scan_start+0xfd/0x150 [hpsa]
[ 49.784613] [<ffffffff8158cba8>] ? rt_spin_lock_slowunlock+0x78/0x90
[ 49.784626] [<ffffffff813b04d7>] do_scsi_scan_host+0x37/0xa0
[ 49.784632] [<ffffffff813b05da>] do_scan_async+0x1a/0x30
[ 49.784643] [<ffffffff8107c4ab>] async_run_entry_fn+0x9b/0x1d0
[ 49.784655] [<ffffffff8106ae92>] process_one_work+0x1f2/0x620
[ 49.784661] [<ffffffff8106ae20>] ? process_one_work+0x180/0x620
[ 49.784668] [<ffffffff8106d4fe>] ? worker_thread+0x5e/0x3a0
[ 49.784674] [<ffffffff8107c410>] ? async_schedule+0x20/0x20
[ 49.784681] [<ffffffff8106d5d3>] worker_thread+0x133/0x3a0
[ 49.784688] [<ffffffff8106d4a0>] ? manage_workers+0x190/0x190
[ 49.784696] [<ffffffff81073236>] kthread+0xa6/0xb0
[ 49.784707] [<ffffffff815970a4>] kernel_thread_helper+0x4/0x10
[ 49.784715] [<ffffffff81082a7c>] ? finish_task_switch+0x8c/0x110
[ 49.784721] [<ffffffff8158e44b>] ? _raw_spin_unlock_irq+0x3b/0x70
[ 49.784727] [<ffffffff8158e85d>] ? retint_restore_args+0xe/0xe
[ 49.784734] [<ffffffff81073190>] ? kthreadd+0x1e0/0x1e0
[ 49.784739] [<ffffffff815970a0>] ? gs_change+0xb/0xb
-------------------
This is caused by
enqueue_cmd_and_start_io()->
set_performant_mode()->
smp_processor_id()
Which if you have debugging enabled calls debug_processor_id() and triggers the warning.
The code here is
c->Header.ReplyQueue = smp_processor_id() % h->nreply_queues;
Since it is not critical that the code complete on the same processor,
but the cpu is a hint used in generating the ReplyQueue and will still work if
the cpu migrates or is preempted, it is safe to use the raw_smp_processor_id()
to surpress the false positve warning.
Signed-off-by: John Kacur <jkacur@redhat.com>
Acked-by: Stephen Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
To run discovery over iSER we need to advertize the CAP_TEXT_NEGO capability
towards user space. Also need to make sure the login RX buffer is posted when
SendTargets TEXT PDUs are sent. For that end, we use a setting of the
ISCSI_PARAM_DISCOVERY_SESS iscsi param as an indication that this is
discovery session.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
PCI core will initialize device MSI/MSI-X capability in
pci_msi_init_pci_dev(). So device driver should use
pci_dev->msi_cap/msix_cap to determine whether the device
support MSI/MSI-X instead of using
pci_find_capability(pci_dev, PCI_CAP_ID_MSI/MSIX).
Access to PCIe device config space again will consume more time.
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Acked-by: lindar_liu <lindar_liu@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If mpt3sas_base_map_resources takes an early error path then its
counterpart, mpt3sas_base_free_resources needs to be careful about
cleaning up:
1 - _base_mask_interrupts and _base_make_ioc_ready require memory
mapped I/O registers, make sure that this is true.
2 - _base_free_irq iterates over the adapter's reply_queue_list, so
move this list head initialization out of _base_enable_msix to
_scsih_probe so this will always be safe.
3 - check that the controller PCI device and its BARs have been
enabled before disabling them.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
If mpt2sas_base_map_resources takes an early error path then its
counterpart, mpt2sas_base_free_resources needs to be careful about
cleaning up:
1 - _base_mask_interrupts and _base_make_ioc_ready require memory
mapped I/O registers, make sure that this is true.
2 - _base_free_irq iterates over the adapter's reply_queue_list, so
move this list head initialization out of _base_enable_msix to
_scsih_probe so this will always be safe.
3 - check that the controller PCI device and its BARs have been
enabled before disabling them.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: Sreekanth Reddy <Sreekanth.Reddy@lsi.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Generate a uevent when the following Unit Attention ASC/ASCQ
codes are received:
2A/01 MODE PARAMETERS CHANGED
2A/09 CAPACITY DATA HAS CHANGED
38/07 THIN PROVISIONING SOFT THRESHOLD REACHED
3F/03 INQUIRY DATA HAS CHANGED
3F/0E REPORTED LUNS DATA HAS CHANGED
Log kernel messages when the following Unit Attention ASC/ASCQ
codes are received that are not as specific as those above:
2A/xx PARAMETERS CHANGED
3F/xx TARGET OPERATING CONDITIONS HAVE CHANGED
Added logic to set expecting_lun_change for other LUNs on the target
after REPORTED LUNS DATA HAS CHANGED is received, so that duplicate
uevents are not generated, and clear expecting_lun_change when a
REPORT LUNS command completes, in accordance with the SPC-3
specification regarding reporting of the 3F 0E ASC/ASCQ UA.
[jejb: remove SPC3 test in scsi_report_lun_change and some docbook fixes and
unused variable fix, both reported by Fengguang Wu]
Signed-off-by: Ewan D. Milne <emilne@redhat.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
The IO command size is 128 bytes for these new controllers as opposed to 64
for the old 8001 controller.
The Adaptec out-of-tree driver did this correctly. After comparing the two
this turned out to be the crucial difference.
So don't hardcode the IO command size, instead use pm8001_ha->iomb_size as
that is the correct value for both old and new controllers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Acked-by: Anand Kumar Santhanam <AnandKumar.Santhanam@pmcs.com>
Acked-by: Jack Wang <xjtuwjp@gmail.com>
Cc: stable@vger.kernel.org # for v3.10 and up
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add the appropriate definitions and table entries for new adapter support.
Signed-off-by: Wen Xiong <wenxiong@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When the driver calls scsi_done and after that frees it's internal
preallocated memory it can happen that a new job is enqueud before
the memory is freed. The allocation fails and the message
"cmd_alloc returned NULL" is shown.
Patch below fixes it by moving cmd->scsi_done after cmd_free.
Signed-off-by: Tomas Henzl <thenzl@redhat.com>
Acked-by: Stephen M. Cameron <scameron@beardog.cce.hp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
It seems the "phy_index++;" have been placed in wrong place, without it
the while circle up will do a infinite loop.
Signed-off-by: Xinghai Yu <yuxinghai@cn.fujitsu.com>
Acked-by: Lukasz Dorau <lukasz.dorau@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
devm_ioremap_resource does sanity checks on the given resource. No need to
duplicate this in the driver.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
scsi_remove_host() sends SYNCHRONIZE CACHE commands for write cache
enabled scsi disk devices. So stopping controller working shouldn't
be done before scsi_remove_host().
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
When removing the UFS driver, disable_irq() is called and the IRQ is
not enabled again. Unfortunately, the IRQ is requested with IRQF_SHARED
and it can be shared among several devices. So disabling the IRQ in
this way is just breaking other devices which are sharing the IRQ.
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Before commit 2953f850c3 ("[SCSI] ufs:
use devres functions for ufshcd"), UFSHCI register was ioremapped by
each glue-driver (ufshcd-pltfrm and ufshcd-pci) during probing and it
was iounmapped by core-driver during removing driver. The commit
converted ufshcd-pltfrm to use devres functions, but it didn't convert
ufshcd-pci.
Therefore, the change causes ufshcd-pci driver not to iounmap UFSHCI
register region during removing driver. This fixes it by converting
ufshcd-pci to use devres functions.
Signed-off-by: Akinobu Mita <mita@fixstars.com>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Add runtime PM helpers to suspend/resume UFS controller at runtime.
Enable runtime PM by default for pci and platform drivers as the
initialized hardware can suspend if it is not used after bootup.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Background operations in the UFS device can be disabled by
the host to reduce the response latency of transfer requests.
Add support for enabling/disabling the background operations
during runtime suspend/resume of the device.
If the device is in critical need of BKOPS it will raise an
URGENT_BKOPS exception which should be handled by the host to
make sure the device performs as expected.
During bootup, the BKOPS is enabled in the device by default.
The disable of BKOPS is supported only when the driver supports
runtime suspend/resume operations as the runtime PM framework
provides a way to determine the device idleness and hence BKOPS
can be managed effectively. During runtime resume the BKOPS is
disabled to reduce latency and during runtime suspend the BKOPS
is enabled to allow device to carry out idle time BKOPS.
In some cases where the BKOPS is disabled during runtime resume
and due to continuous data transfers the runtime suspend is not
triggered, the BKOPS is enabled when the device raises a level-2
exception (outstanding operations - performance impact).
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
Allow UFS device to complete its initialization and accept
SCSI commands by setting fDeviceInit flag. The device may take
time for this operation and hence the host should poll until
fDeviceInit flag is toggled to zero. This step is mandated by
UFS device specification for device initialization completion.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
As part of device initialization sequence, sending NOP OUT UPIU and
waiting for NOP IN UPIU response is mandatory. This confirms that the
device UFS Transport (UTP) layer is functional and the host can configure
the device with further commands. Add support for sending NOP OUT UPIU to
check the device connection path and test whether the UTP layer on the
device side is functional during initialization.
A tag is acquired from the SCSI tag map space in order to send the device
management command. When the tag is acquired by internal command the scsi
command is rejected with host busy flag in order to requeue the request.
To avoid frequent collisions between internal commands and scsi commands
the device management command tag is allocated in the opposite direction
w.r.t block layer tag allocation.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Santosh Y <santoshsy@gmail.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>
James Smart