Commit Graph

278 Commits

Author SHA1 Message Date
Jussi Kivilinna 55f7782e14 zd1211rw: detect stalled beacon interrupt faster
As USB_INT_ID_RETRY_FAILED can override USB_INT_ID_REGS, beacon interrupt
(CR_INTERRUPT) might be lost. Problem is that when device trigger CR_INTERRUPT
it disables HW interrupt. Now if USB_INT_ID_REGS with CR_INTERRUPT gets lost,
beacon interrupt stays disabled until beacon watchdog notices the stall. This
happen very often on heavy TX. Improve watchdog to trigger earlier, after three
missing beacon interrupts.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22 16:09:47 -04:00
Jussi Kivilinna dde4673b8d zd1211rw: don't let zd_mac_config_beacon() run too long from beacon interrupt handler
zd_mac_config_beacon() has only limited time to set up beacon when called from
beacon interrupt handler/worker. So do not let it retry acquiring beacon fifo
semaphore in interrupt handler. Beacon fifo semaphore should not be locked by
firmware anyway at this time, it's only locked when device is using/txing
beacon.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22 16:09:46 -04:00
Jussi Kivilinna c900eff30a zd1211rw: handle lost read-reg interrupts
Device losses read-reg interrupts. By looking at usbmon it appears that
USB_INT_ID_RETRY_FAILED can override USB_INT_ID_REGS. This causes read
command to timeout, usually under heavy TX.

Fix by retrying read registers again if USB_INT_ID_RETRY_FAILED is received
while waiting for USB_INT_ID_REGS.

However USB_INT_ID_REGS is not always lost but is received after
USB_INT_ID_RETRY_FAILED and is usually received by the retried read
command. USB_INT_ID_REGS of the retry is then left unhandled and might
be received by next read command. Handle this by ignoring previous
USB_INT_ID_REGS that doesn't match current read command request.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22 16:09:46 -04:00
Jussi Kivilinna f762d8c3f8 zd1211rw: only update HW beacon if new beacon differs from currect
Update HW beacon only when needed. This appears to make device work in AP-mode
(dtim_period=1) somewhat more stable.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22 16:09:46 -04:00
Jussi Kivilinna b405e1b83d zd1211rw: make 'handle_rx_packet: invalid, small RX packet' message debug-only
This message is should be debug-only as it tells almost nothing useful. It also
happens very often and just floods logs.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22 16:09:45 -04:00
Jussi Kivilinna 7a1d6564a1 zd1211rw: fix invalid signal values from device
Driver uses IEEE80211_HW_SIGNAL_UNSPEC and so signal values reported to
mac80211 should be in range 0..100. Sometimes device return out of range
values. These out of range values can then trigger warning in
cfg80211_inform_bss_frame.

This patch adds checks to enforce range returned from driver to
mac80211 be in 0..100 range.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-22 16:09:45 -04:00
Kalle Valo 9a0669681c zd1211rw: include mac80211.h from zd_chip.h
zd_chip.h contains one function with a pointer to ieee80211_hw but doesn't
include mac80211.h. As a temporary solution include mac80211.h to avoid
a warning.

Signed-off-by: Kalle Valo <kvalo@adurom.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-06-20 15:16:32 -04:00
Jussi Kivilinna 59342f6a6b zd1211rw: fix to work on OHCI
zd1211 devices register 'EP 4 OUT' endpoint as Interrupt type on USB 2.0:

      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x04  EP 4 OUT
        bmAttributes            3
          Transfer Type            Interrupt
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               1

However on USB 1.1 endpoint becomes Bulk:

      Endpoint Descriptor:
        bLength                 7
        bDescriptorType         5
        bEndpointAddress     0x04  EP 4 OUT
        bmAttributes            2
          Transfer Type            Bulk
          Synch Type               None
          Usage Type               Data
        wMaxPacketSize     0x0040  1x 64 bytes
        bInterval               0

Commit 37939810b9 assumed that endpoint is
always interrupt type and changed usb_bulk_msg() calls to usb_interrupt_msg().

Problem here is that usb_bulk_msg() on interrupt endpoint selfcorrects the
call and changes requested pipe to interrupt type (see usb_bulk_msg).
However with usb_interrupt_msg() on bulk endpoint does not correct the
pipe type to bulk, but instead URB is submitted with interrupt type pipe.

So pre-2.6.39 used usb_bulk_msg() and therefore worked with both endpoint
types, however in 2.6.39 usb_interrupt_msg() with bulk endpoint causes
ohci_hcd to fail submitted URB instantly with -ENOSPC and preventing zd1211rw
from working with OHCI.

Fix this by detecting endpoint type and using correct endpoint/pipe types
for URB. Also fix asynchronous zd_usb_iowrite16v_async() to use right
URB type on 'EP 4 OUT'.

Cc: stable@kernel.org
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-05-31 14:47:26 -04:00
John W. Linville 252f4bf400 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 into for-davem
Conflicts:
	drivers/net/wireless/ath/ar9170/main.c
	drivers/net/wireless/ath/ar9170/phy.c
	drivers/net/wireless/zd1211rw/zd_rf_rf2959.c
2011-04-12 16:18:44 -04:00
Linus Torvalds c44eaf41a5 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (34 commits)
  net: Add support for SMSC LAN9530, LAN9730 and LAN89530
  mlx4_en: Restoring RX buffer pointer in case of failure
  mlx4: Sensing link type at device initialization
  ipv4: Fix "Set rt->rt_iif more sanely on output routes."
  MAINTAINERS: add entry for Xen network backend
  be2net: Fix suspend/resume operation
  be2net: Rename some struct members for clarity
  pppoe: drop PPPOX_ZOMBIEs in pppoe_flush_dev
  dsa/mv88e6131: add support for mv88e6085 switch
  ipv6: Enable RFS sk_rxhash tracking for ipv6 sockets (v2)
  be2net: Fix a potential crash during shutdown.
  bna: Fix for handling firmware heartbeat failure
  can: mcp251x: Allow pass IRQ flags through platform data.
  smsc911x: fix mac_lock acquision before calling smsc911x_mac_read
  iwlwifi: accept EEPROM version 0x423 for iwl6000
  rt2x00: fix cancelling uninitialized work
  rtlwifi: Fix some warnings/bugs
  p54usb: IDs for two new devices
  wl12xx: fix potential buffer overflow in testmode nvs push
  zd1211rw: reset rx idle timer from tasklet
  ...
2011-04-11 07:27:24 -07:00
John W. Linville b37e3b6d64 Merge branch 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6
Conflicts:
	drivers/net/wireless/rtlwifi/efuse.c
	drivers/net/wireless/rtlwifi/rtl8192c/fw_common.c
	net/bluetooth/mgmt.c
2011-04-07 16:45:40 -04:00
Jussi Kivilinna fbd5d17b8e zd1211rw: rename CR* macros to ZD_CR*
With compat-wireless CR* macros in zd_usb.h conflict with CR macros in
include/asm-generic/termbits.h. So rename CR* macros to ZD_CR*.

Conversion was done with using sed and then 'over 80 character line'
checkpatch.pl warnings and comment indents were fixed.

Reported-by: Walter Goldens <goldenstranger@yahoo.com>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-07 15:34:13 -04:00
Jussi Kivilinna 023535732f zd1211rw: reset rx idle timer from tasklet
2.6.38 added WARN_ON(in_irq) in del_timer_sync that triggers on zd1211rw when
reseting rx idle timer in urb completion handler.

Move timer reseting to tasklet.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-04 15:22:12 -04:00
Jussi Kivilinna 2fc713b204 zd1211rw: remove URB_SHORT_NOT_OK flag in zd_usb_iowrite16v_async()
Patch removes the bogus flag introduced by upstream commit
eefdbec1ea. Old code had buffer length check
that new code tried to handle with URB_SHORT_NOT_OK flag. With USB debugging
enabled bogus flag caused usb_submit_urb fail.

Remove URB_SHORT_NOT_OK flag and add buffer length check to urb completion
handler.

Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=32092
Reported-by: Jonathan Callen <abcd@gentoo.org>
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-04-04 15:22:12 -04:00
Lucas De Marchi 25985edced Fix common misspellings
Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-31 11:26:23 -03:00
Linus Torvalds 00a2470546 Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (56 commits)
  route: Take the right src and dst addresses in ip_route_newports
  ipv4: Fix nexthop caching wrt. scoping.
  ipv4: Invalidate nexthop cache nh_saddr more correctly.
  net: fix pch_gbe section mismatch warning
  ipv4: fix fib metrics
  mlx4_en: Removing HW info from ethtool -i report.
  net_sched: fix THROTTLED/RUNNING race
  drivers/net/a2065.c: Convert release_resource to release_region/release_mem_region
  drivers/net/ariadne.c: Convert release_resource to release_region/release_mem_region
  bonding: fix rx_handler locking
  myri10ge: fix rmmod crash
  mlx4_en: updated driver version to 1.5.4.1
  mlx4_en: Using blue flame support
  mlx4_core: reserve UARs for userspace consumers
  mlx4_core: maintain available field in bitmap allocator
  mlx4: Add blue flame support for kernel consumers
  mlx4_en: Enabling new steering
  mlx4: Add support for promiscuous mode in the new steering model.
  mlx4: generalization of multicast steering.
  mlx4_en: Reporting HW revision in ethtool -i
  ...
2011-03-25 21:02:22 -07:00
Tõnu Samuel 9011cd250e zd1211rw: TrendNet TEW-509UB id added
Signed-off-by: Tõnu Samuel <tonu@jes.ee>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-03-21 15:17:13 -04:00
Linus Torvalds a44f99c7ef Merge branch 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6
* 'trivial' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild-2.6: (25 commits)
  video: change to new flag variable
  scsi: change to new flag variable
  rtc: change to new flag variable
  rapidio: change to new flag variable
  pps: change to new flag variable
  net: change to new flag variable
  misc: change to new flag variable
  message: change to new flag variable
  memstick: change to new flag variable
  isdn: change to new flag variable
  ieee802154: change to new flag variable
  ide: change to new flag variable
  hwmon: change to new flag variable
  dma: change to new flag variable
  char: change to new flag variable
  fs: change to new flag variable
  xtensa: change to new flag variable
  um: change to new flag variables
  s390: change to new flag variable
  mips: change to new flag variable
  ...

Fix up trivial conflict in drivers/hwmon/Makefile
2011-03-20 18:14:55 -07:00
matt mooney 5a8b7cdc74 net: change to new flag variable
Replace EXTRA_CFLAGS with ccflags-y.

Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Acked-by: Sjur Braendeland <sjur.brandeland@stericsson.com>
Acked-by: David S. Miller <davem@davemloft.net>
Acked-by: John W. Linville <linville@tuxdriver.com>
Signed-off-by: Michal Marek <mmarek@suse.cz>
2011-03-17 14:05:35 +01:00
Johannes Berg 7bb4568372 mac80211: make tx() operation return void
The return value of the tx operation is commonly
misused by drivers, leading to errors. All drivers
will drop frames if they fail to TX the frame, and
they must also properly manage the queues (if they
didn't, mac80211 would already warn).

Removing the ability for drivers to return a BUSY
value also allows significant cleanups of the TX
TX handling code in mac80211.

Note that this also fixes a bug in ath9k_htc, the
old "return -1" there was wrong.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Sedat Dilek <sedat.dilek@googlemail.com> [ath5k]
Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> [rt2x00]
Acked-by: Larry Finger <Larry.Finger@lwfinger.net> [b43, rtl8187, rtlwifi]
Acked-by: Luciano Coelho <coelho@ti.com> [wl12xx]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-25 15:32:34 -05:00
Jussi Kivilinna 91f71fa5da zd1211rw: add unlikely to ZD_ASSERT
Case assert is violated should be quite unlikely.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14 15:51:21 -05:00
Jussi Kivilinna 8662b2518f zd1211rw: move async iowrite16v up to callers
Writing beacon to device happen through multiple write command calls.
zd_usb_iowrite16v uses synchronous urb call and with multiple write
commands in row causes high CPU usage.

Make asynchronous zd_usb_iowrite16v_async available outside zd_usb.c
and use where possible.

This lower CPU usage from ~10% to ~2% on Intel Atom when running
AP-mode with 100 TU beacon interval.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14 15:51:21 -05:00
Jussi Kivilinna eefdbec1ea zd1211rw: use async urb for write command
Writing beacon to device happen through multiple write command calls.
zd_usb_iowrite16v uses synchronous urb call and with multiple write
commands in row causes high CPU usage.

This patch makes zd_usb_iowrite16v use asynchronous urb submit within
zd_usb.c. zd_usb_iowrite16v_async_start is used to initiate writing
multiple commands to device using zd_usb_iowrite16v_async. Each URB
is delayed and submitted to device by next zd_usb_iowrite16v_async
call or by call to zd_usb_iowrite16v_async_end. URBs submitted by
zd_usb_iowrite16v_async have URB_NO_INTERRUPT set and last URB
send by zd_usb_iowrite16v_async_end does not. This lower CPU
usage when doing writes that require multiple URBs.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14 15:51:21 -05:00
Jussi Kivilinna 37939810b9 zd1211rw: correct use of usb_bulk_msg on interrupt endpoints
zd1211rw is using usb_bulk_msg() with usb_sndbulkpipe() on interrupt endpoint.
However usb_bulk_msg() internally corrects this and makes interrupt URB.

It's better to change usb_bulk_msgs in zd1211rw to usb_interrupt_msg for less
confusion.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-14 15:51:21 -05:00
Jussi Kivilinna 24d24c627c zd1211rw: add useful debug output
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:51 -05:00
Jussi Kivilinna ab419e9bda zd1211rw: enable NL80211_IFTYPE_AP
It should be safe to enable AP-mode now.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:51 -05:00
Jussi Kivilinna 1f6cccccea zd1211rw: reset rx urbs after idle period of 30 seconds
RX appears to freeze while idle. Resetting rx-urbs appears to be enough to fix
this. Do reset 30 seconds after last rx.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:51 -05:00
Jussi Kivilinna 3985a46543 zd1211rw: reset device when CR_BCN_FIFO_SEMAPHORE freezes in beacon setup
When driver fails to acquire device semaphore lock, device usually
freezes soon afterwards. So failing to acquire lock indicates us that
not everything is going right in device/fw. So reset device when
this happens.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:51 -05:00
Jussi Kivilinna a0fd751f09 zd1211rw: add TX watchdog and device resetting
When doing transfers at high speed for long time, tx queue can freeze. So add
tx watchdog. TX-watchdog checks for locked tx-urbs and reset hardware when
such is detected. Merely unlinking urb was not enough, device have to be
reseted. Hw settings are restored so that any open link will stay on after
reset.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:51 -05:00
Jussi Kivilinna 212e1a5b9d zd1211rw: collect driver settings and add function to restore theim
We need HW hard reset later in patchset to reset device after TX-stall.
Collect all settings that we have set to driver for later reset and
add restore function.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Jussi Kivilinna 8f2d8f869a zd1211rw: lower hw command timeouts
Device command timeouts are set up very high (1 sec) and this causes
AP beacon to lock up for long for example. Checking timeouts on device
it's easy to see that 1 sec timeout is not needed, when device fails
to response longer timeout doesn't help:

[  473.074419] zd1211rw 1-1:1.0: print_times() Read times:
[  473.175163] zd1211rw 1-1:1.0: print_time()     0 - 10 msec: 1506
[  473.176429] zd1211rw 1-1:1.0: print_time()    11 - 50 msec: 0
[  473.177955] zd1211rw 1-1:1.0: print_time()   51 - 100 msec: 0
[  473.180703] zd1211rw 1-1:1.0: print_time()  101 - 250 msec: 0
[  473.182101] zd1211rw 1-1:1.0: print_time()  251 - 500 msec: 0
[  473.183221] zd1211rw 1-1:1.0: print_time() 500 - 1000 msec: 20
[  473.184381] zd1211rw 1-1:1.0: print_time() 1000 - ... msec: 18

Also vendor driver doesn't use this long timeout. Therefore change
timeout to 50msec.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Jussi Kivilinna 4a3b0874a4 zd1211rw: change interrupt URB buffer to DMA buffer
As might lower beacon update CPU usage.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Jussi Kivilinna 9bca0c3b54 zd1211rw: use stack and preallocated memory for small cmd-buffers
Use stack for allocing small < 64 byte arrays in zd_chip.c and preallocated
buffer in zd_usb.c. This might lower CPU usage for beacon setup.

v2:
 - Do not use stack buffers in zd_usb.c as they would be used for urb
   transfer_buffer.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Jussi Kivilinna 5127229292 zd1211rw: batch beacon config commands together
Beacon config function writes beacon to hw one write per byte. This is very
slow (usually taking more than 100ms to finish) and causes high CPU usage
when in AP-mode (kworker at ~50% on Intel Atom N270). By batching commands
together zd_mac_config_beacon() runtime can be lowered to 1/5th and lower
CPU usage to saner levels (<10% on Atom).

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Jussi Kivilinna 9be2325636 zd1211rw: add beacon watchdog and setting HW beacon more failsafe
When doing tx/rx at high packet rate (for example simply using ping -f),
device starts to fail to respond to control messages. On non-AP modes
this only causes problems for LED updating code but when we are running
in AP-mode we are writing new beacon to HW usually every 100ms. Now if
control message fails in HW beacon setup, device lock is kept locked
and beacon data partially written. This can and usually does cause:

 1. HW beacon setup fail now on, as driver cannot acquire device lock.
 2. Beacon-done interrupt stop working as device has incomplete beacon.

Therefore make zd_mac_config_beacon() always try to release device lock
and add beacon watchdog to restart beaconing when stall is detected.

Also fix zd_mac_config_beacon() try acquiring device lock for max 500ms,
as what old code appeared to be trying to do using loop and msleep(1).

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:50 -05:00
Jussi Kivilinna 4099e2f440 zd1211rw: implement beacon fetching and handling ieee80211_get_buffered_bc()
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna b91a515dbb zd1211rw: let zd_set_beacon_interval() set dtim_period and add AP-beacon flag
Add support for AP-mode beacon. Also disable beacon when interface is set
down as otherwise hw will keep flooding NEXT_BCN interrupts.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna f773e409b9 zd1211rw: fix ack_pending in filter_ack causing tx-packet ordering problem on monitor
For reasons not very clear yet to me, filter_ack leaves matching tx-packet
pending with 'ack_pending'. This causes tx-packet to be passed back to upper
layer after next packet has been transfered and tx-packets might end up
coming come out of monitor interface in wrong order vs. rx.

Because of this when enable AP-mode, hostapd monitor interface would get
packets in wrong order causing problems in WPA association.

So don't use mac->ack_pending when in AP-mode.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna c2fadcb3b1 zd1211rw: support setting BSSID for AP mode
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna 5cf6cf819b zd1211rw: move set_rts_cts_work to bss_info_changed
As bss_info_changed may sleep, we can as well set RTS_CTS register right away.
Keep mac->short_preamble for later use (hw reset).

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna a6fb071bbf zd1211rw: move set_multicast_hash and set_rx_filter from workers to configure_filter
Workers not needed anymore since configure_filter may sleep. Keep
mac->multicast_hash for later use (hw reset).

Signed-off-by: Jussi Kivilinna <jussi.kivilina@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:49 -05:00
Jussi Kivilinna 88a1159a37 zd1211rw: fix beacon interval setup
Vendor driver uses CR_BNC_INTERVAL at various places, one is HW_EnableBeacon()
that combinies beacon interval with BSS-type flag and DTIM value in upper 16bit
of u32. The other one is HW_UpdateBcnInterval() that set_aw_pt_bi()
appears to be based on. HW_UpdateBcnInterval() takes interval argument as u16
and uses that for calculations, set_aw_pt_bi() uses u32 value that has flags
and dtim in upper part. This clearly seems wrong. Also HW_UpdateBcnInterval()
updates only lower 16bit part of CR_BNC_INTERVAL. So make set_aw_pt_bi() do
calculations on only lower u16 part of s->beacon_interval.

Also set 32bit beacon interval register before reading values from device,
as HW_EnableBeacon() on vendor driver does. This is required to make beacon
work on AP-mode, simply reading and then writing updated values is not enough
at least with zd1211b.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:48 -05:00
Jussi Kivilinna 8b17f75ced zd1211rw: add locking for mac->process_intr
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:48 -05:00
Jussi Kivilinna d741900d40 zd1211rw: cancel process_intr work on zd_chip_disable_int()
OOPS if worker is running and disconnect() is called (triggered
by unpluging device). Much harder to trigger at this stage but
later when we have AP beacon work in process_intr it happens very
easy.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:48 -05:00
Jussi Kivilinna 78fc800f06 zd1211rw: use urb anchors for tx and fix tx-queue disabling
When stress testing AP-mode I hit OOPS when unpluging or rmmodding
driver.

It appears that when tx-queue is disabled, tx-urbs might be left pending.
These can cause ehci to call non-existing tx_urb_complete() (after rmmod)
or uninitialized/reseted private structure (after disconnect()). Add skb
queue for submitted packets and unlink pending urbs on zd_usb_disable_tx().

Part of the problem seems to be usb->free_urb_list that isn't always
working as it should, causing machine freeze when trying to free the list
in zd_usb_disable_tx(). Caching free urbs isn't what other drivers seem
to be doing (usbnet for example) so strip free_usb_list.

Patch makes tx-urb handling saner with use of urb anchors.

Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2011-02-04 16:29:48 -05:00
Linus Torvalds 23d69b09b7 Merge branch 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq
* 'for-2.6.38' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (33 commits)
  usb: don't use flush_scheduled_work()
  speedtch: don't abuse struct delayed_work
  media/video: don't use flush_scheduled_work()
  media/video: explicitly flush request_module work
  ioc4: use static work_struct for ioc4_load_modules()
  init: don't call flush_scheduled_work() from do_initcalls()
  s390: don't use flush_scheduled_work()
  rtc: don't use flush_scheduled_work()
  mmc: update workqueue usages
  mfd: update workqueue usages
  dvb: don't use flush_scheduled_work()
  leds-wm8350: don't use flush_scheduled_work()
  mISDN: don't use flush_scheduled_work()
  macintosh/ams: don't use flush_scheduled_work()
  vmwgfx: don't use flush_scheduled_work()
  tpm: don't use flush_scheduled_work()
  sonypi: don't use flush_scheduled_work()
  hvsi: don't use flush_scheduled_work()
  xen: don't use flush_scheduled_work()
  gdrom: don't use flush_scheduled_work()
  ...

Fixed up trivial conflict in drivers/media/video/bt8xx/bttv-input.c
as per Tejun.
2011-01-07 16:58:04 -08:00
Tejun Heo afe2c511fb workqueue: convert cancel_rearming_delayed_work[queue]() users to cancel_delayed_work_sync()
cancel_rearming_delayed_work[queue]() has been superceded by
cancel_delayed_work_sync() quite some time ago.  Convert all the
in-kernel users.  The conversions are completely equivalent and
trivial.

Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: "David S. Miller" <davem@davemloft.net>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Cc: Jeff Garzik <jgarzik@pobox.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: netdev@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "J. Bruce Fields" <bfields@fieldses.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Alex Elder <aelder@sgi.com>
Cc: xfs-masters@oss.sgi.com
Cc: Christoph Lameter <cl@linux-foundation.org>
Cc: Pekka Enberg <penberg@cs.helsinki.fi>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: netfilter-devel@vger.kernel.org
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: linux-nfs@vger.kernel.org
2010-12-15 10:56:11 +01:00
David S. Miller 77148625e1 Merge branch 'for-davem' of git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-next-2.6 2010-11-29 11:19:09 -08:00
Joe Perches 47c0531432 zd1211rw: document need for kmalloc cast
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
2010-11-28 17:26:24 -08:00
Joe Perches 7253965a1c zd1211rw: Use const
Mark arrays const that are unmodified after initializations.

   text	   data	    bss	    dec	    hex	filename
  19291	     56	   4136	  23483	   5bbb	drivers/net/wireless/zd1211rw/zd_chip.o.old
  19291	     56	   4136	  23483	   5bbb	drivers/net/wireless/zd1211rw/zd_chip.o.new

Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
2010-11-22 15:58:54 -05:00