More packet statistics are now calculated and visible to the user via
ethtool:
- RX packet errors statistics.
- TX/RX drops are now calculated.
- TX multicast and broadcast statistics.
- RX/TX per priority bytes statistics.
- RX/TX no vlan packets and bytes statistics.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Flow control per priority and Global pause counters are now visible via
ethtool. The counters shows statistics regarding pauses in the device.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This will allow parallel access to the statistics bitmap.
A pre-step for adding PFC counters, where the statistics bitmap
can be dynamically changed when modifying the PFC setting.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver uses a bitmask to indicate which statistics should be
displayed to the user in ethtool. The bitmask is u64, therefore we are
limited for a selective view of up to 64 statistics. Extend the bitmap
in order to show more than 64 statistics.
In addition, add packet statistics to the ethtool display for PF.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The statistics bitmap belongs to the Ethernet driver, move it there.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add mlx4_stats.h file and move there all statistics structs and marcos.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Two counters (rx_chksum_complete and tx_chksum_offload) are not displayed
under SRIOV for the PF via ethtool because their bit mask is off, fix that.
Fixes: f8c6455bb ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Fixes: 9fab426de ('mlx4: add a new xmit_more counter')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver's clock is implemented using a timecounter, and so with
this patch the driver is ready for the year 2038.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
To allow drivers to handle the features check for multiple tags,
move the check to ndo_features_check().
As no drivers currently handle multiple tagged TSO, introduce
dflt_features_check() and call it if the driver does not have
ndo_features_check().
Signed-off-by: Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
We occasionally see in procedure mlx4_GEN_EQE that the driver tries
to grab an uninitialized mutex.
This can occur in only one of two ways:
1. We are trying to generate an async event on an uninitialized slave.
2. We are trying to generate an async event on an illegal slave number
( < 0 or > persist->num_vfs) or an inactive slave.
To deal with #1: move the mutex initialization from specific slave init
sequence in procedure mlx_master_do_cmd to mlx4_multi_func_init() (so that
the mutex is always initialized for all slaves).
To deal with #2: check in procedure mlx4_GEN_EQE that the slave number
provided is in the proper range and that the slave is active.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Netdevice registration should be performed a the end of the driver
initialization flow. If we don't do that, after calling register_netdevice,
device callbacks may be issued by higher layers of the stack before
final configuration of the device is done.
For example (VXLAN configuration race), mlx4_SET_PORT_VXLAN was issued
after the register_netdev command. System network scripts may configure
the interface (UP) right after the registration, which also attach
unicast VXLAN steering rule, before mlx4_SET_PORT_VXLAN was called,
causing the firmware to fail the rule attachment.
Fixes: 837052d0cc ("net/mlx4_en: Add netdev support for TCP/IP offloads of vxlan tunneling")
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
net/core/sysctl_net_core.c
net/ipv4/inet_diag.c
The be_main.c conflict resolution was really tricky. The conflict
hunks generated by GIT were very unhelpful, to say the least. It
split functions in half and moved them around, when the real actual
conflict only existed solely inside of one function, that being
be_map_pci_bars().
So instead, to resolve this, I checked out be_main.c from the top
of net-next, then I applied the be_main.c changes from 'net' since
the last time I merged. And this worked beautifully.
The inet_diag.c and sysctl_net_core.c conflicts were simple
overlapping changes, and were easily to resolve.
Signed-off-by: David S. Miller <davem@davemloft.net>
Port statistics bitmap will now be initialized at port init. Even before
starting the port, statistics are visible to the user and must be properly masked.
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NUM_PORT_STATS was 9 instead of 10, which caused off-by-one bug when
displaying the statistics starting from tx_chksum_offload in ethtool.
Fixes: f8c6455bb0 ('net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Hadar Hen Zion <hadarh@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ndo_set_tx_maxrate support.
To support per tx queue maxrate limit, we use the update-qp firmware
command to do run-time rate setting for the qp that serves this tx ring.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the low-level device commands and definitions used for QP max-rate limiting.
This is done through the following elements:
- read rate-limit device caps in QUERY_DEV_CAP: number of different
rates and the min/max rates in Kbs/Mbs/Gbs units
- enhance the QP context struct to contain rate limit units and value
- allow to do run time rate-limit setting to QPs through the
update-qp firmware command
- QP rate-limiting is disallowed for VFs
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@r@
type T;
identifier f;
@@
static T f (...) { ... }
@@
identifier r.f;
declarer name EXPORT_SYMBOL;
@@
-EXPORT_SYMBOL(f);
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
To test a checkpatch spelling patch, I ran codespell against
drivers/net/ethernet/.
$ git ls-files drivers/net/ethernet/ | \
while read file ; do \
codespell -w $file; \
done
I removed a false positive in e1000_hw.h
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the IEEE DCB handlers for set/get QCN parameters and
statistics reading per TC.
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add device capability, firmware command opcode and etc prior elements
needed for QCN suppprt. Disable SRIOV VF view/access for QCN is disabled.
While here, remove a redundant offset definition into the
QUERY_DEV_CAP mailbox.
Signed-off-by: Shani Michaeli <shanim@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Packets which are sent from the selftest (ethtool) flow,
should not be passed to GRO stack but rather dropped by
the driver after validation. To achieve that, we disable
GRO for the duration of the selftest.
Fixes: dd65beac48 ("net/mlx4_en: Extend usage of napi_gro_frags")
Reported-by: Carol Soto <clsoto@linux.vnet.ibm.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The bit mask for currently supported driver features (MLX4_UPDATE_QP_SUPPORTED_ATTRS)
of the update-qp command was defined twice (using enum value and pre-processor
define directive) and wrong.
The return value of the call to mlx4_update_qp() from within the SRIOV
resource-tracker was wrongly voided down.
Fix both issues.
issue: none
Fixes: 09e05c3f78 ('net/mlx4: Set vlan stripping policy by the right command')
Fixes: ce8d9e0d67 ('net/mlx4_core: Add UPDATE_QP SRIOV wrapper support')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current code failed to configure the page size for architectures with page
size different than 4K - PPC for example.
Signed-off-by: Carol L Soto <clsoto@us.ibm.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The vunmap() function performs also input parameter validation.
Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
drivers/net/vxlan.c
drivers/vhost/net.c
include/linux/if_vlan.h
net/core/dev.c
The net/core/dev.c conflict was the overlap of one commit marking an
existing function static whilst another was adding a new function.
In the include/linux/if_vlan.h case, the type used for a local
variable was changed in 'net', whereas the function got rewritten
to fix a stacked vlan bug in 'net-next'.
In drivers/vhost/net.c, Al Viro's iov_iter conversions in 'net-next'
overlapped with an endainness fix for VHOST 1.0 in 'net'.
In drivers/net/vxlan.c, vxlan_find_vni() added a 'flags' parameter
in 'net-next' whereas in 'net' there was a bug fix to pass in the
correct network namespace pointer in calls to this function.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch improves memory utilization and therefore the packets rate
for special MTU's. Instead of setting the frag_stride to the maximal
hard coded frag_size, use the actual frag_size that is set according to
the MTU, when setting the stride of the last frag.
So, for example, for MTU 1600, where the frag_size of the 2nd frag is
86, the frag_size is set to 128 instead of 4096. See below:
Before:
frag:0 - size:1536 prefix:0 stride:1536
frag:1 - size:86 prefix:1536 stride:4096
frag 0 allocator: - size:32768 frags:21
frag 1 allocator: - size:32768 frags:8
After:
frag:0 - size:1536 prefix:0 stride:1536
frag:1 - size:86 prefix:1536 stride:128
frag 0 allocator: - size:32768 frags:21
frag 1 allocator: - size:32768 frags:256
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
After Initialization of page_alloc, print actual allocated page
size and number of frags it contains. prints is done only when drv
message level is set on the interface.
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Align the IDs in the code with the modinfo, lspci -n, etc tools outputs.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We do support cache line sizes of 32 and 64 bytes without activating the
CQE stride feature. Fix a misleading print saying that these cache line
sizes aren't supported.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add Initialization to struct config_dev before filling and using it.
Fix to warning:
warning: config_dev.rx_checksum_val may be used uninitialized in this function
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
a) Previously, mlx4_mr_rereg_write filled the MPT's start
and length with the old MPT's values.
Fixing the initialization to take the new start and length.
b) In addition access flags in mpt_status were initialized instead of
status due to bad boolean operation. Fixing the operation.
c) Initialization of pd_slave caused a protection error.
Fix - removing this initialization.
d) In resource_tracker.c: Fixing vf encoding to be one-based.
Fixes: e630664c ('mlx4_core: Add helper functions to support MR re-registration')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Capture NETDEV events generated by the bonding driver and based on that
make decisions of how to configure port aggregation in the mlx4 core driver.
This includes setting the V2P port table and re-creating the interested
interfaces in bonded/non-bonded mode.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Supply interface functions to bond and unbond ports of a mlx4 internal
interfaces. Example for such an interface is the one registered by the
mlx4 IB driver under RoCE.
There are
1. Functions to go in/out to/from bonded mode
2. Function to remap virtual ports to physical ports
The bond_mutex prevents simultaneous access to data that keep status of
the device in bonded mode.
The upper mlx4 interface marks to the mlx4 core module that they
want to be subject for such bonding by setting the MLX4_INTFF_BONDING
flag. Interface which goes to/from bonded mode is re-created.
The mlx4 Ethernet driver does not set this flag when registering the
interface, the IB driver does.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implement the hardware interface required for port aggregation.
1. Disable RX port check on receive - don't perform a validity check
that matches to QP's port and the port where the packet is received.
2. Virtual to physical port remap - configure virtual to physical port
mapping. Port remap capability for virtual functions.
Signed-off-by: Moni Shoua <monis@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Commit de966c5928 (net/mlx4_core: Support more than 64 VFs) was meant to
allow up to 126 VFs. However, due to leaving MLX4_MFUNC_MAX too low, using
more than 80 VFs resulted in memory corruptions (and Oopses) when more than
80 VFs were requested. In addition, the number of slaves was left too high.
This commit fixes these issues.
Fixes: de966c5928 ("net/mlx4_core: Support more than 64 VFs")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware might change the hca core clock frequency after the driver
issues the INIT_PORT command. Therefore we need to query the new
value again and save in to the cached dev caps.
Fixes: ddd8a6c1 ('net/mlx4_core: Read HCA frequency and map internal clock')
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are dumping device capabilities which are supported both by the
firmware and the driver. Align the array that holds the capability
strings with this practice.
Reported-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a memory corruption at mlx4_MAD_IFC_wrapper.
A table of size dev->caps.pkey_table_len[port]*sizeof(*table)
was allocated, but get_full_pkey_table() assumes that the number
of entries in the table is a multiplication of 32 (which isn't always
correct).
Fixes: 0a9a018 ('mlx4: MAD_IFC paravirtualization')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use cmd->autoneg as a user hint to decide what to set in ethtool set settings callback.
When cmd->autoneg == AUTONEG_ENABLE set according to ethtool->advertise otherwise,
set according to ethtool->speed.
Usage:
- ethtool -s eth<x> speed 56000 autoneg off
- ethtool -s eth<x> advertise 0x800000 autoneg on
While we're here:
- Move proto_admin masking outcome check to be adjacent to the operation.
- Move en_warn("port reset..") print to "port reset" block.
Fixes: 312df74 ("net/mlx4_en: mlx4_en_set_settings() always fails when autoneg is set")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx4_bf_alloc had an unnecessary/duplicate code line. Did no harm,
but not good practice.
Reported by the Mellanox Beijing team.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Struct mlx4_vhcr was implicitly padded by the gcc compiler on 64-bit
architectures.
This commit makes that padding explicit, to prevent issues with
changing compilers and with incompatibilities between 32-bit architecture
implicit padding and 64-bit architecture implicit padding.
This structure is used in virtualization for communication between
the Host and its Guests. The explicit padding allows 64-bit Hosts
(old and new) to continue to interoperate with 64-bit Guests (old and new).
However, without this fix, 64-bit Hosts could not interoperate with 32-bit
Guests (since these did not insert the padding dword). With this fix,
32-bit Guests will be able to interoperate with 64-bit Hosts (since
the structure offsets will be identical on both).
Reported-by: Alexander Schmidt <alexs@linux.vnet.ibm.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The driver incorrectly assigned an out-mailbox to this command,
and used an opcode modifier = 0, which is a reserved value (it
should use opcode modifier = 1).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The firmware spec states that the timeout for all commands should be 60 seconds.
In the past, the spec indicated that there were several classes of timeout
(short, medium, and long). The driver has these different timeout classes.
We leave the class differentiation in the driver as-is (to protect against any
future spec changes), but set the timeout for all classes to be 60 seconds.
In addition, we fix a few commands which had hard-coded numeric timeouts specified.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Structs allocated for the resource tracker must be freed in
the error flow.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The reserved lKey is different for each VF.
A base lkey value is returned in QUERY_DEV_CAP at offset 0x98.
The reserved L_key value for a VF is:
VF_lkey = base_lkey + (VF_number << 8).
This VF L_key value should be returned in QUERY_FUNC_CAP
(opcode-modifier = 0) at offset 0x48.
To indicate that the lkey value at offset 0x48 is valid, the Hypervisor
sets a flag bit in dword 0x0, offset 27 in the QUERY_FUNC_CAP wrapper
function.
When the VF calls QUERY_FUNC_CAP, it should check if this flag bit is set.
If it is set, the VF should take the reserved lkey value at offset 0x48.
If the bit is not set, the VF should not use a reserved lkey
(i.e., should set its reserved lkey value to 0).
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
If the firmware can detect a bad cable, allow it to generate an
event, and print the problem in the log.
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
When SRIOV commands are executed over the comm-channel and get
a fatal error (e.g. timeout, closing command failure) the VF enters
into error state and reset flow is activated.
To be able to recognize whether the failure was on a closing command, the
operational code for the given VHCR command is used. Once the device entered
into an error state we prevent redundant error messages from being printed.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
In SRIOV, both the PF and the VF may attempt device recovery whenever they
assume that the device is not functioning. When the PF driver resets the
device, the VF should detect this and attempt to reinitialize itself.
The VF must be able to reset itself under all circumstances, even
if the PF is not responsive.
The VF shall reset itself in the following cases:
1. Commands are not processed within reasonable time over the communication channel.
This is done considering device state and the correct return code based on
the command as was done in the native mode, done in the next patch.
2. The VF driver receives an internal error event reported by the PF on the
communication channel. This occurs when the PF driver resets the device or
when VF is out of sync with the PF.
Add 'VF reset' capability, which allows the VF to reinitialize itself even when the
PF is not responsive.
As PF and VF may run their reset flow simulantanisly, there are several cases
that are handled:
- Prevent freeing VF resources upon FLR, when PF is in its unloading stage.
- Prevent PF getting VF commands before it has finished initializing its resources.
- Upon VF startup, check that comm-channel is online before sending
commands to the PF and getting timed-out.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix AER callbacks to work properly, it includes:
- Refractoring AER to be aligned with Reset flow support.
- Sync with concurrent catas flow.
In addition, fix the shutdown PCI callback to sync with
concurrent catas flow.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We need to manage interface state to sync between reset flow and some other
relative cases such as remove_one. This has to be done to prevent certain
races. For example in case software stack is down as a result of unload call,
the remove_one should skip the unload phase.
Implement the remove_one case, handling AER and other cases comes next.
The interface can be up/down, upon remove_one, the state will include an extra
bit indicating that the device is cleaned-up, forcing other tasks to finish
before the final cleanup.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We activate reset flow upon command fatal errors, when the device enters an
erroneous state, and must be reset.
The cases below are assumed to be fatal: FW command timed-out, an error from FW
on closing commands, pci is offline when posting/pending a command.
In those cases we place the device into an error state: chip is reset, pending
commands are awakened and completed immediately. Subsequent commands will
return immediately.
The return code in the above cases will depend on the command. Commands which
free and close resources will return success (because the chip was reset, so
callers may safely free their kernel resources). Other commands will return -EIO.
Since the device's state was marked as error, the catas poller will
detect this and restart the device's software stack (as is done when a FW
internal error is directly detected). The device state is protected by a
persistent mutex lives on its mlx4_dev, as such no need any more for the
hcr_mutex which is removed.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This includes:
- resetting the chip when a fatal error is detected (the current code
does not do this).
- exposing the ability to enter error state from outside the catas code
by calling its functionality. (E.g. FW Command timeout, AER error).
- managing a persistent device state. This is needed to sync between
reset flow cases.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Using a WQ per device instead of a single global WQ, this allows
independent reset handling per device even when SRIOV is used.
This comes as a pre-patch for supporting chip reset
for both native and SRIOV.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When an HCA enters an internal error state, this is detected by the driver.
The driver then should reset the HCA and restart the software stack.
Keep ports information and some SRIOV configuration in a persistent area
to have it valid across reset.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Maintain a persistent memory that should survive reset flow/PCI error.
This comes as a preparation for coming series to support above flows.
Signed-off-by: Yishai Hadas <yishaih@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Except for VXLAN steering rules, all offloads should work as they were
under plain DMFS mode. Fix that by enabling all the offloads under
DMFS-A0 mode, except for VXLAN steering rules.
Fixes: d57febe1a4 "net/mlx4: Add A0 hybrid steering"
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
The mlx5 driver passes a string pointer in through a 'u64' variable,
which on 32-bit machines causes a build warning:
drivers/net/ethernet/mellanox/mlx5/core/debugfs.c: In function 'qp_read_field':
drivers/net/ethernet/mellanox/mlx5/core/debugfs.c:303:11: warning: cast from pointer to integer of different size [-Wpointer-to-int-cast]
The code is in fact safe, so we can shut up the warning by adding
extra type casts.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This driver uses the function, clocksource_khz2mult, and so it really must
include clocksource.h.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We shouldn't call UNMAP_FA here, this is done in mlx4_load_one.
If mlx4_query_func fails, we need to invoke CLOSE_HCA for both
native and master.
Fixes: a0eacca948 ('net/mlx4_core: Refactor mlx4_load_one')
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, mlx4_mt_rereg_write filled the MPT's entity_size with the
old MTT's page shift, which could result in using an incorrect offset.
Fix the initialization to be after we calculate the new MTT offset.
In addition, assign mtt order to -1 after calling mlx4_mtt_cleanup. This
is necessary in order to mark the MTT as invalid and avoid freeing it later.
Fixes: e630664 ('mlx4_core: Add helper functions to support MR re-registration')
Signed-off-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current timecounter implementation will drop a variable amount
of resolution, depending on the magnitude of the time delta. In
other words, reading the clock too often or too close to a time
stamp conversion will introduce errors into the time values. This
patch fixes the issue by introducing a fractional nanosecond field
that accumulates the low order bits.
Reported-by: Janusz Użycki <j.uzycki@elproma.com.pl>
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch changes the driver to use the new and improved method
for adjusting the offset of a timecounter.
Compile tested only.
Signed-off-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
GSO isn't the only offload feature with restrictions that
potentially can't be expressed with the current features mechanism.
Checksum is another although it's a general issue that could in
theory apply to anything. Even if it may be possible to
implement these restrictions in other ways, it can result in
duplicate code or inefficient per-packet behavior.
This generalizes ndo_gso_check so that drivers can remove any
features that don't make sense for a given packet, similar to
netif_skb_features(). It also converts existing driver
restrictions to the new format, completing the work that was
done to support tunnel protocols since the issues apply to
checksums as well.
By actually removing features from the set that are used to do
offloading, it solves another problem with the existing
interface. In these cases, GSO would run with the original set
of features and not do anything because it appears that
segmentation is not required.
CC: Tom Herbert <therbert@google.com>
CC: Joe Stringer <joestringer@nicira.com>
CC: Eric Dumazet <edumazet@google.com>
CC: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: Jesse Gross <jesse@nicira.com>
Acked-by: Tom Herbert <therbert@google.com>
Fixes: 04ffcb255f ("net: Add ndo_gso_check")
Tested-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
iowrite32() will byteswap it's argument on big endian archs.
iowrite32be() will byteswap on little endian archs.
Since we don't want to do this unnecessary byteswap on the fast path,
doorbell is stored in the NIC's native endianness. Using the right
iowrite() according to the arch endianness.
CC: Wei Yang <weiyang@linux.vnet.ibm.com>
CC: David Laight <david.laight@aculab.com>
Fixes: 6a4e812 ("net/mlx4_en: Avoid calling bswap in tx fast path")
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- On-demand paging support in core midlayer and mlx5 driver. This lets
userspace create non-pinned memory regions and have the adapter HW
trigger page faults.
- iSER and IPoIB updates and fixes.
- Low-level HW driver updates for cxgb4, mlx4 and ocrdma.
- Other miscellaneous fixes.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=MCO9
-----END PGP SIGNATURE-----
Merge tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband
Pull infiniband updates from Roland Dreier:
"Main batch of InfiniBand/RDMA changes for 3.19:
- On-demand paging support in core midlayer and mlx5 driver. This
lets userspace create non-pinned memory regions and have the
adapter HW trigger page faults.
- iSER and IPoIB updates and fixes.
- Low-level HW driver updates for cxgb4, mlx4 and ocrdma.
- Other miscellaneous fixes"
* tag 'rdma-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband: (56 commits)
IB/mlx5: Implement on demand paging by adding support for MMU notifiers
IB/mlx5: Add support for RDMA read/write responder page faults
IB/mlx5: Handle page faults
IB/mlx5: Page faults handling infrastructure
IB/mlx5: Add mlx5_ib_update_mtt to update page tables after creation
IB/mlx5: Changes in memory region creation to support on-demand paging
IB/mlx5: Implement the ODP capability query verb
mlx5_core: Add support for page faults events and low level handling
mlx5_core: Re-add MLX5_DEV_CAP_FLAG_ON_DMND_PG flag
IB/srp: Allow newline separator for connection string
IB/core: Implement support for MMU notifiers regarding on demand paging regions
IB/core: Add support for on demand paging regions
IB/core: Add flags for on demand paging support
IB/core: Add support for extended query device caps
IB/mlx5: Add function to read WQE from user-space
IB/core: Add umem function to read data from user-space
IB/core: Replace ib_umem's offset field with a full address
IB/mlx5: Enhance UMR support to allow partial page table update
IB/mlx5: Remove per-MR pas and dma pointers
RDMA/ocrdma: Always resolve destination mac from GRH for UD QPs
...
This commit contains 2 fixes for the 128B CQE/EQE stride feaure.
Wei found that mlx4_QUERY_HCA function marked the wrong capability
in flags (64B CQE/EQE), when CQE/EQE stride feature was enabled.
Also added small fix in initial CQE ownership bit assignment, when CQE
is size is not default 32B.
Fixes: 77507aa24 (net/mlx4: Enable CQE/EQE stride support)
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Signed-off-by: Ido Shamay <idos@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* Add a handler function pointer in the mlx5_core_qp struct for page
fault events. Handle page fault events by calling the handler
function, if not NULL.
* Add on-demand paging capability query command.
* Export command for resuming QPs after page faults.
* Add various constants related to paging support.
Signed-off-by: Sagi Grimberg <sagig@mellanox.com>
Signed-off-by: Shachar Raindel <raindel@mellanox.com>
Signed-off-by: Haggai Eran <haggaie@mellanox.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
Move check for DPDP out of the loop to make the code more readable.
Signed-off-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: Roland Dreier <roland@purestorage.com>
To support asymmetric EQ allocations, we should query the device
capabilities prior to enabling SRIOV. As a side effect of adding that,
we are dumping the PF device capabilities twice. Avoid that by moving
the printing into a helper function which is called once.
Fixes: 7ae0e400cd ('net/mlx4_core: Flexible (asymmetric) allocation of
EQs and MSI-X vectors for PF/VFs')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The current mlx4_load_one has a memory leak as it always allocates
dev_cap, but frees it only on error.
In addition, even if VFs exist when mlx4_load_one is called,
we still need to notify probed VFs that we're loading (by
incrementing pf_loading).
Fixes: a0eacca948 ('net/mlx4_core: Refactor mlx4_load_one')
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the required firmware commands for A0 steering and a way to enable
that. The firmware support focuses on INIT_HCA, QUERY_HCA, QUERY_PORT,
QUERY_DEV_CAP and QUERY_FUNC_CAP commands. Those commands are used
to configure and query the device.
The different A0 DMFS (steering) modes are:
Static - optimized performance, but flow steering rules are
limited. This mode should be choosed explicitly by the user
in order to be used.
Dynamic - this mode should be explicitly choosed by the user.
In this mode, the FW works in optimized steering mode as long as
it can and afterwards automatically drops to classic (full) DMFS.
Disable - this mode should be explicitly choosed by the user.
The user instructs the system not to use optimized steering, even if
the FW supports Dynamic A0 DMFS (and thus will be able to use optimized
steering in Default A0 DMFS mode).
Default - this mode is implicitly choosed. In this mode, if the FW
supports Dynamic A0 DMFS, it'll work in this mode. Otherwise, it'll
work at Disable A0 DMFS mode.
Under SRIOV configuration, when the A0 steering mode is enabled,
older guest VF drivers who aren't using the RX QP allocation flag
(MLX4_RESERVE_A0_QP) will get a QP from the general range and
fail when attempting to register a steering rule. To avoid that,
the PF context behaviour is changed once on A0 static mode, to
require support for the allocation flag in VF drivers too.
In order to enable A0 steering, we use log_num_mgm_entry_size param.
If the value of the parameter is not positive, we treat the absolute
value of log_num_mgm_entry_size as a bit field. Setting bit 2 of this
bit field enables static A0 steering.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently QUERY_PORT is done as a part of QUERY_DEV_CAP firmware command.
Since we would like to use it without querying all device capabilities,
extract this part to be a function of its own.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When a given flow steering rule is invalid in respect to the current
steering configuration, print the correct error message to the system log.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
A0 hybrid steering is a form of high performance flow steering.
By using this mode, mlx4 cards use a fast limited table based steering,
in order to enable fast steering of unicast packets to a QP.
In order to implement A0 hybrid steering we allocate resources
from different zones:
(1) General range
(2) Special MAC-assigned QPs [RSS, Raw-Ethernet] each has its own region.
When we create a rss QP or a raw ethernet (A0 steerable and BF ready) QP,
we try hard to allocate the QP from range (2). Otherwise, we try hard not
to allocate from this range. However, when the system is pushed to its
limits and one needs every resource, the allocator uses every region it can.
Meaning, when we run out of raw-eth qps, the allocator allocates from the
general range (and the special-A0 area is no longer active). If we run out
of RSS qps, the mechanism tries to allocate from the raw-eth QP zone. If that
is also exhausted, the allocator will allocate from the general range
(and the A0 region is no longer active).
Note that if a raw-eth qp is allocated from the general range, it attempts
to allocate the range such that bits 6 and 7 (blueflame bits) in the
QP number are not set.
When the feature is used in SRIOV, the VF has to notify the PF what
kind of QP attributes it needs. In order to do that, along with the
"Eth QP blueflame" bit, we reserve a new "A0 steerable QP". According
to the combination of these bits, the PF tries to allocate a suitable QP.
In order to maintain backward compatibility (with older PFs), the PF
notifies which QP attributes it supports via QUERY_FUNC_CAP command.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The zone allocator is a mechanism which manages a few mlx4_bitmaps.
When allocating a resource, the user indicates the desired zone of
which this resource will be allocated from. If possible, the resource
will be allocated from this zone. Otherwise, the resource will be
allocated from a less-than, equal-to, higher-than priority zone,
according to the desired zone's properties with that respective
allocation order.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The number of reserved QPs is affected both from the firmware and
from the driver's requirements. This patch adds a check that
validates that this number is indeed feasable.
Signed-off-by: Dotan Barak <dotanb@dev.mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When using BF (Blue-Flame), the QPN overrides the VLAN, CV, and SV fields
in the WQE. Thus, BF may only be used for QPNs with bits 6,7 unset.
The current Ethernet driver code reserves a Tx QP range with 256b alignment.
This is wrong because if there are more than 64 Tx QPs in use,
QPNs >= base + 65 will have bits 6/7 set.
This problem is not specific for the Ethernet driver, any entity that
tries to reserve more than 64 BF-enabled QPs should fail. Also, using
ranges is not necessary here and is wasteful.
The new mechanism introduced here will support reservation for
"Eth QPs eligible for BF" for all drivers: bare-metal, multi-PF, and VFs
(when hypervisors support WC in VMs). The flow we use is:
1. In mlx4_en, allocate Tx QPs one by one instead of a range allocation,
and request "BF enabled QPs" if BF is supported for the function
2. In the ALLOC_RES FW command, change param1 to:
a. param1[23:0] - number of QPs
b. param1[31-24] - flags controlling QPs reservation
Bit 31 refers to Eth blueflame supported QPs. Those QPs must have
bits 6 and 7 unset in order to be used in Ethernet.
Bits 24-30 of the flags are currently reserved.
When a function tries to allocate a QP, it states the required attributes
for this QP. Those attributes are considered "best-effort". If an attribute,
such as Ethernet BF enabled QP, is a must-have attribute, the function has
to check that attribute is supported before trying to do the allocation.
In a lower layer of the code, mlx4_qp_reserve_range masks out the bits
which are unsupported. If SRIOV is used, the PF validates those attributes
and masks out unsupported attributes as well. In order to notify VFs which
attributes are supported, the VF uses QUERY_FUNC_CAP command. This command's
mailbox is filled by the PF, which notifies which QP allocation attributes
it supports.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.co.il>
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Previously, we've fired all our completion callbacks straight from our ISR.
Some of those callbacks were lightweight (for example, mlx4_en's and
IPoIB napi callbacks), but some of them did more work (for example,
the user-space RDMA stack uverbs' completion handler). Besides that,
doing more than the minimal work in ISR is generally considered wrong,
it could even lead to a hard lockup of the system. Since when a lot
of completion events are generated by the hardware, the loop over those
events could be so long, that we'll get into a hard lockup by the system
watchdog.
In order to avoid that, add a new way of invoking completion events
callbacks. In the interrupt itself, we add the CQs which receive completion
event to a per-EQ list and schedule a tasklet. In the tasklet context
we loop over all the CQs in the list and invoke the user callback.
Signed-off-by: Matan Barak <matanb@mellanox.com>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When VFs (guests in this context) issue the QUERY_DEV_CAP command, they
need not be told that host side virtualization features such as VST, FSM
(MAC anti-spoofing) and running > 80 VFs are supported by the device.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This was dropped by mistake for the napi_gro_frags flow, fix that.
Fixes: dd65beac48 ('net/mlx4_en: Extend usage of napi_gro_frags')
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ConnectX HW is capable of using one of the following hash functions:
Toeplitz and an XOR hash function. This patch extends the implementation
of the mlx4_en driver set/get_rxfh callbacks to support getting and
setting the RSS hash function used by the device.
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch extends the set/get_rxfh ethtool-options for getting or
setting the RSS hash function.
It modifies drivers implementation of set/get_rxfh accordingly.
This change also delegates the responsibility of checking whether a
modification to a certain RX flow hash parameter is supported to the
driver implementation of set_rxfh.
User-kernel API is done through the new hfunc bitmask field in the
ethtool_rxfh struct. A bit set in the hfunc field is corresponding to an
index in the new string-set ETH_SS_RSS_HASH_FUNCS.
Got approval from most of the relevant driver maintainers that their
driver is using Toeplitz, and for the few that didn't answered, also
assumed it is Toeplitz.
Cc: Tom Lendacky <thomas.lendacky@amd.com>
Cc: Ariel Elior <ariel.elior@qlogic.com>
Cc: Prashant Sreedharan <prashant@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Cc: Hariprasad S <hariprasad@chelsio.com>
Cc: Sathya Perla <sathya.perla@emulex.com>
Cc: Subbu Seetharaman <subbu.seetharaman@emulex.com>
Cc: Ajit Khaparde <ajit.khaparde@emulex.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Jesse Brandeburg <jesse.brandeburg@intel.com>
Cc: Bruce Allan <bruce.w.allan@intel.com>
Cc: Carolyn Wyborny <carolyn.wyborny@intel.com>
Cc: Don Skidmore <donald.c.skidmore@intel.com>
Cc: Greg Rose <gregory.v.rose@intel.com>
Cc: Matthew Vick <matthew.vick@intel.com>
Cc: John Ronciak <john.ronciak@intel.com>
Cc: Mitch Williams <mitch.a.williams@intel.com>
Cc: Amir Vadai <amirv@mellanox.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Shradha Shah <sshah@solarflare.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Eyal Perry <eyalpe@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add ConnectX-4LX to the list of supported devices as well as their virtual
functions.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The outbox should be cleared before executing the command.
Signed-off-by: Majd Dibbiny <majd@mellanox.com>
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Command queue descriptor page size is 4KB and not the page size used by the
kernel.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
mlx5 requires at least one interrupt vector for completions so fix the minvec
argument to pci_enable_msix_range() accordingly.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Call request module on mlx5_ib so it will be available for applications
requiring it, such as installers that require boot over IB.
Signed-off-by: Eli Cohen <eli@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
So this can be reused for identification of other "items" as well.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Reviewed-by: Thomas Graf <tgraf@suug.ch>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Andy Gospodarek <gospo@cumulusnetworks.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some VF drivers use the upper byte of "param1" (the qp count field)
in mlx4_qp_reserve_range() to pass flags which are used to optimize
the range allocation.
Under the current code, if any of these flags are set, the 32-bit
count field yields a count greater than 2^24, which is out of range,
and this VF fails.
As these flags represent a "best-effort" allocation hint anyway, they may
safely be ignored. Therefore, the PF driver may simply mask out the bits.
Fixes: c82e9aa0a8 "mlx4_core: resource tracking for HCA resources used by guests"
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Eran Ben Elisha