pcnet_cs,serial_cs:
add cis of PreMax ethernet pcmcia card,
and some Sierra Wireless serial card(AC555, AC7xx, AC8xx).
use PROD_ID for AC7xx, because MANF_ID of AC7xx and AC8xx are the same.
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Value of zero was used to disable the fairness mechanism. Though the code
(driver and FW) allowed changing the value at run time, it did not allow to do
that if the mechanism was disabled to begin with.
Fixed the FW to allow turning on and off the mechanism at run time. Fixed the
code to read the value from the chip at the right sequence.
Without this fix, if the initial value was set to zero, traffic could not run on
the interface.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs,serial_cs:
add cis of National Semicondoctor's lan&modem mulitifunction pcmcia card,
NE2K, tamarack ethernet card,
and some serial card(COMpad2, COMpad4).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix up -Wmissing-prototypes in compileable userspace code, mainly under
Documentation/.
Signed-off-by: Ladinu Chandrasinghe <ladinu.pub@gmail.com>
Signed-off-by: Trevor Keith <tsrk@tsrk.net>
Cc: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* 'drm-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6: (133 commits)
drm/vgaarb: add VGA arbitration support to the drm and kms.
drm/radeon: some r420s have a CP race with the DMA engine.
drm/radeon/r600/kms: rv670 is not DCE3
drm/radeon/kms: r420 idle after programming GA_ENHANCE
drm/radeon/kms: more fixes to rv770 suspend/resume path.
drm/radeon/kms: more alignment for rv770.c with r600.c
drm/radeon/kms: rv770 blit init called too late.
drm/radeon/kms: move around new init path code to avoid posting at init
drm/radeon/r600: fix some issues with suspend/resume.
drm/radeon/kms: disable VGA rendering engine before taking over VRAM
drm/radeon/kms: Move radeon_get_clock_info() call out of radeon_clocks_init().
drm/radeon/kms: add initial connector properties
drm/radeon/kms: Use surfaces for scanout / cursor byte swapping on big endian.
drm/radeon/kms: don't fail if we fail to init GPU acceleration
drm/r600/kms: fixup number of loops per blit calculation.
drm/radeon/kms: reprogram format in set base.
drm/radeon: avivo chips have no separate int bit for display
drm/radeon/r600: don't do interrupts
drm: fix _DRM_GEM addmap error message
drm: update crtc x/y when only fb changes
...
Fixed up trivial conflicts in firmware/Makefile due to network driver
(cxgb3) and drm (mga/r128/radeon) firmware being listed next to each
other.
pcnet_cs,serial_cs:
add cis of Linksys lan&modem mulitifunction pcmcia card
and some modem card(MT5634ZLX, RS-COM-2P).
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
Loosely based on a patch by
Jaswinder Singh Rajput <jaswinderlinux@gmail.com>.
KMS support by Dave Airlie <airlied@redhat.com>.
For Radeon 100- to 500-series, firmware blobs look like:
struct {
__be32 datah;
__be32 datal;
} cp_ucode[256];
For Radeon 600-series, there are two separate firmware blobs:
__be32 me_ucode[PM4_UCODE_SIZE * 3];
__be32 pfp_ucode[PFP_UCODE_SIZE];
For Radeon 700-series, likewise:
__be32 me_ucode[R700_PM4_UCODE_SIZE];
__be32 pfp_ucode[R700_PFP_UCODE_SIZE];
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
- Better small packet receive performance.
- Better handling of Flow control on 5709.
- Fixed iSCSI TMP ABORT TASK problem.
- Added iSCSI TCP timestamp option.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Image format is IHEX, one record for each pipe in order (record
addresses are ignored).
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>
The new FW improves the packets per second rate. It required a lot of change in
the FW which implies many changes in the driver to support it. It is now also
possible for the driver to use a separate MSI-X vector for Rx and Tx - this also
add some to the complicity of this change.
All things said - after this patch, practically all performance matrixes show
improvement.
Though Vladislav Zolotarov is not signed on this patch, he did most of the job
and deserves credit for that.
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
use request_firmware() to load the phy's EDC programmation
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
3c589_cs,3c574_cs,serial_cs:
(1)add cis(firmware) of 3Com lan&modem mulitifunction pcmcia card.
(2)load correct configuration register for 3Com card
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
>From now on FW will be downloaded from the binary file using request_firmware.
There will be different files for every supported chip. Currently 57710 (e1) and
57711 (e1h).
File names have the following format: bnx2x-<chip version>-<FW version>.fw.
ihex versions of current FW files are submitted in the next patch.
Each binary file has a header in the following format:
struct bnx2x_fw_file_section {
__be32 len;
__be32 offset;
}
struct bnx2x_fw_file_hdr {
struct bnx2x_fw_file_section init_ops;
struct bnx2x_fw_file_section init_ops_offsets;
struct bnx2x_fw_file_section init_data;
struct bnx2x_fw_file_section tsem_int_table_data;
struct bnx2x_fw_file_section tsem_pram_data;
struct bnx2x_fw_file_section usem_int_table_data;
struct bnx2x_fw_file_section usem_pram_data;
struct bnx2x_fw_file_section csem_int_table_data;
struct bnx2x_fw_file_section csem_pram_data;
struct bnx2x_fw_file_section xsem_int_table_data;
struct bnx2x_fw_file_section xsem_pram_data;
struct bnx2x_fw_file_section fw_version;
}
Each bnx2x_fw_file_section contains the length and the offset of the appropriate
section in the binary file. Values are stored in the big endian format.
Data types of arrays:
init_data __be32
init_ops_offsets __be16
XXsem_pram_data u8
XXsem_int_table_data u8
init_ops struct raw_op {
u8 op;
__be24 offset;
__be32 data;
}
fw_version u8
>From now boundaries of a specific initialization stage are stored in
init_ops_offsets array instead of being defined by separate macroes. The index
in init_ops_offsets is calculated by BLOCK_OPS_IDX macro:
#define BLOCK_OPS_IDX(block, stage, end) \
(2*(((block)*STAGE_IDX_MAX) + (stage)) + (end))
Security:
In addition to sanity check of array boundaries bnx2x will check a FW version.
Additional checks might be added in the future.
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Vladislav Zolotarov <vladz@broadcom.com>
Signed-off-by: Eilon Greenstein <eilong@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
pcnet_cs: add cis(firmware) of the Allied Telesis LA-PCM
Signed-off-by: Ken Kawasaki <ken_kawasaki@spring.nifty.jp>
Signed-off-by: David S. Miller <davem@davemloft.net>
These are available elsewhere (for example in the linux-firmware.git
repository); they have no business being added to the kernel source
tree.
We are only putting stuff in the firmware/ directory of the kernel
source when it's extracted from long-standing drivers which used to
include it directly.
We didn't intend to open the floodgates to including megabytes of new
firmware which was previously being distributed separately.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6:
b44: Use kernel DMA addresses for the kernel DMA API
forcedeth: Fix resume from hibernation regression.
xfrm: fix fragmentation on inter family tunnels
ibm_newemac: Fix dangerous struct assumption
gigaset: documentation update
gigaset: in file ops, check for device disconnect before anything else
bas_gigaset: use tasklet_hi_schedule for timing critical tasklets
net/802/fddi.c: add MODULE_LICENSE
smsc911x: remove unused #include <linux/version.h>
axnet_cs: fix phy_id detection for bogus Asix chip.
bnx2: Use request_firmware()
b44: Fix sizes passed to b44_sync_dma_desc_for_{device,cpu}()
socket: use percpu_add() while updating sockets_in_use
virtio_net: Set the mac config only when VIRITO_NET_F_MAC
myri_sbus: use request_firmware
e1000: fix loss of multicast packets
vxge: should include tcp.h
Conflict in firmware/WHENCE (SCSI vs net firmware)
Always use request_firmware() for loading yss225_registers image.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This reverts a hunk of commit 4b29631db3
which seems to have been an accident, and which re-introduced a
previously fixed bug.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This reverts commit 8b249b6856.
This 'fix' is not necessary; we just need to undo the damage caused
accidentally by Igor/Mauro in 4b29631db3
("V4L/DVB (9533): cx88: Add support for TurboSight TBS8910 DVB-S PCI card")
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Based on original patch by Ben Hutchings <ben@decadent.org.uk> and
Bastian Blank <waldi@debian.org>, with the following main changes:
Separated the mips firmware and rv2p firmware into different files
to make it easier to update them separately.
Added some code to fixup the rv2p code with run-time information
such as PAGE_SIZE.
Update version to 2.0.0.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware blob looks like this...
__be16 lanai4_data_size
unsigned char lanai4_code[]
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Specify a license for the Alacritech Sahara (10Gbe) and SLICOSS (1GBE)
firmware files.
Signed-off-by: Christopher Harrer <charrer@alacritech.com>
Signed-off-by: Mithlesh Thukral <mithlesh@linsyssoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Add support for downloading the firmware using kernel-builtin mechanism.
This will remove the need for the firmware files in the driver source code.
Signed-off-by: Christopher Harrer <charrer@alacritech.com>
Signed-off-by: Mithlesh Thukral <mithlesh@linsyssoft.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Adds the firmware to the firmware directory in ihex format so it can be
installed when doing make firmware_install.
Also update the firmware location in the driver code so it can locate
the files in the right place.
This should conclude the move to request_firmware().
Signed-off-by: Lior Dotan <liodot@gmail.com>
Cc: Christopher Harrer <charrer@alacritech.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Firmware blob is little endian
Thanks to Stephen Rothwell for fixing typos
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Firmware blob is little endian looks like this...
unsigned char Version1
unsigned char Version2
unsigned char Version3
unsigned char Padding
unsigned short start_address
unsigned short data
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: James Bottomley <James.Bottomley@HansenPartnership.com>
Based on a patch by Jaswinder Singh <jaswinder@infradead.org>.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware blob is little endian.
Compile-tested only.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the Multi-Tech cellular modem firmware to the TI USB serial driver.
This firmware was extracted from:
ftp://ftp.multitech.com/wireless/wireless_linux.zip
Firmware licence: "all firmware components are redistributable in binary
form" per support@multitech.com
Copyright (C) 2005 Multi-Tech Systems, Inc.
Signed-off-by: Chris Adams <cmadams@hiwaay.net>
Signed-off-by: Alan Cox <alan@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Thanks to David Woodhouse for help.
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rafael reported:
I get the following error from 'make modules_install' on my test boxes:
HOSTCC firmware/ihex2fw
/home/rafael/src/linux-2.6/firmware/ihex2fw.c:268: fatal error: opening dependency file firmware/.ihex2fw.d: Read-only file system
compilation terminated.
make[3]: *** [firmware/ihex2fw] Error 1
make[2]: *** [_modinst_post] Error 2
make[1]: *** [sub-make] Error 2
make: *** [all] Error 2
where the configuration is that the kernel is compiled on a build box
with 'make O=<destdir> -j5' and then <destdir> is mounted over NFS read-only by
each test box (full path to this directory is the same on the build box and on
the test boxes). Then, I cd into <destdir>, run 'make modules_install' and get
the error above.
The issue turns out to be that we when we install firmware pick
up the list of firmware blobs from firmware/Makefile.
And this triggers the Makefile rules to update ihex2fw.
There were two solutions for this issue:
1) Move the list of firmware blobs to a separate file
2) Avoid ihex2fw rebuild by moving it to scripts
As I seriously beleive that the list of firmware blobs should be
done in a fundamental different way solution 2) was selected.
Reported-and-tested-by: "Rafael J. Wysocki" <rjw@sisk.pl>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Make firmware/dsp56k/bootstrap.asm buildable on a56, the free Motorola
DSP56001 assembler (http://www.zdomain.com/a56.html).
Summary of changes:
- Remove '<' and '>' candy (they specify explicit addressing modes,
which a56 don't grok, but uses implicitly anyway).
- Replace 'move' with 'movem' when accessing program memory.
- Rename a few labels to avoid duplicates (which a56 can't handle).
Signed-off-by: Robert Millan <rmh@aybabtu.com>
Cc: Jaswinder Singh <jaswinder@infradead.org>
Cc: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-2.6: (44 commits)
qlge: Fix sparse warnings for tx ring indexes.
qlge: Fix sparse warning regarding rx buffer queues.
qlge: Fix sparse endian warning in ql_hw_csum_setup().
qlge: Fix sparse endian warning for inbound packet control block flags.
qlge: Fix sparse warnings for byte swapping in qlge_ethool.c
myri10ge: print MAC and serial number on probe failure
pkt_sched: cls_u32: Fix locking in u32_change()
iucv: fix cpu hotplug
af_iucv: Free iucv path/socket in path_pending callback
af_iucv: avoid left over IUCV connections from failing connects
af_iucv: New error return codes for connect()
net/ehea: bitops work on unsigned longs
Revert "net: Fix for initial link state in 2.6.28"
tcp: Kill extraneous SPLICE_F_NONBLOCK checks.
tcp: don't mask EOF and socket errors on nonblocking splice receive
dccp: Integrate the TFRC library with DCCP
dccp: Clean up ccid.c after integration of CCID plugins
dccp: Lockless integration of CCID congestion-control plugins
qeth: get rid of extra argument after printk to dev_* conversion
qeth: No large send using EDDP for HiperSockets.
...
Firmware blob looks like this...
u8 firmware_major
u8 firmware_minor
u8 firmware_fix
u8 pad
__be32 start_address
__be32 length (total, including BSS sections to be zeroed)
data... (in __be32 words, which is native for the firmware)
Signed-off-by: Jaswinder Singh Rajput <jaswinderrajput@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We store the firmware in its native big-endian form now, so the loop in
ace_copy() is modified to use be32_to_cpup() when writing it out.
We can forget the BSS,SBSS sections of the firmware, since we were
clearing all the device's RAM anyway. And the text,rodata,data sections
can all be loaded as a single chunk since they're contiguous (give or
take a few dozen bytes in between).
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Jes Sorensen <jes@sgi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The card based on stv0299 or stv0288 demodulators.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Include firmware and protocol images in the kernel image if requested
Signed-off-by: Divy Le Ray <divy@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Firmware blob looks like this...
__le16 load_address
unsigned char data[]
[akpm@linux-foundation.org: include vmalloc.h]
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix both the IHEX firmware generation (len field always null, and EOF
marker a byte too short) and loading (struct ihex_binrec needs to be
packed to reflect the on-disk structure).
Signed-off-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Provide a .gitignore file, and fix a typo which prevented some of the
generated binary files from being removed on 'make clean'.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Reported-and-tested-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
We're not updating the tg3 driver to use request_firmware() yet, but a
reference to its firmware accidentally slipped in as part of commit
c4667746 ("dabusb: use request_firmware()"). Remove it again.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Reported-by: Yinghai Lu <yhlu.kernel@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
When CONFIG_EXTRA_FIRMWARE_DIR gets changed, the filename in the .S file
(which uses .incbin to include the binary) needs to change. When we
renamed the BUILTIN_FIRMWARE_DIR option to EXTRA_FIRMWARE_DIR, we forgot
to update the manual dependency in firmware/Makefile, so it was
depending on a non-existent file in include/config/
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Version number provided in first HEX record.
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Although it wasn't actually using ihex records before, we use the Intel
HEX record format for this firmware -- because that gives us a simple
way to split it into separate chunks internally as we need, without
loading each part as a separate file.
Signed-off-by: Jaswinder Singh <jaswinder@infradead.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Since it had various regions to be loaded to separate addresses, and it
wanted to do them in fairly small chunks anyway, switch it to use the
new ihex code. Encode the start address in the first record.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Acked-by: Chas Williams <chas@cmf.nrl.navy.mil>
Some drivers could do with using records like Intel HEX, but with each
record being larger than 256 bytes. This has been possible in the binary
representation (struct ihex_binrec) in the kernel since the beginning --
at least of the the current version of history. But we haven't been able
to represent that in the .HEX files which get converted to .fw files.
This adds a '-w' option to ihex2fw to make it interpret the first _two_
bytes of each line as the record length, instead of only one byte. And
adds makefile rules for %.H16->%.fw which use that.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Not the straight conversion to binary which objcopy can do for us, but
actually representing each record with its original {addr, length},
because some drivers need that information preserved.
Fix up 'firmware_install' to be able to build $(hostprogs-y) too.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
For 'make modules_install', install any firmware required by
the modules which are being installed.
Also add a 'make firmware_install' target which doesn't depend on the
configuration, but installs _all_ available in-kernel-tree firmware into
$(INSTALL_FW_PATH), which defaults to /lib/firmware. This is intended
for distributors to make arch-independent (and config-independent)
packages containing firmware.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
This will control whether we build firmware into the kernel image for
_every_ driver which we convert to request_firmware(), to avoid a
proliferation of 'CONFIG_XXX_FIRMWARE' options for each one.
Default to 'y' for now, which is the wrong thing to do but people seem
to be insisting on it and refusing to even review patches until it's
done. And it does preserve the existing behaviour for built-in drivers.
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
This allows arbitrary firmware files to be included in the static kernel
where the firmware loader can find them without requiring userspace to
be alive.
(Updated and CONFIG_EXTRA_FIRMWARE_DIR added with lots of help from
Johannes Berg).
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Ken Kawasaki