It is not used anywhere except net/core/dev.c now.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
vlan_features contains features inherited from underlying device.
NETIF_SOFT_FEATURES are not inherited but belong to the vlan device
itself (ensured in vlan_dev_fix_features()).
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the fact that ORing with zero is a no-op.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove wrong setting of dev->flags. NETIF_F_NO_CSUM maps to IFF_DEBUG
there, so looks like a mistake.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
Set the init value before reset in probe function. And then just
modify the relative bits and keep the init settings.
For 8110S, 8110SB, and 8110SC series, the initial value of RxConfig
needs to be set after the tx/rx is enabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Only 8111b needs to enable rx when shutdowning with WoL.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Only 8111E needs enable RxConfig bit 0 ~ 3 when suspending or
shutdowning for wake on lan.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
Add the ERI functions which would be used by the new chips.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
- Disable tx and rx by resetting hw, so replace rtl8169_asic_down
with rtl8169_hw_reset.
- RxConfig bits 0 ~ 5 have to be cleared before hw reset to avoid
receiving spurious data.
- Certain chips need to do some checking before reset.
- Remove hw reset which is done before hw_start. It is done in close,
down or device probe functions.
- Move rtl8169_init_ring_indexes function into rtl_hw_reset function.
The indexes of tx and rx only need to be zero when the hw resets.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Acked-by: Francois Romieu <romieu@fr.zoreil.com>
* git://git.kernel.org/pub/scm/linux/kernel/git/steve/gfs2-2.6-fixes:
GFS2: Resolve inode eviction and ail list interaction bug
GFS2: Fix race during filesystem mount
GFS2: force a log flush when invalidating the rindex glock
Reset card->tx_dma_progress when lv1_net_start_tx_dma() fails or it
won't send anything afterwards anymore
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Revert to a proper state when gelic_card_kick_txdma() fails:
- Don't trigger BUG_ON when releasing the unsent tx descriptor
- Reset the tx chain head since the tail was not modified and
hence not in sync
- Unlink the released descriptor bus address from its predecessor
Signed-off-by: Andre Heider <a.heider@gmail.com>
Acked-by: Geoff Levand <geoff@infradead.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Change FW dump capture mask to a defult value, instead of using the recommended
value from the FW. This was done to keep the capture mask consistent with other
function drivers.
o Update driver version to 5.0.21
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Defined error code such as fw not responding, test already running and
cable not connected.
o Check Fw capability before performing loopback test.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As soon as skb is given to hardware, TX completion can free skb under us.
Therefore, we should update dev stats before kicking the device.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
MAC learning is required in bridge mode.
During bridge mode device will be put in promiscous mode.
Signed-off-by: Sucheta Chakraborty <sucheta.chakraborty@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added QME8242-k 10GbE Dual Port Mezzanine Card to supported card info.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Chip reset logic (IDC logic) has changed with fw dump support.
This broked compatibility with driver using older IDC logic.
Changes to make it compatible with drivers using older IDC logic.
Signed-off-by: Sritej Velaga <sritej.velaga@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The scratchpad location that we were reading from has not been
initialized yet during ->probe(), so we were getting inaccurate
information.
Update version to 2.1.10.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to help debug issues related to management firmware.
Signed-off-by: Jeffrey Huang <huangjw@broadcom.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
to allow iSCSI connection to fail faster instead of waiting for the
long timeout.
Update version to 2.5.6.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Latest bnx2x driver uses different CID for the iSCSI rings, so
we need to pass it in the ring init data. The rx ring is also
zeroed out to prevent stale DMA addresses from being used after
shutdown.
The same cp local variable redefined inside the else branch is
also eliminated.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CHIP_2_PORT_MODE was not set correctly.
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Suggested by Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: Michael Chan <mchan@broadcom.com>
Reviewed-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the driver state (and power source) is being more intensely
scrutinized, we need to make sure it is correct 100% of the time. This
patch finds and fixes all dangling power state transitions.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds code to update the status of the function to a common
location to the critical section added in the previous patch.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The code that performs the power source switching will need to consider
the status of the other devices before making any switches. The status
updates and power source switching will need to be an atomic operation,
so a critical section will be needed. This patch establishes the
critical section through a CPMU mutex.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tg3 devices will need to know exactly what function number they are so
that they can communicate their status to the other functions. In a KVM
environment, the function number of a device presented by the kernel
might not be the true function number, so an alternative method to
determine the function number is needed.
This patch used to contain an implementation for the alternative method,
but recently we discovered a hardware bug that renders it incorrect.
While new method is not yet known, it is still useful to consolidate the
code that determines the PCI function to one location and use the
results throughout the code.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently pci_set_power_state() does not return useful return codes for
transitions to the D0 power state. If a device refuses to go into D0,
the PCI layer issues a warning but returns success.
Entering into D0 is a requirement for correct operation of tg3 devices
though. If the PCI layer should be changed to return an error code for
this type of failure, the tg3 driver would be interested in catching it
and reacting to it. This patch makes the necessary modifications.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The tg3 driver is going to require memory mapped register access much
sooner than before. This patch makes sure the device is in the D0 power
state as soon as possible, and moves the code that enables the memory
arbiter outside tg3_get_eeprom_hw_cfg() where it can be more easily
monitored.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The following patch will require the driver to communicate with the APE
much sooner than before. This patch make sure the APE registers are
memory mapped and that the ENABLE_APE bit is set before the first use.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently we flush tp_status and then flush the remainder of the header+payload.
tp_status should be flushed in the end to avoid stale data being read by user-space.
Incorrectly re-ordered barriers in v1.
Signed-off-by: Chetan Loke <loke.chetan@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that there is a one-to-one correspondance between neighbour
and hh_cache entries, we no longer need:
1) dynamic allocation
2) attachment to dst->hh
3) refcounting
Initialization of the hh_cache entry is indicated by hh_len
being non-zero, and such initialization is always done with
the neighbour's lock held as a writer.
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch contains a few misc fixes which resolve a recently
reported issue. This patch has been a real team effort and has
received a lot of testing.
The first issue is that the ail lock needs to be held over a few
more operations. The lock thats added into gfs2_releasepage() may
possibly be a candidate for replacing with RCU at some future
point, but at this stage we've gone for the obvious fix.
The second issue is that gfs2_write_inode() can end up calling
a glock recursively when called from gfs2_evict_inode() via the
syncing code, so it needs a guard added.
The third issue is that we either need to not truncate the metadata
pages of inodes which have zero link count, but which we cannot
deallocate due to them still being in use by other nodes, or we need
to ensure that those pages have all made it through the journal and
ail lists first. This patch takes the former approach, but the
latter has also been tested and there is nothing to choose between
them performance-wise. So again, we could revise that decision
in the future.
Also, the inode eviction process is now better documented.
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
Tested-by: Bob Peterson <rpeterso@redhat.com>
Tested-by: Abhijith Das <adas@redhat.com>
Reported-by: Barry J. Marson <bmarson@redhat.com>
Reported-by: David Teigland <teigland@redhat.com>
Commit 28c2103 added new state ACPI_STATE_D3_COLD, so the device power
states array must be expanded by one also.
v2: Use ACPI_D_STATE_COUNT instead of number 5 for the array size.
Reported-by: Dan Carpenter <error27@gmail.com>
Suggested-by: Oldřich Jedlička <oldium.pro@seznam.cz>
Signed-off-by: Lin Ming <ming.m.lin@intel.com>
Signed-off-by: Len Brown <len.brown@intel.com>
The firmware on some machine will report duplicated hardware error
source ID in HEST. This is considered a firmware bug. To provide
better warning message, this patch adds duplicated hardware error
source ID detecting and corresponding printk.
This patch fixes#37412 on kernel bugzilla:
https://bugzilla.kernel.org/show_bug.cgi?id=37412
Reported-by: marconifabio@ubuntu-it.org
Signed-off-by: Huang Ying <ying.huang@intel.com>
Tested-by: Mathias <janedo.spam@gmail.com>
Signed-off-by: Len Brown <len.brown@intel.com>
As Simon reported, digital TV broke with mt20xx tuner due to
commit ad020dc2fe.
The mt20xx tuner passes V4L2_TUNER_DIGITAL_TV to tuner core. However, the
check_mode code now doesn't handle it well. Change the logic there to
avoid the breakage, and fix a test for analog-only at g_tuner.
Reported-by: Simon Arlott <simon@fire.lp0.eu>
Tested-by: Simon Arlott <simon@fire.lp0.eu>
Cc: stable@kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
Attached is a patch which addresses a race condition in the DVB core
related to closing/reopening the DVB frontend device in quick
succession. This is the reason that devices such as the HVR-1300,
HVR-3000, and HVR-4000 have been failing to scan properly under MythTV
and w_scan.
The gory details of the race are described in the patch.
Devin
There is a race condition exhibited when channel scanners such as w_scan and
MythTV quickly close and then reopen the frontend device node.
Under normal conditions, the behavior is as follows:
1. Application closes the device node
2. DVB frontend ioctl calls dvb_frontend_release which sets
fepriv->release_jiffies
3. DVB frontend thread *eventually* calls dvb_frontend_is_exiting() which
compares fepriv->release_jiffies, and shuts down the thread if timeout has
expired
4. Thread goes away
5. Application opens frontend device
6. DVB frontend ioctl() calls ts_bus_ctrl(1)
7. DVB frontend ioctl() creates new frontend thread, which calls
dvb_frontend_init(), which has demod driver init() routine setup initial
register state for demod chip.
8. Tuning request is issued.
The race occurs when the application in step 5 performs the new open() call
before the frontend thread is shutdown. In this case the ts_bus_ctrl() call
is made, which strobes the RESET pin on the demodulator, but the
dvb_frontend_init() function never gets called because the frontend thread
hasn't gone away yet. As a result, the initial register config for the demod
is *never* setup, causing subsequent tuning requests to fail.
If there is time between the close and open (enough for the dvb frontend
thread to be torn down), then in that case the new frontend thread is created
and thus the dvb_frontend_init() function does get called.
The fix is to set the flag which forces reinitialization if we did in fact
call ts_bus_ctrl().
This problem has been seen on the HVR-1300, HVR-3000, and HVR-4000, and is
likely occuring on other designs as well where ts_bus_ctrl() actually strobes
the reset pin on the demodulator.
Note that this patch should supercede any patches submitted for the
1300/3000/4000 which remove the code that removes GPIO code in
cx8802_dvb_advise_acquire(), which have been circulating by users for some
time now...
Canonical tracking this issue in Launchpad 439163:
Thanks to Jon Sayers from Hauppauge and Florent Audebert from Anevia S.A. for
providing hardware to test/debug with.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Jon Sayers <j.sayers@hauppauge.co.uk>
Cc: Florent Audebert <florent.audebert@anevia.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
When CONFIG_SND is not enabled, radio-sf16fmr2 build fails with:
so make this driver depend on SND.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: linux-media@vger.kernel.org
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
* 'bugfixes' of git://git.linux-nfs.org/projects/trondmy/nfs-2.6:
SUNRPC: Fix use of static variable in rpcb_getport_async
NFSv4.1: update nfs4_fattr_bitmap_maxsz
SUNRPC: Fix a race between work-queue and rpc_killall_tasks
pnfs: write: Set mds_offset in the generic layer - it is needed by all LDs
* 'drm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/airlied/drm-2.6:
drm/radeon/kms/evergreen: emit SQ_LDS_RESOURCE_MGMT for blits
agp/intel: Fix typo in G4x_GMCH_SIZE_VT_2M
drm/radeon/kms: fix typo in read_disabled vbios code
drm/radeon/kms: use correct BUS_CNTL reg on rs600
drm/radeon/kms: fix backend map typo on juniper
drm/radeon/kms: fix regression in hotplug
Michał Mirosław