For the 32-bit kernel, as described in
6d92bc9d48 ("x86/build: Build compressed x86 kernels as PIE"),
pre-2.26 binutils generates R_386_32 relocations in PIE mode. Since the
startup code does not perform relocation, any reloc entry with R_386_32
will remain as 0 in the executing code.
Commit
974f221c84 ("x86/boot: Move compressed kernel to the end of the
decompression buffer")
added a new symbol _end but did not mark it hidden, which doesn't give
the correct offset on older linkers. This causes the compressed kernel
to be copied beyond the end of the decompression buffer, rather than
flush against it. This region of memory may be reserved or already
allocated for other purposes by the bootloader.
Mark _end as hidden to fix. This changes the relocation from R_386_32 to
R_386_RELATIVE even on the pre-2.26 binutils.
For 64-bit, this is not strictly necessary, as the 64-bit kernel is only
built as PIE if the linker supports -z noreloc-overflow, which implies
binutils-2.27+, but for consistency, mark _end as hidden here too.
The below illustrates the before/after impact of the patch using
binutils-2.25 and gcc-4.6.4 (locally compiled from source) and QEMU.
Disassembly before patch:
48: 8b 86 60 02 00 00 mov 0x260(%esi),%eax
4e: 2d 00 00 00 00 sub $0x0,%eax
4f: R_386_32 _end
Disassembly after patch:
48: 8b 86 60 02 00 00 mov 0x260(%esi),%eax
4e: 2d 00 f0 76 00 sub $0x76f000,%eax
4f: R_386_RELATIVE *ABS*
Dump from extract_kernel before patch:
early console in extract_kernel
input_data: 0x0207c098 <--- this is at output + init_size
input_len: 0x0074fef1
output: 0x01000000
output_len: 0x00fa63d0
kernel_total_size: 0x0107c000
needed_size: 0x0107c000
Dump from extract_kernel after patch:
early console in extract_kernel
input_data: 0x0190d098 <--- this is at output + init_size - _end
input_len: 0x0074fef1
output: 0x01000000
output_len: 0x00fa63d0
kernel_total_size: 0x0107c000
needed_size: 0x0107c000
Fixes: 974f221c84 ("x86/boot: Move compressed kernel to the end of the decompression buffer")
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200207214926.3564079-1-nivedita@alum.mit.edu
In preparation for being able to decompress into a buffer starting at a
different address than startup_32, save the calculated output address
instead of recalculating it later.
We now keep track of three addresses:
%edx: startup_32 as we were loaded by bootloader
%ebx: new location of compressed kernel
%ebp: start of decompression buffer
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200303221205.4048668-2-nivedita@alum.mit.edu
Link: https://lore.kernel.org/r/20200308080859.21568-16-ardb@kernel.org
The load address is compared with LOAD_PHYSICAL_ADDR using a signed
comparison currently (using jge instruction).
When loading a 64-bit kernel using the new efi32_pe_entry() point added by:
97aa276579 ("efi/x86: Add true mixed mode entry point into .compat section")
using Qemu with -m 3072, the firmware actually loads us above 2Gb,
resulting in a very early crash.
Use the JAE instruction to perform a unsigned comparison instead, as physical
addresses should be considered unsigned.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200301230436.2246909-6-nivedita@alum.mit.edu
Link: https://lore.kernel.org/r/20200308080859.21568-14-ardb@kernel.org
code32_start is meant for 16-bit real-mode bootloaders to inform the
kernel where the 32-bit protected mode code starts. Nothing in the
protected mode kernel except the EFI stub uses it.
efi_main() currently returns boot_params, with code32_start set inside it
to tell efi_stub_entry() where startup_32 is located. Since it was invoked
by efi_stub_entry() in the first place, boot_params is already known.
Return the address of startup_32 instead.
This will allow a 64-bit kernel to live above 4Gb, for example, and it's
cleaner as well.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Link: https://lore.kernel.org/r/20200301230436.2246909-5-nivedita@alum.mit.edu
Link: https://lore.kernel.org/r/20200308080859.21568-13-ardb@kernel.org
The following commit:
ef5a7b5eb1 ("efi/x86: Remove GDT setup from efi_main")
introduced GDT setup into the 32-bit kernel's startup_32, and reloads
the GDTR after relocating the kernel for paranoia's sake.
A followup commit:
32d009137a ("x86/boot: Reload GDTR after copying to the end of the buffer")
introduced a similar GDTR reload in the 64-bit kernel as well.
The GDTR is adjusted by (init_size-_end), however this may not be the
correct offset to apply if the kernel was loaded at a misaligned address
or below LOAD_PHYSICAL_ADDR, as in that case the decompression buffer
has an additional offset from the original load address.
This should never happen for a conformant bootloader, but we're being
paranoid anyway, so just store the new GDT address in there instead of
adding any offsets, which is simpler as well.
Fixes: ef5a7b5eb1 ("efi/x86: Remove GDT setup from efi_main")
Fixes: 32d009137a ("x86/boot: Reload GDTR after copying to the end of the buffer")
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Ard Biesheuvel <ardb@kernel.org>
Cc: linux-efi@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: x86@kernel.org
Link: https://lore.kernel.org/r/20200226230031.3011645-2-nivedita@alum.mit.edu
The 64-bit kernel will already load a GDT in startup_64, which is the
next function to execute after return from efi_main.
Add GDT setup code to the 32-bit kernel's startup_32 as well. Doing it
in the head code has the advantage that we can avoid potentially
corrupting the GDT during copy/decompression. This also removes
dependence on having a specific GDT layout setup by the bootloader.
Both startup_32 and startup_64 now clear interrupts on entry, so we can
remove that from efi_main as well.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Link: https://lore.kernel.org/r/20200202171353.3736319-6-nivedita@alum.mit.edu
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Pull x86 asm updates from Ingo Molnar:
"Misc updates:
- Remove last remaining calls to exception_enter/exception_exit() and
simplify the entry code some more.
- Remove force_iret()
- Add support for "Fast Short Rep Mov", which is available starting
with Ice Lake Intel CPUs - and make the x86 assembly version of
memmove() use REP MOV for all sizes when FSRM is available.
- Micro-optimize/simplify the 32-bit boot code a bit.
- Use a more future-proof SYSRET instruction mnemonic"
* 'x86-asm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/boot: Simplify calculation of output address
x86/entry/64: Add instruction suffix to SYSRET
x86: Remove force_iret()
x86/cpufeatures: Add support for fast short REP; MOVSB
x86/context-tracking: Remove exception_enter/exit() from KVM_PV_REASON_PAGE_NOT_PRESENT async page fault
x86/context-tracking: Remove exception_enter/exit() from do_page_fault()
Condense the calculation of decompressed kernel start a little.
Committer notes:
before:
ebp = ebx - (init_size - _end)
after:
eax = (ebx + _end) - init_size
where in both ebx contains the temporary address the kernel is moved to
for in-place decompression.
The before and after difference in register state is %eax and %ebp
but that is immaterial because the compressed image is not built with
-mregparm, i.e., all arguments of the following extract_kernel() call
are passed on the stack.
Signed-off-by: Arvind Sankar <nivedita@alum.mit.edu>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200107194436.2166846-1-nivedita@alum.mit.edu
The various pointers we stash in the efi_config struct which we
retrieve using __efi_early() are simply copies of the ones in
the EFI system table, which we have started accessing directly
in the previous patch. So drop all the __efi_early() related
plumbing, as well as all the assembly code dealing with efi_config,
which allows us to move the PE/COFF entry point to C code as well.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191224151025.32482-18-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We use special wrapper routines to invoke firmware services in the
native case as well as the mixed mode case. For mixed mode, the need
is obvious, but for the native cases, we can simply rely on the
compiler to generate the indirect call, given that GCC now has
support for the MS calling convention (and has had it for quite some
time now). Note that on i386, the decompressor and the EFI stub are not
built with -mregparm=3 like the rest of the i386 kernel, so we can
safely allow the compiler to emit the indirect calls here as well.
So drop all the wrappers and indirection, and switch to either native
calls, or direct calls into the thunk routine for mixed mode.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
Cc: Arvind Sankar <nivedita@alum.mit.edu>
Cc: Borislav Petkov <bp@alien8.de>
Cc: James Morse <james.morse@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: https://lkml.kernel.org/r/20191224151025.32482-14-ardb@kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
These are all functions which are invoked from elsewhere, so annotate
them as global using the new SYM_FUNC_START and their ENDPROC's by
SYM_FUNC_END.
Now, ENTRY/ENDPROC can be forced to be undefined on X86, so do so.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Allison Randal <allison@lohutok.net>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Andy Shevchenko <andy@infradead.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Bill Metzenthen <billm@melbpc.org.au>
Cc: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Cc: Darren Hart <dvhart@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: linux-arch@vger.kernel.org
Cc: linux-crypto@vger.kernel.org
Cc: linux-efi <linux-efi@vger.kernel.org>
Cc: linux-efi@vger.kernel.org
Cc: linux-pm@vger.kernel.org
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: platform-driver-x86@vger.kernel.org
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20191011115108.12392-28-jslaby@suse.cz
.Lrelocated, .Lpaging_enabled, .Lno_longmode, and .Lin_pm32 are
self-standing local functions, annotate them as such and preserve "no
alignment".
The annotations do not generate anything yet.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Cao jin <caoj.fnst@cn.fujitsu.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Kate Stewart <kstewart@linuxfoundation.org>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: linux-arch@vger.kernel.org
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wei Huang <wei@redhat.com>
Cc: x86-ml <x86@kernel.org>
Cc: Xiaoyao Li <xiaoyao.li@linux.intel.com>
Link: https://lkml.kernel.org/r/20191011115108.12392-8-jslaby@suse.cz
Boris suggests to make a local label (prepend ".L") to these functions
to eliminate them from the symbol table. These are functions with very
local names and really should not be visible anywhere.
Note that objtool won't see these functions anymore (to generate ORC
debug info). But all the functions are not annotated with ENDPROC, so
they won't have objtool's attention anyway.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Cao jin <caoj.fnst@cn.fujitsu.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: "Kirill A. Shutemov" <kirill.shutemov@linux.intel.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Steve Winslow <swinslow@gmail.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Wei Huang <wei@redhat.com>
Cc: x86-ml <x86@kernel.org>
Cc: Xiaoyao Li <xiaoyao.li@linux.intel.com>
Link: https://lkml.kernel.org/r/20190906075550.23435-2-jslaby@suse.cz
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
The efi_pe_entry() body is somehow squashed into startup_32(). In the old days,
we forced startup_32() to start at offset 0x00 and efi_pe_entry() to start
at 0x10.
But this requirement was removed long time ago, in:
99f857db88 ("x86, build: Dynamically find entry points in compressed startup code")
The way it is now makes the code less readable and illogical. Given
we can now safely extract the inlined efi_pe_entry() body from
startup_32() into a separate function, we do so and we separate it to two
functions as they are marked already: efi_pe_entry() + efi32_stub_entry().
We also annotate the functions appropriatelly by ENTRY+ENDPROC.
ABI offset is preserved:
0000 128 FUNC GLOBAL DEFAULT 6 startup_32
0080 60 FUNC GLOBAL DEFAULT 6 efi_pe_entry
00bc 68 FUNC GLOBAL DEFAULT 6 efi32_stub_entry
On the top-level, it looked like this:
ENTRY(startup_32)
#ifdef CONFIG_EFI_STUB ; start of inlined
jmp preferred_addr
ENTRY(efi_pe_entry)
... ; a lot of assembly (efi_pe_entry)
ENTRY(efi32_stub_entry)
... ; a lot of assembly (efi32_stub_entry)
leal preferred_addr(%eax), %eax
jmp *%eax
preferred_addr:
#endif ; end of inlined
... ; a lot of assembly (startup_32)
ENDPROC(startup_32)
And it is now converted into:
ENTRY(startup_32)
... ; a lot of assembly (startup_32)
ENDPROC(startup_32)
#ifdef CONFIG_EFI_STUB
ENTRY(efi_pe_entry)
... ; a lot of assembly (efi_pe_entry)
ENDPROC(efi_pe_entry)
ENTRY(efi32_stub_entry)
... ; a lot of assembly (efi32_stub_entry)
leal startup_32(%eax), %eax
jmp *%eax
ENDPROC(efi32_stub_entry)
#endif
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: ard.biesheuvel@linaro.org
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/20170824073327.4129-1-jslaby@suse.cz
Signed-off-by: Ingo Molnar <mingo@kernel.org>
Provide the ability to perform mixed-mode runtime service calls for x86 in
the same way the following commit provided the ability to invoke for boot
services:
0a637ee612 ("x86/efi: Allow invocation of arbitrary boot services")
Suggested-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: David Howells <dhowells@redhat.com>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Matt Fleming <matt@codeblueprint.co.uk>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-efi@vger.kernel.org
Link: http://lkml.kernel.org/r/1486380166-31868-2-git-send-email-ard.biesheuvel@linaro.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
We currently allow invocation of 8 boot services with efi_call_early().
Not included are LocateHandleBuffer and LocateProtocol in particular.
For graphics output or to retrieve PCI ROMs and Apple device properties,
we're thus forced to use the LocateHandle + AllocatePool + LocateHandle
combo, which is cumbersome and needs more code.
The ARM folks allow invocation of the full set of boot services but are
restricted to our 8 boot services in functions shared across arches.
Thus, rather than adding just LocateHandleBuffer and LocateProtocol to
struct efi_config, let's rework efi_call_early() to allow invocation of
arbitrary boot services by selecting the 64 bit vs 32 bit code path in
the macro itself.
When compiling for 32 bit or for 64 bit without mixed mode, the unused
code path is optimized away and the binary code is the same as before.
But on 64 bit with mixed mode enabled, this commit adds one compare
instruction to each invocation of a boot service and, depending on the
code path selected, two jump instructions. (Most of the time gcc
arranges the jumps in the 32 bit code path.) The result is a minuscule
performance penalty and the binary code becomes slightly larger and more
difficult to read when disassembled. This isn't a hot path, so these
drawbacks are arguably outweighed by the attainable simplification of
the C code. We have some overhead anyway for thunking or conversion
between calling conventions.
The 8 boot services can consequently be removed from struct efi_config.
No functional change intended (for now).
Example -- invocation of free_pool before (64 bit code path):
0x2d4 movq %ds:efi_early, %rdx ; efi_early
0x2db movq %ss:arg_0-0x20(%rsp), %rsi
0x2e0 xorl %eax, %eax
0x2e2 movq %ds:0x28(%rdx), %rdi ; efi_early->free_pool
0x2e6 callq *%ds:0x58(%rdx) ; efi_early->call()
Example -- invocation of free_pool after (64 / 32 bit mixed code path):
0x0dc movq %ds:efi_early, %rax ; efi_early
0x0e3 cmpb $0, %ds:0x28(%rax) ; !efi_early->is64 ?
0x0e7 movq %ds:0x20(%rax), %rdx ; efi_early->call()
0x0eb movq %ds:0x10(%rax), %rax ; efi_early->boot_services
0x0ef je $0x150
0x0f1 movq %ds:0x48(%rax), %rdi ; free_pool (64 bit)
0x0f5 xorl %eax, %eax
0x0f7 callq *%rdx
...
0x150 movl %ds:0x30(%rax), %edi ; free_pool (32 bit)
0x153 jmp $0x0f5
Size of eboot.o text section:
CONFIG_X86_32: 6464 before, 6318 after
CONFIG_X86_64 && !CONFIG_EFI_MIXED: 7670 before, 7573 after
CONFIG_X86_64 && CONFIG_EFI_MIXED: 7670 before, 8319 after
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Matt Fleming <matt@codeblueprint.co.uk>
Since 'run_size' is now calculated in misc.c, the old script and associated
argument passing is no longer needed. This patch removes them, and renames
'run_size' to the more descriptive 'kernel_total_size'.
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
Signed-off-by: Baoquan He <bhe@redhat.com>
[ Rewrote the changelog, renamed 'run_size' to 'kernel_total_size' ]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Junjie Mao <eternal.n08@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: lasse.collin@tukaani.org
Link: http://lkml.kernel.org/r/1461888548-32439-6-git-send-email-keescook@chromium.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
This change makes later calculations about where the kernel is located
easier to reason about. To better understand this change, we must first
clarify what 'VO' and 'ZO' are. These values were introduced in commits
by hpa:
77d1a49995 ("x86, boot: make symbols from the main vmlinux available")
37ba7ab5e3 ("x86, boot: make kernel_alignment adjustable; new bzImage fields")
Specifically:
All names prefixed with 'VO_':
- relate to the uncompressed kernel image
- the size of the VO image is: VO__end-VO__text ("VO_INIT_SIZE" define)
All names prefixed with 'ZO_':
- relate to the bootable compressed kernel image (boot/compressed/vmlinux),
which is composed of the following memory areas:
- head text
- compressed kernel (VO image and relocs table)
- decompressor code
- the size of the ZO image is: ZO__end - ZO_startup_32 ("ZO_INIT_SIZE" define, though see below)
The 'INIT_SIZE' value is used to find the larger of the two image sizes:
#define ZO_INIT_SIZE (ZO__end - ZO_startup_32 + ZO_z_extract_offset)
#define VO_INIT_SIZE (VO__end - VO__text)
#if ZO_INIT_SIZE > VO_INIT_SIZE
# define INIT_SIZE ZO_INIT_SIZE
#else
# define INIT_SIZE VO_INIT_SIZE
#endif
The current code uses extract_offset to decide where to position the
copied ZO (i.e. ZO starts at extract_offset). (This is why ZO_INIT_SIZE
currently includes the extract_offset.)
Why does z_extract_offset exist? It's needed because we are trying to minimize
the amount of RAM used for the whole act of creating an uncompressed, executable,
properly relocation-linked kernel image in system memory. We do this so that
kernels can be booted on even very small systems.
To achieve the goal of minimal memory consumption we have implemented an in-place
decompression strategy: instead of cleanly separating the VO and ZO images and
also allocating some memory for the decompression code's runtime needs, we instead
create this elaborate layout of memory buffers where the output (decompressed)
stream, as it progresses, overlaps with and destroys the input (compressed)
stream. This can only be done safely if the ZO image is placed to the end of the
VO range, plus a certain amount of safety distance to make sure that when the last
bytes of the VO range are decompressed, the compressed stream pointer is safely
beyond the end of the VO range.
z_extract_offset is calculated in arch/x86/boot/compressed/mkpiggy.c during
the build process, at a point when we know the exact compressed and
uncompressed size of the kernel images and can calculate this safe minimum
offset value. (Note that the mkpiggy.c calculation is not perfect, because
we don't know the decompressor used at that stage, so the z_extract_offset
calculation is necessarily imprecise and is mostly based on gzip internals -
we'll improve that in the next patch.)
When INIT_SIZE is bigger than VO_INIT_SIZE (uncommon but possible),
the copied ZO occupies the memory from extract_offset to the end of
decompression buffer. It overlaps with the soon-to-be-uncompressed kernel
like this:
|-----compressed kernel image------|
V V
0 extract_offset +INIT_SIZE
|-----------|---------------|-------------------------|--------|
| | | |
VO__text startup_32 of ZO VO__end ZO__end
^ ^
|-------uncompressed kernel image---------|
When INIT_SIZE is equal to VO_INIT_SIZE (likely) there's still space
left from end of ZO to the end of decompressing buffer, like below.
|-compressed kernel image-|
V V
0 extract_offset +INIT_SIZE
|-----------|---------------|-------------------------|--------|
| | | |
VO__text startup_32 of ZO ZO__end VO__end
^ ^
|------------uncompressed kernel image-------------|
To simplify calculations and avoid special cases, it is cleaner to
always place the compressed kernel image in memory so that ZO__end
is at the end of the decompression buffer, instead of placing t at
the start of extract_offset as is currently done.
This patch adds BP_init_size (which is the INIT_SIZE as passed in from
the boot_params) into asm-offsets.c to make it visible to the assembly
code.
Then when moving the ZO, it calculates the starting position of
the copied ZO (via BP_init_size and the ZO run size) so that the VO__end
will be at the end of the decompression buffer. To make the position
calculation safe, the end of ZO is page aligned (and a comment is added
to the existing VO alignment for good measure).
Signed-off-by: Yinghai Lu <yinghai@kernel.org>
[ Rewrote changelog and comments. ]
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Dave Young <dyoung@redhat.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: lasse.collin@tukaani.org
Link: http://lkml.kernel.org/r/1461888548-32439-3-git-send-email-keescook@chromium.org
[ Rewrote the changelog some more. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The function "decompress_kernel" now performs many more duties, so this
patch renames it to "extract_kernel" and updates callers and comments.
Additionally the file header comment for misc.c is improved to actually
describe what is contained.
Suggested-by: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: Baoquan He <bhe@redhat.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Borislav Petkov <bp@suse.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: H.J. Lu <hjl.tools@gmail.com>
Cc: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Yinghai Lu <yinghai@kernel.org>
Link: http://lkml.kernel.org/r/1460997735-24785-5-git-send-email-keescook@chromium.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
The 32-bit x86 assembler in binutils 2.26 will generate R_386_GOT32X
relocation to get the symbol address in PIC. When the compressed x86
kernel isn't built as PIC, the linker optimizes R_386_GOT32X relocations
to their fixed symbol addresses. However, when the compressed x86
kernel is loaded at a different address, it leads to the following
load failure:
Failed to allocate space for phdrs
during the decompression stage.
If the compressed x86 kernel is relocatable at run-time, it should be
compiled with -fPIE, instead of -fPIC, if possible and should be built as
Position Independent Executable (PIE) so that linker won't optimize
R_386_GOT32X relocation to its fixed symbol address.
Older linkers generate R_386_32 relocations against locally defined
symbols, _bss, _ebss, _got and _egot, in PIE. It isn't wrong, just less
optimal than R_386_RELATIVE. But the x86 kernel fails to properly handle
R_386_32 relocations when relocating the kernel. To generate
R_386_RELATIVE relocations, we mark _bss, _ebss, _got and _egot as
hidden in both 32-bit and 64-bit x86 kernels.
To build a 64-bit compressed x86 kernel as PIE, we need to disable the
relocation overflow check to avoid relocation overflow errors. We do
this with a new linker command-line option, -z noreloc-overflow, which
got added recently:
commit 4c10bbaa0912742322f10d9d5bb630ba4e15dfa7
Author: H.J. Lu <hjl.tools@gmail.com>
Date: Tue Mar 15 11:07:06 2016 -0700
Add -z noreloc-overflow option to x86-64 ld
Add -z noreloc-overflow command-line option to the x86-64 ELF linker to
disable relocation overflow check. This can be used to avoid relocation
overflow check if there will be no dynamic relocation overflow at
run-time.
The 64-bit compressed x86 kernel is built as PIE only if the linker supports
-z noreloc-overflow. So far 64-bit relocatable compressed x86 kernel
boots fine even when it is built as a normal executable.
Signed-off-by: H.J. Lu <hjl.tools@gmail.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Brian Gerst <brgerst@gmail.com>
Cc: Denys Vlasenko <dvlasenk@redhat.com>
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-kernel@vger.kernel.org
[ Edited the changelog and comments. ]
Signed-off-by: Ingo Molnar <mingo@kernel.org>
There is already defined macro KEEP_SEGMENTS in
<asm/bootparam.h>, let's use it instead of hardcoded
constants.
Signed-off-by: Alexander Kuleshov <kuleshovmail@gmail.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Link: http://lkml.kernel.org/r/1424331298-7456-1-git-send-email-kuleshovmail@gmail.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
When choosing a random address, the current implementation does not take into
account the reversed space for .bss and .brk sections. Thus the relocated kernel
may overlap other components in memory. Here is an example of the overlap from a
x86_64 kernel in qemu (the ranges of physical addresses are presented):
Physical Address
0x0fe00000 --+--------------------+ <-- randomized base
/ | relocated kernel |
vmlinux.bin | (from vmlinux.bin) |
0x1336d000 (an ELF file) +--------------------+--
\ | | \
0x1376d870 --+--------------------+ |
| relocs table | |
0x13c1c2a8 +--------------------+ .bss and .brk
| | |
0x13ce6000 +--------------------+ |
| | /
0x13f77000 | initrd |--
| |
0x13fef374 +--------------------+
The initrd image will then be overwritten by the memset during early
initialization:
[ 1.655204] Unpacking initramfs...
[ 1.662831] Initramfs unpacking failed: junk in compressed archive
This patch prevents the above situation by requiring a larger space when looking
for a random kernel base, so that existing logic can effectively avoids the
overlap.
[kees: switched to perl to avoid hex translation pain in mawk vs gawk]
[kees: calculated overlap without relocs table]
Fixes: 82fa9637a2 ("x86, kaslr: Select random position from e820 maps")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Junjie Mao <eternal.n08@gmail.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Vivek Goyal <vgoyal@redhat.com>
Cc: Andi Kleen <ak@linux.intel.com>
Cc: stable@vger.kernel.org
Link: http://lkml.kernel.org/r/1414762838-13067-1-git-send-email-eternal.n08@gmail.com
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
This reverts commit 9cb0e39423.
It causes my Sony Vaio Pro 11 to immediately reboot at startup.
Acked-by: Ingo Molnar <mingo@kernel.org>
Cc: Peter Anvin <hpa@zytor.com>
Cc: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Cc: Matt Fleming <matt.fleming@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Maarten reported that his Macbook pro 8.2 stopped booting after commit
f23cf8bd5c ("efi/x86: efistub: Move shared dependencies to
<asm/efi.h>"), the main feature of which is changing the visibility of
symbol 'efi_early' from local to global.
By making 'efi_early' global we end up requiring an entry in the Global
Offset Table. Unfortunately, while we do include code to fixup GOT
entries in the early boot code, it's only called after we've executed
the EFI boot stub.
What this amounts to is that references to 'efi_early' in the EFI boot
stub don't point to the correct place.
Since we've got multiple boot entry points we need to be prepared to
fixup the GOT in multiple places, while ensuring that we never do it
more than once, otherwise the GOT entries will still point to the wrong
place.
Reported-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Tested-by: Maarten Lankhorst <maarten.lankhorst@canonical.com>
Cc: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
code32_start should point at the start of the protected mode code, and
*not* at the beginning of the bzImage. This is much easier to do in
assembly so document that callers of make_boot_params() need to fill out
code32_start.
The fallout from this bug is that we would end up relocating the image
but copying the image at some offset, resulting in what appeared to be
memory corruption.
Reported-by: Thomas Bächler <thomas@archlinux.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The kbuild test robot reported the following errors, introduced with
commit 54b52d8726 ("x86/efi: Build our own EFI services pointer
table"),
arch/x86/boot/compressed/head_32.o: In function `efi32_config':
>> (.data+0x58): undefined reference to `efi_call_phys'
arch/x86/boot/compressed/head_64.o: In function `efi64_config':
>> (.data+0x90): undefined reference to `efi_call6'
Wrap the efi*_config structures in #ifdef CONFIG_EFI_STUB so that we
don't make references to EFI functions if they're not compiled in.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
The EFI handover code only works if the "bitness" of the firmware and
the kernel match, i.e. 64-bit firmware and 64-bit kernel - it is not
possible to mix the two. This goes against the tradition that a 32-bit
kernel can be loaded on a 64-bit BIOS platform without having to do
anything special in the boot loader. Linux distributions, for one thing,
regularly run only 32-bit kernels on their live media.
Despite having only one 'handover_offset' field in the kernel header,
EFI boot loaders use two separate entry points to enter the kernel based
on the architecture the boot loader was compiled for,
(1) 32-bit loader: handover_offset
(2) 64-bit loader: handover_offset + 512
Since we already have two entry points, we can leverage them to infer
the bitness of the firmware we're running on, without requiring any boot
loader modifications, by making (1) and (2) valid entry points for both
CONFIG_X86_32 and CONFIG_X86_64 kernels.
To be clear, a 32-bit boot loader will always use (1) and a 64-bit boot
loader will always use (2). It's just that, if a single kernel image
supports (1) and (2) that image can be used with both 32-bit and 64-bit
boot loaders, and hence both 32-bit and 64-bit EFI.
(1) and (2) must be 512 bytes apart at all times, but that is already
part of the boot ABI and we could never change that delta without
breaking existing boot loaders anyhow.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
It's not possible to dereference the EFI System table directly when
booting a 64-bit kernel on a 32-bit EFI firmware because the size of
pointers don't match.
In preparation for supporting the above use case, build a list of
function pointers on boot so that callers don't have to worry about
converting pointer sizes through multiple levels of indirection.
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
This allows decompress_kernel to return a new location for the kernel to
be relocated to. Additionally, enforces CONFIG_PHYSICAL_START as the
minimum relocation position when building with CONFIG_RELOCATABLE.
With CONFIG_RANDOMIZE_BASE set, the choose_kernel_location routine
will select a new location to decompress the kernel, though here it is
presently a no-op. The kernel command line option "nokaslr" is introduced
to bypass these routines.
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/1381450698-28710-3-git-send-email-keescook@chromium.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Moves the relocation handling into C, after decompression. This requires
that the decompressed size is passed to the decompression routine as
well so that relocations can be found. Only kernels that need relocation
support will use the code (currently just x86_32), but this is laying
the ground work for 64-bit using it in support of KASLR.
Based on work by Neill Clift and Michael Davidson.
Signed-off-by: Kees Cook <keescook@chromium.org>
Link: http://lkml.kernel.org/r/20130708161517.GA4832@www.outflux.net
Acked-by: Zhang Yanfei <zhangyanfei@cn.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
We have historically hard-coded entry points in head.S just so it's easy
to build the executable/bzImage headers with references to them.
Unfortunately, this leads to boot loaders abusing these "known" addresses
even when they are *explicitly* told that they "should look at the ELF
header to find this address, as it may change in the future". And even
when the address in question *has* actually been changed in the past,
without fanfare or thought to compatibility.
Thus we have bootloaders doing stunningly broken things like jumping
to offset 0x200 in the kernel startup code in 64-bit mode, *hoping*
that startup_64 is still there (it has moved at least once
before). And hoping that it's actually a 64-bit kernel despite the
fact that we don't give them any indication of that fact.
This patch should hopefully remove the temptation to abuse internal
addresses in future, where sternly worded comments have not sufficed.
Instead of having hard-coded addresses and saying "please don't abuse
these", we actually pull the addresses out of the ELF payload into
zoffset.h, and make build.c shove them back into the right places in
the bzImage header.
Rather than including zoffset.h into build.c and thus having to rebuild
the tool for every kernel build, we parse it instead. The parsing code
is small and simple.
This patch doesn't actually move any of the interesting entry points, so
any offending bootloader will still continue to "work" after this patch
is applied. For some version of "work" which includes jumping into the
compressed payload and crashing, if the bzImage it's given is a 32-bit
kernel. No change there then.
[ hpa: some of the issues in the description are addressed or
retconned by the 2.12 boot protocol. This patch has been edited to
only remove fixed addresses that were *not* thus retconned. ]
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Link: http://lkml.kernel.org/r/1358513837.2397.247.camel@shinybook.infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
If the bootloader calls the EFI handover entry point as a standard function
call, then it'll have a return address on the stack. We need to pop that
before calling efi_main(), or the arguments will all be out of position on
the stack.
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
Cc: <stable@kernel.org>
Link: http://lkml.kernel.org/r/1358513837.2397.247.camel@shinybook.infradead.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: Matt Fleming <matt.fleming@intel.com>
As things currently stand, traditional EFI boot loaders and the EFI
boot stub are carrying essentially the same initialisation code
required to setup an EFI machine for booting a kernel. There's really
no need to have this code in two places and the hope is that, with
this new protocol, initialisation and booting of the kernel can be
left solely to the kernel's EFI boot stub. The responsibilities of the
boot loader then become,
o Loading the kernel image from boot media
File system code still needs to be carried by boot loaders for the
scenario where the kernel and initrd files reside on a file system
that the EFI firmware doesn't natively understand, such as ext4, etc.
o Providing a user interface
Boot loaders still need to display any menus/interfaces, for example
to allow the user to select from a list of kernels.
Bump the boot protocol number because we added the 'handover_offset'
field to indicate the location of the handover protocol entry point.
Cc: H. Peter Anvin <hpa@zytor.com>
Cc: Peter Jones <pjones@redhat.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Acked-and-Tested-by: Matthew Garrett <mjg@redhat.com>
Link: http://lkml.kernel.org/r/1342689828-16815-1-git-send-email-matt@console-pimps.org
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The method used to work out whether we were booted by EFI firmware or
via a boot loader is broken. Because efi_main() is always executed
when booting from a boot loader we will dereference invalid pointers
either on the stack (CONFIG_X86_32) or contained in %rdx
(CONFIG_X86_64) when searching for an EFI System Table signature.
Instead of dereferencing these invalid system table pointers, add a
new entry point that is only used when booting from EFI firmware, when
we know the pointer arguments will be valid. With this change legacy
boot loaders will no longer execute efi_main(), but will instead skip
EFI stub initialisation completely.
[ hpa: Marking this for urgent/stable since it is a regression when
the option is enabled; without the option the patch has no effect ]
Signed-off-by: Matt Fleming <matt.hfleming@intel.com>
Link: http://lkml.kernel.org/r/1334584744.26997.14.camel@mfleming-mobl1.ger.corp.intel.com
Reported-by: Jordan Justen <jordan.l.justen@intel.com>
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Cc: <stable@vger.kernel.org> v3.3
There is currently a large divide between kernel development and the
development of EFI boot loaders. The idea behind this patch is to give
the kernel developers full control over the EFI boot process. As
H. Peter Anvin put it,
"The 'kernel carries its own stub' approach been very successful in
dealing with BIOS, and would make a lot of sense to me for EFI as
well."
This patch introduces an EFI boot stub that allows an x86 bzImage to
be loaded and executed by EFI firmware. The bzImage appears to the
firmware as an EFI application. Luckily there are enough free bits
within the bzImage header so that it can masquerade as an EFI
application, thereby coercing the EFI firmware into loading it and
jumping to its entry point. The beauty of this masquerading approach
is that both BIOS and EFI boot loaders can still load and run the same
bzImage, thereby allowing a single kernel image to work in any boot
environment.
The EFI boot stub supports multiple initrds, but they must exist on
the same partition as the bzImage. Command-line arguments for the
kernel can be appended after the bzImage name when run from the EFI
shell, e.g.
Shell> bzImage console=ttyS0 root=/dev/sdb initrd=initrd.img
v7:
- Fix checkpatch warnings.
v6:
- Try to allocate initrd memory just below hdr->inird_addr_max.
v5:
- load_options_size is UTF-16, which needs dividing by 2 to convert
to the corresponding ASCII size.
v4:
- Don't read more than image->load_options_size
v3:
- Fix following warnings when compiling CONFIG_EFI_STUB=n
arch/x86/boot/tools/build.c: In function ‘main’:
arch/x86/boot/tools/build.c:138:24: warning: unused variable ‘pe_header’
arch/x86/boot/tools/build.c:138:15: warning: unused variable ‘file_sz’
- As reported by Matthew Garrett, some Apple machines have GOPs that
don't have hardware attached. We need to weed these out by
searching for ones that handle the PCIIO protocol.
- Don't allocate memory if no initrds are on cmdline
- Don't trust image->load_options_size
Maarten Lankhorst noted:
- Don't strip first argument when booted from efibootmgr
- Don't allocate too much memory for cmdline
- Don't update cmdline_size, the kernel considers it read-only
- Don't accept '\n' for initrd names
v2:
- File alignment was too large, was 8192 should be 512. Reported by
Maarten Lankhorst on LKML.
- Added UGA support for graphics
- Use VIDEO_TYPE_EFI instead of hard-coded number.
- Move linelength assignment until after we've assigned depth
- Dynamically fill out AddressOfEntryPoint in tools/build.c
- Don't use magic number for GDT/TSS stuff. Requested by Andi Kleen
- The bzImage may need to be relocated as it may have been loaded at
a high address address by the firmware. This was required to get my
macbook booting because the firmware loaded it at 0x7cxxxxxx, which
triggers this error in decompress_kernel(),
if (heap > ((-__PAGE_OFFSET-(128<<20)-1) & 0x7fffffff))
error("Destination address too large");
Cc: Mike Waychison <mikew@google.com>
Cc: Matthew Garrett <mjg@redhat.com>
Tested-by: Henrik Rydberg <rydberg@euromail.se>
Signed-off-by: Matt Fleming <matt.fleming@intel.com>
Link: http://lkml.kernel.org/r/1321383097.2657.9.camel@mfleming-mobl1.ger.corp.intel.com
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
In order for global variables and functions to work in the
decompressor, we need to fix up the GOT in assembly code.
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
LKML-Reference: <4C57382E.8050501@zytor.com>
This has the consequence of changing the section name use for head
code from ".text.head" to ".head.text".
Linus suggested that we merge the ".text.head" section with ".text"
(presumably while preserving the fact that the head code starts at 0).
When I tried this it caused the kernel to not boot.
Signed-off-by: Tim Abbott <tabbott@ksplice.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Sam Ravnborg <sam@ravnborg.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Make the kernel_alignment field adjustable; this allows us to set it
to a large value (intended to be 16 MB to avoid ZONE_DMA contention,
memory holes and other weirdness) while a smart bootloader can still
force a loading at a lesser alignment if absolutely necessary.
Also export pref_address (preferred loading address, corresponding to
the link-time address) and init_size, the total amount of linear
memory the kernel will require during initialization.
[ Impact: allows better kernel placement, gives bootloader more info ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Remove a couple of lines of dead code from
arch/x86/boot/compressed/head_*.S; all of these update registers that
are dead in the current code.
[ Impact: cleanup ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Determine the compressed code offset (from the kernel runtime address)
at compile time. This allows some minor optimizations in
arch/x86/boot/compressed/head_*.S, but more importantly it makes this
value available to the build process, which will enable a future patch
to export the necessary linear memory footprint into the bzImage
header.
[ Impact: cleanup, future patch enabling ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
In the pre-decompression code, use the appropriate largest possible
rep movs and rep stos to move code and clear bss, respectively. For
reverse copy, do note that the initial values are supposed to be the
address of the first (highest) copy datum, not one byte beyond the end
of the buffer.
rep strings are not necessarily the fastest way to perform these
operations on all current processors, but are likely to be in the
future, and perhaps more importantly, we want to encourage the
architecturally right thing to do here.
This also fixes a couple of trivial inefficiencies on 64 bits.
[ Impact: trivial performance enhancement, increase code similarity ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The 64-bit code already clears EFLAGS as soon as it has a stack. This
seems like a reasonable precaution, so do it on 32 bits as well.
[ Impact: extra paranoia ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Set up the decompression stack as soon as we know where it needs to
go. That way we have a full-service stack as soon as possible, rather
than relying on the BP_scratch field.
Note that the stack does need to be empty during bss zeroing (or
else the stack needs to be moved out of the bss segment, which is also
an option.)
[ Impact: cleanup, minor paranoia ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Both on 32 and 64 bits, we copy all the way up to the end of bss,
except that on 64 bits there is a hack to avoid copying on top of the
page tables. There is no point in copying bss at all, especially
since we are just about to zero it all anyway.
To clean up and unify the handling, we now do:
- copy from startup_32 to _bss.
- zero from _bss to _ebss.
- the _ebss symbol is aligned to an 8-byte boundary.
- the page tables are moved to a separate section.
Use _bss as the copy endpoint since _edata may be misaligned.
[ Impact: cleanup, trivial performance improvement ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Reformat arch/x86/boot/compressed/head_32.S to be closer to currently
preferred kernel assembly style, that is:
- opcode and operand separated by tab
- operands separated by ", "
- C-style comments
This also makes it more similar to head_64.S.
[ Impact: cleanup, no object code change ]
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Look at the:
diff -u arch/x86/boot/compressed/vmlinux_*.lds
output and realize that they're basially exactly the same except for
trivial naming differences, and the fact that the 64-bit version has a
"pgtable" thing.
So unify them.
There's some trivial cleanup there (make the output format a Kconfig thing
rather than doing #ifdef's for it, and unify both 32-bit and 64-bit BSS
end to "_ebss", where 32-bit used to use the traditional "_end"), but
other than that it's really very mindless and straigt conversion.
For example, I think we should aim to remove "startup_32" vs "startup_64",
and just call it "startup", and get rid of one more difference. I didn't
do that.
Also, notice the comment in the unified vmlinux.lds.S talks about
"head_64" and "startup_32" which is an odd and incorrect mix, but that was
actually what the old 64-bit only lds file had, so the confusion isn't
new, and now that mixing is arguably more accurate thanks to the
vmlinux.lds.S file being shared between the two cases ;)
[ Impact: cleanup, unification ]
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Arvind Sankar