This adds support for the DA7219 audio codec with built-in advanced
accessory detect features.
Signed-off-by: Adam Thomson <Adam.Thomson.Opensource@diasemi.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Richard Fitzgerald <rf@opensource.wolfsonmicro.com>
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The hdmi stub codec has not been used since refactoring of OMAP HDMI
audio support.
Signed-off-by: Jyri Sarha <jsarha@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for the InvenSense ICS-43432 I2S MEMS microphone.
This is a non-software-configurable MEMS microphone with I2S output.
Tested on a setup with a single ICS-43432 (the device itself supports
stereo operation using a hardware pin controlling left vs. right channel
output).
Signed-off-by: Ricard Wanderlof <ricardw@axis.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Codec part of the sti platform that supports codec IPs.
This first version does not support HDMI, but only DAC and SPDIF out.
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
This driver add PCM interface to a GTM601 UMTS modem chip.
There is no configuration interface.
Signed-off-by: Marek Belisko <marek@goldelico.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The patch separates the IO function from the rt286. It is prepared to share
for new chips that support the same IO function.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Introduce a new codec driver for the Texas Instruments
TAS5711/TAS5717/TAS5719 power amplifier chips. These chips are typically
used to take an I2S digital audio input and drive 10-20W into a pair of
speakers.
Signed-off-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Simplify dependencies by using new style split out bus interfaces.
Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add codec driver for the Maxim MAX98357A DAC.
Signed-off-by: Kenneth Westfield <kwestfie@codeaurora.org>
Acked-by: Banajit Goswami <bgoswami@codeaurora.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The TS3A227E is an autonomous audio accessory detection and
configuration switch that detects 3-pole or 4-pole audio accessories
and configures internal switches to route the signals accordingly.
This chip also has built-in support for the new button standard
described in the Android "Wired audio headset specification" v1.0.
These buttons will be reported on the jack as buttons 0-3 mapped to
KEY_MEDIA, KEY_VOLUMEUP, KEY_VOLUMEDOWN, and KEY_VOICE_COMMAND.
This will be added as an aux_dev and have the jack passed in from the
machine driver.
Signed-off-by: Dylan Reid <dgreid@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Create a separate module for rt5677 spi driver. Without
this patch, the build fails due to multiple defs of
'init_module' and 'cleanup_module'. module_spi_driver()
defines its own module, so it can't be part of the rt5677
module.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
The ALC5677 has a programmable DSP, and there is a SPI that is dadicated for DSP
firmware loading. Therefore, the patch includes a SPI driver for writing the DSP
firmware. The VAD(Voice Activaty Detection) has be implemented and use the DSP to
recognize the key phase.
Signed-off-by: Oder Chiou <oder_chiou@realtek.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Currently the cs4271 driver depends on SND_SOC_I2C_AND_SPI.
So the driver cannot be built as built-in if CONFIG_I2C=m.
Split SPI and I2C code into different modules to avoid this issue.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Analog Devices SSM4567 is a boost class-D audio amplifier.
Signed-off-by: Anatol Pomozov <anatol.pomozov@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add a codec driver for the Everest ES8328. It supports two separate audio
outputs and two separate audio inputs.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Cirrus Logic CS35L32 Boosted Amplifier
I2S output provides monitor data to the SOC/CODEC/DSP for speaker protection/enhancement algorithms
Signed-off-by: Brian Austin <brian.austin@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Support the TI TAS2552 Class D amplifier.
The TAS2552 is a high efficiency Class-D audio
power amplifier with advanced battery current
management and an integrated Class-G boost
The device constantly measures the
current and voltage across the load and provides a
digital stream of this information.
Signed-off-by: Dan Murphy <dmurphy@ti.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds Realtek ALC286 codec driver.
ALC286 is a dual mode codec, which can run as HD-A or I2S mode.
It is controlled by HD-A verb commands via I2C protocol.
The following is the I/O difference between ALC286 and general I2S codecs.
1. A HD-A verb command contains three parts, NID, VID, and PID.
And an I2S command contains only two parts: address and data.
2. Not only the register address is written, but the read command also
includes the entire write command.
3. rt286 uses different registers for read and write the same bits.
We map verb command to regmap structure. However, we read most registers from
cache to prevent the asymmetry read/write issue in rt286.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Gustaw Lewandowski <gustaw.lewandowski@intel.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds a minimum support of Realtek ALC5670 codec.
Signed-off-by: Bard Liao <bardliao@realtek.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
This patch adds support for the Cirrus Logic CS4265 Stereo I2C CODEC.
Signed-off-by: Paul Handrigan <paul.handrigan@cirrus.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
When the SigmaDSP module is built-in, but the I2C core is build as a module
we'll get a undefined reference:
sound/built-in.o: In function `sigma_action_write_i2c':
:(.text+0x5d8d4): undefined reference to `i2c_master_send'
This can happen if a audio driver that is using the regmap SigmaDSP interface is
built into the kernel, but core I2C support is build as a module. To fix this
split the SigmaDSP module into three modules, one module providing the core
infrastructure and two small modules implementing the regmap and I2C interfaces.
This allows e.g. the core infrastructure and regmap support to be built into the
kernel while I2C support can still be build as a module.
Fixes: dab464b60 ("ASoC: Add ADAU1361/ADAU1761 audio CODEC support")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
When the SigmaDSP module is built-in, but the I2C core is build as a module
we'll get a undefined reference:
sound/built-in.o: In function `sigma_action_write_i2c':
:(.text+0x5d8d4): undefined reference to `i2c_master_send'
This can happen if a audio driver that is using the regmap SigmaDSP interface is
built into the kernel, but core I2C support is build as a module. To fix this
split the SigmaDSP module into three modules, one module providing the core
infrastructure and two small modules implementing the regmap and I2C interfaces.
This allows e.g. the core infrastructure and regmap support to be built into the
kernel while I2C support can still be build as a module.
Fixes: dab464b60 ("ASoC: Add ADAU1361/ADAU1761 audio CODEC support")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>
Mark Brown