Currently if vxlan tunnel ipv6 src isn't supplied the driver fails to
resolve it as part of the route lookup. The resulting encap header
is left with a zeroed out ipv6 src address so the packets are sent
with this src ip.
Use an appropriate route lookup API that also resolves the source
ipv6 address if it's not supplied.
Fixes: ce99f6b97f ('net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels')
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Currently, increasing the number of combined channels is changing
the RSS spread to use the new created channels.
Prevent the RSS spread change in case the user explicitly declare it,
to avoid overriding user configuration.
Tested:
when RSS default:
# ethtool -L ens8 combined 4
RSS spread will change and point to 4 channels.
# ethtool -X ens8 equal 4
# ethtool -L ens8 combined 6
RSS will not change after increasing the number of the channels.
Fixes: 8bf3686204 ('ethtool: ensure channel counts are within bounds during SCHANNELS')
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Function mlx5e_dealloc_rx_wqe is using page pointer value as an
indication to valid DMA mapping. In case that the mapping failed, we
released the page but kept the dangling pointer. Store the page pointer
only after the DMA mapping passed to avoid invalid page DMA unmap.
Fixes: bc77b240b3 ("net/mlx5e: Add fragmented memory support for RX multi packet WQE")
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
MLX5_INTERFACE_STATE_SHUTDOWN is not used in the code.
Fixes: 5fc7197d3a ("net/mlx5: Add pci shutdown callback")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
There is an issue where the firmware fails during mlx5_load_one,
the health_care timer detects the issue and schedules a health_care call.
Then the mlx5_load_one detects the issue, cleans up and quits. Then
the health_care starts and calls mlx5_unload_one to clean up the resources
that no longer exist and causes kernel panic.
The root cause is that the bit MLX5_INTERFACE_STATE_DOWN is not set
after mlx5_load_one fails. The solution is removing the bit
MLX5_INTERFACE_STATE_DOWN and quit mlx5_unload_one if the
bit MLX5_INTERFACE_STATE_UP is not set. The bit MLX5_INTERFACE_STATE_DOWN
is redundant and we can use MLX5_INTERFACE_STATE_UP instead.
Fixes: 5fc7197d3a ("net/mlx5: Add pci shutdown callback")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Support for ISSI version 0 was recently broken as the arm_srq_cmd
command, which is used only for ISSI version 0, was given the opcode
for ISSI version 1 instead of ISSI version 0.
Change arm_srq_cmd to use the correct command opcode for ISSI version
0.
Fixes: af1ba291c5 ('{net, IB}/mlx5: Refactor internal SRQ API')
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Current code doesn't report DCB_CAP_DCBX_HOST capability when query
through getcap. User space lldptool expects capability to have HOST mode
set when it wants to configure DCBX CEE mode. In absence of HOST mode
capability, lldptool fails to switch to CEE mode.
This fix returns DCB_CAP_DCBX_HOST capability when port's DCBX
controlled mode is under software control.
Fixes: 3a6a931dfb ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
qos capability is the master capability bit that determines
if the DCBX is supported for the PCI function. If this bit is off,
driver cannot run any dcbx code.
Fixes: e207b7e991 ("net/mlx5e: ConnectX-4 firmware support for DCBX")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Florian Westphal says:
====================
tcp: re-add header prediction
Eric reported a performance regression caused by header prediction
removal.
We now call tcp_ack() much more frequently, for some workloads
this brings in enough cache line misses to become noticeable.
We could possibly still kill HP provided we find a different
way to suppress unneeded tcp_ack, but given we're late in
the cycle it seems preferable to revert.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit 45f119bf93.
Eric Dumazet says:
We found at Google a significant regression caused by
45f119bf93 tcp: remove header prediction
In typical RPC (TCP_RR), when a TCP socket receives data, we now call
tcp_ack() while we used to not call it.
This touches enough cache lines to cause a slowdown.
so problem does not seem to be HP removal itself but the tcp_ack()
call. Therefore, it might be possible to remove HP after all, provided
one finds a way to elide tcp_ack for most cases.
Reported-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change was a followup to the header prediction removal,
so first revert this as a prerequisite to back out hp removal.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
snd_soc_of_parse_card_name() doesn't return an error if the requested
property isn't present, but silently fails to fill the card name. This can
not be changed, as it is a backwards compatibility measure itself.
We can not rely on the return value of this function alone, but must check
if the card name has been filled sucessfully when deciding to skip the
fallback path, which is in place for existing users.
Fixes: dedfaa1eed (ASoC: simple-card-utils: enable "label" on
asoc_simple_card_parse_card_name)
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
When moving the IRDA code out of net/ into drivers/staging/irda/net, the
link order changes when IRDA is built into the kernel. That causes a
kernel crash at boot time as netfilter isn't initialized yet.
To fix this, move the init call level of the irda core to be
device_initcall() as the link order keeps this being initialized at the
correct time.
Reported-by: kernel test robot <fengguang.wu@intel.com>
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
It is quite common for ti_cm_get_macid() to fail on some of the
platforms it is invoked on. They include any platform where
mac address is not part of SoC register space.
On these platforms, mac address is read and populated in
device-tree by bootloader. An example is TI DA850.
Downgrade the severity of message to "information", so it does
not spam logs when 'quiet' boot is desired.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
calling memcpy immediately after memset with the same region of memory
makes memset redundant.
Signed-off-by: Himanshu Jha <himanshujha199640@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Since commit 41977e86c9 ("rt2x00: add support for MT7620") we do not
initialize TX_PIN_CFG setting. This cause breakage at least on some
RT3573 devices. To fix the problem patch restores previous behaviour
for non MT7620 chips.
Fixes: 41977e86c9 ("rt2x00: add support for MT7620")
Bugzilla: https://bugzilla.redhat.com/show_bug.cgi?id=1480829
Reported-and-tested-by: Jussi Eloranta <jussi.eloranta@csun.edu>
Cc: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Acked-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
There is a missing unlock if rsi_find_sta() fails in
rsi_mac80211_ampdu_action() or if we hit the -EINVAL path in
rsi_mac80211_sta_add().
Fixes: 3528608f3a ("rsi: handle station connection in AP mode")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
* Fix a queue hang problem due to 11w behavior
* Fix a warning caused by a too long debug print
* Bump API number to the latest version we support
-----BEGIN PGP SIGNATURE-----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=byLy
-----END PGP SIGNATURE-----
Merge tag 'iwlwifi-next-for-kalle-2017-08-30' of git://git.kernel.org/pub/scm/linux/kernel/git/iwlwifi/iwlwifi-next
Last set of iwlwifi patches for 4.14
* Fix a queue hang problem due to 11w behavior
* Fix a warning caused by a too long debug print
* Bump API number to the latest version we support
Pull NVMe fixes from Christoph:
"Three more fixes for 4.13 below:
- fix the incorrect bit for the doorbell buffer features (Changpeng Liu)
- always use a 4k MR page size for RDMA, to not get in trouble with
offset in non-4k page size systems (no-op for x86) (Max Gurtovoy)
- and a fix for the new nvme host memory buffer support to keep the
descriptor list DMA mapped when the buffer is enabled (me)"
PCM OSS emulation issues the drain ioctl without power lock. It used
to work in the earlier kernels as the power lock was taken inside
snd_pcm_drain() itself. But since 68b4acd322 ("ALSA: pcm: Apply
power lock globally to common ioctls"), the power lock is taken
outside the function. Due to that change, the call via OSS emulation
leads to the unbalanced power lock, thus it deadlocks.
As a quick fix, just take the power lock before snd_pcm_drain() call
for OSS emulation path. A better cleanup will follow later.
Fixes: 68b4acd322 ("ALSA: pcm: Apply power lock globally to common ioctls")
Reported-and-tested-by: Markus Trippelsdorf <markus@trippelsdorf.de>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
NVMe 1.3 specification defines the Optional Admin Command Support feature
flags, bit 8 set to '1' then the controller supports the Doorbell Buffer
Config command. Bit 7 is used for Virtualization Mangement command.
Signed-off-by: Changpeng Liu <changpeng.liu@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Fixes: f9f38e33 ("nvme: improve performance for virtual NVMe devices")
Cc: stable@vger.kernel.org
The NVMe 1.3 specification says in section 5.21.1.13:
"After a successful completion of a Set Features enabling the host memory
buffer, the host shall not write to the associated host memory region,
buffer size, or descriptor list until the host memory buffer has been
disabled."
While this doesn't state that the descriptor list must remain accessible
to the device it certainly implies it must remaing readable by the device.
So switch to a dma coherent allocation for the descriptor list just to be
safe - it's not like the cost for it matters compared to the actual
memory buffers.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Keith Busch <keith.busch@intel.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Fixes: 87ad72a59a ("nvme-pci: implement host memory buffer support")
Due to various page sizes in the system (IOMMU/device/kernel), we
set the fabrics controller page size to 4k and block layer boundaries
accordinglly. In architectures that uses different kernel page size
we'll have a mismatch to the MR page size that may cause a mapping error.
Update the MR page size to correspond to the core ctrl settings.
Signed-off-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Sagi Grimberg <sagi@grimberg.me>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Xenon sdh controller requests proper SD bus voltage select
bits programmed even with vmmc power supply. Any reserved
value(100b-000b) programmed in this field will lead to controller
ignore SD bus power bit and keep its value at zero.
Add set_power callback to handle this.
Signed-off-by: Zhoujie Wu <zjwu@marvell.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Fixes: 3a3748dba8 ("mmc: sdhci-xenon: Add Marvell Xenon SDHC core functionality")
Cc: <stable@vger.kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Commit 2a842acab1 ("block: introduce new block status code type") changed
the error type but not in patches merged through the mmc tree, like
commit 0493f6fe5b ("mmc: block: Move boot partition locking into a driver
op"). Fix one error code that is incorrect and also use BLK_STS_OK in
preference to 0.
Fixes: 17ece345a0 ("Merge tag 'mmc-v4.13' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc")
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
These devices support -34.ucode, so load it.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Use bcast station for all non bufferable frames on AP and AD-HOC.
The host is no longer aware of STAs PS status because of buffer
station offload, so we can't rely on mac80211 to toggle on
IEEE80211_TX_CTL_NO_PS_BUFFER bit.
A possible issue with buffering such frames, beside the obvious spec
violation, is when a station disconnects while in PS but the AP isn't
aware of that. In such scenarios the AP won't be able to send probe
responses or auth frames so the STA won't be able to reconnect and
the AP will have a queue hang.
Fixes: 3e56eadfb6 ("iwlwifi: mvm: implement AP/GO uAPSD support")
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
There is a debug print that sometimes reaches over
110 chars, thus generating a warning in those cases.
Split the print into two to prevent these cases.
Fixes: 92b0f7b26b ("iwlwifi: split the regulatory rules when the bandwidth flags require it")
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
A stray return was added in the macro bcmgenet_##name##_writel where it
should not, drop it.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Fixes: 69d2ea9c79 ("net: bcmgenet: Use correct I/O accessors")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The phy is connected at early stage of probe but not properly
disconnected if error occurs. This patch fixes the issue.
Also changing the return type of xgene_enet_check_phy_handle(),
since this function always returns success.
Signed-off-by: Quan Nguyen <qnguyen@apm.com>
Signed-off-by: Iyappan Subramanian <isubramanian@apm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Florian reported UDP xmit drops that could be root caused to the
too small neigh limit.
Current limit is 64 KB, meaning that even a single UDP socket would hit
it, since its default sk_sndbuf comes from net.core.wmem_default
(~212992 bytes on 64bit arches).
Once ARP/ND resolution is in progress, we should allow a little more
packets to be queued, at least for one producer.
Once neigh arp_queue is filled, a rogue socket should hit its sk_sndbuf
limit and either block in sendmsg() or return -EAGAIN.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Since the removal of NET_DMA, dmaengine.h header file shouldn't be needed
by netdevice.h anymore.
Signed-off-by: Dave Jiang <dave.jiang@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The GENET driver currently uses __raw_{read,write}l which means
native I/O endian. This works correctly for an ARM LE kernel (default)
but fails miserably on an ARM BE (BE8) kernel where registers are kept
little endian, so replace uses with {read,write}l_relaxed here which is
what we want because this is all performance sensitive code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Weilin Chang <weilin.chang@cavium.com>
Signed-off-by: Felix Manlunas <felix.manlunas@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Both the nfp_net_pf_app_start() and the nfp_net_pci_probe() functions
call nfp_net_pf_app_stop_ctrl(pf) so there is a double free. The free
should be done from the probe function because it's allocated there so
I have removed the call from nfp_net_pf_app_start().
Fixes: 02082701b9 ("nfp: create control vNICs and wire up rx/tx")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Make these const as they are not modified anywhere.
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is a difference in the bit position of the normal interrupt summary
enable (NIE) and abnormal interrupt summary enable (AIE) between revisions
of the hardware. For older revisions the NIE and AIE bits are positions
16 and 15 respectively. For newer revisions the NIE and AIE bits are
positions 15 and 14. The effect in changing the bit position is that
newer hardware won't receive AIE interrupts in the current version of the
driver. Specifically, the driver uses this interrupt to collect
statistics on when a receive buffer unavailable event occurs and to
restart the driver/device when a fatal bus error occurs.
Update the driver to set the interrupt enable bit based on the reported
version of the hardware.
Signed-off-by: Tom Lendacky <thomas.lendacky@amd.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Jiri Benc says:
====================
nsh: headers, GSO
This adds header structs and helpers for NSH together with GSO support.
Note there is no code in this patchset that actually manipulates the NSH
headers. That was sent to netdev by Yi Yang ("[PATCH net-next v6 0/3]
openvswitch: add NSH support"). The aim of this series is to lay the
groundwork and ease the implementation for him.
In addition to openvswitch, the NSH support should be added to tc (flower to
match, act_nsh to push/pop NSH headers). That will come later. There's
currently no plan to support NSH by other means than those two.
The patch 3 in this patchset was written by Yi Yang, I took it from the
aforementioned series and slightly modified it - see the note in the patch.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Add a new nsh/ directory. It currently holds only GSO functions but more
will come: in particular, code shared by openvswitch and tc to manipulate
NSH headers.
For now, assume there's no hardware support for NSH segmentation. We can
always introduce netdev->nsh_features later.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
NSH (Network Service Header)[1] is a new protocol for service
function chaining, it can be handled as a L3 protocol like
IPv4 and IPv6, Eth + NSH + Inner packet or VxLAN-gpe + NSH +
Inner packet are two typical use cases.
This patch adds NSH header structures and helpers for NSH GSO
support and Open vSwitch NSH support.
[1] https://datatracker.ietf.org/doc/draft-ietf-sfc-nsh/
[Jiri: added nsh_hdr() helper and renamed the header struct to "struct
nshhdr" to match the usual pattern. Removed packet type defines, these are
now shared with VXLAN-GPE.]
Signed-off-by: Yi Yang <yi.y.yang@intel.com>
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The values are shared between VXLAN-GPE and NSH. Originally probably by
coincidence but I notified both working groups about this last year and they
seem to keep the values in sync since then.
Hopefully they'll get a single IANA registry for the values, too. (I asked
them for that.)
Factor out the code to be shared by the NSH implementation.
NSH and MPLS values are added in this patch, too. For MPLS, the drafts
incorrectly assign only a single value, while we have two MPLS ethertypes.
I raised the problem with both groups. For now, I assume the value is for
unicast.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The NSH draft says:
An IEEE EtherType, 0x894F, has been allocated for NSH.
Signed-off-by: Jiri Benc <jbenc@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Alexander Aring says:
====================
tc: act_ife: handle IEEE IFE ethertype as default
this patch series will introduce the IFE ethertype which is registered by
IEEE. If the netlink act_ife type netlink attribute is not given it will
use this value by default now.
At least it will introduce some UAPI testcases to check if the default type
is used if not specified and vice versa.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a new testcase for the IFE type setting in tc. In case
of user specified the type it will check if the ife is correctly
configured to react on it. If it's not specified the default IFE type
should be used.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch handles a default IFE type if it's not given by user space
netlink api. The default IFE type will be the registered ethertype by
IEEE for IFE ForCES.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the forces IFE lfb type according to IEEE registered
ethertypes. See http://standards-oui.ieee.org/ethertype/eth.txt for more
information. Since there exists the IFE subsystem it can be used there.
This patch also use the correct word "ForCES" instead of "FoRCES" which
is a spelling error inside the IEEE ethertype specification.
Signed-off-by: Alexander Aring <aring@mojatatu.com>
Acked-by: Jamal Hadi Salim <jhs@mojatatu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Explain that the patch queue in patchwork should not be touched by patch
submitters.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Paul Blakey