Pass in the SKB rather than just the IP addresses, so that policy
and other aspects can reside in ip_rt_redirect() rather then
icmp_redirect().
Signed-off-by: David S. Miller <davem@davemloft.net>
This introduce TSQ (TCP Small Queues)
TSQ goal is to reduce number of TCP packets in xmit queues (qdisc &
device queues), to reduce RTT and cwnd bias, part of the bufferbloat
problem.
sk->sk_wmem_alloc not allowed to grow above a given limit,
allowing no more than ~128KB [1] per tcp socket in qdisc/dev layers at a
given time.
TSO packets are sized/capped to half the limit, so that we have two
TSO packets in flight, allowing better bandwidth use.
As a side effect, setting the limit to 40000 automatically reduces the
standard gso max limit (65536) to 40000/2 : It can help to reduce
latencies of high prio packets, having smaller TSO packets.
This means we divert sock_wfree() to a tcp_wfree() handler, to
queue/send following frames when skb_orphan() [2] is called for the
already queued skbs.
Results on my dev machines (tg3/ixgbe nics) are really impressive,
using standard pfifo_fast, and with or without TSO/GSO.
Without reduction of nominal bandwidth, we have reduction of buffering
per bulk sender :
< 1ms on Gbit (instead of 50ms with TSO)
< 8ms on 100Mbit (instead of 132 ms)
I no longer have 4 MBytes backlogged in qdisc by a single netperf
session, and both side socket autotuning no longer use 4 Mbytes.
As skb destructor cannot restart xmit itself ( as qdisc lock might be
taken at this point ), we delegate the work to a tasklet. We use one
tasklest per cpu for performance reasons.
If tasklet finds a socket owned by the user, it sets TSQ_OWNED flag.
This flag is tested in a new protocol method called from release_sock(),
to eventually send new segments.
[1] New /proc/sys/net/ipv4/tcp_limit_output_bytes tunable
[2] skb_orphan() is usually called at TX completion time,
but some drivers call it in their start_xmit() handler.
These drivers should at least use BQL, or else a single TCP
session can still fill the whole NIC TX ring, since TSQ will
have no effect.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Dave Taht <dave.taht@bufferbloat.net>
Cc: Tom Herbert <therbert@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Nandita Dukkipati <nanditad@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The recent patch "tcp: Maintain dynamic metrics in local cache." introduced
an out of bounds access due to what appears to be a typo. I believe this
change should resolve the issue by replacing the access to RTAX_CWND with
TCP_METRIC_CWND.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix incorrect start markers, wrapped summary lines, missing section
breaks, incorrect separators, and some name mismatches.
Signed-off-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Nothing every writes to ipv4 metrics any longer.
PMTU is stored in rt->rt_pmtu.
Dynamic TCP metrics are stored in a special TCP metrics cache,
completely outside of the routes.
Therefore ->cow_metrics() can simply nothing more than a WARN_ON
trigger so we can catch anyone who tries to add new writes to
ipv4 route metrics.
Signed-off-by: David S. Miller <davem@davemloft.net>
Blackhole routes have a COW metrics operation that returns NULL
always, therefore this dst_copy_metrics() call did absolutely
nothing.
Signed-off-by: David S. Miller <davem@davemloft.net>
No longer needed. TCP writes metrics, but now in it's own special
cache that does not dirty the route metrics. Therefore there is no
longer any reason to pre-cow metrics in this way.
Signed-off-by: David S. Miller <davem@davemloft.net>
We don't maintain it dynamically any longer, so reporting it would
be extremely misleading. Report zero instead.
Signed-off-by: David S. Miller <davem@davemloft.net>
Maintain a local hash table of TCP dynamic metrics blobs.
Computed TCP metrics are no longer maintained in the route metrics.
The table uses RCU and an extremely simple hash so that it has low
latency and low overhead. A simple hash is legitimate because we only
make metrics blobs for fully established connections.
Some tweaking of the default hash table sizes, metric timeouts, and
the hash chain length limit certainly could use some tweaking. But
the basic design seems sound.
With help from Eric Dumazet and Joe Perches.
Signed-off-by: David S. Miller <davem@davemloft.net>
If the user hasn't actually installed any custom rules, or fiddled
with the default ones, don't go through the whole FIB rules layer.
It's just pure overhead.
Instead do what we do with CONFIG_IP_MULTIPLE_TABLES disabled, check
the individual tables by hand, one by one.
Also, move fib_num_tclassid_users into the ipv4 network namespace.
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_options_compile() can avoid calling fib_compute_spec_dst()
by default, and perform the call only if needed.
David suggested to add a helper to make the call only once.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Causes the handler to use the daddr in the ipv4/ipv6 header when
the route gateway is unspecified (local subnet).
Signed-off-by: David S. Miller <davem@davemloft.net>
When a dst_confirm() happens, mark the confirmation as pending in the
dst. Then on the next packet out, when we have the neigh in-hand, do
the update.
This removes the dependency in dst_confirm() of dst's having an
attached neigh.
While we're here, remove the explicit 'dst' NULL check, all except 2
or 3 call sites ensure it's not NULL. So just fix those cases up.
Signed-off-by: David S. Miller <davem@davemloft.net>
Soon routes will not have a cached neigh attached, nor will we
be able to necessarily go directly to a neigh from an arbitrary
route.
Signed-off-by: David S. Miller <davem@davemloft.net>
The spec_dst uses should be guarded by skb_rtable() being non-NULL
not just the SKB being non-null.
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch generalizes nf_ct_l4proto_net by splitting it into chunks and
moving the corresponding protocol part to where it really belongs to.
To clarify, note that we follow two different approaches to support per-net
depending if it's built-in or run-time loadable protocol tracker.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Acked-by: Gao feng <gaofeng@cn.fujitsu.com>
This patch adds the following structure:
struct netlink_kernel_cfg {
unsigned int groups;
void (*input)(struct sk_buff *skb);
struct mutex *cb_mutex;
};
That can be passed to netlink_kernel_create to set optional configurations
for netlink kernel sockets.
I've populated this structure by looking for NULL and zero parameters at the
existing code. The remaining parameters that always need to be set are still
left in the original interface.
That includes optional parameters for the netlink socket creation. This allows
easy extensibility of this interface in the future.
This patch also adapts all callers to use this new interface.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
If rpfilter is off (or the SKB has an IPSEC path) and there are not
tclassid users, we don't have to do anything at all when
fib_validate_source() is invoked besides setting the itag to zero.
We monitor tclassid uses with a counter (modified only under RTNL and
marked __read_mostly) and we protect the fib_validate_source() real
work with a test against this counter and whether rpfilter is to be
done.
Having a way to know whether we need no tclassid processing or not
also opens the door for future optimized rpfilter algorithms that do
not perform full FIB lookups.
Signed-off-by: David S. Miller <davem@davemloft.net>
Checking for in_dev being NULL is pointless.
In fact, all of our callers have in_dev precomputed already,
so just pass it in and remove the NULL checking.
Signed-off-by: David S. Miller <davem@davemloft.net>
Based upon feedback from Julian Anastasov.
1) Use route flags to determine multicast/broadcast, not the
packet flags.
2) Leave saddr unspecified in flow key.
3) Adjust how we invoke inet_select_addr(). Pass ip_hdr(skb)->saddr as
second arg, and if it was zeronet use link scope.
4) Use loopback as input interface in flow key.
Signed-off-by: David S. Miller <davem@davemloft.net>
The specific destination is the host we direct unicast replies to.
Usually this is the original packet source address, but if we are
responding to a multicast or broadcast packet we have to use something
different.
Specifically we must use the source address we would use if we were to
send a packet to the unicast source of the original packet.
The routing cache precomputes this value, but we want to remove that
precomputation because it creates a hard dependency on the expensive
rpfilter source address validation which we'd like to make cheaper.
There are only three places where this matters:
1) ICMP replies.
2) pktinfo CMSG
3) IP options
Now there will be no real users of rt->rt_spec_dst and we can simply
remove it altogether.
Signed-off-by: David S. Miller <davem@davemloft.net>
Rename it to ip_send_unicast_reply() and add explicit 'saddr'
argument.
This removed one of the few users of rt->rt_spec_dst.
Signed-off-by: David S. Miller <davem@davemloft.net>
This reverts commit c074da2810.
This change has several unwanted side effects:
1) Sockets will cache the DST_NOCACHE route in sk->sk_rx_dst and we'll
thus never create a real cached route.
2) All TCP traffic will use DST_NOCACHE and never use the routing
cache at all.
Signed-off-by: David S. Miller <davem@davemloft.net>
dropwatch wrongly diagnose all received UDP packets as drops.
This patch removes trace_kfree_skb() done in skb_free_datagram_locked().
Locations calling skb_free_datagram_locked() should do it on their own.
As a result, drops are accounted on the right function.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also fix a needless skb tailroom check for a 4 bytes area
after after each rtnexthop block.
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
Also, no need to trim on nlmsg_put() failure, nothing has been added
yet. We also want to use nlmsg_end(), nlmsg_new() and nlmsg_free().
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
DDOS synflood attacks hit badly IP route cache.
On typical machines, this cache is allowed to hold up to 8 Millions dst
entries, 256 bytes for each, for a total of 2GB of memory.
rt_garbage_collect() triggers and tries to cleanup things.
Eventually route cache is disabled but machine is under fire and might
OOM and crash.
This patch exploits the new TCP early demux, to set a nocache
boolean in case incoming TCP frame is for a not yet ESTABLISHED or
TIMEWAIT socket.
This 'nocache' boolean is then used in case dst entry is not found in
route cache, to create an unhashed dst entry (DST_NOCACHE)
SYN-cookie-ACK sent use a similar mechanism (ipv4: tcp: dont cache
output dst for syncookies), so after this patch, a machine is able to
absorb a DDOS synflood attack without polluting its IP route cache.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Split sysctl function into smaller chucks to cleanup code and prepare
patches to reduce ifdef pollution.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
l4proto->init contain quite redundant code. We can simplify this
by adding a new parameter l3proto.
This patch prepares that code simplification.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
And account for the fact that, when we are not forwarding, we should
bump statistic counters rather than emit an ICMP response.
RP-filter rejected lookups are still not cached.
Since -EHOSTUNREACH and -ENETUNREACH can now no longer be seen in
ip_rcv_finish(), remove those checks.
Signed-off-by: David S. Miller <davem@davemloft.net>
IPv4 routing cache entries no longer use dst->expires, because the
metrics, PMTU, and redirect information are stored in the inetpeer
cache.
Signed-off-by: David S. Miller <davem@davemloft.net>
The dest port for the call to __inet_lookup_established() in TCP early demux
code is passed with the wrong endian-ness. This causes the lookup to fail
leading to early demux not being used.
Signed-off-by: Vijay Subramanian <subramanian.vijay@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo says:
====================
The following four patches provide Netfilter fixes for the cthelper
infrastructure that was recently merged mainstream, they are:
* two fixes for compilation breakage with two different configurations:
- CONFIG_NF_NAT=m and CONFIG_NF_CT_NETLINK=y
- NF_CONNTRACK_EVENTS=n and CONFIG_NETFILTER_NETLINK_QUEUE_CT=y
* two fixes for sparse warnings.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't cache output dst for syncookies, as this adds pressure on IP route
cache and rcu subsystem for no gain.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hans Schillstrom <hans.schillstrom@ericsson.com>
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant to add a control for disabling early socket demux.
The main motivation behind this patch is to provide an option to disable
the feature as it adds an additional cost to routing that reduces overall
throughput by up to 5%. For example one of my systems went from 12.1Mpps
to 11.6 after the early socket demux was added. It looks like the reason
for the regression is that we are now having to perform two lookups, first
the one for an established socket, and then the one for the routing table.
By adding this patch and toggling the value for ip_early_demux to 0 I am
able to get back to the 12.1Mpps I was previously seeing.
[ Move local variables in ip_rcv_finish() down into the basic
block in which they are actually used. -DaveM ]
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
LD init/built-in.o
net/built-in.o:(.data+0x4408): undefined reference to `nf_nat_tcp_seq_adjust'
make: *** [vmlinux] Error 1
This patch adds a new pointer hook (nfq_ct_nat_hook) similar to other existing
in Netfilter to solve our complicated configuration dependencies.
Reported-by: Valdis Kletnieks <valdis.kletnieks@vt.edu>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
No need to use cmpxchg() in inetpeer_invalidate_tree() since we hold
base lock.
Also use correct rcu annotations to remove sparse errors
(CONFIG_SPARSE_RCU_POINTER=y)
net/ipv4/inetpeer.c:144:19: error: incompatible types in comparison
expression (different address spaces)
net/ipv4/inetpeer.c:149:20: error: incompatible types in comparison
expression (different address spaces)
net/ipv4/inetpeer.c:595:10: error: incompatible types in comparison
expression (different address spaces)
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Input packet processing for local sockets involves two major demuxes.
One for the route and one for the socket.
But we can optimize this down to one demux for certain kinds of local
sockets.
Currently we only do this for established TCP sockets, but it could
at least in theory be expanded to other kinds of connections.
If a TCP socket is established then it's identity is fully specified.
This means that whatever input route was used during the three-way
handshake must work equally well for the rest of the connection since
the keys will not change.
Once we move to established state, we cache the receive packet's input
route to use later.
Like the existing cached route in sk->sk_dst_cache used for output
packets, we have to check for route invalidations using dst->obsolete
and dst->ops->check().
Early demux occurs outside of a socket locked section, so when a route
invalidation occurs we defer the fixup of sk->sk_rx_dst until we are
actually inside of established state packet processing and thus have
the socket locked.
Signed-off-by: David S. Miller <davem@davemloft.net>
Don't pretend that inet_protos[] and inet6_protos[] are hashes, thay
are just a straight arrays. Remove all unnecessary hash masking.
Document MAX_INET_PROTOS.
Use RAW_HTABLE_SIZE when appropriate.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It makes no sense to execute this limit test every time we create a
routing cache entry.
We can't simply error out on these things since we've silently
accepted and truncated them forever.
Signed-off-by: David S. Miller <davem@davemloft.net>
Pablo says:
====================
This is the second batch of Netfilter updates for net-next. It contains the
kernel changes for the new user-space connection tracking helper
infrastructure.
More details on this infrastructure are provides here:
http://lwn.net/Articles/500196/
Still, I plan to provide some official documentation through the
conntrack-tools user manual on how to setup user-space utilities for this.
So far, it provides two helper in user-space, one for NFSv3 and another for
Oracle/SQLnet/TNS. Yet in my TODO list.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
There are good reasons to supports helpers in user-space instead:
* Rapid connection tracking helper development, as developing code
in user-space is usually faster.
* Reliability: A buggy helper does not crash the kernel. Moreover,
we can monitor the helper process and restart it in case of problems.
* Security: Avoid complex string matching and mangling in kernel-space
running in privileged mode. Going further, we can even think about
running user-space helpers as a non-root process.
* Extensibility: It allows the development of very specific helpers (most
likely non-standard proprietary protocols) that are very likely not to be
accepted for mainline inclusion in the form of kernel-space connection
tracking helpers.
This patch adds the infrastructure to allow the implementation of
user-space conntrack helpers by means of the new nfnetlink subsystem
`nfnetlink_cthelper' and the existing queueing infrastructure
(nfnetlink_queue).
I had to add the new hook NF_IP6_PRI_CONNTRACK_HELPER to register
ipv[4|6]_helper which results from splitting ipv[4|6]_confirm into
two pieces. This change is required not to break NAT sequence
adjustment and conntrack confirmation for traffic that is enqueued
to our user-space conntrack helpers.
Basic operation, in a few steps:
1) Register user-space helper by means of `nfct':
nfct helper add ftp inet tcp
[ It must be a valid existing helper supported by conntrack-tools ]
2) Add rules to enable the FTP user-space helper which is
used to track traffic going to TCP port 21.
For locally generated packets:
iptables -I OUTPUT -t raw -p tcp --dport 21 -j CT --helper ftp
For non-locally generated packets:
iptables -I PREROUTING -t raw -p tcp --dport 21 -j CT --helper ftp
3) Run the test conntrackd in helper mode (see example files under
doc/helper/conntrackd.conf
conntrackd
4) Generate FTP traffic going, if everything is OK, then conntrackd
should create expectations (you can check that with `conntrack':
conntrack -E expect
[NEW] 301 proto=6 src=192.168.1.136 dst=130.89.148.12 sport=0 dport=54037 mask-src=255.255.255.255 mask-dst=255.255.255.255 sport=0 dport=65535 master-src=192.168.1.136 master-dst=130.89.148.12 sport=57127 dport=21 class=0 helper=ftp
[DESTROY] 301 proto=6 src=192.168.1.136 dst=130.89.148.12 sport=0 dport=54037 mask-src=255.255.255.255 mask-dst=255.255.255.255 sport=0 dport=65535 master-src=192.168.1.136 master-dst=130.89.148.12 sport=57127 dport=21 class=0 helper=ftp
This confirms that our test helper is receiving packets including the
conntrack information, and adding expectations in kernel-space.
The user-space helper can also store its private tracking information
in the conntrack structure in the kernel via the CTA_HELP_INFO. The
kernel will consider this a binary blob whose layout is unknown. This
information will be included in the information that is transfered
to user-space via glue code that integrates nfnetlink_queue and
ctnetlink.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
User-space programs that receive traffic via NFQUEUE may mangle packets.
If NAT is enabled, this usually puzzles sequence tracking, leading to
traffic disruptions.
With this patch, nfnl_queue will make the corresponding NAT TCP sequence
adjustment if:
1) The packet has been mangled,
2) the NFQA_CFG_F_CONNTRACK flag has been set, and
3) NAT is detected.
There are some records on the Internet complaning about this issue:
http://stackoverflow.com/questions/260757/packet-mangling-utilities-besides-iptables
By now, we only support TCP since we have no helpers for DCCP or SCTP.
Better to add this if we ever have some helper over those layer 4 protocols.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch uses the new variable length conntrack extensions.
Instead of using union nf_conntrack_help that contain all the
helper private data information, we allocate variable length
area to store the private helper data.
This patch includes the modification of all existing helpers.
It also includes a couple of include header to avoid compilation
warnings.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
With ip_rt_frag_needed() removed, we have to explicitly update PMTU
information in every ICMP error handler.
Create two helper functions to facilitate this.
1) ipv4_sk_update_pmtu()
This updates the PMTU when we have a socket context to
work with.
2) ipv4_update_pmtu()
Raw version, used when no socket context is available. For this
interface, we essentially just pass in explicit arguments for
the flow identity information we would have extracted from the
socket.
And you'll notice that ipv4_sk_update_pmtu() is simply implemented
in terms of ipv4_update_pmtu()
Note that __ip_route_output_key() is used, rather than something like
ip_route_output_flow() or ip_route_output_key(). This is because we
absolutely do not want to end up with a route that does IPSEC
encapsulation and the like. Instead, we only want the route that
would get us to the node described by the outermost IP header.
Reported-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Conflicts:
MAINTAINERS
drivers/net/wireless/iwlwifi/pcie/trans.c
The iwlwifi conflict was resolved by keeping the code added
in 'net' that turns off the buggy chip feature.
The MAINTAINERS conflict was merely overlapping changes, one
change updated all the wireless web site URLs and the other
changed some GIT trees to be Johannes's instead of John's.
Signed-off-by: David S. Miller <davem@davemloft.net>
Add dev_loopback_xmit() in order to deduplicate functions
ip_dev_loopback_xmit() (in net/ipv4/ip_output.c) and
ip6_dev_loopback_xmit() (in net/ipv6/ip6_output.c).
I was about to reinvent the wheel when I noticed that
ip_dev_loopback_xmit() and ip6_dev_loopback_xmit() do exactly what I
need and are not IP-only functions, but they were not available to reuse
elsewhere.
ip6_dev_loopback_xmit() does not have line "skb_dst_force(skb);", but I
understand that this is harmless, and should be in dev_loopback_xmit().
Signed-off-by: Michel Machado <michel@digirati.com.br>
CC: "David S. Miller" <davem@davemloft.net>
CC: Alexey Kuznetsov <kuznet@ms2.inr.ac.ru>
CC: James Morris <jmorris@namei.org>
CC: Hideaki YOSHIFUJI <yoshfuji@linux-ipv6.org>
CC: Patrick McHardy <kaber@trash.net>
CC: Eric Dumazet <edumazet@google.com>
CC: Jiri Pirko <jpirko@redhat.com>
CC: "Michał Mirosław" <mirq-linux@rere.qmqm.pl>
CC: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Routing of 127/8 is tradtionally forbidden, we consider
packets from that address block martian when routing and do
not process corresponding ARP requests.
This is a sane default but renders a huge address space
practically unuseable.
The RFC states that no address within the 127/8 block should
ever appear on any network anywhere but it does not forbid
the use of such addresses outside of the loopback device in
particular. For example to address a pool of virtual guests
behind a load balancer.
This patch adds a new interface option 'route_localnet'
enabling routing of the 127/8 address block and processing
of ARP requests on a specific interface.
Note that for the feature to work, the default local route
covering 127/8 dev lo needs to be removed.
Example:
$ sysctl -w net.ipv4.conf.eth0.route_localnet=1
$ ip route del 127.0.0.0/8 dev lo table local
$ ip addr add 127.1.0.1/16 dev eth0
$ ip route flush cache
V2: Fix invalid check to auto flush cache (thanks davem)
Signed-off-by: Thomas Graf <tgraf@suug.ch>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We handle NULL in rt{,6}_set_peer but then our caller will try to pass
that NULL pointer into inet_putpeer() which isn't ready for it.
Fix this by moving the NULL check one level up, and then remove the
now unnecessary NULL check from inetpeer_ptr_set_peer().
Reported-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This implementation can deal with having many inetpeer roots, which is
a necessary prerequisite for per-FIB table rooted peer tables.
Each family (AF_INET, AF_INET6) has a sequence number which we bump
when we get a family invalidation request.
Each peer lookup cheaply checks whether the flush sequence of the
root we are using is out of date, and if so flushes it and updates
the sequence number.
Signed-off-by: David S. Miller <davem@davemloft.net>
There is zero point to this function.
It's only real substance is to perform an extremely outdated BSD4.2
ICMP check, which we can safely remove. If you really have a MTU
limited link being routed by a BSD4.2 derived system, here's a nickel
go buy yourself a real router.
The other actions of ip_rt_frag_needed(), checking and conditionally
updating the peer, are done by the per-protocol handlers of the ICMP
event.
TCP, UDP, et al. have a handler which will receive this event and
transmit it back into the associated route via dst_ops->update_pmtu().
This simplification is important, because it eliminates the one place
where we do not have a proper route context in which to make an
inetpeer lookup.
Signed-off-by: David S. Miller <davem@davemloft.net>
We encode the pointer(s) into an unsigned long with one state bit.
The state bit is used so we can store the inetpeer tree root to use
when resolving the peer later.
Later the peer roots will be per-FIB table, and this change works to
facilitate that.
Signed-off-by: David S. Miller <davem@davemloft.net>
We only need one interface for this operation, since we always know
which inetpeer root we want to flush.
Signed-off-by: David S. Miller <davem@davemloft.net>
Since it's guarenteed that we will access the inetpeer if we're trying
to do timewait recycling and TCP options were enabled on the
connection, just cache the peer in the timewait socket.
In the future, inetpeer lookups will be context dependent (per routing
realm), and this helps facilitate that as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
The get_peer method TCP uses is full of special cases that make no
sense accommodating, and it also gets in the way of doing more
reasonable things here.
First of all, if the socket doesn't have a usable cached route, there
is no sense in trying to optimize timewait recycling.
Likewise for the case where we have IP options, such as SRR enabled,
that make the IP header destination address (and thus the destination
address of the route key) differ from that of the connection's
destination address.
Just return a NULL peer in these cases, and thus we're also able to
get rid of the clumsy inetpeer release logic.
Signed-off-by: David S. Miller <davem@davemloft.net>
There's a lot of places that open-code rt{,6}_get_peer() only because
they want to set 'create' to one. So add an rt{,6}_get_peer_create()
for their sake.
There were also a few spots open-coding plain rt{,6}_get_peer() and
those are transformed here as well.
Signed-off-by: David S. Miller <davem@davemloft.net>
add struct net as a parameter of inet_getpeer_v[4,6],
use net to replace &init_net.
and modify some places to provide net for inet_getpeer_v[4,6]
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
now inetpeer doesn't support namespace,the information will
be leaking across namespace.
this patch move the global vars v4_peers and v6_peers to
netns_ipv4 and netns_ipv6 as a field peers.
add struct pernet_operations inetpeer_ops to initial pernet
inetpeer data.
and change family_to_base and inet_getpeer to support namespace.
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
RFC 4293 defines ipIfStatsOutOctets (similar definition for
ipSystemStatsOutOctets):
The total number of octets in IP datagrams delivered to the lower
layers for transmission. Octets from datagrams counted in
ipIfStatsOutTransmits MUST be counted here.
And ipIfStatsOutTransmits:
The total number of IP datagrams that this entity supplied to the
lower layers for transmission. This includes datagrams generated
locally and those forwarded by this entity.
Therefore, IPSTATS_MIB_OUTOCTETS must be incremented when incrementing
IPSTATS_MIB_OUTFORWDATAGRAMS.
IP_UPD_PO_STATS is not used since ipIfStatsOutRequests must not
include forwarded datagrams:
The total number of IP datagrams that local IP user-protocols
(including ICMP) supplied to IP in requests for transmission. Note
that this counter does not include any datagrams counted in
ipIfStatsOutForwDatagrams.
Signed-off-by: Vincent Bernat <bernat@luffy.cx>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch is a cleanup. Use NFPROTO_* for consistency with other
netfilter code.
Signed-off-by: Alban Crequy <alban.crequy@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Vincent Sanders <vincent.sanders@collabora.co.uk>
This patch adds namespace support for cttimeout.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Since the sysctl data for l[3|4]proto now resides in pernet nf_proto_net.
We can now remove this unused fields from struct nf_contrack_l[3,4]proto.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for IPv4 protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch adds namespace support for ICMP protocol tracker.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch prepares the namespace support for layer 3 protocol trackers.
Basically, this modifies the following interfaces:
* nf_ct_l3proto_[un]register_sysctl.
* nf_conntrack_l3proto_[un]register.
We add a new nf_ct_l3proto_net is used to get the pernet data of l3proto.
This adds rhe new struct nf_ip_net that is used to store the sysctl header
and l3proto_ipv4,l4proto_tcp(6),l4proto_udp(6),l4proto_icmp(v6) because the
protos such tcp and tcp6 use the same data,so making nf_ip_net as a field
of netns_ct is the easiest way to manager it.
This patch also adds init_net to struct nf_conntrack_l3proto to initial
the layer 3 protocol pernet data.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
This patch prepares the namespace support for layer 4 protocol trackers.
Basically, this modifies the following interfaces:
* nf_ct_[un]register_sysctl
* nf_conntrack_l4proto_[un]register
to include the namespace parameter. We still use init_net in this patch
to prepare the ground for follow-up patches for each layer 4 protocol
tracker.
We add a new net_id field to struct nf_conntrack_l4proto that is used
to store the pernet_operations id for each layer 4 protocol tracker.
Note that AF_INET6's protocols do not need to do sysctl compat. Thus,
we only register compat sysctl when l4proto.l3proto != AF_INET6.
Acked-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Gao feng <gaofeng@cn.fujitsu.com>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
commit 5faa5df1fa (inetpeer: Invalidate the inetpeer tree along with
the routing cache) added a race :
Before freeing an inetpeer, we must respect a RCU grace period, and make
sure no user will attempt to increase refcnt.
inetpeer_invalidate_tree() waits for a RCU grace period before inserting
inetpeer tree into gc_list and waking the worker. At that time, no
concurrent lookup can find a inetpeer in this tree.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Acked-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Adding casts of objects to the same type is unnecessary
and confusing for a human reader.
For example, this cast:
int y;
int *p = (int *)&y;
I used the coccinelle script below to find and remove these
unnecessary casts. I manually removed the conversions this
script produces of casts with __force and __user.
@@
type T;
T *p;
@@
- (T *)p
+ p
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Remove some dropwatch/drop_monitor false positives.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_make_synack() clones the dst, and callers release it.
We can avoid two atomic operations per SYNACK if tcp_make_synack()
consumes dst instead of cloning it.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There is no value using sock_wmalloc() in tcp_make_synack().
A listener socket only sends SYNACK packets, they are not queued in a
socket queue, only in Qdisc and device layers, so the number of in
flight packets is limited in these layers. We used sock_wmalloc() with
the %force parameter set to 1 to ignore socket limits anyway.
This patch removes two atomic operations per SYNACK packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
While testing how linux behaves on SYNFLOOD attack on multiqueue device
(ixgbe), I found that SYNACK messages were dropped at Qdisc level
because we send them all on a single queue.
Obvious choice is to reflect incoming SYN packet @queue_mapping to
SYNACK packet.
Under stress, my machine could only send 25.000 SYNACK per second (for
200.000 incoming SYN per second). NIC : ixgbe with 16 rx/tx queues.
After patch, not a single SYNACK is dropped.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Hans Schillstrom <hans.schillstrom@ericsson.com>
Cc: Jesper Dangaard Brouer <brouer@redhat.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull networking changes from David S. Miller:
1) Fix IPSEC header length calculation for transport mode in ESP. The
issue is whether to do the calculation before or after alignment.
Fix from Benjamin Poirier.
2) Fix regression in IPV6 IPSEC fragment length calculations, from Gao
Feng. This is another transport vs tunnel mode issue.
3) Handle AF_UNSPEC connect()s properly in L2TP to avoid OOPSes. Fix
from James Chapman.
4) Fix USB ASIX driver's reception of full sized VLAN packets, from
Eric Dumazet.
5) Allow drop monitor (and, more generically, all generic netlink
protocols) to be automatically loaded as a module. From Neil
Horman.
Fix up trivial conflict in Documentation/feature-removal-schedule.txt
due to new entries added next to each other at the end. As usual.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (38 commits)
net/smsc911x: Repair broken failure paths
virtio-net: remove useless disable on freeze
netdevice: Update netif_dbg for CONFIG_DYNAMIC_DEBUG
drop_monitor: Add module alias to enable automatic module loading
genetlink: Build a generic netlink family module alias
net: add MODULE_ALIAS_NET_PF_PROTO_NAME
r6040: Do a Proper deinit at errorpath and also when driver unloads (calling r6040_remove_one)
r6040: disable pci device if the subsequent calls (after pci_enable_device) fails
skb: avoid unnecessary reallocations in __skb_cow
net: sh_eth: fix the rxdesc pointer when rx descriptor empty happens
asix: allow full size 8021Q frames to be received
rds_rdma: don't assume infiniband device is PCI
l2tp: fix oops in L2TP IP sockets for connect() AF_UNSPEC case
mac80211: fix ADDBA declined after suspend with wowlan
wlcore: fix undefined symbols when CONFIG_PM is not defined
mac80211: fix flag check for QoS NOACK frames
ath9k_hw: apply internal regulator settings on AR933x
ath9k_hw: update AR933x initvals to fix issues with high power devices
ath9k: fix a use-after-free-bug when ath_tx_setup_buffer() fails
ath9k: stop rx dma before stopping tx
...
We call the destroy function when a cgroup starts to be removed, such as
by a rmdir event.
However, because of our reference counters, some objects are still
inflight. Right now, we are decrementing the static_keys at destroy()
time, meaning that if we get rid of the last static_key reference, some
objects will still have charges, but the code to properly uncharge them
won't be run.
This becomes a problem specially if it is ever enabled again, because now
new charges will be added to the staled charges making keeping it pretty
much impossible.
We just need to be careful with the static branch activation: since there
is no particular preferred order of their activation, we need to make sure
that we only start using it after all call sites are active. This is
achieved by having a per-memcg flag that is only updated after
static_key_slow_inc() returns. At this time, we are sure all sites are
active.
This is made per-memcg, not global, for a reason: it also has the effect
of making socket accounting more consistent. The first memcg to be
limited will trigger static_key() activation, therefore, accounting. But
all the others will then be accounted no matter what. After this patch,
only limited memcgs will have its sockets accounted.
[akpm@linux-foundation.org: move enum sock_flag_bits into sock.h,
document enum sock_flag_bits,
convert memcg_proto_active() and memcg_proto_activated() to test_bit(),
redo tcp_update_limit() comment to 80 cols]
Signed-off-by: Glauber Costa <glommer@parallels.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Li Zefan <lizefan@huawei.com>
Acked-by: KAMEZAWA Hiroyuki <kamezawa.hiroyu@jp.fujitsu.com>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Michal Hocko <mhocko@suse.cz>
Acked-by: David Miller <davem@davemloft.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Corrects the function that determines the esp payload size. The calculations
done in esp{4,6}_get_mtu() lead to overlength frames in transport mode for
certain mtu values and suboptimal frames for others.
According to what is done, mainly in esp{,6}_output() and tcp_mtu_to_mss(),
net_header_len must be taken into account before doing the alignment
calculation.
Signed-off-by: Benjamin Poirier <bpoirier@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull more networking updates from David Miller:
"Ok, everything from here on out will be bug fixes."
1) One final sync of wireless and bluetooth stuff from John Linville.
These changes have all been in his tree for more than a week, and
therefore have had the necessary -next exposure. John was just away
on a trip and didn't have a change to send the pull request until a
day or two ago.
2) Put back some defines in user exposed header file areas that were
removed during the tokenring purge. From Stephen Hemminger and Paul
Gortmaker.
3) A bug fix for UDP hash table allocation got lost in the pile due to
one of those "you got it.. no I've got it.." situations. :-)
From Tim Bird.
4) SKB coalescing in TCP needs to have stricter checks, otherwise we'll
try to coalesce overlapping frags and crash. Fix from Eric Dumazet.
5) RCU routing table lookups can race with free_fib_info(), causing
crashes when we deref the device pointers in the route. Fix by
releasing the net device in the RCU callback. From Yanmin Zhang.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (293 commits)
tcp: take care of overlaps in tcp_try_coalesce()
ipv4: fix the rcu race between free_fib_info and ip_route_output_slow
mm: add a low limit to alloc_large_system_hash
ipx: restore token ring define to include/linux/ipx.h
if: restore token ring ARP type to header
xen: do not disable netfront in dom0
phy/micrel: Fix ID of KSZ9021
mISDN: Add X-Tensions USB ISDN TA XC-525
gianfar:don't add FCB length to hard_header_len
Bluetooth: Report proper error number in disconnection
Bluetooth: Create flags for bt_sk()
Bluetooth: report the right security level in getsockopt
Bluetooth: Lock the L2CAP channel when sending
Bluetooth: Restore locking semantics when looking up L2CAP channels
Bluetooth: Fix a redundant and problematic incoming MTU check
Bluetooth: Add support for Foxconn/Hon Hai AR5BBU22 0489:E03C
Bluetooth: Fix EIR data generation for mgmt_device_found
Bluetooth: Fix Inquiry with RSSI event mask
Bluetooth: improve readability of l2cap_seq_list code
Bluetooth: Fix skb length calculation
...
Sergio Correia reported following warning :
WARNING: at net/ipv4/tcp.c:1301 tcp_cleanup_rbuf+0x4f/0x110()
WARN(skb && !before(tp->copied_seq, TCP_SKB_CB(skb)->end_seq),
"cleanup rbuf bug: copied %X seq %X rcvnxt %X\n",
tp->copied_seq, TCP_SKB_CB(skb)->end_seq, tp->rcv_nxt);
It appears TCP coalescing, and more specifically commit b081f85c29
(net: implement tcp coalescing in tcp_queue_rcv()) should take care of
possible segment overlaps in receive queue. This was properly done in
the case of out_or_order_queue by the caller.
For example, segment at tail of queue have sequence 1000-2000, and we
add a segment with sequence 1500-2500.
This can happen in case of retransmits.
In this case, just don't do the coalescing.
Reported-by: Sergio Correia <lists@uece.net>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Tested-by: Sergio Correia <lists@uece.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
We hit a kernel OOPS.
<3>[23898.789643] BUG: sleeping function called from invalid context at
/data/buildbot/workdir/ics/hardware/intel/linux-2.6/arch/x86/mm/fault.c:1103
<3>[23898.862215] in_atomic(): 0, irqs_disabled(): 0, pid: 10526, name:
Thread-6683
<4>[23898.967805] HSU serial 0000:00:05.1: 0000:00:05.2:HSU serial prevented me
to suspend...
<4>[23899.258526] Pid: 10526, comm: Thread-6683 Tainted: G W
3.0.8-137685-ge7742f9 #1
<4>[23899.357404] HSU serial 0000:00:05.1: 0000:00:05.2:HSU serial prevented me
to suspend...
<4>[23899.904225] Call Trace:
<4>[23899.989209] [<c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.000416] [<c1238c2a>] __might_sleep+0x10a/0x110
<4>[23900.007357] [<c1228021>] do_page_fault+0xd1/0x3c0
<4>[23900.013764] [<c18e9ba9>] ? restore_all+0xf/0xf
<4>[23900.024024] [<c17c007b>] ? napi_complete+0x8b/0x690
<4>[23900.029297] [<c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.123739] [<c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.128955] [<c18ea0c3>] error_code+0x5f/0x64
<4>[23900.133466] [<c1227f50>] ? pgtable_bad+0x130/0x130
<4>[23900.138450] [<c17f6298>] ? __ip_route_output_key+0x698/0x7c0
<4>[23900.144312] [<c17f5f8d>] ? __ip_route_output_key+0x38d/0x7c0
<4>[23900.150730] [<c17f63df>] ip_route_output_flow+0x1f/0x60
<4>[23900.156261] [<c181de58>] ip4_datagram_connect+0x188/0x2b0
<4>[23900.161960] [<c18e981f>] ? _raw_spin_unlock_bh+0x1f/0x30
<4>[23900.167834] [<c18298d6>] inet_dgram_connect+0x36/0x80
<4>[23900.173224] [<c14f9e88>] ? _copy_from_user+0x48/0x140
<4>[23900.178817] [<c17ab9da>] sys_connect+0x9a/0xd0
<4>[23900.183538] [<c132e93c>] ? alloc_file+0xdc/0x240
<4>[23900.189111] [<c123925d>] ? sub_preempt_count+0x3d/0x50
Function free_fib_info resets nexthop_nh->nh_dev to NULL before releasing
fi. Other cpu might be accessing fi. Fixing it by delaying the releasing.
With the patch, we ran MTBF testing on Android mobile for 12 hours
and didn't trigger the issue.
Thank Eric for very detailed review/checking the issue.
Signed-off-by: Yanmin Zhang <yanmin_zhang@linux.intel.com>
Signed-off-by: Kun Jiang <kunx.jiang@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
UDP stack needs a minimum hash size value for proper operation and also
uses alloc_large_system_hash() for proper NUMA distribution of its hash
tables and automatic sizing depending on available system memory.
On some low memory situations, udp_table_init() must ignore the
alloc_large_system_hash() result and reallocs a bigger memory area.
As we cannot easily free old hash table, we leak it and kmemleak can
issue a warning.
This patch adds a low limit parameter to alloc_large_system_hash() to
solve this problem.
We then specify UDP_HTABLE_SIZE_MIN for UDP/UDPLite hash table
allocation.
Reported-by: Mark Asselstine <mark.asselstine@windriver.com>
Reported-by: Tim Bird <tim.bird@am.sony.com>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Pull user namespace enhancements from Eric Biederman:
"This is a course correction for the user namespace, so that we can
reach an inexpensive, maintainable, and reasonably complete
implementation.
Highlights:
- Config guards make it impossible to enable the user namespace and
code that has not been converted to be user namespace safe.
- Use of the new kuid_t type ensures the if you somehow get past the
config guards the kernel will encounter type errors if you enable
user namespaces and attempt to compile in code whose permission
checks have not been updated to be user namespace safe.
- All uids from child user namespaces are mapped into the initial
user namespace before they are processed. Removing the need to add
an additional check to see if the user namespace of the compared
uids remains the same.
- With the user namespaces compiled out the performance is as good or
better than it is today.
- For most operations absolutely nothing changes performance or
operationally with the user namespace enabled.
- The worst case performance I could come up with was timing 1
billion cache cold stat operations with the user namespace code
enabled. This went from 156s to 164s on my laptop (or 156ns to
164ns per stat operation).
- (uid_t)-1 and (gid_t)-1 are reserved as an internal error value.
Most uid/gid setting system calls treat these value specially
anyway so attempting to use -1 as a uid would likely cause
entertaining failures in userspace.
- If setuid is called with a uid that can not be mapped setuid fails.
I have looked at sendmail, login, ssh and every other program I
could think of that would call setuid and they all check for and
handle the case where setuid fails.
- If stat or a similar system call is called from a context in which
we can not map a uid we lie and return overflowuid. The LFS
experience suggests not lying and returning an error code might be
better, but the historical precedent with uids is different and I
can not think of anything that would break by lying about a uid we
can't map.
- Capabilities are localized to the current user namespace making it
safe to give the initial user in a user namespace all capabilities.
My git tree covers all of the modifications needed to convert the core
kernel and enough changes to make a system bootable to runlevel 1."
Fix up trivial conflicts due to nearby independent changes in fs/stat.c
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ebiederm/user-namespace: (46 commits)
userns: Silence silly gcc warning.
cred: use correct cred accessor with regards to rcu read lock
userns: Convert the move_pages, and migrate_pages permission checks to use uid_eq
userns: Convert cgroup permission checks to use uid_eq
userns: Convert tmpfs to use kuid and kgid where appropriate
userns: Convert sysfs to use kgid/kuid where appropriate
userns: Convert sysctl permission checks to use kuid and kgids.
userns: Convert proc to use kuid/kgid where appropriate
userns: Convert ext4 to user kuid/kgid where appropriate
userns: Convert ext3 to use kuid/kgid where appropriate
userns: Convert ext2 to use kuid/kgid where appropriate.
userns: Convert devpts to use kuid/kgid where appropriate
userns: Convert binary formats to use kuid/kgid where appropriate
userns: Add negative depends on entries to avoid building code that is userns unsafe
userns: signal remove unnecessary map_cred_ns
userns: Teach inode_capable to understand inodes whose uids map to other namespaces.
userns: Fail exec for suid and sgid binaries with ids outside our user namespace.
userns: Convert stat to return values mapped from kuids and kgids
userns: Convert user specfied uids and gids in chown into kuids and kgid
userns: Use uid_eq gid_eq helpers when comparing kuids and kgids in the vfs
...
Pull cgroup updates from Tejun Heo:
"cgroup file type addition / removal is updated so that file types are
added and removed instead of individual files so that dynamic file
type addition / removal can be implemented by cgroup and used by
controllers. blkio controller changes which will come through block
tree are dependent on this. Other changes include res_counter cleanup
and disallowing kthread / PF_THREAD_BOUND threads to be attached to
non-root cgroups.
There's a reported bug with the file type addition / removal handling
which can lead to oops on cgroup umount. The issue is being looked
into. It shouldn't cause problems for most setups and isn't a
security concern."
Fix up trivial conflict in Documentation/feature-removal-schedule.txt
* 'for-3.5' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup: (21 commits)
res_counter: Account max_usage when calling res_counter_charge_nofail()
res_counter: Merge res_counter_charge and res_counter_charge_nofail
cgroups: disallow attaching kthreadd or PF_THREAD_BOUND threads
cgroup: remove cgroup_subsys->populate()
cgroup: get rid of populate for memcg
cgroup: pass struct mem_cgroup instead of struct cgroup to socket memcg
cgroup: make css->refcnt clearing on cgroup removal optional
cgroup: use negative bias on css->refcnt to block css_tryget()
cgroup: implement cgroup_rm_cftypes()
cgroup: introduce struct cfent
cgroup: relocate __d_cgrp() and __d_cft()
cgroup: remove cgroup_add_file[s]()
cgroup: convert memcg controller to the new cftype interface
memcg: always create memsw files if CONFIG_CGROUP_MEM_RES_CTLR_SWAP
cgroup: convert all non-memcg controllers to the new cftype interface
cgroup: relocate cftype and cgroup_subsys definitions in controllers
cgroup: merge cft_release_agent cftype array into the base files array
cgroup: implement cgroup_add_cftypes() and friends
cgroup: build list of all cgroups under a given cgroupfs_root
cgroup: move cgroup_clear_directory() call out of cgroup_populate_dir()
...
Replace simple_strtoul with kstrtoul in three similar occurrences, all setup
handlers:
* route.c: set_rhash_entries
* tcp.c: set_thash_entries
* udp.c: set_uhash_entries
Also check if the conversion failed.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The __setup macro should follow the corresponding setup handler.
Signed-off-by: Eldad Zack <eldad@fogrefinery.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
ip_frag_reasm() can use skb_try_coalesce() to build optimized skb,
reducing memory used by them (truesize), and reducing number of cache
line misses and overhead for the consumer.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move tcp_try_coalesce() protocol independent part to
skb_try_coalesce().
skb_try_coalesce() can be used in IPv4 defrag and IPv6 reassembly,
to build optimized skbs (less sk_buff, and possibly less 'headers')
skb_try_coalesce() is zero copy, unless the copy can fit in destination
header (its a rare case)
kfree_skb_partial() is also moved to net/core/skbuff.c and exported,
because IPv6 will need it in patch (ipv6: use skb coalescing in
reassembly).
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- match() method returns a boolean
- return (A && B && C && D) -> return A && B && C && D
- fix indentation
Signed-off-by: Eric Dumazet <edumazet@google.com>
Since recent changes on TCP splicing (starting with commits 2f533844
"tcp: allow splice() to build full TSO packets" and 35f9c09f "tcp:
tcp_sendpages() should call tcp_push() once"), I started seeing
massive stalls when forwarding traffic between two sockets using
splice() when pipe buffers were larger than socket buffers.
Latest changes (net: netdev_alloc_skb() use build_skb()) made the
problem even more apparent.
The reason seems to be that if do_tcp_sendpages() fails on out of memory
condition without being able to send at least one byte, tcp_push() is not
called and the buffers cannot be flushed.
After applying the attached patch, I cannot reproduce the stalls at all
and the data rate it perfectly stable and steady under any condition
which previously caused the problem to be permanent.
The issue seems to have been there since before the kernel migrated to
git, which makes me think that the stalls I occasionally experienced
with tux during stress-tests years ago were probably related to the
same issue.
This issue was first encountered on 3.0.31 and 3.2.17, so please backport
to -stable.
Signed-off-by: Willy Tarreau <w@1wt.eu>
Acked-by: Eric Dumazet <edumazet@google.com>
Cc: <stable@vger.kernel.org>
bool conversions where possible.
__inline__ -> inline
space cleanups
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
bool/const conversions where possible
__inline__ -> inline
space cleanups
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the current debugging style and enable dynamic_debug.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We are going to delete the Token ring support. This removes any
special processing in the core networking for token ring, (aside
from net/tr.c itself), leaving the drivers and remaining tokenring
support present but inert.
The mass removal of the drivers and net/tr.c will be in a separate
commit, so that the history of these files that we still care
about won't have the giant deletion tied into their history.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Standardize the net core ratelimited logging functions.
Coalesce formats, align arguments.
Change a printk then vprintk sequence to use printf extension %pV.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
By making this a standalone config option (auto-selected as needed),
selecting CRYPTO from here rather than from XFRM (which is boolean)
allows the core crypto code to become a module again even when XFRM=y.
Signed-off-by: Jan Beulich <jbeulich@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As proposed by Eric, make the tcp_input.o thinner.
add/remove: 1/1 grow/shrink: 1/4 up/down: 868/-1329 (-461)
function old new delta
tcp_try_rmem_schedule - 864 +864
tcp_ack 4811 4815 +4
tcp_validate_incoming 817 815 -2
tcp_collapse 860 858 -2
tcp_send_rcvq 555 353 -202
tcp_data_queue 3435 3033 -402
tcp_prune_queue 721 - -721
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As noted by Eric, no checks are performed on the data size we're
putting in the read queue during repair. Thus, validate the given
data size with the common rmem management routine.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It actually works on the input queue and will use its read mem
routines, thus it's better to have in in the tcp_input.c file.
Signed-off-by: Pavel Emelyanov <xemul@parallels.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Due to RCU lookups and RCU based release, fib_info objects can
be found during lookup which have fi->fib_dead set.
We must ignore these entries, otherwise we risk dereferencing
the parts of the entry which are being torn down.
Reported-by: Yevgen Pronenko <yevgen.pronenko@sonymobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch removes ip_queue support which was marked as obsolete
years ago. The nfnetlink_queue modules provides more advanced
user-space packet queueing mechanism.
This patch also removes capability code included in SELinux that
refers to ip_queue. Otherwise, we break compilation.
Several warning has been sent regarding this to the mailing list
in the past month without anyone rising the hand to stop this
with some strong argument.
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
Conflicts:
drivers/net/ethernet/intel/e1000e/param.c
drivers/net/wireless/iwlwifi/iwl-agn-rx.c
drivers/net/wireless/iwlwifi/iwl-trans-pcie-rx.c
drivers/net/wireless/iwlwifi/iwl-trans.h
Resolved the iwlwifi conflict with mainline using 3-way diff posted
by John Linville and Stephen Rothwell. In 'net' we added a bug
fix to make iwlwifi report a more accurate skb->truesize but this
conflicted with RX path changes that happened meanwhile in net-next.
In e1000e a conflict arose in the validation code for settings of
adapter->itr. 'net-next' had more sophisticated logic so that
logic was used.
Signed-off-by: David S. Miller <davem@davemloft.net>
Until now, struct mreq has not been recognized and it was worked with
as with struct in_addr. That means imr_multiaddr was copied to
imr_address. So do recognize struct mreq here and copy that correctly.
Signed-off-by: Jiri Pirko <jpirko@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
It appears some networks play bad games with the two bits reserved for
ECN. This can trigger false congestion notifications and very slow
transferts.
Since RFC 3168 (6.1.1) forbids SYN packets to carry CT bits, we can
disable TCP ECN negociation if it happens we receive mangled CT bits in
the SYN packet.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Perry Lorier <perryl@google.com>
Cc: Matt Mathis <mattmathis@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Wilmer van der Gaast <wilmer@google.com>
Cc: Ankur Jain <jankur@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Dave Täht <dave.taht@bufferbloat.net>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support for a skb_head_is_locked helper function. It is
meant to be used any time we are considering transferring the head from
skb->head to a paged frag. If the head is locked it means we cannot remove
the head from the skb so it must be copied or we must take the skb as a
whole.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
As a first step to converting struct cred to be all kuid_t and kgid_t
values convert the group values stored in group_info to always be
kgid_t values. Unless user namespaces are used this change should
have no effect.
Acked-by: Serge Hallyn <serge.hallyn@canonical.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
This change cleans up the last bits of tcp_try_coalesce so that we only
need one goto which jumps to the end of the function. The idea is to make
the code more readable by putting things in a linear order so that we start
execution at the top of the function, and end it at the bottom.
I also made a slight tweak to the code for handling frags when we are a
clone. Instead of making it an if (clone) loop else nr_frags = 0 I changed
the logic so that if (!clone) we just set the number of frags to 0 which
disables the for loop anyway.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change reorders the code related to the use of an skb->head_frag so it
is placed before we check the rest of the frags. This allows the code to
read more linearly instead of like some sort of loop.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch addresses several issues in the way we were tracking the
truesize in tcp_try_coalesce.
First it was using ksize which prevents us from having a 0 sized head frag
and getting a usable result. To resolve that this patch uses the end
pointer which is set based off either ksize, or the frag_size supplied in
build_skb. This allows us to compute the original truesize of the entire
buffer and remove that value leaving us with just what was added as pages.
The second issue was the use of skb->len if there is a mergeable head frag.
We should only need to remove the size of an data aligned sk_buff from our
current skb->truesize to compute the delta for a buffer with a reused head.
By using skb->len the value of truesize was being artificially reduced
which means that head frags could use more memory than buffers using
standard allocations.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This change is meant ot prevent stealing the skb->head to use as a page in
the event that the skb->head was cloned. This allows the other clones to
track each other via shinfo->dataref.
Without this we break down to two methods for tracking the reference count,
one being dataref, the other being the page count. As a result it becomes
difficult to track how many references there are to skb->head.
Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Extend tcp coalescing implementing it from tcp_queue_rcv(), the main
receiver function when application is not blocked in recvmsg().
Function tcp_queue_rcv() is moved a bit to allow its call from
tcp_data_queue()
This gives good results especially if GRO could not kick, and if skb
head is a fragment.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Alexander Duyck <alexander.h.duyck@intel.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Before stealing fragments or skb head, we must make sure skbs are not
cloned.
Alexander was worried about destination skb being cloned : In bridge
setups, a driver could be fooled if skb->data_len would not match skb
nr_frags.
If source skb is cloned, we must take references on pages instead.
Bug happened using tcpdump (if not using mmap())
Introduce kfree_skb_partial() helper to cleanup code.
Reported-by: Alexander Duyck <alexander.h.duyck@intel.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
tcp_adv_win_scale default value is 2, meaning we expect a good citizen
skb to have skb->len / skb->truesize ratio of 75% (3/4)
In 2.6 kernels we (mis)accounted for typical MSS=1460 frame :
1536 + 64 + 256 = 1856 'estimated truesize', and 1856 * 3/4 = 1392.
So these skbs were considered as not bloated.
With recent truesize fixes, a typical MSS=1460 frame truesize is now the
more precise :
2048 + 256 = 2304. But 2304 * 3/4 = 1728.
So these skb are not good citizen anymore, because 1460 < 1728
(GRO can escape this problem because it build skbs with a too low
truesize.)
This also means tcp advertises a too optimistic window for a given
allocated rcvspace : When receiving frames, sk_rmem_alloc can hit
sk_rcvbuf limit and we call tcp_prune_queue()/tcp_collapse() too often,
especially when application is slow to drain its receive queue or in
case of losses (netperf is fast, scp is slow). This is a major latency
source.
We should adjust the len/truesize ratio to 50% instead of 75%
This patch :
1) changes tcp_adv_win_scale default to 1 instead of 2
2) increase tcp_rmem[2] limit from 4MB to 6MB to take into account
better truesize tracking and to allow autotuning tcp receive window to
reach same value than before. Note that same amount of kernel memory is
consumed compared to 2.6 kernels.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Implementing the advanced early retransmit (sysctl_tcp_early_retrans==2).
Delays the fast retransmit by an interval of RTT/4. We borrow the
RTO timer to implement the delay. If we receive another ACK or send
a new packet, the timer is cancelled and restored to original RTO
value offset by time elapsed. When the delayed-ER timer fires,
we enter fast recovery and perform fast retransmit.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch implements RFC 5827 early retransmit (ER) for TCP.
It reduces DUPACK threshold (dupthresh) if outstanding packets are
less than 4 to recover losses by fast recovery instead of timeout.
While the algorithm is simple, small but frequent network reordering
makes this feature dangerous: the connection repeatedly enter
false recovery and degrade performance. Therefore we implement
a mitigation suggested in the appendix of the RFC that delays
entering fast recovery by a small interval, i.e., RTT/4. Currently
ER is conservative and is disabled for the rest of the connection
after the first reordering event. A large scale web server
experiment on the performance impact of ER is summarized in
section 6 of the paper "Proportional Rate Reduction for TCP”,
IMC 2011. http://conferences.sigcomm.org/imc/2011/docs/p155.pdf
Note that Linux has a similar feature called THIN_DUPACK. The
differences are THIN_DUPACK do not mitigate reorderings and is only
used after slow start. Currently ER is disabled if THIN_DUPACK is
enabled. I would be happy to merge THIN_DUPACK feature with ER if
people think it's a good idea.
ER is enabled by sysctl_tcp_early_retrans:
0: Disables ER
1: Reduce dupthresh to packets_out - 1 when outstanding packets < 4.
2: (Default) reduce dupthresh like mode 1. In addition, delay
entering fast recovery by RTT/4.
Note: mode 2 is implemented in the third part of this patch series.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This a prepartion patch that refactors the code to enter recovery
into a new function tcp_enter_recovery(). It's needed to implement
the delayed fast retransmit in ER.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
TCP coalesce can check if skb to be merged has its skb->head mapped to a
page fragment, instead of a kmalloc() area.
We had to disable coalescing in this case, for performance reasons.
We 'upgrade' skb->head as a fragment in itself.
This reduces number of cache misses when user makes its copies, since a
less sk_buff are fetched.
This makes receive and ofo queues shorter and thus reduce cache line
misses in TCP stack.
This is a followup of patch "net: allow skb->head to be a page fragment"
Tested with tg3 nic, with GRO on or off. We can see "TCPRcvCoalesce"
counter being incremented.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi>
Cc: Herbert Xu <herbert@gondor.apana.org.au>
Cc: Maciej Żenczykowski <maze@google.com>
Cc: Neal Cardwell <ncardwell@google.com>
Cc: Tom Herbert <therbert@google.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: Matt Carlson <mcarlson@broadcom.com>
Cc: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When the cwnd reduction is done, ssthresh may be infinite
if TCP enters CWR via ECN or F-RTO. If cwnd is not undone, i.e.,
undo_marker is set, tcp_complete_cwr() falsely set cwnd to the
infinite ssthresh value. The correct operation is to keep cwnd
intact because it has been updated in ECN or F-RTO.
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Acked-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Clean up a reference to jiffies in tcp_rcv_rtt_measure() that should
instead reference tcp_time_stamp. Since the result of the subtraction
is passed into a function taking u32, this should not change any
behavior (and indeed the generated assembly does not change on
x86_64). However, it seems worth cleaning this up for consistency and
clarity (and perhaps to avoid bugs if this is copied and pasted
somewhere else).
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
David S. Miller