Result of skb_frag_dma_map() and dma_map_single() wasn't checked.
Added a check and proper handling in case of failure.
Moved the mapping to the beginning of mlx4_en_xmit(), before updating
the ring data structure to make error handling easier.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When hardware gets into error state, must notify user about it.
When QP in error state no traffic will be tx'ed from the attached
tx_ring.
Driver should know how to recover from this unexpected state. I will send later
on the recovery flow, but having the print shouldn't be delayed.
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Fix a bug when FC and PFC are enabled/disabled at the same time.
According to ConnectX-3 Programmer Manual these two features are mutial
exclusive. So make sure when enabling PFC to turn off global FC and
vise versa. Otherwise it hurts the performance.
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Amir Vadai <amirv@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Each function driver instance uses the MAC address of the
lowest function belonging to that physical port as a unique
port identifier. This port identifier is read and cached in
driver during probe and provided to user space through
ndo_get_phys_port_id()
Signed-off-by: Shahed Shaikh <shahed.shaikh@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Enable diagnostic test via ethtool and QConvergeConsole
application when Multiple Tx queues are enabled on 82xx
series adapters.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o using ethtool {set|get}_channel option, user can change number
of Tx queues for 82xx Series adapter.
o updated ethtool -S <ethX> option to display stats from each Tx queue.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 82xx firmware allows support for multiple Tx queues. This
patch will enable multi Tx queue support for 82xx series
adapter. Max number of Tx queues supported will be 8.
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some boards require custom PHY configuration, for example due to trace
length differences. Add the ability to configure these registers in
order to get the PHY to function on boards that need it.
Because PHYs are auto-detected based on MDIO device IDs, allow PHY
configuration to be specified in the parent Ethernet device node if no
PHY device node is present.
Signed-off-by: Sean Cross <xobs@kosagi.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Some phy's can be configured to enable wake on lan (e.g. at803x or marvell 88E1318S).
There is no way how to enable wol on CPSW with such connected phys. This patch
adds this support. It is provided by calling the phy's related code.
Tested on board with at8030x connected phy. Wol interrupt line is
connected to GPIO0 on am335x.
Signed-off-by: Matus Ujhelyi <ujhelyi.m@gmail.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
CPSW driver no longer supports platform register as all the SoCs which has CPSW
are supporting DT only booting, so moving cpsw.h header file from platform
include to drivers/net/ethernet/ti
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use devm_ioremap_resource instead of devm_request_and_ioremap.
This was done using the semantic patch
scripts/coccinelle/api/devm_ioremap_resource.cocci
The relevant call to platform_get_resource was manually moved down to the
call to devm_ioremap_resource.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Mugunthan V N <mugunthanvnm@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of_dev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Acked-by: Michal Simek <monstr@monstr.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &of->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &ofdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use the wrapper functions for getting and setting the driver data using
platform_device instead of using dev_{get,set}_drvdata() with &pdev->dev,
so we can directly pass a struct platform_device.
Signed-off-by: Libo Chen <libo.chen@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Now that the 'register_type' field of the 'sh_eth' driver's platform data is not
used by the driver anymore, it's time to remove it and its initializers from
the SH platform code. Also move *enum* declaring values for this field from
<linux/sh_eth.h> to the local driver's header file as they're only needed
by the driver itself now...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The register layout is a SoC characteristic, so it's wrong that it's stored
in the otherwise board specific platform data. Add 'register_type' field to
'struct sh_eth_cpu_data', initialize it properly for each SoC, and read it
from this structure instead of the platfrom data from now on...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the ndo_busy_poll handler. Use skb_mark_napi_id to mark receive
packets with the napi id. For each slice, use per-slice spinlock and
state variable to ensure that only one handler processes receive
pacekts.
Locking, statistics counters, and the ndo_busy_poll handler follow
those in the ixgbe driver. So, credit goes to that driver's authors.
Signed-off-by: Hyong-Youb Kim <hykim@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
When attempting to change e.g. the advertising mask when the link is down
ecmd->speed is -1 causing mii_ethtool_sset() to bail out.
This bug bit when connecting to a gigabit switch through a 4-pin (industrial)
cable, since link negotiation would not complete (both endpoints claimed to
be gigabit-capable, but this is not possible with only 4 pins).
Any attempt to fix this by setting autonegation to not offer 1000Mbps
failed as the setting would not be accepted while the link was still down...
Set ecmd->speed to SPEED_1000 to satisfy mii_ethtool_sset()
(the actual value of ecmd->speed doesn't matter as long as it is valid,
since a re-negotation is forced afterwards).
Signed-off-by: Anders Larsen <al@alarsen.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add the missing unlock before return from function moxart_mac_start_xmit()
in the error handling case.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
The callback function of call_rcu() just calls a kfree(), so we
can use kfree_rcu() instead of call_rcu() + callback function.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
The ethtool core will lower the requested length to the one returned by
get_regs_len, therefore no additional check is needed in the get_regs
function.
Reported-by: Ben Hutchings <bhutchings@solarflare.com>
Signed-off-by: Peter Wu <lekensteyn@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch generates a hardware crash notification (NETDEV_REBOOT)
during reset. After a hardware crash, ENIC resets all its resources
including queue pair filters programmed by USNIC. USNIC registers for
this notification, and on receiving it, reprograms the queue pair
filters.
Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds an interface for USNIC to proxy firmware commands
through ENIC.
Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch,
- Adds new firmware commands for the new Cisco Low Latency NIC
(aka. USNIC).
Signed-off-by: Neel Patel <neepatel@cisco.com>
Signed-off-by: Nishank Trivedi <nistrive@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Use appropriate firmware image file name based on device IDs.
Signed-off-by: Pratik Pujar <pratik.pujar@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o Loopback initiator function drivers should process loopback time extend AEN.
These AENs are triggered by the loopback time extend mailbox command
issued by the target function drivers.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
o 84xx adapters support VLAN stripping for PVID. Packets don't have
VLAN tag inserted in case of PVID. So packet should follow non vlan path.
o Use capability bit to set PVID mode.
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Manish Chopra <manish.chopra@qlogic.com>
Signed-off-by: Himanshu Madhani <himanshu.madhani@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch allows transmit side vlan offload for vxlan
devices.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Rather than having static headroom calculation, adjust headroom
according to target device.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch allows more code sharing between vxlan and ovs-vxlan.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Following patch adds data field to vxlan socket and export
vxlan handler api.
vh->data is required to store private data per vxlan handler.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Once we have ovs-vxlan functionality, one UDP port can be assigned
to kernel-vxlan or ovs-vxlan port. Therefore following patch adds
vxlan demux functionality, so that vxlan or ovs module can
register for particular port.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Use iptunnel_pull_header() for better code sharing.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Restructure vxlan-socket management APIs so that it can be
shared between vxlan and ovs modules.
This patch does not change any functionality.
Signed-off-by: Pravin B Shelar <pshelar@nicira.com>
v6-v7:
- get rid of zero refcnt vs from hashtable.
Signed-off-by: David S. Miller <davem@davemloft.net>
Split some parts of code into another function to simplify
tx_bottom(). Use while loop to replace the goto loop.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Move some declearation of variables in rx_bottom().
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Use r8152_get_tx_agg for getting tx agg list
- Replace submit rx with goto submit
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the type of contex of tx_agg and rx_agg from void * to
staruc r8152 *.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Amir Vadai