Commit Graph

1594 Commits

Author SHA1 Message Date
Michael Hennerich 2adcf194cb Blackfin: SIC: BF537: change default data/error relative priorities
Some peripherals might generate an error interrupt shortly after the
data interrupt due to the fact that the peripheral isn't serviced fast
enough.  In most cases this isn't a problem and is expected behavior.
This hasn't been a problem on most parts since you simply don't request
the error interrupt (or you leave it disabled while there is an expected
state) and do the peripheral status checking in the data interrupt.

The Blackfin SIC allows people to prioritize data and error interrupts,
and the Blackfin CEC allows interrupts of equal or higher priority to
nest.  The current default settings gives error interrupts a higher
priority than data interrupts.  So if an error occurs while processing
the data interrupt, it will be serviced immediately.

However, the error interrupt on the BF537 SIC cannot be enabled on a
per-peripheral basis.  Once the error interrupt is enabled for one
peripheral, it is automatically enabled for all peripherals.

Therefore lower the default multiplexed error interrupt priority so
most people need not worry themselves with this issue.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22 03:48:49 -04:00
Michael Hennerich 0891baef7d Blackfin: bf537-stamp: add example IIO resources
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22 03:48:49 -04:00
Barry Song 6fbfa0c418 Blackfin: bf537-stamp: use correct spi mode with ad2s90 parts
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22 03:48:48 -04:00
Cliff Cai 3cbcb1616c Blackfin: bf537-stamp: add example adau1373 i2c resources
Signed-off-by: Cliff Cai <cliff.cai@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22 03:48:48 -04:00
Yi Li a65912ca57 Blackfin: bf537-stamp: add example adav801/3 resources
Signed-off-by: Yi Li <yi.li@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22 03:48:47 -04:00
Barry Song 92b20f7fb2 Blackfin: bf537-stamp: add example ad1937 i2c resources
Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22 03:48:46 -04:00
Mike Frysinger 67d9963bd7 Blackfin: bf537-stamp: fix NAND resources
The NAND platform driver expects the registers to have a "mem"
resource type rather than "io".

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22 03:48:46 -04:00
Michael Hennerich 9e75894c50 Blackfin: boards: use proper irq flags with isp1362-hcd
With the recent kernel update the isp1362-hcd driver evaluates the
IORESOURCE_IRQ resource flags and requests the irq with the given
polarity/edge settings.  However the ISP1362 config requires low
level/edge interrupts.  Most of the Blackfin boards use some random
flag or no flag at all.  Make all boards use a know good flag
IORESOURCE_IRQ_LOWEDGE.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22 03:48:45 -04:00
Valentin Yakovenkov 657bb918d9 Blackfin: bf561-acvilon: fix NAND resources
The NAND platform driver expects the registers to have a "mem"
resource type rather than "io".

Signed-off-by: Valentin Yakovenkov <yakovenkov@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22 03:48:45 -04:00
Michael Hennerich bf80caf4f1 Blackfin: cm-bf548: add support for Socket CAN
Add platform resources for the on-chip CAN peripheral so we can use it.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22 03:48:44 -04:00
Barry Song 7ba80063e9 Blackfin: boards: update AD183x resources
Make sure we use the right Kconfig names and platform strings.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22 03:48:43 -04:00
Barry Song f9f0e3b1f7 Blackfin: bf537-stamp: update GPIO CS devices
Now that we've rewritten the GPIO CS handling in the Blackfin SPI
peripheral, we need to update the platform resources accordingly.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22 03:48:43 -04:00
Mike Frysinger 3d6437b35d Blackfin: punt short SPI MMR bit names
Now that the common header defines everything and the SPI drivers are
using it, we can drop these duplicated global namespace polluters.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-22 03:48:27 -04:00
Linus Torvalds e36f561a2c Merge git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-irqflags
* git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-2.6-irqflags:
  Fix IRQ flag handling naming
  MIPS: Add missing #inclusions of <linux/irq.h>
  smc91x: Add missing #inclusion of <linux/irq.h>
  Drop a couple of unnecessary asm/system.h inclusions
  SH: Add missing consts to sys_execve() declaration
  Blackfin: Rename IRQ flags handling functions
  Blackfin: Add missing dep to asm/irqflags.h
  Blackfin: Rename DES PC2() symbol to avoid collision
  Blackfin: Split the BF532 BFIN_*_FIO_FLAG() functions to their own header
  Blackfin: Split PLL code from mach-specific cdef headers
2010-10-21 14:37:27 -07:00
Mike Frysinger 5e8592dca3 spi/bfin_spi: combine duplicate SPI_CTL read/write logic
While combining things, also switch to the proper SPI bit define names.
This lets us punt the rarely used SPI defines.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:39 -04:00
Barry Song d3cc71f71a spi/bfin_spi: redo GPIO CS handling
The common SPI layers take care of detecting CS conflicts and preventing
two devices from claiming the same CS.  This causes problems for the GPIO
CS support we currently have as we are using CS0 to mean "GPIO CS".  But
if we have multiple devices using a GPIO CS, the common SPI layers see
multiple devices using the virtual "CS0" and reject any such attempts.

To make both work, we introduce an offset define.  This represents the
max number of hardware CS values that the SPI peripheral supports.  If
the CS is below this limit, we know we can use the hardware CS.  If it's
above, we treat it as a GPIO CS.  This keeps the CS unique as seen by
the common code and prevents conflicts.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:36 -04:00
Mike Frysinger 0d2c6de225 Blackfin: SPI: expand SPI bitmasks
Expand the BIT_CTL defines to use the naming convention of the hardware,
and expand the masks to cover all documented bits.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:35 -04:00
Mike Frysinger 201bbc6fd8 spi/bfin_spi: drop custom cs_change_per_word support
As David points out, the cs_change_per_word option isn't standard, nor is
anyone actually using it.  So punt all of the dead code considering it
makes up ~10% of the code size.

Reported-by: David Brownell <dbrownell@users.sourceforge.net>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-10-18 02:49:30 -04:00
Arnd Bergmann 6038f373a3 llseek: automatically add .llseek fop
All file_operations should get a .llseek operation so we can make
nonseekable_open the default for future file operations without a
.llseek pointer.

The three cases that we can automatically detect are no_llseek, seq_lseek
and default_llseek. For cases where we can we can automatically prove that
the file offset is always ignored, we use noop_llseek, which maintains
the current behavior of not returning an error from a seek.

New drivers should normally not use noop_llseek but instead use no_llseek
and call nonseekable_open at open time.  Existing drivers can be converted
to do the same when the maintainer knows for certain that no user code
relies on calling seek on the device file.

The generated code is often incorrectly indented and right now contains
comments that clarify for each added line why a specific variant was
chosen. In the version that gets submitted upstream, the comments will
be gone and I will manually fix the indentation, because there does not
seem to be a way to do that using coccinelle.

Some amount of new code is currently sitting in linux-next that should get
the same modifications, which I will do at the end of the merge window.

Many thanks to Julia Lawall for helping me learn to write a semantic
patch that does all this.

===== begin semantic patch =====
// This adds an llseek= method to all file operations,
// as a preparation for making no_llseek the default.
//
// The rules are
// - use no_llseek explicitly if we do nonseekable_open
// - use seq_lseek for sequential files
// - use default_llseek if we know we access f_pos
// - use noop_llseek if we know we don't access f_pos,
//   but we still want to allow users to call lseek
//
@ open1 exists @
identifier nested_open;
@@
nested_open(...)
{
<+...
nonseekable_open(...)
...+>
}

@ open exists@
identifier open_f;
identifier i, f;
identifier open1.nested_open;
@@
int open_f(struct inode *i, struct file *f)
{
<+...
(
nonseekable_open(...)
|
nested_open(...)
)
...+>
}

@ read disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
<+...
(
   *off = E
|
   *off += E
|
   func(..., off, ...)
|
   E = *off
)
...+>
}

@ read_no_fpos disable optional_qualifier exists @
identifier read_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t read_f(struct file *f, char *p, size_t s, loff_t *off)
{
... when != off
}

@ write @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
expression E;
identifier func;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
<+...
(
  *off = E
|
  *off += E
|
  func(..., off, ...)
|
  E = *off
)
...+>
}

@ write_no_fpos @
identifier write_f;
identifier f, p, s, off;
type ssize_t, size_t, loff_t;
@@
ssize_t write_f(struct file *f, const char *p, size_t s, loff_t *off)
{
... when != off
}

@ fops0 @
identifier fops;
@@
struct file_operations fops = {
 ...
};

@ has_llseek depends on fops0 @
identifier fops0.fops;
identifier llseek_f;
@@
struct file_operations fops = {
...
 .llseek = llseek_f,
...
};

@ has_read depends on fops0 @
identifier fops0.fops;
identifier read_f;
@@
struct file_operations fops = {
...
 .read = read_f,
...
};

@ has_write depends on fops0 @
identifier fops0.fops;
identifier write_f;
@@
struct file_operations fops = {
...
 .write = write_f,
...
};

@ has_open depends on fops0 @
identifier fops0.fops;
identifier open_f;
@@
struct file_operations fops = {
...
 .open = open_f,
...
};

// use no_llseek if we call nonseekable_open
////////////////////////////////////////////
@ nonseekable1 depends on !has_llseek && has_open @
identifier fops0.fops;
identifier nso ~= "nonseekable_open";
@@
struct file_operations fops = {
...  .open = nso, ...
+.llseek = no_llseek, /* nonseekable */
};

@ nonseekable2 depends on !has_llseek @
identifier fops0.fops;
identifier open.open_f;
@@
struct file_operations fops = {
...  .open = open_f, ...
+.llseek = no_llseek, /* open uses nonseekable */
};

// use seq_lseek for sequential files
/////////////////////////////////////
@ seq depends on !has_llseek @
identifier fops0.fops;
identifier sr ~= "seq_read";
@@
struct file_operations fops = {
...  .read = sr, ...
+.llseek = seq_lseek, /* we have seq_read */
};

// use default_llseek if there is a readdir
///////////////////////////////////////////
@ fops1 depends on !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier readdir_e;
@@
// any other fop is used that changes pos
struct file_operations fops = {
... .readdir = readdir_e, ...
+.llseek = default_llseek, /* readdir is present */
};

// use default_llseek if at least one of read/write touches f_pos
/////////////////////////////////////////////////////////////////
@ fops2 depends on !fops1 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read.read_f;
@@
// read fops use offset
struct file_operations fops = {
... .read = read_f, ...
+.llseek = default_llseek, /* read accesses f_pos */
};

@ fops3 depends on !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write.write_f;
@@
// write fops use offset
struct file_operations fops = {
... .write = write_f, ...
+	.llseek = default_llseek, /* write accesses f_pos */
};

// Use noop_llseek if neither read nor write accesses f_pos
///////////////////////////////////////////////////////////

@ fops4 depends on !fops1 && !fops2 && !fops3 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
identifier write_no_fpos.write_f;
@@
// write fops use offset
struct file_operations fops = {
...
 .write = write_f,
 .read = read_f,
...
+.llseek = noop_llseek, /* read and write both use no f_pos */
};

@ depends on has_write && !has_read && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier write_no_fpos.write_f;
@@
struct file_operations fops = {
... .write = write_f, ...
+.llseek = noop_llseek, /* write uses no f_pos */
};

@ depends on has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
identifier read_no_fpos.read_f;
@@
struct file_operations fops = {
... .read = read_f, ...
+.llseek = noop_llseek, /* read uses no f_pos */
};

@ depends on !has_read && !has_write && !fops1 && !fops2 && !has_llseek && !nonseekable1 && !nonseekable2 && !seq @
identifier fops0.fops;
@@
struct file_operations fops = {
...
+.llseek = noop_llseek, /* no read or write fn */
};
===== End semantic patch =====

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Cc: Julia Lawall <julia@diku.dk>
Cc: Christoph Hellwig <hch@infradead.org>
2010-10-15 15:53:27 +02:00
Michal Marek 239060b93b Merge branch 'kbuild/rc-fixes' into kbuild/kconfig
We need to revert the temporary hack in 71ebc01, hence the merge.
2010-10-12 15:09:06 +02:00
David Howells df9ee29270 Fix IRQ flag handling naming
Fix the IRQ flag handling naming.  In linux/irqflags.h under one configuration,
it maps:

	local_irq_enable() -> raw_local_irq_enable()
	local_irq_disable() -> raw_local_irq_disable()
	local_irq_save() -> raw_local_irq_save()
	...

and under the other configuration, it maps:

	raw_local_irq_enable() -> local_irq_enable()
	raw_local_irq_disable() -> local_irq_disable()
	raw_local_irq_save() -> local_irq_save()
	...

This is quite confusing.  There should be one set of names expected of the
arch, and this should be wrapped to give another set of names that are expected
by users of this facility.

Change this to have the arch provide:

	flags = arch_local_save_flags()
	flags = arch_local_irq_save()
	arch_local_irq_restore(flags)
	arch_local_irq_disable()
	arch_local_irq_enable()
	arch_irqs_disabled_flags(flags)
	arch_irqs_disabled()
	arch_safe_halt()

Then linux/irqflags.h wraps these to provide:

	raw_local_save_flags(flags)
	raw_local_irq_save(flags)
	raw_local_irq_restore(flags)
	raw_local_irq_disable()
	raw_local_irq_enable()
	raw_irqs_disabled_flags(flags)
	raw_irqs_disabled()
	raw_safe_halt()

with type checking on the flags 'arguments', and then wraps those to provide:

	local_save_flags(flags)
	local_irq_save(flags)
	local_irq_restore(flags)
	local_irq_disable()
	local_irq_enable()
	irqs_disabled_flags(flags)
	irqs_disabled()
	safe_halt()

with tracing included if enabled.

The arch functions can now all be inline functions rather than some of them
having to be macros.

Signed-off-by: David Howells <dhowells@redhat.com> [X86, FRV, MN10300]
Signed-off-by: Chris Metcalf <cmetcalf@tilera.com> [Tile]
Signed-off-by: Michal Simek <monstr@monstr.eu> [Microblaze]
Tested-by: Catalin Marinas <catalin.marinas@arm.com> [ARM]
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> [AVR]
Acked-by: Tony Luck <tony.luck@intel.com> [IA-64]
Acked-by: Hirokazu Takata <takata@linux-m32r.org> [M32R]
Acked-by: Greg Ungerer <gerg@uclinux.org> [M68K/M68KNOMMU]
Acked-by: Ralf Baechle <ralf@linux-mips.org> [MIPS]
Acked-by: Kyle McMartin <kyle@mcmartin.ca> [PA-RISC]
Acked-by: Paul Mackerras <paulus@samba.org> [PowerPC]
Acked-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [S390]
Acked-by: Chen Liqin <liqin.chen@sunplusct.com> [Score]
Acked-by: Matt Fleming <matt@console-pimps.org> [SH]
Acked-by: David S. Miller <davem@davemloft.net> [Sparc]
Acked-by: Chris Zankel <chris@zankel.net> [Xtensa]
Reviewed-by: Richard Henderson <rth@twiddle.net> [Alpha]
Reviewed-by: Yoshinori Sato <ysato@users.sourceforge.jp> [H8300]
Cc: starvik@axis.com [CRIS]
Cc: jesper.nilsson@axis.com [CRIS]
Cc: linux-cris-kernel@axis.com
2010-10-07 14:08:55 +01:00
David Howells 3b139cdb37 Blackfin: Rename IRQ flags handling functions
Rename h/w IRQ flags handling functions to be in line with what is expected for
the irq renaming patch.  This renames local_*_hw() to hard_local_*() using the
following perl command:

	perl -pi -e 's/local_irq_(restore|enable|disable)_hw/hard_local_irq_\1/ or s/local_irq_save_hw([_a-z]*)[(]flags[)]/flags = hard_local_irq_save\1()/' `find arch/blackfin/ -name "*.[ch]"`

and then fixing up asm/irqflags.h manually.

Additionally, arch/hard_local_save_flags() and arch/hard_local_irq_save() both
return the flags rather than passing it through the argument list.

Signed-off-by: David Howells <dhowells@redhat.com>
2010-10-07 14:08:52 +01:00
David Howells 5c74874bc9 Blackfin: Add missing dep to asm/irqflags.h
Add a missing dependency (mach/blackfin.h) to asm/irqflags.h so that
bfin_read_IMASK() can be used by inline functions.

Signed-off-by: David Howells <dhowells@redhat.com>
2010-10-07 14:08:51 +01:00
David Howells f3441945da Blackfin: Split the BF532 BFIN_*_FIO_FLAG() functions to their own header
Split the BF532 machine type BFIN_*_FIO_FLAG() functions to their own header
file to avoid circular #include problems as these functions require IRQ flag
handling, which requires asm/blackfin.h, which otherwise requires the header
file that defines these functions.

For good measure, also get rid of the inclusion of asm/blackfin.h from
mach/cdefBF532.h (which is circular) and defBF532.h (which is included by
asm/blackfin.h before including this header).

Signed-off-by: David Howells <dhowells@redhat.com>
2010-10-07 14:08:50 +01:00
David Howells 3dcc1e7f9f Blackfin: Split PLL code from mach-specific cdef headers
Split the PLL control code from the Blackfin machine-specific cdef headers so
that the irqflags functions can be renamed without incurring a header loop.

Signed-off-by: David Howells <dhowells@redhat.com>
2010-10-07 14:08:49 +01:00
Arnaud Lacombe 838a2e55e6 kbuild: migrate all arch to the kconfig mainmenu upgrade
Signed-off-by: Arnaud Lacombe <lacombar@gmail.com>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Reviewed-by: Michal Marek <mmarek@suse.cz>
2010-09-19 22:54:11 -04:00
Barry Song 9e5610a995 Blackfin: bf52x/bf54x boards: drop unused nand page size
Now that the driver for the Blackfin on-chip NFC no longer uses/respects
the page_size from the platform resources (figures out the needs on the
fly), drop it from the platform resources.  This fixes some build errors
since the defines no longer exists.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-27 16:08:43 -04:00
Mike Frysinger ac0a5042be Blackfin: punt duplicate SPORT MMR defines
The common bfin_sport.h header now has unified definitions of these, so
stop polluting the global namespace.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-27 15:58:27 -04:00
Mike Frysinger f3411b16c7 Blackfin: wire up new fanotify/prlimit64 syscalls
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-23 04:24:09 -04:00
Mike Frysinger 97e94c3a57 Blackfin: fix hweight breakage
The recent commit to add constant optimization to hweight implicitly broke
the Blackfin arch.  Seems we were missed when all the other arches were
fixed with renames.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-23 04:24:08 -04:00
David Howells d7627467b7 Make do_execve() take a const filename pointer
Make do_execve() take a const filename pointer so that kernel_execve() compiles
correctly on ARM:

arch/arm/kernel/sys_arm.c:88: warning: passing argument 1 of 'do_execve' discards qualifiers from pointer target type

This also requires the argv and envp arguments to be consted twice, once for
the pointer array and once for the strings the array points to.  This is
because do_execve() passes a pointer to the filename (now const) to
copy_strings_kernel().  A simpler alternative would be to cast the filename
pointer in do_execve() when it's passed to copy_strings_kernel().

do_execve() may not change any of the strings it is passed as part of the argv
or envp lists as they are some of them in .rodata, so marking these strings as
const should be fine.

Further kernel_execve() and sys_execve() need to be changed to match.

This has been test built on x86_64, frv, arm and mips.

Signed-off-by: David Howells <dhowells@redhat.com>
Tested-by: Ralf Baechle <ralf@linux-mips.org>
Acked-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-17 18:07:43 -07:00
Linus Torvalds 7355a5a654 Merge git://git.infradead.org/mtd-2.6
* git://git.infradead.org/mtd-2.6:
  mtd/nand_ids: Fix buswidth
  mtd/m25p80: fix test for end of loop
  mtd/m25p80: retlen is never NULL
  MIPS: Fix gen_nand probe structures contents
  gen_nand: Test if nr_chips field is valid
  BFIN: Fix gen_nand probe structures contents
  nand/denali: move all hardware initialization work to denali_hw_init
  nand/denali: Add a page check in denali_read_page & denali_read_page_raw
  nand/denali: use cpu_relax() while waiting for hardware interrupt
  nand/denali: change read_status function method
  nand/denali: Fixed check patch warnings
  ARM: Fix gen_nand probe structures contents
  mtd/nand_base: fix kernel-doc warnings & typos
  nand/denali: use dev_xx debug function to replace nand_dbg_print and some printk
  nand/denali: Fixed handle ECC error bugs
  nand/denali: use iowrite32() to replace denali_write32()
  nand/denali: Fixed probe function bugs
2010-08-15 17:32:47 -07:00
Sam Ravnborg 8b1bb90701 defconfig reduction
Use the defconfig files generated by "make savedefconfig" for
remaining defconfig files.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
2010-08-14 22:26:53 +02:00
Sam Ravnborg bf56fba670 archs: replace unifdef-y with header-y
unifdef-y and header-y have same semantic, so drop unifdef-y

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
2010-08-14 22:26:51 +02:00
David Howells c788732523 Mark arguments to certain syscalls as being const
Mark arguments to certain system calls as being const where they should be but
aren't.  The list includes:

 (*) The filename arguments of various stat syscalls, execve(), various utimes
     syscalls and some mount syscalls.

 (*) The filename arguments of some syscall helpers relating to the above.

 (*) The buffer argument of various write syscalls.

Signed-off-by: David Howells <dhowells@redhat.com>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-13 16:53:13 -07:00
Marek Vasut ef56609f9c BFIN: Fix gen_nand probe structures contents
These two platforms didn't properly fill nr_chips in gen_nand 
registration and therefore depended on gen_nand bug fixed by by commit
81cbb0b177 ("mtd: gen_nand: fix support for
multiple chips")

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-08-12 12:17:32 +01:00
FUJITA Tomonori 3b9c6c11f5 dma-mapping: remove dma_is_consistent API
Architectures implement dma_is_consistent() in different ways (some
misinterpret the definition of API in DMA-API.txt).  So it hasn't been so
useful for drivers.  We have only one user of the API in tree.  Unlikely
out-of-tree drivers use the API.

Even if we fix dma_is_consistent() in some architectures, it doesn't look
useful at all.  It was invented long ago for some old systems that can't
allocate coherent memory at all.  It's better to export only APIs that are
definitely necessary for drivers.

Let's remove this API.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: James Bottomley <James.Bottomley@HansenPartnership.com>
Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 08:59:21 -07:00
FUJITA Tomonori 4565f0170d dma-mapping: unify dma_get_cache_alignment implementations
dma_get_cache_alignment returns the minimum DMA alignment.  Architectures
defines it as ARCH_DMA_MINALIGN (formally ARCH_KMALLOC_MINALIGN).  So we
can unify dma_get_cache_alignment implementations.

Note that some architectures implement dma_get_cache_alignment wrongly.
dma_get_cache_alignment() should return the minimum DMA alignment.  So
fully-coherent architectures should return 1.  This patch also fixes this
issue.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 08:59:21 -07:00
FUJITA Tomonori a6eb9fe105 dma-mapping: rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN
Now each architecture has the own dma_get_cache_alignment implementation.

dma_get_cache_alignment returns the minimum DMA alignment.  Architectures
define it as ARCH_KMALLOC_MINALIGN (it's used to make sure that malloc'ed
buffer is DMA-safe; the buffer doesn't share a cache with the others).  So
we can unify dma_get_cache_alignment implementations.

This patch:

dma_get_cache_alignment() needs to know if an architecture defines
ARCH_KMALLOC_MINALIGN or not (needs to know if architecture has DMA
alignment restriction).  However, slab.h define ARCH_KMALLOC_MINALIGN if
architectures doesn't define it.

Let's rename ARCH_KMALLOC_MINALIGN to ARCH_DMA_MINALIGN.
ARCH_KMALLOC_MINALIGN is used only in the internals of slab/slob/slub
(except for crypto).

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: <linux-arch@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-11 08:59:21 -07:00
Jiri Kosina 6396fc3b3f Merge branch 'master' into for-next
Conflicts:
	fs/exofs/inode.c
2010-08-11 09:36:51 +02:00
Linus Torvalds 2f9e825d3e Merge branch 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block
* 'for-2.6.36' of git://git.kernel.dk/linux-2.6-block: (149 commits)
  block: make sure that REQ_* types are seen even with CONFIG_BLOCK=n
  xen-blkfront: fix missing out label
  blkdev: fix blkdev_issue_zeroout return value
  block: update request stacking methods to support discards
  block: fix missing export of blk_types.h
  writeback: fix bad _bh spinlock nesting
  drbd: revert "delay probes", feature is being re-implemented differently
  drbd: Initialize all members of sync_conf to their defaults [Bugz 315]
  drbd: Disable delay probes for the upcomming release
  writeback: cleanup bdi_register
  writeback: add new tracepoints
  writeback: remove unnecessary init_timer call
  writeback: optimize periodic bdi thread wakeups
  writeback: prevent unnecessary bdi threads wakeups
  writeback: move bdi threads exiting logic to the forker thread
  writeback: restructure bdi forker loop a little
  writeback: move last_active to bdi
  writeback: do not remove bdi from bdi_list
  writeback: simplify bdi code a little
  writeback: do not lose wake-ups in bdi threads
  ...

Fixed up pretty trivial conflicts in drivers/block/virtio_blk.c and
drivers/scsi/scsi_error.c as per Jens.
2010-08-10 15:22:42 -07:00
Linus Torvalds e8a89cebdb Merge git://git.infradead.org/mtd-2.6
* git://git.infradead.org/mtd-2.6: (79 commits)
  mtd: Remove obsolete <mtd/compatmac.h> include
  mtd: Update copyright notices
  jffs2: Update copyright notices
  mtd-physmap: add support users can assign the probe type in board files
  mtd: remove redwood map driver
  mxc_nand: Add v3 (i.MX51) Support
  mxc_nand: support 8bit ecc
  mxc_nand: fix correct_data function
  mxc_nand: add V1_V2 namespace to registers
  mxc_nand: factor out a check_int function
  mxc_nand: make some internally used functions overwriteable
  mxc_nand: rework get_dev_status
  mxc_nand: remove 0xe00 offset from registers
  mtd: denali: Add multi connected NAND support
  mtd: denali: Remove set_ecc_config function
  mtd: denali: Remove unuseful code in get_xx_nand_para functions
  mtd: denali: Remove device_info_tag structure
  mtd: m25p80: add support for the Winbond W25Q32 SPI flash chip
  mtd: m25p80: add support for the Intel/Numonyx {16,32,64}0S33B SPI flash chips
  mtd: m25p80: add support for the EON EN25P{32, 64} SPI flash chips
  ...

Fix up trivial conflicts in drivers/mtd/maps/{Kconfig,redwood.c} due to
redwood driver removal.
2010-08-10 11:49:21 -07:00
Jiri Kosina fb8231a8b1 Merge branch 'master' into for-next
Conflicts:
	arch/arm/mach-omap1/board-nokia770.c
2010-08-10 13:22:08 +02:00
Linus Torvalds 0fc2f13722 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (32 commits)
  Blackfin: gpio: add a debounce stub
  Blackfin: update defconfigs
  Blackfin: remove CONFIG_MEM_GENERIC_BOARD
  Blackfin: dpmc: punt unnecessary RTC_ISTAT clearing
  Blackfin: unify rotary encoder bitmasks
  Blackfin: unify SDH/RSI bitmasks
  Blackfin: BF54x: tweak DMAC MMR naming to match other ports
  Blackfin: TWI: clean up the MMR names
  Blackfin: add EVT_OVERRIDE/IPRIO core MMR helpers
  Blackfin: add support for dynamic ftrace
  Blackfin: add support for LZO compressed kernels
  Blackfin: portmux: fix peripheral map overflow when requesting pins
  Blackfin: document SPI CS limitations with CPHA=0
  Blackfin: remove useless and outdated documentation
  Blackfin: BF51x/BF52x: support GPIO Hysteresis/Schmitt Trigger options
  Blackfin: gpio/portmux: clean up whitespace corruption
  Blackfin: make sure mmiowb inserts a write barrier with SSYNC
  Blackfin: fix DMA/cache bug when resuming from suspend to RAM
  Blackfin: BF51x: fix handling of PH8 (the "internal" SPI0SEL4 pin)
  Blackfin: add a GPIO_DEFAULT_BOOT_SPI_CS
  ...
2010-08-09 21:01:11 -07:00
Stefan Weil eef35c2d41 Fix spelling fuction -> function in comments
To avoid more patches, I also fixed other spelling
and grammar bugs when they were in the same or
following line:

successfull -> successful
parse -> parses
controler -> controller
controlers -> controllers

Cc: Jiri Kosina <trivial@kernel.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Stefan Weil <weil@mail.berlios.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2010-08-09 11:22:49 +02:00
FUJITA Tomonori 7e005f7979 remove needless ISA_DMA_THRESHOLD
Architectures don't need to define ISA_DMA_THRESHOLD anymore.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: James Bottomley <James.Bottomley@suse.de>
Acked-by: David Howells <dhowells@redhat.com>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
2010-08-07 18:15:50 +02:00
Linus Torvalds b62ad9ab18 Merge branch 'timers-timekeeping-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'timers-timekeeping-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  um: Fix read_persistent_clock fallout
  kgdb: Do not access xtime directly
  powerpc: Clean up obsolete code relating to decrementer and timebase
  powerpc: Rework VDSO gettimeofday to prevent time going backwards
  clocksource: Add __clocksource_updatefreq_hz/khz methods
  x86: Convert common clocksources to use clocksource_register_hz/khz
  timekeeping: Make xtime and wall_to_monotonic static
  hrtimer: Cleanup direct access to wall_to_monotonic
  um: Convert to use read_persistent_clock
  timkeeping: Fix update_vsyscall to provide wall_to_monotonic offset
  powerpc: Cleanup xtime usage
  powerpc: Simplify update_vsyscall
  time: Kill off CONFIG_GENERIC_TIME
  time: Implement timespec_add
  x86: Fix vtime/file timestamp inconsistencies

Trivial conflicts in Documentation/feature-removal-schedule.txt

Much less trivial conflicts in arch/powerpc/kernel/time.c resolved as
per Thomas' earlier merge commit 47916be4e2 ("Merge branch
'powerpc.cherry-picks' into timers/clocksource")
2010-08-06 13:18:29 -07:00
Mike Frysinger aab2393e2e Blackfin: gpio: add a debounce stub
The GPIO API was extended recently to include debounce functions, but
since the on-chip Blackfin GPIO modules don't support this stuff, make
a stub in the non-GPIOLIB case so drivers build properly.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:58 -04:00
Mike Frysinger bad6b094ad Blackfin: update defconfigs
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:58 -04:00
Christian Dietrich efbd24b5b0 Blackfin: remove CONFIG_MEM_GENERIC_BOARD
MEM_GENERIC_BOARD depends on GENERIC_BOARD, but this flag was removed
in 4f25eb85d6, therefore all references
to it from the source can be removed.

Signed-off-by: Christian Dietrich <qy03fugy@stud.informatik.uni-erlangen.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:57 -04:00
Michael Hennerich f619ddd4fe Blackfin: dpmc: punt unnecessary RTC_ISTAT clearing
The RTC ISTAT bits do not affect wakeups, and the RTC driver already
takes care of clearing this MMR when necessary.  So drop the useless
clearing in the core Blackfin power code.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:57 -04:00
Mike Frysinger 3975032405 Blackfin: unify rotary encoder bitmasks
Avoid duplication and ugly global namespace pollution.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:56 -04:00
Mike Frysinger c385acceb4 Blackfin: unify SDH/RSI bitmasks
Avoid duplication and ugly global namespace pollution.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:56 -04:00
Mike Frysinger 2b73a19f2d Blackfin: BF54x: tweak DMAC MMR naming to match other ports
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:55 -04:00
Mike Frysinger ba3f5973ce Blackfin: TWI: clean up the MMR names
The standard short name for control is CTL and not CTRL.  Use TWI0_xxx
even on parts that only have one TWI bus to keep things simple.  Drop
all the cdef helpers since the bus driver takes care of everything.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:55 -04:00
Mike Frysinger ada091729e Blackfin: add EVT_OVERRIDE/IPRIO core MMR helpers
These were partially defined, so fill out the def/cdef pieces properly.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:54 -04:00
Mike Frysinger f507442962 Blackfin: add support for dynamic ftrace
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:54 -04:00
Mike Frysinger 67df6cc665 Blackfin: add support for LZO compressed kernels
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:53 -04:00
Michael Hennerich 382dbe5b39 Blackfin: portmux: fix peripheral map overflow when requesting pins
Some processors have groups of pins that aren't an even number of 16.
This causes the array size calculation to under count the number of
needed entries due to integer truncation.  So on the BF51x, while we
should have 3 bitmaps (41 / 16), we end up with 2 and pin requests for
the 3rd bank end up scribbling over the top of the GPIO IRQ array.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:53 -04:00
Michael Hennerich 7a4a207e74 Blackfin: BF51x/BF52x: support GPIO Hysteresis/Schmitt Trigger options
Newer parts have optional Hysteresis/Schmitt Trigger options to help with
dirty signals.  So add some kconfig options for tuning this and enable it
by default for people.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:52 -04:00
Mike Frysinger 812ae98f08 Blackfin: gpio/portmux: clean up whitespace corruption
Random tabs instead of spaces, mixes of the two, and unicode spaces
instead of ascii spaces.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:51 -04:00
Michael Hennerich eb9649095f Blackfin: make sure mmiowb inserts a write barrier with SSYNC
Add SSYNC to our implementation of I/O write barrier to ensure ordering
of I/O space writes.  This will make sure that writes following the
barrier will arrive after all previous writes.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:51 -04:00
Michael Hennerich d1401e1dc2 Blackfin: fix DMA/cache bug when resuming from suspend to RAM
The dma_memcpy() function takes care of flushing different caches for us.
Normally this is what we want, but when resuming from mem, we don't yet
have caches enabled.  If these functions happen to be placed into L1 mem
(which is what we're trying to relocate), then things aren't going to
work.  So define a non-cache dma_memcpy() variant to utilize in situations
like this.

Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:50 -04:00
Mike Frysinger 502c8a0e07 Blackfin: BF51x: fix handling of PH8 (the "internal" SPI0SEL4 pin)
Even though the PH8 pin is only internal to the processor packaging, it
can be controlled like any other GPIO pin.  Now that we have a proper GPIO
define, we can fix the SPI0 CS4 define for the internal SPI flash.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:49 -04:00
Mike Frysinger 306208f40c Blackfin: add a GPIO_DEFAULT_BOOT_SPI_CS
This is parallel to the existing P_DEFAULT_BOOT_SPI_CS, but in terms of
the GPIO value so it can be used with the normal gpio API.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:49 -04:00
Mike Frysinger a13265af99 Blackfin: fix typo in hweight asm
Run ONES on the incoming value rather than random garbage.  This fixes
random crashes with some networking code.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:49 -04:00
Mike Frysinger 1ae9ab17e7 Blackfin: BF51x: fix typo in HWAIT pin define
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:48 -04:00
Mike Frysinger 399408276d Blackfin: BF54x: add ifdef protection to gpio header
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:48 -04:00
Mike Frysinger 332824b835 Blackfin: gpio: unify & clean up reserved map handling
The duplicated bit banging logic is getting out of hand, so unify the
local API to make management a lot easier.  This also makes the code
a lot easier to follow.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:47 -04:00
Mike Frysinger 74181295fb Blackfin: allow cache funcs to be in L1 for IFLUSH Anomaly 05000491
Anomaly 05000491 says that IFLUSH cannot have certain types of memory
stalls triggered before it has completed in order to function correctly.
One such condition is that it be in L1 instruction.  So add a config
option to move it there, default it to on, and throw up a warning when
it is turned off and this anomaly exists.

Since the anomaly should be worked around, we can drop the older method
of calling IFLUSH multiple times.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
2010-08-06 12:55:47 -04:00
Mike Frysinger dc7101bbae Blackfin: update anomaly lists to latest public info
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:46 -04:00
Mike Frysinger 5369fba136 Blackfin: merge anomalies 475 and 220 to follow official lists
Design found that these anomalies had the same root issue, so they've
merged 475 into 220.  We need to do the same to update to the latest
anomaly sheets.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:46 -04:00
Mike Frysinger 1ed181f248 Blackfin: move MPU anomaly check to common location
Keep all anomaly/arch checks in one place to keep logic simple.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:45 -04:00
Mike Frysinger d49e8e7e5a Blackfin: use common EXCEPTION_TABLE() in vmlinux.lds
Rather than do our own thing, use what common code provides.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:45 -04:00
Mike Frysinger 88a0ade952 Blackfin: stub fpregs dumping
The Blackfin processor has no FPU, so there are no FPU regs to dump.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:44 -04:00
Mike Frysinger f2521ce9ce Blackfin: new dynamic bfin read/write mmr helpers
These are useful when working with C structs of MMRs as the appropriate
size is selected based on the given argument.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:44 -04:00
Mike Frysinger 222f6eb66e Blackfin: punt NFC MMR bits
Now that the NFC driver has its own defines, scrub the ones from the
global namespace to avoid ugly collisions with common code.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-08-06 12:55:43 -04:00
Linus Torvalds 4aed2fd8e3 Merge branch 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip
* 'perf-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (162 commits)
  tracing/kprobes: unregister_trace_probe needs to be called under mutex
  perf: expose event__process function
  perf events: Fix mmap offset determination
  perf, powerpc: fsl_emb: Restore setting perf_sample_data.period
  perf, powerpc: Convert the FSL driver to use local64_t
  perf tools: Don't keep unreferenced maps when unmaps are detected
  perf session: Invalidate last_match when removing threads from rb_tree
  perf session: Free the ref_reloc_sym memory at the right place
  x86,mmiotrace: Add support for tracing STOS instruction
  perf, sched migration: Librarize task states and event headers helpers
  perf, sched migration: Librarize the GUI class
  perf, sched migration: Make the GUI class client agnostic
  perf, sched migration: Make it vertically scrollable
  perf, sched migration: Parameterize cpu height and spacing
  perf, sched migration: Fix key bindings
  perf, sched migration: Ignore unhandled task states
  perf, sched migration: Handle ignored migrate out events
  perf: New migration tool overview
  tracing: Drop cpparg() macro
  perf: Use tracepoint_synchronize_unregister() to flush any pending tracepoint call
  ...

Fix up trivial conflicts in Makefile and drivers/cpufreq/cpufreq.c
2010-08-06 09:30:52 -07:00
Barry Song 44299179c0 mtd: Blackfin NFC: fix handling of page sizes
Rather than forcing the platform resources to declare the desired page
size, simply use the existing information passed down to us by the higher
layers.  This way we work out of the box with all flash chips that the
kernel knows about.

Signed-off-by: Barry Song <barry.song@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-08-05 16:14:38 +01:00
Michal Marek 772320e845 Merge commit 'v2.6.35' into kbuild/kbuild
Conflicts:
	arch/powerpc/Makefile
2010-08-04 13:59:13 +02:00
Sam Ravnborg 6588169d51 kbuild: allow assignment to {A,C,LD}FLAGS_MODULE on the command line
It is now possible to assign options to AS, CC and LD
on the command line - which is only used when building modules.

{A,C,LD}FLAGS_MODULE was all used both in the top-level Makefile
in the arch makefiles, thus users had no way to specify
additional options to AS, CC, LD when building modules
without overriding the original value.

Introduce a new set of variables KBUILD_{A,C,LD}FLAGS_MODULE
that is used by arch specific files and free up
{A,C,LD}FLAGS_MODULE so they can be assigned on
the command line.

All arch Makefiles that used the old variables has been updated.

Note: Previously we had a MODFLAGS variable for both
AS and CC. But in favour of consistency this was dropped.
So in some cases arch Makefile has one assignmnet replaced by
two assignmnets.

Note2: MODFLAGS was not documented and is dropped
without any notice. I do not expect much/any breakage
from this.

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Cc: Denys Vlasenko <vda.linux@googlemail.com>
Cc: Haavard Skinnemoen <hskinnemoen@atmel.com>
Cc: Mike Frysinger <vapier@gentoo.org>
Cc: Tony Luck <tony.luck@intel.com>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Ralf Baechle <ralf@linux-mips.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Chen Liqin <liqin.chen@sunplusct.com>
Acked-by: Mike Frysinger <vapier@gentoo.org> [blackfin]
Acked-by: Haavard Skinnemoen <haavard.skinnemoen@atmel.com> [avr32]
Signed-off-by: Michal Marek <mmarek@suse.cz>
2010-08-03 14:09:45 +02:00
John Stultz 592913ecb8 time: Kill off CONFIG_GENERIC_TIME
Now that all arches have been converted over to use generic time via
clocksources or arch_gettimeoffset(), we can remove the GENERIC_TIME
config option and simplify the generic code.

Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-4-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2010-07-27 12:40:54 +02:00
Peter Zijlstra 1996bda2a4 arch: Implement local64_t
On 64bit, local_t is of size long, and thus we make local64_t an alias.
On 32bit, we fall back to atomic64_t. (architecture can provide optimized
32-bit version)

(This new facility is to be used by perf events optimizations.)

Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: linux-arch@vger.kernel.org
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
2010-06-09 11:12:36 +02:00
FUJITA Tomonori 459d42b72c blackfin: use use asm-generic/scatterlist.h
Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Cc: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-05-27 09:12:55 -07:00
Mike Frysinger 9c1a125921 ptrace: unify FDPIC implementations
The Blackfin/FRV/SuperH guys all have the same exact FDPIC ptrace code in
their arch handlers (since they were probably copied & pasted).  Since
these ptrace interfaces are an arch independent aspect of the FDPIC code,
unify them in the common ptrace code so new FDPIC ports don't need to copy
and paste this fundamental stuff yet again.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Acked-by: Roland McGrath <roland@redhat.com>
Acked-by: David Howells <dhowells@redhat.com>
Acked-by: Paul Mundt <lethal@linux-sh.org>
Cc: Oleg Nesterov <oleg@redhat.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-05-27 09:12:44 -07:00
Linus Torvalds 064e297c32 Merge branch 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/vapier/blackfin: (30 commits)
  Blackfin: SMP: fix continuation lines
  Blackfin: acvilon: fix timeout usage for I2C
  Blackfin: fix typo in BF537 IRQ comment
  Blackfin: unify duplicate MEM_MT48LC32M8A2_75 kconfig options
  Blackfin: set ARCH_KMALLOC_MINALIGN
  Blackfin: use atomic kmalloc in L1 alloc so it too can be atomic
  Blackfin: another year of changes (update copyright in boot log)
  Blackfin: optimize strncpy a bit
  Blackfin: isram: clean up ITEST_COMMAND macro and improve the selftests
  Blackfin: move string functions to normal lib/ assembly
  Blackfin: SIC: cut down on IAR MMR reads a bit
  Blackfin: bf537-minotaur: fix build errors due to header changes
  Blackfin: kgdb: pass up the CC register instead of a 0 stub
  Blackfin: handle HW errors in the new "FAULT" printing code
  Blackfin: show the whole accumulator in the pseudo DBG insn
  Blackfin: support all possible registers in the pseudo instructions
  Blackfin: add support for the DBG (debug output) pseudo insn
  Blackfin: change the BUG opcode to an unused 16-bit opcode
  Blackfin: allow NMI watchdog to be used w/RETN as a scratch reg
  Blackfin: add support for the DBGA (debug assert) pseudo insn
  ...
2010-05-24 08:02:58 -07:00
Joe Perches db52ecc295 Blackfin: SMP: fix continuation lines
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-22 14:19:15 -04:00
Wolfram Sang efc5863eb5 Blackfin: acvilon: fix timeout usage for I2C
The timeout value is in jiffies, so it should be using HZ, not a plain
number. As '10000' is ambiguous, 1HZ is used as conservative default.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Cc: Valentin Yakovenkov <yakovenkov@gmail.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-22 14:19:15 -04:00
Michael Hennerich d016a21362 Blackfin: fix typo in BF537 IRQ comment
Signed-off-by: Michael Hennerich <michael.hennerich@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-22 14:19:14 -04:00
Mike Frysinger 084f9ebfd0 Blackfin: unify duplicate MEM_MT48LC32M8A2_75 kconfig options
Reported-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-22 14:19:13 -04:00
FUJITA Tomonori 76b99699a2 Blackfin: set ARCH_KMALLOC_MINALIGN
Architectures that handle DMA-non-coherent memory need to set
ARCH_KMALLOC_MINALIGN to make sure that kmalloc'ed buffer is DMA-safe:
the buffer doesn't share a cache with the others.

Signed-off-by: FUJITA Tomonori <fujita.tomonori@lab.ntt.co.jp>
Acked-by: Pekka Enberg <penberg@cs.helsinki.fi>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-22 14:19:13 -04:00
Mike Frysinger eb5400b613 Blackfin: use atomic kmalloc in L1 alloc so it too can be atomic
Some drivers allocate L1 SRAM in atomic contexts, so make sure these
functions also use GFP_ATOMIC to avoid BUG()'s.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-22 14:19:12 -04:00
Mike Frysinger be1577e378 Blackfin: another year of changes (update copyright in boot log)
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-22 14:19:11 -04:00
Robin Getz 648eee52cc Blackfin: optimize strncpy a bit
Add a little strncpy optimization which can easily cut boot time by 20%.

When the kernel is booting with initramfs, it builds up the filesystem
from a cpio archive by calling strncpy_from_user() via fs/namei.c's
do_getname() on every file in the archive (which can be lots) with a
length of PATH_MAX (1024).  This causes the dest of the strncpy to be
padded with many NUL bytes.

This optimization mostly causes these NUL bytes to be padded with a call
to memset() which is already optimized for filling memory quickly, but
the hardware loop helps a little bit as well.

Boot time measured with 'loglevel=0' so UART speed doesn't get in the way.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-22 14:19:11 -04:00
Mike Frysinger c70dcabc8e Blackfin: isram: clean up ITEST_COMMAND macro and improve the selftests
The IADDR2DTEST() macro had some duplicated logic with bit 11 and some
incorrect comments, so scrub all of that.

In order to verify these aren't a problem (and won't be in the future),
extend the self tests to operate on as much L1 SRAM as possible.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-22 14:19:10 -04:00
Robin Getz 479ba60358 Blackfin: move string functions to normal lib/ assembly
Since 'extern inline' doesn't work correctly in the context of the Linux
kernel (too many overriding defines), move the string functions to normal
lib/ assembly files (like the existing mem funcs).  This avoids the forced
inline all over the kernel and allows us to place them constantly in L1.

This also avoids some module failures when gcc inserts calls to string
functions but the kernel build system doesn't fully consult the library
archives.

Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-22 14:19:09 -04:00
Mike Frysinger 80fcdb9593 Blackfin: SIC: cut down on IAR MMR reads a bit
Tweak the for loops that operate on the SIC IAR system MMRs to avoid
re-reading them multiple times in a row.  System MMRs are a little
slower to access, so avoid the penalty when possible.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-22 14:19:09 -04:00
Mike Frysinger 11cabcb95e Blackfin: bf537-minotaur: fix build errors due to header changes
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-22 14:19:08 -04:00
Mike Frysinger d2db97bf6b Blackfin: kgdb: pass up the CC register instead of a 0 stub
While the CC pseudo register can be deduced from the ASTAT register, make
sure we set its value correctly instead of always stubbing it out as 0.
GDB itself looks at this pseudo register instead of ASTAT, so we have to
supply the right value.

Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-22 14:19:07 -04:00
Robin Getz a80d5f449d Blackfin: handle HW errors in the new "FAULT" printing code
Signed-off-by: Robin Getz <robin.getz@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
2010-05-22 14:19:07 -04:00