Remove a period from end of command-line and fix misplaced comma.
Signed-off-by: Masanori Kobayasi <zap03216@nifty.ne.jp>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
The first formal parameter of the rb_link_node() is a pointer, and the
"node" is define a data struct (pls see line 67 and line 73 in the
doc), so the actual parameter should use "&data->node".
Signed-off-by: Figo.zhang <figo.zhang@kolorific.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Support the VIRTIO_RING_F_INDIRECT_DESC feature.
This is a simple matter of changing the descriptor walking
code to operate on a struct vring_desc* and supplying it
with an indirect table if detected.
Signed-off-by: Mark McLoughlin <markmc@redhat.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The Guest only really needs to tell us about activity when we're going
to listen to the eventfd: normally, we don't want to know.
So if there are no available buffers, turn on notifications, re-check,
then wait for the Guest to notify us via the eventfd, then turn
notifications off again.
There's enough else going on that the differences are in the noise.
Before: Secs RxKicks TxKicks
1G TCP Guest->Host: 3.94 4686 32815
1M normal pings: 104 142862 1000010
1M 1k pings (-l 120): 57 142026 1000007
After:
1G TCP Guest->Host: 3.76 4691 32811
1M normal pings: 111 142859 997467
1M 1k pings (-l 120): 55 19648 501549
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rather than triggering an interrupt every time, we only trigger an
interrupt when there are no more incoming packets (or the recv queue
is full).
However, the overhead of doing the select to figure this out is
measurable: 1M pings goes from 98 to 104 seconds, and 1G Guest->Host
TCP goes from 3.69 to 3.94 seconds. It's close to the noise though.
I tested various timeouts, including reducing it as the number of
pending packets increased, timing a 1 gigabyte TCP send from Guest ->
Host and Host -> Guest (GSO disabled, to increase packet rate).
// time tcpblast -o -s 65536 -c 16k 192.168.2.1:9999 > /dev/null
Timeout Guest->Host Pkts/irq Host->Guest Pkts/irq
Before 11.3s 1.0 6.3s 1.0
0 11.7s 1.0 6.6s 23.5
1 17.1s 8.8 8.6s 26.0
1/pending 13.4s 1.9 6.6s 23.8
2/pending 13.6s 2.8 6.6s 24.1
5/pending 14.1s 5.0 6.6s 24.4
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
If we track how many buffers we've used, we can tell whether we really
need to interrupt the Guest. This happens as a side effect of
spurious notifications.
Spurious notifications happen because it can take a while before the
Host thread wakes up and sets the VRING_USED_F_NO_NOTIFY flag, and
meanwhile the Guest can more notifications.
A real fix would be to use wake counts, rather than a suppression
flag, but the practical difference is generally in the noise: the
interrupt is usually coalesced into a pending one anyway so we just
save a system call which isn't clearly measurable.
Secs Spurious IRQS
1G TCP Guest->Host: 3.93 58
1M normal pings: 100 72
1M 1k pings (-l 120): 57 492904
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Rather than sending an interrupt on every buffer, we only send an interrupt
when we're about to wait for the Guest to send us a new one. The console
input and network input still send interrupts manually, but the block device,
network and console output queues can simply rely on this logic to send
interrupts to the Guest at the right time.
The patch is cluttered by moving trigger_irq() higher in the code.
In practice, two factors make this optimization less interesting:
(1) we often only get one input at a time, even for networking,
(2) triggering an interrupt rapidly tends to get coalesced anyway.
Before: Secs RxIRQS TxIRQs
1G TCP Guest->Host: 3.72 32784 32771
1M normal pings: 99 1000004 995541
100,000 1k pings (-l 120): 5 49510 49058
After:
1G TCP Guest->Host: 3.69 32809 32769
1M normal pings: 99 1000004 996196
100,000 1k pings (-l 120): 5 52435 52361
(Note the interrupt count on 100k pings goes *up*: see next patch).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Currently lguest has three threads: the main Launcher thread, a Waker
thread, and a thread for the block device (because synchronous block
was simply too painful to bear).
The Waker selects() on all the input file descriptors (eg. stdin, net
devices, pipe to the block thread) and when one becomes readable it calls
into the kernel to kick the Launcher thread out into userspace, which
repeats the poll, services the device(s), and then tells the kernel to
release the Waker before re-entering the kernel to run the Guest.
Also, to make a slightly-decent network transmit routine, the Launcher
would suppress further network interrupts while it set a timer: that
signal handler would write to a pipe, which would rouse the Waker
which would prod the Launcher out of the kernel to check the network
device again.
Now we can convert all our virtqueues to separate threads: each one has
a separate eventfd for when the Guest pokes the device, and can trigger
interrupts in the Guest directly.
The linecount shows how much this simplifies, but to really bring it
home, here's an strace analysis of single Guest->Host ping before:
* Guest sends packet, notifies xmit vq, return control to Launcher
* Launcher clears notification flag on xmit ring
* Launcher writes packet to TUN device
writev(4, [{"\0\0\0\0\0\0\0\0\0\0", 10}, {"\366\r\224`\2058\272m\224vf\274\10\0E\0\0T\0\0@\0@\1\265"..., 98}], 2) = 108
* Launcher sets up interrupt for Guest (xmit ring is empty)
write(10, "\2\0\0\0\3\0\0\0", 8) = 0
* Launcher sets up timer for interrupt mitigation
setitimer(ITIMER_REAL, {it_interval={0, 0}, it_value={0, 505}}, NULL) = 0
* Launcher re-runs guest
pread64(10, 0xbfa5f4d4, 4, 0) ...
* Waker notices reply packet in tun device (it was in select)
select(12, [0 3 4 6 11], NULL, NULL, NULL) = 1 (in [4])
* Waker kicks Launcher out of guest:
pwrite64(10, "\3\0\0\0\1\0\0\0", 8, 0) = 0
* Launcher returns from running guest:
... = -1 EAGAIN (Resource temporarily unavailable)
* Launcher looks at input fds:
select(7, [0 3 4 6], NULL, NULL, {0, 0}) = 1 (in [4], left {0, 0})
* Launcher reads pong from tun device:
readv(4, [{"\0\0\0\0\0\0\0\0\0\0", 10}, {"\272m\224vf\274\366\r\224`\2058\10\0E\0\0T\364\26\0\0@"..., 1518}], 2) = 108
* Launcher injects guest notification:
write(10, "\2\0\0\0\2\0\0\0", 8) = 0
* Launcher rechecks fds:
select(7, [0 3 4 6], NULL, NULL, {0, 0}) = 0 (Timeout)
* Launcher clears Waker:
pwrite64(10, "\3\0\0\0\0\0\0\0", 8, 0) = 0
* Launcher reruns Guest:
pread64(10, 0xbfa5f4d4, 4, 0) = ? ERESTARTSYS (To be restarted)
* Signal comes in, uses pipe to wake up Launcher:
--- SIGALRM (Alarm clock) @ 0 (0) ---
write(8, "\0", 1) = 1
sigreturn() = ? (mask now [])
* Waker sees write on pipe:
select(12, [0 3 4 6 11], NULL, NULL, NULL) = 1 (in [6])
* Waker kicks Launcher out of Guest:
pwrite64(10, "\3\0\0\0\1\0\0\0", 8, 0) = 0
* Launcher exits from kernel:
pread64(10, 0xbfa5f4d4, 4, 0) = -1 EAGAIN (Resource temporarily unavailable)
* Launcher looks to see what fd woke it:
select(7, [0 3 4 6], NULL, NULL, {0, 0}) = 1 (in [6], left {0, 0})
* Launcher reads timeout fd, sets notification flag on xmit ring
read(6, "\0", 32) = 1
* Launcher rechecks fds:
select(7, [0 3 4 6], NULL, NULL, {0, 0}) = 0 (Timeout)
* Launcher clears Waker:
pwrite64(10, "\3\0\0\0\0\0\0\0", 8, 0) = 0
* Launcher resumes Guest:
pread64(10, "\0p\0\4", 4, 0) ....
strace analysis of single Guest->Host ping after:
* Guest sends packet, notifies xmit vq, creates event on eventfd.
* Network xmit thread wakes from read on eventfd:
read(7, "\1\0\0\0\0\0\0\0", 8) = 8
* Network xmit thread writes packet to TUN device
writev(4, [{"\0\0\0\0\0\0\0\0\0\0", 10}, {"J\217\232FI\37j\27\375\276\0\304\10\0E\0\0T\0\0@\0@\1\265"..., 98}], 2) = 108
* Network recv thread wakes up from read on tunfd:
readv(4, [{"\0\0\0\0\0\0\0\0\0\0", 10}, {"j\27\375\276\0\304J\217\232FI\37\10\0E\0\0TiO\0\0@\1\214"..., 1518}], 2) = 108
* Network recv thread sets up interrupt for the Guest
write(6, "\2\0\0\0\2\0\0\0", 8) = 0
* Network recv thread goes back to reading tunfd
13:39:42.460285 readv(4, <unfinished ...>
* Network xmit thread sets up interrupt for Guest (xmit ring is empty)
write(6, "\2\0\0\0\3\0\0\0", 8) = 0
* Network xmit thread goes back to reading from eventfd
read(7, <unfinished ...>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
This version requires that host and guest have the same PAE status.
NX cap is not offered to the guest, yet.
Signed-off-by: Matias Zabaljauregui <zabaljauregui@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
The "len" field in the used ring for virtio indicates the number of
bytes *written* to the buffer. This means the guest doesn't have to
zero the buffers in advance as it always knows the used length.
Erroneously, the console and network example code puts the length
*read* into that field. The guest ignores it, but it's wrong.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
18 months ago 5bbf89fc26 changed to loading
bzImages directly, and no longer manually ungzipping them, so we no longer
need libz.
Also, -m32 is useful for those on 64-bit platforms (and harmless on
32-bit).
Reported-by: Ron Minnich <rminnich@gmail.com>
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
2088761152 (lguest: notify on empty) introduced
lguest support for the VIRTIO_F_NOTIFY_ON_EMPTY flag, but in fact it turned on
interrupts all the time.
Because we always process one buffer at a time, the inflight count is always 0
when call trigger_irq and so we always ignore VRING_AVAIL_F_NO_INTERRUPT from
the Guest.
It should be looking to see if there are more buffers in the Guest's queue:
if it's empty, then we force an interrupt.
This makes little difference, since we usually have an empty queue; but
that's the subject of another patch.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Since the Launcher process runs the Guest, it doesn't have to be very
serious about its barriers: the Guest isn't running while we are (Guest
is UP).
Before we change to use threads to service devices, we need to fix this.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We hand the /dev/lguest fd everywhere; it's far neater to just make it
a global (it already is, in fact, hidden in the waker_fds struct).
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
We can't trust the values in the device descriptor table once the
guest has booted, so keep local copies. They could set them to
strange values then cause us to segv (they're 8 bit values, so they
can't make our pointers go too wild).
This becomes more important with the following patches which read them.
Signed-off-by: Rusty Russell <rusty@rustcorp.com.au>
Commit b00055aacd " [NET] core: add
RFC2863 operstate" defined new interface flag values. Its
documentation specified that these flags could be accessed from user
space via SIOCGIFFLAGS. However, this does not work because the new
flags do not fit in that ioctl's argument width.
Change the documentation to match the code's behavior. Also change
the source to explicitly show the truncation. This _should_ have no
effect on executable code, and did not with gcc 4.2.4 generating x86
code.
A new ioctl could be defined to return all interface flags to user
space. However, since this has been broken for three years with no
one complaining, there doesn't seem much need. They are still
accessible via netlink.
Reported-by: "Fredrik Arnerup" <fredrik.arnerup@edgeware.tv>
Signed-off-by: John Dykstra <john.dykstra1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://linux-arm.org/linux-2.6:
kmemleak: Add the corresponding MAINTAINERS entry
kmemleak: Simple testing module for kmemleak
kmemleak: Enable the building of the memory leak detector
kmemleak: Remove some of the kmemleak false positives
kmemleak: Add modules support
kmemleak: Add kmemleak_alloc callback from alloc_large_system_hash
kmemleak: Add the vmalloc memory allocation/freeing hooks
kmemleak: Add the slub memory allocation/freeing hooks
kmemleak: Add the slob memory allocation/freeing hooks
kmemleak: Add the slab memory allocation/freeing hooks
kmemleak: Add documentation on the memory leak detector
kmemleak: Add the base support
Manual conflict resolution (with the slab/earlyboot changes) in:
drivers/char/vt.c
init/main.c
mm/slab.c
* 'for-2.6.31' of git://git.kernel.dk/linux-2.6-block: (153 commits)
block: add request clone interface (v2)
floppy: fix hibernation
ramdisk: remove long-deprecated "ramdisk=" boot-time parameter
fs/bio.c: add missing __user annotation
block: prevent possible io_context->refcount overflow
Add serial number support for virtio_blk, V4a
block: Add missing bounce_pfn stacking and fix comments
Revert "block: Fix bounce limit setting in DM"
cciss: decode unit attention in SCSI error handling code
cciss: Remove no longer needed sendcmd reject processing code
cciss: change SCSI error handling routines to work with interrupts enabled.
cciss: separate error processing and command retrying code in sendcmd_withirq_core()
cciss: factor out fix target status processing code from sendcmd functions
cciss: simplify interface of sendcmd() and sendcmd_withirq()
cciss: factor out core of sendcmd_withirq() for use by SCSI error handling code
cciss: Use schedule_timeout_uninterruptible in SCSI error handling code
block: needs to set the residual length of a bidi request
Revert "block: implement blkdev_readpages"
block: Fix bounce limit setting in DM
Removed reference to non-existing file Documentation/PCI/PCI-DMA-mapping.txt
...
Manually fix conflicts with tracing updates in:
block/blk-sysfs.c
drivers/ide/ide-atapi.c
drivers/ide/ide-cd.c
drivers/ide/ide-floppy.c
drivers/ide/ide-tape.c
include/trace/events/block.h
kernel/trace/blktrace.c
This patch adds the Documentation/kmemleak.txt file with some
information about how kmemleak works.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
This patch introduces three boot options (no_cmci, dont_log_ce
and ignore_ce) to control handling for corrected errors.
The "mce=no_cmci" boot option disables the CMCI feature.
Since CMCI is a new feature so having boot controls to disable
it will be a help if the hardware is misbehaving.
The "mce=dont_log_ce" boot option disables logging for corrected
errors. All reported corrected errors will be cleared silently.
This option will be useful if you never care about corrected
errors.
The "mce=ignore_ce" boot option disables features for corrected
errors, i.e. polling timer and cmci. All corrected events are
not cleared and kept in bank MSRs.
Usually this disablement is not recommended, however it will be
a help if there are some conflict with the BIOS or hardware
monitoring applications etc., that clears corrected events in
banks instead of OS.
[ And trivial cleanup (space -> tab) for doc is included. ]
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Reviewed-by: Andi Kleen <ak@linux.intel.com>
LKML-Reference: <4A30ACDF.5030408@jp.fujitsu.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
* 'tracing-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (244 commits)
Revert "x86, bts: reenable ptrace branch trace support"
tracing: do not translate event helper macros in print format
ftrace/documentation: fix typo in function grapher name
tracing/events: convert block trace points to TRACE_EVENT(), fix !CONFIG_BLOCK
tracing: add protection around module events unload
tracing: add trace_seq_vprint interface
tracing: fix the block trace points print size
tracing/events: convert block trace points to TRACE_EVENT()
ring-buffer: fix ret in rb_add_time_stamp
ring-buffer: pass in lockdep class key for reader_lock
tracing: add annotation to what type of stack trace is recorded
tracing: fix multiple use of __print_flags and __print_symbolic
tracing/events: fix output format of user stack
tracing/events: fix output format of kernel stack
tracing/trace_stack: fix the number of entries in the header
ring-buffer: discard timestamps that are at the start of the buffer
ring-buffer: try to discard unneeded timestamps
ring-buffer: fix bug in ring_buffer_discard_commit
ftrace: do not profile functions when disabled
tracing: make trace pipe recognize latency format flag
...
* 'oprofile-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
oprofile: introduce module_param oprofile.cpu_type
oprofile: add support for Core i7 and Atom
oprofile: remove undocumented oprofile.p4force option
oprofile: re-add force_arch_perfmon option
* 'rcu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
rcu: rcu_sched_grace_period(): kill the bogus flush_signals()
rculist: use list_entry_rcu in places where it's appropriate
rculist.h: introduce list_entry_rcu() and list_first_entry_rcu()
rcu: Update RCU tracing documentation for __rcu_pending
rcu: Add __rcu_pending tracing to hierarchical RCU
RCU: make treercu be default
* 'iommu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (61 commits)
amd-iommu: remove unnecessary "AMD IOMMU: " prefix
amd-iommu: detach device explicitly before attaching it to a new domain
amd-iommu: remove BUS_NOTIFY_BOUND_DRIVER handling
dma-debug: simplify logic in driver_filter()
dma-debug: disable/enable irqs only once in device_dma_allocations
dma-debug: use pr_* instead of printk(KERN_* ...)
dma-debug: code style fixes
dma-debug: comment style fixes
dma-debug: change hash_bucket_find from first-fit to best-fit
x86: enable GART-IOMMU only after setting up protection methods
amd_iommu: fix lock imbalance
dma-debug: add documentation for the driver filter
dma-debug: add dma_debug_driver kernel command line
dma-debug: add debugfs file for driver filter
dma-debug: add variables and checks for driver filter
dma-debug: fix debug_dma_sync_sg_for_cpu and debug_dma_sync_sg_for_device
dma-debug: use sg_dma_len accessor
dma-debug: use sg_dma_address accessor instead of using dma_address directly
amd-iommu: don't free dma adresses below 512MB with CONFIG_IOMMU_STRESS
amd-iommu: don't preallocate page tables with CONFIG_IOMMU_STRESS
...
* 'futexes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
futex: fix restart in wait_requeue_pi
futex: fix restart for early wakeup in futex_wait_requeue_pi()
futex: cleanup error exit
futex: remove the wait queue
futex: add requeue-pi documentation
futex: remove FUTEX_REQUEUE_PI (non CMP)
futex: fix futex_wait_setup key handling
sparc64: extend TI_RESTART_BLOCK space by 8 bytes
futex: fixup unlocked requeue pi case
futex: add requeue_pi functionality
futex: split out futex value validation code
futex: distangle futex_requeue()
futex: add FUTEX_HAS_TIMEOUT flag to restart.futex.flags
rt_mutex: add proxy lock routines
futex: split out fixup owner logic from futex_lock_pi()
futex: split out atomic logic from futex_lock_pi()
futex: add helper to find the top prio waiter of a futex
futex: separate futex_wait_queue_me() logic from futex_wait()
* 'x86-mm-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (22 commits)
x86: fix system without memory on node0
x86, mm: Fix node_possible_map logic
mm, x86: remove MEMORY_HOTPLUG_RESERVE related code
x86: make sparse mem work in non-NUMA mode
x86: process.c, remove useless headers
x86: merge process.c a bit
x86: use sparse_memory_present_with_active_regions() on UMA
x86: unify 64-bit UMA and NUMA paging_init()
x86: Allow 1MB of slack between the e820 map and SRAT, not 4GB
x86: Sanity check the e820 against the SRAT table using e820 map only
x86: clean up and and print out initial max_pfn_mapped
x86/pci: remove rounding quirk from e820_setup_gap()
x86, e820, pci: reserve extra free space near end of RAM
x86: fix typo in address space documentation
x86: 46 bit physical address support on 64 bits
x86, mm: fault.c, use printk_once() in is_errata93()
x86: move per-cpu mmu_gathers to mm/init.c
x86: move max_pfn_mapped and max_low_pfn_mapped to setup.c
x86: unify noexec handling
x86: remove (null) in /sys kernel_page_tables
...
* 'x86-cpu-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: cpu_debug: Remove model information to reduce encoding-decoding
x86: fixup numa_node information for AMD CPU northbridge functions
x86: k8 convert node_to_k8_nb_misc() from a macro to an inline function
x86: cacheinfo: complete L2/L3 Cache and TLB associativity field definitions
x86/docs: add description for cache_disable sysfs interface
x86: cacheinfo: disable L3 ECC scrubbing when L3 cache index is disabled
x86: cacheinfo: replace sysfs interface for cache_disable feature
x86: cacheinfo: use cached K8 NB_MISC devices instead of scanning for it
x86: cacheinfo: correct return value when cache_disable feature is not active
x86: cacheinfo: use L3 cache index disable feature only for CPUs that support it
* 'sched-core-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
sched: fix typo in sched-rt-group.txt file
ftrace: fix typo about map of kernel priority in ftrace.txt file.
sched: properly define the sched_group::cpumask and sched_domain::span fields
sched, timers: cleanup avenrun users
sched, timers: move calc_load() to scheduler
sched: Don't export sched_mc_power_savings on multi-socket single core system
sched: emit thread info flags with stack trace
sched: rt: document the risk of small values in the bandwidth settings
sched: Replace first_cpu() with cpumask_first() in ILB nomination code
sched: remove extra call overhead for schedule()
sched: use group_first_cpu() instead of cpumask_first(sched_group_cpus())
wait: don't use __wake_up_common()
sched: Nominate a power-efficient ilb in select_nohz_balancer()
sched: Nominate idle load balancer from a semi-idle package.
sched: remove redundant hierarchy walk in check_preempt_wakeup
* 'x86-kbuild-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip: (46 commits)
x86, boot: add new generated files to the appropriate .gitignore files
x86, boot: correct the calculation of ZO_INIT_SIZE
x86-64: align __PHYSICAL_START, remove __KERNEL_ALIGN
x86, boot: correct sanity checks in boot/compressed/misc.c
x86: add extension fields for bootloader type and version
x86, defconfig: update kernel position parameters
x86, defconfig: update to current, no material changes
x86: make CONFIG_RELOCATABLE the default
x86: default CONFIG_PHYSICAL_START and CONFIG_PHYSICAL_ALIGN to 16 MB
x86: document new bzImage fields
x86, boot: make kernel_alignment adjustable; new bzImage fields
x86, boot: remove dead code from boot/compressed/head_*.S
x86, boot: use LOAD_PHYSICAL_ADDR on 64 bits
x86, boot: make symbols from the main vmlinux available
x86, boot: determine compressed code offset at compile time
x86, boot: use appropriate rep string for move and clear
x86, boot: zero EFLAGS on 32 bits
x86, boot: set up the decompression stack as early as possible
x86, boot: straighten out ranges to copy/zero in compressed/head*.S
x86, boot: stylistic cleanups for boot/compressed/head_64.S
...
Fixed trivial conflict in arch/x86/configs/x86_64_defconfig manually
The function graph tracer is called just "function_graph" (no trailing
"_tracer" needed).
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
LKML-Reference: <1244623722-6325-1-git-send-email-vapier@gentoo.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
* topic/oxygen:
sound: virtuoso: add Xonar Essence ST support
sound: virtuoso: enable HDAV S/PDIF input
sound: virtuoso: add another DX PCI ID
sound: oxygen: reset DMA when stream is closed
* topic/maya44:
ALSA: ice1724 - Add ESI Maya44 support
ALSA: ice1724 - Allow spec driver to create own routing controls
ALSA: ice1724 - Add PCI postint to reset sequence
ALSA: ice1724 - Clean up definitions of DMA records
ALSA: ice1724 - Check error in set_rate function
* topic/asoc: (135 commits)
ASoC: Apostrophe patrol
ASoC: codec tlv320aic23 fix bogus divide by 0 message
ASoC: fix NULL pointer dereference in soc_suspend()
ASoC: Fix build error in twl4030.c
ASoC: SSM2602: assign last substream to the master when shutting down
ASoC: Blackfin: document how anomaly 05000250 is handled
ASoC: Blackfin: set the transfer size according the ac97_frame size
ASoC: SSM2602: remove unsupported sample rates
ASoC: TWL4030: Check the interface format for 4 channel mode
ASoC: TWL4030: Use reg_cache in twl4030_init_chip
ASoC: Initialise dev for the dummy S/PDIF DAI
ASoC: Add dummy S/PDIF codec support
ASoC: correct print specifiers for unsigneds
ASoC: Modify mpc5200 AC97 driver to use V9 of spin_event_timeout()
ASoC: Switch FSL SSI DAI over to symmetric_rates
ASoC: Mark MPC5200 AC97 as BROKEN until PowerPC merge issues are resolved
ASoC: Fabric bindings for STAC9766 on the Efika
ASoC: Support for AC97 on Phytec pmc030 base board.
ASoC: AC97 driver for mpc5200
ASoC: Main rewite of the mpc5200 audio DMA code
...
All the KCONFIG_ environment variables were previously located in a
section "Environment variables in 'menuconfig'", but neither are they
restricted to 'menuconfig' nor are they all used by 'menuconfig'.
Introduce the following three sections for these variables:
* Environment variables for '*config'
* Environment variables for '{allyes/allmod/allno/rand}config'
* Environment variables for 'silentoldconfig'
Furthermore this puts MENUCONFIG_MODE next to MENUCONFIG_COLOR into a
common section "User interface options for 'menuconfig'".
Signed-off-by: Markus Heidelberg <markus.heidelberg@web.de>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
There is an error in the make syntax for one of the kbuild examples
Signed-off-by: David VomLehn <dvomlehn@cisco.com>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>
Add MAINTAINERS entry and a small text describing our stack interfaces,
how to hook the drivers, etc.
Signed-off-by: Dmitry Eremin-Solenikov <dbaryshkov@gmail.com>
Signed-off-by: Sergey Lapin <slapin@ossfans.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Added 7.1 support for MSI GX620 and jack quirk.
Reference: kernel bug#13430
http://bugzilla.kernel.org/show_bug.cgi?id=13430
Signed-off-by: David Heidelberger <d.okias@gmail.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Clarify calling context and return codes of callback methods, and
add a description of the _cmsg structure and helper functions.
Impact: documentation
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
Change the name of the Kernel CAPI exported function capi_ctr_reseted()
to something representing its purpose better.
Impact: renaming, no functional change
Signed-off-by: Tilman Schmidt <tilman@imap.cc>
Signed-off-by: David S. Miller <davem@davemloft.net>
From the perspective of most users of recent systems, disabling Host
Protected Area (HPA) can break vendor RAID formats, GPT partitions and
risks corrupting firmware or overwriting vendor system recovery tools.
Unfortunately the original (kernels < 2.6.30) behavior (unconditionally
disabling HPA and using full disk capacity) was introduced at the time
when the main use of HPA was to make the drive look small enough for the
BIOS to allow the system to boot with large capacity drives.
Thus to allow the maximum compatibility with the existing setups (using
HPA and partitioned with HPA disabled) we automically disable HPA if
any partitions overlapping HPA are detected. Additionally HPA can also
be disabled using the "nohpa" module parameter (i.e. "ide_core.nohpa=0.0"
to disable HPA on /dev/hda).
v2:
Fix ->resume HPA support.
While at it:
- remove stale "idebus=" entry from Documentation/kernel-parameters.txt
Cc: Robert Hancock <hancockrwd@gmail.com>
Cc: Frans Pop <elendil@planet.nl>
Cc: "Andries E. Brouwer" <Andries.Brouwer@cwi.nl>
Cc: Al Viro <viro@zeniv.linux.org.uk>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
[patch description was based on input from Alan Cox and Frans Pop]
Emphatically-Acked-by: Alan Cox <alan@linux.intel.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>
Merge reason: This branch was on an -rc5 base so pull almost-2.6.30
to resync with the latest upstream fixes and make sure
the combination works fine.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
This is an updated document covering the internal API for the debugfs
filesystem. Thanks to Shen Feng for suggesting that I put this text here
and noting that the old LWN version was rather out of date.
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Reported-by: Shen Feng <shen@cn.fujitsu.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
with BIOS probing only we offer a non functional headphone swith and
volume slider.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Unfortunately many patch submissions are arriving with painfully poor
patch descriptions. As a result of the discussion on LKML:
http://lkml.org/lkml/2009/4/15/296
explain how to submit a better patch description, in the (perhaps
vain) hope that maintainers won't end up having to rewrite the git
commit logs as often as they do today.
Signed-off-by: "Theodore Ts'o" <tytso@mit.edu>
Cc: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Add a couple of paragraphs to the "patch formatting" section on how patches
should be described. This text is shamelessly cribbed from suggestions
posted by Rusty Russell.
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
Randy pointed out that the Reported-By tag should be documented with the
others in SubmittingPatches.
Reported-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Jonathan Corbet <corbet@lwn.net>
On Intel platforms machine check exceptions are always broadcast to
all CPUs. This patch makes the machine check handler synchronize all
these machine checks, elect a Monarch to handle the event and collect
the worst event from all CPUs and then process it first.
This has some advantages:
- When there is a truly data corrupting error the system panics as
quickly as possible. This improves containment of corrupted
data and makes sure the corrupted data never hits stable storage.
- The panics are synchronized and do not reenter the panic code
on multiple CPUs (which currently does not handle this well).
- All the errors are reported. Currently it often happens that
another CPU happens to do the panic first, but reports useless
information (empty machine check) because the real error
happened on another CPU which came in later.
This is a big advantage on Nehalem where the 8 threads per CPU
lead to often the wrong CPU winning the race and dumping
useless information on a machine check. The problem also occurs
in a less severe form on older CPUs.
- The system can detect when no CPUs detected a machine check
and shut down the system. This can happen when one CPU is so
badly hung that that it cannot process a machine check anymore
or when some external agent wants to stop the system by
asserting the machine check pin. This follows Intel hardware
recommendations.
- This matches the recommended error model by the CPU designers.
- The events can be output in true severity order
- When a panic happens on another CPU it makes sure to be actually
be able to process the stop IPI by enabling interrupts.
The code is extremly careful to handle timeouts while waiting
for other CPUs. It can't rely on the normal timing mechanisms
(jiffies, ktime_get) because of its asynchronous/lockless nature,
so it uses own timeouts using ndelay() and a "SPINUNIT"
The timeout is configurable. By default it waits for upto one
second for the other CPUs. This can be also disabled.
From some informal testing AMD systems do not see to broadcast
machine checks, so right now it's always disabled by default on
non Intel CPUs or also on very old Intel systems.
Includes fixes from Ying Huang
Fixed a "ecception" in a comment (H.Seto)
Moved global_nwo reset later based on suggestion from H.Seto
v2: Avoid duplicate messages
[ Impact: feature, fixes long standing problems. ]
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Add some blurb about /dev/rfkill to the documentation and
fix the "transmiter" spelling error.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The new code added by this patch will make rfkill create
a misc character device /dev/rfkill that userspace can use
to control rfkill soft blocks and get status of devices as
well as events when the status changes.
Using it is very simple -- when you open it you can read
a number of times to get the initial state, and every
further read blocks (you can poll) on getting the next
event from the kernel. The same structure you read is
also used when writing to it to change the soft block of
a given device, all devices of a given type, or all
devices.
This also makes CONFIG_RFKILL_INPUT selectable again in
order to be able to test without it present since its
functionality can now be replaced by userspace entirely
and distros and users may not want the input part of
rfkill interfering with their userspace code. We will
also write a userspace daemon to handle all that and
consequently add the input code to the feature removal
schedule.
In order to have rfkilld support both kernels with and
without CONFIG_RFKILL_INPUT (or new kernels after its
eventual removal) we also add an ioctl (that only exists
if rfkill-input is present) to disable rfkill-input.
It is not very efficient, but at least gives the correct
behaviour in all cases.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This patch completely rewrites the rfkill core to address
the following deficiencies:
* all rfkill drivers need to implement polling where necessary
rather than having one central implementation
* updating the rfkill state cannot be done from arbitrary
contexts, forcing drivers to use schedule_work and requiring
lots of code
* rfkill drivers need to keep track of soft/hard blocked
internally -- the core should do this
* the rfkill API has many unexpected quirks, for example being
asymmetric wrt. alloc/free and register/unregister
* rfkill can call back into a driver from within a function the
driver called -- this is prone to deadlocks and generally
should be avoided
* rfkill-input pointlessly is a separate module
* drivers need to #ifdef rfkill functions (unless they want to
depend on or select RFKILL) -- rfkill should provide inlines
that do nothing if it isn't compiled in
* the rfkill structure is not opaque -- drivers need to initialise
it correctly (lots of sanity checking code required) -- instead
force drivers to pass the right variables to rfkill_alloc()
* the documentation is hard to read because it always assumes the
reader is completely clueless and contains way TOO MANY CAPS
* the rfkill code needlessly uses a lot of locks and atomic
operations in locked sections
* fix LED trigger to actually change the LED when the radio state
changes -- this wasn't done before
Tested-by: Alan Jenkins <alan-jenkins@tuffmail.co.uk>
Signed-off-by: Henrique de Moraes Holschuh <hmh@hmh.eng.br> [thinkpad]
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
On severe errors FAT remounts itself in read-only mode. Allow to
specify FAT fs desired behavior through 'errors' mount option:
panic, continue or remount read-only.
`mount -t [fat|vfat] -o errors=[panic,remount-ro,continue] \
<bdev> <mount point>`
This is analog to ext2 fs 'errors' mount option.
Signed-off-by: Denis Karpov <ext-denis.2.karpov@nokia.com>
Signed-off-by: OGAWA Hirofumi <hirofumi@mail.parknet.co.jp>
Add sysfs entries to the cciss driver needed for the dm/multipath tools.
A file for vendor, model, rev, and unique_id is added for each logical
drive under directory /sys/bus/pci/devices/<dev>/ccissX/cXdY. Where X =
the controller (or host) number and Y is the logical drive number.
A link from /sys/bus/pci/devices/<dev>/ccissX/cXdY/block:cciss!cXdY to
/sys/block/cciss!cXdY/device is also created. A bus is created in
/sys/bus/cciss. A link is created from the pci ccissX entry to
/sys/bus/cciss/devices/ccissX. Please consider this for inclusion.
Signed-off-by: Mike Miller <mike.miller@hp.com>
Cc: Stephen M. Cameron <scameron@beardog.cca.cpqcorp.net>
Signed-off-by: Jens Axboe <jens.axboe@oracle.com>
Short story: this laptop has 5.1 built-in speakers which you *really*
want to use (the not-so-"sub" woofer is what makes the audio above
average for a laptop), so 6-channel support is important (plus a decent
asound.conf to upmix stereo). It also has the 3 typical jacks that ought
to have a selectable mode. And it's based on ALC889, which sucks.
Rationale/explanations:
The const_channel_count stuff was added because, for a laptop like this,
you always have 6 channels available (internal speakers) but still need
to set the mode for the 3 external jacks. Therefore, the device always
needs to be in 6-channel mode but there still needs to be a mixer
control for the jack mode. You could use line/mic-in at the same time as
the 6 internal speakers, for example. You might be tempted to make it
even smarter by dynamically switching the max channel count when
headphones are plugged in (therefore muting the internal speakers and
reducing the physical channel count to the jack channel mode), but as a
user I consider this to be harmful because I want the audio to blow up
to 6 channels / upmixed as soon as I unplug the headphones, and having
opened the device while in 2-channel mode would prevent this from
working (and always making 6-channel mode available doesn't do any harm).
The hardware needs EAPD turned on and the DACs routed to the internal
speaker pins, so the patch adds those verbs.
The ALC889 CLFE and subsequent (side/aux, here unused) DACs do NOT work
by default, at least here. I wasted much time trying to talk to
Realtek/pshou about this, but they just kept sending me useless updates
to patch_realtek.c that did nothing relevant. In the end I gave up and
brute forced the issue by trying to flip every bit in the proprietary
coefficient registers, and eventually found the two magic registers that
need to be cleared to enable all DACs. I have only heard Acer users
complain, but that might be because ALC889 is pretty new and using 5.1
(and noticing the missing center/lfe channels) might not be that common.
If this is a generalized issue with all ALC889 systems then those verbs
should probably be moved to a common verb array.
The internal mic is untested and probably doesn't work.
These settings will probably work for other Acer Gemstone laptops with
the same 5.1 speaker config. When identified, those should be added to
the PCI subsystem ID list.
Signed-off-by: Hector Martin <hector@marcansoft.com>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
When using ftrace=function on the command line to trace functions
on boot up, one can not filter out functions that are commonly called.
This patch adds two new ftrace command line commands.
ftrace_notrace=function-list
ftrace_filter=function-list
Where function-list is a comma separated list of functions to filter.
The ftrace_notrace will make the functions listed not be included
in the function tracing, and ftrace_filter will only trace the functions
listed.
These two act the same as the debugfs/tracing/set_ftrace_notrace and
debugfs/tracing/set_ftrace_filter respectively.
The simple glob expressions that are allowed by the filter files can also
be used by the command line interface.
ftrace_notrace=rcu*,*lock,*spin*
Will not trace any function that starts with rcu, ends with lock, or has
the word spin in it.
Note, if the self tests are enabled, they may interfere with the filtering
set by the command lines.
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Merge reason: arch/x86/kernel/irqinit_{32,64}.c unified in irq/numa
and modified in x86/mce3; this merge resolves the conflict.
Conflicts:
arch/x86/kernel/irqinit.c
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Conflicts:
arch/mips/sibyte/bcm1480/irq.c
arch/mips/sibyte/sb1250/irq.c
Merge reason: we gathered a few conflicts plus update to latest upstream fixes.
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Add fan_max description.
Add fan limit alarm 'max_alarm' to the alarm section.
Signed-off-by: Christian Engelmayer <christian.engelmayer@frequentis.com>
Acked-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Add 'autoconf' and 'disable_ipv6' parameters to the IPv6 module.
The first controls if IPv6 addresses are autoconfigured from
prefixes received in Router Advertisements. The IPv6 loopback
(::1) and link-local addresses are still configured.
The second controls if IPv6 addresses are desired at all. No
IPv6 addresses will be added to any interfaces.
Signed-off-by: Brian Haley <brian.haley@hp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds a generic driver for SJA1000 chips on the OpenFirmware
platform bus found on embedded PowerPC systems. You need a SJA1000 node
definition in your flattened device tree source (DTS) file similar to:
can@3,100 {
compatible = "nxp,sja1000";
reg = <3 0x100 0x80>;
interrupts = <2 0>;
interrupt-parent = <&mpic>;
nxp,external-clock-frequency = <16000000>;
};
See also Documentation/powerpc/dts-bindings/can/sja1000.txt.
CC: devicetree-discuss@ozlabs.org
Signed-off-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: libps2 - better handle bad scheduler decisions
Input: usb1400_ts - fix access to "device data" in resume function
Input: multitouch - augment event semantics documentation
Input: multitouch - add tracking ID to the protocol
Fix typo about static priority's range.
Kernel Space User Space
===============================================================
0(high) to 98(low) user RT priority 99(high) to 1(low)
with SCHED_RR or SCHED_FIFO
---------------------------------------------------------------
99 sched_priority is not used in scheduling
decisions(it must be specified as 0)
---------------------------------------------------------------
100(high) to 139(low) user nice -20(high) to 19(low)
---------------------------------------------------------------
140 idle task priority
---------------------------------------------------------------
* ref) http://www.kernel.org/doc/man-pages/online/pages/man2/sched_setscheduler.2.html
Signed-off-by: GeunSik Lim <geunsik.lim@samsung.com>
CC: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Fix typo about chart to map the kernel priority to user land priorities.
* About sched_setscheduler(2)
Processes scheduled under SCHED_FIFO or SCHED_RR
can have a (user-space) static priority in the range 1 to 99.
(reference: http://www.kernel.org/doc/man-pages/online/pages/
man2/sched_setscheduler.2.html)
* From: Steven Rostedt
0 to 98 - maps to RT tasks 99 to 1 (SCHED_RR or SCHED_FIFO)
99 - maps to internal kernel threads that want to be lower than RT tasks
but higher than SCHED_OTHER tasks. Although I'm not sure if any
kernel thread actually uses this. I'm not even sure how this can be
set, because the internal sched_setscheduler function does not allow
for it.
100 to 139 - maps nice levels -20 to 19. These are not set via
sched_setscheduler, but are set via the nice system call.
140 - reserved for idle tasks.
Signed-off-by: GeunSik Lim <geunsik.lim@samsung.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <new-submission>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Document that check_interval set to 0 means no polling.
Noticed by Hidetoshi Seto
Also add a reference from boot options to the sysfs tunables
Acked-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Schedule for removal in 2.6.32
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
Signed-off-by: Hidetoshi Seto <seto.hidetoshi@jp.fujitsu.com>
Signed-off-by: H. Peter Anvin <hpa@zytor.com>
The PCM hw_ptr jiffies check results sometimes in problems when a
hardware doesn't give smooth hw_ptr updates. So far, au88x0 and some
other drivers appear not working due to this strict check.
However, this check is a nice debug tool, and the capability should be
still kept.
Hence, we disable this check now as default unless the user enables it
by setting the xrun_debug mode to the specific stream via a proc file.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound-2.6:
ALSA: hda - Add missing check of pin vref 50 and others in Realtek codecs
ALSA: hda - Add 5stack-no-fp model for STAC927x
ALSA: hda - Add forced codec-slots for ASUS W5Fm
The kmemtrace.enable kernel parameter no longer works. To enable
kmemtrace at boot-time, you must pass "ftrace=kmemtrace" instead.
[ Impact: remove obsolete kernel parameter documentation ]
Cc: Eduard - Gabriel Munteanu <eduard.munteanu@linux360.ro>
Signed-off-by: Pekka Enberg <penberg@cs.helsinki.fi>
LKML-Reference: <alpine.DEB.2.00.0905241112190.10296@rocky>
Signed-off-by: Frederic Weisbecker <fweisbec@gmail.com>
* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
x86: Remove remap percpu allocator for the time being
x86: cpa_flush_array wbinvd should be done on all CPUs
x86: bugfix wbinvd() model check instead of family check
x86: introduce noxsave boot parameter
x86, setup: revert ACPI 3 E820 extended attributes support
x86: DMI match for the Sony VGN-Z540N as it needs BIOS reboot
Pavel Machek