Highbank processors depend on the external ECME to perform voltage
management based on a requested frequency. Communication between the
A9 cores and the ECME happens over the pl320 IPC channel.
Signed-off-by: Mark Langsdorf <mark.langsdorf@calxeda.com>
Reviewed-by: Shawn Guo <shawn.guo@linaro.org>
Reviewed-by: Mike Turquette <mturquette@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Check whether we've actually already loaded acpi-cpufreq before
requesting it.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Add a helper function to return cpufreq_driver->name.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Now that the majority of x86 CPUs out there are supported by
acpi-cpufreq, we want it to load first and, in the AMD case, drop to
powernow-k8 only on K8s. If, however, both powernow-k8 and acpi-cpufreq
are built-in, the link order matters. Correct that.
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
de3ed81d74 ("[CPUFREQ] Change link order of x86 cpufreq modules")
changed cpufreq drivers link order so that powernow-k8 gets loaded first
due to earlier K8s having BIOS bugs.
However, now that acpi-cpufreq supports both AMD and Intel CPUs with HW
P-states, we want to load it first, so that cases where acpi-cpufreq and
powernow-k8 are both built-in and powernow-k8 initializing first, can be
addressed.
So, make sure that even if acpi-cpufreq gets loaded first, it errors out
on K8s and powernow-k8 can be loaded then successfully.
Signed-off-by: Matthew Garrett <mjg59@srcf.ucam.org>
References: http://lkml.kernel.org/r/20130118162347.GA31499@srcf.ucam.org
Signed-off-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When disable_cpufreq() is called some exported functions are still
being used that do not have a check for cpufreq being disabled.
Add a disabled check into cpufreq_cpu_get() to return NULL if
cpufreq is disabled this covers most of the exported functions. For
the exported functions that do not call cpufreq_cpu_get() add an
explicit check.
Signed-off-by: Dirk Brandewie <dirk.j.brandewie@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__cpufreq_remove_dev() is called on multiple occasions: cpufreq_driver
unregister and cpu removals.
Current implementation of this routine is overly complex without much need. If
the cpu to be removed is the policy->cpu, we remove the policy first and add all
other cpus again from policy->cpus and then finally call __cpufreq_remove_dev()
again to remove the cpu to be deleted. Haahhhh..
There exist a simple solution to removal of a cpu:
- Simply use the old policy structure
- update its fields like: policy->cpu, etc.
- notify any users of cpufreq, which depend on changing policy->cpu
Hence this patch, which tries to implement the above theory. It is tested well
by myself on ARM big.LITTLE TC2 SoC, which has 5 cores (2 A15 and 3 A7). Both
A15's share same struct policy and all A7's share same policy structure.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Tested-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fixes following sparse warning:
drivers/cpufreq/spear-cpufreq.c:33:5: warning: symbol 'spear_cpufreq_verify' was
not declared. Should it be static?
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is how the core works:
cpufreq_driver_unregister()
- subsys_interface_unregister()
- for_each_cpu() call cpufreq_remove_dev(), i.e. 0,1,2,3,4 when we
unregister.
cpufreq_remove_dev():
- Remove policy node
- Call cpufreq_add_dev() for next cpu, sharing mask with removed cpu.
i.e. When cpu 0 is removed, we call it for cpu 1. And when called for cpu 2,
we call it for cpu 3.
- cpufreq_add_dev() would call cpufreq_driver->init()
- init would return mask as AND of 2, 3 and 4 for cluster A7.
- cpufreq core would do online_cpu && policy->cpus
Here is the BUG(). Because cpu hasn't died but we have just unregistered
the cpufreq driver, online cpu would still have cpu 2 in it. And so thing
go bad again.
Solution: Keep cpumask of cpus that are registered with cpufreq core and clear
cpus when we get a call from subsys_interface_unregister() via
cpufreq_remove_dev().
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Because cpufreq core and governors worry only about the online cpus, if a cpu is
hot [un]plugged, we must notify governors about it, otherwise be ready to expect
something unexpected.
We already have notifiers in the form of CPUFREQ_GOV_START/CPUFREQ_GOV_STOP, we
just need to call them now.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq core doesn't manage offline cpus and if driver->init() has returned
mask including offline cpus, it may result in unwanted behavior by cpufreq core
or governors.
We need to get only online cpus in this mask. There are two places to fix this
mask, cpufreq core and cpufreq driver. It makes sense to do this at common place
and hence is done in core.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify update_sampling_rate() to check, and eventually immediately
schedule, all CPU's do_dbs_timer delayed work.
This is required in case of software coordinated CPUs, as we now have a
separate delayed work for each CPU.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify conservative timer to not resample CPU utilization if recently
sampled from another SW coordinated core.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Modify ondemand timer to not resample CPU utilization if recently
sampled from another SW coordinated core.
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch fixes a bug that occurred when we had load on a secondary CPU
and the primary CPU was sleeping. Only one sampling timer was spawned
and it was spawned as a deferred timer on the primary CPU, so when a
secondary CPU had a change in load this was not detected by the cpufreq
governor (both ondemand and conservative).
This patch make sure that deferred timers are run on all CPUs in the
case of software controlled CPUs that run on the same frequency.
Signed-off-by: Rickard Andersson <rickard.andersson@stericsson.com>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
'ret' is undefined when the function returns from the first
'if' condition. Without this patch we get the following warning:
drivers/cpufreq/exynos-cpufreq.c: In function 'exynos_target':
drivers/cpufreq/exynos-cpufreq.c:182:2: warning: 'ret' may be used uninitialized in this function [-Wuninitialized]
Suggested-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* Move sp810 header to a more generic location,
mainly to share it with arm64
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)
iQEcBAABAgAGBQJRCULAAAoJEL9jRaJfXa5PyysH/AsFbihoAGU0S7o+ggyN4S8m
5myEfbdMvgI5Hjcl/MgcVJAl6jFpDjmBH5ZPu+o8WzoP5L91C9F//kMRZqK0zATj
Y2OdMVNfVQG94bSsmjHryWF8W0RYcY2bQr0wJmgguNDpRLFsFdF3Rb58AWzG+2tP
KFxDg9u/CyhC/sv7BzoKI+J3ol5wEmv4BNMbPyjYG8L5TcBfe/IZqnl6KZ/QAw5i
QUFs3oXtT4/v8bnsxAym+VXIvjSHWs2t0CivfMyH+ZIgb3NbfJ1gIOCOJIk5XWTu
6L1yYyBBcRr60y9p4s2Nd4NxHZEB7pyZYuboUOxSmRNnEM54RT2Nkvcdon8j6Rw=
=uB7w
-----END PGP SIGNATURE-----
Merge tag 'vexpress/drivers-for-3.9' of git://git.linaro.org/people/pawelmoll/linux into next/drivers
From Pawel Moll:
Versatile Express related driver updates for 3.9:
* Move sp810 header to a more generic location,
mainly to share it with arm64
* tag 'vexpress/drivers-for-3.9' of git://git.linaro.org/people/pawelmoll/linux:
arm: Move sp810.h to include/linux/amba/
+ Linux 3.8-rc5
Signed-off-by: Olof Johansson <olof@lixom.net>
- First an ACKed MFD patch deleting the only consumer
of these cpu_is* functions outside of mach-ux500
- Introduce a new local cpu_is_u8580() in this patch
set to avoid clashing with other patch sets.
- Finally de-globalize <mach/id.h>.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.10 (GNU/Linux)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=zjvx
-----END PGP SIGNATURE-----
Merge tag 'ux500-no-idh' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/cleanup
From Linus Walleij:
Removal of the <mach/id.h> include from ux500
- First an ACKed MFD patch deleting the only consumer
of these cpu_is* functions outside of mach-ux500
- Introduce a new local cpu_is_u8580() in this patch
set to avoid clashing with other patch sets.
- Finally de-globalize <mach/id.h>.
* tag 'ux500-no-idh' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ARM: ux500: de-globalize <mach/id.h>
ARM: ux500: Introduce cpu_is_u8580()
mfd: prcmu: delete pin control helpers
Signed-off-by: Olof Johansson <olof@lixom.net>
This removes the file <mach/id.h> from the global kernel include
scope, making it a pure mach-ux500 detail. All ASIC specifics
needed by drivers shall henceforth be passed from either platform
data or the device tree.
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
* depends/cleanup: (375 commits)
ARM: at91: fix board-rm9200-dt after sys_timer conversion
clocksource: use clockevents_config_and_register() where possible
ARM: use clockevents_config_and_register() where possible
clockevents: export clockevents_config_and_register for module use
timer: vt8500: Move timer code to drivers/clocksource
irqchip: Move ARM vic.h to include/linux/irqchip/arm-vic.h
ARM: picoxcell: use common irqchip_init function
ARM: spear: use common irqchip_init function
irqchip: Move ARM VIC to drivers/irqchip
ARM: samsung: remove unused tick.h
ARM: remove unneeded vic.h includes
ARM: remove mach .handle_irq for VIC users
ARM: VIC: set handle_arch_irq in VIC initialization
ARM: VIC: shrink down vic.h
irqchip: Move ARM gic.h to include/linux/irqchip/arm-gic.h
ARM: use common irqchip_init for GIC init
irqchip: Move ARM GIC to drivers/irqchip
ARM: remove mach .handle_irq for GIC users
ARM: GIC: set handle_arch_irq in GIC initialization
ARM: GIC: remove direct use of gic_raise_softirq
...
The text in Documentation said it would be removed in 2.6.41;
the text in the Kconfig said removal in the 3.1 release. Either
way you look at it, we are well past both, so push it off a cliff.
Note that the POWER_CSTATE and the POWER_PSTATE are part of the
legacy tracing API. Remove all tracepoints which use these flags.
As can be seen from context, most already have a trace entry via
trace_cpu_idle anyways.
Also, the cpufreq/cpufreq.c PSTATE one is actually unpaired, as
compared to the CSTATE ones which all have a clear start/stop.
As part of this, the trace_power_frequency also becomes orphaned,
so it too is deleted.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
exynos_cpufreq_scale function returns signed value which was
assigned to an unsigned variable and checked for negative value which
is always false. Hence make it signed.
Fixes the following smatch warnings:
drivers/cpufreq/exynos-cpufreq.c:83 exynos_cpufreq_scale() warn: unsigned 'old_index' is never less than zero.
drivers/cpufreq/exynos-cpufreq.c:89 exynos_cpufreq_scale() warn: unsigned 'index' is never less than zero.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The acpi core will call request_module("acpi-cpufreq") on subsystem init,
but this will fail if the module isn't available at that stage of boot.
Add some module aliases to ensure that udev can load the module on Intel
and AMD systems with the appropriate feature bits - I /think/ that this
will also work on VIA systems, but haven't verified that.
References: http://lkml.kernel.org/r/1448223.sdUJnNSRz4@vostro.rjw.lan
Signed-off-by: Matthew Garrett <matthew.garrett@nebula.com>
Tested-by: Leonid Isaev <lisaev@umail.iu.edu>
Acked-by: Borislav Petkov <bp@suse.de>
Cc: 3.7+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
OPP pointer is RCU protected, hence after finding it, de-reference
also should be protected with the same RCU context else the OPP
pointer may become invalid.
Reported-by: Jack Mitchell <jack@embed.me.uk>
Tested-by: Alexander Holler <holler@ahsoftware.de>
Tested-by: Jack Mitchell <jack@embed.me.uk>
Acked-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
OPP pointer is RCU protected, hence after finding it, de-reference
also should be protected with the same RCU context else the OPP
pointer may become invalid.
Reported-by: Alexander Holler <holler@ahsoftware.de>
Tested-by: Alexander Holler <holler@ahsoftware.de>
Acked-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Boot_freq is for saving booting freq. But exynos_cpufreq_cpu_init
is called in hotplug. If boot_freq is existed in exynos_cpufreq_cpu_init,
boot_freq could be changed.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add freq_attr attribute to show list of available frequencies.
Signed-off-by: Donggeun Kim <dg77.kim@samsung.com>
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: KyungMin Park <kyungmin.park@samsung.com>
Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org>
Reviewed-by: Amit Daniel Kachhap<amit.daniel@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Andreas reports in https://bugzilla.kernel.org/show_bug.cgi?id=51741
that with his Gentoo config, acpi-cpufreq wasn't enabled and
powernow-k8 couldn't handoff properly to acpi-cpufreq leading to
running without P-state support (i.e., cores are constantly in P0).
To alleaviate that, we need to make powernow-k8 depend on acpi-cpufreq
so that acpi-cpufreq is always present.
References: https://bugzilla.kernel.org/show_bug.cgi?id=51741
Reported-by: Andreas <linuxuser330250@gmx.net>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: 3.7+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The CONFIG_EXPERIMENTAL config item has not carried much meaning for a
while now and is almost always enabled by default. As agreed during the
Linux kernel summit, remove it from any "depends on" lines in Kconfigs.
Signed-off-by: Kees Cook <keescook@chromium.org>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
As ux500 is being converted to timer based delay loops, and the timer
used is not depending on CPUs clock frequency, set cpufreq_driver flag
CPUFREQ_CONST_LOOPS to prevent cpufreq rescaling loops_for_jiffies.
Acked-by: John Stultz <john.stultz@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Real simple patch to extend the ST-Ericsson copyright date and
remove unnecessary extra commented lines.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Some minor code cleanup and some minor changes to printed
error messages.
Signed-off-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
The armss clock shall only be fetched at probe thus move this here.
Same thing goes for the printing of the available frequencies.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
This driver doesn't only handle cpufreq functionality for the
db8500 anymore. There are new variants which rely on it too.
Let's make the name a bit more generic.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Since commit 2aacdff entitled "cpufreq: Move common part from governors
to separate file", whenever the drivers that depend on this new file
(cpufreq_ondemand or cpufreq_conservative) are built as modules, a new
module named cpufreq_governor is created because the Makefile includes
cpufreq_governor.o twice. As drivers/cpufreq/cpufreq_governor.c contains no
MODULE directives, the resulting module has no license specified, which
results in logging of a "module license 'unspecified' taints kernel". In
addition, a number of globals are exported GPL only, and are therefore
not available. This fix establishes a new boolean configuration variable
that forces cpufreq_governor.o to be linked into the kernel whenever
either cpufreq_ondemand or cpufreq_conservative is selected.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This is only solution I can think of. User decides if he wants this
driver on his machine. I don't have enough knowledge and time to find
the reason why same code works on some machines and doesn't on others
which use the same, or very similar, chipset and processor.
Signed-off-by: Rafał Bilski <rafalbilski@interia.pl>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This patch forces complete struct cpufreq_stats allocation for all cpus before
registering CPUFREQ_TRANSITION_NOTIFIER notifier, otherwise in some conditions
cpufreq_stat_notifier_trans() can be called in the middle of stats allocation,
in this case cpufreq_stats_table already exists, but stat->freq_table is NULL.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@openvz.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Split exynos_target function into exynos_target & exynos_cpufreq_scale.
The exynos_cpufreq_scale changes the voltage & frequency.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
If old & new freq have the same frequency, no need to call
cpufreq notifier & regulator function.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The variable 'max_support_idx, min_support_idx, pm_lock_idx"
are never used, so remove the unused variable.
Signed-off-by: Jonghwan Choi <jhbird.choi@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
* Introduction of device PM QoS flags.
* ACPI device power management update allowing subsystems other than
PCI to use it more easily.
* ACPI device enumeration rework allowing additional kinds of devices
to be enumerated via ACPI. From Mika Westerberg, Adrian Hunter,
Mathias Nyman, Andy Shevchenko, and Rafael J. Wysocki.
* ACPICA update to version 20121018 from Bob Moore and Lv Zheng.
* ACPI memory hotplug update from Wen Congyang and Yasuaki Ishimatsu.
* Introduction of acpi_handle_<level>() messaging macros and ACPI-based CPU
hot-remove support from Toshi Kani.
* ACPI EC updates from Feng Tang.
* cpufreq updates from Viresh Kumar, Fabio Baltieri and others.
* cpuidle changes to quickly notice governor prediction failure from
Youquan Song.
* Support for using multiple cpuidle drivers at the same time and cpuidle
cleanups from Daniel Lezcano.
* devfreq updates from Nishanth Menon and others.
* cpupower update from Thomas Renninger.
* Fixes and small cleanups all over the place.
--
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.19 (GNU/Linux)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=6OEP
-----END PGP SIGNATURE-----
Merge tag 'pm+acpi-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
- Introduction of device PM QoS flags.
- ACPI device power management update allowing subsystems other than
PCI to use it more easily.
- ACPI device enumeration rework allowing additional kinds of devices
to be enumerated via ACPI. From Mika Westerberg, Adrian Hunter,
Mathias Nyman, Andy Shevchenko, and Rafael J. Wysocki.
- ACPICA update to version 20121018 from Bob Moore and Lv Zheng.
- ACPI memory hotplug update from Wen Congyang and Yasuaki Ishimatsu.
- Introduction of acpi_handle_<level>() messaging macros and ACPI-based
CPU hot-remove support from Toshi Kani.
- ACPI EC updates from Feng Tang.
- cpufreq updates from Viresh Kumar, Fabio Baltieri and others.
- cpuidle changes to quickly notice governor prediction failure from
Youquan Song.
- Support for using multiple cpuidle drivers at the same time and
cpuidle cleanups from Daniel Lezcano.
- devfreq updates from Nishanth Menon and others.
- cpupower update from Thomas Renninger.
- Fixes and small cleanups all over the place.
* tag 'pm+acpi-for-3.8-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (196 commits)
mmc: sdhci-acpi: enable runtime-pm for device HID INT33C6
ACPI: add Haswell LPSS devices to acpi_platform_device_ids list
ACPI: add documentation about ACPI 5 enumeration
pnpacpi: fix incorrect TEST_ALPHA() test
ACPI / PM: Fix header of acpi_dev_pm_detach() in acpi.h
ACPI / video: ignore BIOS initial backlight value for HP Folio 13-2000
ACPI : do not use Lid and Sleep button for S5 wakeup
ACPI / PNP: Do not crash due to stale pointer use during system resume
ACPI / video: Add "Asus UL30VT" to ACPI video detect blacklist
ACPI: do acpisleep dmi check when CONFIG_ACPI_SLEEP is set
spi / ACPI: add ACPI enumeration support
gpio / ACPI: add ACPI support
PM / devfreq: remove compiler error with module governors (2)
cpupower: IvyBridge (0x3a and 0x3e models) support
cpupower: Provide -c param for cpupower monitor to schedule process on all cores
cpupower tools: Fix warning and a bug with the cpu package count
cpupower tools: Fix malloc of cpu_info structure
cpupower tools: Fix issues with sysfs_topology_read_file
cpupower tools: Fix minor warnings
cpupower tools: Update .gitignore for files created in the debug directories
...
fixes for existing platforms as well as new ports for some ARM
platforms. In addition there are new clk drivers for audio devices and
MFDs.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=GoXf
-----END PGP SIGNATURE-----
Merge tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux
Pull clock framework changes from Mike Turquette:
"The common clock framework changes for 3.8 are comprised of lots of
fixes for existing platforms as well as new ports for some ARM
platforms. In addition there are new clk drivers for audio devices
and MFDs."
Fix up trivial conflict in <linux/clk-provider.h> (removal of 'inline'
clashing with return type fixes)
* tag 'clk-for-linus' of git://git.linaro.org/people/mturquette/linux: (51 commits)
MAINTAINERS: bad email address for Mike Turquette
clk: introduce optional disable_unused callback
clk: ux500: fix bit error
clk: clock multiplexers may register out of order
clk: ux500: Initial support for abx500 clock driver
CLK: SPEAr: Remove unused dummy apb_pclk
CLK: SPEAr: Correct index scanning done for clock synths
CLK: SPEAr: Update clock rate table
CLK: SPEAr: Add missing clocks
CLK: SPEAr: Set CLK_SET_RATE_PARENT for few clocks
CLK: SPEAr13xx: fix parent names of multiple clocks
CLK: SPEAr13xx: Fix mux clock names
CLK: SPEAr: Fix dev_id & con_id for multiple clocks
clk: move IM-PD1 clocks to drivers/clk
clk: make ICST driver handle the VCO registers
clk: add GPLv2 headers to the Versatile clock files
clk: mxs: Use a better name for the USB PHY clock
clk: spear: Add stub functions for spear3[0|1|2]0_clk_init()
CLK: clk-twl6040: fix return value check in twl6040_clk_probe()
clk: ux500: Register nomadik keypad clock lookups for u8500
...
Fix cpufreq_gov_ondemand to skip CPU where another governor is used.
The bug present itself as NULL pointer access on the mutex_lock() call,
an can be reproduced on an SMP machine by setting the default governor
to anything other than ondemand, setting a single CPU's governor to
ondemand, then changing the sample rate by writing on:
> /sys/devices/system/cpu/cpufreq/ondemand/sampling_rate
Backtrace:
Nov 26 17:36:54 balto kernel: [ 839.585241] BUG: unable to handle kernel NULL pointer dereference at (null)
Nov 26 17:36:54 balto kernel: [ 839.585311] IP: [<ffffffff8174e082>] __mutex_lock_slowpath+0xb2/0x170
[snip]
Nov 26 17:36:54 balto kernel: [ 839.587005] Call Trace:
Nov 26 17:36:54 balto kernel: [ 839.587030] [<ffffffff8174da82>] mutex_lock+0x22/0x40
Nov 26 17:36:54 balto kernel: [ 839.587067] [<ffffffff81610b8f>] store_sampling_rate+0xbf/0x150
Nov 26 17:36:54 balto kernel: [ 839.587110] [<ffffffff81031e9c>] ? __do_page_fault+0x1cc/0x4c0
Nov 26 17:36:54 balto kernel: [ 839.587153] [<ffffffff813309bf>] kobj_attr_store+0xf/0x20
Nov 26 17:36:54 balto kernel: [ 839.587192] [<ffffffff811bb62d>] sysfs_write_file+0xcd/0x140
Nov 26 17:36:54 balto kernel: [ 839.587234] [<ffffffff8114c12c>] vfs_write+0xac/0x180
Nov 26 17:36:54 balto kernel: [ 839.587271] [<ffffffff8114c472>] sys_write+0x52/0xa0
Nov 26 17:36:54 balto kernel: [ 839.587306] [<ffffffff810321ce>] ? do_page_fault+0xe/0x10
Nov 26 17:36:54 balto kernel: [ 839.587345] [<ffffffff81751202>] system_call_fastpath+0x16/0x1b
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
SPEAr is an ARM based family of SoCs. This patch adds in support of cpufreq
driver for SPEAr SoCs. It is supported via DT only and so bindings are present
in binding document.
Signed-off-by: Deepak Sikri <deepak.sikri@st.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
This change was made by commit 8636fd2 (cpufreq: fix jiffies/cputime
mixup in conservative/ondemand governors) before, but then it has
been reverted inadvertently by commit 4471a34 (cpufreq: governors:
remove redundant code).
The changelog of commit 8636fd2's says:
The function get_cpu_idle_time_jiffy in both the conservative and
ondemand governors use jiffies_to_usecs to convert a cputime value
to usecs which gives the wrong value on architectures where cputime
and jiffies use different units. Only matters if NO_HZ is
disabled, since otherwise get_cpu_idle_time_us should already
return a valid value, and get_cpu_idle_time_jiffy isn't actually
called.
Since now we have only one common get_cpu_idle_time_jiffy() used by
both governors in question, modify it along the lines of commit
8636fd2 to restore the correct behavior.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Restore the correct delay value for ondemand's od_dbs_timer, as it was
changed erroneously in commit 83f0e55 (cpufreq: governors: remove
redundant code).
Signed-off-by: Fabio Baltieri <fabio.baltieri@linaro.org>
Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Fixes following sparse error.
drivers/cpufreq/exynos-cpufreq.c:34:5: warning: symbol
'exynos_verify_speed' was not declared. Should it be static?
drivers/cpufreq/exynos-cpufreq.c:40:14: warning: symbol
'exynos_getspeed' was not declared. Should it be static?
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
On Exynos SoCs all cores share the same frequency setting, so changing
frequency of one core will affect rest of cores.
This patch modifies the exynos-cpufreq driver to inform cpufreq core
about this behavior and broadcast frequency change notifications for all
cores.
Signed-off-by: Tomasz Figa <t.figa@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CONFIG_HOTPLUG is going away as an option so __devexit is no
longer needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CONFIG_HOTPLUG is going away as an option so __devinit is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
CONFIG_HOTPLUG is going away as an option so __devexit_p is no longer
needed.
Signed-off-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Remove an unnecessary initializer for the 'ret' variable in
__cpufreq_set_policy().
[rjw: Modified the subject and changelog slightly.]
Signed-off-by: Jingoo Han <jg1.han@samsung.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
__cpufreq_driver_target() must not pass target frequency beyond the
limits of current policy.
Today most of cpufreq platform drivers are doing this check in their
target routines. Why not move it to __cpufreq_driver_target()?
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Avoid calling cpufreq driver's target() routine if new frequency is same as
policies current frequency.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
cpufreq_disabled() is a local function, so should be marked static.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There were few sparse warnings due to mismatch of type on function arguments.
Two types were used u64 and cputime64_t. Both are actually u64, so use u64 only.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Initially ondemand governor was written and then using its code conservative
governor is written. It used a lot of code from ondemand governor, but copy of
code was created instead of using the same routines from both governors. Which
increased code redundancy, which is difficult to manage.
This patch is an attempt to move common part of both the governors to
cpufreq_governor.c file to come over above mentioned issues.
This shouldn't change anything from functionality point of view.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
There is no need to do cpufreq_get_cpu() and cpufreq_put_cpu() for drivers that
don't support getavg() routine.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
The function get_cpu_idle_time_jiffy in both the conservative and
ondemand governors use jiffies_to_usecs to convert a cputime value to
usecs which gives the wrong value on architectures where cputime and
jiffies use different units. Only matters if NO_HZ is disabled, since
otherwise get_cpu_idle_time_us should already return a valid value, and
get_cpu_idle_time_jiffy isn't actually called.
Signed-off-by: Andreas Schwab <schwab@linux-m68k.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
With debug options on, it is difficult to locate cpufreq core's debug prints.
Fix this by prefixing debug prints with KBUILD_MODNAME.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Multiple cpufreq governers have defined similar get_cpu_idle_time_***()
routines. These routines must be moved to some common place, so that all
governors can use them.
So moving them to cpufreq_governor.c, which seems to be a better place for
keeping these routines.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Arrays for governer and driver name are of size CPUFREQ_NAME_LEN or 16.
i.e. 15 bytes for name and 1 for trailing '\0'.
When cpufreq driver print these names (for sysfs), it includes '\n' or ' ' in
the fmt string and still passes length as CPUFREQ_NAME_LEN. If the driver or
governor names are using all 15 fields allocated to them, then the trailing '\n'
or ' ' will never be printed. And so commands like:
root@linaro-developer# cat /sys/devices/system/cpu/cpu0/cpufreq/scaling_driver
will print something like:
cpufreq_foodrvroot@linaro-developer#
Fix this by increasing print length by one character.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
show_bios_limit is mistakenly written as show_scaling_driver in a comment
describing purpose of show_bios_limit() routine.
Fix it.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Using the armss clk to update the frequency makes the driver no more
directly dependant on the prmcu API.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
By fetching the table as platform data we do not need the internally
hardcoded cpufreq table anymore.
Moreover the corresponding arm_opp idx2opp table, used for mapping
frequency to correct opp bits is also removed. This due to that the
opp bits is put directly in the index field of the cpufreq table.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
To fetch the mfd child device we register the cpufreq driver
as a platform driver.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jonas Aaberg <jonas.aberg@stericsson.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
Change the Andreas' email address in drivers/cpufreq/powernow-k8.c.
Signed-off-by: Andreas Herrmann <herrmann.der.user@googlemail.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
When system enters sleep, non-boot CPUs will be disabled.
Cpufreq stats sysfs is created when the CPU is up, but it is not
freed when the CPU is going down. This will cause memory leak.
Signed-off-by: xiaobing tu <xiaobing.tu@intel.com>
Signed-off-by: guifang tang <guifang.tang@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
OMAP PM core code has moved to using the existing, generic CPU devices
for attaching OPPs, so the CPUfreq driver can now use the generic
get_cpu_device() API instead of the OMAP-specific omap_device API.
This allows us to remove the last <plat/*> include from this driver.
Cc: Paul Walmsley <paul@pwsan.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Kevin Hilman <khilman@ti.com>
OMAP core code now has SoC-independent clock alias for the scalable
CPU clock. Using it means driver is SoC independent and will work for
AM3xxx SoCs as well as OMAP1/3/4.
While here, remove some unnecessary plat/ includes that are
interfering with multi-subarch ARM kernels.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated already changed clock aliases]
Signed-off-by: Tony Lindgren <tony@atomide.com>
[khilman@ti.com: minor shortlog/changelog updates]
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Kevin Hilman <khilman@ti.com>
The <plat/*.h> headers are going away, and this one is not used. remove it.
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Ensure the clock rate that will be used is a valid one before
attempting to scale the voltage. Currently the driver assumes it has
a valid frequency from the OPP table, but boards using different
system oscillators might not have exact matches with the OPP table,
and result in a failing call to clk_set_rate().
This is particularily bad because the voltage may be scaled even
though the frequency is not. This will obviously lead to some
unpredictable behavior, especially if the frequency is high and
the voltage is dropped.
Thanks to Joni Lapilainen for reporting crashes seen on 3430/n900.
Reported-by: Joni Lapilainen <joni.lapilainen@gmail.com>
Acked-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Kevin Hilman <khilman@ti.com>
* Improved system suspend/resume and runtime PM handling for the SH TMU, CMT
and MTU2 clock event devices (also used by ARM/shmobile).
* Generic PM domains framework extensions related to cpuidle support and
domain objects lookup using names.
* ARM/shmobile power management updates including improved support for the
SH7372's A4S power domain containing the CPU core.
* cpufreq changes related to AMD CPUs support from Matthew Garrett, Andre
Przywara and Borislav Petkov.
* cpu0 cpufreq driver from Shawn Guo.
* cpufreq governor fixes related to the relaxing of limit from Michal Pecio.
* OMAP cpufreq updates from Axel Lin and Richard Zhao.
* cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
* Runtime PM core updates related to the interactions with the system suspend
core from Alan Stern and Kevin Hilman.
* Wakeup sources modification allowing more helper functions to be called from
interrupt context from John Stultz and additional diagnostic code from Todd
Poynor.
* System suspend error code path fix from Feng Hong.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.18 (GNU/Linux)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=rbCk
-----END PGP SIGNATURE-----
Merge tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael J Wysocki:
- Improved system suspend/resume and runtime PM handling for the SH
TMU, CMT and MTU2 clock event devices (also used by ARM/shmobile).
- Generic PM domains framework extensions related to cpuidle support
and domain objects lookup using names.
- ARM/shmobile power management updates including improved support for
the SH7372's A4S power domain containing the CPU core.
- cpufreq changes related to AMD CPUs support from Matthew Garrett,
Andre Przywara and Borislav Petkov.
- cpu0 cpufreq driver from Shawn Guo.
- cpufreq governor fixes related to the relaxing of limit from Michal
Pecio.
- OMAP cpufreq updates from Axel Lin and Richard Zhao.
- cpuidle ladder governor fixes related to the disabling of states from
Carsten Emde and me.
- Runtime PM core updates related to the interactions with the system
suspend core from Alan Stern and Kevin Hilman.
- Wakeup sources modification allowing more helper functions to be
called from interrupt context from John Stultz and additional
diagnostic code from Todd Poynor.
- System suspend error code path fix from Feng Hong.
Fixed up conflicts in cpufreq/powernow-k8 that stemmed from the
workqueue fixes conflicting fairly badly with the removal of support for
hardware P-state chips. The changes were independent but somewhat
intertwined.
* tag 'pm-for-3.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (76 commits)
Revert "PM QoS: Use spinlock in the per-device PM QoS constraints code"
PM / Runtime: let rpm_resume() succeed if RPM_ACTIVE, even when disabled, v2
cpuidle: rename function name "__cpuidle_register_driver", v2
cpufreq: OMAP: Check IS_ERR() instead of NULL for omap_device_get_by_hwmod_name
cpuidle: remove some empty lines
PM: Prevent runtime suspend during system resume
PM QoS: Use spinlock in the per-device PM QoS constraints code
PM / Sleep: use resume event when call dpm_resume_early
cpuidle / ACPI : move cpuidle_device field out of the acpi_processor_power structure
ACPI / processor: remove pointless variable initialization
ACPI / processor: remove unused function parameter
cpufreq: OMAP: remove loops_per_jiffy recalculate for smp
sections: fix section conflicts in drivers/cpufreq
cpufreq: conservative: update frequency when limits are relaxed
cpufreq / ondemand: update frequency when limits are relaxed
properly __init-annotate pm_sysrq_init()
cpufreq: Add a generic cpufreq-cpu0 driver
PM / OPP: Initialize OPP table from device tree
ARM: add cpufreq transiton notifier to adjust loops_per_jiffy for smp
cpufreq: Remove support for hardware P-state chips from powernow-k8
...
Pull workqueue changes from Tejun Heo:
"This is workqueue updates for v3.7-rc1. A lot of activities this
round including considerable API and behavior cleanups.
* delayed_work combines a timer and a work item. The handling of the
timer part has always been a bit clunky leading to confusing
cancelation API with weird corner-case behaviors. delayed_work is
updated to use new IRQ safe timer and cancelation now works as
expected.
* Another deficiency of delayed_work was lack of the counterpart of
mod_timer() which led to cancel+queue combinations or open-coded
timer+work usages. mod_delayed_work[_on]() are added.
These two delayed_work changes make delayed_work provide interface
and behave like timer which is executed with process context.
* A work item could be executed concurrently on multiple CPUs, which
is rather unintuitive and made flush_work() behavior confusing and
half-broken under certain circumstances. This problem doesn't
exist for non-reentrant workqueues. While non-reentrancy check
isn't free, the overhead is incurred only when a work item bounces
across different CPUs and even in simulated pathological scenario
the overhead isn't too high.
All workqueues are made non-reentrant. This removes the
distinction between flush_[delayed_]work() and
flush_[delayed_]_work_sync(). The former is now as strong as the
latter and the specified work item is guaranteed to have finished
execution of any previous queueing on return.
* In addition to the various bug fixes, Lai redid and simplified CPU
hotplug handling significantly.
* Joonsoo introduced system_highpri_wq and used it during CPU
hotplug.
There are two merge commits - one to pull in IRQ safe timer from
tip/timers/core and the other to pull in CPU hotplug fixes from
wq/for-3.6-fixes as Lai's hotplug restructuring depended on them."
Fixed a number of trivial conflicts, but the more interesting conflicts
were silent ones where the deprecated interfaces had been used by new
code in the merge window, and thus didn't cause any real data conflicts.
Tejun pointed out a few of them, I fixed a couple more.
* 'for-3.7' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq: (46 commits)
workqueue: remove spurious WARN_ON_ONCE(in_irq()) from try_to_grab_pending()
workqueue: use cwq_set_max_active() helper for workqueue_set_max_active()
workqueue: introduce cwq_set_max_active() helper for thaw_workqueues()
workqueue: remove @delayed from cwq_dec_nr_in_flight()
workqueue: fix possible stall on try_to_grab_pending() of a delayed work item
workqueue: use hotcpu_notifier() for workqueue_cpu_down_callback()
workqueue: use __cpuinit instead of __devinit for cpu callbacks
workqueue: rename manager_mutex to assoc_mutex
workqueue: WORKER_REBIND is no longer necessary for idle rebinding
workqueue: WORKER_REBIND is no longer necessary for busy rebinding
workqueue: reimplement idle worker rebinding
workqueue: deprecate __cancel_delayed_work()
workqueue: reimplement cancel_delayed_work() using try_to_grab_pending()
workqueue: use mod_delayed_work() instead of __cancel + queue
workqueue: use irqsafe timer for delayed_work
workqueue: clean up delayed_work initializers and add missing one
workqueue: make deferrable delayed_work initializer names consistent
workqueue: cosmetic whitespace updates for macro definitions
workqueue: deprecate system_nrt[_freezable]_wq
workqueue: deprecate flush[_delayed]_work_sync()
...
omap_device_get_by_hwmod_name() returns ERR_PTR on error.
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Pull workqueue / powernow-k8 fix from Tejun Heo:
"This is the fix for the bug where cpufreq/powernow-k8 was tripping
BUG_ON() in try_to_wake_up_local() by migrating workqueue worker to a
different CPU.
https://bugzilla.kernel.org/show_bug.cgi?id=47301
As discussed, the fix is now two parts - one to reimplement
work_on_cpu() so that it doesn't create a new kthread each time and
the actual fix which makes powernow-k8 use work_on_cpu() instead of
performing manual migration.
While pretty late in the merge cycle, both changes are on the safer
side. Jiri and I verified two existing users of work_on_cpu() and
Duncan confirmed that the powernow-k8 fix survived about 18 hours of
testing."
* 'for-3.6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
cpufreq/powernow-k8: workqueue user shouldn't migrate the kworker to another CPU
workqueue: reimplement work_on_cpu() using system_wq
powernowk8_target() runs off a per-cpu work item and if the
cpufreq_policy->cpu is different from the current one, it migrates the
kworker to the target CPU by manipulating current->cpus_allowed. The
function migrates the kworker back to the original CPU but this is
still broken. Workqueue concurrency management requires the kworkers
to stay on the same CPU and powernowk8_target() ends up triggerring
BUG_ON(rq != this_rq()) in try_to_wake_up_local() if it contends on
fidvid_mutex and sleeps.
It is unclear why this bug is being reported now. Duncan says it
appeared to be a regression of 3.6-rc1 and couldn't reproduce it on
3.5. Bisection seemed to point to 63d95a91 "workqueue: use @pool
instead of @gcwq or @cpu where applicable" which is an non-functional
change. Given that the reproduce case sometimes took upto days to
trigger, it's easy to be misled while bisecting. Maybe something made
contention on fidvid_mutex more likely? I don't know.
This patch fixes the bug by using work_on_cpu() instead if @pol->cpu
isn't the same as the current one. The code assumes that
cpufreq_policy->cpu is kept online by the caller, which Rafael tells
me is the case.
stable: ed48ece27c ("workqueue: reimplement work_on_cpu() using
system_wq") should be applied before this; otherwise, the
behavior could be horrible.
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Duncan <1i5t5.duncan@cox.net>
Tested-by: Duncan <1i5t5.duncan@cox.net>
Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Andreas Herrmann <andreas.herrmann3@amd.com>
Cc: stable@vger.kernel.org
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=47301
With ARM smp common code recalculating loops_per_jiffy in a cpufreq
transiton notifier call, the loops_per_jiffy recalculate in omap-cpufreq
driver becomes redundant. Remove it.
Signed-off-by: Richard Zhao <richard.zhao@freescale.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Kevin Hilman <khilman@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reevaluate CPU load and update frequency immediately whenever limits
are changed. Currently conservative doesn't do that when limits are
relaxed, wasting power on systems with relatively low sampling rate.
Signed-off-by: Michal Pecio <mpecio@nvidia.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Reevaluate CPU load and update frequency immediately whenever limits
are changed. Currently ondemand doesn't do that when limits are
relaxed, wasting power on systems with relatively low sampling rate.
Signed-off-by: Michal Pecio <mpecio@nvidia.com>
Reviewed-by: Thomas Renninger <trenn@suse.de>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
It adds a generic cpufreq driver for CPU0 frequency management based on
clk, regulator, OPP and device tree support. It can support both
uniprocessor (UP) and those symmetric multiprocessor (SMP) systems which
share clock and voltage across all CPUs.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Tested-by: AnilKumar Ch <anilkumar@ti.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
These chips are now supported by acpi-cpufreq, so we can delete all the
code handling them.
Andre: Tighten the deprecation warning message. Trigger load of
acpi-cpufreq and let the load of the module finally fail.
This avoids the problem of users ending up without any cpufreq support
after the transition.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The powernow-k8 driver supported a sysfs knob called "cpb", which was
instantiated per CPU, but actually acted globally for the whole
system. To keep some compatibility with this feature, we re-introduce
this behavior here, but:
a) only enable it on AMD CPUs and
b) protect it with a Kconfig switch
I'd like to consider this feature obsolete. Lets keep it around for
some kernel versions and then phase it out.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
One feature present in powernow-k8 that isn't present in acpi-cpufreq
is support for enabling or disabling AMD's core performance boost
technology. This patch adds support to acpi-cpufreq, but also
includes support for Intel's dynamic acceleration.
The original boost disabling sysfs file was per CPU, but acted
globally. Also the naming (cpb) was at least not intuitive.
So lets introduce a single file simply called "boost", which sits
once in /sys/devices/system/cpu/cpufreq.
This should be the only way of using this feature, so add
documentation about the rationale and the usage.
A following patch will re-introduce the cpb knob for compatibility
reasons on AMD CPUs.
Per-CPU boost switching is possible, but not trivial and is thus
postponed to a later patch series.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
powernow-k8 is quite prematurely crying Hooray and outputs diagnostic
messages, although the actual initialization can still fail.
Since now we may have acpi-cpufreq already loaded, we move the
messages at the end of the init routine to avoid confusing output
if the loading of powernow-k8 should not succeed.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
cpufreq modules are often loaded from init scripts that assume that
all recent AMD systems will use powernow-k8.
To inform the user of the change of support and ease the transition
to acpi-cpufreq, emit a warning message.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
To workaround some Windows specific behavior, the ACPI _PSD table
on AMD desktop boards advertises all cores as dependent, meaning
that they all can only use the same P-state. acpi-cpufreq strictly
obeys this description, instantiating one CPU only and symlinking
the others. But the hardware can have distinct frequencies for each
core and powernow-k8 did it that way.
So, in order to use the hardware to its full potential and keep the
original powernow-k8 behavior, lets override the _PSD table setting
on AMD hardware.
We use the siblings table, as it matches the current hardware
behavior.
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
The programming model for P-states on modern AMD CPUs is very similar to
that of Intel and VIA. It makes sense to consolidate this support into one
driver rather than duplicating functionality between two of them. This
patch adds support for AMDs with hardware P-state control to acpi-cpufreq.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Andre Przywara <andre.przywara@amd.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
_PSS objects can also be missing if Cool'N'Quiet is disabled in the
BIOS. Add that to the FW_BUG message for the user to try before updating
her BIOS. Fix formatting while at it.
Acked-by: Mark Langsdorf <mark.langsdorf@amd.com>
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
This change initialises the cpu id field of cs_cpu_dbs_info structure in
conservative governor and keep this consistent with other governors.
Similar initialisation is present in ondemand governor.
Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
* 'imx/fixes-for-3.6' of git://git.linaro.org/people/shawnguo/linux-2.6:
ARM: dts: imx51-babbage: fix esdhc cd/wp properties
ARM: imx6: spin the cpu until hardware takes it down
ARM i.MX6q: Add virtual 1/3.5 dividers in the LDB clock path
Also updates to Linux 3.6-rc2
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Initalizers for deferrable delayed_work are confused.
* __DEFERRED_WORK_INITIALIZER()
* DECLARE_DEFERRED_WORK()
* INIT_DELAYED_WORK_DEFERRABLE()
Rename them to
* __DEFERRABLE_WORK_INITIALIZER()
* DECLARE_DEFERRABLE_WORK()
* INIT_DEFERRABLE_WORK()
This patch doesn't cause any functional changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
On OMAP4, if the first CPU fails to get a valid frequency table (this
could happen if the platform does not register any OPP table), the
subsequent CPU instances end up dealing with a NULL freq_table and
crash.
Check for an already existing freq_table, before trying to create one,
and increment the freq_table_users only if the table is sucessfully
created.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: <linux-pm@vger.kernel.org>
Signed-off-by: Kevin Hilman <khilman@ti.com>
Mark Langsdorf