Doing an 'ifconfig ethN down' followed by an 'ifconfig ethN up' on a qemu-kvm
guest system configured with two e1000 NICs can result in an 'unable to handle
kernel paging request at 0000000100000000' or 'bad page map in process ...' or
something similar.
These result from a 4096-byte page being corrupted with the following two-word
pattern (16-bytes) repeated throughout the entire page:
0x0000000000000000
0x0000000100000000
There can be other bits set as well. What is a constant is that the 2nd word
has the 32nd bit set. So one could see:
:
0x0000000000000000
0x0000000100000000
0x0000000000000000
0x0000000172adc067 <<< bad pte
0x800000006ec60067
0x0000000700000040
0x0000000000000000
0x0000000100000000
:
Which came from from a process' page table I dumped out when the marked line
was seen as bad by print_bad_pte().
The repeating pattern represents the e1000's two-word receive descriptor:
struct e1000_rx_desc {
__le64 buffer_addr; /* Address of the descriptor's data buffer */
__le16 length; /* Length of data DMAed into data buffer */
__le16 csum; /* Packet checksum */
u8 status; /* Descriptor status */
u8 errors; /* Descriptor Errors */
__le16 special;
};
And the 32nd bit of the 2nd word maps to the 'u8 status' member, and
corresponds to E1000_RXD_STAT_DD which indicates the descriptor is done.
The corruption appears to result from the following...
. An 'ifconfig ethN down' gets us into e1000_close(), which through a number
of subfunctions results in:
1. E1000_RCTL_EN being cleared in RCTL register. [e1000_down()]
2. dma_free_coherent() being called. [e1000_free_rx_resources()]
. An 'ifconfig ethN up' gets us into e1000_open(), which through a number of
subfunctions results in:
1. dma_alloc_coherent() being called. [e1000_setup_rx_resources()]
2. E1000_RCTL_EN being set in RCTL register. [e1000_setup_rctl()]
3. E1000_RCTL_EN being cleared in RCTL register. [e1000_configure_rx()]
4. RDLEN, RDBAH and RDBAL registers being set to reflect the dma page
allocated in step 1. [e1000_configure_rx()]
5. E1000_RCTL_EN being set in RCTL register. [e1000_configure_rx()]
During the 'ifconfig ethN up' there is a window opened, starting in step 2
where the receives are enabled up until they are disabled in step 3, in which
the address of the receive descriptor dma page known by the NIC is still the
previous one which was freed during the 'ifconfig ethN down'. If this memory
has been reallocated for some other use and the NIC feels so inclined, it will
write to that former dma page with predictably unpleasant results.
I realize that in the guest, we're dealing with an e1000 NIC that is software
emulated by qemu-kvm. The problem doesn't appear to occur on bare-metal. Andy
suspects that this is because in the emulator link-up is essentially instant
and traffic can start flowing immediately. Whereas on bare-metal, link-up
usually seems to take at least a few milliseconds. And this might be enough
to prevent traffic from flowing into the device inside the window where
E1000_RCTL_EN is set.
So perhaps a modification needs to be made to the qemu-kvm e1000 NIC emulator
to delay the link-up. But in defense of the emulator, it seems like a bad idea
to enable dma operations before the address of the memory to be involved has
been made known.
The following patch no longer enables receives in e1000_setup_rctl() but leaves
them however they were. It only enables receives in e1000_configure_rx(), and
only after the dma address has been made known to the hardware.
There are two places where e1000_setup_rctl() gets called. The one in
e1000_configure() is followed immediately by a call to e1000_configure_rx(), so
there's really no change functionally (except for the removal of the problem
window. The other is in __e1000_shutdown() and is not followed by a call to
e1000_configure_rx(), so there is a change functionally. But consider...
. An 'ifconfig ethN down' (just as described above).
. A 'suspend' of the system, which (I'm assuming) will find its way into
e1000_suspend() which calls __e1000_shutdown() resulting in:
1. E1000_RCTL_EN being set in RCTL register. [e1000_setup_rctl()]
And again we've re-opened the problem window for some unknown amount of time.
Signed-off-by: Andy Gospodarek <andy@greyhouse.net>
Signed-off-by: Dean Nelson <dnelson@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for SJW user settings to not set the synchronization
jump width (SJW) to 1 in any case when using the in-kernel bittiming
calculation.
The ip-tool from iproute2 already supports to pass the user defined SJW
value. The given SJW value is sanitized with the controller specific sjw_max
and the calculated tseg2 value. As the SJW can have values up to 4 providing
this value will lead to the maximum possible SJW automatically. A higher SJW
allows higher controller oscillator tolerances.
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch also changes writel/readl to iowrite32/ioread32.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds the driver for the SJA1000 based PCMCIA card 'CPC-Card' from
EMS Dr. Thomas Wuensche (http://www.ems-wuensche.de).
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Markus Plessing <plessing@ems-wuensche.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
wrqu->encoding.length comes from the network administrator. It's
size u16. We want to limit "tocopy" to the smallest value of either
"len_keys", "wrqu->encoding.length" or 100. But because .length
gets cast from u16 to u8 we might use a random, smaller value than
the was desired. It's probably not very serious, but we may as well
fix it.
Btw, this is from code auditing and not from testing. I don't know
if this affects anyone in real life.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When we cancel a scan, the completion runs
only from the workqueue. This can cause the
remain-on-channel scan to fail when another
one was just canceled, because we're still
aborting it.
To fix this, run the completion inline with
the lock still held before returning from
iwl_scan_cancel_timeout().
Also, to avoid the scan complete work from
completing a new scan prematurely, add a
new STATUS_SCAN_COMPLETE bit.
Reported-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Tested-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
To make the next patch easier to read, move
the function up, it'll be needed earlier in
this file in the next patch.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We'll need to be able to run scan complete
inline, not from the workqueue, so refactor
it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
The return value of iwl_scan_cancel_timeout()
isn't used anywhere, so let's just remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Only 5150 series devices report their temperature
in Kelvin, and for those we already convert it to
Celsius when storing into priv->temperature, so
there's no way priv->temperature will ever be in
Kelvin. Remove support for this.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When an AP mode interface is added with a DTIM
period of two, the slot programming is wrong.
Fix it by taking into account the DTIM period.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If iwl_scan_initiate() fails for any reason,
priv->scan_request and priv->scan_vif are left
dangling. This can lead to a crash later when
iwl_bg_scan_completed() tries to run a pending
scan request.
In practice, this seems to be very rare due to
the STATUS_SCANNING check earlier. That check,
however, is wrong -- it should allow a scan to
be queued when a reset/roc scan is going on.
When a normal scan is already going on, a new
one can't be issued by mac80211, so that code
can be removed completely. I introduced this
bug when adding off-channel support in commit
266af4c745.
Cc: stable@kernel.org [3.0]
Reported-by: Peng Yan <peng.yan@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
As everybody knows kcalloc checks the multiplication is safe and
that we don't run into overflow.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In the current code, the rate scaling isn't fed with
statistics from the BA notifications.
This is since my patch:
iwlagn: reclaim the packets in transport layer
Fix that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Add debugging to show the status of probe in scan notification
to help debug probe related issues
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since all the queue logic has been moved to the transport layer,
the sequence number is set in the transport layer.
While doing that I forgot that the mac header is copied to the
TB of the TX cmd in the upper layer before the call to the transport
layer. So basically we used the sequence number from mac80211...
This was fine for the first assocation but after the second, mac80211
resets its counters while we don't hence a shift that led to terrible
impact on performance.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Since priv->temperature is signed, we cannot use debugfs_create_u32
to refer to it.
Use a regular debugfs file instead.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Txid was used without being initialized.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After 'ath9k: optimize ath9k_ps_restore', it would only send the device to
network sleep and not to full sleep anymore, potentially causing more
battery drain.
Reported-by: Vivek Natarajan <nataraja@qca.qualcomm.com>
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
After handling command response, cmd skb is inserted into command
free queue(which keeps track of availabile skbs) for reuse purpose.
Skb length is not getting reset to zero here. This patch takes care
of it.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Yogesh Ashok Powar <yogeshp@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
ieee80211_channel_to_frequency() routine expects band parameter in
the form of "enum ieee80211_band band". Currently driver specific
band (BAND_A, BAND_AN etc.) is passed to the routine.
This patch makes sure that correct parameter is passed.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
In recent commit "mwifiex: use cfg80211 dynamic scan..."
(7c6fa2a843..) scan table handling in driver is removed to
make use of cfg80211 dynamic scan table. Now driver sends
beacon buffers found in scanning directly to stack and parse
the buffer for requested BSS only during association.
Beacon buffer doesn't contain bss band information. Driver
gets it from firmware in separate tlv (chan_band_tlv).
Currently since we don't inform stack about bss bandinfo,
there is an issue with 5GHz association.
Use "priv" field of struct cfg80211_bss to store bandinfo.
This fixes 5GHz association issue.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Sometimes association in 5GHz doesn't work. Dmesg log shows
"Can not find requested SSID xyz" error message. Currently
while preparing scan channel list for firmware Null entries
are created for disabled channels. The routine which retrieves
this list ignores channels after Null entry. Hence sometimes
driver doesn't scan the channel of requested AP and association
fails. The issue is fixed by avoiding those NULL entries.
Signed-off-by: Amitkumar Karwar <akarwar@marvell.com>
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
When scanning for the broadcast SSID, there is no need to add the
SSID TLV (restoring the behaviour of the driver behaviour in the wext
days, confirmed in Marvell specifications).
If bssid is unspecified, the current scan code will usually fire off an
active scan probing for the specific requested SSID. However, if a scan
is ongoing (or has just finished), those scan results will be used
instead (even if that scan is totally different, e.g. a passive scan on
channel 4 for a different SSID). Fix this inconsistency by always
firing off a scan when associating without a bssid.
Signed-off-by: Daniel Drake <dsd@laptop.org>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
TSF can be kept per vif.
Add ieee80211_vif param to set/get/reset_tsf, and move
the debugfs entries to the per-vif directory.
Update all the drivers that implement these callbacks.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
this represents the bitmap of block ACK received after the
successful transmission of an aggregate frame. also made few
changes to beautify the display
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Most boards with SysKonnect/Marvell Ethernet have only a single port.
For the single port case, use the standard Ethernet driver convention
of allocating IRQ when device is brought up rather than at probe time.
This patch also adds some additional read after writes to avoid any
PCI posting problems when setting the IRQ mask.
The error handling of dual port cards is also changed. If second port
can not be brought up, then just fail. No point in continuing, since
the failure is most certainly because of out of memory.
It is worth noting that the dual port skge device has a single irq but two
seperate status rings and therefore has two NAPI objects, one for
each port.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This fix provides a newly flashed FW version (appended, in braces)
along with the currently running FW version via ethtool. The newly
flashed version runs only after a system reset.
Signed-off-by: Suresh Reddy <Suresh.Reddy@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Re-posting with subject fixed!
Multicast programming has been broken since commit 5b8821b7. Setting the
MULTICAST flag while sending the cmd to the FW was missing. Fixed this.
Also fixed-up some indentation in the adjacent lines.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch touchs most of the enic port profile handling code.
Tried to break it into sub patches without success.
The patch mainly does the following:
- Port profile operations for a SRIOV VF are modified to work
only via its PF
- Changes the port profile static struct in struct enic to a pointer.
This is because a SRIOV PF has to now hold the port profile information
for all its VF's
- Moved address registration for VF's during port profile ASSOCIATE time
- Most changes in port profile handling code are changes related to indexing
into the port profile struct array of a PF for the VF port profile
information
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds helper functions to use PF as proxy for SRIOV VF firmware
commands.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch adds support to enable SRIOV on enic devices. Enic SRIOV VF's are dynamic vnics and will use the same driver code as dynamic vnics.
Signed-off-by: Roopa Prabhu <roprabhu@cisco.com>
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Christian Benvenuti <benve@cisco.com>
Signed-off-by: David Wang <dwang2@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Most sky2 hardware only has a single port, although some variations of the
chip support two interfaces. For the single port case, use the standard
Ethernet driver convention of allocating IRQ when device is brought up
rather than at probe time.
Also, change the error handling of dual port cards so that if second
port can not be brought up, then just fail. No point in continuing, since
the failure is most certainly because of out of memory.
The dual port sky2 device has a single irq and a single status ring,
therefore it has a single NAPI object shared by both ports.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
netdev is unused in pch_gbe_setup_rctl. Remove this declaration to
avoid a compiler warning.
Signed-off-by: Jon Mason <jdmason@kudzu.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
Currently ehea ndo_get_stats can sleep in two places, in a hcall
and in a GFP_KERNEL alloc, which is not correct.
This patch creates a delayed workqueue that grabs the information each 1
sec from the hardware, and place it into the device structure, so that,
.ndo_get_stats quickly returns the device structure statistics block.
Signed-off-by: Breno Leitao <brenohl@br.ibm.com>
Acked-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This commit adds one step support to the phyter. When enabled, the
hardware does not provide time stamps for transmitted sync messages but
instead inserts the stamp into the outgoing packet.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
This patch enables six external event channels and one periodic output.
One GPIO is reserved for synchronizing multiple PHYs. The assignment
of GPIO functions can be changed via a module parameter.
The code supports multiple simultaneous events by inducing a PTP clock
event for every channel marked in the PHY's extended status word.
Signed-off-by: Richard Cochran <richard.cochran@omicron.at>
Signed-off-by: David S. Miller <davem@davemloft.net>
proper dma_unmapping and freeing of skb's has to be done in the rx
cleanup for EDMA chipsets when the device is unloaded and this also
seems to address the following warning which shows up occasionally when
the device is unloaded
Call Trace:
[<c0148cd2>] warn_slowpath_common+0x72/0xa0
[<c03b669c>] ? dma_debug_device_change+0x19c/0x200
[<c03b669c>] ? dma_debug_device_change+0x19c/0x200
[<c0148da3>] warn_slowpath_fmt+0x33/0x40
[<c03b669c>] dma_debug_device_change+0x19c/0x200
[<c0657f12>] notifier_call_chain+0x82/0xb0
[<c0171370>] __blocking_notifier_call_chain+0x60/0x90
[<c01713bf>] blocking_notifier_call_chain+0x1f/0x30
[<c044f594>] __device_release_driver+0xa4/0xc0
[<c044f647>] driver_detach+0x97/0xa0
[<c044e65c>] bus_remove_driver+0x6c/0xe0
[<c029af0b>] ? sysfs_addrm_finish+0x4b/0x60
[<c0450109>] driver_unregister+0x49/0x80
[<c0299f54>] ? sysfs_remove_file+0x14/0x20
[<c03c3ab2>] pci_unregister_driver+0x32/0x80
[<f92c2162>] ath_pci_exit+0x12/0x20 [ath9k]
[<f92c8467>] ath9k_exit+0x17/0x36 [ath9k]
[<c06523cd>] ? mutex_unlock+0xd/0x10
[<c018e27f>] sys_delete_module+0x13f/0x200
[<c02139bb>] ? sys_munmap+0x4b/0x60
[<c06547c5>] ? restore_all+0xf/0xf
[<c0657a20>] ? spurious_fault+0xe0/0xe0
[<c01832f4>] ? trace_hardirqs_on_caller+0xf4/0x180
[<c065b863>] sysenter_do_call+0x12/0x38
---[ end trace 16e1c1521c06bcf9 ]---
Mapped at:
[<c03b7938>] debug_dma_map_page+0x48/0x120
[<f92ba3e8>] ath_rx_init+0x3f8/0x4b0 [ath9k]
[<f92b5ae4>] ath9k_init_device+0x4c4/0x7b0 [ath9k]
[<f92c2813>] ath_pci_probe+0x263/0x330 [ath9k]
Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Driver rtl8192cu assigns a new struct rtl_tcb_desc object, but fails to
clear it.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Stable <stable@kernel.org> [2.6.39+]
Signed-off-by: John W. Linville <linville@tuxdriver.com>
If iwl_scan_initiate() fails for any reason,
priv->scan_request and priv->scan_vif are left
dangling. This can lead to a crash later when
iwl_bg_scan_completed() tries to run a pending
scan request.
In practice, this seems to be very rare due to
the STATUS_SCANNING check earlier. That check,
however, is wrong -- it should allow a scan to
be queued when a reset/roc scan is going on.
When a normal scan is already going on, a new
one can't be issued by mac80211, so that code
can be removed completely. I introduced this
bug when adding off-channel support in commit
266af4c745.
Cc: stable@kernel.org [3.0]
Reported-by: Peng Yan <peng.yan@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Argument list to CDRP function has become unmanageably long. Fix it by properly
declaring a struct that encompasses all the input and output parameters.
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ameen Rahman <ameen.rahman@qlogic.com>
Signed-off-by: Anirban Chakraborty <anirban.chakraborty@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The imx6q enet is a derivative of imx28 enet controller. It fixed
the frame endian issue found on imx28, and added 1 Gbps support.
It also fixes a typo on vendor name in Kconfig.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
In function fec_enet_mii_init(), it uses non-zero pdev->id as part
of the condition to check the second fec instance (fec1). This works
before the driver supports device tree probe. But in case of device
tree probe, pdev->id is -1 which is also non-zero, so the logic becomes
broken when device tree probe gets supported.
The patch change the logic to check "pdev->id > 0" as the part of the
condition for identifying fec1.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
FEC can work without a phy reset on some platforms, which means not
very platform necessarily have a phy-reset gpio encoded in device tree.
Even on the platforms that have the gpio, FEC can work without
resetting phy for some cases, e.g. boot loader has done that.
So it makes more sense to have the phy-reset-gpio request failure as
a debug message rather than a warning, and get fec_reset_phy() return
void since the caller does not check the return anyway.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Finish conversion to unified ethtool ops: convert get_flags.
Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
The SEEQ drivers should depend on HAS_IOMEM to prevent compile breakage
on !HAS_IOMEM architectures:
drivers/net/ethernet/seeq/seeq8005.c: In function 'seeq8005_probe1':
drivers/net/ethernet/seeq/seeq8005.c:179:2: error:
implicit declaration of function 'inw' [-Werror=implicit-function-declaration]
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Reloading FW during resets can cause issues. Remove the full reset
as it is not needed.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Add support for WOL as determined by the EEPROM.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This change is meant to avoid a hardware lockup when Tx work is still
pending and we request a reset.
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
This patch adds support for configuring the priority to
traffic class mapping.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
We don't need SFP+ plugable support for X540 hardware (copper only) so
don't enable the SFP+ interrupts.
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
The DCB CEE command set_state() will complete successfully
but is misleading because it enables IEEE mode. After
this patch the command is failed.
And IEEE PFC/ETS is managed from ieee paths now instead
of using CEE primitives.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the PCI device flag indicating if a VF is assigned to a guest VM
to guard against destroying VFs upon driver removal. Implement
additional feature to detect if VFs already exist when the driver
is loaded and if so configure them and set the driver state to
SR-IOV enabled.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Use the AP_MAX_LINKS as the upper boundary for traversing the links array,
thereby guaranteeing BA sessions with all connected STAs are stopped when
the stop_ba event is received.
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Fix an erroneous labeling of array boundaries in the fw_status structure.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Save the configured bitrate, and use the min allowed rate
as the basic rate (e.g. when scanning).
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
If a hidden SSID is requested, generate a probe response template
containing the real SSID.
Depends on the patch "mac80211: add ssid config to bss information
in AP-mode".
Signed-off-by: Arik Nemtsov <arik@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
On roaming, the auth and assoc req are sent with the sta
hlid. This is wrong, as the sta hlid is configured according
to the old ap. Use the dev_hlid instead.
Move the wl1271_tx_update_filters() call into wl1271_tx_get_hlid(),
so wl->dev_hlid will be valid.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
There is a race condition between wl1271_tx_work() and the
channel switch, so make sure all the pending packets are
being sent before switching channel.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl12xx uses a single probe response template, regardless of
the probe request.
However, the P2P spec forbids including the p2p ie in some
cases (e.g. the probe request didn't include the p2p ie).
The fw responds only to probe requests that don't
include the p2p ie, and passes up probe requests that
include them (the supplicant will answer them).
Thus, strip the p2p ie from the probe response template.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
wl12xx uses the beacon as the probe response template.
However, the beacon includes a TIM ie, which shouldn't
exist in the probe response.
Delete it from the skb before configuring the probe
response template.
Signed-off-by: Eliad Peller <eliad@wizery.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
We were including only 11b rates in IBSS mode. This patch adds OFDM
rates.
[Rephrased commit log and removed one unnecessary comment. -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Due to some changes in PM in recent kernels, the sdio_test module has
been broken for a while. This patch fixes the code that powers the
card on and off.
Also made some small indentation fixes in the Makefile.
[Rephrased commit log and removed the change in the FW name, since
it's done in another patch. -- Luca]
Signed-off-by: Shahar Levi <shahar_levi@ti.com>
Signed-off-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Shreyas Bhatewara <sbhatewara@vmware.com>
Cc: "VMware, Inc." <pv-drivers@vmware.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: virtualization@lists.linux-foundation.org
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Francois Romieu <romieu@fr.zoreil.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: David Dillow <dave@thedillows.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Alexander Indenbaum <baum@tehutinetworks.net>
Cc: Andy Gospodarek <andy@greyhouse.net>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Stephen Hemminger <shemminger@linux-foundation.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Solarflare linux maintainers <linux-net-drivers@solarflare.com>
Cc: Steve Hodgson <shodgson@solarflare.com>
Cc: Ben Hutchings <bhutchings@solarflare.com>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Ian Campbell <ian.campbell@citrix.com>
Cc: Jon Mason <jdmason@kudzu.us>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
We were using incorrect max and min dwell times during forced passive
scans because we were still using the active scan states to scan
(passively) the channels that were not marked as passive.
Instead of doing passive scans in active states, we now skip active
states and scan for all channels in passive states.
Cc: <stable@kernel.org> # 2.6.36+
Signed-off-by: Luciano Coelho <coelho@ti.com>
- fix features : jumbo frames and checksumming can not be used at the
same time.
- introduce hw_jumbo_{enable / disable} helpers. Their content has been
creatively extracted from Realtek's own drivers. As an illustration,
it would be nice to know how/if the MaxTxPacketSize register operates
when the device can work with a 9k jumbo frame as its documentation
(8168c) can not be applied beyond ~7k.
- rtl_tx_performance_tweak is moved forward. No change.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
8168d and above allow jumbo frames beyond 8k. Bump the received
packet length check before enabling jumbo frames on these chipsets.
Frame length indication covers bits 0..13 of the first Rx descriptor
32 bits for the 8169 and 8168. I only have authoritative documentation
for the allowed use of the extra (13) bit with the 8169 and 8168c.
Realtek's drivers use the same mask for the 816x and the fast ethernet
only 810x.
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com>
For RTL8111EVL, the register of MaxTxPacketSize doesn't acctually
limit the tx size. It influnces the feature of early tx.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
If register_netdev() fails now, then we call mutex_unlock(&bnad->conf_mutex);
on the error path, but it's already unlocked. So we acquire the lock in error
path which will be later unlocked after the cleanup.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Rasesh Mody <rmody@brocade.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
We dereference "rate" on the lines before so the checks here are too
late to help. This function is only called from
mwifiex_dump_station_info() and "rate" is always a non-NULL pointer
so the check can be removed.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
We're not likely to hit this small memory leak, but lets fix it
anyway to keep the static checkers happy.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
iwl_trans_rx_alloc is only called from iwl_rx_init, so no need
to init the lists twice.
Signed-off-by: Amit Beka <amit.beka@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
During my works on the transport layer I removed code that updated
a local variable (is_agg) that is needed to keep the pending_frames
count up to date. Fix this.
Also, there should be no way to have a packet with TX_CTL_AMPDU set
while the internal aggregation state machine is not in AGG_ON state.
Add a WARN_ON to ensure that.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This has been removed but the declaration hasn't.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
This simplifies both the transport layer and the upper layer.
Kill the union in the device command, which avoids the funny syntax
we had: cmd->cmd.payload.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
Dean Nelson