Use generic DMA DT helper.
Platforms booting with or without DT populated are both supported.
Based on Ludovic Desroches <ludovic.desroches@atmel.com> patchset
"ARM: at91: move to generic DMA device tree binding"
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
Acked-by: Ludovic Desroches <ludovic.desroches@gmail.com>
Signed-off-by: Mark Brown <broonie@linaro.org>
Fill in the recently added spi_master.bits_per_word_mask field in as
many drivers as possible. Make related cleanups, such as removing any
redundant error-checking, or empty setup callbacks.
Signed-off-by: Stephen Warren <swarren@wwwdotorg.org>
Acked-by: H Hartley Sweeten <hsweeten@visionengravers.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Fix using PIO transfer mode only support 8 bits transfer, doesn't support 16 bits.
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
[wenyou.yang@atmel.com: submit the patch]
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Add dmaengine support.
Using "has_dma_support" member of struct is used to select
the transfer mode: dmaengine or pdc.
For the dmaengine transfer mode, it supports both 8 bits and 16 bits transfer.
For the dmaengine transfer mode, if it fails to config dmaengine,
or if the message length is less than 16 bytes, it will use the PIO transfer mode.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[wenyou.yang@atmel.com: using "has_dma_support" to select dmaengine as the spi xfer mode]
[wenyou.yang@atmel.com: fix DMA: OOPS if buffer > 4096 bytes]
[wenyou.yang@atmel.com: submit the patch]
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Richard Genoud <richard.genoud@gmail.com>
[richard.genoud@gmail.com: update with dmaengine interface]
[richard.genoud@gmail.com: fix __init/__devinit sections mismatch]
[richard.genoud@gmail.com: adapt to slave_config changes]
[richard.genoud@gmail.com: add support t0 16 bits transfer]
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Will allow to drop the lock during DMA operations.
Replacing non-irqsave versions with irqsave versions of the lock
to make it correct in both pdc and dmaengine transfer mode
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[wenyou.yang@atmel.com: submit the patch]
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Needed for future use with dmaengine enabled driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
[wenyou.yang@atmel.com: submit the patch]
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Tested-by: Richard Genoud <richard.genoud@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
atmel_spi_transfer() would check speed_hz and fail if
the speed was changed in the transfer. After commit
"spi: make sure all transfer has proper speed set"
this would happen on all transfers.
Change speed_hz check to only fail if a lower speed
than max is requested.
Signed-off-by: Joachim Eastwood <manabian@gmail.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
The status of transfer is stored in controller data structure
so that it can be used not only by atmel_spi_msg_done() function.
This will be useful for upcoming dmaengine enabled driver.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
The "has_dma_support" needed for future use with dmaengine driver.
[Fixed some unneded ternery operators -- broonie]
Signed-off-by: Wenyou Yang <wenyou.yang@atmel.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Some of the spi driver module remove hooks were annotated with __exit
and referenced with __exit_p(). Presumably these were supposed to be
__devinit, __devexit and __devexit_p() since __init/__exit for a
probe/remove hook has never been correct. They also got missed during
the big __devinit/__devexit purge since they didn't match the pattern.
Remove then now to be rid of it.
v2: purge __init also
Reported-by: Arnd Bergmann <arnd@arndb.de>
[Arnd set a patch cleaning up one, and then I found more]
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Use the newly introduce cs-gpios dt support on atmel.
We do not use the hardware cs as it's wired and has bugs and limitations.
As the controller believes that only active-low devices/systems exists.
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Primarily SPI device driver bug fixes, one removal of an old driver, and
some new tegra support. There is some core code change too, but all in
all pretty small stuff. The new features to note are:
- Common code for describing GPIO CS lines in the device tree
- Remove the SPI_BUFSIZ limitation on spi_write_the_read()
- core spi ensures bits_per_word is set correctly
- SPARC can now use SPI
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.4.11 (GNU/Linux)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=bvpH
-----END PGP SIGNATURE-----
Merge tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6
Pull SPI updates from Grant Likely:
"Primarily SPI device driver bug fixes, one removal of an old driver,
and some new tegra support. There is some core code change too, but
all in all pretty small stuff.
The new features to note are:
- Common code for describing GPIO CS lines in the device tree
- Remove the SPI_BUFSIZ limitation on spi_write_the_read()
- core spi ensures bits_per_word is set correctly
- SPARC can now use SPI"
* tag 'spi-for-linus' of git://git.secretlab.ca/git/linux-2.6: (36 commits)
spi/sparc: Allow of_register_spi_devices for sparc
spi: Remove HOTPLUG section attributes
spi: Add support for specifying 3-wire mode via device tree
spi: Fix comparison of different integer types
spi/orion: Add SPI_CHPA and SPI_CPOL support to kirkwood driver.
spi/sh: Add SH Mobile series as dependency to MSIOF controller
spi/sh-msiof: Remove unneeded clock name
spi: Remove SPI_BUFSIZ restriction on spi_write_then_read()
spi/stmp: remove obsolete driver
spi/clps711x: New SPI master driver
spi: omap2-mcspi: remove duplicate inclusion of linux/err.h
spi: omap2-mcspi: Fix the redifine warning
spi/sh-hspi: add CS manual control support
of_spi: add generic binding support to specify cs gpio
spi: omap2-mcspi: remove duplicated include from spi-omap2-mcspi.c
spi/bitbang: (cosmetic) simplify list manipulation
spi/bitbang: avoid needless loop flow manipulations
spi/omap: fix D0/D1 direction confusion
spi: tegra: add spi driver for sflash controller
spi: Dont call master->setup if not populated
...
CONFIG_HOTPLUG is going away as an option. As result the __dev*
markings will be going away.
Remove use of __devinit, __devexit_p, __devinitdata, __devinitconst,
and __devexit.
Bill Pemberton has done most of the legwork on this series. I've used
his script to purge the attributes from the drivers/gpio tree.
Reported-by: Bill Pemberton <wfp5p@virginia.edu>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Commit 940ab889 "drivercore: Add helper macro for platform_driver boilerplate"
converted this driver to use module_platform_driver, but due to the use
of platform_driver_probe(), this resulted in the call to atmel_spi_probe being
lost. Place the call to this function into the driver structure.
fix section missmatch
atmel_spi_probe is marked __init where it's supposed to be __devinit
atmel_spi_remove is marked __exit where it's supposed to be __devexit
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Russell King - ARM Linux <linux@arm.linux.org.uk>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
* 'spi/next' of git://git.secretlab.ca/git/linux-2.6:
drivercore: Add helper macro for platform_driver boilerplate
spi: irq: Remove IRQF_DISABLED
OMAP: SPI: Fix the trying to free nonexistent resource error
spi/spi-ep93xx: add module.h include
spi/tegra: fix compilation error in spi-tegra.c
spi: spi-dw: fix all sparse warnings
spi/spi-pl022: Call pl022_dma_remove(pl022) only if enable_dma is true
spi/spi-pl022: calculate_effective_freq() must set rate <= requested rate
spi/spi-pl022: Don't allocate more sg than required.
spi/spi-pl022: Use GFP_ATOMIC for allocation from tasklet
spi/spi-pl022: Resolve formatting issues
For simple modules that contain a single platform_driver without any
additional setup code then ends up being a block of duplicated
boilerplate. This patch adds a new macro, module_platform_driver(),
which replaces the module_init()/module_exit() registrations with
template functions.
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Greg Kroah-Hartman <gregkh@suse.de>
Reviewed-by: Magnus Damm <magnus.damm@gmail.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Sort the SPI makefile and enforce the naming convention spi_*.c for
spi drivers.
This change also rolls the contents of atmel_spi.h into the .c file
since there is only one user of that particular include file.
v2: - Use 'spi-' prefix instead of 'spi_' to match what seems to be
be the predominant pattern for subsystem prefixes.
- Clean up filenames in Kconfig and header comment blocks
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Mark Brown