On some Samsung SoCs not all SDHCI controllers have card detect (CD)
line. For some embedded designs it is not even needed, because ususally
the device (like SDIO flash memory or wifi controller) is permanently
wired to the controller. There are also systems which have a card detect
line connected to some of the external interrupt lines or the presence
of the card depends on some other actions (like enabling a power
regulator).
This patch adds all required changes to platform support code, so
another patch, which extends the driver with support for the new card
detection methods can be applied.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title and coding-style fixes]
[kgene.kim@samsung.com: fix build errors]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds hsmmc3 device definition in plat-samsung. Because now
S5PV210 can support 4 hsmmc such as hsmmc0, hsmmc1, hsmmc2 and hsmmc3
and that can be used in further Samsung SoCs.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch implements s3c_adc_setname() for Samsung SoCs.
Also updates its usage in S3C64XX, S5P6440, and S5PV210.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Following is added for the CF-ATA driver:
- Platform data strucure instantiation
- Platform device enabling code
- Addition of cfcon clock
- Platform-specific gpio setup code
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Following has been added:
- Common CF Platform device definition
- Platform data strucure definition
- CF controller register definitions
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This is intended to replace a number of sites in the Samsung kernel
where the same thing is being repeated in specific platform setting
code. See next patches for replacements.
Signed-off-by: Ben Dooks <ben-linux@fluff.org>
[kgene.kim@samsung.com: This is for building test]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch reduces the virtual memory allocated for WDT device from 1M
to 1K.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Ben Dooks <ben-linux@fluff.org>
This patch adds configuration of proper mux pins for support
I2C channel 0, 1, and 2 on S5PV310/S5PC210.
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: coding-style and minor comment fixes]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the Kconfig and Makefile for the new S5PV310 SoC.
It also updates arch/arm Kconfig, Makefile and arch/arm/mm/Kconfig
to include support for the new S5PV310.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds timer support for S5PV310. Until now, all S5P SoCs
use CONFIG_ARCH_USES_GETTIMEOFFSET macro as a default configuration.
Instead,S5PV310 implements clocksource and clock_event_device to
support the high resolution timer and tickless system.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds IRQ support for S5PV310.
ARM GIC is installed in S5PV310 instead of VIC which is in every other CPUs
in S5P series. Several irq combiners are used to resolve the lack of irq
lines in current implementation.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds clock and pll support for S5PV310.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds Samsung S5PV310/S5PC210 CPU support.
The S5PV310/S5PC210 integrates a ARM Cortex A9 multi-core.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Jiseong Oh <jiseong.oh@samsung.com>
[kgene.kim@samsung.com: fix build errors]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The uart offset between channels has been 0x400 for all S5P series
and to present virtual and physical offsets, both number 0x400 and
S3C_UART_OFFSET have been used together.
This patch removes the use of the number 0x400 and expands the virtual
mapping size of S3C_VA_UART from 4KB to 512KB to support the CPU with
S3C_UART_OFFSET being 0x10000.
Signed-off-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Add support for the FRACVAL register on the newer UART blocks which provides
the same function as UDIVSLOT register but the FRACVAL is easier to implement.
To support UDIVSLOT register, UDIVSLOT table search is necessary though
supporting FRACVAL only needs the index value of UDIVSLOT table.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Acked-by: Changhwan Youn <chaos.youn@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds s5pv210_sw_reset() which includes SWRESET for S5PV210/S5PC110.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support RTC driver for Samsung S5PV210/S5PC110.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support HSMMC on SMDKV210, and gpio configuration for
S5PV210 hsmmc3.
Signed-off-by: Hyuk Lee <hyuk1.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch is to support keypad device to the SMDKV210 board.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds the keypad device platform helpers for S5PV210 cpu.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Now that S5PC110 machines and S5PV210 machines can be built into
one kernel, update mach-s5pv210/Kconfig and s5pv210_defconfig.
Tested on Aquila(S5PC110), GONI(S5PC110), SMDKC110(S5PC110)
and SMDKV210(S5PV210).
Created and tested against linux-2.6.35-rc5.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Following is added for the CF-ATA driver:
- Platform data strucure instantiation
- Platform device enabling code
- Platform-specific gpio setup code
- Fixed IRQ naming to match across 64xx and v210
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds required platform definitions for MAX8998 PMIC driver. Power
regulators for LDO and BUCK outputs has been defined as well as a simple
gpio-keys button for power key (to enable wakeup functionality with
external interrupt).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[broonie@opensource.wolfsonmicro.com: For the regulator API usage]
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[kgene.kim@samsung.com: minor title fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds required platform definitions for MAX8998 PMIC driver. Power
regulators for LDO and BUCK outputs has been defined as well as a simple
gpio-keys button for power key (to enable wakeup functionality with
external interrupt).
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[broonie@opensource.wolfsonmicro.com: For the regulator API usage]
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
[kgene.kim@samsung.com: minor title fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds required platform definitions to enable s3c-fb
driver on GONI board. One framebuffer window in 480x800x16bpp mode is
defined.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch fixes on MAX_PHYSMEM_BITS for Sparsemem on S5PV210/S5PC110.
Because physical memory can be located from 0x20000000 to 0x7fffffff,
so MAX_PHYSMEM_BITS is 31 and not 32.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch is to support OneNAND device to the Aquila board.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch is to support OneNAND device to the GONI board.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The GONI board uses max UART FIFO size to each UART channels.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
The Aquila board uses max UART FIFO size to each UART channels. UART0
supports 256 bytes FIFO, but Aquila board supports 128 bytes FIFO
because of initial chip bug.
Also, this patch fixes to "s/smdkv210/aquila".
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for MP04 and MP05 gpio banks.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
[kgene.kim@samsung.com: minor title fix]
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch performs minor clocks cleanup for S5PC100 SoC. HSMMC special
clocks has been renamed back to sclk_mmc to match the common style of
clock names. This clock has been also added to sdhci clock source list.
The duplicate HCLK clock entry for sdhci-s3c has been disabled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support RTC driver for Samsung S5PC100.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch is to support keypad device to the SMDKC100 board.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch renames the keypad clock for S5PC100 from keyif to keypad.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for Watchdog timer for Samsung S5PC100.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds touchscreen support for S5PC100.
Signed-off-by: Naveen Krishna Ch <ch.naveen@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
Following is added for the CF-ATA driver:
- Platform data strucure instantiation
- Platform device enabling code
- Platform-specific gpio setup code
Signed-off-by: Abhilash Kesavan <a.kesavan@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support for Watchdog timer for Samsung S5P6442.
Signed-off-by: Banajit Goswami <banajit.g@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds definition of Watchdog Timer map.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support RTC driver for Samsung S5P6440.
Signed-off-by: Atul Dahiya <atul.dahiya@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds s5p_reset_hook() which includes software reset
by using SWRESET.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds support common arch_reset() for
S5P6440, S5P6442, S5PC100 and S5PV210/S5PC110.
Now perform reset using Watchdog reset, SWRESET
support with s5p_reset_hook() will be added later.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds system define for arch_reset() using Watchdog reset.
And adds IO mapping for using WDT.
Signed-off-by: Jongpill Lee <boyko.lee@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch changes the definition name of default UCON, ULCON, and
UFCON UART registers from ARCH(SoC) to Machine(Board). Because it
depends on machine.
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
This patch adds an initcall for the s5p platforms so that they register
their PMU IRQs with the PMU framework in the Kernel.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Signed-off-by: Kukjin Kim <kgene.kim@samsung.com>
ffuart is available on cm-x300 only with pxa300.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Cc: stable <stable@kernel.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Improve formating so checkpatch passes. Also, change some function and variable
names to make the naming consistent.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This huge patch mostly shuffles code. The spitz.c file contained terrible mess
and needed a cleanup, here it is:
1) Made every part modular, components are not built in if not selected.
2) Removed loads of preprocessor goo, mostly "#ifdef MACH_AKITA .... #endif" and
similar code. The kernel size will grow by a few kb now, but the file is much
more readable.
3) Reworked SD/CF power setting function and made it reentrant.
4) Add ISL6271A regulator support
5) Correctly register WM8750
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
This contains common code for Palm LD, TX, T5, Z72, Treo680, Centro
This code also adds PMIC support for all the devices,
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
READ_GPIO_BIT() is no way generic by accessing GPIO registers directly,
replace it with gpio_get_value().
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
IDE_PXA_CF doesn't exist in Kconfig, therefore removing all references
for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Acked-by: Juergen Schindele <schindele@nentec.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
XSCALE_CACHE_ERRATA doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Cc: Nicolas Pitre <nico@fluxnic.net>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
CORGI_SSP_DEPRECATED doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Acked-by: Kristoffer Ericson <kristoffer.ericson@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
ARCH_GUMSTIX_ORIG doesn't exist in Kconfig, therefore removing all
references for it from the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Acked-by: Jaya Kumar <jayakumar.lkml@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
BACKLIGHT_CORGI was later renamed to BACKLIGHT_GENERIC and has not been
used since then. As it's now safe to completely transition to LCD_CORGI
driver, which incorprates both the LCD and backlight device.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
SHARP_LOCOMO doesn't exist in Kconfig, therefore replacing all
references for it with SHARP_LOCOMO in the source code.
Signed-off-by: Christoph Egger <siccegge@cs.fau.de>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This patch:
1) Simpifies the DRI recomputation routine by pulling out the common code
2) Fixes a bug in PXA27x DRI recomputation caused by incorrect parenthesis
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
The latest PXA3xx DM has enabled 312MHz for the HSS bus,
which allows x24 multiplier.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Add bit definitions of the CPR register of the SCOOP chip into scoop.h. Also,
cleanup the GPCR definitions to match coding style.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
With kexec-based kernel boot loader on Zaurus, the machine ID is
actually correctly passed, and head-sharpsl.S is not necessary.
Introduce PXA_SHARPSL_DETECT_MACH_ID, and include head-sharpsl.S
only when that's explicitly enabled.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
1. TOSA related un-hidden options moved to right under MACH_TOSA
2. SHARPSL_PM related hidden options moved to the end of Kconfig
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
With a correct dev->dma_mask before calling dmabounce_register_dev(),
dma_needs_bounce() is not necessary.
The sa1111, though, is a bit complicated. Until it's fully understood
and fixed, dma_needs_bounce() for sa1111 is kept if CONFIG_SA1111 is
enabled with no side effect (with the condition of machine_is_*)
Thanks for Mike Rapoport to fix one error in the original version of
the patch and get this tested.
Acked-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Not tested and enabled on MMP at this moment, and since the IRQ
is different from mach-pxa, I'd prefer to move the PMU device
back into mach-pxa/. Will introduce the PMU device to MMP once
it's enabled and tested.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
pxa3xx cpu needs the irq type setup to be able to
wakeup from low power mode on IRQ_WAKEUPx events.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Signed-off-by: Jonathan Cameron <jic23@cam.ac.uk>
Acked-by: Stefan Schmidt <stefan@datenfreihafen.org>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
This file is scheduled for removal, therefore fix all devices that use this
file to use the suggested wm97xx.h and pass platform data properly.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Tomas Cech <sleep_walker@suse.cz>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (57 commits)
Input: adp5588-keypad - fix NULL dereference in adp5588_gpio_add()
Input: cy8ctmg110 - capacitive touchscreen support
Input: keyboard - also match braille-only keyboards
Input: adp5588-keys - export unused GPIO pins
Input: xpad - add product ID for Hori Fighting Stick EX2
Input: adxl34x - fix leak and use after free
Input: samsung-keypad - Add samsung keypad driver
Input: i8042 - reset keyboard controller wehen resuming from S2R
Input: synaptics - set min/max for finger width
Input: synaptics - only report width on hardware that supports it
Input: evdev - signal that device is writable in evdev_poll()
Input: mousedev - signal that device is writable in mousedev_poll()
Input: change input handlers to use bool when possible
Input: document the MT event slot protocol
Input: introduce MT event slots
Input: usbtouchscreen - implement reset_resume
Input: usbtouchscreen - implement runtime power management
Input: usbtouchscreen - implement basic suspend/resume
Input: Add ATMEL QT602240 touchscreen driver
Input: fix signedness warning in input_set_keycode()
...
Remove kernel.h and module.h since they are not used correctly anyway.
Also, remove device.h since it comes along with platform_device.h
(always will I guess).
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
omap{1,2}-mailbox are modules that provide the 'omap-mailbox' driver.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
No need to dynamically register mailboxes one by one.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Will be useful to identify them later.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
CONFIG_OMAP_DSP is not in mainline, CONFIG_OMAP_MBOX_FWK is.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
OMAP4 ones messed up the organization.
Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
With this patch, you'll get the following sysfs directories. This
structure implies that a single platform device, "omap2-mailbox" holds
multiple logical mbox instances. This could be the base to add sysfs
files for each logical mboxes. Then userland application can access a
mbox through sysfs entries if necessary(ex: setting kfifo size
dynamically)
~# tree -d -L 2 /sys/devices/platform/omap2-mailbox/
/sys/devices/platform/omap2-mailbox/
|-- driver -> ../../../bus/platform/drivers/omap2-mailbox
|-- mbox
| |-- dsp <- they are each instances of logical mailbox.
| |-- ducati
| |-- iva2
| |-- mbox01
| |-- mbox02
| |-- mbox03
| |-- .....
| `-- tesla
|-- power
`-- subsystem -> ../../../bus/platform
This was wrongly dropped by:
commit c7c158e57b
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
The underlying buffering implementation of mailbox
is converted from block API to kfifo due to the simplicity
and speed of kfifo.
The default size of the kfifo buffer is set to 256 bytes.
This value is configurable at compile time (via
CONFIG_OMAP_MBOX_KFIFO_SIZE), and can be changed at
runtime (via the mbox_kfifo_size module parameter).
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Hari Kanigeri <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
rwlocks are slower and have potential starvation issues
therefore spinlocks are generally preferred.
see also: http://lwn.net/Articles/364583/
Signed-off-by: Ohad Ben-Cohen <ohad@wizery.com>
Signed-off-by: Kanigeri Hari <h-kanigeri2@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
when blk_get_request fails to get the request it is returning
without read the message from the mailbox fifo, then when it
leaves the isr and interruption is trigger again and again and
the workqueue which get elements from the request queue is never
executed and the kernel is stuck and shows a softlockup message.
Now the mailbox interrupt is disabled when request queue is full
and enabled when it pop a elememt form the request queue.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
mailbox startup and shutdown are being executed against
a single H/W module, and a mailbox H/W module is totally
__independent__ of the registration of logical mailboxes.
So, an independent mutext should be used for startup and
shutdown.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
This patch checks if the mailbox user has assinged a valid
callback fuction before calling it.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
flush pending deferred works before freeing blk_queue to prevent
any attempt of access to blk_queue after it was freed
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
Free interrupt before freeing blk_queue to avoid
any attempt of access to blk_queue after it was freed.
Signed-off-by: Fernando Guzman Lugo <x0095840@ti.com>
Signed-off-by: Hiroshi DOYU <Hiroshi.DOYU@nokia.com>
These configurations are no longer useful as the systems they support
are covered by the generic omap3_defconfig
Signed-off-by:Vincent Sanders <vince@simtec.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
USBTLL Save-and-Restore is broken in 3630 ES1.0. Having it
enabled could result in incorrect register restores as
the OMAP exits off-mode. This could potentially result in
unexpected wakeup events.
(Refer 3630 errata ID i579)
This is fixed in ES1.1. So disable it for ES1.0s.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add revision detection for ES1.1 and ES1.2. Set default
revision as ES1.2.
Add CHIP_GE_OMAP3630ES1_1 to detect revisions 1.1 and later.
This is needed for at least one feature that is broken in
3630ES1.0 but exists on older (3430 ES3.1) and newer revisions.
Additionally, update some of the CHIP_GE_* macros to use other
macros for ease of maintenance.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Cc: Nishanth Menon <nm@ti.com>
Cc: Manjunatha GK <manjugk@ti.com>
[tony@atomide.com: update to remove fallthrough handling]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Do not forget to check the 'platform_device_add_data()' error code
in 'omap_device_build_ss()'.
Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
Acked-by: Nishanth Menon <nm@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Most OMAP3-based boards use exactly the same code for .map_io method in
the machine_desc structure.
This patch introduces omap3_map_io and updates board-* files to use it
as .map_io method.
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The only difference between them is the physical address of the
uart4 port, which is only present in 36xx chips.
We don't really need to care about keeping these 2 functions, since
the decision to use uart4 is more cleanly done later when we do have
access to omap_revision variable.
Signed-off-by: Sergio Aguirre <saaguirre@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
[tony@atomide.com: added comment for the uart4_phys]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Now we use a memory address to store the debug port info, So we need
to read/write this address when we choose DEBUG_LL. When MMU isn't
enable(I.E. the begining part of init stage of the linux kernel boot),
we need to access physical address instead of virtual address,
otherwise the kernel will crash.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Support HDMI in 720p mode.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
Add definitions for DV_CLKI and HDMI clocks, extend support for PLLC2 and some
other clocks.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
This function is necessary to ensure the detection of pen-down.
This patch support both QHD / WVGA pannel.
Tested-by: Tony SIM <chinyeow.sim.xt@renesas.com>
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
EXTAL1 is clocked at 26.0MHz
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
With these defines now it is possible to use
gpio_request(GPIO_FN_LCDC1_SELECT, NULL) or ...LCDC0... respectively to
switch between the two LCDC instances.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
On AP4EVB board, it is possible to select LCD panel type
which are parallel or MIPI by SW3, SW43 dip-switch.
This patch add parallel LCD settings and
select menu to Kconfig.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
* 'devel' of master.kernel.org:/home/rmk/linux-2.6-arm: (291 commits)
ARM: AMBA: Add pclk support to AMBA bus infrastructure
ARM: 6278/2: fix regression in RealView after the introduction of pclk
ARM: 6277/1: mach-shmobile: Allow users to select HZ, default to 128
ARM: 6276/1: mach-shmobile: remove duplicate NR_IRQS_LEGACY
ARM: 6246/1: mmci: support larger MMCIDATALENGTH register
ARM: 6245/1: mmci: enable hardware flow control on Ux500 variants
ARM: 6244/1: mmci: add variant data and default MCICLOCK support
ARM: 6243/1: mmci: pass power_mode to the translate_vdd callback
ARM: 6274/1: add global control registers definition header file for nuc900
mx2_camera: fix type of dma buffer virtual address pointer
mx2_camera: Add soc_camera support for i.MX25/i.MX27
arm/imx/gpio: add spinlock protection
ARM: Add support for the LPC32XX arch
ARM: LPC32XX: Arch config menu supoport and makefiles
ARM: LPC32XX: Phytec 3250 platform support
ARM: LPC32XX: Misc support functions
ARM: LPC32XX: Serial support code
ARM: LPC32XX: System suspend support
ARM: LPC32XX: GPIO, timer, and IRQ drivers
ARM: LPC32XX: Clock driver
...
Introduce a configuration struct for platform/board specific information
of Nokia DSI command mode panels, to be used in addition to struct
omap_dss_device (passed via the 'void *data' member).
Signed-off-by: Jani Nikula <ext-jani.1.nikula@nokia.com>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
The C99 specification states in section 6.11.5:
The placement of a storage-class specifier other than at the beginning
of the declaration specifiers in a declaration is an obsolescent
feature.
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@nokia.com>
Add a missing break at end of switch statement. At the moment it is a
fall through to WARN_ON(1) and return -EEXIST.
Signed-off-by: Thomas Weber <weber@corscience.de>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
add support for NAND, OneNAND, NOR on omap 3630-sdp board.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds NAND support to ZOOM2 board.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Vimal Singh <vimalsingh@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
rename board-sdp-flash.c(board-flash.c) and board-sdp.h(board-flash.h) to
used by other board e.g. zoom
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Board file modified for not to provide gpmc phys_base address to nand driver.
The gpmc_nand_init funciton is now used to detect the nand and required to
adopt _prob function as in nand/omap2.c
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch removes direct reference of gpmc address from generic nand platform code.
Nand platform code now uses wrapper functions which are implemented in gpmc module.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
few functions added in gpmc module and to be used by other drivers like NAND.
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
OMAP3530 CBB package can have GPIO126 muxed on 2 pins: mmc1_dat4 and
cam_strobe. This causes a problem with current multipath GPIO mux
handling, which muxes both pins as GPIO126 and makes the GPIO unusable.
Fix this by not muxing any pins if multipath GPIO is detected and
just print a warning instead. It's up to board files to set correct
mux using omap_mux_init_signal and pin name.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The devkit8000 boards often come with empty EEPROM thus without
valid ethernet MAC address. The DIE id to MAC formula is copied from
u-boot.
Signed-off-by: Kan-Ru Chen <kanru@0xlab.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
AM3505/3517 doesn't have IO wakeup capability, so we do not need to set
the bit OMAP3430_EN_IO and the bit OMAP3430_EN_IO_CHAIN in the register
PM_WKEN_WKUP when the system enters suspend state.
Tested on AM3517EVM and OMAP3530EVM.
Signed-off-by: Stanley.Miao <stanley.miao@windriver.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Omap DMA controller can prefetch data in advance in case of
destination synchronized data transfer. This may increase
performance when target HW block doesn't have fifo.
Data is waiting for transfer request in DMA fifo instead of read from memory.
Signed-off-by: Samu Onkalo <samu.p.onkalo@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
omap24xx_check_revision, omap3_check_features,
omap3_check_revision, omap4_check_revision, omap3_cpuinfo
are not used elsewhere, it should be static
Also fixes the following sparse warnings:
arch/arm/mach-omap2/id.c:105:13: warning: symbol 'omap24xx_check_revision'
was not declared. Should it be static?
arch/arm/mach-omap2/id.c:167:13: warning: symbol 'omap3_check_features'
was not declared. Should it be static?
arch/arm/mach-omap2/id.c:189:13: warning: symbol 'omap3_check_revision'
was not declared. Should it be static?
arch/arm/mach-omap2/id.c:270:13: warning: symbol 'omap4_check_revision'
was not declared. Should it be static?
arch/arm/mach-omap2/id.c:300:13: warning: symbol 'omap3_cpuinfo'
was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The original patch got truncated when applied from patchwork.kernel.org
as discussed at:
http://www.mail-archive.com/linux-omap@vger.kernel.org/msg28953.html
This patch supplies the missing chunks.
Signed-off-by: Steve Sakoman <sakoman@gmail.com>
[tony@atomide.com: added more info to the patch description]
Signed-off-by: Tony Lindgren <tony@atomide.com>
Fix GPIO numbers and smc91x for 2430sdp. The earlier code
had cut and paste errors from 3430sdp code. Also, 2430
has five GPIO banks for a total of 160 GPIO lines.
Signed-off-by: Tony Lindgren <tony@atomide.com>
This change adds in the necessary clocks and mux pins for UART
control on omap7xx devices. I also made a change in the serial
code to only try and initialize two UARTs in omap_serial_init, as
these devices don't have three.
Signed-off-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Recent DEBUG_LL and uncompress.h changes removed the check_port()
as pointed out by Cory Maccarrone <darkstar6262@gmail.com>.
This causes some boards to not boot, so add back the MDR1 register
check. The MDR1 register tells the mode of omap uart. Based on
an earlier patch by Cory Maccarrone <darkstar6262@gmail.com>.
Tested-by: Cory Maccarrone <darkstar6262@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds cpu hotplug support for OMAP4430. Only CPU inactive
state is supported as a low power state in the basic hot-plug support
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds a secure API to read AuxCoreBoot0 register to
check the cpu boot status. It also moves the other smc APIs
to common omap44xx-smc.S. This APIs should not be marked as
__INIT because we need these to be present for CPU hotplug
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for basic suspend doing a CPUx wfi
for OMAP4. All powerdomains are for now are kept programmed
in ON state.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Errata i202 (OMAP3430 - 1.12, OMAP3630 - 1.6):
UART module MDR1 register access can cause a dummy underrun
condition which could result in a freeze in the case of IrDA
communication or if used as UART, corrupted data.
Workaround is as follows for everytime MDR1 register is changed:
* setup all required UART registers
* setup MDR1.MODE_SELECT bit field
* Wait 5 L4 clk cycles + 5 UART functional clock cycles
* Clear the Tx and RX fifo using FCR register
Note: The following step is not done as I am assuming it is not
needed due to reconfiguration being done and there is no halted
operation perse.
* Read if required, the RESUME register to resume halted operation
Based on an earlier patch at:
http://git.omapzoom.org/?p=kernel/omap.git;a=commitdiff;h=42d4a342c009bd9727c100abc8a4bc3063c22f0c
Signed-off-by: Deepak K <deepak.k@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
introduce silicon specific quirks as a errata handling mechanism
as a start UART_ERRATA_FIFO_FULL_ABORT is used to handle the override
for fifo full condition for rx and tx.
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Remove the following sparse warnings by declaring attr as static:
arch/arm/mach-omap2/serial.c:627:1: warning: symbol 'dev_attr_sleep_timeout'
was not declared. Should it be static?
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Initialization of pointer should be done with NULL. Removes sparse
warnings:
arch/arm/mach-omap2/serial.c:566:17: warning: Using plain integer as NULL pointer
arch/arm/mach-omap2/serial.c:567:17: warning: Using plain integer as NULL pointer
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adds context save/restore for mcr register as state of mcr register
is lost after core off.
Signed-off-by: Govindraj R <govindraj.raja@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add initial support for the OMAP4 based Panda Board.
Signed-off-by: David Anders <x0132446@ti.com>
[tony@atomide.com: selected board by default in Kconfig]
Signed-off-by: Tony Lindgren <tony@atomide.com>
This patch adds support for GPIO LEDs present on OMAP4
SDP and Blaze boards. This basically adds platform data
required by leds-gpio driver
Signed-off-by: Hemanth V <hemanthv@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Adding board configuration for the tmp105
temperature sensor. The interface to the sensor
is I2C.
Signed-off-by: Shubhrajyoti D <shubhrajyoti@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The MMC1 and MMC2 cards have seperate LDO supplies. Current code assumes
that they are powered by same LDO.
This patch fixes the same and has VAUX1 as supply to MMC2 card.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Sukumar Ghorai <s-ghorai@ti.com>
Signed-off-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Tested-by: Kishore Kadiyala <kishore.kadiyala@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
This commit will enable usage of tsl2563 ambient light sensor on Nokia N900.
Signed-off-by: Ameya Palande <ameya.palande@nokia.com>
Signed-off-by: Mathias Nyman <mathias.nyman@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
With these and upcoming change to tpa6130a2 driver it's possible to add
support for the TPA6130A2 headphone amplifier.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
There is REGULATOR_SUPPLY macro available for initializing the struct
regulator_consumer_supply so use it where applicable (all other supplies
than vdds_sdi) as it improves the readability.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Acked-by: Eduardo Valentin <eduardo.valentin@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Proper operation of the tlv320aic3x audio codec requires that reset
sequencing is done in pair with supply voltages when using the regulator
framework. Add the codec reset gpio used in Nokia RX51 to tlv320aic3x
data.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
It seems that the battery cover sensor in Nokia N900 is powered from the
V28 domain. Now if this regulator is disabled it causes that the gpio 160
reads only zero which effectively causes uSD removal detection.
Currently the bootloader enabled V28 is kept on but this may change in the
future according to comment in
drivers/regulator/core.c: regulator_has_full_constraints.
Also if there are any consumers on the V28 domain doing regulator_enable
regulator_disable cycle the V28 will be disabled after that.
Prepare for these by defining the V28 as always_on regulator.
Signed-off-by: Jarkko Nikula <jhnikula@gmail.com>
Cc: Adrian Hunter <adrian.hunter@nokia.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add platform data for NAND and wifi, also setup all GPIOs
needed to use the wifi chip.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Update gpio-keys setup so it matches what is on default firmware.
Also make use of debounce feature in gpio-keys instead of setting it
explicitly, as gpio-keys is now capable of using hardware debounce on
OMAPs thanks to recent gpiolib changes.
Also fix a sparce warning along the way.
Signed-off-by: Grazvydas Ignotas <notasas@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc2 (third mmc controller) on the ZOOM3.
Signed-off-by: Ohad Ben-Cohen <ohadb@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Add board muxing to support the wlan wl1271 chip that is
hardwired to mmc2 (third mmc controller) on the ZOOM2.
Signed-off-by: Ohad Ben-Cohen <ohadb@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
The patch to add the apb_pclk to the AMBA/PrimeCell bus broke
RealView, since the clockdevice is not registered at probe() time.
This moves clock initialization to a core_initcall()
[rmk:moved before the problematical commit to avoid bisect problems]
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* master.kernel.org:/home/rmk/linux-2.6-arm:
cyber2000fb: fix console in truecolor modes
cyber2000fb: fix machine hang on module load
SA1111: Eliminate use after free
ARM: Fix Versatile/Realview/VExpress MMC card detection sense
ARM: 6279/1: highmem: fix SMP preemption bug in kmap_high_l1_vipt
ARM: Add barriers to io{read,write}{8,16,32} accessors as well
ARM: 6273/1: Add barriers to the I/O accessors if ARM_DMA_MEM_BUFFERABLE
ARM: 6272/1: Convert L2x0 to use the IO relaxed operations
ARM: 6271/1: Introduce *_relaxed() I/O accessors
ARM: 6275/1: ux500: don't use writeb() in uncompress.h
ARM: 6270/1: clean files in arch/arm/boot/compressed/
ARM: Fix csum_partial_copy_from_user()
__sa1111_remove always frees its argument, so the subsequent reference to
sachip->saved_state represents a use after free. __sa1111_remove does not
appear to use the saved_state field, so the patch simply frees it first.
A simplified version of the semantic patch that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
expression E,E2;
@@
__sa1111_remove(E)
...
(
E = E2
|
* E
)
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The MMC card detection sense has become really confused with negations
at various levels, leading to some platforms not detecting inserted
cards. Fix this by converting everything to positive logic throughout,
thereby getting rid of these negations.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
smp_processor_id() must not be called from a preemptible context (this
is checked by CONFIG_DEBUG_PREEMPT). kmap_high_l1_vipt() was doing so.
This lead to a problem where the wrong per_cpu kmap_high_l1_vipt_depth
could be incremented, causing a BUG_ON(*depth <= 0); in
kunmap_high_l1_vipt().
The solution is to move the call to smp_processor_id() after the call
to preempt_disable().
Originally by: Andrew Howe <ahowe@nvidia.com>
Signed-off-by: Gary King <gking@nvidia.com>
Acked-by: Nicolas Pitre <nico.as.pitre@linaro.org>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Introduce SHMOBILE_TIMER_HZ for SH-Mobile.
Allow users to select HZ on their system to
minimize potential timer drift. Use 128 Hz as
default to work well with the 32768 Hz RCLK.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
NR_IRQS_LEGACY is now defined in asm/irq.h,
so drop it in mach/irqs.h.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The ioread/iowrite accessors also need barriers as they're used in
place of readl/writel et.al. in portable drivers. Create __iormb()
and __iowmb() which are conditionally defined to be barriers dependent
on ARM_DMA_MEM_BUFFERABLE, and always use these macros in the accessors.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
When the coherent DMA buffers are mapped as Normal Non-cacheable
(ARM_DMA_MEM_BUFFERABLE enabled), buffer accesses are no longer ordered
with Device memory accesses causing failures in device drivers that do
not use the mandatory memory barriers before starting a DMA transfer.
LKML discussions led to the conclusion that such barriers have to be
added to the I/O accessors:
http://thread.gmane.org/gmane.linux.kernel/683509/focus=686153http://thread.gmane.org/gmane.linux.ide/46414http://thread.gmane.org/gmane.linux.kernel.cross-arch/5250
This patch introduces a wmb() barrier to the write*() I/O accessors to
handle the situations where Normal Non-cacheable writes are still in the
processor (or L2 cache controller) write buffer before a DMA transfer
command is issued. For the read*() accessors, a rmb() is introduced
after the I/O to avoid speculative loads where the driver polls for a
DMA transfer ready bit.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch is in preparation for a subsequent patch which adds barriers
to the I/O accessors. Since the mandatory barriers may do an L2 cache
sync, this patch avoids a recursive call into l2x0_cache_sync() via the
write*() accessors and wmb() and a call into l2x0_cache_sync() with the
l2x0_lock held.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This patch introduces readl*_relaxed()/write*_relaxed() as the main I/O
accessors (when __mem_pci is defined). The standard read*()/write*()
macros are now based on the relaxed accessors.
This patch is in preparation for a subsequent patch which adds barriers
to the I/O accessors.
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Don't use writeb() in uncompress.h, to avoid the following build errors
when the "Add barriers to the I/O accessors" series is applied. Use
__raw_writeb() instead.
arch/arm/boot/compressed/misc.o: In function `putc':
arch/arm/mach-ux500/include/mach/uncompress.h:41:
undefined reference to `outer_cache'
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
add global control registers definition header file for nuc900
Signed-off-by: Wan ZongShun <mcuos.com@gmail.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Update the compressed boot Makefile for ARM to
remove files during clean.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/lrg/voltage-2.6:
davinci: da850/omap-l138 evm: account for DEFDCDC{2,3} being tied high
regulator: tps6507x: allow driver to use DEFDCDC{2,3}_HIGH register
wm8350-regulator: fix wm8350_register_regulator error handling
ab3100: fix off-by-one value range checking for voltage selector
Per the da850/omap-l138 Beta EVM SOM schematic, the DEFDCDC2 and
DEFDCDC3 lines are tied high. This leads to a 3.3V IO and 1.2V CVDD
voltage.
Pass the right platform data to the TPS6507x driver so it can operate
on the DEFDCDC{2,3}_HIGH register to read and change voltage levels.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Liam Girdwood <lrg@slimlogic.co.uk>
This is the soc_camera support developed by Sascha Hauer for the i.MX27. Alan
Carvalho de Assis modified the original driver to get it working on more recent
kernels. I modified it further to add support for i.MX25. This driver has been
tested on i.MX25 and i.MX27 based platforms.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The GPIO registers need protection from concurrent access for operations that
are not atomic.
Cc: stable@kernel.org
Cc: Juergen Beisert <j.beisert@pengutronix.de>
Cc: Daniel Mack <daniel@caiaq.de>
Reported-by: rpkamiak@rockwellcollins.com
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add LPC32XX support in arch/arm/Kconfig and arch/arm/Makefile
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Platform support file for the PHY3250 mach id
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Misc support functions and prototypes used in the LPC32XX arch
and platforms
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Now that all arches have been converted over to use generic time via
clocksources or arch_gettimeoffset(), we can remove the GENERIC_TIME
config option and simplify the generic code.
Signed-off-by: John Stultz <johnstul@us.ibm.com>
LKML-Reference: <1279068988-21864-4-git-send-email-johnstul@us.ibm.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Common drivers for the LPC32XX used on all platforms
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Clock driver for the LPC32XX architecture
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Debug (printascii) and IRQ handler macros for the LPC32XX
arch
Signed-off-by: Kevin Wells <wellsk40@gmail.com>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
x86 calls machine_shutdown() from the various machine_*() calls which
take the machine down ready for halting, restarting, etc, and uses
this to bring the system safely to a point where those actions can be
performed. Such actions are stopping the secondary CPUs.
So, change the ARM implementation of these to reflect what x86 does.
This solves kexec problems on ARM SMP platforms, where the secondary
CPUs were left running across the kexec call.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The TWD local timers are unable to wake up the CPU when it is placed
into a low power mode, eg. C3. Therefore, we need to adapt things
such that the TWD code can cope with this.
We do this by always providing a broadcast tick function, and marking
the fact that the TWD local timer will stop in low power modes. This
means that when the CPU is placed into a low power mode, the core
timer code marks this fact, and allows an IPI to be given to the core.
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
All implementations of cpu_proc_fin() start by disabling interrupts
and then flush caches. Rather than have every processors proc_fin()
implementation do this, move it out into generic code - and move the
cache flush past setup_mm_for_reboot() (so it can benefit from having
caches still enabled.)
This allows cpu_proc_fin() to become independent of the L1/L2 cache
types, and eventually move the L2 cache flushing into the L2 support
code.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Statuses 3 (0b00011) and 6 (0x00110) of DFSR are Access Flags faults on
ARMv6K and ARMv7. Let's patch fsr_info[] at runtime if we are on ARMv7
or later.
Unfortunately, we don't have runtime check for 'K' extension, so we
can't check for it.
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
On ARM one Linux PGD entry contains two hardware entries (see page
tables layout in pgtable.h). We normally guarantee that we always
fill both L1 entries. But create_mapping() doesn't follow the rule.
It can create inidividual L1 entries, so here we have to call
pmd_none() check in do_translation_fault() for the entry really
corresponded to address, not for the first of pair.
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add one more parameter to hook_fault_code() to be able to set 'code'
field of struct fsr_info.
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
POSIX specify to use signal SIGBUS with code BUS_ADRALN for invalid
address alignment.
Signed-off-by: Kirill A. Shutemov <kirill@shutemov.name>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
SPARSE_IRQ doesn't need to be a visible option, only those platforms
supporting that will select it.
Signed-off-by: Eric Miao <eric.miao@canonical.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
The DMA coherent remap area is used to provide an uncached mapping
of memory for coherency with DMA engines. Currently, we look for
any free hole which our allocation will fit in with page alignment.
However, this can lead to fragmentation of the area, and allows small
allocations to cross L1 entry boundaries. This is undesirable as we
want to move towards allocating sections of memory.
Align allocations according to the size, limiting the alignment between
the page and section sizes.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
We don't need our own implementation of this, use the generic
library implementation instead.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
This changes the TCM handling so that a fixed area is reserved at
0xfffe0000-0xfffeffff for TCM. This areas is used by XScale but
XScale does not have TCM so the mechanisms are mutually exclusive.
This change is needed to make TCM detection more dynamic while
still being able to compile code into it, and is a must for the
unified ARM goals: the current TCM allocation at different places
in memory for each machine would be a nightmare if you want to
compile a single image for more than one machine with TCM so it
has to be nailed down in one place.
Signed-off-by: Linus Walleij <linus.walleij@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
WARNING: vmlinux.o(.text+0xbf38): Section mismatch in reference from the function pci_versatile_scan_bus() to the function .devinit.text:pci_scan_bus_parented()
The function pci_versatile_scan_bus() references
the function __devinit pci_scan_bus_parented().
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add the platform data to enable AB8500 interrupt support.
Acked-by: Linus Walleij <linus.walleij@stericsson.com>
Acked-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com>
Signed-off-by: Rabin Vincent <rabin.vincent@stericsson.com>
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Add omap_pm_set_min_clk_rate(). This constraint is meant for use by
device drivers to translate a certain device-specific performance
constraint (e.g., "minimum polygons per second") to a clock rate for
the driver's device, given the driver's intimate knowledge of the
device hardware (e.g., device type, device hardware revision, firmware
revision, etc.) From a general PM core perspective, clock rate is
probably the closest general analog to "performance" that is
available, but the exact mapping from a use-case-specific performance
constraint to clock rate must be done by the driver. Drivers intended for
upstream merging shouldn't hardcode specific clock rates in their code
without basing those rates on some performance criteria requested through
the driver's subsystem (ideally, from userspace).
Imre Deak <imre.deak@nokia.com> described the need and use-case for
this constraint, and discussed the implementation - thanks, Imre.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Imre Deak <imre.deak@nokia.com>
Add return values to the PM constraint functions. This allows the PM
core to provide feedback to the caller if a constraint is not
possible. Update the one upstream user of omap_pm_set_max_mpu_wakeup_lat()
to add a compatibility wrapper, needed until the driver is changed.
Update some of the documentation to conform more closely to kerneldoc style.
Add an additional device parameter to omap_pm_set_max_dev_wakeup_lat()
to identify the device requesting the constraint. This is so repeated calls
to omap_pm_set_max_dev_wakeup_lat() with the same requesting device can
override the device's previously-set constraint. Also, it allows the PM
core to make a decision as to whether or not the constraint should be
satisfied, based on the caller's identity.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Update some minor documentation issues and update copyright for
omap_device/omap_hwmod code.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Add omap_device_get_mpu_rt_va(). This is intended to be used by
device drivers (currently, via a struct platform_data function
pointer) to retrieve their corresponding device's virtual base address
that the MPU should use to access the device. This is needed because
the omap_hwmod code does its own ioremap(), in order to gain access to
the module's OCP_SYSCONFIG register.
Add omap_hwmod_get_mpu_rt_va(). omap_device_get_mpu_rt_va() calls this
function to do the real work.
While here, rename struct omap_hwmod._rt_va to struct
omap_hwmod._mpu_rt_va, to reinforce that it refers to the MPU's
register target virtual address base (as opposed to, for example, the
L3's).
In the future, this belongs as a function in an omap_bus, so it is not
necessary to call this through a platform_data function pointer.
The use-case for this function was originally presented by Santosh
Shilimkar <santosh.shilimkar@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Add IVA1 hwmod data for OMAP2420 and IVA2 hwmod data for 2430. The data
is based on Benoît Cousson's hwmod data for the OMAP3 IVA blocks.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Add hwmod data for IVA2 module on OMAP3.
Naming of "iva" instead of "iva2" to be aligned with OMAP4 naming done
by Benoit Cousson.
Cc: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Replace all the struct that contain l3 with l3_main in order
to be consistent with the OMAP4 naming convention.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add a new hwmod class for IVA devices. To be used when hwmods
are created for IVA2 on OMAP3.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Benoît Cousson <b-cousson@ti.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Create simple omap_devices for the main processors and busses.
This is required to support the forth-coming device-based OPP
approach, where OPPs are managed and tracked at the device level.
Also, move these common PM init functions into a common_pm_init call
that is called as a device_initcall(). The PM init is done at this level
to ensure that the driver core is initialized before initialized.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[paul@pwsan.com: sparse warnings cleaned up; newly-created functions moved
from mach-omap2/io.c to mach-omap2/pm.c; newly-created functions renamed
to start with "omap2" rather than "omap"]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
The omap_hwmod struct has a field to track the omap_device that is
attached to it, but it was not being assigned. Fix by assigning omap_device
pointer when omap_device is built.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
[paul@pwsan.com: use an array index rather than pointer arithmetic]
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Enable omap_device layer support for OMAP4, so that drivers can
use them to enable/idle/shutdown devices.
Signed-off-by: Rajendra Nayak <rnayak@ti.com>
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On kernels that don't use the omap_device_enable() calls to enable
devices, leave all on-chip devices enabled in hwmod _setup().
Otherwise, accesses to those devices are likely to fail, crashing the
system. It's expected that kernels built without CONFIG_PM_RUNTIME
will be the primary use-case for this. This functionality is
controlled by adding an extra parameter to omap_hwmod_late_init().
This patch is based on the patch "OMAP: hwmod: don't auto-disable
hwmod when !CONFIG_PM_RUNTIME" by Kevin Hilman
<khilman@deeprootsystems.com>.
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Some hwmods may need to be idled/enabled in atomic context, so
non-locking versions of these functions are required.
Most users should not need these and usage of theses should be
controlled to understand why access is being done in atomic context.
For this reason, the non-locking functions are only exposed at the
hwmod level and not at the omap-device level.
The use-case that led to the need for the non-locking versions is
hwmods that are enabled/idled from within the core idle/suspend path.
Since interrupts are already disabled here, the mutex-based locking in
hwmod can sleep and will cause potential deadlocks.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
In the lastest OMAP4 hwmod data file, the _hwmod was removed
in order to save some memory space and because it does not
bring a lot.
Align OMAP2420, 2430 and 3430 data files with the same convention.
Signed-off-by: Benoit Cousson <b-cousson@ti.com>
Cc: Rajendra Nayak <rnayak@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Since these hwmods do not have IDLEST, set the HWMOD_NO_IDLEST flag,
otherwise _enable() will fail due to failing _wait_target_ready().
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
On OMAP24xx, the polarity for the IDLEST bits is opposite of OMAP3.
The mask used to check this was using the bit position instead of the
bit mask.
This patch fixes the problem by using the bit mask instead of the bit
field.
Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Convert most of the magic numbers in mach-omap1/clock_data.c to use
macros. Clean up a few comments to conform with Documentation/CodingStyle.
Mark the current clkops_uart as being OMAP16xx-only, and add some comments
to indicate that it does not belong there, for future cleanup.
This patch should not cause any functional changes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add KConfig entry for one of the OMAP1 DVFS rates that was missing it.
Based on the surrounding rate KConfigs and the oscillator frequency,
this patch marks it as valid for all OMAP1 platforms -- Richard,
Tuukka, Tony, perhaps you can comment if this does not look right?
In the long term, all of these CONFIG_OMAP_ARM_*MHZ should be removed.
The OPP settings should be associated with the platform information in
the structure data (perhaps by extending the omap_chip defines). The
selection of which rates to use should be handled at runtime; rates
that are impossible due to xtal frequency mismatch or SoC-type
mismatch should not be included. If implemented correctly, this
should save some CPU time and some memory on OMAP1 kernels.
Reported-by: Christoph Egger <siccegge@cs.fau.de>
Reported-by: The VAMOS Research Project <vamos@i4.informatik.uni-erlangen.de>
Cc: Marek Vasut <marek.vasut@gmail.com>
Cc: Richard Woodruff <r-woodruff2@ti.com>
Cc: Tuukka Tikkanen <tuukka.tikkanen@nokia.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Add kerneldoc for struct clk, struct clksel_rate, struct clksel. Move
flag macros for struct clk.flags and struct clksel_rate.flags closer
to the structures.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
We need to wait on the IDLEST bit after the clocks are enabled
before attempting to access any register.
Currently, the USBTLL i-clock ops uses the clkops_omap2_dflt_wait,
while the USBTLL f-clock ops uses clkops_omap2_dflt. If the
i-clock is enabled first, the clkops_omap2_dflt_wait is
short-circuited as the companion f-clock is not enabled.
This can cause a data abort if the IDLEST has not transitioned,
and we try to access a USBTLL register.
Since the USBTLL i-clock and f-clock could be enabled in any order,
this is a bug. Fix it by changing the clkops for the f-clock.
Signed-off-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Commit 3fea60261e ("Input: twl40300-keypad - fix handling of "all
ground" rows") broke compilation as I managed to use non-existent
keycodes.
Reported-by: Arjan van de Ven <arjan@infradead.org>
Signed-off-by: Dmitry Torokhov <dtor@mail.ru>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
CPUIMX51 is build around Freescale's i.MX515 and has up to
512MB of RAM, NAND Flash, Ethernet, USB Host with 4 ports
hub, USB OTG, ST16554 Quad UART on nCS1, I2C RTC ...
MBIMX51 adds LEDS, Keypad, TSC2007 touchscreen controler ...
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The commit 9a763bf "get rid of mxc_gpio_init" changed gpio_init
and irq_init sequence. Usually we will call set_irq_chained_handler
in gpio_init functions, this should be called after the irq_init
called, otherwise the chained irq can't get propoer irq_chip and this
irq will remain masked even we called set_irq_chained_handler.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Tested-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
as per suggested by Sascha
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
This patch fixes the following Kconfig warning :
"arch/arm/mach-mx25/Kconfig:18:warning: choice value used outside its
choice group
Signed-off-by: Eric Bénard <eric@eukrea.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
In order to make this patch compile, even if the flexcan driver with
it's header defining the platform data isn't merged yet, two ifdefs have
been added. They effect that the "imx_add_flexcan" function results in a
no-op function if the driver hasn't been activated.
These ifdefs can be removed after the flexcan driver has been merged.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The i.MX51 generates 2 IRQ for each GPIO bank : one for gpio 0 to 15
and one for gpio 16 to 31.
Actually only the lower IRQ is registered so register the second one.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
the i2c_board_info structure landed into the SPI #if/#endif
which is wrong.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
DEBUG_LL is actually broken on i.MX25, this patch fix it.
Signed-off-by: Eric Bénard <eric@eukrea.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add keymaps and imx_keypad device registration for imx51_3ds board.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
add imx_keypad platform device definition and clocks for mx51
platforms.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
3-stack is a reference board from Freescale for their i.MX51 SoC.
Add board definition, Kconfig and Makefile to enable Freescale 3-stack
board.
Boot tested on a i.MX51 3-stack Rev2.0 board
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
mx27_3ds: add support for the keypad
Signed-off-by: Rogerio Pimentel <rogerio.pimentel@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Because we add a 3ds debug board support in mxc level, we remove
those redundant codes from board level.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The debug board is little different for all mxc 3-stack(PDK)
platforms, it is possible here to add a common implementation to
support this board.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
There are some more conflicts than detected by git, namely support for
the newly added cpuimx machines needed to be converted to dynamic device
registration.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Conflicts:
arch/arm/mach-imx/Makefile
arch/arm/mach-imx/devices.c
arch/arm/mach-imx/devices.h
arch/arm/mach-imx/eukrea_mbimx27-baseboard.c
arch/arm/mach-mx2/Kconfig
arch/arm/mach-mx25/Makefile
arch/arm/mach-mx25/devices.c
arch/arm/plat-mxc/include/mach/mx25.h
arch/arm/plat-mxc/include/mach/mxc_nand.h
cleaned up some duplicated mxc_gpio_mode calls and move the correpsonding
pin multiplexing either into the initial pin config table or ifdef blocks.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
this one adds the frambuffer device and a TFT panel to the PhyCard-S
(pca100) board.
Signed-off-by: Luotao Fu <l.fu@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
These GPIO bank offsets are useful when define a gpio number.
E.G. when GPIO PORTC pin 6 is used for irq request pin of external
expanding device, we can define it like:
#define EXP_PARENT_IRQ_PIN (GPIO_PORTC + 6)
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Add UART2 CTS/RTS and UART3 RXD/TXD pad definitons for imx51_3ds board,
add GPIO_1_6 definiton because this pin is used as a CPLD parent irq
request pin on imx51_3ds board.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
For pad EIM_D27 to work in UART3_RTS mode, the input path should be
3 instead of 0; for pad USBH1_STP to work in GPIO_1_27 mode, the mux
value should be 2 instead of 8.
Signed-off-by: Jason Wang <jason77.wang@gmail.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The pads capable of being used as GPIOs had their pad-name and mode-name
switched. Also, fix the following:
- Whitespace fixes
- Replace IOMUX_CONFIG_ALTn with 'n'
Signed-off-by: Amit Kucheria <amit.kucheria@canonical.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
The information in the i.MX25 Reference Manual is lacking. Add information from
the Freescale BSP.
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Marek Szyprowski