Add a driver for the SDIO/MMC host found on the Amlogic Meson SoCs. This
is an MMC controller which provides an interface between the application
processor and various memory cards. It supports the SD specification
v2.0 and the eMMC specification v4.41.
The controller provides an internal "mux" which allows connecting up to
three MMC devices to it. Only one device can be used at a time though
since the registers are shared across all devices. The driver takes care
of synchronizing access (similar to the dw_mmc driver).
The maximum supported bus-width is 4-bits.
Amlogic's GPL kernel sources call the corresponding driver "aml_sdio" to
differentiate it from the other MMC controller in (at least the Meson8
and Meson8b) the SoCs (they call the other drivers aml_sdhc and
aml_sdhc_m8, which seem to support a bus-width of up to 8-bits). This
means that there are three different MMC host controller IP blocks from
Amlogic (each of them with completely own register layout and features):
- "SDIO": 1 and 4 bit bus width, support for high-speed modes up to
UHS-I SDR50, part of Meson6, Meson8 and Meson8b (the driver from this
patch targets this controller)
- "SDHC": 1, 4 and 8 bit bus width, compatible with standard iNAND
interface, support for speeds up to HS200 and MMC spec up to version
4.5x, part of Meson8 and Meson8b SoCs (there is no mainline driver
for this controller yet)
- "SDEMMC": 1, 4 and 8 bit bus width, support for speeds up to HS400
and MMC spec up to version 5.0, part of the Meson GX (64-bit) SoCs
(supported by the meson-gx MMC host driver)
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Without the ThunderX/OcteonTx GPIO driver the MMC driver
would not power up any MMC devices. Therefore add a
dependency to the GPIO driver and remove the unneeded GPIOLIB
dependency.
Signed-off-by: Jan Glauber <jglauber@cavium.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable CONFIG_MMC_SDHCI_IO_ACCESSORS so that SDHC controller specific
register read and write APIs, if registered, can be used.
Signed-off-by: Vijay Viswanath <vviswana@codeaurora.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Create a new sdhci-omap driver to configure the eMMC/SD/SDIO controller
in TI's OMAP SoCs making use of the SDHCI core library. For OMAP specific
configurations, populate sdhci_ops with OMAP specific callbacks and use
SDHCI quirks.
Enable only high speed mode for both SD and eMMC here and add other
UHS mode support later.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
MMC_DEBUG was moved and one letter got strangely capitalized.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It does not make sense for qcom dml code to be a seperate module, as
this has just 2 helper functions specific to qcom, and used directly by
mmci driver, so just compile this along with main mmci driver.
This would also fix issues arrising due to Kconfig combinations between
mmci and qcom dml.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I cannot see why this is needed. kmap() should be safe in this case.
Signed-off-by: Ian Molton <ian@mnementh.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We have removed all code depending on CONFIG_MMC_DEBUG
from mmc core now. So it's safe to make CONFIG_MMC_DEBUG
just for host drivers only and we expect to kill this option
in the future.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a new variant of the SDHI driver to support R-Car Gen3 with DMA via
on-chip bus mastering. Since the DMAC is in a part of the SDHI module it
is not suitable to be used via DMA Engine.
Clearing of DM_CM_INFO1 after DMA thanks to Dirk Behme
Cc: Dirk Behme <dirk.behme@de.bosch.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Rename the source file SDHI. A follow-up patch will make it a library
file used by a different top-level module file.
The name "renesas" is chosen as the SDHI driver is applicable to a wider
range of SoCs than SH-Mobile it seems to be a more appropriate name.
However, the SDHI driver source itself, is left as sh_mobile_sdhi to
avoid unnecessary churn.
the name "core" was chosen to reflect the desired role of this file,
to provide core functionality to the sdhi driver. A follow-up patch will
move the file into that role.
Internal symbols have also been renamed to reflect the filename change.
The .name member of struct platform_driver and parameter to
MODULE_ALIAS() have not been changed in order to avoid the complication
of potentially breaking SH SoCs which still use platform drivers.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
AVR32 is gone. Now it's time to clean up the driver by removing
leftovers that was used by AVR32 related code.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add platform driver for Octeon SOCs.
Signed-off-by: Steven J. Hill <Steven.Hill@cavium.com>
Signed-off-by: David Daney <david.daney@cavium.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add Xenon eMMC/SD/SDIO host controller core functionality.
Add Xenon specific initialization process.
Add Xenon specific mmc_host_ops APIs.
Add Xenon specific register definitions.
Add CONFIG_MMC_SDHCI_XENON support in drivers/mmc/host/Kconfig.
Marvell Xenon SDHC conforms to SD Physical Layer Specification
Version 3.01 and is designed according to the guidelines provided
in the SD Host Controller Standard Specification Version 3.00.
Signed-off-by: Hu Ziji <huziji@marvell.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The 2835 has two SD controllers: The Arasan sdhci controller (supported
by the iproc driver) and a custom sdhost controller. This patch adds a
driver for the latter.
The sdhci controller supports both sdcard and sdio. The sdhost
controller supports the sdcard only, but has better performance. Also
note that the rpi3 has sdio wifi, so driving the sdcard with the sdhost
controller allows to use the sdhci controller for wifi support.
The configuration is done by devicetree via pin muxing. Both SD
controller are available on the same pins (2 pin groups = pin 22 to 27 +
pin 48 to 53). So it's possible to use both SD controllers at the same
time with different pin groups.
The code was originally written by Phil Elwell in the downstream
Rasbperry Pi tree. In preparation for the upstream merge it was
cleaned up and the code base was moderized by Eric Anholt, Stefan
Wahren and Gerd Hoffmann.
Signed-off-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Gerd Hoffmann <kraxel@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This platform driver adds initial support for the DW host controller
found on ZTE SoCs.
It has been tested on ZX296718 EVB board currently. More support on
timing tuning will be added when hardware is available.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a driver for the Cadence SD4HC SD/SDIO/eMMC Controller.
For SD, it basically relies on the SDHCI standard code.
For eMMC, this driver provides some callbacks to support the
hardware part that is specific to this IP design.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I see no override of read/write callbacks in sdhci-of-at91.c.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The eSDHC of T4240-R1.0-R2.0 has incorrect vender version and spec version.
Acturally the right version numbers should be VVN=0x13 and SVN = 0x1.
This patch adds the GUTS driver support for eSDHC driver to match SoC.
And fix host version to avoid that incorrect version numbers break down
the ADMA data transfer.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Scott Wood <oss@buserror.net>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Initial support for the SD/eMMC controller in the Amlogic S905/GX*
family of SoCs.
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Some SD/eMMC PHYs (like the PHY from Arasan that is designed to work
with arasan,sdhci-5.1) need to know the card clock in order to function
properly. Let's add the ability to expose this clock. Any PHY that
needs to know the clock rate can add a reference and query the clock
rate.
At the moment we register a CLK_GET_RATE_NOCACHE clock that simply
allows querying the clock. This allows us to be less intrusive with
regards to the main SDHCI driver, which has complex logic for adjusting
the SD clock. Right now we always fully power cycle the PHY when the
clock changes and that gives the PHY a good chance to query our clock.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add SDHCI driver for Broadcom BRCMSTB SoCs.
This driver works with all ARM based SoCs and the 7425, 7429
and 7435 MIPS based SoCs.
The driver disables all UHS speed modes by default and relies
on the Device Tree node properties to enable these modes for
SoC/Board combinations that support them.
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The sdhci-bcm2835 is no more needed since it has been replaced
by sdhci-iproc.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There is no support for this platform in the kernel anymore. Make the
Kconfig text more generic, so it won't get stale anymore.
Reported-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Baytrail eMMC/SD/SDIO host controllers have been known to
hang. A change to a hardware setting has been found to
reduce the occurrence of such hangs. This patch ensures
the correct setting.
This patch applies cleanly to v4.4+. It could go to
earlier kernels also, so I will send backports to the
stable list in due course.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org # v4.4+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Make use of ARCH_RENESAS in place of ARCH_SHMOBILE.
This is part of an ongoing process to migrate from ARCH_SHMOBILE to
ARCH_RENESAS the motivation for which being that RENESAS seems to be a more
appropriate name than SHMOBILE for the majority of Renesas ARM based SoCs.
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Registers are 64bit apart, so we refactor bus_shift handling a little and set
it based on the DT compatible. Also, EXT_ACC is different. It has been tested
on a Salvator-X (Gen3) and, to check for regressions, on a Lager (Gen2).
Signed-off-by: Ai Kyuse <ai.kyuse.uw@renesas.com>
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This driver supports the SDHCI host controller found on a PIC32.
Signed-off-by: Andrei Pistirica <andrei.pistirica@microchip.com>
Signed-off-by: Joshua Henderson <joshua.henderson@microchip.com>
Cc: Ralf Baechle <ralf@linux-mips.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Scott Branden from Broadcom said that the BCM2835 eMMC IP core is
very similar to IPROC and share most of the quirks. So use this driver
instead of separate one.
The sdhci-iproc contains a better workaround for the clock domain
crossing problem which doesn't need any delays. This results in a
better write performance.
Btw we get the rid of the SDHCI_CAPABILITIES hack in the sdhci_readl
function.
Suggested-by: Scott Branden <sbranden@broadcom.com>
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <sbranden@broadcom.com>
Acked-by: Stephen Warren <swarren@wwwdotorg.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I don't see a reason why a host driver should depend on the card driver.
It also prevents that we can use the mmc_test driver. So, remove it.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
There are no in-kernel users of the MVSDIO platform data method
(instantiating from a board file) so just delete this code and
make this a DT-only driver. We depend on OF and check that we have
an OF node in probe().
Cc: Nicolas Pitre <nico@fluxnic.net>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Nicolas Pitre <nico@linaro.org>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Enable omap_hsmmc for Keystone 2 architecture which reuses the HSMMC
IP found on OMAP platforms.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
DesignWare MMC Controller can supports two types of DMA
mode: external dma and internal dma. We get a RK312x platform
integrated dw_mmc and ARM pl330 dma controller. This patch add
edmac ops to support these platforms. I've tested it on RK31xx
platform with edmac mode and RK3288 platform with idmac mode.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The driver depends on GOLDFISH but there isn't a build dependency
so it's a good idea to allow the driver to always be built when the
COMPILE_TEST option is enabled.
That way, the driver can be built with a config generated by make
allyesconfig and check if a patch would break the build.
Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Freescale eSDHC driver now supports both little-endian and
big-endian mode eSDHC IPs for ARM and PPC. So, MMC_SDHCI_OF_ESDHC
option needs to be reconfigured.
Signed-off-by: Yangbo Lu <yangbo.lu@freescale.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Introduce driver for he Atmel SDMMC available on sama5d2. It is a sdhci
compliant controller.
Signed-off-by: Ludovic Desroches <ludovic.desroches@atmel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
chips have some issues for version and capbility registers, here we fake
them.
Signed-off-by: Weijun Yang <Weijun.Yang@csr.com>
Signed-off-by: Barry Song <Baohua.Song@csr.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
We've got a fairly large cleanup branch this time. The bulk of this is removal
of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining board-file based
support
- OMAP removes legacy board files for three more platforms
- Removal of non-DT mach-msm, newer Qualcomm platforms now live in mach-qcom
- Freescale i.MX25 also removes non-DT platform support
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=BV8A
-----END PGP SIGNATURE-----
Merge tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups from Olof Johansson:
"We've got a fairly large cleanup branch this time. The bulk of this
is removal of non-DT platforms of several flavors:
- Atmel at91 platforms go full-DT, with removal of remaining
board-file based support
- OMAP removes legacy board files for three more platforms
- removal of non-DT mach-msm, newer Qualcomm platforms now live in
mach-qcom
- Freescale i.MX25 also removes non-DT platform support"
Most of the rest of the changes here are fallout from the above, i.e. for
example removal of drivers that now lack platforms, etc.
* tag 'armsoc-cleanup' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (58 commits)
mmc: Remove msm_sdcc driver
gpio: Remove gpio-msm-v1 driver
ARM: Remove mach-msm and associated ARM architecture code
ARM: shmobile: cpuidle: Remove the pointless default driver
ARM: davinci: dm646x: Add interrupt resource for McASPs
ARM: davinci: irqs: Correct McASP1 TX interrupt definition for DM646x
ARM: davinci: dm646x: Clean up the McASP DMA resources
ARM: davinci: devices-da8xx: Add support for McASP2 on da830
ARM: davinci: devices-da8xx: Clean up and correct the McASP device creation
ARM: davinci: devices-da8xx: Add interrupt resource to McASP structs
ARM: davinci: devices-da8xx: Add resource name for the McASP DMA request
ARM: OMAP2+: Remove legacy support for omap3 TouchBook
ARM: OMAP3: Remove legacy support for devkit8000
ARM: OMAP3: Remove legacy support for EMA-Tech Stalker board
ARM: shmobile: Consolidate the pm code for R-Car Gen2
ARM: shmobile: r8a7791: Correct SYSCIER value
ARM: shmobile: r8a7790: Correct SYSCIER value
ARM: at91: remove old setup
ARM: at91: sama5d4: remove useless map_io
ARM: at91: sama5 use SoC detection infrastructure
...
This driver is orphaned now that mach-msm has been removed.
Delete it.
Cc: Chris Ball <chris@printf.net>
Cc: David Brown <davidb@codeaurora.org>
Cc: Bryan Huntsman <bryanh@codeaurora.org>
Cc: Daniel Walker <dwalker@fifo99.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Kumar Gala <galak@codeaurora.org>
This driver is used on SoCs which are using CONFIG_OF. By adding a
compile dependency in the Kconfig, it enables us to simplify some code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
It was brought to my attention that the sdhci-pxav3 driver is needed
on a few more ARM machines than I initially thought. Add the missing
architectures to the dependency list.
Credits to Peter Robinson for noticing my mistake and reporting.
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Chris Ball <chris@printf.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Cc: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
The PPC_OF is a ppc specific option which is used to mean that the
firmware device tree access functions are available. Since all the
ppc platforms have a device tree, it is aways set to 'y' for ppc.
So it makes no sense to keep a such option in the current kernel.
Replace it with PPC.
Signed-off-by: Kevin Hao <haokexin@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
I seem to understand that the sdhci-pxav3 and sdhci-pxav2 drivers are
only needed on the MMP architecture. So add a hardware dependency on
ARCH_MMP, so that other users don't get to build useless drivers.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Chris Ball <chris@printf.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Haojian Zhuang <haojian.zhuang@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Let MMC_SDHCI_BIG_ENDIAN_32BIT_BYTE_SWAPPER depend on MMC_SDHCI. Not
only this is more correct, but this also avoids breaking the alignment
of all other MMC_SDHCI_* options in menuconfig.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Chris Ball <chris@printf.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: Albert Herranz <albert_herranz@yahoo.es>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Carlo Caione