Device stopped to tuning some channels after regmap conversion.
Reason is that regmap_update_bits() works a bit differently for
partially volatile registers than old homemade routine. Return
back to old routine in order to fix issue.
Fixes: 478932b160
Cc: <stable@kernel.org> # 4.2+
Reported-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Tested-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Add lock to prevent concurrent access for control message as control
message function uses shared buffer. Without the lock there may be
remote control polling which messes the buffer causing IO errors.
Increase buffer size and add check for maximum supported message
length.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=103391
Fixes: c56222a6b2 ("[media] rtl28xxu: move usb buffers to state")
Cc: <stable@vger.kernel.org> # 4.0+
Signed-off-by: Antti Palosaari <crope@iki.fi>
Fixes the following randconfig problem:
drivers/built-in.o: In function `v4l2_flash_release':
(.text+0x12204f): undefined reference to `v4l2_async_unregister_subdev'
drivers/built-in.o: In function `v4l2_flash_release':
(.text+0x122057): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o: In function `v4l2_flash_close':
v4l2-flash-led-class.c:(.text+0x12208f): undefined reference to `v4l2_fh_is_singular'
v4l2-flash-led-class.c:(.text+0x1220c8): undefined reference to `__v4l2_ctrl_s_ctrl'
drivers/built-in.o: In function `v4l2_flash_open':
v4l2-flash-led-class.c:(.text+0x12227f): undefined reference to `v4l2_fh_is_singular'
drivers/built-in.o: In function `v4l2_flash_init_controls':
v4l2-flash-led-class.c:(.text+0x12274e): undefined reference to `v4l2_ctrl_handler_init_class'
v4l2-flash-led-class.c:(.text+0x122797): undefined reference to `v4l2_ctrl_new_std_menu'
v4l2-flash-led-class.c:(.text+0x1227e0): undefined reference to `v4l2_ctrl_new_std'
v4l2-flash-led-class.c:(.text+0x122826): undefined reference to `v4l2_ctrl_handler_setup'
v4l2-flash-led-class.c:(.text+0x122839): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x1228e2): undefined reference to `v4l2_subdev_init'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x12293b): undefined reference to `v4l2_async_register_subdev'
drivers/built-in.o: In function `v4l2_flash_init':
(.text+0x122949): undefined reference to `v4l2_ctrl_handler_free'
drivers/built-in.o:(.rodata+0x20ef8): undefined reference to `v4l2_subdev_queryctrl'
drivers/built-in.o:(.rodata+0x20f10): undefined reference to `v4l2_subdev_querymenu'
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Cc: Sakari Ailus <sakari.ailus@iki.fi>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
When reading the firmware and sending commands, the length must
be bounds checked to avoid overrunning the size of the command
buffer and smashing the stack if the firmware is not in the expected
format:
si2168 11-0064: found a 'Silicon Labs Si2168-B40'
si2168 11-0064: downloading firmware from file 'dvb-demod-si2168-b40-01.fw'
si2168 11-0064: firmware download failed -95
Kernel panic - not syncing: stack-protector: Kernel stack is corrupted in: ffffffffa085708f
Add the proper check.
Cc: stable@kernel.org
Reported-by: Stuart Auchterlonie <sauchter@redhat.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
When reading the firmware and sending commands, the length
must be bounds checked to avoid overrunning the size of the command
buffer and smashing the stack if the firmware is not in the
expected format. Add the proper check.
Cc: stable@kernel.org
Signed-off-by: Laura Abbott <labbott@fedoraproject.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This driver doesn't claim the IR transmitter to be wakeup source. It
even disables the clock and the IR during suspend-resume cycle.
This patch removes yet another misuse of IRQF_NO_SUSPEND.
Cc: Patrice Chotard <patrice.chotard@st.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Guoxiong Yan <yanguoxiong@huawei.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Acked-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
The variable err was never initialized, that means we had been checking
a garbage value in the for loop. Moreover if the segment is not outside
the firmware file then also we have been returning the garbage.
Initialize it to 0 so that on success we return the value and no need to
check in the for loop also as it is initially 0 and whenever that value
changes we have done a break from the loop.
Signed-off-by: Sudip Mukherjee <sudip@vectorindia.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
static analysis with cppcheck detected the following error:
[drivers/media/platform/sti/c8sectpfe/c8sectpfe-core.c:1210]:
(error) Uninitialized variable: ret
ret is never initialised, so garbage is being returned. Instead
return the error return from the call of request_firmware_nowait
Signed-off-by: Colin Ian King <colin.king@canonical.com>
If CONFIG_DVB_LNBH25 is disabled, a stub static inline function is
defined that just prints a warning about the driver being disabled
but the function return type was wrong which caused a build error.
Fixes: e025273b86 ("[media] lnbh25: LNBH25 SEC controller driver")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
If CONFIG_DVB_HORUS3A is disabled a stub static inline function is
defined that just prints a warning about the driver being disabled
but the function parameters were wrong which caused a build error.
Fixes: a5d32b3582 ("[media] horus3a: Sony Horus3A DVB-S/S2 tuner driver")
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TEFw
-----END PGP SIGNATURE-----
Merge tag 'media/v4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
"A series of patches that move part of the code used to allocate memory
from the media subsystem to the mm subsystem"
[ The mm parts have been acked by VM people, and the series was
apparently in -mm for a while - Linus ]
* tag 'media/v4.3-2' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] drm/exynos: Convert g2d_userptr_get_dma_addr() to use get_vaddr_frames()
[media] media: vb2: Remove unused functions
[media] media: vb2: Convert vb2_dc_get_userptr() to use frame vector
[media] media: vb2: Convert vb2_vmalloc_get_userptr() to use frame vector
[media] media: vb2: Convert vb2_dma_sg_get_userptr() to use frame vector
[media] vb2: Provide helpers for mapping virtual addresses
[media] media: omap_vout: Convert omap_vout_uservirt_to_phys() to use get_vaddr_pfns()
[media] mm: Provide new get_vaddr_frames() helper
[media] vb2: Push mmap_sem down to memops
With two exceptions (drm/qxl and drm/radeon) all vm_operations_struct
structs should be constant.
Signed-off-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Reviewed-by: Oleg Nesterov <oleg@redhat.com>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=cIed
-----END PGP SIGNATURE-----
Merge tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- new DVB frontend drivers: ascot2e, cxd2841er, horus3a, lnbh25
- new HDMI capture driver: tc358743
- new driver for NetUP DVB new boards (netup_unidvb)
- IR support for DVBSky cards (smipcie-ir)
- Coda driver has gain macroblock tiling support
- Renesas R-Car gains JPEG codec driver
- new DVB platform driver for STi boards: c8sectpfe
- added documentation for the media core kABI to device-drivers DocBook
- lots of driver fixups, cleanups and improvements
* tag 'media/v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (297 commits)
[media] c8sectpfe: Remove select on undefined LIBELF_32
[media] i2c: fix platform_no_drv_owner.cocci warnings
[media] cx231xx: Use wake_up_interruptible() instead of wake_up_interruptible_nr()
[media] tc358743: only queue subdev notifications if devnode is set
[media] tc358743: add missing Kconfig dependency/select
[media] c8sectpfe: Use %pad to print 'dma_addr_t'
[media] DocBook media: Fix typo "the the" in xml files
[media] tc358743: make reset gpio optional
[media] tc358743: set direction of reset gpio using devm_gpiod_get
[media] dvbdev: document most of the functions/data structs
[media] dvb_frontend.h: document the struct dvb_frontend
[media] dvb-frontend.h: document struct dtv_frontend_properties
[media] dvb-frontend.h: document struct dvb_frontend_ops
[media] dvb: Use DVBFE_ALGO_HW where applicable
[media] dvb_frontend.h: document struct analog_demod_ops
[media] dvb_frontend.h: Document struct dvb_tuner_ops
[media] Docbook: Document struct analog_parameters
[media] dvb_frontend.h: get rid of dvbfe_modcod
[media] add documentation for struct dvb_tuner_info
[media] dvb_frontend: document dvb_frontend_tune_settings
...
This change modifies gen_pool_get() and devm_gen_pool_create() client
interfaces adding one more argument "name" of a gen_pool object.
Due to implementation gen_pool_get() is capable to retrieve only one
gen_pool associated with a device even if multiple gen_pools are created,
fortunately right at the moment it is sufficient for the clients, hence
provide NULL as a valid argument on both producer devm_gen_pool_create()
and consumer gen_pool_get() sides.
Because only one created gen_pool per device is addressable, explicitly
add a restriction to devm_gen_pool_create() to create only one gen_pool
per device, this implies two possible error codes returned by the
function, account it on client side (only misc/sram). This completes
client side changes related to genalloc updates.
[akpm@linux-foundation.org: gen_pool_get() cleanup]
Signed-off-by: Vladimir Zapolskiy <vladimir_zapolskiy@mentor.com>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Jean-Christophe Plagniol-Villard <plagnioj@jcrosoft.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc
versions of the descriptor calls that did not use the flags
argument on the end. This was around for too long and eventually
Uwe Kleine-König took the time to clean it out and the last
users are removed along with the macros in this tag. In several
cases the use of flags simplifies the code. For this reason we
have (ACKed) patches hitting in DRM, IIO, media, NFC, USB+PHY
up until we hammer in the nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff
we have i the kernel to discourage people from reinventing
a square wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO
IRQ chip instead of using one class for all chips, as the current
code will not work with systems with several GPIO chips doing
lockdep debugging.
- Protect against driver unloading also when a GPIO line is only
used as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent
device driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing
all call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a
combined call to irq_set_chained_handler_and_data(). This
series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which
is way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs
from IRQ numbers. The goal is to get rid of the irq number
from the handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO
drivers. This was an ARM specific function that is replaced
with the generic irq_modify_status() where special flags
are actually needed.
- When an OF node has a pin range for its GPIOs, return
-EPROBE_DEFER if the pin controller isn't available.
Pretty logical, yet needed to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own
irq_*_resources call back, then call these instead of the
defaults provided by the GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not
properly documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the
generic GPIO driver.
- Clean out platform data support from the Emma Mobile (EM)
driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver,
we now support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver.
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=iQ2P
-----END PGP SIGNATURE-----
Merge tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.3 kernel cycle.
There is quite a lot going on in the GPIO subsystem this merge window,
so the main matter is decribed below.
The hits in other subsystems when making the GPIO flags optional are
all ACKed by their respective subsystem maintainers.
Core changes:
- Root out the wrapper devm_gpiod_get() and gpiod_get() etc versions
of the descriptor calls that did not use the flags argument on the
end. This was around for too long and eventually Uwe Kleine-König
took the time to clean it out and the last users are removed along
with the macros in this tag. In several cases the use of flags
simplifies the code. For this reason we have (ACKed) patches
hitting in DRM, IIO, media, NFC, USB+PHY up until we hammer in the
nail with removing the macros.
- Add a fat document describing how much ready-made GPIO stuff we
have i the kernel to discourage people from reinventing a square
wheel in userspace, as so often happens.
- Create a separate lockdep class for each instance of a GPIO IRQ
chip instead of using one class for all chips, as the current code
will not work with systems with several GPIO chips doing lockdep
debugging.
- Protect against driver unloading also when a GPIO line is only used
as IRQ for the GPIOLIB_IRQCHIP helpers.
- If the GPIO chip has no designated owner, assign the parent device
driver owner as owner.
- Consolidation of chained IRQ handler install/remove replacing all
call sites where irq_set_handler_data() and
irq_set_chained_handler() were done in succession with a combined
call to irq_set_chained_handler_and_data().
This series was created by Thomas Gleixner after the problem was
observed by Russell King.
- Tglx also made another series of patches switching
__irq_set_handler_locked() for irq_set_handler_locked() which is
way cleaner.
- Tglx and Jiang Liu wrote a good bunch of patches to make use of
irq_desc_get_xxx() accessors and avoid looking up irq_descs from
IRQ numbers. The goal is to get rid of the irq number from the
handlers in the IRQ flow which is nice.
- Rob Herring killed off the set_irq_flags() for all GPIO drivers.
This was an ARM specific function that is replaced with the generic
irq_modify_status() where special flags are actually needed.
- When an OF node has a pin range for its GPIOs, return -EPROBE_DEFER
if the pin controller isn't available. Pretty logical, yet needed
to be fixed.
- If a driver using GPIOLIB_IRQCHIP has its own irq_*_resources call
back, then call these instead of the defaults provided by the
GPIOLIB.
- Fix an undocumented ABI hole: named GPIOs were not properly
documented.
Driver improvements:
- Add get_direction() support to the generic GPIO driver, it's
strange that we didn't have that before.
- Make it possible to have input-only GPIO chips using the generic
GPIO driver.
- Clean out platform data support from the Emma Mobile (EM) driver
- Finegrained runtime PM support for the RCAR driver.
- Support r8a7795 (R-car H3) in the RCAR driver.
- Support interrupts on GPIOs 16 thru 31 in the DaVinci driver.
- Some consolidation and new support in the MPC8xxx driver, we now
support MPC5125.
- Preempt-RT-friendly patches: the OMAP, MPC8xxx, drivers uses raw
spinlocks making it work better with the realime patches.
- Interrupt support for the EXTRAXFS GPIO driver.
- Make the ETRAXFS GPIO driver support also ARTPEC-3.
- Interrupt and wakeup support for the BRCMSTB driver, also for
wakeup from S5 cold boot.
- Mask MXC IRQs during suspend.
- Improve OMAP2 GPIO set_debounce() to work according to spec.
- The VF610 driver handles IRQs properly.
New drivers:
- ZTE ZX GPIO driver"
* tag 'gpio-v4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (87 commits)
Revert "gpio: extraxfs: fix returnvar.cocci warnings"
gpio: tc3589x: use static container helper
gpio: xlp: fix error return code
gpio: vf610: handle level IRQ's properly
gpio: max732x: Fix error handling in probe()
gpio: omap: fix clk_prepare/unprepare usage
gpio: omap: protect regs access in omap_gpio_irq_handler
gpio: omap: fix omap2_set_gpio_debounce
gpio: omap: switch to use platform_get_irq
gpio: omap: remove wrong irq_domain_remove usage in probe
gpiolib: add description for gpio irqchip fields in struct gpio_chip
gpio: extraxfs: fix returnvar.cocci warnings
gpiolib: irqchip: use different lockdep class for each gpio irqchip
gpio/grgpio: fix deadlock in grgpio_irq_unmap()
Documentation: gpio: consumer: describe active low property
gpio: mxc: fix section mismatch warning
gpio/mxc: mask gpio interrupts in suspend
gpio: omap: Fix missing raw locks conversion
gpio: brcmstb: support wakeup from S5 cold boot
gpio: brcmstb: Add interrupt and wakeup source support
...
LIBELF_32 is not defined in Kconfig, and is left over legacy
which is not required in the upstream driver, so remove it.
Suggested-by: Valentin Rothberg <valentinrothberg@gmail.com>
Signed-off-by: Peter Griffin <peter.griffin@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
drivers/media/i2c/tc358743.c:1960:3-8: No need to set .owner here. The core will do it.
Remove .owner field if calls are used which set it automatically
Generated by: scripts/coccinelle/api/platform_no_drv_owner.cocci
CC: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
While looking at use cases of the wake queues in order to add support
for simple wait queues, I noticed that there was only a single user of
wake_up_interruptible_nr(), and that use was doing a single task wake
up. Have that user use the proper wake_up_interruptible() instead, and
perhaps we can even remove the function wake_up_interruptible_nr().
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Hardware interrupts are enabled in the probe function, before the subdev
is registered to its v4l2_device. Until v4l2_device_register_subdev_node
is called, sd->devnode is NULL and v4l2_subdev_notify_event must not be
called.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
As reported by Randy:
> when CONFIG_MEDIA_CONTROLLER is not enabled:
>
> ../drivers/media/i2c/tc358743.c: In function 'tc358743_probe':
> ../drivers/media/i2c/tc358743.c:1890:29: error: 'struct v4l2_subdev' has no member named 'entity'
> err = media_entity_init(&sd->entity, 1, &state->pad, 0);
> ^
> ../drivers/media/i2c/tc358743.c:1940:26: error: 'struct v4l2_subdev' has no member named 'entity'
> media_entity_cleanup(&sd->entity);
> ^
> ../drivers/media/i2c/tc358743.c: In function 'tc358743_remove':
> ../drivers/media/i2c/tc358743.c:1955:26: error: 'struct v4l2_subdev' has no member named 'entity'
> media_entity_cleanup(&sd->entity);
> ^
This driver depends on VIDEO_V4L2_SUBDEV_API and needs to select HDMI.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Use %pad to print 'dma_addr_t' in order to fix the following
build warning:
drivers/media/platform/sti/c8sectpfe/c8sectpfe-core.c:588:2: warning: format '%x' expects argument of type 'unsigned int', but argument 5 has type 'dma_addr_t' [-Wformat=]
Reported-by: Olof's autobuilder <build@lixom.net>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 2561482468 ("[media] tc358743: support probe from device tree")
specified in the device tree binding documentation that the reset gpio
is optional. Make the implementation match accordingly.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Commit 2561482468 ("[media] tc358743: support probe from device tree")
failed to explicitly set the direction of the reset gpio. Use the
optional flag of devm_gpiod_get to make up leeway.
This is also necessary because the flag parameter will become mandatory
soon.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Document the most relevant functions and data structs for
developers that are working with the DVB subsystem.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
That struct is used on every DVB Front End driver, as it
contains what's needed to register/use a frontend at the
Kernel.
Document it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Most of the parameters here are already well defined at
the userspace documentation. Yet, it is good to add some
documentation, for the developers to be sure that they
are the same as the ones at userspace API.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
This is one of the most important functions of the DVB
frontend, containing the logic needed to set the parameters
at the demux and to send commands via SEC.
Document it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
The dvb_frontend.c core defines a FE_ALGO_HW symbol that it is
never used. Also, both cx24123 returns 1 to get_algo() callback
instead of using DVBFE_ALGO_HW.
Probably, those are some left overs from some code cleanup.
Let's stop returning magic numbers and use the proper macro
value.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
The struct dvb_tuner_ops contains lots of callbacks used
by tuners. Document them.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
That struct inside dvb-frontend.h stores some parameters
from V4L2 API (videodev2.h), in order to be used by the
hybrid analog/digital TV tuners.
Document it.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
This enum is not used anymore, as drivers use the
modulation definitions from the public API. It is probably
a left over from some DVB core cleanup.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
Despite being used everywhere at DVB frontends, the
struct dvb_tuner_info were never documented.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
There are already some comments at dvb_ringbuffer.h that are ready
for DocBook, although not properly formatted.
Convert them, fix some issues and add this file to
the device-drivers DocBook.
While here, put multi-line comments on the right format.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
There are already some comments at dvb_math.h that are ready
for DocBook, although not properly formatted.
Convert them, fix some issues and add this file to
the device-drivers DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
There are already some comments at dvb_frontend.h that are ready
for DocBook, although not properly formatted.
Convert them, and add this file to the device-drivers DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
There are already some tags at dvb_ca_en50221.h, but using a
different format. Convert them, fix a few entries and add
to the device-drivers DocBook.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
There are lots of docbook marks at the media subsystem, but
those aren't used.
Add the core headers/code in order to start generating docs.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Acked-by: Jonathan Corbet <corbet@lwn.net>
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=TqKo
-----END PGP SIGNATURE-----
Merge tag 'media/v4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
- a regression fix at the videobuf2 core driver
- fix error handling at mantis probing code
- revert the IR encode patches, as the API is not mature enough.
So, better to postpone the changes to a latter Kernel
- fix Kconfig breakages on some randconfig scenarios.
* tag 'media/v4.2-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] mantis: Fix error handling in mantis_dma_init()
Revert "[media] rc: rc-ir-raw: Add scancode encoder callback"
Revert "[media] rc: rc-ir-raw: Add Manchester encoder (phase encoder) helper"
Revert "[media] rc: ir-rc5-decoder: Add encode capability"
Revert "[media] rc: ir-rc6-decoder: Add encode capability"
Revert "[media] rc: rc-core: Add support for encode_wakeup drivers"
Revert "[media] rc: rc-loopback: Add loopback of filter scancodes"
Revert "[media] rc: nuvoton-cir: Add support for writing wakeup samples via sysfs filter callback"
[media] vb2: Fix compilation breakage when !CONFIG_BUG
[media] vb2: Only requeue buffers immediately once streaming is started
[media] media/pci/cobalt: fix Kconfig and build when SND is not enabled
[media] media/dvb: fix ts2020.c Kconfig and build
Current code assigns 0 to variable 'err', which makes mantis_dma_init()
to return success even if mantis_alloc_buffers() fails.
Fix it by checking the return value from mantis_alloc_buffers() and
propagating it in the case of error.
Reported-by: RUC_Soft_Sec <zy900702@163.com>
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 9869da5bac.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 1d971d927e.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit a0466f15b4.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit cf257e288a.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 0d830b2d12.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit 2e4ebde269.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
This reverts commit da7ee60b03.
The current code is not mature enough, the API should allow a single
protocol to be specified. Also, the current code contains heuristics
that will depend on module load order.
Signed-off-by: David Härdeman <david@hardeman.nu>
Acked-by: Antti Seppälä <a.seppala@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
Antti Palosaari