Add documentation for a new optional property local-mac-address which
is described in ethernet.txt.
Signed-off-by: xiaofeis <xiaofeis@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add properties to support all Phy config
PHY_MODE (MII,GMII, RMII, RGMII) and in normal, PHY wo crystal (25Mhz),
PHY wo crystal (50Mhz), No 125Mhz from PHY config.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
- Support for the MIPSr6 MemoryMapID register & Global INValidate TLB
(GINVT) instructions, allowing for more efficient TLB maintenance when
running on a CPU such as the I6500 that supports these.
- Enable huge page support for MIPS64r6.
- Optimize post-DMA cache sync by removing that code entirely for kernel
configurations in which we know it won't be needed.
- The number of pages allocated for interrupt stacks is now calculated
correctly, where before we would wastefully allocate too much memory
in some configurations.
- The ath79 platform migrates to devicetree.
- The bcm47xx platform sees fixes for the Buffalo WHR-G54S board.
- The ingenic/jz4740 platform gains support for appended devicetrees.
- The cavium_octeon, lantiq, loongson32 & sgi-ip27 platforms all see
cleanups as do various pieces of core architecture code.
-----BEGIN PGP SIGNATURE-----
iIsEABYIADMWIQRgLjeFAZEXQzy86/s+p5+stXUA3QUCXH3BQxUccGF1bC5idXJ0
b25AbWlwcy5jb20ACgkQPqefrLV1AN1+4wD+Oh4JTfZN/NEOQMlrSkXxjEHqjX3u
1Y6CiiPCs+q2UnYBANb+ic+ZH5MnvJxxmcvlYI2q3rIh4b8TDriip4KMUTUP
=Sw9X
-----END PGP SIGNATURE-----
Merge tag 'mips_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux
Pull MIPS updates from Paul Burton:
- Support for the MIPSr6 MemoryMapID register & Global INValidate TLB
(GINVT) instructions, allowing for more efficient TLB maintenance
when running on a CPU such as the I6500 that supports these.
- Enable huge page support for MIPS64r6.
- Optimize post-DMA cache sync by removing that code entirely for
kernel configurations in which we know it won't be needed.
- The number of pages allocated for interrupt stacks is now calculated
correctly, where before we would wastefully allocate too much memory
in some configurations.
- The ath79 platform migrates to devicetree.
- The bcm47xx platform sees fixes for the Buffalo WHR-G54S board.
- The ingenic/jz4740 platform gains support for appended devicetrees.
- The cavium_octeon, lantiq, loongson32 & sgi-ip27 platforms all see
cleanups as do various pieces of core architecture code.
* tag 'mips_5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (66 commits)
MIPS: lantiq: Remove separate GPHY Firmware loader
MIPS: ingenic: Add support for appended devicetree
MIPS: SGI-IP27: rework HUB interrupts
MIPS: SGI-IP27: do boot CPU init later
MIPS: SGI-IP27: do xtalk scanning later
MIPS: SGI-IP27: use pr_info/pr_emerg and pr_cont to fix output
MIPS: SGI-IP27: clean up bridge access and header files
MIPS: SGI-IP27: get rid of volatile and hubreg_t
MIPS: irq: Allocate accurate order pages for irq stack
MIPS: dma-noncoherent: Remove bogus condition in dma_sync_phys()
MIPS: eBPF: Remove REG_32BIT_ZERO_EX
MIPS: eBPF: Always return sign extended 32b values
MIPS: CM: Fix indentation
MIPS: BCM47XX: Fix/improve Buffalo WHR-G54S support
MIPS: OCTEON: program rx/tx-delay always from DT
MIPS: OCTEON: delete board-specific link status
MIPS: OCTEON: don't lie about interface type of CN3005 board
MIPS: OCTEON: warn if deprecated link status is being used
MIPS: OCTEON: add fixed-link nodes to in-kernel device tree
MIPS: Delete unused flush_cache_sigtramp()
...
Pull crypto update from Herbert Xu:
"API:
- Add helper for simple skcipher modes.
- Add helper to register multiple templates.
- Set CRYPTO_TFM_NEED_KEY when setkey fails.
- Require neither or both of export/import in shash.
- AEAD decryption test vectors are now generated from encryption
ones.
- New option CONFIG_CRYPTO_MANAGER_EXTRA_TESTS that includes random
fuzzing.
Algorithms:
- Conversions to skcipher and helper for many templates.
- Add more test vectors for nhpoly1305 and adiantum.
Drivers:
- Add crypto4xx prng support.
- Add xcbc/cmac/ecb support in caam.
- Add AES support for Exynos5433 in s5p.
- Remove sha384/sha512 from artpec7 as hardware cannot do partial
hash"
[ There is a merge of the Freescale SoC tree in order to pull in changes
required by patches to the caam/qi2 driver. ]
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (174 commits)
crypto: s5p - add AES support for Exynos5433
dt-bindings: crypto: document Exynos5433 SlimSSS
crypto: crypto4xx - add missing of_node_put after of_device_is_available
crypto: cavium/zip - fix collision with generic cra_driver_name
crypto: af_alg - use struct_size() in sock_kfree_s()
crypto: caam - remove redundant likely/unlikely annotation
crypto: s5p - update iv after AES-CBC op end
crypto: x86/poly1305 - Clear key material from stack in SSE2 variant
crypto: caam - generate hash keys in-place
crypto: caam - fix DMA mapping xcbc key twice
crypto: caam - fix hash context DMA unmap size
hwrng: bcm2835 - fix probe as platform device
crypto: s5p-sss - Use AES_BLOCK_SIZE define instead of number
crypto: stm32 - drop pointless static qualifier in stm32_hash_remove()
crypto: chelsio - Fixed Traffic Stall
crypto: marvell - Remove set but not used variable 'ivsize'
crypto: ccp - Update driver messages to remove some confusion
crypto: adiantum - add 1536 and 4096-byte test vectors
crypto: nhpoly1305 - add a test vector with len % 16 != 0
crypto: arm/aes-ce - update IV after partial final CTR block
...
Pull networking updates from David Miller:
"Here we go, another merge window full of networking and #ebpf changes:
1) Snoop DHCPACKS in batman-adv to learn MAC/IP pairs in the DHCP
range without dealing with floods of ARP traffic, from Linus
Lüssing.
2) Throttle buffered multicast packet transmission in mt76, from
Felix Fietkau.
3) Support adaptive interrupt moderation in ice, from Brett Creeley.
4) A lot of struct_size conversions, from Gustavo A. R. Silva.
5) Add peek/push/pop commands to bpftool, as well as bash completion,
from Stanislav Fomichev.
6) Optimize sk_msg_clone(), from Vakul Garg.
7) Add SO_BINDTOIFINDEX, from David Herrmann.
8) Be more conservative with local resends due to local congestion,
from Yuchung Cheng.
9) Allow vetoing of unsupported VXLAN FDBs, from Petr Machata.
10) Add health buffer support to devlink, from Eran Ben Elisha.
11) Add TXQ scheduling API to mac80211, from Toke Høiland-Jørgensen.
12) Add statistics to basic packet scheduler filter, from Cong Wang.
13) Add GRE tunnel support for mlxsw Spectrum-2, from Nir Dotan.
14) Lots of new IP tunneling forwarding tests, also from Nir Dotan.
15) Add 3ad stats to bonding, from Nikolay Aleksandrov.
16) Lots of probing improvements for bpftool, from Quentin Monnet.
17) Various nfp drive #ebpf JIT improvements from Jakub Kicinski.
18) Allow #ebpf programs to access gso_segs from skb shared info, from
Eric Dumazet.
19) Add sock_diag support for AF_XDP sockets, from Björn Töpel.
20) Support 22260 iwlwifi devices, from Luca Coelho.
21) Use rbtree for ipv6 defragmentation, from Peter Oskolkov.
22) Add JMP32 instruction class support to #ebpf, from Jiong Wang.
23) Add spinlock support to #ebpf, from Alexei Starovoitov.
24) Support 256-bit keys and TLS 1.3 in ktls, from Dave Watson.
25) Add device infomation API to devlink, from Jakub Kicinski.
26) Add new timestamping socket options which are y2038 safe, from
Deepa Dinamani.
27) Add RX checksum offloading for various sh_eth chips, from Sergei
Shtylyov.
28) Flow offload infrastructure, from Pablo Neira Ayuso.
29) Numerous cleanups, improvements, and bug fixes to the PHY layer
and many drivers from Heiner Kallweit.
30) Lots of changes to try and make packet scheduler classifiers run
lockless as much as possible, from Vlad Buslov.
31) Support BCM957504 chip in bnxt_en driver, from Erik Burrows.
32) Add concurrency tests to tc-tests infrastructure, from Vlad
Buslov.
33) Add hwmon support to aquantia, from Heiner Kallweit.
34) Allow 64-bit values for SO_MAX_PACING_RATE, from Eric Dumazet.
And I would be remiss if I didn't thank the various major networking
subsystem maintainers for integrating much of this work before I even
saw it. Alexei Starovoitov, Daniel Borkmann, Pablo Neira Ayuso,
Johannes Berg, Kalle Valo, and many others. Thank you!"
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (2207 commits)
net/sched: avoid unused-label warning
net: ignore sysctl_devconf_inherit_init_net without SYSCTL
phy: mdio-mux: fix Kconfig dependencies
net: phy: use phy_modify_mmd_changed in genphy_c45_an_config_aneg
net: dsa: mv88e6xxx: add call to mv88e6xxx_ports_cmode_init to probe for new DSA framework
selftest/net: Remove duplicate header
sky2: Disable MSI on Dell Inspiron 1545 and Gateway P-79
net/mlx5e: Update tx reporter status in case channels were successfully opened
devlink: Add support for direct reporter health state update
devlink: Update reporter state to error even if recover aborted
sctp: call iov_iter_revert() after sending ABORT
team: Free BPF filter when unregistering netdev
ip6mr: Do not call __IP6_INC_STATS() from preemptible context
isdn: mISDN: Fix potential NULL pointer dereference of kzalloc
net: dsa: mv88e6xxx: support in-band signalling on SGMII ports with external PHYs
cxgb4/chtls: Prefix adapter flags with CXGB4
net-sysfs: Switch to bitmap_zalloc()
mellanox: Switch to bitmap_zalloc()
bpf: add test cases for non-pointer sanitiation logic
mlxsw: i2c: Extend initialization by querying resources data
...
-----BEGIN PGP SIGNATURE-----
iHUEABYIAB0WIQQUwxxKyE5l/npt8ARiEGxRG/Sl2wUCXH2D9wAKCRBiEGxRG/Sl
2xRxAQDl+fx3qSZvyKFEdeklwz0EdBZyAGP9Jd9aU5AaVnJz5QD9EIh77Ii/HC1t
Cm6TeM3kfF7JYcqfPlONJqhF4Bgb/A4=
=y0aX
-----END PGP SIGNATURE-----
Merge tag 'leds-for-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds
Pull LED updates from Jacek Anaszewski:
- finalize previously announced support for initialization of pattern
triggers from Device Tree
- fix for null deref on firmware load failure in leds-lp55xx-common.c
* tag 'leds-for-5.1-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
leds: lp55xx: fix null deref on firmware load failure
leds: trigger: timer: Add initialization from Device Tree
leds: trigger: oneshot: Add initialization from Device Tree
leds: trigger: pattern: Add pattern initialization from Device Tree
leds: Add helper for getting default pattern from Device Tree
dt-bindings: leds: Add pattern initialization from Device Tree
Add support for LM96000, DPS-650AB to existing drivers
Use permission specific SENSOR[_DEVICE]_ATTR variants in several drivers
Replace S_<PERMS> with octal values in several drivers
Update some license headers
Various minor fixes and improvements in several drivers
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1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=rJSN
-----END PGP SIGNATURE-----
Merge tag 'hwmon-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- Add support for LM96000, DPS-650AB to existing drivers
- Use permission specific SENSOR[_DEVICE]_ATTR variants in several
drivers
- Replace S_<PERMS> with octal values in several drivers
- Update some license headers
- Various minor fixes and improvements in several drivers
* tag 'hwmon-for-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (89 commits)
dt-bindings: hwmon: Add missing documentation for lm75
hwmon: (ad7418) Add device tree probing
hwmon: (ad741x) Add DT bindings for Analog Devices AD741x
hwmon: (ntc_thermistor) Convert to new hwmon API
hwmon: (pwm-fan) Add optional regulator support
dt-bindings: hwmon: Add optional regulator support to pwm-fan
hwmon: (f71882fg) Mark expected switch fall-through
hwmon: (ad7418) Catch I2C errors
hwmon: (lm85) add support for LM96000 high frequencies
hwmon: (lm85) support the LM96000
dt-bindings: Add LM96000 as a trivial device
hwmon: (lm85) remove freq_map size hardcodes
hwmon: (occ) Fix license headers
hwmon: (via-cputemp) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (vexpress-hwmon) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (tmp421) Replace S_<PERMS> with octal values
hwmon: (tmp103) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (tmp102) Replace S_<PERMS> with octal values
hwmon: (tc74) Use permission specific SENSOR[_DEVICE]_ATTR variants
hwmon: (tc654) Use permission specific SENSOR[_DEVICE]_ATTR variants
...
A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
- Support for inter-word delays.
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects.
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlx9WtETHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DfrB/92O47HJfHg1xIgOp4BLzT8lA5zQEsy
a8ApcLVLvY6mSfbB/G7RosfoPwTc1eZP5Q2BqzQOBIO+507ao4AcASARmkTwjwkC
eRUJ/THkGyGurs8POtnc5YJlHsT1t743QpqlUNekt+NqognlkPccgc5bNgixfuPD
eVSwVC85SKP3gCpAjVb6FFFmlWr8AKdlgx+41h9QpMNG/85H6xgo4C4Wlajt42/E
wNx+WXzlPyzB5Lc3IGPeF/I/Hu/Ta3hUZLTVpWi5ubM8p4SYGmMZ9l8sURPCz1pK
UMZFpJxx8DWwkj2F/FkoLasfiRqUHIP9K7NfKF0u2xdNbhEk1GA3NAG0
=ctKG
-----END PGP SIGNATURE-----
Merge tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi updates from Mark Brown:
"A fairly quiet release for SPI, the biggest thing is the conversion to
use GPIO descriptors which is now 90% done but still needs some
stragglers converting.
Summary:
- Support for inter-word delays
- Conversion of the core and most drivers to use GPIO descriptors for
GPIO controlled chip selects
- New drivers for NXP FlexSPI and QuadSPI, SiFive and Spreadtrum"
* tag 'spi-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi: (104 commits)
spi: sh-msiof: Restrict bits per word to 8/16/24/32 on R-Car Gen2/3
spi: sifive: Remove redundant dev_err call in sifive_spi_probe()
spi: sifive: Remove spi_master_put in sifive_spi_remove()
spi: spi-gpio: fix SPI_CS_HIGH capability
spi: pxa2xx: Setup maximum supported DMA transfer length
spi: sifive: Add driver for the SiFive SPI controller
spi: sifive: Add DT documentation for SiFive SPI controller
spi: sprd: Add a prefix for SPI DMA channel macros
spi: sprd: spi: sprd: Add DMA mode support
dt-bindings: spi: Add the DMA properties for the SPI dma mode
spi: sprd: Add the SPI irq function for the SPI DMA mode
dt-bindings: spi: imx: Add an entry for the i.MX8QM compatible
spi: use gpio[d]_set_value_cansleep for setting chipselect GPIO
spi: gpio: Advertise support for SPI_CS_HIGH
spi: sh-msiof: Replace spi_master by spi_controller
spi: sh-hspi: Replace spi_master by spi_controller
spi: rspi: Replace spi_master by spi_controller
spi: atmel-quadspi: add support for sam9x60 qspi controller
dt-bindings: spi: atmel-quadspi: QuadSPI driver for Microchip SAM9X60
spi: atmel-quadspi: add support for named peripheral clock
...
The bulk of the standout changes in this release are cleanups, with the
core work being a combination of factoring out common code into helpers
and the completion of the conversion of the core to use GPIO
descriptors.
- Addition of helper functions for current limits and conversion of
drivers to use them by Axel Lin.
- Lots and lots of cleanups from Axel Lin.
- Conversion of the core to use GPIO descriptors rather than numbers by
Linus Walleij.
- New drivers for Maxim MAX77650 and ROHM BD70528.
-----BEGIN PGP SIGNATURE-----
iQFHBAABCgAxFiEEreZoqmdXGLWf4p/qJNaLcl1Uh9AFAlx9UosTHGJyb29uaWVA
a2VybmVsLm9yZwAKCRAk1otyXVSH0DR7B/4x2fjnrnlvDqwzr20jcWH0BTiOCN+s
JpWNn2HxoeNNOn2w52bo0WNBvXElWj5+Lik8xljlj9DWXCgSdys0z5XEOpOmg3Eg
+7AhyHmYBYf2igHWqw3dvL79n2MqdUY6mpbVtbf9kfJ3M5CwkwBUuXYNJLKZhLsm
r06wIaEmCDT9mQNxl7r1tbDUpN8Rjg43W4dNFMYEUnZPpd9zhdwSnTRFxqhpF+K+
GTli4yv3Z2IzZWGvG838/UBETffTfZv/lnuF7f/fagihGnhsp4RSp+3/PYvIV7/v
BIvPUywSXQFiC/NqqtRBkqRKEGclv0itZzZy39hl+zp/k+Im2jzH0gkP
=7lqn
-----END PGP SIGNATURE-----
Merge tag 'regulator-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator
Pull regulator updates from Mark Brown:
"The bulk of the standout changes in this release are cleanups, with
the core work being a combination of factoring out common code into
helpers and the completion of the conversion of the core to use GPIO
descriptors.
Summary:
- Addition of helper functions for current limits and conversion of
drivers to use them by Axel Lin.
- Lots and lots of cleanups from Axel Lin.
- Conversion of the core to use GPIO descriptors rather than numbers
by Linus Walleij.
- New drivers for Maxim MAX77650 and ROHM BD70528"
* tag 'regulator-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/regulator: (131 commits)
regulator: mc13xxx: Constify regulator_ops variables
regulator: palmas: Constify palmas_smps_ramp_delay array
regulator: wm831x-dcdc: Convert to use regulator_set/get_current_limit_regmap
regulator: pv88090: Convert to use regulator_set/get_current_limit_regmap
regulator: pv88080: Convert to use regulator_set/get_current_limit_regmap
regulator: pv88060: Convert to use regulator_set/get_current_limit_regmap
regulator: max77650: Convert to use regulator_set/get_current_limit_regmap
regulator: lp873x: Convert to use regulator_set/get_current_limit_regmap
regulator: lp872x: Convert to use regulator_set/get_current_limit_regmap
regulator: da9210: Convert to use regulator_set/get_current_limit_regmap
regulator: da9055: Convert to use regulator_set/get_current_limit_regmap
regulator: core: Add set/get_current_limit helpers for regmap users
regulator: Fix comment for csel_reg and csel_mask
regulator: stm32-vrefbuf: add power management support
regulator: 88pm8607: Remove unused fields from struct pm8607_regulator_info
regulator: 88pm8607: Simplify pm8607_list_voltage implementation
regulator: cpcap: Constify omap4_regulators and xoom_regulators
regulator: cpcap: Remove unused vsel_shift from struct cpcap_regulator
dt-bindings: regulator: tps65218: rectify units of LS3
dt-bindings: regulator: add LS2 load switch documentation
...
- mmc: core: Fixup max_discard/trim calculations
- mmc: core: Announce SD specs greater than 4.0
- mmc: core: Add discard support for SD cards
- mmc: core: Don't do retries for CMD6 (SWITCH command)
- mmc: core: Various cleanups and re-structuring
MMC host:
- cqhci: Add maintainers for eMMC CQHCI driver
- sdhci: Consolidate WP GPIO code
- sdhci: Add ADMA3 DMA support for V4 enabled host
- sdhci-pci-o2micro: Fixup card detect support
- sdhci-tegra: Add support for CMDQ
- sdhci-tegra: Support SDMMC pads auto-calibration
- sdhci-esdhc-imx: Add DCMD support and CMDQ support
- sdhci-esdhc-imx: Add support for i.MX6ULL variant
- sdhci-esdhc-imx: Fixup HS400 timing issue
- sdhci-esdhc-imx: Add HS400_ES support for i.MX8QXP
- renesas_sdhi: Avoid CRC errors by adjusting settings to speed mode
- renesas_sdhi: Fixup card initialization for high speed mode
- omap: Fixup timeout settings
- atmel-mci: Enable 8 bits bus-width support
- jz4740: Convert some legacy code to use modern APIs
- mmci: Send a CMD12 to clear DPSM at errors for STM32 sdmmc
-----BEGIN PGP SIGNATURE-----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=umka
-----END PGP SIGNATURE-----
Merge tag 'mmc-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC updates from Ulf Hansson:
"MMC core:
- Fixup max_discard/trim calculations
- Announce SD specs greater than 4.0
- Add discard support for SD cards
- Don't do retries for CMD6 (SWITCH command)
- Various cleanups and re-structuring
MMC host:
- cqhci:
* Add maintainers for eMMC CQHCI driver
- sdhci:
* Consolidate WP GPIO code
* Add ADMA3 DMA support for V4 enabled host
* Fixup card detect support in pci-o2micro driver
* Add support for CMDQ and SDMMC pads auto-calibration in tegra
driver
* Add DCMD support and CMDQ support, support for i.MX6ULL variant,
fixup HS400 timing issue and add HS400_ES support for i.MX8QXP
to esdhc-imx driver
* Avoid CRC errors by adjusting settings to speed mode and fixup
card initialization for high speed mode in renesas_sdhi
* Fixup timeout settings for omap
* Enable 8 bits bus-width support in atmel-mci
* Convert some legacy code in jz4740 driver to use modern APIs
* Send a CMD12 to clear DPSM at errors for STM32 sdmmc mmci
driver"
* tag 'mmc-v5.1' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: (69 commits)
mmc:fix a bug when max_discard is 0
mmc: core: Add a debug print when the card may have been replaced
mmc: core: Add sd discard timeout
mmc: core: Add discard support to sd
mmc: sdhci-esdhc-imx: clear the HALT bit when enable CQE
mmc: core: do not retry CMD6 in __mmc_switch()
mmc: core: Convert mmc_align_data_size() into an SDIO specific function
mmc: core: Move mmc_of_parse_voltage() to host.c
mmc: core: Convert mmc_regulator_get_ocrmask() to static
mmc: core: Move regulator helpers to separate file
mmc: of_mmc_spi: Convert to mmc_of_parse_voltage()
mmc: core: Drop retries as in-parameter to mmc_wait_for_app_cmd()
mmc: core: Convert mmc_wait_for_app_cmd() to static
mmc: renesas_sdhi: Change HW adjustment register according to speed mode
mmc: mmci: Send a CMD12 to clear the DPSM at errors
mmc: sdhci-xenon: Fixup already marked switch fall-through
mmc: sdhci-tegra: drop ->get_ro() implementation
mmc: sdhci-omap: drop ->get_ro() implementation
mmc: sdhci: use WP GPIO in sdhci_check_ro()
mmc: wmt-sdmmc: Drop unused include
...
- Use struct_size() where appropriate
- mtd_{read,write}() as wrappers around mtd_{read,write}_oob()
- Fix misuse of PTR_ERR() in docg3
- Coding style improvements in mtdcore.c
SPI NOR changes:
Core changes:
- Add support of octal mode I/O transfer
- Add a bunch of SPI NOR entries to the flash_info table
SPI NOR controller driver changes:
- cadence-quadspi:
* Add support for Octal SPI controller
* write upto 8-bytes data in STIG mode
- mtk-quadspi:
* rename config to a common one
* add SNOR_HWCAPS_READ to spi_nor_hwcaps mask
- Add Tudor as SPI-NOR co-maintainer
NAND changes
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
-----BEGIN PGP SIGNATURE-----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=wIHY
-----END PGP SIGNATURE-----
Merge tag 'mtd/for-5.1' of git://git.infradead.org/linux-mtd
Pull MTD updates from Boris Brezillon:
"Core MTD changes:
- Use struct_size() where appropriate
- mtd_{read,write}() as wrappers around mtd_{read,write}_oob()
- Fix misuse of PTR_ERR() in docg3
- Coding style improvements in mtdcore.c
SPI NOR changes:
Core changes:
- Add support of octal mode I/O transfer
- Add a bunch of SPI NOR entries to the flash_info table
SPI NOR controller driver changes:
- cadence-quadspi:
* Add support for Octal SPI controller
* write upto 8-bytes data in STIG mode
- mtk-quadspi:
* rename config to a common one
* add SNOR_HWCAPS_READ to spi_nor_hwcaps mask
- Add Tudor as SPI-NOR co-maintainer
NAND changes:
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting
various controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Check the return code of nand_reset() and nand_readid_op().
- Remove ->legacy.erase and single_erase().
- Simplify the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fix various possible object reference leaks (MTK, JZ4780, Atmel)
- ST:
* Add support for STM32 FMC2 NAND flash controller
- Meson:
* Add support for Amlogic NAND flash controller
- Denali:
* Several cleanup patches
- Sunxi:
* Several cleanup patches
- FSMC:
* Disable NAND on remove()
* Reset NAND timings on resume()
SPI-NAND drivers changes:
- Toshiba:
* Add support for all Toshiba products.
- Macronix:
* Fix ECC status read.
- Gigadevice:
* Add support for GD5F1GQ4UExxG"
* tag 'mtd/for-5.1' of git://git.infradead.org/linux-mtd: (64 commits)
mtd: spi-nor: Fix wrong abbreviation HWCPAS
mtd: spi-nor: cadence-quadspi: fix spelling mistake: "Couldnt't" -> "Couldn't"
mtd: spi-nor: Add support for en25qh64
mtd: spi-nor: Add support for MX25V8035F
mtd: spi-nor: Add support for EN25Q80A
mtd: spi-nor: cadence-quadspi: Add support for Octal SPI controller
dt-bindings: cadence-quadspi: Add new compatible for AM654 SoC
mtd: spi-nor: split s25fl128s into s25fl128s0 and s25fl128s1
mtd: spi-nor: cadence-quadspi: write upto 8-bytes data in STIG mode
mtd: spi-nor: Add support for mx25u3235f
mtd: rawnand: denali_dt: remove single anonymous clock support
mtd: rawnand: mtk: fix possible object reference leak
mtd: rawnand: jz4780: fix possible object reference leak
mtd: rawnand: atmel: fix possible object reference leak
mtd: rawnand: fsmc: Disable NAND on remove()
mtd: rawnand: fsmc: Reset NAND timings on resume()
mtd: spinand: Add support for GigaDevice GD5F1GQ4UExxG
mtd: rawnand: denali: remove unused dma_addr field from denali_nand_info
mtd: rawnand: denali: remove unused function argument 'raw'
mtd: rawnand: denali: remove unneeded denali_reset_irq() call
...
Document additional Microchip KSZ9477 family switches.
Show how KSZ8565 switch should be configured as the host port is port 7
instead of port 5.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Johan Hedberg says:
====================
pull request: bluetooth-next 2019-03-02
Here's one more bluetooth-next pull request for the 5.1 kernel:
- Added support for MediaTek MT7663U and MT7668U UART devices
- Cleanups & fixes to the hci_qca driver
- Fixed wakeup pin behavior for QCA6174A controller
Please let me know if there are any issues pulling. Thanks.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Update binding document with adding support of MT7663U and MT7668U UART
devices to mediatek-bluetooth.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Last set of patches. A new hardware support for mt76 otherwise quite
normal.
Major changes:
mt76
* add driver for MT7603E/MT7628
ath10k
* more preparation for SDIO support
wil6210
* support up to 20 stations in AP mode
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1
iQEcBAABAgAGBQJceUH5AAoJEG4XJFUm622bCsgH/RCWwW+QR6JEF3NCxJ980u0E
nreozLNjAyHGLh8apY7revFsWIRez/bEWdpGw1oVT6DGj2ksf0yVTKMHIwBiMUbE
Z0t3BMP2Yfc91KIBsmGlYr8xIKOQfv7RTaCj16W3Aj7zGbJum4UMgxE5xdboS6KF
DwhzGjJR7aK9mL+tgCs/A51aee0Q6WeP1BjvbzJUhvoqdsyXFxyTGivnqEwVY7G1
Mj63fjkrSMlYA4A3/tmkm1G/buAlfIk2qgWzwuxTk7/+HLIac4IVLno8GFCA3vDY
NlFcDrCsfQswWznz01gWlOUGe4bYO/IkB0diF+tVDNUqiVSOTblV+HeznQbDWBo=
=R94J
-----END PGP SIGNATURE-----
Merge tag 'wireless-drivers-next-for-davem-2019-03-01' of git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers-next
Kalle Valo says:
====================
wireless-drivers-next patches for 5.1
Last set of patches. A new hardware support for mt76 otherwise quite
normal.
Major changes:
mt76
* add driver for MT7603E/MT7628
ath10k
* more preparation for SDIO support
wil6210
* support up to 20 stations in AP mode
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
Define connection bindings (external PHY connections and internal links)
for the ENETC on-chip ethernet controllers.
Signed-off-by: Claudiu Manoil <claudiu.manoil@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
When we use the bindings defined in Documentation/devicetree/bindings/mux
to define mdio mux in producer and consumer terms, it results in two
devices. one is mux producer and other is mux consumer.
Add the bindings needed for Mdio mux consumer devices.
Signed-off-by: Pankaj Bansal <pankaj.bansal@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
There are two USB PID/VID variations I've seen for this chip, and I want
to utilize the 'interrupts' property defined here already.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
LS3 has a selectable current limit.
Change units to microamp in the example.
Signed-off-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Document device-tree settings of the load-switch LS2
in the tps65218 device.
Signed-off-by: Christian Hohnstaedt <Christian.Hohnstaedt@wago.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
In addition to MT7603E PCI devices, the driver supports the WLAN core on
MT7628/MT7688, which needs to be defined in DT.
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felix Fietkau <nbd@nbd.name>
The separate GPHY Firmware loader driver is not used any more, the GPHY
firmware is now loaded by the GSWIP switch driver which also makes use
of the GPHY.
Remove the old unused GPHY firmware loader driver.
The GPHY firmware is useless without an Ethernet and switch driver, it
should not harm if loading this does not work for system using an old
device tree.
I am not aware of any vendor separating the device tree from the kernel
binary, it should be ok to remove this.
The code and the functionality form this separate GPHY firmware loader
was added to the gswip driver in commit 14fceff477 ("net: dsa: Add
Lantiq / Intel DSA driver for vrx200")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Signed-off-by: Paul Burton <paul.burton@mips.com>
Cc: linux-mips@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: john@phrozen.org
Cc: netdev@vger.kernel.org
This adds device tree bindings for Analog Devices AD741x
as found in Gateway routers.
Cc: devicetree@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
-----BEGIN PGP SIGNATURE-----
iQEzBAABCgAdFiEE9HuaYnbmDhq/XIDIJWrqGEe9VoQFAlxwE4kACgkQJWrqGEe9
VoRQVQf+OOkScM6ZbsO2GbMRe0ybMOCOyBXfojPEGtVv80gHHrAPRocLqWMB1Xdb
MSfm7j+lyZU1I8eYVvdYXby7s5FlVWbrh8NSnnwox1QusdmyBm7vcxc6st15Poy/
/WtjE+Cry49eIx5L/pmmNH3AIqMdvSRTJD7NgOYjo/SIq4GLR+KQEgt1VLp/KyO0
TGeMDIT3Q3+MXVwvUh3YlHUwNJ2jOpjpPW94QxD0mef/b9doUlkvrOdHs3JeGQzX
aiiqWI1nRBmjNs34wp7Dyf3G/feplKyi+IS/ghTiijAgwbWdRI7KxrPtyCUYiint
3XqVgZAF/sfFaKFMIiJBMzoLQB15dQ==
=VbaE
-----END PGP SIGNATURE-----
Merge tag 'nand/for-5.1' of git://git.infradead.org/linux-mtd into mtd/next
NAND core changes:
- Fourth batch of fixes/cleanup to the raw NAND core impacting various
controller drivers (Sunxi, Marvell, MTK, TMIO, OMAP2).
- Checking the return code of nand_reset() and nand_readid_op().
- Removing ->legacy.erase and single_erase().
- Simplifying the locking.
- Several implicit fall through annotations.
Raw NAND controllers drivers changes:
- Fixing various possible object reference leaks (MTK, JZ4780, Atmel).
- ST:
* Adding support for STM32 FMC2 NAND flash controller.
- Meson:
* Adding support for Amlogic NAND flash controller.
- Denali:
* Several cleanup patches.
- Sunxi:
* Several cleanup patches.
- FSMC:
* Disabling NAND on remove().
* Resetting NAND timings on resume().
SPI-NAND drivers changes:
- Toshiba:
* Adding support for all Toshiba products.
- Macronix:
* Fixing ECC status read.
- Gigadevice:
* Adding support for GD5F1GQ4UExxG.
Add supports-cqe optional property for MMC hosts.
This property is used to identify the specific host controller
supporting command queue.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Thierry Reding <treding@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add pinctrls for 3V3 and 1V8 pad drive strength configuration for
Tegra210 sdmmc.
Tegra210 sdmmc has pad configuration registers in pinmux register
domain and handled thru pinctrl to pinmux device node.
Tegra186 and Tegra194 has pad configuration register with in the
SDMMC register domain itself and are handles thru drive strength
properties in sdmmc device node.
Signed-off-by: Sowjanya Komatineni <skomatineni@nvidia.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Add a imx6ull compatible string to be able to manage erratum ERR010450 on
i.MX6ULL.
Signed-off-by: Haibo Chen <haibo.chen@nxp.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
This adds an optional regulator support (e.g. switchable supply) to the
pwm fan binding.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
The FAN53526 differs from the FAN53555 only in that the mode bit in
VSEL0/VSEL1 is moved to the CONTROL register, the voltage selector mask
is extended by 1 bit and the step is different.
So extend the existing fan53555 driver to support FAN53526 as well.
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
DT documentation for SPI controller added.
Signed-off-by: Palmer Dabbelt <palmer@sifive.com>
Signed-off-by: Emil Renner Berthing <kernel@esmil.dk>
Signed-off-by: Yash Shah <yash.shah@sifive.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add support for active discharge for USB power switches.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Regulator high pull down are enabled by default so remove support in the
driver.
Signed-off-by: Pascal Paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The interrupt parent description is not needed as the parent is a parent
node with 'interrupt-controller' property.
Signed-off-by: pascal paillet <p.paillet@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
The LM96000 is a temperature sensor and fan controller based
on the LM85.
Signed-off-by: Jeremy Gebben <jgebben@sweptlaser.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
By default, ina3221, as a hardware monitor, continuously measures
the inputs and generates corresponding data. However, for battery
powered devices, this mode might be power consuming.
This patch adds a "ti,single-shot" property to allow changing the
default continuous mode to single-shot operating mode.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Bindings for Delta Electronics DPS-650-AB power supply.
Signed-off-by: Xiaoting Liu <xiaoting.liu@hxt-semitech.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Add ROHM BD71837 / BD71847 specific device tree bindings for
controlling the PMIC shutdown/reset states and voltages for
different HW states. The PMIC was designed to be used with NXP
i.MX8 SoC and it supports SNVS low power state which seems to
be typical for NXP i.MX SoCs. However, when SNVS is used we must
not allow SW to control enabling/disabling those regulators which
are crucial for system to boot as there is a HW limitation which
causes SW controlled regulators to be kept shut down after SNVS
reset.
Allow setting the SNVS to be used as reset target state and allow
marking those regulators which are critical for boot.
Signed-off-by: Matti Vaittinen <matti.vaittinen@fi.rohmeurope.com>
Tested-by: Angus Ainslie <angus@akkea.ca>
Reviewed-by: Angus Ainslie <angus@akkea.ca>
Signed-off-by: Mark Brown <broonie@kernel.org>
AM654 SoC has Cadence Octal SPI controller, which is similar to Cadence
QSPI controller but supports Octal IO(x8 data lines) and Double Data
Rate(DDR) mode. Add new compatible to support OSPI controller on TI's
AM654 SoCs.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Add the DMA properties for the SPI dma mode.
Signed-off-by: Lanqing Liu <lanqing.liu@unisoc.com>
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
Specify "little-endian" property if the 1588 timer IP block
is little-endian mode. The default endian mode is big-endian.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Add an entry for the "fsl,imx8mq-ecspi" compatible to describe
the ECSPI version present on i.MX8M.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
Add the compatibility sting documentation for sam9x60 10/100 interface.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
This removes a line left while adding the correct compatibility string for
sama5d3 10/100 interface. Now use the "atmel,sama5d3-macb" string.
Signed-off-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
xiaofeis